ENGLISH
Warnings, Cautions and Others / Mises en garde, précautions et indications diverses
USA ONLY
For U.S.A.
CAUTION
CAUTION
Battery shall not be exposed to excessive heat such as
sunshine, fire or the like.
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
ATTENTION
Les piles ne doivent en aucun cas être exposées à une
chaleur excessive (lumière du soleil, feu, etc.).
HOME THEATER SOUND SYSTEM
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
• When discarding batteries, environmental problems must
be considered and local rules or laws governing the disposal
of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION
TH-BC3
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
ATTENTION
• Ne bloquez pas les orifices ou les trous de ventilation. (Si
les orifices ou les trous de ventilation sont bloqués par un
journal un tissu, etc., la chaleur peut ne pas être évacuée
correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une
bougie, sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au
rebut des piles.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
This device compiles with RSS-210 of Industry Canada
Rules. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Pour les Etats-Unis
• N’exposez pas cet appareil à la pluie, à l’humidité, à un
égouttement ou à des éclaboussures et ne placez pas des
objets remplis de liquide, tels qu’un vase, sur l’appareil.
Le symbole de l’éclair à l’intérieur d’un triangle
Cet appareil est conforme au réglement CNR-210 de
l’industrie du Canada. L’utilisation de ce dispositif est
autorisée seulement aux conditions suivantes:
(1) il ne doit pas produire de brouillage et (2) l’utilisateur
du dispositif doit étre prét à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible
de compromettre le fonctionnement du dispositif.
équilatéral est destiné à alerter l’utilisateur sur
la présence d’une “tension dangereuse” non
isolée dans le boîtier du produit. Cette tension
est suffisante pour provoquer l’électrocution
de personnes.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by
the manufacturer for compliance could void the user’s
authority to operate the equipment.
Le point d’exclamation à l’intérieur d’un
triangle équilatéral est destiné à alerter
l’utilisateur sur la présence d’opérations
d’entretien importantes au sujet desquelles
des renseignements se trouvent dans le
manuel d’instructions.
For Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS
B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
Cet appareil est conforme à la partie 15 des règles
de la FCC (Federal Communications Commission). Le
fonctionnement est sujet aux deux conditions suivantes:
(1) Cet appareil ne peut pas causer d’interférences
nuisibles, et (2) cet appareil doit accepter toute
interférence reçue, y compris des interférences qui
peuvent causer un mauvais fonctionnement.
Tout changement ou modification non expressément
approuvés par le fabricant pour conformité peut annuler
l’autorité de l’utilisateur d’utiliser l’appareil.
CAUTION
The
button in any position does not disconnect the
Pour le Canada
mains line.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES
DE BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS
LA NORME SUR LE MATERIEL BROUILLEUR; “APPAREILS
NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES
COMMUNICATIONS.
Disconnect the mains plug to shut the power off
completely (the STANDBY lamp goes off). The MAINS plug
or an appliance coupler is used as the disconnect device,
the disconnect device shall remain readily operable.
When the System is on standby, the STANDBY lamp lights red.
When the System is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
Thank you for purchasing a JVC product.
Before operation, please read the instructions
carefully.
•
•
For U.S.A.
WARNING
ATTENTION
For customer use:
La touche
, dans n’importe quelle position, ne
Enter below the Model No. and Serial No. which are
located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE
THIS APPARATUS TO RAIN OR MOISTURE.
Pour les Etats-Unis
AVERTISSEMENT
POUR PRÉVENIR LES RISQUES D’INCENDIE OU DE CHOCS
ÉLECTRIQUES, NE PAS EXPOSER CE APPAREIL À LA PLUIE
OU À L’HUMIDITÉ.
déconnecte pas le système du secteur. Déconnectez la
fiche de secteur pour mettre l’appareil complètement hors
tension (le témoin STANDBY s’éteint). La fiche secteur ou
un coupleur est utilisé comme dispositif de déconnexion
de l’appareil, et l’appareil déconnecté doit être prêt à être
utilisé.
• Quand le système est en attente, le témoin STANDBY est
allumé en rouge.
• Quand le système est sous tension, le témoin STANDBY
s’éteint.
L’alimentation peut être télécommandée.
Model No.
Serial No.
GVT0327-002B[J]
1210WMKMDWJMM
INSTRUCTIONS
[European Union only]
[Union européenne seulement]
EN
© 2010 Victor Company of Japan, Limited
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas indicated by the dimensions in the illustration.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10
cm (3-15/16”) or more.
ATTENTION: Ventilation Correcte
Pour éviter tout risque de choc électrique et d’incendie, placez l’appareil en respectant ce qui suit:
1. Avant: Rien ne doit gêner le dégagement.
2. Flancs/Dessus/Arrière: Aucun obstacle ne doit être placé dans les zones indiquées par les dimensions dans
l’illustration.
3. Dessous: Poser l’appareil sur une surface plate. Laissez suffisamment d’espace pour que la ventilation puisse
s’effectuer correctement en plaçant l’appareil sur un socle d’une hauteur de 10 cm ou plus.
• “Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPod or iPhone may affect
wireless performance.
Playable iPod models
• Compatible iPod:
Introduction
Specifications
Troubleshooting
Do not block the vents
Blocking the vents may damage the System.
Care of the cabinet
• Stains on the System should be wiped off with a soft
cloth. If the System is heavily stained, wipe it with a cloth
soaked in water diluted neutral detergent and wrung
well, then wipe clean with a dry cloth.
Output power
60 W (30 W per channel-
If you have a problem with this System, check this list for a
possible solution before calling for service.
Auto power save function
Made for
iPod nano (6th generation)
iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod nano (2nd generation)
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod touch
Audio
Video
measure at 1 kHz Optical
Digital In at full scale
sinewave), RMS at 4 Ω at 1
kHz, with 10% total harmonic
distortion
When no operation is done in certain situations for 29
minutes, the unit turns off automatically. This function is
on at the initial setting. For details, refer to “Operations.”
*
POWER
Power does not come on.
= The power cord is not inserted securely. Plug it in
In this manual, the remote control buttons are used for
explaining the operations unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
securely.
Audio section
Analog Input
Digital Input*
• iPhone, iPod, iPod classic, iPod nano and iPod touch
are trademarks of Apple Inc., registered in the U.S.
and other countries.
The unit turns off suddenly.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
–
ANALOG: 1 Vrms/50 kΩ
DIGITAL 1 (OPTICAL) :
–21 dBm to –15 dBm (660 nm
30 nm)
= Auto power save function is on. Refer to “Activating/
deactivating APS (Auto Power Save)” in “Basic
operation.”
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinners, benzines or other
organic solvents including disinfectants.
– DO NOT apply any volatile substances such as
insecticides to it.
REMOTE CONTROL
Notes on handling
Important cautions
Installation of the System
DIGITAL 2 (COAXIAL) :
0.5 Vp-p/75 Ω
• HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
• HDCP is the abbreviation of “High-bandwidth Digital
Content Protection,” and is the high-reliable copy
control technology licensed by Digital Content
Protection, LLC.
Front / Face
The remote control does not work.
= Pull out the insulation sheet.
Speaker section
Type:
iPod classic
= Sunlight is shining directly on the remote sensor. Hide
the remote sensor from direct sunlight.
= The path between the remote control and the remote
sensor on the front panel is blocked.
Bass-Reflex Type
15 cm (5-15/16")
iPhone 4
• Select a place which is level, dry, and neither too hot nor
too cold; between 5°C and 35°C (41°F and 95°F).
• Leave sufficient distance between the System and the TV.
• Do not use the System in a location near heat sources,
or in a place subject to direct sunlight, excessive dust, or
vibration.
– DO NOT allow any rubber or plastic to remain in contact
with it for a long time.
• Do not place anything on top of the System. Doing so
may cause the System to fall, causing malfunctioning
and/or injury.
Speaker:
Woofer: 8 cm (3-3/16”) cone × 4
Tweeter: 2.5 cm (1”) balance
dome × 2
iPhone 3GS
15 cm
(5-15/16")
15 cm (5-15/16")
10 cm (3-15/16")
iPhone 3G
= Point the remote control at the remote sensor on the
Power Handling Capacity: 30 W
* Only for still picture
front panel.
Impedance:
Frequency Range:
Sound Pressure Level:
4 Ω
• The manufacturer accepts absolutely no liability for any
accidents or damage resulting from inadequate assembly
or mounting, insufficient strength of attachment, misuse
or abuse, or natural disasters.
• In this manual, “iPod” means iPod, iPod touch and
iPhone device. When iPod touch or iPhone device
is especially referred to, “iPod touch” or “iPhone” is
used.
= Signals cannot reach the remote sensor. Move closer to
the unit.
82 Hz to 25 kHz
88 dB/W•m
• Also refer to the instruction manual for iPod.
• If the NOT SUPP indicator is shown on the display, the
connected iPod is not supported.
• If iPod does not play correctly, update iPod software to
the latest version.
– For details about updating iPod, check on the Apple
web site <http://www.apple.com/>.
• Install the System in a location with adequate ventilation
to prevent internal heat buildup.
= The battery is exhausted. Replace the battery.
The remote control of the TV does not work.
= If you install the unit near the TV, connect the TV remote
pass through cable (supplied).
For U.S.A.
Power cord
General
Power Source (DC IN):
AC adaptor (AA-R1904):
Caution: Changes or modifications not expressly approved by party responsible for compliance could void the user’s
authority to operate the equipment.
• Do not handle the power cord with wet hands.
• A small amount of power is always consumed while the
power cord is connected to the wall outlet.
• Do not pull on the cord to unplug the power cord. When
unplugging the power cord, always grasp and pull the
plug so as not to damage the cord.
If water gets inside the System
DC 19 V
Input: AC 100 – 240 V
3.37 A
Turn the System off and disconnect the power cord from
the wall outlet, then call the store where you purchased
this System. Using the System in this condition may cause
a fire or electrical shock.
,
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Pour les Etats-Unis
50 Hz/60 Hz, 1.5 A – 0.9 A
Output: DC19 V
Power Consumption(in Standby mode):
0.50 W or less
Dimensions (W × H × D): 900 mm ×98 mm × 107 mm
(35-7/16”× 3-7/8”× 4-3/16”)
FM tuner
3.37 A
Hard to listen to broadcasts because of noise.
= Electrostatic discharge from your body may cause noise.
If this happens, turn off and on the unit again.
To prevent malfunctions of the System
• There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
• Do not insert any metallic objects or liquids into the
System.
Supplied accessories
External components
No sound can be heard when DIGITAL 1 or DIGITAL 2 is
selected as a source.
= Check the output setting of the connected digital
components. Set the output setting as the PCM signal
is outputted.
Check to make sure you have all of the supplied accessories.
If anything is missing, contact your dealer immediately.
• Remote control RM-STHBC3J (× 1)
• AC adaptor (AA-R1904) (× 1)
Mass:
3.4 kg (7.4 lbs)
Tuner
FM tuning range:
87.5 MHz – 108.0 MHz
DC 5 V 1 A
• AC power cord (× 1)
Safety precautions
Avoid moisture, water, and dust
Do not place the System in moist or dusty places.
Avoid high temperatures
Do not expose the System to direct sunlight and do not
place it near any heating devices.
When you are away
When away on holiday or for other reasons for an extended
period of time, disconnect the power cord from the wall
outlet.
• Lithium coin battery CR2025 (× 1)
– The battery has been installed in the remote control
when shipped from the factory.
iPod
iPod
Output power:
Attention: Les changements ou les modifications qui ne sont pas explicitement approuvés par la partie responsable de
l’observance pourraient mettre fin au droit de l’utilisateur d’utiliser le matériel.
iPod cannot be connected firmly.
= Check to see whether the connector between iPod and
the unit is not damaged, and connect it.
iPod does not provide sound.
• Core filter (× 2)
Remarque: Cet appareil a été testé et il s’est avéré conforme aux limites applicables à un appareil numérique de
classe B, en vertu de la Partie 15 des Règles de la FCC. Ces limites sont conçues de manière à assurer une protection
raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet appareil produit, utilise et peut
émettre une énergie de haute fréquence et, s’il n’est pas installé et utilisé en conformité avec les instructions, il peut
causer des interférences nuisibles aux communications radio. Il n’y a, toutefois, aucune garantie que des interférences
ne se produiront pas dans une installation particulière. Si cet appareil cause effectivement des interférences nuisibles
à la réception de la radio ou de la télévision, ce qu’on peut établir en mettant l’appareil en marche et à l’arrêt, nous
encourageons l’utilisateur à tenter de corriger l’interférence par une ou plusieurs des mesures suivantes:
– réorienter ou déplacer l’antenne de réception;
HDMI
• TV remote pass through cable (× 1)
• Double-sided adhesive tape (× 1)
• FM antenna (× 1)
HDMI Input:
HDMI Output:
Max. Capability:
Output power:
HDMI 1 IN, HDMI 2 IN*
HDMI OUT
1920 × 1080 at 60 Hz
DC 5 V 55 mA
= iPod is not properly connected. Remove iPod from the
unit, and then connect it again.
iPod cannot be charged.
= iPod is not properly connected. Remove iPod from the
unit, and then connect it again. After connecting iPod,
turn on the power again.
* Corresponding to Linear PCM (with sampling frequency
— 32 kHz, 44.1 kHz, 48 kHz)
HDMI
– accroître la séparation entre l’appareil et le récepteur;
– brancher l’appareil dans une prise ou un circuit autre que celui auquel le récepteur est branché;
– consulter un vendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide.
Designs & specifications are subject to change without
notice.
No sound can be heard when HDMI 1 or HDMI 2 source
is selected as a source.
= Check the output settings on the HDMI connected
devices. Set the audio output setting to PCM signal and
enable HDMI Audio Out.
No sound can be heard when TV ARC is selected as a
source.
= Check if your TV supports this function and turn on the
settings for ARC and set the digital audio output setting
to PCM signal on your TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
|