Home Cinema DD Speaker System
Sistema di diffusione DD per Home Cinema
Hembio DD-högtalarsystem
Hjemmebiograf DD-højttalersystem
Kotiteatterin DD-kaiutinjärjestelmä
Heimkino-DD-Lautsprechersystem
Système d’enceinte Home cinéma DD
DD-luidsprekersysteem voor uw huisbioscoop
Sistema de altavoces DD de cine en casa
— Consists of SX-XDS33 and SX-XDC33
SX-XD33
Bestehend aus SX-XDS33 und SX-XDC33
Se compose de SX-XDS33 et SX-XDC33
Bestaat uit SX-XDS33 en SX-XDC33
Consta de SX-XDS33 y SX-XDC33
L’impianto è formato da SX-XDS33 e SX-XDC33
Består av SX-XDS33 och SX-XDC33
Består af SX-XDS33 og SX-XDC33
Sisältää seuraavat osat: SX-XDS33 ja SX-XDC33
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
MANUAL DE INSTRUCCIONES
ISTRUZIONI
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
RUKSANVISNING
VEJLEDNING
KÄYTTÖOHJE
LVT0953-001A
[E]
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the supplied Accessories
Check to be sure you have the following supplied accessories.
The number in parenthesis indicates the quantity of the piece
supplied.
Warnings, Cautions and Others ........................................ 2
Assembly ........................................................................... 4
Additional information ........................................................ 7
Specifications .................................................................... 8
• Speaker cords
Approx. 6 m (3: for satellite speakers placed in front
position and a center speaker)
Approx. 15 m (2: for satellite speakers placed in rear
position)
Warnungen, Vorsichtshinweise usw................................... 9
Zusammenbau ................................................................ 10
Zusätzliche Informationen ............................................... 13
Technische Daten ............................................................ 14
• Screws
(M5 x 12 mm) (4)
(M4 x 25 mm) (12)
Avertissements, précautions et autres ............................ 15
Montage .......................................................................... 16
Informations complémentaires ........................................ 19
Spécifications .................................................................. 20
• Washers
(4)
If any of the items above are missing, contact your dealer
immediately.
Waarschuwingen en andere aandachtspunten ............... 21
Monteren ......................................................................... 22
Extra informatie ............................................................... 25
Specificaties .................................................................... 26
Speaker and Speaker cords—
to improve the sound quality
About DD (Direct Drive) speaker
Advertencias, precauciones y notas................................ 27
Montaje............................................................................ 28
Información adicional....................................................... 31
Especificaciones.............................................................. 32
DD (Direct Drive) technology improves sound localization
and transmits the powerful sounds.
About the OFC cord
The core wires of the supplied speaker cords are made of
OFC (Oxygen Free Copper). This OFC cord enables high
quality sound reproduction.
Avvertenze, Precauzioni e Altro ...................................... 33
Collegamenti ................................................................... 34
Ulteriori informazioni........................................................ 37
Dati caratteristici .............................................................. 38
When connecting the speaker cords
Make sure to match the polarity (ª and ·); otherwise, the
sound will lose the surround effect.
After connecting, check that the exposed cores are fully
inserted into the terminal.
When using other speaker cords
Observe the following;
• Buy thick speaker cords rather than thin cords, and make
them as short as possible for connection.
• Use speaker cords of the same length for both left and
right speakers.
Varningar, försiktighetsåtgärder m.m............................... 39
Montering ........................................................................ 40
Ytterligare information ..................................................... 43
Specifikation .................................................................... 44
• Do not use long speaker cords; otherwise, the sound
quality may deteriorate.
Advarsler, forsigtighedsregler og andet ........................... 45
Samling ........................................................................... 46
Yderligere oplysninger..................................................... 49
Specifikation .................................................................... 50
Varoituksia, huomautuksia ym. ........................................ 51
Kokoaminen..................................................................... 52
Lisätietoja ........................................................................ 55
Tekniset tiedot ................................................................. 56
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Assembling the satellite speakers
2 Join the leg to the stand.
Each speaker (except the center speaker) has been divided into
three parts for shipment. Before using this speaker system,
assemble it first by following the procedure below.
• Rotate either the leg or stand so that the
mark on the
leg and the
direction.
mark on the stand are facing the same
• Make sure to match the screw holes on the leg with those
on the stand so that they are aligned correctly.
mark
Leg
Speaker
section
Leg
Stand
Stand
• Prepare a Phillips screw driver.
Before assembling—
• Take care not to drop the stand while assembling;
otherwise, it may cause damage to the floor or injury.
• Ensure enough space for assembly and installation.
• Place a large, thick cloth on the floor where you
assemble the speaker, so you can protect the floor and
the speaker itself.
mark
3 Fix the leg to the stand with three of the
supplied screws (long: M4 x 25 mm).
• Use the speaker only after assembly is fully and correctly
done.
Leg
Attaching the leg and the stand
Stand
1 Remove the terminal cover from the leg.
First remove the screw on the terminal cover, then detach
the cover by pulling it upward.
• You will need to use the removed screw in step 5 on page
5.
Terminal
cover
Screw
• Do not tighten each screw completely as you put them in
place.
First put all screws in, then tighten them evenly and firmly.
Screw
claws
grooves
It is recommended to place a cushion under the leg.
• You can tighten the screws easily by placing the leg
horizontally.
Leg
Cushion
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3)Insert the speaker cord into the speaker terminal
inside the leg.
4 Connect the speaker cord to the speaker
terminal of the leg
1 Press and hold the clamp.
2 Insert the exposed core of the speaker cord fully
into the terminal.
• Use the 6-meter speaker cords for front speakers and
15-meter speaker cord for rear speakers.
• Each speaker cord has its name tag attached to one end.
Attach the end without the name tag to the speaker
terminal.
• Connect the cord with the black stripe to the ·
terminal.
3 Release your finger.
Tag
1
2
3
To the speaker
terminal of the leg
1)Insert the speaker cord inside the stand as illustrated
below.
• Pull the speaker cord out of the center of the stand by
about 50 cm.
Leg
The cord with the
black stripe is on this
side, facing up.
The cord with
the black stripe.
5 Attach the terminal cover to the leg.
Push cords fully inside the leg. Then fix the terminal cover
using the screw you removed in step 1.
Stand
2)Insert the tips of the speaker cord into the leg and pull
Terminal
cover
them out as illustrated below.
Screw
Leg
claws
grooves
To be continued on the next page
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly (continued)
Joining the leg and the speaker unit
7 Join the speaker section and the leg.
Insert the speaker section to the leg, then fix the speaker
section and the leg with one of the washers and one of the
supplied screws (short: M5 x 12 mm).
6 Insert the speaker cord into the speaker
terminal inside the leg.
1 Press and hold the clamp.
2 Insert the exposed core of the speaker
Speaker
section
cord fully into the terminal.
Joint here
without gap.
• Connect the cord with black stripe to the ·
Push cords fully
inside the leg before
attaching the
terminal.
3 Release your finger.
speaker section.
1
2
3
Screw
Leg
Washer
Repeat the procedure from step 1 to assemble the other
satellite speakers.
Leg
Speaker
section
The cord with
the black stripe.
For disassembly:
Reverse Assembly procedure:
1) Remove the speaker section from the leg.
2) Remove the leg from the stand.
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Connecting the Center speaker
Connecting the speaker system to the amplifier
• To connect the center speaker, use the same type of speaker
cord (6 m; tagged with “FRONT SPEAKER”) as used for
connecting the front speakers.
Before connecting—
• Turn off the power to the amplifier before connecting the
speaker system; otherwise, the speakers may be damaged.
• The impedance of each speaker is 8 Ω. Before connecting
them to your amplifier, check the speaker impedance range of
your amplifier. If the impedance of this speaker is out of the
speaker impedance range indicated on the amplifier, you
cannot connect this system to the amplifier.
• The maximum power handling capacity of the SX-XD33 is
100 W. Excessive input will result in abnormal noise and
possible damage.
• Each speaker cord has its name tag attached to one end.
Attach the end without the name tag to the speaker terminal.
Insert the speaker cord into the speaker
terminal.
1 Press and hold the clamp.
2 Insert the exposed core of the speaker
cord fully into the terminal.
• Be sure to turn down the volume level to prevent unwanted
noise before performing following operations:
– Turning on or off other components,
•
Connect the cord with the black stripe to the ·
terminal.
3 Release your finger.
– Operating the amplifier,
– Tuning FM stations,
– Fast-forwarding a tape,
1
2
– Continuously reproducing high frequency oscillation or high
pitch electronic sounds.
3
• When using a microphone, do not aim it at the speakers or
use it near the speakers; otherwise, the howling which occurs
may damage the speakers.
• Before replacing the cartridge, always turn off the power to the
turntable; otherwise, the clicking noise may damage the
speakers.
Typical connection method to an amplifier
Connect the speakers to a “SPEAKER” terminal of the amplifier
with the speaker cords by referring to the diagram below.
• Make sure to match the polarity (ª and ·) when connecting
the speaker cords.
The cord with the
black stripe.
• The diagram below is an example of a typical connection
method.
Front right
speaker
Front left
speaker
Center speaker
(Approx. 6 m)
(Approx. 6 m)
(Approx. 6 m)
RIGHT
LEFT
RIGHT
LEFT
REAR
FRONT
SPEAKERS
CENTER
SPEAKER
SPEAKERS
Rear right
speaker
Rear left
speaker
Make sure to match the polarity (ª and ·); otherwise, the
sound will lose the surround effect.
After connecting, check that the exposed cores are fully
inserted into the terminal.
CAUTION:
SPEAKER
IMPEDANCE
8
16
Speaker terminals
on the amplifier
(Approx. 15 m)
(Approx. 15 m)
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information (continued)
General layout of speakers
Place all speakers at the same distance from the listening position if possible.
• Usually place the center speaker close to the TV.
• When you place the center speaker on a TV, make sure the surface is level and stable.
Front left
speaker
Front right
speaker
Subwoofer
Center
speaker
Listening position
Rear left
speaker
Rear right
speaker
• For a subwoofer to be used with SX-XD33, it is recommended
to use SX-DW303. This combination gives you the best
possible high quality surround sounds.
Do not lean against the speakers, as the speakers could fall
down or break, possibly causing an injury. Especially be
careful that children do not lean against them.
Specification
SX-XDS33 (Satellite speaker)
SX-XDC33 (Center speaker)
Type :
1-way 2-speaker
Bass reflex type, magnetically
shielded type
Type :
1-way 2-speaker
Bass reflex type, magnetically
shielded type
Speaker unit :
Frequency range :
Input impedance :
Direct drive (9.5 cm × 1 cm) × 2
120 Hz to 20 000 Hz
8 Ω
Speaker unit :
Frequency range :
Input impedance :
5.5 cm cone × 2
80 Hz to 20 000 Hz
8 Ω
Power handling Capacity :
Sound pressure level :
Dimensions (approx.) :
100 W
Power handling Capacity :
Sound pressure level :
Dimensions (approx.) :
100 W
82 dB/W•m
81 dB/W•m
282 mm (width) × 1108 mm
(height) × 282 mm (depth)
3.0 kg each
200 mm (width) × 78 mm
(height) × 120 mm (depth)
0.85 kg
Mass (approx.) :
Mass (approx.) :
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
VICTOR COMPANY OF JAPAN, LIMITED
EN, GE, FR, NL, SP, IT, SW, DA, FI
© 2002 VICTOR COMPANY OF JAPAN, LIMITED
0702NSMMDWJSC
Download from Www.Somanuals.com. All Manuals Search And Download.
|