OUTDOOR DOME CAMERA
INSTRUCTIONS
TK-C2201WPU
(For USA and Canada)
TK-C2201WPE
(For Europe)
For Customer Use:
Enter below the Serial No. which is located on the
body. Retain this information for future reference.
Model No. TK-C2201WPU,TK-C2201WPE
Serial No.
.
LST0979-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing this product.
Before use, please read this "INSTRUCTIONS" and the information materials
included to ensure proper use of this product.
These instructions are for TK-C2201WPU/TK-C2201WPE.
TK-C2201WPE is not evaluated by UL.
Features
v
Easy DAY/NIGHT function (TK-C2201WPU)
v
DAY/NIGHT surveillance with auto IR cut filter on/off (Color/B&W shooting) (TK-
C2201WPE)
v
3D noise reduction (3DNR)
v
4 areas privacy mask
v
Built-in display mode (CRT or LCD selectable)
v
Outdoor-ready vandal and tamper resistant structure (complies with IP66)
How to read this manual
Conventions and symbols
: Indicates operating precautions.
Note
: Indicates reference data regarding limitations on functions, usage
and the like.
Memo
A
: Indicates a reference page or item.
Contents of this manual
v
JVC holds the copyright to this manual. Any part or all of this manual may not
be reproduced without prior consent from the company.
v
Product names of other companies described in this manual are trademarks
or registered trademarks of the respective companies. Symbols such as E, T,
and R are omitted in this manual.
v
Design, specifications and other contents described in this manual are
subject to change for improvements without prior notice.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Operating Precautions
m
Storage and Location of Use
Do not install the camera in the following places.
v
- In a place with vapor or oil, for example in a kitchen.
- When the ambient temperature rises above or falls below the acceptable
range (from -10 f to 50 f)
- In a place at which corrosive gases are emitted.
- Near a source of radiation, X-rays, strong radio waves or magnetism.
- In a place subject to vibration.
- In a place with excessive dirt.
v
Using this unit in the vicinity of the transmitting antenna of a radio or TV,
devices that emit strong electromagnetic waves such as a transformer or motor,
or wireless devices such as a transistor or mobile phone may give rise to noises
in the image and changes in its color.
v
Do not install in an environment where there is cold air or near the air outlet of
an air conditioner. The dome cover may become foggy as a result of sudden
temperature changes.
v
Though this camera is IP66 compliant, there is no guarantee against water
seepage under any circumstances. (IP66 evaluation was not conducted by UL.)
m
Maintenance
v
Clean the dome cover lens using a lens wiper cloth (or a tissue). For tough
stains, wipe with a neutral detergent diluted with water, followed by wiping with
a dry cloth. Do not use benzene or thinner to wipe the camera. Doing so may
melt the surface or cause it to fog.
m
Energy Conservation
When the camera is not in use for a long time, turn off the power for safety and
energy conservation reasons.
v
m
Copyright Protection
With the exception of the user being the copyright holder or when permission
v
such as for duplication has been granted by the copyright holder, permission is
required in principle for the duplication, modification, or transmission of
copyrighted material.
v
Unauthorized duplication, modification, or transmission of copyrighted material
may constitute a copyright infringement, and the user may be liable to
compensate for any damages. When using copyrighted material, be sure to
check the license agreement of the copyrighted material thoroughly.
v
When rights or rights holders are involved with regard to the targeted
duplicating subject, permission may be required for shooting or using
(processing) it. Be sure to check the licensing conditions thoroughly.
4Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
m
Disclaimer
v
We will not be responsible for any inconveniences or disturbances caused in
the event of privacy invasion as a result of camera footages of this product.
m
Others
v
When using this camera with [AGC] set to "MID" or "HIGH", the sensitivity
increases automatically for dark images and the screen may appear grainy, but
this is not a malfunction.
v
If the DAY/NIGHT switch is turned to "AUTO", the mode changes automatically
to black and white in dark places. As the sensitivity level is increased in this
case, the screen may appear grainy and more white spots may appear. When
switching between modes, the brighter area on the screen is emphasized and
visibility may be reduced. However, this is not a malfunction.
v
v
When shooting an extremely bright object (e.g. lamp), the image on the screen
may have white vertical tailings (smear) or expansion (blooming) may appear
around it. This is a characteristic of the CCD and not a malfunction.
When the white balance of this camera is set to "ATW-N" or "ATW-W" and
depending on the conditions of the object, the color tone may differ slightly from
the actual color due to the principle of the automatic tracking white balance
circuit. This is not a malfunction.
v
v
When this camera is used under high temperatures, vertical stripes may appear
on the screen. This is a characteristic of the CCD and not a malfunction.
When this camera is moved from a cold to warm place, condensation may
occur and the camera may not work. In this case, leave the camera under room
temperature for about one hour before turning on the power.
v
v
v
When the power supply voltage is momentarily disrupted or drops due to
lightning, turning on the air-conditioner or the like, image distortion or noise may
occur.
When the power supply voltage of the camera drops, the input protection circuit
inside the camera operates, and the camera may be turned off. Make use of a
voltage rating within 510 % for the camera’s power supply voltage.
This unit enlarges the rotation angle to support wide range set up. When the
zoom of the lens is set to WIDE end and the tilt angle is set around 5807, a part
of this camera appears in the image depending on the rotation angle. In this
v
v
To prevent fogging resulting from temperature changes, be sure to insert the
The 3D noise reduction function of this camera may result in afterimage of a
moving subject. Afterimage is more likely to occur when using the camera with
[DNR LEVEL] set to "HIGH". This is not a malfunction.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Name of Parts
Camera
.
F
G
H
I
J
A
B
K
C
D
E
.
A Mounting Hole 2 2
B Fall Prevention Wire Mounting Screw
C Conduit Plug/Hole (side)
D Dome Cover
E Inner Dome
F Video signal output connector (BNC)
6Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
G Protection Cover
H Power Supply Cable
I Hole for Connecting Cables, Conduit Hole
J Base
K Dome Cover Fastening Screw 23
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Name of Parts (Continued)
Camera (Interior)
The dome cover and inner dome are removed.
.
J
K
M
L
A
B
C
N
O
D
E
P
Q
R
S
F ADJ
F
G
MENU
H
SET
I
MONITOR
.
A Focus Adjustment Ring
B Zoom Adjustment Ring
C Rotation Knob
D Fall Prevention Wire (To prevent the dome cover from dropping)
E Camera Unit Fastening Screw 22
8Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
F Space for Inserting Heater
When mounting the heater (sold separately: KA-ZH215U), read the instruction
manual of the heater before mounting.
G Power Supply Connector for Heater
For connecting to the power supply connector of the heater.
H Tilt Fastening Screw 22
I [MONITOR] Terminal (RCA pin)
J Lug Plate
K Space for Inserting Silica Gel
L Focus Adjust Gear
M Shooting Direction Mark
N Pan Center Mark
O Rotation Center Mark
P Function Selection Switches
Q [MENU] Button
Display the menu screen.
Refer to the attached manual "MENU SETTING" for more details about setting the
menu.
R Status Indication Lamp
Lights up when the power is turned on.
S [J, K, H, I]/[SET] Button
This allows user to select menu screens and change or confirm settings.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
About Connection Cables
The maximum connection distance varies with the type of cable used.
v
Be sure to turn off the power of devices before connecting cables.
.
To video Signal Cable
To Power Supply
.
v
Connect to AC 24 V power supply if using the heater (sold separately:
KA-ZH215U).
Memo
Video signal cable (coaxial cable)
Connect a 75 K coaxial cable (BNC) such as RG-59 to the video signal output
connecter (BNC).
1D0ownload from Www.Somanuals.com. All Manuals Search And Download.
Setup
DC 12 V or AC 24 V power supply cable
Connect the power cord to the DC 12 V or the AC 24 V power supply.
The unit is to be powered by a UL Listed Class 2 power supply only. (For USA
and Canada)
The AC 24 V and DC 12 V power supply shall conform to the following:
UL Listed Class 2 power supply only,
Class 2 not wet and Class 3 wet wiring (For USA)
Isolated power supply only (For Europe)
This installation shall be in accordance with the National Electrical Code, ANSI/
NFPA 70.
The following table shows the connection distances when 2-core VVF (vinyl-
insulated vinyl sheath cables) are used. (Reference value)
Conductor
diameter
Maximum
Maximum
Maximum
connection
connection
connection
distance: DC 12 V
(not using heater)
distance: AC 24 V distance: AC 24 V
(not using heater)
(using heater)
Φ 1.0 mm
50 m (160 ft)
140 m (450 ft)
220 m (720 ft)
130 m (420 ft)
40 m (130 ft)
(AWG 18)
Φ 1.6 mm
(AWG 14)
350 m (1100 ft)
550 m (1800 ft)
120 m (390 ft)
180 m (590 ft)
Φ 2.0 mm
(AWG 12)
v
If thin cables are used, the resistance of the cables will be high and a
significant voltage drop will occur when the camera is at its maximum
power consumption. Either use a thick cable with low resistance or
place the power supply near to the camera and shorten the length of
the cable to restrict the voltage drop at the rated current of camera to
below 10 %. If voltage drop occurs during operation, the performance
will be unstable.
Note
v
Do not connect the AC 24 V cable to commercial power supply. If it is
connected by mistake, the internal circuit may be damaged. Do not
use the camera and make sure to send it to the nearest JVC dealer for
inspection.
v
v
Do not connect DC 12 V and AC 24 V cables at the same time.
When connecting the DC 12 V cables, ensure that the polarities are
correct.
Color of the cables red: +12 V, black: GND
v
When using a DC 12 V power supply, ensure that the polarities of the
cable are correct.
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.1
Setup
Setting the Switches
Before mounting the camera, set the function setting switches on the camera.
To set the switches, use a fine-tipped screwdriver.
.
DIP Switch
Settings Chart
1
D/N
OFF
AUTO
2
3
4
BLC
OFF ON
MONITOR
TYPE
LCD
-
CRT
-
NOT UESD
Function selection switches
.
1
[D/N AUTO/OFF] Day & Night Switch
Set this to "AUTO" when shooting a subject with continually changing brightness
(day/night). The image switches to color when the subject is bright, and black and
white when it is dark. The image is set to color at all times when "OFF" is selected.
(Default setting: AUTO)
You can set the image to black and white at all times using the menu.
(TK-C2201WPE only)
Memo
2
[BLC OFF/ON] Backlight Compensation Selector Switch
Set this to "ON" when shooting in backlight. The subject becomes easier to see as
brightness is adjusted according to the photometry area set in [BLC AREA] of the
menu.
(Default setting: OFF)
Refer to [BLC AREA] in the "MENU SETTING" (separate).
Memo
3
[MONITOR TYPE LCD/CRT] Monitor Type Selector Switch
Set this to "LCD" or "CRT" according to the monitor in use.
(Default setting: LCD)
Refer to [LCD TYPE] in the "MENU SETTING" (separate).
Memo
1D2ownload from Www.Somanuals.com. All Manuals Search And Download.
Installation
Mounting the Camera
Selecting a mounting method
v
v
Mounting the Camera Using the Conduit Hole at the Bottom of the Base
v
v
Mounting the Camera Using the Conduit Hole at the Side of the Base
When mounting the camera to the ceiling, ensure to wear safety glasses
to protect the eye from any falling objects.
Memo
Mounting the camera directly to the ceiling or on the wall
When mounting to a wall, replace areas indicated as "ceiling" in the procedures by
"wall".
m
Preparing the camera
1
2
Remove the dome cover (screws x3)
Remove the inner dome from the catches (two locations)
The inner dome can be easily removed by turning it about 45 degree and grip
from both sides near the catches as illustrated in the diagram.
.
Doom cover
1
Wrench (supplied)
Inner dome
2
Catches ( 2)
Fall prevention
wire
.
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.3
Installation
Mounting the Camera (Continued)
m
Mounting the Camera Unit
1
2
Make a hole (Φ30 mm) in the ceiling using the template provided
Mount the fall prevention wire for connecting the camera unit to
the ceiling
The fall prevention wire is not provided. Prepare a wire, taking into due
consideration the length, strength, pull and material (insulating).
① Remove the fall prevention wire fastening screw on the bottom of the camera
unit to mount the fall prevention wire.
② Mount the fall prevention wire at a structurally strong location.
3
Mount the camera unit to the ceiling
Pull the cables from the ceiling and camera towards the lens as illustrated in the
diagram, align the (ñ) mark to the shooting direction and mount the camera to the
ceiling. Align the (ñ) mark upwards when mounting the camera on the wall.
.
30 mm
1
Fall prevention wire (not supplied)
Camera unit
Fall prevention wire
2
8 mm
2 mm
6 mm
and below
12 mm
and below
Shooting direction
mark
4.1
6.5 mm
3
4 mm 2 (not supplied)
The screws for mounting the camera are not provided. Use a suitable
type of screws according to the material of the mounting location.
Note
1D4ownload from Www.Somanuals.com. All Manuals Search And Download.
Installation
m
Connecting the cable
For safety reasons, turn on the power only after all the connection is complete.
The status indicator lights up when the camera is turned on.
1
Lower the protection cover and connect the connectors.
Upon connecting, restore the protection cover to cover the connectors. This will
isolate and protect the metallic parts of the connectors.
2
3
Wrap insulation tapes around the connecting parts of the power
supply cables
Wrapping insulation tapes will improve future work conditions, as well as
reduce penetration by noise and other objects.
Memo
4
5
Wrap the insulation tape
Push the connector of the connected coaxial cable back to the
ceiling.
.
3
Solder or caulk
2
Insulating tape
1
Bind insulating tape
4
Protection
cover
Power supply cable
Coaxial
cable
.
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.5
Installation
Mounting the Camera (Continued)
m
Process after connection
Fill the conduit hole and mounting holes with sealing agent and insert the silica
gel.
1
Fill the conduit hole and the screw mounted holes (2 locations)
with sealing agent (GE silicon)
Seal the holes completely. Failure to do so may cause water or moisture
to enter, thereby fogging the lens and dome cover.
Note
2
Remove the silica gel (provided) from its bag and insert in the
position as shown in the diagram
.
1
2
Sealing material
Lug plate
Secure the silica
gel with the lug
plate such that
it will not drop.
*
This illustration is
for the purpose of
explanation.
The camera unit
is not shown here.
*
Silica gel
Silica gel insertion
space
.
v
When mounting the camera under raining conditions, make sure that
rain does not enter into the camera.
Note
v
v
Be sure to use the silica gel provided. Failure to do so may fog up the
camera lens and dome cover.
If you are not adjusting the camera angle soon after mounting the
camera, insert the silica gel (provided) only after adjustment.
Prolonged exposure to air will make the silica gel (provided) less
effective.
1D6ownload from Www.Somanuals.com. All Manuals Search And Download.
Installation
m
Adjusting images
After mounting is completed, adjust the images while checking the actual image.
m
Mounting the Dome Cover
Attach the dome cover back when all settings are finished.
1
Mount the inner dome
Mount the inner dome in a way that supports the tilt direction of the lens.
Insert the inner depression of the inner dome into the protruding parts beside the
fastening screw. Push it in until it is fixed by the catches (2 locations).
.
Protruding part
Catches ( 2)
Inner depression
Inner dome
.
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.7
Installation
Mounting the Camera (Continued)
2
Mount the dome cover
① Clean the dust and dirt on the dome cover.
② Align the position marks (3 locations) on the camera unit and dome cover,
followed by pressing in directly to mount the cover.
③ Tighten the dome cover fastening screw.
.
Position alignment
mark (x 3)
Dome cover
Dome cover protective sheet
.
v
Ensure that the silica gel (provided) has been inserted before mounting
the dome cover.
Note
v
v
v
Be sure to secure the dome cover firmly. If it is not firmly secured, the
cover can drop or the humidity inside the camera can increase and fog
up the interior of the cover.
When the cover is removed again after mounting the dome cover, the
field angle may changed. If the field angle is changed, re-adjust the
focus and the field angle.
Ensure that the fall prevention wire of the dome cover is not caught
between the dome cover and the base. Failure to do so may prevent
the dustproof and waterproof functions from working properly.
1D8ownload from Www.Somanuals.com. All Manuals Search And Download.
Installation
Mounting the Camera Using the Conduit Hole at the Bottom of the
Base
Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE)
1
2
Remove the camera unit from the base and mount the fall
prevention wire to the camera unit
① Loosen the camera unit fastening screw (2 locations) with a screwdriver.
② Press the catch (2 locations) inwards and remove the camera from the base.
③ Remove the fall prevention wire fastening screw on the base to mount the fall
prevention wire. (The fall prevention wire is not provided.)
1
2
2
Catches (x 2)
1
1
2
RELEASE
Camera unit
Base
.
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.9
Installation
Mounting the Camera (Continued)
3
Wind the sealing tape
Wind the sealing tape around the pipe junction (where the conduit hole thread
lines with the pipe screw hole) two or more times.
4
Mount the base to the pipe
Turn and screw the base unit to the pipe in the clockwise direction.
When screwing the pipe, do not screw beyond 12 mm. Doing so can
damage the camera interior.
Note
5
Secure the base unit to the ceiling
Use the M4 screw (x2) to secure the base firmly to the ceiling.
v
Make sure there is no gap between the ceiling and the base.
The M4 screws are not provided. Use a suitable type of screws
according to the material of the mounting location.
Note
v
6
Mount the fall prevention wire to a structurally strong location
12 mm and below
3
Sealing tape
Fall prevention wire
8mm
2mm
M4 mm screw
.
7
Push the connector of the connected coaxial cable back to the pipe.
8
Mount the camera unit to the base
① Push in until the catch (2 locations) snaps on.
Make sure that the cables and the fall prevention cable are not caught
between the camera and the base during mounting.
Note
② Fasten the camera unit fastening screw (2 locations) to secure the camera.
9
The procedures for the following are the same as that for normal
camera mounting
2D0ownload from Www.Somanuals.com. All Manuals Search And Download.
Installation
Mounting the Camera Using the Conduit Hole at the Side of the
Base
If the camera cannot be mounted directly to the ceiling, use the conduit hole at the
side of the base to mount the camera to the pipe.
Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE)
1
2
Remove the camera unit from the base and mount the fall
prevention wire to the camera unit
3
Wind the sealing tape
Wind the sealing tape around the pipe junction (where the conduit hole thread
lines with the pipe screw hole) two or more times.
4
Remove the conduit plug from the base
Loosen the mounting screw (M3 x 6 mm) using a flathead screwdriver and remove
the conduit plug at the side of the base.
5
Mount the conduit plug that was removed to the conduit hole at
the bottom of the base
6
Mount the base to the pipe
Screw the pipe to the conduit hole at the side of the base.
When screwing the pipe, do not screw beyond 12 mm. Doing so can
damage the camera interior.
Note
Conduit plug
3
Sealing tape
Mounting screw
.
7
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.1
Installation
Mounting the Camera (Continued)
Mounting the Camera using the Electrical Box
1
2
Mount the camera unit to the electrical box
Mount the camera unit to the electrical box using the mounting hole (2 locations)
with the M4 screw (2 pieces).
The screws are not provided.
Memo
.
4 Inch square
electrical box
M4 Screw
.
3
The procedures for the following are the same as that for normal
camera mounting.
2D2ownload from Www.Somanuals.com. All Manuals Search And Download.
Adjustment
Adjusting Image
After mounting the camera, adjust the images while looking at the actual image.
Discharge the static electricity from your body by touching the metallic part of the
monitor terminal before handling the camera as static electricity may cause the
camera to malfunction.
1
Mount the monitor
Connect the monitor terminal of this camera to a monitor to adjust the camera’s
shooting direction, image and focus.
2
Turn on the camera
.
.
Monitor terminal
75
terminal
Monitor
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.3
Adjustment
Adjusting Image (Continued)
3
Adjust the shooting direction of the camera
Adjust the camera for pan, tilt and rotation, and face the camera towards the
subject.
Pan: 175
Tilt fastening screw
Tilt: 80
Rotation: 100
Shooting direction
mark
Pan center mark
Rotation center mark
Rotation knob ( 2)
.
v
Rotate both pan 5175 7 and rotation 5100 7 from the positions
aligned with the camera’s shooting direction mark, pan center mark
and rotation center mark. Be sure to hold the rotation knob and adjust
the rotation without holding the lens unit.
Loosen the tilt fastening screw before performing tilt adjustment.
After adjusting the field angle, tighten and secure the tilt fastening
screw so that the field angle will not be misaligned.
Moving the camera beyond its adjustable range may deteriorate the
performance of this camera.
As this camera has a wide tilt/rotation range, a part of this camera may
appear on the screen depending on the field angle and direction.
Do not hold the lens unit when adjusting the camera direction.
Applying force on the lens unit may damage it.
Memo
Note
v
v
v
v
v
2D4ownload from Www.Somanuals.com. All Manuals Search And Download.
Adjustment
4
Adjust the image size
Loosen the fastening screw for the zoom adjustment ring and move the ring to the
left/right to adjust the image size. After adjustment is complete, fasten the screw.
5
Adjust the focus
① Hold the focus adjust gear knob, shift the catch from point A to point B as
illustrated in the diagram to disengage the gear.
To prevent the gear shaft from breaking when the gear is opened too
far out from B, remove the gear shaft from the bearing (C in diagram).
In this case, re-insert the shaft back into the bearing C and return it to
the original position before using.
Note
② Loosen the fastening screw for the focus adjustment ring and move the ring
to the left/right to adjust the focus.
.
Focus adjustment ring
Knob
Catch
B
A
Zoom adjustment ring
C
Focus adjust gear
.
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.5
Adjustment
Adjusting Image (Continued)
6
Fine adjust the focus
① Press and hold the [J] button.
v
Focus adjust mode will be activated and "FOCUS ADJUST MODE" is
displayed on the monitor screen.
v
The contours are emphasized as the iris opens and the depth of field
becomes shallow.
v
After adjustment, press [ K, H, I]/[SET]/[MENU] to exit focus adjust mode.
The mode is also automatically deactivated after about 30 seconds.
v
During the focus adjust mode, the electronic shutter will function
automatically. As a result the screen will appear grainy. This is not a
malfunction.
Memo
② Shoot the subject.
③ Return the catch to A in the diagram, and then rotate the knob to adjust the
focus to the optimum position.
④ Rotate the focus adjust gear knob one base pitch in the direction of the arrow
in the diagram to correct the focus shift when mounting the dome cover.
⑤ Peel off the protection sheet temporarily and cover the dome cover to check
the focus. After checking, paste the protection sheet back on the dome
cover.
.
Catch
Knob
A
One base pitch
.
2D6ownload from Www.Somanuals.com. All Manuals Search And Download.
Adjustment
7
Tighten the fastening screw of the focus adjustment ring
Hold and press the focus adjust gear between your fingers in the direction of the
arrows in the diagram, and tighten the fastening screw of the focus adjustment
ring.
.
Focus adjustment ring
.
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.7
Adjustment
Adjusting the Auto White Balance
Each light source has its own color temperature. Therefore, when the main light
source lighting the subject is changed, adjust the white balance again.
1
2
Press the [MENU] button.
Select [WHITE BALANCE] with the [J/K] button and "AWC" with
the [H/I] button, then press the [SET] button.
3
Zoom in to fill the screen with white.
Place a white object at the center of the screen, under the same lighting condition
as the subject to be shot and zoom in to fill the screen with white.
4
Press the [SET] button.
Auto white balance adjustment begins. During operation, "AWC OPERATION" is
displayed on the screen.
5
Adjustment is complete.
When the appropriate white balance is acquired, "AWC OK" is displayed.
MENU button
SET button
WHITE BALANCE CONTROL
AWC SET
WHITE BALANCE CONTROL
AWC SET
E
E
160
160
160
160
F ADJ
R GAIN
B GAIN
R GAIN
B GAIN
1
MENU
SET
AWC OK
AWC OPERATION
button
AWC OK
(adjustment completed)
AWC OPERATION
(during operation)
.
m
Error display
If auto white balance adjustment is not successful, the following messages will
appear on the monitor.
AWC ERROR : NG (Subject error)
Displayed when there is not enough white color on the subject or the color
temperature is not suitable.
Fill the screen with a white object thoroughly and adjust the white balance again.
AWC ERROR : LOW LIGHT (Insufficient Illumination)
Displayed when the light is low. Increase the illumination, then readjust the white
balance.
AWC ERROR : HIGH LIGHT (Excessive Illumination)
Displayed when the light is too bright. Decrease the illumination, then readjust the
white balance.
AWC ERROR : TIME OVER (Subject movement)
Displayed when the subject moves. Keep the subject still, then readjust the white
balance.
2D8ownload from Www.Somanuals.com. All Manuals Search And Download.
Others
Specifications
Horizontal
resolution
: 550TV lines (typical)
Video S/N ratio : 52 dB (typical, AGC OFF)
Minimum
illumination
: Color mode:
0.05 lx (typical, 50 %, F1.2, AGC HIGH)
Black and White mode:
0.03 lx (TK-C2201WPU) (typical, 50 %, F1.2, AGC HIGH)
0.006 lx (TK-C2201WPE) (typical, 50 %, F1.2, AGC HIGH)
Zoom ratio
: 3.75
Focal length
: 2.8 mm to 10.5 mm
: F 1.2 (f = 2.8 mm) F 2.7 (f = 10.5 mm)
Maximum
aperture ratio
Minimum
aperture
: Equivalent to F 360
Angle of view
: f = 2.8 mm
99.5 7 (H) 2 73.2 7 (V)
f = 10.5 mm
27.4 7 (H) 2 20.6 7 (V)
Angle adjustment : Pan: 5175 7
range
Tilt: 580 7
Rotation: 5100 7
Power supply
: AC 24 V 60 Hz, DC 12 V UL Listed Class 2 power supply only
(TK-C2201WPU)
AC 24 V 50 Hz/60 Hz, DC 12 V (TK-C2201WPE)
Power/current
consumption
: 2.3 W (TK-C2201WPU)
220 mA (TK-C2201WPE)
when using heater (KA-ZH215U):
20 W (TK-C2201WPU)
1 A (TK-C2201WPE)
Mass
: approx. 1.3 kg
Ambient
temperature
: -10 f to 50 f (14 g to 122 g) (Operation)
0 f to 40 f (32 g to 104 g) (Recommended)
when using heater (KA-ZH215U):
-30 f to 50 f (-22 g to 122 g) (Operation)
-20 f to 40 f (-4 g to 104 g) (Recommended)
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.9
Others
Specifications (Continued)
Accessories
: (TK-C2201WPU)
WARRANTY CARD 2 1
INSTRUCTIONS 2 3
Silica gel 2 1
Wrench 21
Template 2 1
(TK-C2201WPE)
INSTRUCTIONS 2 5
Silica gel 2 1
Wrench 21
Template 2 1
3D0ownload from Www.Somanuals.com. All Manuals Search And Download.
Others
m
External dimensions [Unit: mm (inch)]
.
121(4-3/4)
113(4-1/2)
9
(3/8)
Screw for conduit
(bottom surface, side surface)
(TK-C2201WPU: G3/4-14 UNC,
TK-C2201WPE: M25)
160(6-1/4)
.
* Specifications and appearance of this camera are subject to change for
improvements without notice.
Download from Www.Somanuals.com. All Manuals Search And Downloa3d.1
Q 2009 Victor Company of Japan, Limited
LST0979-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
|
