IP CAMERA
INSTRUCTIONS
(Setting)
VN-V25U
VN-V26U
VN-X35U
VN-V225U series
VN-X235U series
Thank you for purchasing this JVC product.
Before operating this unit, please read the
instructions carefully to ensure the best
possible performance.
LST0886-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
Ⅵ VFS(Variable File Size)
Network Requirements
(TX) is applicable to VN-X series only.
Distribution File Size
●
Ensure that there is sufficient network
bandwidth for the data volume to be sent out
by camera. Do not send multicast stream that
exceeds the bandwidth. If the entire bandwidth
is used by the multicast stream, control of this
camera via the network may fail.
Data volume to be sent by camera varies with
the settings and number of distributions.
The maximum bit rate for transmission is
about 20 Mbps.
(typical sizes)
Quad
(TX)
VGA
QVGA
Setting 1 (High)
180 KB 80 KB
160 KB 60 KB
140 KB 40 KB
120 KB 30 KB
27 KB
20 KB
13 KB
10 KB
Values
●
●
2
for
Picture
Quality
3
4
(Medium)
Estimation of Total Bit Rate
5
100 KB 25 KB
8 KB
7 KB
5 KB
The total JPEG bit rate from camera is
determined by the camera settings, number of
clients, and the client’s requested number of
frames. The total MPEG4 bit rate from camera is
determined by the number of distributions.
Develop a design upon taking the above into
consideration.
6
80 KB
60 KB
20 KB
15 KB
7 (Low)
The maximum number of distributions varies with
the bit rate settings as well as the client’s
requested frame rate. Up to 20 streams can be
distributed (including multicast). The total frame
rate refers to the sum of these frame rates.
For example, when 10 fps is requested by two
clients, and in addition, multicast is transmitted
at a rate of 10 fps, the total frame rate will be:
Bit Rate of JPEG Stream
The JPEG file size per frame varies with the
encoding settings as well as input video signals.
The following table shows typical sizes. When
VFS is selected, the quantization table during
JPEG encoding will be maintained, and the file
size will increase/decrease according to the input
signals. When AFS is selected, encoding will be
performed such that the target file size is the
average size of multiple JPEG images.
10 + 10 + 10 = 30 fps
For example, when 5 fps is requested by two
clients, and in addition, multicast is transmitted
at a rate of 5 fps, the total frame rate will be:
5 + 5 + 5 = 15fps
Ⅵ AFS (Average File Size)
If JPEG file size per piece is 120KB, total bit rate will be:
120KB
ן 15fps = 1800KB/s = 14.4Mbps (TX) is applicable to VN-X series only.
Selectable Range for Distribution File Size
Bit Rate of MPEG4 Stream
Quad
VGA(TX)
You can select either the Variable Bit Rate (VBR)
or Constant Bit Rate (CBR) system for MPEG4
stream.
VGA
QVGA
40 KB to
200 KB
10 KB to
100 KB
3 KB to 33 KB
When the VBR system is selected, the bit rate
varies according to the condition of the input video
signals. The VBR system delivers a stable picture
quality, but forecast of the bit rate is difficult.
When the CBR system is selected, encoding is
performed at a fixed bit rate regardless of the
condition of the input video signals. The picture
quality varies under the CBR system, but the bit
rate can be easily forecasted.
You can specify an estimated bit rate for both
VBR and CBR. (64 kbps to 8000 kbps)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
● When both JPEG and MPEG4 images are distributed
Network Requirements
(continued)
When both JPEG and MPEG4 images are distributed
simultaneously, distribution up to two clients for JPEG
and three clients for MPEG4 respectively is possible.
However, distribution requests that exceed a total bit rate
of 20 Mbps will be denied.
Maximum number of distributions when JPEG and
MPEG4 data is distributed
Bit Rate of Audio
Only 1 audio data stream can be received. Data volume
for 1 audio stream is 64 kbps. Audio data volume may be
calculated using the following formula.
Maximum number
of distributions
for JPEG
Maximum number
of distributions for
MPEG4
Total bit rate
64 kbps x no. of streams
The number of streams is the total number of streams
sent via TCP (number of clients), streams sent via
multicast, and stream received by camera
(Example) When camera sends out 2 audio streams and
receives 1 audio stream, data volume will be as follows.
64 kbps x 3 = 192 kbps
2
3
20 Mbps and
below
●
When only MPEG4 images are distributed
The maximum number of distributions is determined by
the preset bit rate. When a distribution request that
exceeds the maximum number of distributions is
received, this request is denied.
Restrictions on the Number of
Distributions for camera
T
he maximum number of distributions for camera is
When distributing only MPEG4 data
determined by the settings as well as requirements
from the client.
Maximum
Preset bit
rate
Total maximum
bit rate
number of
For JPEG distribution, you can select either “Frame Rate
distributions
Priority” mode or “Client number Priority” mode. “Frame
Rate Priority” mode distributes JPEG images according
to the frame rate requested by the client. The maximum
number of distributions is determined based on the
highest bit rate within the distribution streams. For “Client
number Priority” mode, if there are requests from multiple
clients, JPEG images are distributed in a lower frame rate
than that requested to cater to multiple clients. It can
accept 20 distribution requests as the maximum number
of clients.
0.6 Mbps and 20
below
12 Mbps
12 Mbps
12 Mbps
12 Mbps
3 Mbps and
below
4
3
2
1
4 Mbps and
below
6 Mbps and
below
Ⅵ
When Frame Rate Priority Mode is Selected
Larger than
6 Mbps
Maximum
configurablevalue
(8 Mbps)
JPEG images are distributed at the frame rate requested
by the client.
When a distribution request that exceeds the maximum
number of distributions is received, this request is denied.
Ⅵ
●
When Client number Priority Mode is Selected
When only JPEG images are distributed
●
When only JPEG images are distributed
For example, if Client A requests for JPEG at 1 Mbps,
while Client B requests for JPEG at 5 Mbps, additional 2
streams (total 4 streams) of distribution are possible for
request below 5 Mbps.
If the distribution request would be accepted in the frame
rate priority mode, distribution works in the same way as
frame rate priority mode, where JPEG images are
distributed at the frame rate requested by the client. If the
distribution request would be denied in the frame rate
priority mode, the frame rate is controlled such that the
maximum bit rate is as shown in the following table, to
accept distribution requests from up to 20 clients. For
example, if Client A and B request for JPEG at 10 Mbps,
and Client C requests for JPEG at 5 Mbps, the frame rate
will be reduced such that the distribution bit rate to each
client is less than 5 Mbps.
Maximum number of distributions when only
JPEG data is distributed
Distribution
atmaximum
bit rate
Maximum
number of
distributions
Total
maximum bit
rate
1 Mbps and
below
20
4
20 Mbps
20 Mbps
20 Mbps
Maximum bit rate when only JPEG data is
distribute
d
5 Mbps and
below
Current number of
distributions
Maximum bit rate
Total maximum bit
rate
10 Mbps and
below
2
2 and below
3 to 4
10 Mbps
5 Mbps
1 Mbps
20 Mbps
20 Mbps
20 Mbps
Larger than
10 Mbps
1
Maximum
configurable
value
5 to 20
(24 Mbps)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
●
When both JPEG and MPEG4 images are distributed
When both JPEG and MPEG4 images are distributed,
distribution works in the same way as frame rate priority
mode if the distribution request would be accepted in the
frame rate priority mode. If the distribution request would
be denied in the frame rate priority mode, the frame rate
is controlled such that the maximum bit rate is as shown
in the following table, to accept distribution requests for
up to a total number of 20 JPEG and MPEG distributions.
However, distribution requests for which the total bit rate
of the MPEG4 distribution stream exceeds 10 Mbps will
be denied.
Packet Loss
When acquiring images from camera via TCP,
packet loss may be recovered by TCP
transmission. When there is considerable delay
in the network, however, missing data may occur
and the image frame rate may drop. In the case
of MPEG4, noise interference may occur and
playback may fail.
Audio may be interrupted.
When packet loss occurs during multicast
sending from camera, the image frame rate may
drop. In the case of MPEG4, noise interference
may occur and playback may fail.
Maximum JPEG bit rate when only JPEG and MPEG4
data is distributed
Current number
of distributions
Maximum bit rate Total maximum
Audio may be interrupted.
bit rate
List of Protocols and Port Numbers
Used by camera
2 and below
3 to 4
5 Mbps
10 Mbps
10 Mbps
10 Mbps
2.5 Mbps
0.5 Mbps
camera uses the protocols and port numbers
listed below. Ensure that these ports are allowed
through the firewall when a firewall is to be
installed.
5 to 20
When only MPEG4 images are distributed, the maximum
number of distributions is determined by the preset bit
rate. When a distribution request that exceeds the
maximum number of distributions is received, this
request is denied.
When distributing only MPEG4 data (
Memo:
● If the bit rate is changed when image
distribution is in progress, the restriction on
distribution may not work correctly.
Protocol/Port No.
Source
Purpose of Use
A
Page 4)
TCP/80
JPEG/MPEG4
acquisition, Web
Settings page, API,
Sending/Acquisition
of sound
TCP/5510
UDP/5510
UDP/9541
VSIP
VSIP
Insufficient network bandwidth
When there is insufficient bandwidth, the number
of JPEG frames (frame rate) that the client can
acquire will decrease. Delay will also occur in the
distribution of images. In the case of MPEG4,
noise interference may occur and playback may
fail. There may be a longer delay or interruption
in the audio.
VSIP discovery
protocol
TCP/10020
TCP/10021
TCP/10023
(Reserved for
adjustment)
Network Delay
TCP/32040
TCP/49298
Destination
TCP/20, 21
TCP/25
Alarm server
When the client acquires JPEG via TCP, camera
will send out data while checking the ACK from
the client at the same time. For networks with
considerable delay, data cannot be sent out until
ACK is received, and therefore the frame rate
will drop. In the case of MPEG4, noise
interference may occur and playback may fail.
Audio may be interrupted.
Sound data reception
FTP
Mail delivery
POP (Mail Delivery)
Decrease in the frame rate due to network delays
can be eliminated by receiving data via multicast.
TCP/110
TCP/User Setting No. Sending alarm
UDP/123 SNTP
UDP/User Setting No. Sending alarm
Network Jitter
When there is considerable network jitter, delay
time may be prolonged and the image frame rate
may drop. In the case of MPEG4, noise
interference may occur and playback may fail.
Audio may be interrupted.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
address.
● Minimum computer specifications for
setting
OS
: Windows XP (Professional or
Home Edition) (SP2)
IP address setting procedure
Web browser
: Internet Explorer Version 6.0
XP : Version 6.0
Vista : Version 7.0
Follow the procedure below to configure the IP
address of the camera.
Step1 IP address setting at the
computer
Note:
(APage 7)
● When setting the IP address of the camera,
do so by using a network that is made up of
only the camera, the computer for setting and
the switching hub.
Set the IP address of the computer for
configuring the camera settings.
G
devices or networks via a LAN cable for
setting can cause problems.
(APage 8)
Configure the Internet Explorer settings in
order to establish connection between the
computer and the camera.
ⅷ System configuration required for setting
IP address
Camera at factory default is set to ADHCP
activate under the following IP address after
startup. Set the computer to an IP address that
enables communication with the following. (For
example, set the IP address to 192.168.0.100
and subnet mask to 255.255.255.0.)
G
Step3 Connecting the camera to the
computer
(APage 10)
Connect the computer and the camera.
IP address
: 192.168.0.2
Subnet mask
: 255.255.255.0
G
Default gateway : None
Memo:
Step4 IP address setting for the camera
● To set a static IP address for the camera,
connect the camera, the switching hub and
the computer for setting using a straight LAN
cable of Category 5 and above.
(APage 12)
Set the [IP Setting] item on the [Basic
Settings1] screen to ADHCP DisableBor
ADHCP EnableB.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IP address setting at the computer
Set the computer to an IP address that enables communication with the camera.
Procedures described in this item are intended for Windows XP users.
1.Click [Start]
● Select in the sequence of [Control Panel]-[Network Connection]-[Local Area].
Windows Vista :
● Select in the sequence of [Settings]-[Control Panel]-[Network and Sharing Center]-[Manage
network connections].
2.The computer on which Internet Explorer is launched automatically selects the connected
network
● Right-click and select [Properties].
● Check to ensure that the [Client for Microsoft Networks] and [Internet Protocol(TCP/IP)] check
boxes are selected.
Windows Vista :
● Check to ensure that the [Microsoft Network Client] and [Internet Protocol Version 4 (TCP/IPv4)]
checkboxes are selected.
3.Select [Internet Protocol(TCP/IP)] and click [Properties]
Windows Vista：Select [Internet Protocol Version 4 (TCP/IPv4)], and click [Properties]
4.Set the IP address
Select [Use the following IP address].
A
B
Specify the [IP address]. (For example,
use 192.168.0.100)
Memo:
Make sure that you take note of the
original IP address before altering.
Note:
Ensure that a duplicate IP address is
not specified within the same network
environment.
Set [Subnet Mask] to a value that is
appropriate for the setting operation.
Consult the network administrator if you
have any queries. (Use 255.255.255.0 when
the camera is in its default settings.)
C
When a [Default Gateway] is present,
make use of the corresponding IP
address (e.g., 192.168.0.254).
Click
D
E
5.Click [OK] on the ALocal Area Connection PropertiesB screen
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
IP Address Settings
(continued)
Internet Explorer Setting
1.Launch the Internet Explorer on the computer
2.When proxy settings are enabled in the Internet Explorer, follow the steps below to disable
the proxy of the Internet Explorer
● Select in the order of [Tool]-[Internet Options]-[Connections]-[LAN Setting], followed by
deselecting the check for [Use a proxy server for your LAN] under [Proxy Server] of the [Local
Area Network (LAN) Settings] window.
Deselect the check
3. If the active script of the Internet Explorer is disabled, follow the steps below to enable it
● Select [Trusted sites] under [Tool]-[Internet Options]-[Security]. Upon doing so, the [Sites…]
button directly below becomes active. Click this button and deselect the check in the displayed
window, and add the following web site to the zone.
● Next, select [Trusted sites] under [Tool]-[Internet Options]-[Security], and press the [Custom
Level] button. Select [Enable] under [Scripting]-[Alarm] of the [Security Settings] window that
has been opened.
Select [Enable]
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4.If ActiveX controls and plug-ins of the Internet Explorer is disabled, follow the steps below to
enable it
● Click [Trusted sites] under [Tool]-[Internet Options]-[Security]. Select the [Custom Level] button
and open the [Security Settings] window. Set all items under [ActiveX controls and plug-ins] in
the opened window to [Enable]. Enable also [Allow Script-initiated window without size or
position constraints.] under [Miscellaneous].
Select [Enable]
5.Disable pop-up block
Connection of camera cannot be established when pop-up block in the Internet Explorer is set to
AEnableB.
Follow the steps below to set the pop-up block to AdisableB.
● Selecting [Tool]-[Pop-up Blocker]-[Turn Off Pop-up Blocker] permits all sites.
● To allow only specific sites such as camera, select [Tool]-[Pop-up Blocker]-[Turn On Pop-up
Blocker], followed by selecting [Tool]-[Pop-up Blocker]-[Pop-up Blocker Settings] that becomes
active to open the [Pop-up Blocker Settings] window.
In the opened window, add the address of camera as a permitted web site address.
6.When plug-in tools such as the Yahoo or Google toolbar are included in the Internet
Explorer, disable the pop-up block function of these plug-in tools as well
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
IP Address Settings
(continued)
Connecting the camera to the computer
1.Launch the Internet Explorer
Click [Go].
Enter the following IP address into the address field.
B
A
Memo:
● If the proxy server settings for access to the Internet via the Internet Explorer is enabled, you may
not be able to specify the IP address directly. In this case, change the proxy settings of the Internet
Explorer.
Ⅵ When the IP address of the camera is unknown
IP address settings cannot be changed by accessing via a computer when the IP address of the
camera is unknown. You can use the following method to identify the IP address.
● Search for the camera in the LAN using [Search tool] inside [Tool_E] folder of the supplied CD-
ROM.
T For details on [Search tool], please refer to the AReadmeBfile in the CD-ROM supplied with this
product.
2.Enter the user name and password (login as administrator) (A Page 14)
Enter the user name.
A
B
This is set to AadminBby default.
Enter the password.
This is set to AjvcBby default.
Click [OK].
C
Memo:
● After the [Security Settings] screen appears, press the [OK] button to proceed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3.Built-in Viewer of camera is displayed
4.The operator password entry screen appears
A
B
A Enter the password (default is AjvcB) of AoperatorBauthority.
B Click [OK].
Memo:
● The operator password entry screen does not appear if the password is stored on the computer.
Proceed to configure the IP address setting for the camera. (A Page 12)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
IP Address Settings
(continued)
IP address setting for the camera
1 Click [Details] of the camera Built-in viewer
Click
2 The [Basic Settings1] screen appears
C
Click
A
B
Set the [IP Setting] item to
[DHCP Disable].
Enter the values you wish to
specify in the [IP Address],
[Subnet Mask] and [Default
Gateway] fields.
Select the [Time Zone].
A Set the [IP Setting].
● When selecting ADHCP DisableB:
Select ADHCP DisableB, and specify a value in the [IP Address], [Subnet Mask] and [Default
Gateway] fields.
● When selecting ADHCP EnableB:
The default setting is ADHCP DisableB(DHCP client function is Disabled). To assign an IP
address from the DHCP server, connect the DHCP server to the LAN, set the AIP SettingBof the
camera to ADHCP EnableB, and click the [OK] button. For details on IP addresses assigned to
the camera, consult your network administrator.
Note:
● Set the DHCP server such that the same IP address is always assigned to the MAC address of the
camera by the DHCP server. Connection may fail if the above setting is not performed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
B Select the [Time Zone].
C Click [OK].
3 A confirmation screen appears
Click [OK].
Camera restarts using the new IP address. It takes about one minute for the camera to reboot.
Memo:
● Access from the connected computer may fail when the IP address of the camera is changed. To
enable access to camera from the same computer, alter the IP address at the computer accordingly.
When the display or configuration of the opened screen appears strange, check
using the following procedures.
A Click [Start]-[Control Panel]-[Display] and open the [Display Properties] window
B Click the [Settings] tab in the [Display Properties] windows and click the [Advanced] button
C Check that [DPI setting] in the [General] tab has become [Normal size (96DPI)]
D Otherwise, change the setting to [Normal size (96DPI)] and reboot windows
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings
ⅷ Pages that users have access to
Restrictions are placed on the pages that users
have access to. In addition, links on the web
pages are also displayed according to the
access authority of the user.
Enter user name and password
User name and password entry will be required
at the beginning.
There are three access authorization levels to
camera. The factory settings are as follows.
● admin
(TX) is applicable to VN-X series only.
User
Name
Default
Authorization
Password levels
Basic Settings1 [Network]
[Time]
admin
jvc
jvc
All operations and
setting changes are
allowed
Basic Settings2 [Camera]
[Encoding]
[JPEG]
[MPEG4]
operator
Change of settings
other than those
related to network
and maintenance
are allowed
Details
[Camera]
[Encoding]
[Audio] (This feature is not
available in VN-V25U)
[Alarm]
[Alarm Environment]
[PTZ] (TX)
user
jvc
Viewing of images
is allowed
[Auto Patrol] (TX)
[Privacy Mask]
[Motion detection]
[Network Basic]
[Network Details]
[Protocol]
[Streaming]
[Access Restrictions]
[Time]
[Password]
[Maintenance]
[LED Settings]
[Miscellaneous]
[Operation]
[Settings]
[Position List] (TX)
[Patrol Settings] (TX)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
● operator
(TX) is applicable to VN-X series only.
Basic Settings2 [Camera]
[Encoding]
[JPEG]
[MPEG4]
Details
[Camera]
[Encoding]
[Audio] (This feature is not
available in VN-V25U)
[Alarm]
[Alarm Environment]
[PTZ] (TX)
[Auto Patrol] (TX)
[Privacy Mask]
[Motion detection]
[Streaming]
[LED Settings]
[Miscellaneous]
[Operation]
[Settings]
[Position List] (TX)
[Patrol Settings] (TX)
● user
Details
[Miscellaneous]
Memo:
● The [Security Settings] screen appears
before the top page is displayed. Press the
[Yes] button to proceed.
If you do not want this warning screen to be
displayed, change the Internet Explorer
settings as follows.
● Open [Tool]-[Internet Options]-[Security]
and select the [Trusted sites] icon.
● Next, press the [Custom Level] button,
followed by selecting AEnableBfor
[Miscellaneous]-[Display mixed content].
Note:
● Do not reset or turn off the power of camera
immediately after the settings are changed.
Otherwise, changes may not be saved, and
camera may be restored to the factory
settings.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting
How to open the setting page
1.Enter IP address of camera in the address bar of Internet Explorer (A Page 10)
A unified viewer is opened.
Click
2.Click [Details].
●
●
●
[Basic Settings1] page will be opened if accessed by user name
[Basic Settings2] page will be opened if accessed by user name
A
A
user
admin
operator
. (A
B
. (
A
Page 17)
Page 18)
Page 59)
B. (A
[Miscellaneous] page will be opened if accessed by user name
A
B
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Settings1
This page is for performing basic setting related to the network.
This page can be used during access using AadminB.
● Click [Basic Settings1].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
Click
A
B
C
D
E
F
Memo:
● You can open the [Basic Settings1] screen without going through the built-in viewer by entering the
following URL address (
● Enter the model name in lowercase letters.
（Example）
contains model name) in the address field of Internet Explorer.
VN- V225U series is displayed :
Network
A IP Setting
For setting the DHCP client function.
Connect camera to a network environment with a DHCP
server when DHCP is to be enabled. If the DHCP server does
not exist when [IP Setting] is set to ADHCP EnableB, camera
will start running with the 192.168.0.2 IP address and
255.255.255.0 subnet mask in about 2 minutes after startup.
(A Page 6)
B IP Address
For setting the IP address of camera.
For setting the subnet mask of camera.
C Subnet Mask
D Default Gateway
For setting the default gateway of camera.
Enter 0.0.0.0 if you do not want to set a default gateway.
Time
E Time
Displays the clock time of camera.
The time transmitted by camera is recorded in the JPEG
header. Discontinuity may occur in the JPEG header's time
immediately before and after changing the time.
F Time Zone
For setting the time zone.
G PC Time to Camera
Click the [Set] button to set the time of the computer on
camera.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Basic Settings2
Page for setting fundamental parameters of ACameraB, AJPEGBand AMPEG4B.
This page can be used during access using AadminBor AoperatorB.
● Click [Basic Settings2].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
Click
A
B
C
D
E
Memo:
● You can open the [Basic Settings2] screen without going through the built-in viewer by entering the
following URL address (
contains model name) in the address field of Internet Explorer.
● Enter the model name in lowercase letters.
（Example）
VN- V225U series is displayed :
18
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
A Camera ID
Character strings entered here will be written to the JPEG comment segment
(item name: camera). Refer to the API Guide on the file formats of JPEG.
B Monitor Type
For selecting the monitor type according to the monitor used to display the
video images. The picture quality varies according to the type of monitor
selected.
Custom
: Enables setting of picture quality according to the user's
preference. Detailed settings are configured on the detailed
settings page of the camera. (A Page 21)
LCD1,LCD2 : Picture quality setting for LCD monitors. Two types are
available for selection according to the user's preference.
CRT
: Picture quality setting for CRT (cathode-ray tube) monitors.
[Set values: Custom, LCD1, LCD2,CRT]
C Encoding
For selecting the frame size for each of the JPEG and MPEG4 screens from
A
Quad VGA
B
(1280 x 960)(
TX),
A
VGA
B
(640 x 480), and AQVGAB(320 x 240).
Select one of the four (
TV) or eight (TX) different patterns.
Memo:
● Refer to the API Guide on the file formats of JPEG.
Ⅵ Combination of distribution sizes and available features of
VN-V series
Distribution Size
Feature
Privacy Mask
JPEG/MPEG4
JPEG only
JPEG
MPEG4
QVGA
VGA
1
2
3
4
QVGA
QVGA
VGA
MPEG4 only
JPEG/MPEG4
QVGA
VGA
VGA
Ⅵ Combination of distribution sizes and available features of
VN-X series
Distribution Size
Feature
JPEG
MPEG4
VGA
Digital PTZ
Privacy Mask
1
2
3
4
5
6
7
8
QuadVGA
QuadVGA
QuadVGA
QuadVGA
QuadVGA
VGA
MPEG4 only
－
VGA
MPEG4 only
－
QVGA
－ T
MPEG4 only
－
－
JPEG only
－ T
JPEG only
－
VGA
JPEG/MPEG4
－
VGA
VGA
JPEG/MPEG4
－
QVGA
QVGA
JPEG/MPEG4
－
T Images are not distributed. It is displayed in white on viewer.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Basic Settings2 (continued)
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
DJPEG
Frame Size
For specifying the JPEG picture quality (rate control mode) and size (target file
size). When VFS1 to VFS7 is selected, the quantization table during JPEG
A
B
A
B
encoding will be maintained and the file size will increase/decrease according to
the input signals.
Typical sizes will be displayed in the Size field. When recording JPEG data to a
recorder with a limited storage capacity, the maximum recording time may vary
as the file size fluctuates under this setting.
When AAFSB is selected, encoding is performed such that the target file size is
the average size of multiple JPEG images.
You can enter the target size in the Size field.
[Picture quality values : VFS1 to VFS7, AFS]
Memo:
●
The picture size can be specified only when the picture quality value is set to
AFS.
[Size setting range in Quad VGA mode
[Size setting range in VGA mode 10 KB to 100 KB ]
[Size setting range in QVGA mode 3 KB to 33 KB ]
：40 KB to 200 KB ] (TX)
：
：
EMPEG4
Bitrate
For setting the MPEG4 encoding bit rate.
[Set values : 64 kbps to 8000 kbps]
Bitrate Control
For selecting whether to set the MPEG4 rate control mode to CBR (Constant Bit
Rate) or VBR (Variable Bit Rate).
CBR
: Encoding is performed at a fixed bit rate regardless of the condition of
the input video signals. Enables easy forecast of the bit rate.
VBR
: Changes the bit rate according to the condition of the input video
signals. Picture quality is stable, but forecast of the bit rate is difficult.
FPS
For setting the MPEG4 frame rate.
[Set values : 1 fps, 7.5 fps, 10 fps, 15 fps, 30 fps (TV)
]
I Frame Interval
For setting the I-frame interval. MPEG4 starts encoding from the I-frame.
Shortening the interval stabilizes the picture quality even when there are rapid
changes in the video image. However, the picture quality for images with little
change will deteriorate. In addition, when multicast packet loss occurs, the time
interval required to restore the image is shorter.
[Set values : 15, 30, 45, 60, 75]
Priority
For selecting whether to assign priority to the frame rate or picture quality during
MPEG4 encoding.
FPS
: Assigns priority to frame rate. Select this setting to enable smooth
monitoring of motion images.
Quality
: Assigns priority to picture quality.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Page
This page is for setting the camera’s parameters.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [Camera].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
To restore the settings of this page to the factory settings, press [Initialize] button.
Click
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
A
B
Camera ID
Character strings entered here will be written to the JPEG comment segment
(item name: camera). Refer to the API Guide on the file formats of JPEG.
Monitor Type
For selecting the monitor type according to the monitor used to display the
video images. The picture quality varies according to the type of monitor
selected.
Custom
: Enables setting of picture quality according to the user’s
preference.
LCD1, LCD2 : Picture quality setting for LCD monitors. Two types are
available for selection according to the user’s preference.
CRT
: Picture quality setting for CRT (cathode-ray tube) monitors.
[Set values: Custom, LCD1, LCD2, CRT]
Memo:
● Select ACustomBif you want to set the Gamma and Enhance frequency
values.
C
D
Black Level
For adjusting the black level. Lowering the value darkens the video image.
Increasing the value brightens the image.
[Setting range: 0 to 2]
Memo:
● If the black level is set to “0”, this may be too low depending on the
monitoring device, or dark area will become complete black.
● When using MPEG4 images, set to either “1” or “2”.
Gamma
To alter the appearance of dark areas in a video image, adjust the gamma
curve.
Off
: Do not perform gamma correction. The entire image appears dull.
-3 to 3 : Perform gamma correction. When this is set to “0”, standard gamma
correction is performed. Setting to a smaller value darkens the image,
while increasing the value brightens the image.
[Set values: Off, -3 to 0 to 3]
Memo:
●
The set value is fixed when the monitor type is set to
A
LCD1
B
,
A
LCD2
B
, or
A
CRT
CRT
B
.
E Enhance
For setting the type of edge enhancement.
Frequency
Low
High
: Enhances both thick and thin edges.
: Enhances thin edges.
[Set values: Low, High]
Memo:
●
The set value is fixed when the monitor type is set to
ALCD1
B,
ALCD2
B
, or
A
B.
F Enhance Level
For setting the intensity of edge enhancement.
Larger value : Increases the intensity of edge enhancement.
Smaller value : Decreases the intensity of edge enhancement.
[Setting values: -5 to 0 to 5]
22
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
G Color Level
For adjusting the color level.
Larger value
: Increases the color level.
Smaller value : Decreases the color level.
[Setting values: -5 to 0 to 5]
H AGC
For setting the AGC (automatic gain control) level.
Off
: Disables the AGC feature
Mid
High
Super
: When the amount of light is insufficient
: When the amount of light is particularly insufficient
: When the brightness level is insufficient even upon setting to
High.
[Set values: Off, Mid, High, Super]
Memo:
● This feature cannot be configured when the L Easy Day/Night feature is
set to ABlack and WhiteBor AAutoB.
● The AGC cannot be set when the L “B&W Mode” is set to “Black and
White” or “Auto Low, Auto Mid or Auto High”.
● The screen appears grainy at dark locations when the AGC feature is in
use.
I Sense Up
This feature is used to raise the sensitivity level by lengthening the exposure
time.
You can specify the number of times by which the sensitivity level is to be
increased automatically when the object becomes dark. When Ax16Bis
selected, the sensitivity level will automatically increases continuously until it
is 16 times of the level when AOffBis selected. When the sensitivity level
increases, the shutter speed slows down and motion becomes unnatural.
When set to AOffB, [Sense Up] is disabled.
[Set values: Off, x2(1/15s), x4(1/7.5s), x8(1/3.75s), x16(0.5s),
x32(1.1s),x62(2.1s)] (TV)
[Set values: Off, x2(1/7.5s), x4(1/3.75s), x8(0.5s), x16(1.1s), x22(1.5s)] (
TX)
Memo:
● Upon raising the sensitivity level, the screen may appear grainy or white,
or white defects may occur. However, this is not a malfunction.
● When Sense Up is set to a value other than AOffB, flickers occur under
the light of fluorescent or mercury lamps. This is not a malfunction of the
camera, but is due to principles related to Sense Up.
● When the shutter is set to a value between 1/250 to 1/10000, set
Sense Up to AOffB.
J ALC Priority
For setting the priority of ALC (feature for maintaining the video level
according to the brightness of the object). You can select whether to assign
priority to the motion or picture quality when the object becomes dark.
Motion
: Assigns priority to motion.
When the object becomes dark, priority is given to AGC
(automatic gain control), and therefore this is suitable for
shooting fast-moving objects.
Quality
: Assigns priority to picture quality.
When the object becomes dark, priority is given to the Sense
Up feature, and therefore this is suitable for shooting objects
requiring a high picture quality.
[Set values: Motion, Quality]
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Camera Page (continued)
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
K Shutter Speed
For setting the shutter speed.
Auto, Auto(1/15 - 1/100)
: Varies the shutter speed automatically according
to the brightness.
1/15 to 1/10000
Flickerless
: Fixed shutter speed.
: Reduces flickers due to fluorescent lamps.
[Set values : Auto, Auto(1/15 - 1/100)
(T
X), 1/15
(
T
X), 1/25
(TX), 1/30, 1/50,
1/60, 1/100,1/250, 1/500,1/1000, 1/2000, 1/4000, 1/10000, Flickerless]
Memo:
●
●
A
Auto
B
is only recommended when using a manual iris lens.
Flickers may occur when this is set to a value other than
A
1/50
B,
A1/100B, or
AFlickerless
B. When AFlickerlessBis selected, flickers may occur when the
Sense Up feature is used.
When Sense Up is set to a value other than
be set to a value between 1/250 to 1/10000.
●
AOffB, the shutter speed cannot
L Easy Day and
For setting the Easy Day and Night feature.
Color : Sets to the color mode at all times.
Black and White : Sets to the black-and-white mode at all times.
Night
VN-V25U
VN-X35U only
Auto
: Image color switches to black-and-white when the
luminance level is low.
[Set values : Color, Black and White, Auto]
Memo:
●
The threshold of the Auto switching cannot be changed.
LB&W Mode
VN-V26U
VN-V225U series
VN-X235U series
only
For specifying whether to switch the image to the B&W mode.
Auto mode can be specified for switching automatically to the black-and white
mode when the luminance level is low. In auto mode one of three levels can be
selected according to the luminance level.
Color
: Switches to the color mode at all times.
Black and White : Switches to the black-and-white mode at all times.
Auto Low
Auto Mid
Auto High
: Switches to the black-and-white mode when the luminance
of the signal level of the object is low.
: Switches to the black-and-white mode when the luminance
of the signal level of the object is medium.
: Switches to the black-and-white mode when the luminance
of the signal level of the object is high.
[Set values : Color, Black and White, Auto Low, Auto Mid, Auto High ]
Memo:
●
●
●
The infrared filter engages and disengages when switching between modes,
which causes mechanism noise.
During the occurrence of mechanism noise, the distribution sound from the
camera will be muted. (VN-V26U only)
When
A
Auto Low
B
,
A
Auto Mid
B
or
AAuto HighBhas been selected, the
camera will change the mode immediately according to the luminance level.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
M EV
Compensation
For setting EV (Exposure Value) correction. Enables setting between -9(-3EV) to
6(+2EV). You can specify settings in each 1/3 EV step. Decreasing the value
darkens the images, while increasing the value brightens the image.
[Set values: -9 to 0 to 6]
N White Balance
For selecting the white balance control feature. White balance can be adjusted
for a light source with a color temperature range of 2800K to 9500K.
ATW
Switches to the Auto-Tracking White Balance (automatic color temperature
tracking) mode. Adjusts the white balance automatically according to the color
temperature of the light.
AWC
Switches to the Auto-White Balance Control mode. In the AWC mode, values
entered for the [AWC R-GAIN] and [AWC B-GAIN] items are applied to white
balance.
One Push
AWC
Executes AWC (automatic white balance control).
Execute by placing a white object around the center of the screen in a location
with a lighting condition that is similar to the object to be shot.
Memo:
●
Pressing the [One Push] button replaces the [AWC R-GAIN] and [AWC B-
GAIN] values with the values of the AWC execution results.
Even when white balance is set to ATW, pressing the [One Push] button
switches the mode automatically to AWC.
●
AWC R-Gain For setting the gain of R (red) when in the AWC mode.
Larger value : Increases the redness.
Smaller value : Decreases the redness.
[Set values: 0 to 85 to 255]
AWC B-Gain For setting the gain of B (blue) when in the AWC mode
Larger value
: Increases the blueness.
Smaller value : Decreases the blueness.
[Set values: 0 to 219 to 255]
O Back Light
For selecting the backlight compensation feature. Set this feature when there
is a bright light source in the same direction as the object. Enables unwanted
light sources to be excluded from the photometry area.
Compensation
Off
: Disables backlight compensation.
Area1 to 4
: For selecting a photometry area from the four available
types.
[Set values: Off, Area1, Area2, Area3, Area4]
Photometry
Area
Photometry
Area
Photometry
Area
Photometry
Area
Photometry
Area
Off
Area1
Area2
Area3
Area4
Memo:
● The backlight compensation area is not linked to digital PTZ (TX).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Encoding Page
This page is for setting JPEG and MPEG4 encoding parameters.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [Encoding].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
● When settings on this page are altered during playback using the built-in viewer, reboot the viewer.
● There is upper limit to transmission bit rate from the camera. If a bit rate that exceeds upper limit is
specified, this new setting will not be applied. For details on the maximum transmission limit, refer to
the section on ANetwork RequirementsB(A Page 3).
Click
A
B
C
D
E
F
G
26
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
A Frame Size
For selecting the frame size of each JPEG or MPEG4 screen to
Quad VGA (1280 960) ( X), VGA (640 480) or QVGA (320
ן T
ן ן 240).
Select one of the four (TV) or eight (TX) different patterns. (A Page 19)
JPEG
B Quality/Size
For specifying the JPEG picture quality (rate control mode) and size
(target file size).
When AVFS1Bto AVFS7Bis selected, the quantization table during
JPEG encoding will be maintained and the file size will increase/
decrease according to the input signals. Typical sizes will be displayed
in the Size field. . When recording JPEG data to a recorder with a
limited storage capacity, note that the maximum recording time may
vary as the file size fluctuates under this setting.
When AAFSBis selected, encoding is performed such that the target
file size is the average size of multiple JPEG images. You can enter the
target size in the Size field.
[Quality field set values: VFS1 to VFS7, AFS]
Memo:
● The picture size can be specified only when the picture quality
value is set to AFS.
[Size setting range in Quad VGA mode:40 KB to 200 KB ](TX)
[
[
Size field setting range for VGA:10 KB to 100 KB ]
Size field setting range for QVGA:3 KB to 33 KB ]
MPEG4
C Bitrate
For setting the MPEG4 encoding bit rate.
[Setting range: 64 kbps to 8000 kbps]
D Bitrate Control
For selecting whether to set the MPEG4 rate control mode to CBR
(Constant Bit Rate) or VBR (Variable Bit Rate).
CBR
: Encoding is performed at a fixed bit rate regardless of the
condition of the input video signals. Enables easy forecast of
the bit rate.
VBR
: Changes the bit rate according to the condition of the input
video signals. Picture quality is stable, but forecast of the bit rate
is difficult.
E Frame Rate
For setting the MPEG4 frame rate.
[Setting range: 1 fps, 7.5 fps, 10 fps, 15 fps, 30 fps (TV)]
F I Frame Interval
For setting the I-frame interval. MPEG4 starts encoding from the I-
frame. Shortening the interval stabilizes the picture quality even when
there are rapid changes in the video image. However, the picture
quality for images with little change will deteriorate. In addition, when
multicast packet loss occurs, the time interval required to restore the
image is shorter.
[Set values: 15, 30, 45, 60, 75]
G Priority
For selecting whether to assign priority to the frame rate or picture
quality during MPEG4 encoding.
FPS
: Assigns priority to frame rate. Select this setting to enable
smooth monitoring of motion images.
Quality
: Assigns priority to picture quality.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Audio Page
(This feature is not available in VN-V25U)
This page is for setting the audio parameters.
This page can be used during access using AadminBor AoperatorB
● Click [Advanced Settings] to display setting menu.
● Click [Audio].
●
To enable the new settings, press the [OK] button.
Click
A
C
B
D
28
Download from Www.Somanuals.com. All Manuals Search And Download.
A Duplex Mode
For setting the audio transmission method.
When half duplex is selected, audio sent to computers from the camera is
muted when audio is transmitted from a computer to the camera.
When full duplex is selected, you can send audio to the camera from a
computer while listening to audio sent to computers from the camera.
[Set values: Half Duplex, Full Duplex]
Memo:
● When this is set to Full Duplex, audio sound sent to the camera can be
returned trough built-in or external microphone to the computer as echo.
B Mike Gain
For setting the gain value for the external microphone connected to the camera.
[Set values: 0 dB, 20 dB, 26 dB, 32 dB, AGC]
For setting the gain value for the camera’s built-in microphone. (VN-V26U only)
[Set values: 0 dB, 20 dB, 26 dB, 32 dB]
C Mike Power
For specifying the power supply for the external microphone connected to
the camera.
[Set values : On, Off]
Supply
(This feature is not
available in VN-V26U)
D Audio File No.1
For registering audio files that can be outputted from the audio output
terminal of camera when an alarm is triggered.
to No.5
Ⅵ To output the registered audio file:
specifications, and register it to the camera.
Audio file specifications
ࡗ File format ࡗ Encoding format : WAV file
: linear PCM
ࡗ Sampling frequency : 8 kHz ࡗ Quantization bit ࡗ Monaural ࡗ Maximum size : 16 bit
: 30 seconds (total of playback files 1 to 5)
● Configure the action item on the Alarm page to [Play Audio]
(A Page 30)
Note:
● Playback of the audio file stops if the audio transmission feature of
Built-in Viewer is enabled during playback of the file.
● When the audio transmission feature of Built-in Viewer is running,
audio files cannot be played back.
Press the [Register] button to register the selected audio file on the camera.
Press the [Delete] button to delete an audio file registered on the camera.
Press the [Browse] button to show the file selection screen and make a
selection from the available audio files.
Press the [Play] button to play back an audio file registered on the camera,
and send output to the Audio signal output terminal of the camera.
Press the [Stop] button to stop playing an audio file.
Memo:
● WAV file can be recorded or created using Windows Sound Recorder or
general sound editing software.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Alarm Page
This page is for setting actions when there is an alarm.
Up to 5 actions (No. 01 to No. 05) may be set.
This page can be used during access using AadminBor AoperatorB.
●
Click [Advanced Settings] to display setting menu.
●
●
Click [Alarm].
Press the [OK] button to enable the new settings. Only items that are valid under the selected action will be
saved. When Disable is selected for the action, all settings will be restored to their default values.
If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be
denied. Press the [Cancel] button to restore the invalid entry to the current value.
●
Click
A
B
C
D
E
F
G
H
I
J
K
30
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
A Action For specifying the type of action.
Disable
Mail
: Does not trigger any action.
:Sends out e-mail. Specify the recipient’s mail address. The title
of the mail will appear as [Alarm from Amodel nameB] (E.g.,
AVN-V225Bis displayed for VN-V225VPU) and the sender as
[Camera ID]. Enter the message to send in [Mail Text]. Input up
to 127 alphanumeric characters. To attach the latest image to
the mail, set [Attach Image] to AOnB.
FTP
: Sends out pre-/post-recorded JPEG files via FTP. See the page
on Alarm Environment for details on pre-/post-recording and
FTP server settings. (A Page 34)
The maximum transmission rate of FTP is 1 Mbps. If a new FTP
trigger occurs during post-recording, the recorded portion is
treated as pre-recording and a new post-recording starts.
During FTP transmission after completing the post-recording, a
new post-recording starts if a new FTP trigger occurs.
TCP
UDP
: Sends out the character string entered in the [TCP/UDP Data]
field to the destinations specified in [TCP/UDP IP Address] and
[TCP/UDP Port Number] via TCP.
: Sends out the character string entered in the [TCP/UDP Data]
field to the destinations specified in [TCP/UDP IP Address] and
[TCP/UDP Port Number] via UDP.
Output 1 Break : Changes Alarm Output 1 to Break.
Output 2 Make : Changes Alarm Output 2 to Make.
Output 2 Break : Changes Alarm Output 2 to Break.
Set the alarm output time in the [Alarm Output Duration]
field.
Position (TX)
: Moves to the preset position specified in the Action
Position No. item E.(A Page 32)
Play Audio (This feature is not available in VN-V25U)
: Play back an Audio File registered on the camera.
(A Page 29)
(The following setting values are for VN-V26U, VN-V225U series and VN-
X235U series.)
BlackWhite B Color
: Changes the [B&W Mode] setting from ABlack and
WhiteBto AColorB.
Color B BlackWhite
: Changes the [B&W Mode] setting from AColorBto ABlack
and WhiteB.
DayNight:Auto Low
: Changes the [B&W Mode]setting to AAuto LowB.
DayNight:Auto Mid
: Changes the [B&W Mode] setting to AAuto MidB.
DayNight:Auto High
: Changes the [B&W Mode] setting to AAuto HighB.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Alarm Page (continued)
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
B 1st Trigger
For specifying the first trigger to be activated.
[Set values : Input 1 Make, Input 2 Make, Input 1 Break, Input 2 Break, Motion
detection, Position
BlackWhite Color
Color BlackWhite
(
T
(
(
X)
VN-V26U
VN-V26U
,
B
,
,
VN-V225U series and VN-X235U series only)
,
B
VN-V225U series and VN-X235U series only)]
Memo:
●
When the second trigger is turned off, the action will be invoked only by the first
trigger.
●
If [Motion detection] or [Position] (
TX) is selected as the first trigger, [Max.Interval]
and [2nd Trigger] cannot be selected.
C Max. Interval
Enabled when both the first and second triggers are specified.
Specify the maximum interval between the first and second triggers. An
action will be invoked only if the interval between the first and second
triggers is within the maximum interval.
[Setting range : 1 msec to 3600 msec]
D 2nd Trigger
For specifying the second trigger for invoking an action.
Either alarm input (make) or alarm input (break) can be selected.
[Set values:Input 1 Make, Input 2 Make, Input 1 Break, Input 2 Break]
E Action Position
For setting the position number to move to when the [Action] item A is set to
APositionB.
No
(TX)
[Setting range : 0 to 19]
F Audio File
For setting the file number to play back when the [Action] item A is set to
APlay AudioB.
[Setting range : 0 to 5]
G Trigger Position
For setting the file number to move when the [1st Trigger] item B is set to
APositionB.
No
(TX)
[Setting range : 0 to 19]
32
Download from Www.Somanuals.com. All Manuals Search And Download.
H Mail
Mail Address : For entering the recipient’s mail address.
Mail Text : For entering the mail transmission data. Input up to 127
alphanumeric characters.
Attach Image : For specifying whether to attach images to the mail.
I TCP/UDP
TCP/UDP IP Address : For entering the address when alarm action
notification is to be sent via TCP or UDP.
(IP or FQDN)
TCP/UDP Port Number : For entering the port number when alarm action
notification is to be sent via TCP or UDP.
(1 to 65535)
TCP/UDP Data
: For entering the data to send during TCP or UDP
notification. Input up to 127 alphanumeric
characters.
J Alarm Output
For setting the alarm output time from the alarm output terminal.
Duration
When this is set to “0”, it is not possible to revert back to break (or make)
after changing to make (or break).
[Setting range: 0, 100 msec to 5000 msec]
K Time Filter
For specifying the alarm action with respect to each day of the week and
setting the corresponding time of the day.
Applicable day of week
: Sunday, Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday
Alarm action
Unmask Span
: For specifying the time period for invoking the
action
Mask Span
Unmask All
: For specifying the time period to stop the action
: Activated at all times
Mask All
: Stopped at all times
Applicable time period
: For specifying the start and end time in hours
and minutes.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Alarm Environment Page
This page is for setting alarm-related environments.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [Alarm Environment].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
Click
A
B
34
Download from Www.Somanuals.com. All Manuals Search And Download.
A Mail
For setting the mail environment when [Mail] is specified as an action on the
Alarm page.[SMTP] and [POP] can be used. Configure only the [SMTP]
settings under usual circumstances.
Enter the camera’s mail address as the recipient’s mail address.
Configure the [POP] settings as well if [POP before SMTP] is enabled. In
addition, if FQDN is set for [SMTP Server], configure also the DNS server
settings on the [Network Basic] page. (A Page 45)
Memo:
What is FQDN (Fully Qualified Domain Name)?
This is a fully qualified domain name that indicates a notation method of
describing the entire host or domain name on the TCP/IP network without
abbreviating.
For example, if the host name is www and the domain name is victor.co.jp,
B FTP
For setting the FTP environment when [FTP] is specified as an action on the
Alarm page. This is common with the FTP environment when using the
periodic FTP on this page.
When [Directory] is left blank, FTP transfer will be performed to the home
directory of the FTP server. To enable FTP transfer to a directory below the
home directory, set the corresponding directory name in [Directory].
Delimit the directory using “/”.
Example: subdir1/subdir2
Destination directory of FTP transfer will be dependent on the FTP server if
“/” is added at the beginning.
Setting [Periodic FTP] to AOnBenables transfer of the latest JPEG images to
the FTP server at regular intervals. Specify the interval in seconds for
[Periodic FTP Interval].
File name: Select a type from the two types of periodic FTP file names.
When AAutoBis selected, images are generated from the year, month, day,
hour, minute, second, and number.
Example: 20071114161032-001-2.jpg
When AManualBis selected, you can select a file name generation method
from the following.
● File name containing only the character string entered in [User-defined-
name]
Example: Camera1.jpg
● File name with the year, month, day, hour, minute, and second added to
[User-defined-name]
Example: Camera1_20071114161032001.jpg
The name of the file to be transmitted via FTP is made up of the action
number, year, month, day, hour, minute, second, number and trigger flag.
Example: 01-20070711152904-001-0.jpg
The first two digits are the action number, and the following 14 digits denote
the year, month, day, hour, minute and second.
The three digits after the first hyphen is the number of the series of JPEG
files to be sent via the FTP. The number starts from “000”. The last digit
denotes the trigger flag. This is displayed as “1” only for the JPEG file during
a trigger input, and as “0” if otherwise.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Alarm Environment Page (continued)
B
C
36
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
B FTP (continued)
Time Filter:
For specifying the periodic FTP transfer action with respect to each day of
the week and setting the corresponding time of the day.
Applicable day of week : Sunday, Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday
Alarm action
Unmask Span
: For specifying the time period for invoking the
action
Mask Span
Unmask All
Mask All
: For specifying the time period to stop the action
: Activated at all times
: Stopped at all times
Applicable time period : For specifying the start and end time in hours and
minutes.
Pre-/Post-recording parameter:
[PrePostRecording Frame Rate] : For specifying the JPEG frame rate for
FTP pre-/post-recording.
[Set values : 1 fps, 2 fps, 3 fps, 5 fps,
6 fps, 7.5 fps, 10 fps,
15 fps, 30 fps (TV)]
[PrePostRecording Before Trigger] : For setting the FTP pre-recording
trigger time (recording time before
alarm input) in seconds.
[Setting range: 0 to 60 seconds]
[PrePostRecording After Trigger] : For setting the FTP post-recording
trigger time (recording time after alarm
input) in seconds.
[Setting range: 0 to 60 seconds]
The maximum time intervals for [PrePostRecording Before Trigger] and
[PrePostRecording After Trigger] are determined by the JPEG size on the
Encoding page as well as the set values for [PrePostRecording Frame Rate].
A message appears if the combination of the entered values are not feasible.
C Alarm Output
For setting the alarm output.
Duration
For setting the output time of [Manual Output].
[Setting range : 0, 100 msec to 5000 msec]
Manual
Output
For operating alarm output manually.
The current output status appears on the right. When [Duration] is set to “0”,
pressing the [Make] button switches the alarm to Make output, while
pressing the [Break] button switches the alarm to Break output.
When [Duration] is set to a value other than “0”, pressing the [Make] button
switches the alarm to Make output only during the duration of the output,
upon which it switches to Break output.
When the output duration is set to a value other than “0”, pressing the
[Break] button switches the alarm to Break output only during the duration of
the output, upon which it switches to Make output.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
PTZ Page
(VN-X series only)
This page can be used during access using AadminBor AoperatorB.
● First of all, configure the encoding settings. (A Page 19)
● Click [Advanced Settings] to display setting menu.
● Click [PTZ].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
Note:
● This feature does not work for some combinations of distribution sizes on the Encoding page.
(A Page 19)
Click
A
B
C
A Auto Return
Restores automatically to the state specified under [Mode] when action is
not performed on the manually operated camera over the interval specified
in [Return Time].
Mode
For setting the action after Auto Return.
None
: Auto Return disabled.
: Returns to the home position.
: Restores the auto patrol action.
HOME
Auto Patrol
Return Time
For setting the time interval before restoring the action via Auto return.
[Set values : 1 minute, 2 minutes, 3 minutes, 5 minutes, 10 minutes,
20 minutes, 30 minutes, 60 minutes]
Test
Click [Execute] to perform a test execution of the preset Auto Return action.
B Limit
Zoom Limit
Set maximum value of electronic zoom feature.
[Set values : 1 , 2 , 4 , 8 ]
C Preset Position
For adjusting the speed of movement to the Preset Position.
This is also applicable to movement to the Preset Position in the Auto Patrol
mode.
Speed
Speed
[Set values : Moment, Low, Mid, High]
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Patrol Page
(VN-X series only)
Perform Auto Patrol setting to switch image display between multiple positions according to the interval
that has been set. Set when viewing registered positions in order.
This page can be used during access using AadminBor AoperatorB.
● First of all, configure the encoding settings. (A Page 19)
● Click [Advanced Settings] to display setting menu.
● Click [Auto Patrol].
● Register position using PTZ feature. (A Page 70)
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
Note:
● This feature is available for images that work with digital PTZ. (A Page 19)
Whole shooting
HOME (No 0)
Position１
No 1
Position ２
No ５
Position ３
No ２
Position 4
No ４
Position ５
No ３
No.0(HOME)
No. 1 (Position 1)
No. 2 (Position 3)
No. 5 (Position 2)
No. 4 (Position 4)
No. 3 (Position 5)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Auto Patrol Page (continued)
(VN-X series only)
Click
A
B
C
D
E
A No.
Switches the camera images in sequence from No. 0 to No. 19.
Shows the title of the position.
B Title
C Position
For setting the sequence of position numbers in which the camera moves.
[Set values : 0 to 19]
D Stay Time
For setting the time interval for displaying the image of the respective positions.
(Unit: seconds)
Select Skip for positions that you do not want to display during Auto Patrol.
[Set values : Skip, 10, 20, 30, 45, 60, 120]
E Moving speed For setting the speed of movement to the said position.
[Set values : Moment, Low, Mid, High]
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Privacy Mask Page
Privacy Mask is a feature that enables masking of a portion of the image.
The camera enables unlimited privacy masks to be specified in different shapes at your favorite
locations. The Privacy Mask masks area by uploading a BMP file painted in red (created separately).
The displayed color is determined by the color specified on this page.
This page can be used during access using AadminBor AoperatorB.
● First of all, configure the encoding settings. (A Page 19)
● Click [Advanced Settings] to display setting menu.
● Click [Privacy Mask].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
Note:
●
This feature does not work for some combinations of distribution sizes on the Encoding page.
(
A
Page 19)
Memo:
●
This feature does not work correctly on analog video signal.
Click
A
B
C
Mask Color Settings Screen
D
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Privacy Mask Page (continued)
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
A Mode
For specifying whether to activate the Privacy Mask feature.
When this is set to AOnB, the privacy mask specified using the following
items will appear on the image.
B Masking Data
the position and shape of the privacy mask on the computer in advance.
(Refer to the following for procedures to create the BMP file.)
Press the [Browse...] button to display the file selection screen. Select the
BMP file in the PC.
Press the [Upload] button to upload the selected BMP file to the camera.
Creating the BMP file
1. Upon installing the camera, use JPEG Viewer to save the JPEG file on
the computer. (JPEG Viewer : A Page 74)
2. Open the saved JPEG file on the computer using the Paint tool, and paint
the area to be masked in red ((R, G, B) = (255, 0, 0)).
3. Save this image as a BMP file (24 bits).
C Masking Color
Press the [Settings] button to display the Masking Color Setting screen.
You can alter the color of the privacy mask.
D Masking Color
For specifying the color ratio in the red : green : blue format.
Press the [Save] button to set the selected color as the mask color.
Press the [Default] button to restore the default mask color settings.
Setting
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Motion Detection Page
This page is for setting motion detection.
This page can be used during access using AadminBor AoperatorB.
Memo:
● When images on the camera are currently acquired by the built-in viewer or another client, video
images may not appear on the [Motion detection] page if it is beyond the distribution capability of the
camera.
● Click [Advanced Settings] to display setting menu.
● Click [Motion detection].
● The area valid for motion detection is displayed in blue.
● When motion is detected, the frame of the built-in viewer turns red.
Click
A
B
C
D
E
F
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Motion Detection Page (continued)
A Display Screen
The screen is divided into blocks of 10 (horizontal) x 8 (vertical). You can
specify whether to enable motion detection in each block. Clicked block
turns blue. Click again to return to the original natural color. When the block
turns blue, it is unmasked and motion can be detected. Press the [OK]
button to enable this setting. When the screen of the block is in its natural
color, it is masked and motion cannot be detected in it. All blocks are
masked in the default setting.
Press the [OK] button to enable this setting.
Use the [Mask All] button to mask all blocks.
Use the [Clear Mask] button to unmask all blocks.
B Detection
For setting motion detection to On/Off.
Press the [OK] button to enable motion detection in the unmasked blocks.
Memo:
● Even though motion detection is set to AOnB, the motion of masked
blocks cannot be detected.
C OK/Cancel
D Level
To apply the new parameters, press the [OK] button. Press the [Cancel]
button to cancel the change.
For setting the sensitivity of motion detection.
Increasing the number raises the detection sensitivity level, and hence it is
more sensitive.
Press the [OK] button to enable this setting.
[Set values : 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10]
E Mask All
Masks all blocks.
Press the [OK] button to enable this setting.
F Clear Mask
Unmasks all blocks and enables the current motion detection and detection
sensitivity settings.
Press the [OK] button to enable this setting.
Memo:
● The area display position serves as a reference. Make sure to perform operation check.
● The screen is divided into blocks of 80 (10 horizontal x 8 vertical).
Set the angle of view such that the size of the object for which motion is to be detected is larger than
the size of multiple blocks.
Note:
● This feature may not function properly depending on the conditions of the object and settings.
● Flickers of fluorescent lamps may cause motion detection.
● Changes in brightness due to the light source may be detected as motion.
● The motion detection feature is not intended to prevent theft or fire.
● Our company shall not be liable for any accident or damage that occurs.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Basic Page
This page is for performing basic setting related to the network.
This page can be used during access using AadminB.
● Click [Advanced Settings] to display setting menu.
● Click [Network Basic].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
● When settings of the [Network Basic] page is changed, all services that are currently running will
end immediately. For example, when changes are made to the [Network Basic] page during JPEG/
MPEG4 distribution, distribution will be discontinued and TCP will be disconnected.
A
B
C
D
E
F
G
H
I
Click
A IP Setting
For setting the DHCP client function.
Connect the camera to a network environment with a DHCP server when
DHCP is to be enabled.
If the DHCP server does not exist when DHCP is set to AEnableB, Camera
will start running with the 192.168.0.2 IP address and 255.255.255.0 subnet
mask in about 2 minutes after startup.
Refer to AIP Address SettingsB(A Page 6) for the IP address.
B IP Address
For setting the IP address of the camera.
C Subnet Mask
For setting the subnet mask of the camera.
D Default Gateway For setting the default gateway of the camera.
Set as 0.0.0.0 when a default gateway is not set.
E Host Name
For setting the host name of the camera.
Specify a name using alphanumeric characters, hyphen (-) or period (.).
Underscores (_) cannot be used.
F DNS Server
G MAC Address
H IP Protocol
I IPv6 Address
For setting the address of the DNS server.
The MAC address of the camera is displayed in a hexadecimal number.
For setting IPv6 to On or Off. (IPv4 is set to On at all times.)
Two types of addresses, “link local” and “global”, are displayed when IPv6
settings are enabled. However, if the connected network does not support
IPv6, “Disabled” appears in the “global” address field.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Network Details Page
This page is for performing detailed network setting.
This page can be used during access using AadminB.
● Click [Advanced Settings] to display setting menu.
● Click [Network Details].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
A
B
C
D
E
F
G
Click
A JPEG TOS(DS field)
For setting the TOS value of IP packets in which JPEG is stored.
The upper six bits out of the eight bits that make up the TOS value
belong to DSCP.
This upper six bits can be set. The lower two bits are “0”. For example,
upon setting to “250”, the lower two bits are converted to “0”, and the
value becomes “248”.
TOS values are used in networks that support QoS. By setting QoS for
the network switch, routing can be done by giving priority to packets with
a larger TOS value.
B MPEG4 TOS(DS field) For setting the TOS value of IP packets in which MPEG4 is stored.
For details, refer to the [JPEG TOS(DS field)] item above.
C Audio TOS(DS field)
For setting the TOS value of IP packets in which Audio is stored.
For details, refer to the [JPEG TOS(DS field)] item above.
(This feature is not
available in VN-V25U)
D TTL( Unicast)
E TTL( Multicast)
For setting the TTL value of JPEG/MPEG4 packets that are to be sent via TCP.
For setting the TTL value of JPEG/MPEG4 packets that are to be sent via
multicast.
F MTU
For setting the maximum packet size for storing JPEG/MPEG4.
[Setting range: 1280 to 1500]
G Negotiation
For setting the negotiation of the network. When a value other than
“Auto” is selected, do not set the connected network device to “Auto”.
Ensure that it is set to the same value as the camera.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Protocol Page
This page is for changing the HTTP server port number.
This page can be used during access using AadminB.
● Click [Advanced Settings] to display setting menu.
● Click [Protocol].
● Press the [OK] button to enable the new settings.
● After changing, you will need to re-establish the connection if you are using the Internet Explorer.
A
B
C
D
E
Click
Protocol Settings
For setting the protocols.
A HTTP Server Port You can change the port number for the built-in web server of the camera.
(1 to 65535: The default port number setting is 80.)
The JPEG and MPEG4 HTTP port number for the web server will also be
changed. During access to the camera from the Internet Explorer, enter
the following in the Internet Explorer when the camera is in its default
settings.
If the port number is changed to 8080, for example, enter the Internet
Explorer as follows.
B VSIP Protocol
For setting VSIP to On/Off.
C VSIP Server Port For changing the built-in VSIP number of the camera.
(1 to 65535: Default value is 5510)
D AMX Device
Discovery
For setting AMX Device Discovery Protocol to On or Off.
Set to AOnB when you are using the camera on AMX's systems.
[Set values : On, Off]
Protocol
JPEG Streaming
For selecting the priority for distributing JPEG images.
E Priority
For selecting whether to assign priority to the number of clients or frame
rate for distributing JPEG images.
client number : Assigns priority to number of clients for distribution.
(A Page 4)
When the distribution request increases, the frame rate
for JPEG distribution is reduced to enable distributions
up to 20, the maximum clients.
frame rate
: Assigns priority to frame rate. (A Page 4)
Set to this mode if you wish to maintain the JPEG frame
rate as requested by the clients. When a distribution
request that exceeds the maximum number of
distributions is received, this request is denied.
Memo:
● If the built-in viewer is used for playback, change the HTTP port number in the setting screen of the
built-in viewer to the same value.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Streaming Page
This page is for setting manual multicast transmission.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [Streaming].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
A
B
C
D
E
G
F
H
I
J
Click
48
Download from Www.Somanuals.com. All Manuals Search And Download.
JPEG
A Control
For starting or stopping streaming of JPEG images.
Parameters that are set on the [Streaming] page will be saved when
transmission is started upon pressing the [Start] button.
B Destination
For specifying the destination address of JPEG streaming.
Specify the multicast address. When other devices that make use of
multicast transmission exist, ensure that each of them is set to a different
multicast address.
Address
C Destination Port For specifying the destination port number of JPEG streaming.
Specify an even number for RTP compliance.
When other devices that make use of multicast transmission exist, it is
recommended that each of them be set to a different port number.
Multiple multicast streams cannot be received on a single computer when
there are duplicate port numbers.
D Frame Rate
MPEG4
For specifying the frame rate when sending JPEG images via multicast.
E Control
For starting or stopping streaming of MPEG4 images.
Parameters that are set on the [Streaming] page will be saved when
transmission is started upon pressing the [Start] button.
F Destination
For specifying the destination address for MPEG4 streaming.
Specify the multicast address. When other devices that make use of
multicast transmission exist, ensure that each of them is set to a different
multicast address.
Address
G Destination Port For specifying the destination port number for MPEG4 streaming.
Specify an even number for RTP compliance.
When other devices that make use of multicast transmission exist, it is
recommended that each of them be set to a different port number.
Multiple multicast streams cannot be received on a single computer when
there are duplicate port numbers.
Audio (This feature is not available in VN-V25U.)
H Control
For starting or stopping streaming of audio.
Parameters that are set on the [Streaming] page will be saved when
transmission is started upon pressing the [Start] button.
I Destination
For specifying the destination address of audio streaming.
Specify the multicast address. When other devices that make use of
multicast transmission exist, ensure that each of them is set to a different
multicast address.
Address
Specify an even number for RTP compliance.
When other devices that make use of multicast transmission exist, it is
recommended that each of them be set to a different port number.
Multiple multicast streams cannot be received on a single computer when
there are duplicate port numbers.
Memo:
● When the power of the camera shuts down accidentally during multicast transmission, multicast
transmission will restart automatically after the camera is rebooted.
● When the setting on the Encoding page is set to a pattern where MPEG4 is not available, MPEG4
multicast transmission cannot start.
ACombination of distribution sizes and available features of VN-X seriesB(A Page 19)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Access Restrictions Page
(VN-V25U does not have audio.)
This page is for setting client restrictions.
This page can be used during access using AadminB.
● Click [Advanced Settings] to display setting menu.
● Click [Access Restrictions].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
● This feature is applied to JPEG / MPEG4 / Audio acquisition. It does not impose restrictions on
access via a web browser or use of API.
Note:
● The Access Restriction feature determines whether to impose restrictions during TCP connection by
the client. In the case when access restriction is set after TCP connection by a client has been
established, TCP connection will not be disconnected.
A
B
Click
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Destination Address
Restrictions may be imposed on clients accessing the camera using the IP
address.
A Access
When AdenyBis selected, acquisition of JPEG / MPEG4 / Audio via the IP
address specified for the [IP Address] item will be denied. Restrictions are
not imposed on access to the Web Settings page.
Restrictions
When AallowBis selected, acquisition of JPEG / MPEG4 / Audio via the IP
address specified for the [IP Address] item will be permitted. Restrictions
are not imposed on access to the Web Settings page.
B IP Address
When a multicast address is specified and AdenyBis selected, camera will
deny transmission to this multicast address.
When a multicast address is specified and AallowBis selected, camera will
only accept transmission to this multicast address and deny transmission
to multicast addresses that are not stated in the [IP Address] field.
Note:
● Note that when AallowBis selected and all IP address fields are left blank, JPEG / MPEG4 / Audio
acquisition by all IP addresses will be denied.
Restrictions are not imposed on access to the Web Settings page.
Additionally, Camera will also deny access when instructions for transmission to the specified IP
address are sent via API.
Memo:
● To specify a specific IP address range, enter a combination of the IP address and subnet mask in
the [IP Address] field.
● Define the subnet mask using a length between 8 to 30 bits.
For example, a range between 192.168.0.0 to 192.168.0.255 is denoted as 192.168.0.0/24 ([IP
Address]/[bit length of subnet mask]).
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Time Page
This page is for setting time.
This page can be used during access using AadminB.
● Click [Advanced Settings] to display setting menu.
● Click [Time].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
A
B
C
D
E
F
Click
A SNTP
For setting the SNTP client feature.
When this is set to AOnB, the system accesses the specified NTP server at
regular intervals to acquire the time.
In addition, time will be recorded in the JPEG headers distributed by the
camera. Discontinuity in JPEG header’s time may occur immediately before
and after acquiring time from the NTP server.
B NTP Server
C Access Interval
D Time
For setting the IP address of the NTP server.
For setting the time interval for access to the NTP server.
Displays the time on the clock of the camera.
The clock time can be changed by entering an appropriate value. (Second
value cannot be specified.)
In addition, time will be recorded in the JPEG headers distributed by the
camera. Discontinuity may occur in the JPEG header’s time immediately
before and after changing the time.
E Time Zone
For setting the time zone.
F Pc time to
Click [Set] to load the clock time of the computer in use on the camera.
Camera
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Password Page
This page is for setting the password.
This page can be used during access using AadminB.
● Click [Advanced Settings] to display setting menu.
● Click [Password].
● Press the [OK] button to enable the new settings.
A
B
C
Click
A Username
Select a user name.
B New Password
Enter a new password.
Passwords shall be at least 1 characters and not longer than 8 characters.
Camera is case sensitive.
C New Password
Enter again to confirm the new password.
Again
Note:
● Be sure to handle the password carefully in case you forget it.
● In the event that you forget the password, please consult JVC’s servicing center.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Maintenance Page
This page is for maintenance purposes.
This page can be used during access using AadminB.
● Click [Advanced Settings] to display setting menu.
● Click [Maintenance].
A
B
C
Click
A Restart
Restarts the camera. (It takes about one minute for the camera to restart.)
B All Settings
AInitializeB
Restores all settings to their default values and reboots the unit. (It takes
about one minute for the camera to initialize and reboot.)
Passwords will also be initialized. The built-in clock of the camera will not be
affected. JPEG/MPEG4 transmission and all others services that are
running will be discontinued.
C Update
Upgrades the firmware version of the camera and reboots the unit.
The settings of the camera will be saved. Copy the new firmware file to the
computer on which Internet Explorer is used, and specify this file using the
[Browse...] button. Press the [Update] button to start the update. JPEG/
MPEG4 transmission and all others services that are running will be
discontinued. The update process may take several minutes.
A message will be displayed on the Internet Explorer when update is
successfully completed.
Note:
● Do not turn off the power when update is in progress or during reboot
after update is complete. Turning off the power of the camera may cause
it to malfunction.
● Before update, end the accesses to the camera from pages other than
this page (Built-in Viewer etc). If update is started while accesses other
than this page are valid, access to this page might be cut off. In that case,
end the accesses other than this page, access to this page again to redo
the update.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
LED State Page
This page is for setting the method for lighting the [STATUS] indicator on this camera.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [LED State].
● Press the [OK] button to enable the new settings.
A
B
Click
A LED State
For selecting whether to light up the [STATUS] indicator on this camera
when it is running.
Enable
Disable
: Lights up when unit is running.
: Turns off the indicator after startup is complete.
B Identify Unit
If you want the [STATUS] indicator on this camera to blink such as during
visual check of the camera currently being configured from the computer, set
this item to ABlinkB.
Memo:
● The light of the indicator remains off when the LED State is set to
ADisableBeven if ABlinkBis set.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Ⅵ Encoding Page (A Page 26)
Setting (continued)
Item
Frame Size
Factory Settings
VGA/VGA (TV)
Quad VGA/VGA
Digital PTZ
List of Factory Settings of Each Page
(TV) is applicable to VN-V series only. (TX) is
applicable to VN-X series only.
JPEG Quality
VFS4
2000 kbps
CBR
Ⅵ Camera Page (A Page 21)
MPEG4 Bitrate
Item
Camera ID
Factory Settings
MPEG4 Bitrate Control
MPEG4 FPS
model name
(E.g.,
15 fps
30
MPEG4 I Frame Interval
MPEG4 Priority
AVN-V225Bis
displayed for
FPS
AVN-V225VPUB)
Ⅵ Audio Page (A Page 28)
(This feature is not available in VN-V25U)
Monitor Type
Black Level
Gamma
Custom
1
Item
Duplex Mode
Factory Settings
0
Half Duplex
32 dB
Enhance Frequency
Enhance Level
Color Level
AGC
High
Mike Gain
0
Mike Power Supply
On
0
(This feature is not
available in VN-V26U)
High
Audio File 1
Audio File 2
Audio File 3
Audio File 4
Audio File 5
—
—
—
—
—
Sense Up
x4(1/7.5s) (TV)
x2(1/7.5s) (TX)
Motion
ALC Priority
Shutter Speed
1/30(TV)
Auto(1/15 - 1/100)(TX)
Color
Easy Day and Night
VN-V25U,VN-X35U
only
B/W Mode
Color
VN-V26U, VN-V225U
series, VN-X235U series
only
EV Compensation
White Balance
0
ATW
Back Light Compensation Off
56
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is
applicable to VN-X series only.
Periodic FTP Time Filter
Unmask All
PrePostRecording Frame 15 fps(TV)
Rate
Ⅵ Alarm Page (A Page 30)
5 fps(TX)
Item
Factory Settings
PrePostRecording Before 5 sec
Trigger
Action
Disable
Input 1 Make
—
1st Trigger
PrePostRecording After
Trigger
5 sec
Max. Interval
2nd Trigger
Duration Output 1
Duration Output 2
Manual Output 1
Manual Output 2
1000 msec
1000 msec
Break
Disable
—
Action Position No.
(VN-X series only)
Break
Audio File
—
—
(This feature is not
available in VN-V25U)
Ⅵ PTZ Page (TX) (A Page 38)
Item
Factory Settings
Trigger Position No.
(VN-X series only)
Mode
None
Return Time
Zoom Limit
Speed
1
Mail Address
—
8
Mail Text
—
Moment
Attach Image
Off
TCP/UDP IP Address
TCP/UDP Port Number
TCP/UDP Data
Alarm Output Duration
Time Filter
—
Ⅵ Auto Patrol Page (TX) (A Page 39)
—
tem
Factory Settings
0 to 19
—
Position
—
Stay Time
Skip
Unmask All
Moving speed
Moment
Ⅵ Alarm Environment Page (A Page 34)
Ⅵ Privacy Mask Page (A Page 41)
Item
SMTP Server
Factory Settings
Item
Factory Settings
0.0.0.0
25
Mode
Masking Color Setting
Off
Port Number
16 (R, G, B)
Send Mail Address
POP before SMTP
POP Server
—
Off
Ⅵ Motion Detection Page (A Page 43)
0.0.0.0
110
—
Item
Factory Settings
Port Number
Detection
Level
Off
4
Username
—
FTP Server
Directory
0.0.0.0
—
Username
—
—
Periodic FTP
Off
Periodic FTP Interval
Periodic FTP Naming
1
Auto
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Item
Factory Settings
JPEG Destination
Address
225.0.1.1
List of Factory Settings of Each Page
(continued)
(TV) is applicable to VN-V series only. (TX) is
applicable to VN-X series only.
JPEG Destination Port
JPEG Frame Rate
49152
15 fps
MPEG4 Destination
Address
225.0.2.1
Ⅵ Network Basic Page (A Page 45)
Item
Factory Settings
DHCP Disable
192.168.0.2
255.255.255.0
0.0.0.0
Audio Destination
Address
225.0.3.1
IP Setting
IP Address
(This feature is not
Subnet Mask
Default Gateway
Host Name
Audio Destination Port
39152
(This feature is not
available in VN-V25U)
—
DNS Server
IP Protocol
0.0.0.0
Ⅵ Access Restrictions Page
(A Page 50)
IP version 4:On
IP version 6:Off
Item
Access Restrictions
IP Address
Factory Settings
IPv6 Address
Disable
deny
—
Ⅵ Network Details Page (A Page 46)
Item
JPEG TOS
Factory Settings
Ⅵ Time Page (A Page 52)
0
Item
Factory Settings
MPEG4 TOS
0
0
Off
Audio TOS
(This feature is not
available in VN-V25U)
NTP Server
Access Interval
Time Zone
0.0.0.0
hour, 1
(GMT) UTC
TTL( Unicast)
TTL( Multicast)
MTU
64
Ⅵ Password Page (A Page 53)
32
Item
Username
New Password
Factory Settings
1500
Auto
AadminB
Negotiation
Blank
Ⅵ Protocol Page (A Page 47)
Default passwords are:
AadminB : jvc
AoperatorB: jvc
Item
HTTP Server Port
VSIP Protocol
Factory Settings
80
AuserB
: jvc
Off
Ⅵ LED Settings Page (A Page 55)
VSIP Server Port
5510
On
Item
LED State
Identify Unit
Factory Settings
Enable
On
AMX Device Discovery
Protocol
Priority
client number
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous Page
This page is for acquiring information.
This page can be used during access using AadminB, AoperatorBand AuserB.
● Click [Advanced Settings] to display setting menu.
● Click [Miscellaneous].
A
Click
A Open Source
Press the [Show] button to display information of the software used by the
camera.
Software
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Operation Page
Displays the operating status of the camera.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [Operation].
A
B
C
Click
A Total Sending
Displays the total TCP/UDP bit rate sent by the camera as well as the
individual bit rates.
Bitrate
B Destination
C System Log
Displays the destination that the camera is sending data to.
Displays the following information.
● Number of seconds after startup
● Alarm information
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Settings Page (continued)
62
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Using Internet Explorer
Setting (continued)
Position List
(VN-X series only)
The Position List displays information on the preset positions.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [Position List].
Click
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Patrol Settings
(VN-X series only)
Patrol Settings displays the Auto Patrol information and settings.
This page can be used during access using AadminBor AoperatorB.
● Click [Advanced Settings] to display setting menu.
● Click [Patrol Settings].
Click
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
You can start up Built-in Viewer by entering the IP address in the Internet Explorer.
Built-in Viewer enables you to performing monitoring using JPEG or MPEG4 images, audio
transmission (This feature is not available in VN-V25U), and PTZ operations (TX).
Ⅵ Using the compressed JPEG format enables display of a series of still images as well as one-shot
recording of still images.
Ⅵ Using the compressed MPEG4 format enables display of MPEG4-encoded motion images.
Ⅵ You can send or receive audio using the JPEG/MPEG4 Viewer. (This feature is not available in VN-V25U)
ࡗ AScreen ConfigurationB(A Page 66) ࡗ Almage SettingsB(A Page 68) ࡗ APTZ SettingsB(A Page 70) ࡗ APTZ ControlB(A Page 72) ࡗ AJPEG Viewer SettingsB(A Page 74) ࡗ AMPEG4 Viewer SettingsB(A Page 76) ࡗ AAudio Monitor SettingsB(A Page 78) ࡗ AExiting the ViewerB(A Page 81) When the display or configuration of the opened screen appears strange, check
using the following procedures.
A Click [Start]-[Control Panel]-[Display] and open the [Display Properties] window
B Click the [Settings] tab in the [Display Properties] windows and click the [Advanced] button
C Check that [DPI setting] in the [General] tab has become [Normal size(96DPI)]
D Otherwise, change the setting to [Normal size(96DPI)] and reboot windows
Screen Configuration
A
B
C
D
E
F
G
H
I
operation menu
A MENU OFF/
For showing/hiding the operation menu.
Switches to the Control menu.
Click this button when you want to perform AImage SettingsBor APTZ
SettingsB(TX) or APTZ ControlB(TX)(A Page 74)
MENU ON
B Control
C Viewer Setup
Switches to the Viewer Setup menu
configure the settings of JPEG Viewer
or Operator Password
.
Click this button when you want to
A
B.
B
,
A
MPEG4 Viewer Audio MonitorB
B
,
A
A
66
Download from Www.Somanuals.com. All Manuals Search And Download.
D Stop/Play
E Capture
Pauses/Plays back images.
Captures the currently displayed image on the computer. The captured
data is recorded as a JPEG file in the folder that is created under [My
Document] of the computer. This is set to Amodel nameBby
default.(E.g., AVN-V225Bfolder is made for AVN-V225VPUB).The file
name is made up of the year, month, day, hour, minute, second, and
millisecond.
Memo:
● In the case of AWindows VistaB, images are stored under
[Documents].
● The folder name can be changed.(A Page 75)
Note:
● The time in the file name is based on the time on the PC clock, not
the time on the camera’s clock.
● Motion images cannot be captured.
● MPEG4 images cannot be captured.
F Speech
(This feature is not
available in VN-V25U)
Starts sending audio sound to the camera from the client PC. Only one
stream of audio sound can be sent for one unit of the camera You cannot
send audio sound from a client PC when transmission of audio sound
from a different client PC is in progress.
● The [Speech] button lights up in red during audio sound transmission.
● The [Speech] button does not turn red when audio transmission is
not possible.
Memo:
● Audio sound cannot be sent out simultaneously from the JPEG and
MPEG4 Viewers.
G Compression
H Display Size
Switches the stream to acquire.
You can specify either JPEG or MPEG4
For specifying the display size of the image area.
Fixed
:Display according to the window size of the browser.
Variable :Display according to the specified frame size.
Memo:
● The window size of the browser does not change when [Fixed] or
[Variable] is selected.
I Details
Starts up the page for configuring the various detailed settings.
Memo:
● The settings of Built-in Viewer are stored in the file named Cookie.
This setting screen is used to set Built-in Viewer as a software on the computer, and does not apply
to settings of the camera unit.
Searching and deleting cookie files
● Open [Tool]-[Internet Options]-[Advanced] of the Internet Explorer, and press the [Settings] button
under [Temporary Internet Files]. A new [Settings] will appear. Press the [View Files] button in this
window. The [Temporary Internet Files] window opens up and a list of files will be displayed. The file
named Acgi-binBin this list is the Cookie for the built-in viewer.
● Deleting this file deletes the viewer settings, and the viewer will be initialized during the next startup.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
(continued)
lmage Settings
Below are procedures for configuring the Image Settings.
● When a different menu is currently being displayed, click [Control] to switch the menu.
● Click each menu bar on the left of the screen to open the setting screen..
Ⅵ Image Settings
Click
A
B
C
D
A White Balance
For selecting the white balance control feature.
Mode
ATW
：Switches to the Auto-Tracking White Balance (automatic color
temperature tracking) mode. Adjusts the white balance automatically
according to the color temperature of the light.
AWC
：Switches to the Auto-White Balance Control mode. In the AWC mode,
values entered for the [AWC R-Gain] and [AWC B-Gain] items under
White Balance of the Camera page are applied to white balance.
[AWC] Button
Executes AWC (automatic white balance control).Execute by placing a white
object around the center of the screen in a location with a lighting condition
that is similar to the object to be shot.
Click [AWC] button to switch to AWC mode.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
BBack Light
Compensation
For selecting the backlight compensation feature. Set this feature when there
is a bright light source in the same direction as the object. Enables unwanted
light sources to be excluded from the photometry area.
Mode
Off
Area1 to 4
: Disables backlight compensation.
For selecting a photometry area from the four available types.
:
Photometry
Area
Photometry
Area
Photometry
Area
Photometry
Area
Photometry
Area
Off
Area1
Area2
Area3
Area4
Memo:
● The backlight compensation area is not linked to digital PTZ (TX).
[Set values: Off, Area1, Area2, Area3, Area4]
B
Easy Day and Night For specifying Easy Day and Night.
VN-V25U, VN-X35U only
Mode
Color
: Sets to the color mode at all times.
Black and White : Sets to the black-and-white mode at all times.
Auto
: Image color switches to black-and-white when the
luminance level is low.
Memo:
●
The threshold of the Auto switching cannot be changed.
[Set values : Color , Black and White, Auto]
CB&W Mode
For specifying whether to switch the image to the B&W mode. Auto mode can
be specified for switching automatically to the Black and White mode when
the luminance level is low. In auto mode one of three levels can be selected
according to the luminance level.
VN-V26U, VN-V225U
series, VN-X235U
series only
Mode
Color
: Switches to the color mode at all times.
Black and White : Switches to the black-and-white mode at all times.
Auto Low
Auto Mid
Auto High
: Switches to the black-and-white mode when the
luminance of the signal level of the object is low.
: Switches to the black-and-white mode when the
luminance of the signal level of the object is medium.
: Switches to the black-and-white mode when the
luminance of the signal level of the object is high.
[Set values : Color, Black and White, Auto Low, Auto Mid,Auto High ]
Memo:
●
●
●
The infrared filter engages and disengages when switching between modes,
which causes mechanism noise.
During the occurrence of mechanism noise, the distribution sound from the
camera will be muted. (VN-V26U only)
When
A
Auto Low
B
,
A
Auto Mid
B
or AAuto HighBhas been selected the camera
will change the mode immediately according to the luminance level.
C Focus Assist
If [Execute] button is clicked, [Current State] will change to [Focus Assist] and focus
assist mode is enabled. If [Stop] button is clicked, [Current State] will change to
[Normal] and focus assist mode is disabled.
Mode
Memo:
●
Focus assist mode will be disabled after 3 minutes if left unattended.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
(continued)
PTZ Settings
(VN-X series only)
This page describes procedures for setting the preset positions.
● This page can be used during access using AadminBor AoperatorB.
To access this setting, you need to set the password of AoperatorB authority.
(A Page 80)
● When a different menu is currently being displayed, click [Control] to switch the menu.
● Click the menu bar on the left side of the screen to open the setting screen.
Ⅵ PTZ Settings
Click
A
B
C
70
Download from Www.Somanuals.com. All Manuals Search And Download.
A Preset Position
For setting the preset positions.
Position
For selecting a APositionB.
[Set values :HOME , 1 to 19]
Title
Displays the current title.
Enter accordingly if you want to register or change a title.
(You can enter up to 32 alphanumeric or 16 Japanese characters. AJPEG
ViewerBdisplays up to only 16 alphanumeric or 8 Japanese characters.
Press [Register] button to complete position registration.
Memo:
● Click the [Unregister] button to delete the selected position information.
However, [HOME] cannot be deleted.
● The display area of Home position is set to the full screen by default.
B Pan /Tilt /Zoom
Ⅵ Pan/Tilt operation
Click the arrow buttons to move the display area in the direction indicated
by the arrow. Release the button to stop moving the area.
Click the AHBbutton to move to the home position.
Ⅵ
Zoom operation
Use this function to perform digital zoom on the display area.
[ + ]
[ - ]
: Zooms toward the tele end, and display of the object is enlarged.
: Zooms toward the wide end, and display of the object becomes
smaller.
Ⅵ Ratio to Full Area
Shows current ratio to full area.
Memo:
● You can restrict the magnification of the object using the [+] button by
altering the [Zoom Limit] settings. (A Page 38)
C Speed
For configuring the operation speed settings.
Pan/Tilt
:
For configuring the operation speed settings of the Pan/Tilt control
button. The larger the value, the higher the operation speed.
[Set values: 1 to 8]
Zoom : For configuring the operation speed settings of the Zoom control
button. The larger the value, the higher the operation speed.
[Set values: 1 to 4]
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
(continued)
PTZ Control
(VN-X series only)
Use this item to operate the PTZ feature. Settings can be configured on the PTZ Settings .
(A Page 70)
● This page can be used during access using AadminBor AoperatorB.
To access this setting, you need to set the password of AoperatorB authority.
(A Page 80)
● When a different menu is currently being displayed, click [Control] to switch the menu.
● Click each menu bar on the left of the screen to open the setting screen.
Ⅵ PTZ Control
Click
A
B
C
D
72
Download from Www.Somanuals.com. All Manuals Search And Download.
A AUTO
FUNCTION
Start : Starts the Auto Patrol operation.
Stop : Stops the Auto Patrol operation that is currently running.
B Preset
For selecting a Preset Position, or move to the selected Position if that Position
has already been registered.
Position
[Set values : HOME , 1 to 19]
C Pan/Tilt/
Ⅵ Pan/Tilt operation
Zoom
Click the arrow buttons to move the display area in the direction indicated by
the arrow. Release the button to stop moving the area.
Click the [H] button to move to the home position.
Ⅵ Zoom operation
Use this function to perform digital zoom on the display area.
[ + ]
[ - ]
: Zooms toward the tele end, and display of the object is enlarged.
: Zooms toward the wide end, and display of the object becomes
smaller.
Ⅵ Ratio to Full Area
Shows current ratio to full area.
Memo:
● You can restrict the magnification of the object using the [+] button by
altering the [Zoom Limit] settings.(A Page 38)
D Speed
For configuring the operation speed settings.
Pan/Tilt : For configuring the operation speed settings of the APan/TiltBcontrol
button. The larger the value, the higher the operation speed.
[Set values : 1 to 8]
Zoom : For configuring the operation speed settings of the AZoomBcontrol
button. The larger the value, the higher the operation speed.
[Set values : 1 to 4]
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
(continued)
JPEG Viewer Settings
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
Using the compressed JPEG format enables display of a series of still images as well as one-shot recording
of still images.
When the JPEG Viewer is first installed, it is set to play back at 15 fps (TV) or 5 fps (TX) by default.
● When a different menu is currently being displayed, click [Viewer Setup] to switch the menu.
● Click the menu bar on the left side of the screen to open the respective setting screens.
● Click the [Apply] button to activate the settings in the Viewer. The settings will be saved on the
computer.
Ⅵ On Screen Display
Ⅵ Stream
Ⅵ Other
Click
Click
Click
Settings
A
A
B
C
A
B
C
D
D
E
E
Ⅵ On Screen Display
For setting display items on the viewer screen.
For the JPEG Viewer, characters are displayed as overlay on the video image.
Settings
A Camera ID
Select On to display [Camera ID].
A
B
[Camera ID] can be specified on the[Basic Settings2] or [Camera] page of the
camera. ( Page 21)
A
B Position Title Selecting
(TX)
AOn
B
displays the position title.
C Disp MD
When
A
On
B
is selected, the frame of the video image display area where motion
is detected turns red.
D Time
Select AOnBto display the time.
This indicates the time that is stored in the JPEG data.
E Format
Select the format for displaying time.
YYYY, MM, and DD denote year, month and day respectively, while HH,
MM, and SS denote hour, minute and second respectively. mm is
equivalent to 1/100 seconds.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
Ⅵ Stream Settings
A Stream
For specifying settings for receiving JPEG stream.
For selecting the protocol when the viewer acquires data from the
camera. When AHTTPBis selected, lost packets are recovered via
resending. Camera may be monitored using multiple viewers when
AMulticastBis selected.
When playing back via multicast, start multicast sending on the
[Streaming] page. (A Page 48)
Note:
● When the built-in viewer is launched with AMulticastBspecified, a
Windows firewall warning may appear. In this case, select AunblockB
and proceed.
● If AblockBis selected, the Windows firewall will block the multicast
stream and playback of multicast by the viewer will fail.
B HTTP Port
C Frame Rate
You can change the HTTP port number.
The default port number setting is 80.
Specify the same value as the parameter that is set on the Protocol page
of the camera. (A Page 47)
For selecting the acquisition frame rate of the viewer.
Selecting a large frame rate will increase the processing load of the
computer on which the viewer is running.
[Set values : 30 (TV), 25(TV) , 15 , 10 , 7.5 , 6 , 5 , 3 , 2 , 1 , 1/2 , 1/3 ,
1/5 , 1/10 , 1/15 , 1/20 , 1/30 , 1/60]
Note:
● Set to a rate such that the CPU burden of the computer does not
function properly.
D Multicast IP
You can change the multicast IP address.
The default address is 225.0.1.1.
Address
E Multicast Port You can change the multicast port number.
The default port number setting is 49152.
This is enabled when AStartBis selected for the [JPEG Control] item on
the[Control] page.
Specify the same value as the parameter that is set on the [Streaming]
page of the camera. (A Page 48)
Ⅵ Other
A Folder Name
For specifying the name of the folder in which the captured files are
stored. (Default name when viewer is installed: Amodel nameB
(E.g., AVN-V225Bfolder is made for AVN-V225VPUB)
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
(continued)
MPEG4 Viewer Settings
Using the compressed MPEG4 format enables display of MPEG4-encoded motion images.
● When a different menu is currently being displayed, click [Viewer Setup] to switch the menu.
● Click the menu bar on the left side of the screen to open the respective setting screens.
● Click the [Apply] button to activate the settings in the Viewer. The settings will be saved on the
computer.
Memo:
● To make use of the built-in MPEG4 Viewer of the camera, you will need to install the ffdshow open
source codec. You can obtain ffdshow through the Internet.
Ⅵ Title Bar
Ⅵ Stream
Click
Click
A
B
C
A
B
C
D
D
76
Download from Www.Somanuals.com. All Manuals Search And Download.
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
Ⅵ Title Bar
For setting display items on the viewer screen.
For the MPEG4 Viewer, characters are displayed in the title bar of the
window.
A Camera ID
Select AOnBto display [Camera ID].
[Camera ID] can be specified on the [Basic Settings1] or [Camera] page
of the camera.
(A Page 21)
B Position Title Selecting AOnBdisplays the Position Title.
(TX)
C Time
Select AOnB to display the time.
D Format
Select the format for displaying time.
YYYY, MM, and DD denote year, month and day respectively, while HH,
MM, and SS denote hour, minute and second respectively. mm is
equivalent to 1/100 seconds.
Ⅵ Stream Settings
A Stream
For specifying settings for receiving MPEG4 stream.
For selecting the protocol when the viewer acquires data from the
camera.
When AHTTPB is selected, lost packets are recovered via resending.
Camera may be monitored using multiple viewers when
AMulticastB is selected.
When playing back via multicast., start multicast sending on the
[Streaming] page of the camera unit.
Note:
● When the built-in viewer is launched with AMulticastB specified, a
Windows firewall warning may appear. In this case, select AunblockB
and proceed.
● If AblockB is selected, the Windows firewall will block the multicast
stream and playback of multicast by the viewer will fail.
B HTTP Port
You can change the HTTP port number.
The default port number setting is 80.
Specify the same value as the parameter that is set on the [Protocol]
page of the camera. (A Page 47)
C Multicast IP
You can change the multicast IP address.
The default address is 225.0.2.1.
Address
D Multicast Port You can change the multicast port number.
The default port number setting is 59152.
This is enabled when [Start] is selected for the [MPEG4 Control] item on
the [Streaming] page.
Specify the same value as the parameter that is set on the [Streaming]
page of the camera. (A Page 48)
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
(continued)
Audio Monitor Settings
(This feature is not available in VN-V25U)
This page describes procedures for configuring the settings to send/receive audio sound using the
JPEG and MPEG4 Viewers.
● This page can be used during access using AadminBor AoperatorB.
To access this setting, you need to set the password of AoperatorB authority.
(A Page 80)
● When a different menu is currently being displayed, click [Viewer Setup] to switch the menu.
● Click the menu bar on the left side of the screen to open the respective setting screens.
● Click the [Apply] button to activate the settings in the Viewer. The settings will be saved on the
computer.
Ⅵ Speech
Ⅵ Common
Ⅵ Receive
Click
Click
Click
A
B
C
A
A
D
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅵ Receive
A Receive
For specifying settings related to receiving of audio sound sent from the
camera.
For specifying whether to receive audio sound. Select AOnBto receive
audio sound.
B Stream
For selecting the stream format of the received audio sound.
When AHTTPBis selected, lost packets are recovered via resending. When
AMulticastBis selected, you can monitor the audio sound of the camera
using a multiple number of client PCs. During receiving via multicast., start
multicast sending on the [Streaming] page. (A Page 48)
Note:
●When the built-in viewer is launched with AMulticastBspecified, a
Windows firewall warning may appear. In this case, select AunblockBand
proceed.
stream and playback of multicast by the viewer will fail.
C Multicast IP
You can change the multicast IP address.
The default address is 225.0.3.1.
Address
Specify the same value as the parameter that is set on the [Streaming]
page of the camera. (A Page 48)
D Multicast Port You can change the multicast port number.
The default port number setting is 39152.
Specify the same value as the parameter that is set on the [Streaming]
page of the camera. (A Page 48)
Ⅵ Speech
A Destination
computer.
You can change the destination port for sending audio sound to the camera
from the computer. The default port number setting is 49298
Port
Ⅵ Common
For specifying the HTTP port settings
A HTTP Port
For changing the port number during access to the camera from the client
PC via HTTP.
The default port number is 80.
Specify the same value as the parameter that is set on the Protocol.
(A Page 47)
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation of Built-in Viewer
(continued)
Operator Password
(TV) is applicable to VN-V series only. (TX) is applicable to VN-X series only.
Follow the procedures below to configure the operator password required for sending/receiving audio
sound or PTZ operation.
● This page can be used during access using AadminBor AoperatorB.
● When a different menu is currently being displayed, click [Viewer Setup] to switch the menu.
● Click the menu bar on the left side of the screen to open the setting screen.
● Click the [Apply] button to activate the settings in the Viewer. The settings will be saved on the
computer.
Click
A
A Operator Password Ⅵ Follow the procedures below to configure the operator password
required for sending/receiving audio sound (This feature is not available
in VN-V25U) or PTZ operation (TX).
Enter the password of “operator” authority. Enter the password that is set
on the Password Page. (A Page 53)
Operator
Password
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Exiting the Viewer
To exit, press the [
ן ] button at the top right of the window. Click]
Memo:
● During the next startup of the built-in viewer, launch the Internet Explorer and enter the URL of the
built-in viewer in the address field.
For example, if the IP address of the camera is 192.168.0.2, enter as follows:
● After the [Security Settings] screen appears, press the [OK] button to proceed.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting
Reference
Page
Symptom
Causes and Countermeasures
IP address of the camera is
unknown
●
●
The default IP address is 192.168.0.2, and the
default subnet mask is 255.255.255.0.
When [IP Setting] is set to ADHCP EnableBand
A Page 17
there is no DHCP sever, the camera will run using
the default IP address when it is started up.
If there is a PC in the same LAN, you can search
cameras from the PC using the search tool.
●
A Page 10
A Page 8
The web page of the camera Check the Internet Explorer settings. When a proxy
cannot be displayed
server is in use, configure the proxy server settings
of the Internet Explorer accordingly.
The built-in viewer cannot be Check the Internet Explorer settings. The built-in
A Page 8
installed
viewer consists of a software component called
ActiveX. The ActiveX is usually installed when the
built-in viewer is used for the first time. However,
installation may be rejected depending on the Anti-
virus software settings. In this case, change the
settings of the Anti-virus software before installing
the built-in viewer.
Authentication by Verisign
VeriSign’s electronic signature is stored in the built-
—
—
appears during installation of in viewer.
the built-in viewer
For computers with a network environment that is
connected to the Internet, the authenticity of the
viewer can be verified via authentication by
VeriSign.
A warning message appears
upon starting up the built-in
viewer
The built-in viewer consists of a software
component called ActiveX.
The ActiveX is usually installed when the built-in
viewer is used for the first time. However, installation
may be rejected depending on the Anti-virus software
settings. In this case, change the settings of the Anti-
virus software before installing the built-in viewer.
TCP images cannot be
played back
● Number of streams is limited based on settings
and client request. Multicast is available for more
receivers.
A Page 3
A Page 47
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Page
Symptom
Causes and Countermeasures
Multicast images cannot be
played back
● Start multicast transmission manually from the
[Streaming] page of the camera.
● In the case of multicast reception at the built-in
viewer, check that the multicast address and port
number of the built-in viewer settings coincide
with those on the [Streaming] page of the
camera.
A Page 48
A Page 74
Make use of a network that supports IGMPv2 for
multicast transmission.
● Multicast may be blocked by the Windows XP
firewall. When this occurs, perform the following
to allow it to pass through.
A Page 66
Double-click [Windows Firewall] under [Start]-
[Control Panel], click the [Add Port…] button
under the Exception tab, and register the port
number to be allowed through the firewall in the
Port Number field. Enter an arbitrary character
string in the name field.
The frame rate of the
displayed image is low
● Check the built-in viewer settings when a built-in
viewer is in use.
● Frame rate will be constrained when the network
bandwidth is narrow.
● When the image distribution setting is set to the
Aclient numberBmode and there is an increase
in distribution request, images will be distributed
at a frame rate lower than the specified frame
rate.
A Page 66
A Page 75
A Page 47
A white zone appears in the
built-in viewer
● For some computers, a part of the Internet
Explorer graphics may not appear and is left
white when the following setting is performed on
the Internet Explorer.
If [Right-click on the Desktop screen]-
[Properties]-[Settings]-[Advanced]-
[Advanced]-[DPI setting] is set to ALarge sizeB
or ACustom sizeB, select ANormal sizeBto
resume normal drawing.
—
—
Unable to receive alarm
notification using the
computer via TCP/UDP
● Data may be blocked by the WindowsXP firewall.
When this occurs, perform the following to allow
it to pass through.
Double-click [Windows Firewall] under [Start]-
[Control Panel], click the [Add Port…] button
under the Exception tab, and register the port
number to be allowed through the firewall in the
Port Number field. Enter an arbitrary character
string in the name field.
Images are not distributed to
the network
● Check whether the [MONITOR OUT] selector
switch on this camera is set to ANTSCBor
APALB, ANBor APB. If either of the above is
selected, change the [MONITOR OUT] selector
switch setting to AOFFB. After changing the
switch settings, press the [RESET] button to
reboot.
INSTRUCTIONS
(Installation)
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Troubleshooting (continued)
Reference
Page
Symptom
Causes and Countermeasures
The MPEG4 Viewer screen
appears in black
When DirectX 9.x or Windows Media Player 9.x is
installed on the computer, the video image screen
appears in black.
—
[Countermeasure]
To make use of the built-in MPEG4 Viewer of the
camera, install “ffdshow” that is open source codec.
You can download “ffdshow” from the Internet.
No MONITOR OUT image
output
● Set the [MONITOR OUT] selector switch to
ANTSCBor APALB, ANBor APBand press the
Reset button.
INSTRUCTIONS
(Installation)
● When using the [MONITOR OUT] output, set the
privacy mask to AOffB.
A Page 41
A Page 41
Zonal noise occurs at the
When using the [MONITOR OUT] output, set the
bottom of the MONITOR OUT privacy mask to AOffB.
image
Images from the network are Set the [MONITOR OUT] selector switch to AOFFB,
INSTRUCTIONS
(Installation)
distorted
and press the Reset button.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
LST0886-001A
© 2009 Victor Company of Japan, Limited
Download from Www.Somanuals.com. All Manuals Search And Download.
|