Projection Television Users Guide
For Model:
HD-58S998
Illustration of HD-58S998 and RM-C1400
Important Note:
In the spaces below, enter the model and serial number of your television (located
at the rear of the television cabinet). Staple your sales receipt or invoice to the
inside cover of this guide. Keep this user’s guide in a convenient place for future
reference. Keep the carton and original packaging for future use.
Model Number:
LCT2172-001B-A
1106TNH-II-IM
Serial Number:
Download from Www.Somanuals.com. All Manuals Search And Download.
®
• As an “ENERGY STAR ” partner,
JVC has determined that this
product or product model meets the
®
“ENERGY STAR ” guidelines for energy
efficiency.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
16) Avoid improper installation and never position the unit where good ventilation is impossible. When
installing this TV, distance recommendations must be maintained between the set and the wall,
as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance
guidelines shown for safe operation.
200 mm
200 mm
150 mm
150 mm
17) Cautions for installation
— Do not tilt the TV towards the left or right, or towards the back.
— Install the TV in a corner on the floor so as to keep cords out of the way.
— The TV will generate a slight amount of heat during operation. Ensure that sufficient space is
available around the TV to allow satisfactory cooling.
18) Make enough room for inserting and removing the power plug. Place the TV as close to the
outlet as possible. The main power supply for this TV is controlled by inserting or removing the
power plug.
FCC Notice:
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Caution – This television model HD-58S998 is for use only with JVC Model RK-CSLM8 stand
and JVC Model TS-CP01WG wall mounting bracket. Use with other stands or wall mounting
brackets are capable of resulting in instability causing possible injury.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
We have an important note for customers who subscribe to basic cable services (do not have
a separate cable box) and plan to use their JVC TV remote control to select channels.
Once you run the Auto Tuner Setup (which detects and programs all the channels your TV is
receiving through the RF input), every channel number available from your cable company
will appear in your television’s Channel Summary and they will all be marked as available for
scanning. Even though every channel is detected and appears as available, you will only be
able to view those that you specifically subscribe to from your cable company. This will likely
mean there are blank channels between those channels you wish to scan or “surf”.
We apologize for any inconvenience this may cause but it is important to note that this is
not a malfunction of your television. If you want to sequentially scan those channels you
subscribe to without blank ones in between, you can contact your cable company for their
cable box and remote.
Caring for the Cabinet
Normally, light dusting with a soft, non-scratching duster will keep your TV clean.
If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly
moistened with water. You can add a few drops of mild liquid detergent to the water to help
remove spots of oily dirt.
• DO NOT allow liquid to enter the TV through the ventilation slots.
• DO NOT use strong or abrasive cleaners on the TV.
• DO NOT spray liquids or cleaners directly on the TV’s surface.
• DO NOT rub or scrub the TV harshly. Wipe the set gently with a soft cloth.
Caring for the Screen
The screen is treated with an electrostatic-proof coating. When it gets dirty, wipe it gently with a
soft cloth. If the screen is very dirty, wipe it down with a cloth dipped in a diluted kitchen cleaner
and thoroughly wrung-out. Then wipe immediately after with a clean, dry cloth.
Do not apply alcohol, organic solvents (like acetone), acidic or alkaline cleansers to the screen.
These will remove the coating layer and cause discolorations.
Do not push or hit the screen. This could cause scratches on the screen surface and image
distortions.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Thank you for purchasing a JVC HDTV-ready projection television which uses the high-quality
HD-ILA projection system. This is one of the highest quality and most technologically advanced
televisions available today. It is recommended that you read this instruction manual before using
your television in order to learn about it’s many features. Cautions related to the safe use of the
device and important information which will help you to be able to use this device for a long time
is in the Appendix. Once again, thank you for purchasing this television and please enjoy using
it.
In order to use the television for a long time
This television uses a lamp to project the picture onto the screen. Before using this television,
please read the safety cautions and information about this television which are summarized
below.
1. When the power is turned on, the warming up commences
This television uses a lamp to project the picture onto the screen. Once the lamp has warmed
up, you can enjoy the pictures at their full brightness. What happens when the power is turned
on is explained below. Immediately after the power is turned on, since the lamp has not had
time to warm up, the picture is displayed only dimly on the screen. As the lamp warms up, the
picture becomes brighter. It takes approximately one minute for the lamp to warm up to it’s
normal operating temperature. There are 2 LED indicators on the front panel of the television
that can be used as a guide. When the POWER button is pressed, the LAMP LED indicator
blinks in orange for approximately 1 minute at approximately every 2 seconds, and then goes
out.
Note: It is impossible to turn the power off during this period. After 1 or more minutes have
passed, you can turn off the power.
2. Cooling the inside of the television and the lamp
Cooling is also performed while the television is being shut down.
When the POWER button is pressed to turn off the power, the following operations are
performed. When the television is turned off, the screen transitions to dark like a curtain from
top to bottom. Then, cooling is performed for approximately 40 seconds. When the cooling is
being performed, the LAMP LED indicator on the front panel blinks in orange at approximately
every 3 seconds. The television can not be operated while the cooling is being performed.
After the cooling has been performed for 40 seconds, the power is turned off. Do not remove
the electrical plug until after the cooling process has completed. If the electrical plug is
removed before the cooling process has completed, the internal circuits and lamp may overheat
leading to the life of the lamp being shortened and the possibility of malfunctions.
Do not block the ventilation holes.
Do not block the ventilation holes while the power is turned on. Do not block the air intake holes
behind the speaker grills.
3. The lamp is a consumable item
Replace the lamp when it has blown or when the picture becomes dark. The lamp is a user
replaceable item. The lamp must be recycled. For a detailed explanation on how to recycle the
lamp, refer to the Appendix and the instructions that are included with the replacement lamp kit.
The life of the lamp changes depending on the atmospheric temperature and altitude in which
the TV is being used.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
4. The television requires a lot of electrical power
It is recommended that the television is connected directly to the wall socket, and not to another
device. When connecting the television to a wall socket that is being used by another device, or
when using an extension cord, be careful not to exceed the electrical capacity of the socket.
Do not turn the power on and off repeatedly in a short amount of time.
It subjects the television and the lamp to stress and may lead to malfunctions and the life of the
lamp being shortened.
5. The screen is made of plastic
Handle the screen very carefully as it can scratch easily. Do not rub, hit or press on it with any
hard objects. When the screen is dirty, gently wipe it with a soft cloth. Refer to the Appendix for
details on how to clean the screen.
6. Caution! Warm air from the air ducts
This unit has an air duct for cooling. The duct will blow warm air while the television is operating.
When placing the television, make sure not to locate it too close to wallpaper. The warm air
could cause the color of the wallpaper to change. Also, take care to keep children and pets
away from the warm air ducts. Long exposure to the warm air from the ducts could cause a
minor burn.
7. Caution! Moving this television
When lifting this television, Do not hold by the screen. Holding the screen could cause it to
detach, causing the television to fall.
8. Do not replace the lamp immediately after use
The lamp becomes extremely hot during use. If the lamp is touched immediately after use
before it has a chance to cool down, there is a danger of burns. Be careful when handling the
lamp.
9. Do not touch the lamp glass
If the lamp is used when there is dirt from fingers on the lamp glass, there is a possibility of the
lamp breaking. Be careful not to touch the lamp glass.
10. ILA element characteristics
Do not project still pictures or pictures that have still segments for a long period of time. The still
parts of the picture may remain on the screen. This is a characteristic of ILA elements and not a
malfunction. The picture will disappear over time.
11. Condensation
When a heater is turned on or the television is moved from a cold place to a hot place, droplets
of water may form on the lamp and screen. This is called condensation. If the television is used
while this condensation is still present, the picture may seem distorted, and the inside of the
screen may become dirty. In this case, wait until the condensation has gone before using the
television.
12. Do not open the cabinet of this television
This television has a HDMI terminal. Opening up the cabinet will violate the copyright of the
program or software shown on the television. Please do not open the cabinet.
13. Usable Time
Do not keep the TV on for more than 24 hours consecutively. There is a possibility of the life of
the lamp being shortened.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
The TV comes with front and rear pedestal (included). If you choose to mount the TV to a
wall or utilize JVC optional (sold separately) TV stand model RK-CSLM8, or wall mounting kit
TS-CP01WG, you will not need the pedestal but should keep it for possible future use.
If you do not utilize TV stand model RK-CSLM8, the front and rear pedestal MUST be attached
to prevent injury. If the TV sits flush against the wall, only the front pedestal MUST be attached.
To attach the front and rear pedestal.
1) Clear a flat, soft area on which to lay the TV on it's back. Two
people can gently lay back the TV. Please use extra care as
any shock or impact may damage the TV. (Do not lay it on it's
front to avoid damaging the screen.)
2) Remove the front pedestal from its box and
place it over the screw holes on the bottom
of the TV. All the holes should match up
perfectly. Tighten 8 Phillips type screws
(included) into the holes marked.
3) Gently return the TV to an upright position. Please attach the
rear pedestal after you attach the front pedestal. If you attach
the rear pedestal first, you may break the pedestal when you
attach the front pedestal.
Note:
• If the TV sits flush against the wall, you do not need to attach the rear pedestal.
4) Remove rear pedestal from it's box and slide the rear pedestal
as shown, under the TV and into the proper position.
5) Remove the cover on the rear pedestal towards the upper part.
6) Tighten 6 Phillips type screws (included) into the holes.
7) Attach the cover again.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Button Functions . . . . . . . . . . 59
Power . . . . . . . . . . . . . . . 59
Number Buttons . . . . . . . . . . 59
Tune . . . . . . . . . . . . . . . 59
Channel +/- . . . . . . . . . . . . . 59
Volume +/- . . . . . . . . . . . . . 59
Muting . . . . . . . . . . . . . . 59
D/A (Digital/Analog) . . . . . . . . 60
Mode . . . . . . . . . . . . . . 60
Input . . . . . . . . . . . . . . . 60
Return+/TV . . . . . . . . . . . . 61
Light . . . . . . . . . . . . . . . 61
Menu . . . . . . . . . . . . . . . 61
OK . . . . . . . . . . . . . . . . 61
Back . . . . . . . . . . . . . . . 61
Favorite . . . . . . . . . . . . . 62
Aspect . . . . . . . . . . . . . 63
Important Safety Precautions . . 2
Warnings . . . . . . . . . . . . . . . 5
Quick Setup . . . . . . . . . . . . . . 10
Unpacking your TV . . . . . . . . . . . . 10
TV Model . . . . . . . . . . . . . . . . 11
TV Remote Control . . . . . . . . . . . 12
Getting Started . . . . . . . . . . . . . 13
The Remote Control . . . . . . . . . . 13
Connecting Your Devices . . . . . . . 15
Interactive Plug In Menu . . . . . . . . 24
Onscreen Menus . . . . . . . . . 27
Using the Guide . . . . . . . . . . . . . 27
Onscreen Menu System . . . . . . . . . 28
Auto Tuner Setup . . . . . . . . . . . . 30
Channel Summary . . . . . . . . . . . . 31
Channel Label . . . . . . . . . . . . . 32
V-Chip . . . . . . . . . . . . . . . . . . 33
Set Lock Code . . . . . . . . . . . . . 39
Language . . . . . . . . . . . . . . . . 40
Closed Caption . . . . . . . . . . . . . 40
Auto Shut Off . . . . . . . . . . . . . . 43
XDS ID . . . . . . . . . . . . . . . . . 43
Noise Muting . . . . . . . . . . . . . . 43
Front Panel Lock . . . . . . . . . . . . 44
V3 Smart Input . . . . . . . . . . . . 44
Video Input Label . . . . . . . . . . 45
Position Adjustment . . . . . . . . . . . 46
Power Indicator . . . . . . . . . . . . . 46
HDMI Size . . . . . . . . . . . . . . . 47
Video-1 Audio . . . . . . . . . . . 47
Digital Setup . . . . . . . . . . . . . 48
Antenna Level . . . . . . . . . . . . 48
Digital Sound . . . . . . . . . . . . . . 49
Software Version . . . . . . . . . . . . 49
Software Update . . . . . . . . . . . . 50
Picture Settings . . . . . . . . . . . . . 51
Color Temperature . . . . . . . . . . . . 51
Color Management . . . . . . . . . . . . 52
Dynamic Gamma . . . . . . . . . . . . . 52
Advanced Smart Picture . . . . . . . . 52
Natural Cinema . . . . . . . . . . . . . 53
Digital VNR . . . . . . . . . . . . . . . . 53
MPEG NR . . . . . . . . . . . . . . . 54
Reset . . . . . . . . . . . . . . . . . . 54
Sound Settings . . . . . . . . . . . . . 55
Turn On Volume . . . . . . . . . . . . . 55
Volume Limit . . . . . . . . . . . . . . 55
Reset . . . . . . . . . . . . . . . . . . 55
Set Clock . . . . . . . . . . . . . . . . 56
On/Off Timer . . . . . . . . . . . . . . . 57
Lamp Timer Reset . . . . . . . . . . . . . 58
Aspect Ratios
.
.
.
.
.
.
.
.
.
.
63
Guide . . . . . . . . . . . . . . . 64
Sound . . . . . . . . . . . . . . . 65
Sub Channel . . . . . . . . . . . . . 65
Video Status . . . . . . . . . . . . 66
C.C. . . . . . . . . . . . . . . . . 66
Sleep Timer . . . . . . . . . . . . . 67
ML/MTS . . . . . . . . . . . . . . . 67
Twin . . . . . . . . . . . . . . . . . 68
Swap . . . . . . . . . . . . . . . . 68
Select . . . . . . . . . . . . . . . . 69
Freeze . . . . . . . . . . . . . . . 69
Display . . . . . . . . . . . . . . . 69
External device control buttons . . . . 69
Remote Programming . . . . . . . . 70
Programming Codes . . . . . . . . 70
OSD Information . . . . . . . . . . 76
Lamp Replacement . . . . . . . 77
Troubleshooting . . . . . . . . . . 81
Specifications . . . . . . . . . . 83
Warranty . . . . . . . . . . . . . 84
Authorized Service Center . . . 85
Notes . . . . . . . . . . . . . . 86
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Unpacking your TV
Thank you for your purchase of a JVC Color Television. Before you begin setting up your new
television, please check to make sure you have all of the following items. In addition to this
guide, your television box should include:
AA
Batteries x 2
Remote Control x 1
Television x 1
POWER
D/A
TV
STB VCR DVD AUDIO
INPUT
MODE
V1
V2
V3
V4
V5
1
2
5
8
0
3
6
9
4
7
RETURN
TV
+
TUNE
–
CH
+
–
VOL
+
LIGHT
MUTING
OK
Note: Your television
and/or remote
DVR
STATUS
VIDEO
SOUND
GUIDE
SUB CH
TV/VCR
C.C.
SUB T.
DISPLAY
control may differ
from the examples
illustrated here.
TWIN
SLEEP
ML/MTS
FREEZE
SWAP
SELECT
RTM-CV1400
Front Pedestal x 1
Rear Pedestal x 1
Philips type screws x 14
Warning:
• If you choose to mount the TV to a wall or utilize JVC optional (sold separately) TV stand
model RK-CSLM8 or wall mounting kit TS-CP01WG, you will not need the pedestal, but
should keep it for future use.
• If you do not utilize TV stand model RK-CSLM8, the front and rear pedestal MUST be
attached to prevent injury.
• If the TV sits flush against the wall, only the front pedestal MUST be attached.
We recommend that before you start using your new television, you read this entire User’s
Guide so you can learn about your new television’s many great features. If you’re anxious to
start using your television right away, a quick setup guide follows on the next few pages.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
TV Model
Before you connect your television to another device, please refer to the proper diagrams for
your specific TV and remote. These will help assist you in understanding how to connect your
television to another device, as well as use the remote to set up your television.
Side Panel Diagram
Facing the front of the TV, these connections are located behind the door on the right side.
LICENSED UNDER THE
SERVICE
ONLY
OPTICAL OUT
Digital Audio
FOLLOWING U.S. PATENTS
6,183,091
DIGITAL-IN
6,419,362
INPUT- 2
INPUT-1
75Ω
(VHF/UHF)
INPUT-3
INPUT-4
VIDEO
S-VIDEO
OVER
AUDIO
OUTPUT
AUDIO IN
Y
Y
VIDEO
PB
PR
L
L
PB
PR
L
L
AUDIO
AUDIO
R
R
R
R
Note:
• The terminal labeled "SERVICE ONLY", is exclusively used to update the software version.
Front Panel Diagram
This terminal is located under the front panel door. To access, push the † arrow on the door to
open.
LAMP LED
POWER LED
LAMP
POWER button
INPUT-5
CHANNEL VOLUME
+
+
INPUT
MENU
VIDEO L/MONO
PC IN
R
–
–
AUDIO
OPERATE
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Remote Control
POWER
D/A
TV
STB VCR DVD AUDIO
INPUT
MODE
V1
V2
V3
V4
V5
1
2
5
8
0
3
6
9
4
7
RETURN +
TV
TUNE
– CH +
– VOL +
LIGHT
MUTING
OK
DVR
STATUS
SOUND
VIDEO
GUIDE
SUB CH
TV/VCR
C.C.
SUB T.
DISPLAY
TWIN
SLEEP
ML/MTS
SWAP
SELECT
FREEZE
RTM-CV1400
RM-C1400
• For information on remote control buttons, see pages 59 - 69.
• SUB CHANNEL and GUIDE buttons are for digital channels. If your TV is connected to an
ATSC antenna or Digital Cable, you can use these buttons.
• This remote control is capable of operating many external device brands. See page 70 - 75
for how to program the remote control.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Getting Started
These quick setup pages will provide you, in three easy steps, with the basic information you
need to begin using your new television right away. If you have questions, or for more detailed
information on any of these steps, please consult other sections of this manual.
Step 1 – The Remote Control
Before you can operate your remote control, you first need
to install the batteries (included).
Raise the latch on the remote's back cover to remove.
Insert two batteries, carefully noting the "+" and "–"
markings. Place the "–" end in the unit first. Snap the
cover back into place.
When you change the batteries, try to complete the
task within three minutes. If you take longer than
three minutes, the remote control codes (ex. VCR,
DVD) may have to be reset. See pages 70 - 75.
POWER
Basic Operation
Turn the television on and off by pressing the POWER button at the top right corner
of the remote. If this is the first time you are turning on the TV, the interactive
plug-in menu appears.
• At first, to watch your TV, select the TV mode by pressing the MODE button on
the remote control before you turn the TV power on. See page 60.
• See page 59 to 69 for details regarding the remote control buttons.
Note:
• If the lamp replacement message appears when you turn the television ON, see page 77.
Using Menu Buttons
To use the menu functions, press the MENU button. Next,
select a menu using the four arrow keys. The four arrow keys
are used only for menu selections.
OK
DVR
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Step 2 – Connecting Your Devices
To make these connections, you will use plugs like the ones illustrated below.
Component Cables
Coaxial Cables
Composite Cables
Audio Cables
Used to connect an
external antenna or
cable TV system to
your TV.
Used to connect audio/
video devices like
VCRs, DVD players,
stereo amplifiers, game
consoles, etc.
S-Video Cable
Used to make video
connections with S-Video
VCRs, Camcorders and
DVD players.
Notes:
• The following connection diagrams are examples.
• After you are finished connecting your devices, plug the power cord into the nearest power
outlet and turn on the TV.
• If you follow these diagrams and the television does not work properly, contact your local
cable operator.
• To connect a DVD player, see VCR Connection.
• If you have a satellite television system, refer to the satellite TV manual.
No VCR Connection
Cable or Antenna
Output
Coaxial Cable
75Ω
(VHF/UHF)
TV Side Panel
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
VCR Connection
Notes:
• Green, blue and red are the most common colors for DVD cables. Some models may vary
colors. Please consult the user’s manual for your DVD player for more information.
• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete
one set of connections (DVD or audio output) before starting the other to avoid accidentally
switching the cables.
• You may also connect the DVD player to Input 3.
Diagram #1
Cable or Antenna
Output
VCR
V
L
R
IN
IN
OUT
75Ω
(VHF/UHF)
OU
Coaxial Cable
OR
INPUT-3
INPUT-4
S-VIDEO
OVER
VIDEO
TV Side Panel
AUDIO IN
Y
Y
P
B
R
L
L
P
B
R
AUDI
AUDIO
P
R
R
P
Y
P
P
Green
Blue
B
R
Red
AUDIO OUT
OUT
R
L
DVD Player
Note:
• If this connection setup does not work for you, try the connection setup on page 16.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Diagram #2
Cable or Antenna
Output
VCR
IN
Two-Way Splitter
(NOT SUPPLIED)
OUT OUT
V
L
R
IN
IN
OUT
75Ω
(VHF/UHF)
OUT
Coaxial Cable
OR
INPT-3
INPUT-4
TV Side Panel
S-VIDEO
OVER
VIDEO
AUDIO IN
Y
Y
O
P
B
L
L
P
B
R
AUDIO
AUDIO
P
R
R
R
P
Y
P
P
Green
Blue
B
R
AUDIO OUT
Red
OUT
R
L
DVD Player
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connecting to a Camcorder
You may connect a camcorder, game console or other equipment to your television by using
the front input jacks (INPUT-5) located under the front panel door. To access, push on the
door to open it. You can also connect these using the television’s side input jacks, using the
same instructions.
INPUT-5
CHANNEL VOLUME
+
+
CAMCORDER
INPUT
MENU
VIDO L/MNO
P
–
–
AO
OPERATE
TV Front Panel
1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on
the front of the TV.
2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on
the front of the TV.
3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on
the front of the TV.
Note:
• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the
L/MONO on the front of the TV.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connecting to an External Amplifier
TV Side Panel
Speaker
Speaker
AUDIO
OUTPUT
Amplifier
L
R
1) Connect a white cable from the LEFT AUDIO OUTPUT on the side of the TV to the
LEFT AUDIO INPUT on the amplifier.
2) Connect a red cable from the RIGHT AUDIO OUTPUT on the side of the TV to the
RIGHT AUDIO INPUT on the amplifier.
Notes:
• Refer to your amplifier’s manual for more information.
• You can use AUDIO OUTPUT for your home theater system.
• You can not output audio using the AUDIO OUTPUT under the following conditions:
1) When you have digital sound from an HDMI device connected to the INPUT-1 or
INPUT-2 connection on the side of your TV. (See page 20).
2) When you have analog sound from a DVI device connected to the AUDIO IN "INPUT-1"
connection. (See page 19).
Connecting to an amplifier using your optical output
You can connect an amplifier that has an optical digital input terminal by using an optical digital
cable from the optical output. The signal that is output can be PCM or DOLBY DIGITAL.
Amplifier
TV Side Panel
OPTICAL OUT
Digital Audio
1) Connect the optical cable from the side of the TV to the back of the amplifier.
Notes:
• This terminal can only output digital audio.
• In order to use the optical output connection, select PCM or DOLBY DIGITAL on Digital
Sound in the Digital Setup Menu. See page 49.
• Refer to your owners manual on using your amplifier.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connecting to a Digital TV Receiver
By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in
their digital form.
After the connections have been made,
tighten the screw to secure the cables.
HDMI to DVI Cable
DTV Decoder
TV Side Panel
DIGITAL OUT
DIGITAL-IN
AUOUT
L
R
INPUT- 2
INPUT-1
AUDIO IN
1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to
the HDMI INPUT-1 on the side of your television.
2) Connect a red cable from the "R AUDIO OUT" on the back of your DTV Device, to the
HDMI AUDIO IN "R" input terminal.
3) Connect a white cable from the "L AUDIO OUT" on the back of your DTV Device, to the
HDMI AUDIO IN "L" input terminal.
• Personal computer compatibility cannot be guaranteed.
• Use a HDMI to DVI cable (commercially available) in order to digitally connect the television
with a DTV decoder.
Notes:
• If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance
may be slightly shifted. Access the “HDMI SIZE” in the initial setup menu to adjust it. (Refer
to page 47.)
• When you do the above connection, set "VIDEO-1 AUDIO" in the Initial Setup menu to
ANALOG. See "VIDEO-1 AUDIO", page 47.
• The Analog Audio input can only be used with the HDMI INPUT-1.
• When setting the “VIDEO-1 AUDIO – ANALOG / DIGITAL” menu setting on the TV, please
note that this setting only effects the HDMI INPUT-1 jack and that if you use a DVI to HDMI
adapter this connection must be made to the HDMI INPUT-1 along with analog audio cables.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connecting to an HDMI Compatible Device
By connecting an HDMI compatible device, high definition pictures can be displayed on your
TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI
compatible devices.
HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all
digital audio/video interface. HDMI provides and interface between any audio/video source,
such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a
digital television (DTV).
HDMI Cable
TV Side Panel
DIGITAL-IN
AUDIO OUT
L
R
HDMI Compatible Device
INPUT- 2
INPUT-1
AUDIO IN
L
R
Connect the HDMI Cable from the DIGITAL OUT on your DTV or HDMI device, to the HDMI
INPUT-1 or INPUT-2 on the side of your television.
Notes:
• When you do the above connection, set "VIDEO-1 AUDIO" in the Initial Setup menu to
DIGITAL. See "VIDEO-1 AUDIO", page 47.
• Some decoders may not respond depending on the equipment that you have connected
when it is connected to the HDMI.
• If the HDMI output device signal is changed (for example, 480i/60Hz is changed to
480p/60Hz), the screen may turn green and there may be some distortion for a short time
until the signal becomes stable.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connecting to an AV Receiver using your television's
V3 Smart Input
By connecting your AV Receiver to your television's V3 Smart Input, you can watch picture
sources from many different devices, without having to change or use the other input
connections on your TV. This allows you to free up the other input connections so you can
connect more devices to your television.
TV Side Panel
AV Receiver
INPUT-3
MONITOR
S-VIDEO
Y
OUT
OVER
P
B
Y
VIDEO
P
R
B
L
AUDIO
R
MONITOR OU
P
R
1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-3
on the side of your television.
2) Connect a Yellow Composite Cable from the AV Receiver's MONITOR OUT, into the VIDEO
INPUT-3 on the side of your television.
3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y
VIDEO INPUT-3 on the side of your television.
4) Connect a Blue Component Cable from the AV Receiver's PB MONITOR OUT, into the PB
VIDEO INPUT-3 on the side of your television.
5) Connect a Red Component Cable from the AV Receiver's PR MONITOR OUT, into the PR
VIDEO INPUT-3 on the side of your television.
Note:
• Please refer to your AV Receiver instruction manual for more information on connecting your
speakers and other devices like a DVD player.
• Use your AV Receiver's remote to switch to the different devices you have connected.
• Some AV Receivers may not respond when the V3 Smart Input function is turned on.
• If you have video connections for each input device connected to your AV Receiver, you
should not connect them using both S-Video and Composite connection at the same time
when you are using V3 Input as the V3 Smart Input. In this case we recommend using the
S-Video connection.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connecting to the computer
This TV can be used as a computer screen. Use a commercially available D-SUB cable to
connect the TV's PC INPUT terminal to the computer's analog RGB output terminal. If you
want to listen to the sound from the computer, use a commercially available RCA cable to
connect the INPUT-5 audio input terminal to the computer's audio output terminal.
Computer
INPUT-5
CHANNEL VOLUME
+
+
INPUT
MENU
VIDEO L/MONO
PC IN
R
–
–
AUDIO
OPERATE
TV Front Panel
Notes:
• Refer to your computer manual for a detailed explanation of the connections concerning your
computer.
• Make sure that the connectors are facing the correct way when connecting.
• After connecting, tighten the two screws to fix the connectors in place.
Looking at the images from a computer
After starting the computer, press the V5 button on the remote control. You can listen to the
sound when the sound from the computer is connected to the INPUT-5 AUDIO input terminal.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Table of signals for each type of computer
Resolution
Vertical
Frequency
(Hz)
Horizontal
Frequency
(kHz)
640 x 480
(VGA)
60.0
60.0
31.5
48.4
1024 x 768
(XGA)
• Only the above formats are supported.
• Even with the above formats at 60 Hz, some problems may be experienced depending on
the quality of the synchronous signal. (Depending on the quality, some pictures may not be
displayed correctly).
• Apple Macintosh* computers are not supported.
When a picture is not displayed
With some computers, some problems can be solved by changing the settings. Check the
computer's refresh rate and set it to 60Hz. Computers that cannot set the refresh rate to 60
Hz, can not be used with this TV. Refer to the computer's instruction manual.
*Apple Macintosh is a registered trademark of Apple Computer, Inc.
Note:
• If you are inputting a PC signal that is invalid, "Invalid Signal" will appear on the TV screen.
It appears when the input is PC and it is a single screen.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Step 3 – The Interactive Plug In Menu
When you turn your television on for the first time the interactive plug-in menu will appear. The
plug-in menu helps you to get your TV ready to use by letting you set your preferences for:
• The language in which you want the onscreen menus to appear.
• Setting the TV’s clock to the correct time so your timer functions will work properly. You can
choose “AUTO” or “MANUAL” for setting the clock.
• The auto tuner setup of which channels you wish to receive.
We recommend you complete the interactive plug-in items before you start using your
television.
Notes:
• The interactive plug-in menu setting does not appear if your TV has been turned on before.
In this case use the onscreen menus to perform these settings. See pages 40, 56, 30.
• If you press the Menu button while setting up the interactive plug-in menu, it will skip over it.
Language
After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically
switches to the LANGUAGE settings. You can choose to view your onscreen menus in three
languages: ENGLISH, FRANÇAIS (French) or ESPAÑOL (Spanish).
LANGUAGE/LANGUE/IDIOMA
è
To choose a language:
ENGLISH, FRANÇAIS or ESPAÑOL
†
To NEXT (To set clock)
ENGLISH
NEXT
SELECT OPERATE
MENU
EXIT
(Continued...)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Auto Clock Set
Before you use any of your TV’s timer functions, you must first set the clock. You may
precisely set your clock using the XDS time signal broadcast by most public analog
broadcasting stations. If you do not have this in your area, you will have to set the clock
manually. See manual clock set below. To set the clock using the XDS signal:
è
†
To choose AUTO
To TIME ZONE
SET CLOCK
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or Hawaii)
MODE
TIME
TIME ZONE
D.S.T.
AUTO
-- ----
:
ATLANTIC
ON
†
è
†
To move to D.S.T. (Daylight Savings Time)
To turn D.S.T. ON or OFF
To NEXT (To Auto Tuner Setup)
NEXT
MENU
SELECT OPERATE
EXIT
Notes:
• D.S.T. can be used when it is set to ON in the SET CLOCK menu.
• Only when the MODE is set to AUTO, the Daylight Saving Time feature automatically adjusts
your TV’s clock for Daylight Saving.
• The real time and D.S.T. may not be set correctly depending on the broadcasting signal and
receiving conditions. In this case, set your clock manually and turn D.S.T. to OFF.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
Manual Clock Set
To set your clock manually (without using the XDS signal), choose MANUAL. If you choose
AUTO, see auto clock set above.
è
†
To choose MANUAL
To TIME
SET CLOCK
è
†
è
†
To set the hour
To minute
To set the minute
To TIME ZONE
MODE
TIME
TIME ZONE
D.S.T.
MANUAL
-- ----
:
ATLANTIC
ON
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or Hawaii)
START CLOCK
SELECT OPERATE
†
To move to D.S.T. (Daylight Savings Time)
MENU
EXIT
è
†
To turn D.S.T. ON or OFF
To START CLOCK
Note:
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
(Continued...)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Auto Tuner Setup
In auto tuner setup, the TV automatically scans through all available channels, memorizing the
active ones and skipping over blank ones or channels with weak signals. This means when you
scan (using the CHANNEL +/– buttons) you will receive only clear, active channels.
AUTO TUNER SETUP
è
To choose CABLE or AIR (or SKIP when
you skip Analog Auto Tuner Setup)
TUNER MODE
AIR
†
To START
After Analog Auto Tuner Setup is finished, Digital Auto
Tuner Setup starts.
START
SELECT OPERATE
MENU
EXIT
NOW
Now Programming...
20
PROGRAMMING !
48
When the setup is finished, "THANK YOU ! SETUP IS NOW COMPLETE" is displayed. Your
quick setup is now complete. You can now begin watching your television, or you can continue
on in this guide for more information on programming your remote control, or using the
JVC onscreen menu system to customize your television viewing experience.
Notes:
• If you want to cancel the Auto Tuner Setup, press the MENU button.
• Noise muting will not work during Auto Tuner Setup.
• If you choose SKIP, it finished without doing the Auto Tuner Setup.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending
on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is
normal.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Using the Guide
Certain symbols are used throughout this guide to help you learn about the features of your
new television. The ones you will see most frequently are:
π† Up and Down arrows mean:
• Move vertically in a main menu screen
• Move through a submenu screen
• Move to the next letter, number, or other choice in a submenu
• Back up to correct an error
è Left and right arrows mean:
• Select a highlighted menu item
• Select an item in a submenu
• Select numbers in certain menu options
The “press button” icon means you should press the button named on your remote
control. (Button names appear in SMALL CAPITAL LETTERS.)
The “helping arrow” icon points to the highlighted or selected item in a menu.
To bring up the onscreen menu, press the MENU button on the remote control. The item that
appears in green is the one currently selected. If you use the Menu button on the TV’s front
panel instead of the remote, an additional menu screen showing VIDEO STATUS and ASPECT
will appear between INITIAL SETUP and PICTURE ADJUST. The “interactive plug-in menu” will
appear the first time the TV is plugged in.
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SET LOCK CODE
NEXT PAGE
(4/5)
EXIT
MENU
SELECT OPERATE
Note:
• Menus shown in this book are illustrations, not exact replications of the television’s onscreen
displays.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
The Onscreen Menu System
Your television comes with JVC’s onscreen menu system. The onscreen menus let you make
adjustments to your television’s operation simply and quickly. Examples of the onscreen
menus are shown on the next page. Detailed explanations on using each menu follow later in
this guide. For information about the interactive plug-in Menu, see pages 24 - 26.
The Onscreen Menu System
To open the onscreen menu system, press the MENU button on the remote control. You
navigate within the onscreen menus by using the four directional arrow buttons on the remote
control.
The selected feature and option on a menu screen are highlighted in a different color.
Selected Option
(Green)
Selected Option
(Blue)
ENG. FRAN. ESP.
LANGUAGE
CLOSED CAPTION
To move to a different feature use the π† arrows to move up or down the list. When you
press the up arrow at the top of the list or the down arrow at the bottom, the next menu screen
will appear. Use the arrows √ ® to select an option from the highlighted feature. Pressing
MENU on the remote control will close the onscreen menu system and return you to normal
television viewing.
Each menu and its features will be discussed in the following pages of this guide.
Notes:
• If you do not press any buttons for about a minute, the onscreen menu will automatically
shut off.
• Button names in this guide are shown in SMALL CAPITAL LETTERS.
• Menus may appear in different sizes onscreen depending on the aspect ratio selected.
• Some menu items may not appear in menu screens when certain aspect ratios or inputs
are selected.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Press the MENU button
To INITIAL SETUP 03
/
CLOCK TIMERS
INITIAL SETUP
INITIAL SETUP
PREVIOUS
PREVIOUS
PREVIOUS
HDMI SIZE
VIDEO-1 AUDIO
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
AUTO
DIGITAL
SET CLOCK
/
ON OFF TIMER
LAMP TIMER RESET
SET LOCK CODE
NEXT PAGE
(4/5)
EXIT
NEXT PAGE
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
MENU
MENU
SELECT OPERATE
EXIT
SELECT OPERATE
EXIT
INITIAL SETUP 04
CLOCK/TIMERS
INITIAL SETUP 01
INITIAL SETUP
INITIAL SETUP
SOUND ADJUST
PREVIOUS
TURN ON VOLUME
VOLUME LIMIT
PREVIOUS
PREVIOUS
NOISE MUTING
ON
OFF
ON
DIGITAL SETUP
10
40
FRONT PANEL LOCK
V3 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
OFF
(2/5)
RESET
NEXT PAGE
(5/5)
EXIT
NEXT PAGE
NEXT PAGE
(2/2)
EXIT
MENU
MENU
SELECT OPERATE
SELECT OPERATE
EXIT
MENU
SELECT OPERATE
INITIAL SETUP 02
INITIAL SETUP 05
SOUND ADJUST 02
PICTURE ADJUST
PREVIOUS
INITIAL SETUP
SOUND ADJUST
PREVIOUS
PREVIOUS
LANGUAGE
STANDARD
ENG. FRAN. ESP.
TINT
00
00
00
00
00
00
BASS
00
00
00
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
COLOR
PICTURE
BRIGHT
DETAIL
TREBLE
BALANCE
OFF
ON
IRIS
NEXT PAGE
(1/3)
EXIT
NEXT PAGE
(3/5)
NEXT PAGE
(1/2)
EXIT
MENU
SELECT OPERATE
MENU
SELECT OPERATE
EXIT
MENU
SELECT OPERATE
PICTURE ADJUST 01
INITIAL SETUP 03
SOUND ADJUST 01
PICTURE ADJUST
PICTURE ADJUST
PREVIOUS
STANDARD
PREVIOUS
DIGITAL VNR
MPEG NR
STANDARD
COLOR TEMPERATURE
COLOR MANAGEMENT
DYNAMIC GAMMA
HIGH
OFF
OFF
AUTO
ON
To INITIAL SETUP 04
ADVANCED SMART PICTURE
NATURAL CINEMA
ON
AUTO
RESET
NEXT PAGE
(2/3)
NEXT PAGE
(3/3)
MENU
MENU
EXIT
SELECT OPERATE
EXIT
SELECT OPERATE
PICTURE ADJUST 02
PICTURE ADJUST 03
Notes:
• The HDMI SIZE menu can only be displayed when a 480p picture signal is input to the HDMI
terminal and the picture is being displayed on the screen.
• ADVANCED SMART PICTURE menu cannot be displayed when DYNAMIC is selected for
Video Status.
• When the Menu button on the TV front panel is pressed, the FRONT PANEL CONTROL
menu between INITIAL SETUP 05 and PICTURE ADJUST 01 will appear.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Auto Tuner Setup
The auto tuner setup function is described on page 26 as the interactive plug-in menu. If you
need to run the auto tuner setup again, follow the steps below.
Press the MENU button
AUTO TUNER SETUP
π†
è
è
†
To AUTO TUNER SETUP
To operate
TUNER MODE
AIR
To choose CABLE or AIR
To START
è
To start the setup
START
OPERATE
MENU
SELECT
EXIT
The auto tuner is finished when the message PROGRAMMING OVER! appears onscreen.
Press the Menu button when finished
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Channel Summary
Channel summary allows you to customize the line-up of channels received by your TV.
Regarding analog channels, you can add or delete channels from the line-up or prevent any
unauthorized viewers from watching any or all 181 channels. Regarding digital channels, the
only channels that will appear are the ones that are broadcasting.
Press the MENU button
To CHANNEL SUMMARY
To operate
Analog Channels
CHANNEL SUMMARY
π†
CHNO. SCAN
01
ID
CHNO. SCAN
ID
HBO
è
06
The Channel summary screen will now be displayed with
the channels set to scan marked with an “√”. Regarding
analog channels, you can delete channels from the scan
by removing the “√”. If any channels were missed during
auto tuner setup and you wish to add them, you may by
placing an “√” next to the channel number.
02
03
04
05
MTV
07
08
09
10
L
A&E
E!
OK
MENU
SELECT
OPERATE
EXIT
Digital Channels
• Digital channels can not be added to the channel
summary if the auto tuner setup did not find them.
Channel Summary Digital
CH No.
D01
Scan
Station Name
FOX
π†√® To the SCAN column
Press the OK button to include or delete from
scan
D02
ABC
D02
CNN
D10-1
D10-2
D12345
NBC
BOX
Press the MENU button when finished
NHK
OK Operate
BACK Back
MENU Exit
Select
Note:
• The number of a digital channel may change,
depending on the time of some broadcastings. If
this channel existed and now has disappeared,
the lock channel or scanned channel mark by
the channel summary for that channel will be
cancelled.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
How to set the channel label. (This is only for analog broadcasting.)
Press the MENU button
ID
π†
è
è
To CHANNEL SUMMARY
To operate
To the ID column
CHANNEL 09
RESET
Press the OK button to enter
OK
PRESS TO FINISH
è
π†
To select the character you want
To move to the next space
MENU
SELECT OPERATE
EXIT
...continue to follow these directions for all four
spaces
Press the OK button to finish
Your characters are now set
Press the MENU button when finished
If you want to reset the characters you set:
Press the MENU button
π†
è
è
To CHANNEL SUMMARY
To operate
To the ID column
Press the OK button to enter
To select RESET
π†
Press the OK button to finish
Your characters are now reset
Notes:
• You can use characters for: Alphabet, numbers, marks and spaces.
• It is possible to set the maximum of 40 channel labels.
• If you try to set more than the 40 maximum, the message "MEMORY OVERFLOW" will
appear.
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
To CHANNEL SUMMARY
To operate
è
π†√® To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the MENU button when finished
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Channel Guard Message
When a viewer attempts to watch a guarded channel, the following message appears:
To watch a channel that you have locked, enter the
THIS CHANNEL IS LOCKED BY
Lock Code using the 10 key pad.
CHANNEL GUARD.
If the wrong code is entered, the message
PLEASE ENTER LOCK CODE BY
“INVALID LOCK CODE!” will flash on the screen.
10 KEY PAD TO UNLOCK IT.
The channel cannot be accessed until the correct code
NO. - - - -
is entered.
Notes:
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.
• See also “Set Lock Code”, page 39.
V-Chip
Your TV is equipped with V-Chip technology which enables you to block channels or content
that you feel to be inappropriate for children, based on US and Canada rating guidelines.
V-Chip has no effect on video signals from DVD discs or Camcorder connection.
Note: Some programs, and movies are broadcast without a ratings signal. Even if you set
up V-CHIP ratings limits, these programs will not be blocked. See page 34 for information on
how to block unrated programs.
Note (for Canadian viewers): The V-Chip function is based on specifications designed for
the United States and therefore may not work properly in Canada.
You can customize the V-Chip settings of your television to match your personal tastes. The
V-Chip menu below is the starting point for your V-Chip settings
You can use US V-Chip settings (for programming broadcast from the United States), Canadian
V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use
any or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting
each of the three V-Chip formats appear in the next six pages along with descriptions of the
rating categories.
To access the rating categories:
Press the MENU button
V-CHIP
V-CHIP
OFF
π†
è
To V-CHIP
To operate (Lock icon
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
will appear)
Press ZERO to access the V-Chip menu
VIEW
è
To turn V-Chip ON or OFF (V-Chip must be
turned ON for rating settings to operate)
π†
To move to SET US TV RATINGS,
SET MOVIE RATINGS, or
MENU
SELECT OPERATE
EXIT
SET CANADIAN RATINGS (see following
pages for descriptions of each item)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Unrated Programs
Unrated programming refers to any programming which does not contain a rating signal.
Programming on television stations which do not broadcast rating signals will be placed in the
“Unrated Programming” category.
Examples of Unrated programs:
• Emergency Bulletins
• News
• Public Service Announcements
• Sports
• Locally Originated Programming
• Political Programs
• Religious Programs
• Weather
• Some Commercials
Note:
• TV programs or movies that do not have rating signals will be blocked if the unrated category
is set to BLOCK.
Directions to Block Unrated Programs
You can block programs that are not rated.
Press the MENU button
V-CHIP
OFF
V-CHIP
π†
To V-CHIP
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
è
To operate (The lock icon
appears)
Press ZERO to access V-Chip setup options
VIEW
π†
To UNRATED
è
To VIEW or BLOCK
MENU
SELECT OPERATE
EXIT
Press MENU when done
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
US V-Chip Ratings
U.S. PARENTAL RATING SYSTEMS
Programs with the following ratings are appropriate for children.
❒ TV Y is Appropriate for All Children
Programs are created for very young viewers and should be suitable for all ages, including
children ages 2 - 6.
❒ TV Y7 is for Older Children
Most parents would find such programs suitable for children 7 and above. These programs
may contain some mild fantasy violence or comedic violence, which children should be able
to discern from reality.
Programs with the following ratings are designed for the entire audience.
❒ TV G stands for General Audience
Most parents would find these programs suitable for all age groups. They contain little or no
violence, no strong language, and little or no sexual dialog or situations.
❒ TV PG Parental Guidance Suggested
May contain some, but not much, strong language, limited violence, and some suggestive
sexual dialog or situations. It is recommended that parents watch these programs first, or
with their children.
❒ TV 14 Parents Strongly Cautioned
Programs contain some material that may be unsuitable for children under the age of 14
including possible intense violence, sexual situations, strong coarse language, or intensely
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.
❒ TV MA Mature Audiences Only
These programs are specifically for adults and may be unsuitable for anyone under 17
years of age. TV MA programs may have extensive V, S, L, or D.
Viewing Guidelines
In addition to the ratings categories explained above, information on specific kinds of content
are also supplied with the V-Chip rating. These types of content may also be blocked. The
content types are:
• V/FV is for VIOLENCE/FANTASY VIOLENCE
• S stands for SEXUAL CONTENT
• L stands for strong LANGUAGE
• D stands for suggestive DIALOG
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Setting US V-Chip Ratings
Press the MENU button
V-CHIP
V-CHIP
OFF
π†
è
To V-CHIP
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
To operate (lock icon
appears)
Press ZERO to access the V-Chip menu
VIEW
è
π†
è
To turn V-Chip ON or OFF
To move to SET US TV RATINGS
To operate
MENU
SELECT OPERATE
EXIT
Directions to set US V-Chip Ratings
Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and
press the π† or √® to move the cursor to the correct location. Press OK to turn the locking
feature on or off. An item is locked if the
icon appears instead of a “—”.
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that
column and add a lock icon. Once you’ve put a lock on the top row, everything in that column
is automatically locked.
SET US TV RATINGS
π†√® To the TV 14 Column
TV
TV
TV
PG
TV
G
TV
Y7
TV
Y
Press the OK button to lock
MA 14
Press the MENU button when finished
V/FV
S
L
Note:
D
• If you want to change the setup, move the cursor to
the top column and change the lock icon to “—” by
pressing OK again. You may then select individual
categories to block.
OK
MENU
EXIT
SELECT
OPERATE
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Movies Ratings
❒ NR – Not Rated
This is a film which has no rating. In many cases these films were imported from countries
which do not use the MPAA ratings system. Other NR films may be from amateur producers
who didn’t intend to have their film widely released.
NR (Not Rated) Programming may contain all types of programming including children’s
programming, foreign programs, or adult material.
❒ G – General Audience
In the opinion of the review board, these films contain nothing in the way of sexual content,
violence, or language that would be unsuitable for audiences of any age.
❒ PG – Parental Guidance
Parental Guidance means the movie may contain some contents such as mild violence,
some brief nudity, and strong language. The contents are not deemed intense.
❒ PG-13 – Parents Strongly Cautioned
Parents with children under 13 are cautioned that the content of movies with this rating may
include more explicit sexual, language, and violence content than movies rated PG.
❒ R – Restricted
These films contain material that is explicit in nature and is not recommended for
unsupervised children under the age of 17.
❒ NC-17 – No One Under 17
These movies contain content which most parents would feel is too adult for their children
to view. Content can consist of strong language, nudity, violence, and suggestive or explicit
subject matter.
❒ X – No One under 18
Inappropriate material for anyone under 18.
Directions to set Movie (MPAA) Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET MOVIE RATINGS
To enter movies menu
For example: To block viewing of programming rated
NC-17 shows, move the cursor to the NC-17 column and
add a lock icon. Once you've put a lock on the NC-17
column, X column is automatically locked.
SET MOVIE RATINGS
N
P
G13
X
C17
R
PG
G
π†√® To the NC-17 Column
Press the OK button to lock
NR
Press the MENU button to finish
OK
MENU
EXIT
SELECT
OPERATE
• If you want to change the setup, move the cursor to the
column and change the lock icon to “—” by pressing OK again.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Canadian V-Chip Ratings
❒ E – Exempt
Exempt programming includes: news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
❒ C – Programming Intended for Children
Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive
behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or
unrealistic in nature.
❒ C8+ – Programming Intended for Children 8 and Over
Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low
intensity and will show the consequences of the acts. There will be no offensive language,
nudity or sexual content.
❒ G – General Audience
Programming will contain little violence and will be sensitive to themes which could affect
younger children.
❒ PG – Parental Guidance
Programming intended for a general audience, but which may not be suitable for younger
children. Parents may consider some content not appropriate for children aged 8-13.
❒ 14+ – 14 Years and Older
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and
early teens. Programming may contain mature themes and scenes of intense violence.
❒ 18+ – Adult
Material intended for mature audiences only.
Directions to set Canadian V-Chip Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET CANADIAN RATINGS ENG (for English)
To enter ratings menu
For example: To block viewing of programming rated 14+ shows, move the cursor to the 14+
column and add a lock icon. Once you've put a lock
on the 14+ column, 18+ column is automatically
SET CANADIAN RATINGS ENG
locked.
P
C
8
G
C
18+
14+
G
è
To the 14+ Column
Press the OK button to lock
Press the MENU button to finish
MENU
OK
EXIT
SELECT
OPERATE
Notes:
• If you want to change the setup, move the cursor
to the column and change the lock icon to “—” by pressing OK again.
• For instructions on “SET CANADIAN RATINGS FRE (in French)”, please see page 38 in the
French user’s guide.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Set Lock Code
Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes
preset with a lock code of “0000”. You may change the code to any four-digit number you wish.
To change the lock code, follow the steps below.
Press the MENU button
SET LOCK CODE
π†
To SET LOCK CODE
To operate (lock icon
LOCK CODE
0000
è
appears)
Press ZERO to access the lock code
The first digit will be highlighted
OK
PRESS
TO FINISH
MENU
SELECT OPERATE
EXIT
è
π†
To select the number
To move to the next digit
Continue to follow these directions for all four numbers
Press the OK button to finish (your lock code is now set)
Press the Menu button when finished
When a viewer attempts to watch a blocked channel, this message appears:
THIS PROGRAMMING EXCEEDS
YOUR RATING LIMITS.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. - - - -
The channel will remain blocked until the correct lock code is entered (see above for
information on setting your lock code).
Notes:
• After a power interruption you must reset the lock code.
• Write your lock code number down and keep it hidden from potential viewers.
• If you forget the lock code, a new code may be set using the steps listed above.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Language
The language function is described on page 24 as the interactive plug-in menu. If you need to
choose the language again, follow the steps below.
Press the Menu button
INITIAL SETUP
PREVIOUS
π†
To LANGUAGE
LANGUAGE
ENG. FRAN. ESP.
è
To choose a language: ENG. (English),
FRAN. (French) or ESP. (Spanish)
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
Press the MENU button when finished
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
Closed Caption
Many broadcasts now include an onscreen display of dialog called closed captions. Some
broadcasts may also include displays of additional information in text form. Your television can
access and display this information using the closed caption feature. To activate the closed
caption feature, follow the steps below. There are three methods. When you are watching
analog channels, you can perform Analog Setting of closed caption. When you are watching
digital channels, you can perform Digital Auto Setting or Digital Manual Setting.
Analog Setting
Press the MENU button
CLOSED CAPTION
π†
è
π†
è
π†
è
To CLOSED CAPTION
To enter
To MODE
To select CAPTION or TEXT in MODE
To CAPTION or TEXT
To select a caption (CC1 to CC4) or text
channel (T1 to T4)
MODE
TEXT
CC1
T1
CAPTION
TEXT
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
Press the OK button to save
Press the MENU button when finished
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Digital Auto Setting
Press the MENU button
Digital Closed Caption
Preview
π†
To CLOSED CAPTION
To enter
To Type
Closed Caption Sample
è
π†
è
Type
Auto
1
Service
Appearance
To select Auto, Advanced or Basic
Auto: Shows closed caption a priority for
digital channels over analog channels. It is
set automatically.
Cancel
Set
Operate BACK Back
MENU Exit
Select
Advanced: Shows only the digital closed
caption.
Basic: Shows only the analog closed
caption.
Digital Closed Caption > Appearance
Preview
Closed Caption Sample
Appearance Mode
Font
Auto
π†
è
π†
è
è
π†
To Service
To select 1, 2, 3, 4, 5 or 6
To Appearance
To enter
To select Auto
To Set
Colors
Opacities
Cancel
Set
BACK Back
MENU Exit
Select
Operate
Press the OK button to save
The font/type and color are set automatically.
Press the MENU button when finished
Note:
• If you want to cancel the settings, select cancel.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Digital Manual Setting
Press the MENU button
Digital Closed Caption
Preview
>
Appearance
π†
To CLOSED CAPTION
Closed Caption Sample
è
π†
è
π†
è
π†
è
è
π†
è
π†
è
To enter
To Type
Appearance Mode
Manual
Font
Colors
Opacities
To select Auto, Advanced or Basic
To Service
To select 1, 2, 3, 4, 5 or 6
To Appearance
To enter
To select Manual
To Font
To enter
To select Font Size or Font Style
To select the setting you like
Cancel
Set
BACK
MENU
Select
Operate
Back
Exit
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Font Size
Standard
Auto
Appearance Mo
Font
Font Style
Colors
Font Size: Auto, Standard, Large or Small
Cancel
Set
Opacities
Cancel
Font Style: Auto, Serif Mono, Serif, SanSerif Mono,
SanSerif, Casual, Cursive or Small Capital
π†
Set
BACK
MENU
Select
Operate
Back
Exit
To Set
Press the OK button to save
π†
è
π†
è
To Colors
To enter
To select Text, Edge or Background
To select the setting you like
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Text
Appearance Mo
White
White
Black
Edge
Auto, White, Black, Red, Green, Blue,
Yellow, Magenta or Cyan
Font
Background
Cancel
Colors
Opacities
Set
π†
To Set
Cancel
Set
Press the OK button to save
BACK
MENU
Select
Operate
Back
Exit
π†
è
π†
è
To Opacities
To enter
To select Text/Edge or Background
To select Auto, Transparent, Translucent, Solid
or Flashing
All fonts used for digital closed
caption and digital menus are
licensed from Monotype Imaging
Inc.
π†
π†
To Set
Press the OK button to save
To Set
Press the OK button to save
Press the MENU button when finished
Notes:
• Closed caption subtitles are usually found on closed caption channel CC1. Some programs may
include additional text information which is usually found on text channel T1. The other channels
are available for future use.
• Closed captioning may not work correctly if the signal being received is weak or if you are playing
a video tape.
• Most broadcasts containing closed captioning will display a notice at the start of the program.
• To select the mode, press the C.C. button. See page 66.
• When ZOOM aspects like PANORAMA or CINEMA are selected, Digital Closed Captions may be
cut off or distorted.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Auto Shut Off
This function automatically shuts off your TV when there is no signal from the channel the
TV is on.
INITIAL SETUP
Press the MENU button
PREVIOUS
LANGUAGE
ENG. FRAN. ESP.
π†
è
To AUTO SHUT OFF
To turn ON or OFF
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
Press the MENU button when finished
• If the channel that you have on does not receive a
signal for more than one minute, the blinking text
“NOT RECEIVING A SIGNAL AUTO SHUT OFF
IN 9 MIN.” appears on the screen, and starts the
countdown. If no signal is being received within 10
minutes, the TV shuts itself off.
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
XDS ID
XDS ID Display provides a channel’s call letters, the network’s name, and even a program
name. The XDS ID information is provided by the broadcaster.
INITIAL SETUP
Press the MENU button
PREVIOUS
LANGUAGE
ENG. FRAN. ESP.
π†
è
To XDS ID
To turn ON or OFF
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
Press the MENU button when finished
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
Noise Muting
This feature inserts a blank gray screen over channels which are not broadcasting or are too
weak to be received clearly.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To NOISE MUTING
To turn noise muting ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V3 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
Press the MENU button when finished
OFF
NEXT PAGE
(2/5)
MENU
Notes:
SELECT OPERATE
EXIT
• Noise muting will not work during auto tuner setup or
when you operate channel summary.
• Noise muting will not work when the digital TV is displayed.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Front Panel Lock
This allows you to lock the keys on the front of the TV, so that a child may not accidentally
change your viewing preferences.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To FRONT PANEL LOCK
To turn ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V3 SMART INPUT
Press the MENU button when finished
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
You can turn off this feature in the following ways:
OFF
NEXT PAGE
(2/5)
• Unplug the power cord, and plug it back in. Do this if
your batteries die, or you lose your remote control.
MENU
SELECT OPERATE
EXIT
• Use the remote control.
• Press the MENU button on the front of the TV for more than 3 seconds. In this case, the OSD
for FRONT PANEL LOCK will appear.
Note:
• To turn ON/OFF the TV, press the power button for more than 3 seconds. This feature will
remain ON.
V3 Smart Input
This feature is used if you have connected an AV Receiver to your television. By turning this
feature on, your television can automatically detect the signal source from your components
that are connected to your AV Receiver.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To V3 SMART INPUT
To turn ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V3 SMART INPUT
Press the MENU button when finished
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
Notes:
OFF
NEXT PAGE
(2/5)
• If you do not have an AV Receiver connected to your
television, turn this feature OFF.
MENU
SELECT OPERATE
EXIT
• Some AV Receivers may not work with this function.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Video Input Label
This function is used to label video input connections for the onscreen displays.
Press the MENU button
To VIDEO INPUT LABEL
To enter
INITIAL SETUP
PREVIOUS
π†
è
π†
è
NOISE MUTING
FRONT PANEL LOCK
V3 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
ON
OFF
ON
To select the desired video input
OFF
To select the desired preset input label (see
chart below)
NEXT PAGE
(2/5)
MENU
SELECT OPERATE
EXIT
Press the OK button to save
VIDEO INPUT LABEL
Press the MENU button when finished
VCR
DVD
SAT
GAME
STB
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
VIDEO-5
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
Preset
Labels
Select when...
VCR
DVD
PVR
You have a VCR connected to the video input
You have a DVD connected to the video input
You have a Personal Video recorder connected to the video input
You have a Digital VCR connected to the video input
You have a Set-top Box connected to the video input
You have a Satellite Receiver connected to the video input
You have an Amplifier connected to the video input
You have a Video Game connected to the video input
You have a Video Camera connected to the video input
You have a Video Disc player connected to the video input
DVHS
STB
SAT
AMP
GAME
CAM
DISC
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Position Adjustment
Position adjustment allows you to adjust the position of the picture on the screen vertically
when the aspect is set to panorama or cinema.
Press the MENU button
π†
è
To POSITION ADJUSTMENT
To enter
π†√® To adjust the position
Press the MENU button to finish
Notes:
OK
MENU
RESET
EXIT
OPERATE
• To reset the adjustment to the center, press the
OK button.
• When the arrow disappears, while you are adjusting the position, the position is at its
maximum limit.
• If you select REGULAR, SLIM and FULL size with aspect or Multi Screen, position
adjustment option is not seen.
• When you change the screen size, perform the position adjustment again.
• Position adjustment allows you to adjust the screen position vertically and horizontally when
the aspect is set Panorama Zoom or Cinema Zoom for 1080i and 720p signals, or when PC
mode is set.
• It is also possible to use Position Adjustment when you are in PC Mode
• When you are receiving a 1080p signal, Position Adjustment can not be selected.
Power Indicator
Power indicator allows you to adjust the brightness of the power indicator
Press the MENU button
INITIAL SETUP
PREVIOUS
NOISE MUTING
ON
OFF
ON
π† To POWER INDICATOR
FRONT PANEL LOCK
V3 SMART INPUT
è
To adjust POWER INDICATOR LOW, HIGH
or OFF
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
Notes :
• When OFF is selected :
OFF
NEXT PAGE
(2/5)
The LED disappears if you have a TV signal.
The LED is lit as “LOW” when there is no TV signal.
MENU
SELECT OPERATE
EXIT
• When the On Timer turns ON, the LED is lit as
"LOW" when you turn the power off.
• If you set a timer on the TV, the power indicator will light even if the TV is on stand by.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
HDMI Size
The HDMI SIZE option can only be displayed in the INITIAL SETUP menu when an HDMI
480p picture signal is being input to the HDMI terminal. This option adjusts the position when
an HDMI or DVI 480p picture signal is being displayed on the screen. There are two types of
HDMI 480p picture signals: 640x480 and 720x480. If the displayed picture is slightly shifted,
the position can be adjusted by selecting AUTO, SIZE1 or SIZE2.
INITIAL SETUP
Press the MENU button
PREVIOUS
HDMI SIZE
π†
è
π†
To HDMI SIZE
AUTO
DIGITAL
VIDEO-1 AUDIO
To enter
To select AUTO, SIZE1 or SIZE2
Press the MENU button to finish
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
Notes:
• The HDMI SIZE menu can only be displayed when a HDMI or DVI 480p picture signal is input
to the HDMI terminal and the picture is being displayed on the screen.
• You can select AUTO only when the signal is 480p for HDMI. When you select AUTO, the
television will select "SIZE1" or "SIZE2" automatically.
Video-1 Audio
This feature is used if you have a DVI or HDMI compatible component connected to your TV.
Press the MENU button
INITIAL SETUP
PREVIOUS
HDMI SIZE
VIDEO-1 AUDIO
π†
è
To VIDEO-1 AUDIO
To select ANALOG, DIGITAL or AUTO
AUTO
DIGITAL
Press the Menu button when finished
Notes:
NEXT PAGE
(1/5)
• If your DVI or HDMI component is capable of digital
audio and video, choose DIGITAL. If your DVI or HDMI
MENU
SELECT OPERATE
EXIT
component is capable of analog audio and digital video, choose ANALOG.
• Refer to your DVI or HDMI component’s instruction manual for more information.
• When you select AUTO, the television will select "ANALOG" or "DIGITAL" automatically,
depending on the audio input from the HDMI.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Digital Setup
Use this function when you are receiving a digital broadcast.
Press the MENU button
Digital Setup
Antenna Level
π†
To DIGITAL SETUP
To enter
Digital Sound
PCM
è
Software Version
The onscreen will appear
Notes:
Software Update
• Software Update will only appear when the USB
memory is inserted into the USB connector.
Operate BACK Back
MENU Exit
Select
• If you are watching an analog channel, you can still
access the digital setup menu at anytime, while you are doing this, the background screen
will turn blank. In this case, the tuner will switch to digital, since you are accessing the digital
setup menu.
Antenna Level
Confirms the present antenna level.
Antenna Level
Press the MENU button
75
π†
To DIGITAL SETUP
To enter
BACK
MENU
è
Back
Exit
π†
To Antenna Level
To enter
è
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Digital Sound
You can select the optical digital sound output, either PCM or DOLBY DIGITAL when your TV
is connected to an amplifier that has DOLBY DIGITAL decoder. If you select DOLBY DIGITAL,
you can enjoy listening in 5.1ch sound when watching digital broadcasts.
Press the MENU button
π†
è
To DIGITAL SETUP
To enter
π†
To Digital Sound
è
To select PCM or DOLBY DIGITAL
Press the MENU button when finished
Notes:
• If your amplifier does not have DOLBY DIGITAL decoder, select PCM. If you don't select
PCM, it cannot output the sound from the speakers.
• For connecting an amplifier using the optical output, see page 18.
Manufactured under license from Dolby Laboratories. "Dolby", and
the double-D symbol are trademarks of Dolby Laboratories.
Software Version
You can confirm the Software Version.
Press the MENU button
π†
è
To DIGITAL SETUP
To enter
π†
è
è
To Software Version
To enter
Select close when you are finished confirming your software version
Press the MENU button when finished
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Software Update
At first, connect the USB memory into the USB connector. This function will appear only when
the USB memory is inserted into the USB connector.
Press the MENU button
π†
è
π†
è
π†
To DIGITAL SETUP
To enter
To Software Update
To enter
Checks if it needs an update or not
Press the MENU button when finished
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Picture Settings
These settings allow you to change and adjust the way the picture appears on your television.
TINT
Tint allows you to adjust the levels of red and green in your TV picture.
COLOR
The color function lets you make all the colors in the TV picture appear either more vivid or
subtle.
PICTURE
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker
or brighter picture overall.
BRIGHT
You can adjust the overall brightness of the TV picture with the Bright control.
DETAIL
The Detail feature adjusts the level of fine detail displayed in the picture.
IRIS
The IRIS adjusts the level of brightness on the TV screen.
Adjust the Picture Settings
Press the MENU button
PICTURE ADJUST
π†
To TINT, COLOR, PICTURE, BRIGHT,
DETAIL or IRIS
To enter
PREVIOUS
TINT
STANDARD
00
00
00
00
00
00
COLOR
PICTURE
BRIGHT
DETAIL
è
+02
TINT
IRIS
NEXT PAGE
(1/3)
EXIT
è
π†
π†
To adjust the setting
To back to the picture main menu
To move to the next setting
MENU
SELECT OPERATE
Press the MENU button when finished
Note:
• There are four video status settings: Dynamic, Standard, Theater and Game. Each video
status setting has a separate memory for HD (1080i/1080p/720p) and SD (480p/480i) video
signal. Each video status can be chosen along with your favorite picture settings (Tint,
Color, Picture, Bright, Detail, etc.) See page 66 for details.
Color Temperature
You can decide how strong or dull the colors appear on the TV screen.
Press the MENU button
COLOR TEMPERATURE
LOW
π†
è
π†
To COLOR TEMPERATURE
To enter
To set LOW or HIGH
HIGH
Press the MENU button when finished
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Color Management
This TV supports the COLOR MANAGEMENT function to ensure dull colors are compensated
to produce natural hues.
Press the MENU button
COLOR MANAGEMENT
ON
π†
è
π†
To COLOR MANAGEMENT
To enter
To select the mode “ON" or "OFF"
OFF
Press the MENU button when finished
Dynamic Gamma
JVC's Dynamic Gamma Circuitry (DGC) makes it easier to see dark areas when a picture
has many dark areas, and makes it easier to see the bright areas when a picture has many
bright areas. DGC is turned on, DGC analyzes and adjusts the total level of picture brightness
balance, especially in dark areas where the level of grayscale is often lost, turning completely
to black DGC automatically enhances the detail in these dark areas providing a more dynamic
image with finer detail, so the optimum picture settings are automatically set for each picture.
Normally use with DGC on.
Press the MENU button
DYNAMIC GAMMA
ON
π†
è
π†
To DYNAMIC GAMMA
To enter
To turn ON or OFF
OFF
Press the MENU button when finished
Advanced Smart Picture
Advanced Smart Picture detects the APL (Average Picture Level) and adjusts the level of
brightness on the TV screen suitable for what you are watching.
Press the MENU button
ADVANCED SMART PICTURE
ON
π†
è
π†
To ADVANCED SMART PICTURE
To enter
To select the mode "ON" or "OFF"
Press the MENU button when finished
OFF
Note:
• When you have "DYNAMIC" selected in the "VIDEO STATUS", Advanced Smart Picture is
not selected.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Natural Cinema
Natural cinema corrects the problem of blurred edges which may occur when viewing a program
originally shot on film (such as motion pictures) or animation. If you notice blurring at the edges
of these programs, choose NATURAL CINEMA and set it to AUTO. Natural Cinema helps correct
conversion errors that occur when film, which is shot at 24 frames-per-second, is broadcast at the
television rate of 30 frames-per-second.
NATURAL CINEMA
Press the MENU button
AUTO
π†
è
π†
To NATURAL CINEMA
To enter
To select the mode “AUTO", "ON" or "OFF”
ON
OFF
Press the MENU button when finished
Notes:
• When you are receiving a 1080p signal, Natural Cinema can not be selected.
• The natural cinema mode is automatically set to “AUTO” in the following cases:
- Turning on or off
- Changing the channel or input mode
• If you are in PC mode, Natural Cinema can not be used.
Digital VNR
This function can be selected to change the effect of Digital VNR (Video Noise Reduction).
Press the MENU button
DIGITAL VNR
AUTO
MIN
π†
è
π†
To DIGITAL VNR
To enter
To select the effect you like.
MAX
OFF
AUTO: adjusts the effect of VNR automatically.
MIN: adjusts the effect of VNR to minimum.
MAX: adjusts the effect of VNR to Maximum.
OFF: turns the effect of VNR off.
Press the MENU button when finished
Notes:
• If it is in PC, Digital VNR will not be displayed.
• When you are receiving a 1080p signal, Digital VNR can not be selected.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
MPEG NR
This function effects the block noise removal and mosquito NR (Noise Reduction)
simultaneously.
Press the MENU button
MPEG NR
ON
π†
è
π†
To MPEG NR
To enter
OFF
To select ON or OFF
Press the MENU button when finished
Notes:
• When you are receiving digital channels, block noise removal will have no effect.
• When you are receiving a 1080p signal, MPEG NR can not be selected.
Reset
Reset resets all picture adjustments (Tint, Color, Picture, Bright, Detail, Iris, Color Temperature,
Color Management, Dynamic Gamma, Advanced Smart Picture, Digital VNR and MPEG NR) at
once to the default settings.
PICTURE ADJUST
Press the MENU button
PREVIOUS
DIGITAL VNR
MPEG NR
STANDARD
π†
è
To RESET
To enter
AUTO
ON
The onscreen menu disappears for a moment,
and then the settings are reset to the default
setting for all the picture adjustments.
RESET
NEXT PAGE
(3/3)
MENU
Press the MENU button when finished
SELECT OPERATE
EXIT
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Sound Settings
These settings allow you to change and adjust the sound on your television.
BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with
the bass adjustment.
TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.
BALANCE – Adjust the level of sound between the TV’s left and right speakers with the
balance setting.
Adjust the Sound Settings
Press the MENU button
SOUND ADJUST
PREVIOUS
π†
√ ®
π†
To BASS, TREBLE or BALANCE
To adjust the setting
To move to the next setting
BASS
00
00
00
TREBLE
BALANCE
Press the MENU button when finished
NEXT PAGE
(1/2)
EXIT
Note:
MENU
SELECT OPERATE
• You can reset the sound adjustments (BASS, TREBLE
and BALANCE) you set at once as the default setting
when you select reset.
• You can adjust BALANCE only when A.H.S.+ is off. See page 65.
Turn On Volume
Turn On Volume allows you to set the volume level when you turn the TV on.
Press the MENU button
π†
è
To TURN ON VOLUME
To set
Current
00
01
02
03
48
49
50
Press the MENU button to finish
Volume Limit
Volume Limit allows you to set the maximum volume level.
Press the MENU button
π†
è
To VOLUME LIMIT
To set the maximum volume level
00
01
02
03
48
49
50
Press the MENU button to finish
Reset
Reset resets all Sound Adjustments (Bass, Treble, Balance, Turn On Volume and Volume Limit)
at once to the default settings. See page 54 on how to use reset.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Set Clock
The set clock function is described on page 25 as the interactive plug-in menu. You can choose
to set the clock automatically or manually. If you need to set the clock again, follow the steps
below.
Press the MENU button
π†
è
To SET CLOCK
To enter
When you set the clock automatically, choose AUTO by pressing the
√
or
®
arrows.
π†
è
To TIME ZONE
To select your time zone
ATLANTIC
SET CLOCK
EASTERN
CENTRAL
MOUNTAIN
HAWAII
ALASKA
PACIFIC
MODE
TIME
TIME ZONE
D.S.T.
AUTO
π†
è
To D.S.T. (daylight savings time)
To turn D.S.T. ON or OFF
-- ----
:
ATLANTIC
ON
Press OK to finish
OK
PRESS TO FINISH
Press the MENU button when finished
MENU
SELECT OPERATE
EXIT
When you set the clock manually, choose MANUAL by
pressing the or arrows.
√
®
π†
è
π†
è
π†
è
To move to the hours
To set the hours
To move to minutes
To set the minutes
To TIME ZONE
To select your time zone:
SET CLOCK
(Atlantic, Eastern, Central, Mountain, Pacific,
Alaska or Hawaii)
MODE
TIME
TIME ZONE
D.S.T.
MANUAL
π†
To D.S.T. (daylight savings time)
-- ----
:
è
To turn D.S.T. ON or OFF
Press OK to start clock
ATLANTIC
ON
THANK YOU !!
OK
PRESS TO START CLOCK
MENU
SELECT OPERATE
EXIT
Press the MENU button when finished
Notes:
• D.S.T. can be used when it is set to ON in the SET CLOCK menu.
• Only when the MODE is set to AUTO, the Daylight Saving Time feature automatically adjusts
your TV’s clock for Daylight Saving.
• The real time and D.S.T. may not be set correctly depending on the broadcasting signal and
receiving conditions. In this case, set your clock manually and turn D.S.T. to OFF.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
On/Off Timer
The on/off timer lets you program your television to turn itself on or off. You can use it as an
alarm to wake up, to help you remember important programs, or as a decoy when you’re not
home.
Press the MENU button
ON/OFF TIMER
π†
è
è
To ON/OFF TIMER
7:00 PM
10:00 PM
03
ON TIME
OFF TIME
CHANNEL
ON VOLUME
MODE
To enter (begins with ON TIME)
CURRENT
EVERYDAY
NO
To set the hour (AM/PM) you want the TV to
turn on
ON/OFF TIMER
π†
è
π†
To move to minutes
To set the minutes
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
To accept ON TIME and move to OFF TIME (the time the TV will turn off). Set the
OFF TIME the same way as ON TIME
π†
è
π†
è
π†
è
To accept OFF TIME and move to CHANNEL
To select channel
To ON VOLUME
To set the volume level
To move to MODE
Choose ONCE or EVERYDAY
π†
To ON/OFF TIMER
è
Choose YES to accept the timer setting, choose NO if you don’t wish to accept
Press the OK button to finish
Press the MENU button to exit the menu
Notes:
• The on/off timer cannot be set to locked or guarded channels.
• In order for the on/off timer to work, the clock must be set.
• After a power interruption, the timer settings must be reset.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Lamp Timer Reset
The lamp replacement message will appear when you need to change the lamp. After you
replace the lamp, you need to reset the timer which is built into your television.
Press the MENU button
/
CLOCK TIMERS
PREVIOUS
SET CLOCK
π†
To LAMP TIMER RESET
To Enter
/
ON OFF TIMER
è
LAMP TIMER RESET
The following message will appear.
NEXT PAGE
MENU
SELECT OPERATE
EXIT
PRESS OK TO RESET THE LAMP
TIMER.
Press the OK button while the above message appears on the television screen.
THE LAMP TIMER IS RESET
SUCCESSFULLY.
The lamp timer has now been reset.
Notes:
• You can use the Lamp Timer Reset only after replacing the lamp.
• See Page 77 for instructions on lamp replacement.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Power
Turns the TV on or off.
Press the POWER button
Note:
• After turning the power on, you can not turn the power off for about one minute.
Number Buttons - 10Key Pad
Use the number buttons on the remote control to move directly to a specific channel. For
example, to move to channel 12:
1 (One)
2 (Two)
Tune
Lets you decide the input channel and select it. After you press the number buttons on the
remote, press the TUNE button. For example, to move to channel 12:
1 (One)
2 (Two)
Press the TUNE button
Channel +/–
Use these buttons to move up or down all the available channels your TV is able to receive.
To move rapidly through the channels using JVC’s Hyperscan feature, press and hold CH+ or
CH–. The channels will zip by at a rate of five channels per second.
Volume +/–
Use these buttons to raise or lower the TV’s volume level. The maximum is the level you set in
Volume Limit. See page 55.
Muting
The MUTING button instantly turns the volume down completely when you press it. Press
MUTING and the volume level will instantly go to zero. To restore the volume to its previous
level, press MUTING again.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
D/A (Digital/Analog)
The D/A button changes the analog and digital channel. Digital channels have a "D" in front of
the channel number.
Press the D/A button
By every press of the D/A button, you can switch between analog and digital
channels.
To watch digital channels
For example, to move to channel D23:
Press 2 (Two)
Press 3 (Three)
Press the TUNE button
Mode
Your remote control can be used to operate some basic functions of your external devices. To
use your device, select the proper mode.
Press the MODE button
By every press of the Mode button, you can select the mode.
TV
STB
VCR
DVD
AUDIO
• The indicator on the remote control lights for 3 seconds each time the remote control is
operated.
MODE
Device
TV
TV
STB
VCR
VCR/DVR
DVD
DVD Player
(DVD Recorder)
AUDIO
Amplifier/Home
Theater in Box
STB/DVR
(Cable Satellite)
• The mode light, except for TV lights to indicate which mode is selected.
Input
Selects the signal input source for the television: VIDEO-1, 2, 3, 4 or 5 for video devices like
VCRs, DVD players or camcorders.
Press the V1, V2, V3, V4 or V5 button
Notes:
• When you return to TV mode, press the RETURN +/TV button or direct 10 key pad or CHANNEL
+/– button.
• You can also access by pressing the INPUT button on the front of the TV instead of the
remote control.
• If you have a PC connected to the TV, select VIDEO-5 (V5).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Return +/TV
The RETURN+/TV button has three functions:
Return - Returns to the channel viewed just before the channel currently onscreen.
Return+ - Lets you program a specific channel to return to while scanning through the
channels using the CH+ and CH– buttons.
TV - Returns to the TV mode.
Press the RETURN+/TV and hold for three seconds
RETURN CHANNEL
PROGRAMMED!
The channel currently active has been programmed as your return+ channel. Now scan
through the channels using the CHANNEL+/– buttons.
Press the RETURN+/TV
You will return to your programmed channel.
• To cancel your return+ channel, press and hold the RETURN+ button for three seconds. The
message “RETURN CHANNEL CANCELLED!” will appear.
• Return+ works only with the Channel+/– buttons. Pressing any number key will cancel
return+.
Light
All remote control buttons are illuminated, except for the Light button. Press the LIGHT button
to turn the illumination on for 5 seconds.
Menu
The MENU button allows you to access JVC’s onscreen menu system. Press MENU to activate
the onscreen menu system.
• See individual topics like “Sound Adjust” for specific information on using menus.
OK
This button confirms your selection when you are in one of the onscreen menus.
Back
This button allows you to go back in the menu to change a selection or correct a mistake.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Favorite
The Favorite button allows you to select your favorite channels easily. First, you must register
the channels that you like. See how to register below.
Press the FAVORITE button
FAVORITE
The favorite channel list will appear.
PREVIOUS
π†
To select the channel you want to watch
101
102
D103
<
CBS
FOX
PBS2
>
Press the OK button
It will change to the channel you have selected.
D107
8
HBO
ABC
Register the favorite channel
Press the channel number you want to register
The channel program will change.
NEXT
Press the FAVORITE button for three seconds
The channel will be registered in the favorite channel list.
Notes:
• Both analog and digital channels can be registered. The digital channels have a "D" in front
of the channel number.
• The maximum number of channels you can register is 24.
• If you have registered the maximum number of channels, and try to register more channels,
the oldest channel you registered will be deleted.
• Sub channels can not be registered.
• The newest channel you registered will appear at the top of the list.
Delete the favorite channel
Press the FAVORITE button
The favorite channel list will appear.
π†
è
To select the channel you want to delete
To enter
Press the FAVORITE button
The channel was deleted.
Note:
• Before pressing the FAVORITE button when you are finished, press the √® button again, and
you can return to the deleted channel.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Aspect
This feature will help you adjust the picture you are watching to give you the best possible
picture quality.
Aspect Ratios
PANORAMA - With this ratio a normal
4:3 aspect picture is stretched to fit the
dimensions of the 16:9 aspect screen.
REGULAR - The regular ratio is used
when you want to watch a 4:3 broadcast
or recorded program without modifying the
original picture to fit the dimensions of your
16:9 screen. The 4:3 picture will fill the
screen from top to bottom, while black bars
will appear to fill up the remaining space
along the picture’s sides. The 4:3 picture
will be centered within the boundaries of the
16:9 screen.
CINEMA - This ratio “zooms in” on the
center part of a 4:3 aspect picture, blowing
it up to fill the 16:9 screen.
SLIM - This aspect mode shrinks the
screen of 16:9 to 4:3. There are some
programming that is already stretched by
mistake at broadcasting companies, so
this mode corrects it. Black side bars will
appear.
FULL - This is the ratio to use when
watching 16:9 High-Definition broadcasts.
PANORAMA ZOOM - This ratio stretches
the High-Definition 16:9 aspect image to
eliminate the black side bars.
Aspect Ratios in PC Mode
REGULAR - This is the original aspect
mode.
CINEMA ZOOM - This ratio stretches
the High-Definition 16:9 aspect image to
eliminate the black surrounding bars.
FULL - This aspect mode stretches the
image to fit the dimensions of the 16:9
aspect screen.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Aspect Ratios (Continued)
Press the ASPECT button
• By pressing the ASPECT button, you can change the size.
When you change the aspect ratios, it is different from their broadcast or recorded program.
PC
ATSC (480i, 480p)
SD (480i, 480p)
HD (1080i, 720p)
NTSC, 480i, 480p
ATSC (1080i, 720p)
ASPECT
PANORAMA ZOOM
CINEMA ZOOM
FULL
ASPECT
PANORAMA ZOOM
CINEMA ZOOM
FULL
ASPECT
ASPECT
PANORAMA
CINEMA
FULL
REGULAR
FULL
SLIM
REGULAR
Notes:
• You can also choose the size by pressing the π† buttons.
• When you change the aspect ratio or signal, reset the picture position to center.
• You can also access the FRONT PANEL CONTROL screen by using the MENU button
on the front of the TV instead of the remote control. It appears between INITIAL SETUP
and PICTURE ADJUST screen, and it has VIDEO STATUS and ASPECT menus. Choose
ASPECT by pressing Menu
+/- buttons.
†
on the front panel and choose a mode by using the CHANNEL
• "SLIM" can only be displayed when the signal is ATSC (480i or 480p).
• If the television receives a 16:9 signal from your HDMI device, the aspect mode will turn to
FULL automatically. If the television receives a 4:3 signal from your HDMI device when you
are in FULL aspect mode, it will return to REGULAR aspect mode. If you change the aspect
mode after the television changed it to FULL automatically, the television will change to the
aspect mode you choose.
• When you are receiving a 1080p signal, you can not change the aspect ratios.
Guide
You can view the program from the GUIDE.
Notes:
• The GUIDE function will only work when you are receiving digital programming only.
• The GUIDE will not show the correct time and date if you have not performed the set clock
function on your television. See page 56.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Sound
By pressing the SOUND button, you can change the A.H.S.+ (Advanced Hyper Surround plus)
mode, A.T.C. (Advanced Tone Correction), SMART SOUND and HYPER BASS on or off.
A.H.S.+ - Adds a more spacious surround sound. Music gives basic effect and movie for more
effect.
A.T.C. - Reproduces distinctive sounds with tone correction.
SMART SOUND - Decreases high sound levels, giving a regulated sound level.
HYPER BASS - Increases bass levels, giving a richer, deeper bass.
SOUND EFFECT
Press the SOUND button
A.H.S.+
MOVIE MUSIC OFF
ON OFF
π†
To select A.H.S.+, A.T.C., SMART SOUND or
HYPER BASS
A.T.C.
SMART SOUND
HYPER BASS
ON OFF
ON OFF
MENU
è
To choose the setting
OPERATE
EXIT
SELECT
Press the MENU when finished
Notes:
• Smart Sound may become an unnatural effect, depending on the signal source.
• You can adjust BALANCE only when A.H.S.+ is off.
Sub Channel
The main channel sometimes has minor channels (Sub Channels). By using the SUB CH
button, you can select a sub channel easily.
At first, select TV or STB mode to use the Sub channel function. See page 60.
To watch sub channels
For example, to move to sub channel 123-45:
Press 1, 2 and 3 in order
Press the SUB CH button
Press 4 and 5 in order
Press the TUNE button
Note:
• If there are more than 2 major channels, select the digital channel by using the π† buttons
and then press the OK button.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Video Status
The VIDEO STATUS button gives you a choice of four TV picture display settings, including a
display of your own preferences.
VIDEO STATUS
Standard - Resets the picture display to the factory settings.
Dynamic - Gives a vivid picture with better contrast when
viewing in a brightly lit room.
Theater - Gives a rich, film-like look to video when viewing in
a dimly lit room.
STANDARD
DYNAMIC
THEATER
GAME
Game - Used for when you are playing video games connected to your TV.
Press the VIDEO STATUS button
By every press of the VIDEO STATUS button, you change the mode.
Note:
• You can also change the mode by pressing the π† buttons.
• Each mode is memorized for each input connected to the TV.
• You can also access the FRONT PANEL CONTROL screen by using the MENU button on
the front of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has VIDEO STATUS and ASPECT menus. Choose VIDEO
STATUS by pressing MENU
+/- buttons.
†
on the front panel and choose a mode by using the CHANNEL
• There are four video status settings: Dynamic, Standard, Theater and Game. Each video
status setting has a separate memory for HD (1080i/1080p/720p) and SD (480p/480i) video
signal. Each video status can be chosen along with your favorite picture settings (Tint,
Color, Picture, Bright, Detail, etc.)
– When an HD signal is displayed: Your HD settings are recalled for the video status you
are using.
– When an SD signal is displayed: Your SD settings are recalled for the video status you
are using.
– The input you are using (Input-1, Input-2, etc.) does not affect the setting that is recalled,
just the signal type.
– This function considers PC input as an HD signal and TWIN screens as an SD signal.
C.C. (Closed Caption)
Use the C.C. (Closed Caption) button to select the mode of closed caption.
At first, select TV, STB or VCR mode to use the closed caption function. See page 60.
Press the C.C. button
CLOSED CAPTION
OFF
Notes:
SMART CAPTION
• SMART CAPTION will appear when you press the MUTING
ON
button, only on channels where the broadcast contains
closed captioning.
• When you select ON, it will be the mode selected in the Closed Caption Menu.
• See page 40 when you set the caption/text mode.
• You can also change the mode by pressing the π† buttons.
• If you are in PC mode, C.C. can not be used
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Sleep Timer
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work for a total
time of up to 180 minutes.
At first, select TV mode to use the sleep timer function.
Press the SLEEP button
0 15 30 45 60 90 120 180
Sleep Timer Message
60 seconds before the automatic shutoff, this message will appear:
GOOD NIGHT !
PUSH SLEEP TIMER BUTTON
TO EXTEND
You then have 60 seconds to press the SLEEP button to
delay the shut off for another 15 minutes.
ML/MTS
MTS technology allows several audio signals to be broadcast in analog at once, giving you a
choice in what you wish to hear with a TV program. In addition to mono or stereo sound, an
MTS broadcast may also include a second audio program (SAP).
At first, select TV mode to use the multi-language/MTS function.
Press the ML/MTS button
MTS
STEREO
SAP
ON AIR
ON AIR
By every press of the ML/MTS button, you change
the mode
MONO
Notes:
• When you are receiving a digital broadcast, if there are other languages, you can change the
language by pressing the ML/MTS button.
• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo
mode even if a certain broadcast is in mono sound only.
• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.
• MTS unavailable if your television’s Input source is in VIDEO-1, 2, 3, 4 or 5 mode, as
described on page 60.
• ML/MTS will not work when you are using the HDMI.
• You can also change the mode by pressing the π† buttons.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Twin
Activate the split-screen option by pressing TWIN on
the remote control. The channel (or input) you were
watching before pressing TWIN will appear on the left,
the new channel will appear on the right. The sound
will continue to come from the main screen channel
(or input). To turn split-screen off and return to
normal television viewing, press TWIN again or press
the BACK button.
07
V-1
MAIN SCREEN
PICTURE
SPLIT SCREEN
PICTURE
At first, select TV mode to use the TWIN function.
Notes:
• Main Screen and Split Screen will not display the same channel or input at the same time.
• You can enter the TWIN mode when the screen is in NORMAL mode.
• Split screen will not display digital channels.
• Split-screen functions will not work with locked channels or channels blocked by V-Chip
ratings limits. A gray screen will display instead.
• With split screen, the picture from the component terminal and HDMI terminal will not be
displayed.
• The aspect of MAIN CHANNEL PICTURE becomes 16:9 when you input the picture of
480p, 720p and 1080i from the component terminal and HDMI terminal.
• After you press the SELECT button, and select SPLIT SCREEN when you press the
OK button, select normal screen. If you don’t operate, the MAIN CHANNEL SCREEN will
be automatically selected about 8 seconds later.
• Aspect does not work in Twin mode.
• When you press the Menu button in Twin mode, it appears only as Picture Adjust menu.
• When you are in PC mode or 1080p mode, TWIN, SWAP, SELECT and FREEZE can not
be used.
Swap
You can exchange the channel (or input) displayed in the split screen window for the main
screen image by pressing the SWAP button.
At first, select TV mode to use the SWAP function.
Notes:
• It will only work in TWIN mode.
• If the signal that you are watching is coming from the HDMI input, you can not enter the
SWAP mode.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Select
With SELECT, you can select the picture (channel) while viewing TWIN screen. When you
press SELECT button, the channel number on the top will be highlighted. Each press of SELECT
will shift the channel.
At first, select TV mode to use the Select function.
Freeze
Pressing the FREEZE button causes the screen to change to the split-screen display with the still
picture displayed on the right. In order to return to the normal display, press the FREEZE button
once again.
At first, select TV mode to use the Freeze function.
Display
The display screen shows the current status of timers, inputs and XDS ID.
At first, select TV or STB mode to use the display function. See page 60.
Press the DISPLAY button
The screen to the right shows the following
information:
05 KLVX PBS
JAZZ FESTIVAL
• The current channel or AV input (Channel 05)
NOW
12:20 PM
OFF
• The current time (12:20 pm)
• Sleep timer status/minutes remaining (The Sleep
Timer is off)
SLEEP TIMER
ON/OFF TIMER
ON TIME
EVERYDAY
7:00 PM
• On/off timer status (Set to turn on everyday at
7:00 PM, off at 10:00 PM)
OFF TIME
10:00 PM
• Each Press of the DISPLAY button changes the
display mode:
Display
Time
Channel
Off
Display - Full screen shown above
Time - Shows the current time only
Channel - Shows the current channel
Off - Turns display off
Notes:
• You may also turn off the display at any step by pressing MENU.
• If the clock, sleep timer or on/off timer are not set, the display screen will show:
“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.
External device control buttons
You can use this remote control to operate the basic functions of your external devices. See
page 70 on how to program the remote control to operate your other devices.
Note:
• The remote is preset to control JVC-brand devices.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
Remote programming
You can program your remote control to operate your external devices, using the instructions
and codes on pages 70 - 75. The following external devices can be operated using your
remote control.
Device
Mode
Applied for these functions
Page
Cable Set Top Box
STB
Power on/off, Channel up/down, Volume up/down, Number 0 - 9, Tune, Return+/ TV,
Muting, Favorite Channel, Menu on/off, Arrow buttons, OK/Enter, Back, DVR (JVC Only)*,
Guide (EPG), Sub Channel, Closed Caption, Display (Recall),
71
Cable/PVR Combination
Satellite Set Top Box
DBS/PVR Combination
Rewind ( ), Playback ( ), Forward ( ), Record ( ), Stop ( ), Pause ( ).
VCR, DBS/PVR Combination
PVR, DVD/PVR Combination
VCR
DVD
Power on/off, Channel up/down, Menu on/off, Arrow buttons, OK/Enter, Back, Guide (EPG), 72, 73
TV/VCR, Closed Caption, Eject ( ), Rewind ( ), Playback ( ), Forward ( ), Record ( ),
Stop ( ), Pause ( ).
DVD Player, DVD Recorder
Home Theaer in Box
Power on/off, Channel up/down, Menu on/off, Arrow buttons, OK/Enter, Back, Guide (EPG),
TV/DVD (TV/VCR button), Sub Title (Sub T.), Open/Close ( ), Rewind ( ), Playback ( ),
Forward ( ), Record ( ), Stop ( ), Still ( ).
74
Amplifier, Home Theater in Box, AUDIO
Receiver
Power on/off, Audio Input Selection (V1 button), Volume up/down, Muting,
DVD operation buttons: Menu on/off, Arrow buttons, OK/Enter, Back, Sub Title (Sub T.),
Open/Close ( ), Rewind ( ), Playback ( ), Forward ( ), Stop ( ), Still ( ).
75
* DVR button only applies to JVC DVR (Dish Satellite STB).
Notes:
• To record to your VCR or DVD, hold the record ( l ) button on the remote control and press play
( ® ).
• If the code you programmed doesn't work, try the next one. If no codes work, refer to "Search
Code Function" on page 70. If your remote does not work after using the "Search Code Function",
use the remote that came with your device. Your TV remote can not be guaranteed to work with all
models, brands or operations.
• When the television remote control does not operate, for a model that allows you to switch the
remote control code on the device side, you can try switching the setting to default or something
else on the device side
How to set the codes
1) Find your device and device's brand from the code list. See page 70 - 75.
2) Select the mode of your device by pressing the MODE button. Then confirm the mode LED on the
remote control.
3) Press and hold the TUNE button, then enter the first four digit code number listed using the
number buttons. When the code is set, the mode LED goes out for a second, then it lights.
4) After confirming the proper mode LED, release the TUNE button, and confirm the operation of your
device.
5) If your device does not respond, try and enter the next code.
Search Code Function
1) Select a mode of your device by pressing the MODE button.
2) Press the POWER and RETURN+/TV buttons. Hold for at least 3 seconds and release. Then
confirm the mode LED blinks.
3) Press any button* on the remote, and see if the selected device responds. *Use the applied
buttons except for √ ® cursors, Return+/TV and Rec ( l ) on the above chart.
4) If there was a response, press RETURN+/TV. The codes are now set. Then confirm the mode
LED goes out.
5) If there was no response, try to select the previous code or the next code by using √ or ® . If you
repeat a total of 65 times for the STB (90 times for the VCR, 120 times for the DVD and 132 times
for the AUDIO) without a response, use the remote control that came with your equipment. Press
RETURN+/TV to exit. Then confirm the mode LED goes out.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
Programming Codes
STB mode
Cable Set Top Box
Satellite Set Top Box
Satellite Set Top Box
ABC
0003, 0008
0899
0899
1187
0476
0476, 0810, 0276,
0003
0144
0009, 0273
0476, 0810, 0276,
0003
AlphaStar
Chaparral
Coolsat
Crossdigital
DirecTV
0772
0216
1806
1109
Samsung
1377, 1276, 1108,
1109, 1442, 1609
0856
0639, 1639, 1640
0869
1142, 1442
0749, 1749, 0790,
1285
1392, 1640
1806
0724, 0722
1535
1535
0869
Americast
Bell South
Digeo
Director
General Instrument
SKY
Sony
1377, 0392, 0566, Star Choice
0639, 1639, 1142, Tivo
0247, 0749, 1749, Toshiba
0724, 0819, 1856,
1076, 1108, 0099, UltimateTV
1109, 1414, 1442, Ultrasat
1609, 1392, 1640
1505, 1005, 0775, US Digital
1170, 1775 USDTV
1505, 1005, 0775, Voom
GoldStar
Hamlin
Jerrold
Uniden
Memorex
Motorola
0000
Dish Network System
Dishpro
1376, 0476, 0810,
0276, 1187
1877, 0237, 0008
0000, 0008, 0107
0000
1305, 0317, 0025
1877, 0877, 0144, GE
0533
0000
0000
0279, 0273
0000
0000, 0144
1877, 0877, 0477,
0008
1006
0003
0276
0003
Pace
1775
Zenith
0856, 1856
Panasonic
Paragon
Philips
Echostar
1505, 1005, 0775,
1170, 1775
0775, 1775
0566
0869
0775, 1775
1535
DBS/PVR Combination
Expressvu
Pioneer
DirecTV
1377, 0392, 0639,
1142, 1076, 0099,
1392, 1442, 1640
1505, 0775
1505, 0775
1505, 0775, 1170
0775
General Instrument
GOI
Hisense
Hitachi
HTS
Pulsar
Quasar
Regal
Runco
Samsung
Scientific Atlanta
Dish Network System
Dishpro
Echostar
0819
0775, 1775
Hughes Network Systems 1142, 0749, 1749, Expressvu
1442
1790
1535
0775, 1170, 1775
1414
0724, 0722
0724
0749
0869
0869
0247, 0701
1807
0724
1142, 0749, 1749,
0724, 1076, 0722,
0099, 1442
0392, 0566
1535
Hughes Network Systems 1142, 1442
JVC
Motorola
Philips
Proscan
RCA
Samsung
Sony
Star Choice
Humax
iLo
JVC
1170
0869
1142, 0099, 1442
0392
1392
1442
0639, 1640
0869
Sony
Starcom
Supercable
Torx
Toshiba
Zenith
LG
Magnavox
Memorex
Mitsubishi
Motorola
Next Level
Panasonic
Pansat
Paysat
Philips
0000
0000, 0525, 0899
Cable/PVR Combination
Americast
Digeo
General Instrument
Jerrold
Motorola
Pace
Pioneer
Scientific Atlanta
Sony
Supercable
Zenith
0899
1187
0810
0810
1376, 0810, 1187
1877, 0237
1877, 0877
1877, 0877
1006
Proscan
Proton
RadioShack
RCA
0869
0566, 0855, 0143,
1392
0276
0899
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
VCR mode
VCR
VCR
VCR
ABS
1972
0048, 0209
0000
Fisher
Fuji
Funai
Garrard
0047, 0104, 0046
0035, 0033
0000, 0593, 1593
0000
Marta
Matsushita
0037
0035, 0162, 0227,
1162
1972
0035
Admiral
Adventura
Aiko
0278
Media Center PC
MEI
Aiwa
0037, 0000, 0307, Gateway
1972
0479
0041, 0061, 0106
1972
0278
0035
0240
0037, 0278
0240
GE
0060, 0035, 0240, Memorex
0202, 0760, 0761,
0807, 1035, 1060
0432, 0526
0037, 0209, 0038,
0225, 1237
0035, 0162, 0037,
0048, 0039, 0047,
0240, 0000, 0104,
0209, 0046, 0307,
0479, 1037, 1048,
1162, 1237, 1262
0240, 0043, 0061
0240
Akai
Alienware
America Action
American High
Asha
Go Video
GoldStar
Audiovox
Gradiente
Harley Davidson
Harman/Kardon
0000
MGA
Beaumark
Bell & Howell
Broksonic
0000
0081, 0038
0072
MGN Technology
Microsoft
Mind
0104
1972
1972
0184, 0121, 0209, Harwood
0002, 0479, 1479
0037
0035
0020
0081
0072, 0278
0037, 0278, 1278
0072
0037, 0047, 0240, Hughes Network Systems 0042, 0739
0072, 0271
Headquarter
Hewlett Packard
HI-Q
0046
1972
0047
0037, 0240, 0000,
Minolta
Mitsubishi
0042, 0105
Calix
0081, 0067, 0043,
0041, 0061, 0173,
0807
0035, 0048
0240, 0000
Canon
Capehart
Carver
CCE
Citizen
Colt
Hitachi
0042, 0041, 0105, Motorola
1037
1972
1972
MTC
Multitech
NEC
Howard Computers
HP
0000, 0072
0035, 0037, 0048,
0104, 0067, 0041,
0038, 0008
0037
1972
0240
1972
0035
1062, 0162, 0037,
0048, 0104, 0432,
0593, 1048, 1162,
1262
0184, 0121, 0209,
0002, 0208, 0479,
1479
1062, 0035, 0162,
0225, 0227, 0616,
1035, 1162, 1262
0035, 0037, 0240,
0042, 0038, 1035,
1237
Craig
Humax
0739
1972
1972
0041
Curtis Mathes
0060, 0035, 0162, Hush
0041, 0760, 1035
0240
Nikko
Niveus Media
Noblex
iBUYPOWER
Jensen
JVC
Cybernex
CyberPower
Daewoo
1972
0045, 0067, 0041, Northgate
0008, 0366, 1707, Olympus
1945, 1774, 1775, Optimus
1776, 1777
0037, 0278
0067, 0041, 0038
0045, 0104, 0278,
0020, 0046, 0561,
1278
0020
1972
0042
0739
0039, 0038
0000
0037
Daytron
Dell
Denon
DirecTV
Durabrand
Dynatech
Electrohome
Electrophonic
Emerex
KEC
Kenwood
KLH
Kodak
LG
0072
Orion
0035, 0037
0037, 0045, 0042,
0209, 0038, 1037
1972
0000, 0208
0240, 0072
0037
Panasonic
Penney
Linksys
Lloyd's
Logik
0037
0032
Emerson
0035, 0037, 0184, LXI
0240, 0045, 0000, Magnasonic
0121, 0043, 0209, Magnavox
0002, 0278, 1593,
1479, 1278, 0593,
0561, 0479, 0208, Magnin
0593, 1278
0035, 0039, 0081, Pentax
0000, 0149, 0563, Philco
0593, 1593, 1781
0240
0042, 0105
0035, 0000, 0038
0061
Marantz
0035, 0081
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
VCR mode
PVR
VCR
VCR
Philips
0035, 0081, 0000, Symphonic
0563, 0593, 0618, Systemax
0739, 1081, 1181, Tagar Systems
0000, 0593, 1593
1972
1972
Howard Computers
HP
Hughes Network Systems 0739
1972
1972
1266
0037
Tatung
0081, 0045, 0000, Humax
0067, 0041, 0008, Hush
0739
1972
Pilot
Pioneer
Polk Audio
Portland
Presidian
Profitronic
Proscan
0081, 0042, 0067
0081
0020
1593
0240
0060, 0202, 0760, Tivo
0761, 1060
0072
0039
0046
0046
0035, 0162, 1035,
1162
0000, 1037
0037
0037
0366
iBUYPOWER
JVC
Linksys
Media Center PC
Microsoft
1972
1945
1972
1972
1972
1972
1972
1972
0616, 1777
0618, 0739
0880
0614, 0616
0739
0614, 0616
0636, 1972
1972
1972
1972
0618, 0636, 0739
1008, 1972, 1996
1972
Teac
0000, 0041
0035, 0162
0035, 0037, 0000
0000
0618, 0636, 0739, Mind
1996
Technics
Teknika
Thomas
Niveus Media
Northgate
Protec
Pulsar
Quarter
Quartz
Quasar
TMK
Toshiba
0240, 0208
0081, 0045, 0042, Panasonic
0067, 0043, 0041, Philips
0008, 0057, 0366, RCA
0845, 1008, 1145, ReplayTV
1972, 1996
0037, 0240
1972
0240
0045
0038
0045, 0061
0037
Samsung
Sonic Blue
Sony
RadioShack
Radix
Randex
RCA
Totevision
Touch
Unitech
Stack 9
0060, 0035, 0240, Vector
Systemax
Tagar Systems
Tivo
Toshiba
Touch
0000, 0042, 0149, Vector Research
0105, 0106, 0202, Video Concepts
0760, 0761, 0807, Videomagic
0880, 1035, 1060
Videosonic
0240
Realistic
0035, 0037, 0048, Viewsonic
0047, 0000, 0104, Villain
1972
0000
Viewsonic
Voodoo
1972
1972
0046
0614, 0616
1972
Voodoo
Wards
1972
ZT Group
1972
ReplayTV
Ricavision
Runco
0060, 0035, 0048,
0047, 0081, 0240,
0000, 0042, 0072,
0149, 0760
0209, 0072
0035, 0000, 0072
0041, 0038
0039, 0033, 0000,
0209, 0034, 0479,
1139, 1479
1972
DVD/PVR Combination
0000
0039
Samsung
0240, 0045, 0432,
0739, 0760, 1014
0048, 0039
0000, 0067, 0209, Yamaha
0041, 0271, 0479, Zenith
1479
Emerson
White Westinghouse
XR-1000
Sanky
Sansui
Sanyo
Scott
0047, 0240, 0104,
0046
ZT Group
0184, 0045, 0121,
0043
DBS/PVR Combination
1945
Sears
0035, 0037, 0047,
0000, 0042, 0104, Echostar
0046, 0057, 0105, Hughes Network Systems 0739
1237
JVC
1945
0739
0739
Sharp
0048, 0209, 0807, Philips
0848, 1048
0104, 0072
0240
0045, 0072
0614, 0616
0035, 0032, 0033, Alienware
0000, 0034, 0636, CyberPower
0639, 0640, 1032, Dell
1232, 1972
1972
Samsung
Shintom
Shogun
Singer
Sonic Blue
Sony
PVR
ABS
1972
1972
1972
1972
0739
1945
1945
1972
1972
DirecTV
Dish Network System
Echostar
Stack 9
STS
Sylvania
0042
0035, 0081, 0000, Gateway
0043, 0593, 1593, Hewlett Packard
1781
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
DVD mode
DVD Recorder
1416
DVD
DVD
Accurian
Advent
Aiwa
Akai
Alco
1416
1016
0641
0695, 0770, 0899
0790
Magnavox
0503, 0539, 0646, Accurian
0675, 0821, 1268
0539
Apex Digital
1056
1168
1129
0490
0675, 1334
1158
0741, 1158, 1304,
1730
Marantz
Memorex
Microsoft
Mintek
Aspire Digital
CyberHome
Denon
Funai
Gateway
Go Video
0695, 0831, 1270
0522, 1708
0839, 0717
1521, 0521
0741
Allegro
Apex Digital
0869
0672, 0717, 0755, Mitsubishi
0830, 1056, 1061
1023
NAD
NEC
Arrgo
0785
Aspire Digital
Audiovox
Blaupunkt
Blue Parade
Broksonic
Cinea
Cine Vision
Citizen
Coby
1168
0790
0717
0571
0695
0831
0876, 0833, 0869
1277
0778, 1107
0831
Nesa
0717
1402
iLo
JVC
LG
LiteOn
Magnavox
1348
1164
0741
NexxTech
Norcent
Onkyo
Oritron
Panasonic
1003, 1107
0503, 0627
0651
0490, 0703, 1362, Panasonic
1462, 1490, 1762 Philips
0503, 0539, 0646, Pioneer
0675, 0854, 1158, RCA
1260, 1267, 1354
0525, 0571, 0631
1061
0539
0770
0675
1158, 1416, 1440
0646, 0675
0490
0646, 1158
0631
0522
0490, 1470
1158
Philips
Craig
Curtis Mathes
CyberHome
Samsung
Sensory Science
Sharp
Sony
Sylvania
Zenith
1087
Pioneer
0816, 0874, 1023, Polaroid
1024, 1117, 1129 Polk Audio
0784, 0705, 0770, Portland
0833, 0869, 1169, Presidian
0630, 0675
1033, 1431
0675
Daewoo
0741
1172
Prima
1016
Denon
Disney
Durabrand
DVD2000
Emerson
0490, 0634
0675, 1270
1127
0521
0591, 0675, 0821,
1268
Proscan
Pro Vision
Qwestar
RCA
0522
0778
0651
Home Theater in Box
Aiwa
0641
0790
1770, 1771, 1772,
1773
0522, 0571, 0717, Audiovox
0790, 0822, 1022, JVC
1132
Enterprise
ESA
Fisher
Funai
Gateway
GE
Go Video
0591
0821, 1268
0670
0675, 1268, 1334
1158
0522, 0815, 0717
0744, 0715, 0741, Sansui
0783, 0833, 0869, Sanyo
1044, 1075, 1099, Sensory Science
Rio
Rotel
Sampo
Samsung
0869
0623
0752
KLH
Koss
Oritron
0790
0651
0651
0539
0790
0869
0869
0790
0490, 0573, 0744, Polk Audio
0820, 0899, 1044, RCA
1075, 1470
0695
0670, 0695, 0873
1158
Rio
Sonic Blue
Teac
Venturer
0790
1158, 1304, 1730
0741
0717
0582, 0702
0573, 0664, 1247
0672
1500, 1588
1348
0717
1268
0627
0702
Sharp
0630, 0675, 0752,
1256
1117
GoldStar
Greenhill
Harman/Kardon
Hitachi
Hiteker
Humax
iLo
Sharper Image
Sherwood
Shinsonic
Sonic Blue
Sony
0770
0533, 0839
0869, 1099
0533, 1533, 0864,
1033, 1431, 1536
0821
0675, 0821, 1268
0675, 0821
0717, 0790
0490, 0703
0571
Initial
Superscan
Sylvania
Symphonic
Teac
Insignia
Integra
JBL
Jensen
JVC
1016
Technics
0558, 0623, 0867, Theta Digital
1164, 1602, 1770, Tivo
1503
1771, 1772, 1773
0790
0490, 0534
0717, 0790, 1149
0651
Toshiba
0503, 0695, 1045,
1154, 1503, 1515,
1588
0503
0839
Kawasaki
Kenwood
KLH
Urban Concepts
US Logic
Venturer
Xbox
Yamaha
Koss
Lasonic
Lenoxx
LG
0798
1127
0790
0522, 1708
0490, 0539, 0545
0503, 0591, 0741,
0869
0591, 0741, 0869
1058, 1158, 1416, Zenith
1440
LiteOn
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
Audio mode
Amplifier
Receiver
Home Theater in Box
Amstrad
Bose
Curtis Mathes
Durabrand
GE
Harman/Kardon
JVC
Left Coast
Lenoxx
Linn
Marantz
NEC
Optimus
Philips
Pioneer
Polk Audio
RCA
0078
0674
0300
1561
0078
0892
0331
0892
Koss
1366, 1497
1798
1437
1293, 1869
1497
1189, 1269, 0531, Audiovox
1514 Bose
1189, 1269, 0891, Cambridge Soundworks
1289
1393
1751
1389, 1751
1389
0135, 0842, 1298, Durabrand
1320, 1531
1023, 0531, 1074
1366, 1497
1308, 1518, 0367, Insignia
1288, 1316, 1548, Integra
1633, 1763, 1764
1189, 1269, 0891, JVC
1266, 1289, 1673
1023, 0014, 0150, KLH
0531, 0630, 1123, Koss
1384, 1823
1508
Aiwa
1388, 1641
1563, 1615
1563, 1615
1609
1257, 1430
1390
1229, 1933
1370
1352
1389
1420
1250
2832
1561
1517
1532
1426
1751
1298
1306
1374, 1495, 1676,
1871
Lasonic
Lenoxx
LG
Liquid Video
Magnavox
Amphion Media Works
AMW
Anam
Apex Digital
Marantz
1561
Classic
Coby
Criterion
Daewoo
Denon
0269, 0282, 0829
0892, 0269
0264
0300, 0823
0892, 0269
0013, 0300, 0823
0892, 0269
0300, 0823
0264
0689, 0815, 1126
0078
0331
0078, 0013
0354, 0133
Mitsubishi
NexxTech
Norcent
Nova
Onkyo
Gateway
Go Video
Initial
Optimus
Oritron
Panasonic
Shure
Sony
Soundesign
Victor
Wards
JBL
Philips
Yamaha
Pioneer
1390, 1412
1366, 1497
1798
1561
1293, 1869
1497
Lasonic
Lenoxx
LG
Receiver
Polaroid
Polk Audio
ADC
Aiwa
0531
1289, 1414
1254
1405, 0121, 1243, Proscan
Liquid Video
1388, 1641
1512
1390
1563, 1615
1563, 1615
1609, 1074
1257, 1430
1189
RCA
1023, 1609, 1254, Magnavox
0531, 1074, 1123, NexxTech
1514
1751
1389, 1751
1389
1298, 1531
1366, 1497
1288, 1316, 1548,
1633, 1763, 1764
1266, 1673
1384
1508
1289
1609, 1390, 1511
1437
1869
1519
1295, 1500
1469
1556
1517
Akai
Alco
1390, 1511
1437
Norcent
Nova
Amphion Media Works
AMW
Anam
Apex Digital
Audiotronic
Audiovox
Regent
Rio
Saba
Samsung
Sansui
Sanyo
1869
Onkyo
0531, 1519
1295, 1500
1764
Oritron
Panasonic
1390
1251, 1469
0771, 1286
1556
1517, 1653
1426
Philips
Pioneer
Polaroid
Polk Audio
RCA
Bose
1229, 0639, 1841, Sharp
1933
1602
1370
0531
1189
1352
1389
1420
1250
1414
Sharper Image
Brix
Sherwood
Shinsonic
Sirius
Sonic Blue
Sony
Cambridge Soundworks
Capetronic
Carver
Classic
Coby
Criterion
Daewoo
Delphi
1602
1532, 1869
Regent
Rio
1058, 1441, 1258, Saba
1759, 1622, 0474, Samsung
1406, 1558, 1658, Sanyo
1758, 1858, 1958
1023
1313
Sharper Image
Sherwood
Shinsonic
Stereophonics
Denon
1360, 0771, 1142, Sunfire
1426
1660, 2832
0463
1517
Teac
0463, 1074, 1390, Sonic Blue
1532, 1869
0689, 1622, 1558,
1658, 1758, 1858,
1958
Garrard
Gateway
Go Video
1528
Sony
Technics
Thorens
1308, 1518, 1384
1189
1532
Harman/Kardon
0110, 0891, 1304, Toshiba
1788
1390
0014
1406, 1414
0176, 1176, 1276, Zenith
1331, 1375, 1476
0857, 1293
Teac
1390, 1528
1788
1390
1331, 1375
1293
1306
1426
1751
Venturer
Wards
XM
Toshiba
Venturer
Yamaha
Initial
Insignia
Integra
JBL
0135, 1298, 1320
0110, 1306
Yamaha
JVC
0531, 1374, 1495, Zenith
1560, 1676, 1871,
1894
Kenwood
KLH
1313, 1570, 1569
1390, 1412
75
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Information
Weak Signal
This OSD warning appears when the digital channel that you have selected is too weak to
receive or no signal is being detected for that channel.
Weak Signal
15
No Program
If the external input terminal you selected, or were watching is not receiving a signal, "NO
PROGRAM" appears on the television screen. It appears when that external input terminal
is not receiving a signal and you have the Noise Muting function OFF and you have a single
screen. It moves automatically every two seconds to prevent the screen from burn-in.
Note:
• Even if "NO PROGRAM" appears on the screen, your timer functions and auto shut off
functions that you set, are still active.
Invalid Signal
If you are inputting a PC signal that is invalid, "Invalid Signal" will appear on the TV screen. It
appears when the input is PC and it is a single screen.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Replacement
Lamp Message
If this message appears when you turn the TV
on, you need to replace the lamp. See page 78
on how to replace the lamp.
LAMP NEEDS TO BE REPLACED.
REFER TO OWNER'S MANUAL FOR
REPLACEMENT INSTRUCTIONS.
Note:
AFTER REPLACING THE LAMP,
PLEASE RESET TIMER IN THE TV
MENU.
• This message will appear every time you
turn on the TV when the lamp needs to be
replaced. Press the OK button to make the
message disappear, or replace the lamp.
PRESS OK, IF YOU DO NOT WANT
TO SEE THIS MESSAGE AGAIN.
Lamp Warning
It is very important that you NEVER TOUCH THE GLASS SURFACE OF THE NEW
LAMP. Touching the glass surface will deposit oils from your hand onto the lamp
surface. When the lamp heats up to its operating temperature, the oil will cause a
difference in temperature on the lamp surface that will likely cause the lamp to break.
Replace the lamp with part number PK-CL120U only! The television is designed
to work specifically with this lamp. Using a different lamp, or a third-party
manufacturer’s lamp could cause a malfunction and or damage to the television.
This television uses a 120-Watt high-pressure mercury lamp to project images onto the
television screen. When the lamp nears the end of its operating life, you may notice the picture
becoming dark. When the picture begins to darken, or the lamp burns out, it is time to replace
the lamp. The following instructions will tell you how to safely replace the lamp.
Under operating conditions, THE LAMP WILL GET EXTREMELY HOT AND WILL
CAUSE SEVERE BURNS IF TOUCHED.
Before attempting to replace the lamp, make sure the television has completely run
through its cooling cycle. Turn the power off and wait until the LAMP LED blinks very
slowly and turns off completely. Unplug the TV. If you feel any warmth as you place
your hand near the lamp, DO NOT TOUCH IT. Wait until the lamp has completely
cooled before attempting to replace it. After turning the power off, wait at least 1 hour
or more.
NEVER attempt to replace the lamp with the television plugged into a wall outlet.
Attempting to replace the lamp with the TV plugged in could lead to a severe electrical
shock.
Do not keep the TV on for more than 24 hours consecutively. There is the possibility
of the life of the lamp being shortened.
The life of the lamp changes depending on the atmospheric temperature and altitude
in which the TV is being used.
Please read these instructions fully before attempting to replace the lamp. If you feel
unsure about replacing the lamp yourself, call a service technician.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Replacement
Replacement Lamp Kit
Before replacing the lamp, you will need to purchase a replacement kit, part number
com.
The replacement kit will include the following:
1 High-Pressure Mercury Lamp
1 Instruction Manual
Because the lamp contains a small amount of mercury, it cannot be disposed of with
normal trash.
How to Replace the Lamp
Please read these instructions fully before attempting to replace the lamp. If you feel
unsure about replacing the lamp yourself, call a service technician. Please observe all
safety warnings.
DO NOT attempt to remove the assembly until the lamp has fully cooled. If you feel any heat
near the lamp, STOP and wait until the lamp has FULLY COOLED.
NEVER attempt to remove the lamp with the television plugged into an outlet.
DO NOT DROP the used lamp. The inside of the lamp is under pressure. Dropping or other
hard shock could cause the lamp to shatter.
ALWAYS recycle the used lamp. Because the lamp contains a small amount of mercury, it
cannot be thrown away with regular trash. Follow the recycling instructions included with the
Lamp Replacement Kit.
1) Turn off the television.
Press the POWER button on the remote control or TV front panel. Wait until the picture has
closed and the LAMP LED on the front panel has stopped blinking indicating the lamp cool
down is complete.
Warning: The cool-down process cools the lamp from its operating temperature. This
does not mean that the lamp will now be cool enough to handle safely. We strongly
recommend you wait at least one hour before proceeding.
2) Unplug the television.
Disconnect the power cord from the AC outlet. Make sure that the LAMP LED light has stopped
blinking before you unplug the set. Never attempt to replace the lamp with the television
plugged in.
3) Remove the lamp cover.
The lamp is located behind the lamp cover below the left side
of the television. To access the lamp you will need to remove
the lamp cover. First, remove the screw located on the lamp
cover using a Phillips head type screwdriver (cross-head type).
Once the screw has been removed, gently pull it towards you
and the panel will come away from the television. Set it aside.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Replacement
4) Remove the lamp unit.
Using a Phillips head type screwdriver (cross-head type), loosen the two screws fastening the
lamp unit. When the screws have been loosened, remove the lamp by raising the handle and
gently sliding the unit towards you. Place it carefully in the recycling packaging.
5) Install the new lamp unit.
Holding the handle attached to the new lamp unit, slide and push the new lamp into the
television and back into the lamp housing area. Do not forget to re-tighten the two screws.
Note: If the lamp does not sit securely in the TV (in the lamp housing area), it won’t turn on.
Make sure the lamp sits securely in the housing area.
WARNING!
Remember it is very important that YOU DO NOT TOUCH THE LAMP SURFACE. Please
read the warnings on page 77 again.
Also, replace the lamp with part number PK-CL120U only! The television is designed
to work specifically with this lamp. Lamps other than PK-CL120U may cause
malfunctions and/or other damage to the television.
NOTICE (for USA)
This product has a High Intensity Discharge (HID) lamp that
contains a small amount of mercury. It also contains lead in some
components. Disposal of these materials may be regulated in your
community due to environmental considerations. For disposal or
recycling information, please contact your local authorities, or the
To purchase a replacement lamp kit, please call 1-800-252-5722.
6) Re-install the lamp cover.
Insert the lamp cover in the right concave and close the lamp cover. Because the lamp cover
has a role to help prevent the danger of an electrical shock, tighten the screw using a Phillips
head type screwdriver (cross-head type).
Notes:
• Make sure the lamp door is closed completely, or the power will not turn on.
• After installing the new lamp unit, do not forget to reset the lamp timer. See page 58.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Replacement
Warning LED Messages
While the power is on, and there is a problem with the TV, the TV changes to warning
mode and informs you of the problem using the LED as follows. Then, the power turns off
automatically and performs the cooling for approximately 40 seconds.
The LAMP LED blinks
Condition: It may be a malfunction of the internal electrical circuits.
To correct: Keep the TV off for a while and then turn the power on again. If the TV goes into
warning mode, unplug the TV after the cooling has completed and consult your
dealer.
The POWER LED and LAMP LED blink alternately
Condition: The inside temperature rises abnormally or the fan may be blocked.
To correct: Keep the TV off for a while and then turn the power on again. If the TV goes into
warning mode, unplug the TV after the cool down as completed and consult your
dealer.
The POWER LED and LAMP LED blink rapidly simultaneously
Condition: The lamp unit has been installed on a slant, or it is not fully inserted into the lamp
housing. Or it may be a lamp malfunction.
To correct: • If this condition occurs soon after replacing the lamp: Reinstall the new lamp unit.
Repeat the lamp installation steps, taking care to observe all warnings. Make
sure the lamp sits securely inside the unit when you reinstall it.
• If this condition occurs except for replacing the lamp: Keep the TV off for a while
and then turn the power on again. If the TV goes into warning mode, unplug the
TV after the cool down as completed and consult your dealer.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
CHECK
PROBLEMS
There is no power
• See if the power cord became unplugged.
• Check for a blown fuse or circuit breaker or a power outage.
• It is possible the fan is stuck or the inside temperature is rising abnormally.
Consult your dealer.
The POWER LED
and LAMP LED are
blinking alternately.
• It may be a malfunction that the fan is locked or the temperature has increased.
The POWER LED
and LAMP LED
are blinking rapidly
simultaneously.
• The lamp may not have been installed correctly, or it may be due to a malfunction.
• The lamp door may not be closed correctly.
There is no picture
or sound
• The antenna could be disconnected.
• The input mode could be set improperly. See page 60.
• The tuner (Auto Tuner Setup) could be set improperly. See page 30.
• The TV station may be having difficulties. Check to see if other stations are working.
• Use the HDMI cable with HDMI logo
. See page 20.
• You can not output audio using the AUDIO OUTPUT under the following conditions:
1) When you have digital sound from an HDMI device connected to the INPUT-1 or
INPUT-2 connection on the side of your TV. (See page 20).
2) When you have analog sound from a DVI device connected to the
AUDIO IN "INPUT-1" connection. (See page 19).
Remote control is not • Check to see that the batteries are still working and properly installed.
operating properly or • Make sure the remote has a clear sight path to the TV.
at all
• You may be too far from the TV. You must be within 23 feet (7 meters).
• Make sure your remote is set to the proper mode. See page 60.
You cannot select a
certain channel
• Make sure the channels have been programmed. See "Channel Summary", page 31.
• Check to see if the channel is locked. See "Channel Summary - Lock" page 32.
The power turns off
by itself
• Make sure the set did not become unplugged.
• Perhaps the On/Off Timer is set. See page 57.
• Check to see if the Sleep Timer was set. See page 67.
It does not operate
correctly
• This television is operated by a microprocessor. It is possible that external noise or
interference is causing the problem. If the television does not function correctly, remove the
electrical plug from the wall outlet and wait a while before inserting it into the wall outlet
again and operating the television.
The clock is wrong
• The power was interrupted and the clock was not reset. See page 56.
The color quality
is poor
• Tint and Color may be improperly adjusted. See page 51.
• The Video Status mode may be turned to the wrong setting. See page 66.
There are lines
across the picture
• There could be interference from another electrical appliance, such as a computer,
another TV or VCR. Move any such appliances further away from the TV.
• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
operating nearby. Move the antenna away from the appliance or change to a coaxial
cable connection which is less prone to interference.
The picture is spotted
There are double
pictures (ghosts)
• A building or passing airplane can reflect the original signal and produce a second,
slightly delayed one. Adjust your antenna position.
Picture is snowy
(image noise)
• Your antenna may be damaged, disconnected or turned. Check the antenna
connection. If the antenna is damaged, replace it.
Screen is 80% black
• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 66.
• Make sure the MTS settings are correct. See page 67.
Stereo or bilingual
programs can't be
heard
The LAMP LED
continues blinking
• It may be a malfunction of the internal electrical circuits.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
CHECK
PROBLEMS
Static electricity
• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional
crackling sounds
• It is normal for the TV to make crackling sounds when first turned on or off. Unless
the sound or picture become abnormal, this is fine.
The following are not malfunctions.
• The television may make a creaking sound if the temperature of the room or the temperature
inside the television changes. If there is no problem with the screen or sound, then there is no
need to worry.
• The lamp may make a noise when it blows, but this is not dangerous.
• The lamp may make a noise when the power is turned on and a picture is displayed on
the screen. This noise is caused when the mercury inside the lamp is heated, and is not a
malfunction.
• The still parts of a picture may remain on the screen. This is a characteristic of HD-ILA
elements and not a malfunction. The picture will disappear over time.
• The operation of this television is not guaranteed below 0ºC. If the power is turned on while
the temperature is below 0ºC, the picture may be disturbed. Use the television when the
temperature is 0ºC or higher.
• Although the HD-ILA element is manufactured with high-precision technology, please
understand that some pixels may be lost or permanently displayed.
• There is a cooling fan built-in to the television. Please understand that this fan will make some
noise when the television is on and while cooling.
• Although the picture may be temporarily disturbed and noise may be seen on the screen if the
power is turned on immediately after it has been turned off. This is not a malfunction.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
HD-58S998
Model
Type
HD-ILA Device Projection
NTSC, BTSC System (Multi-Channel Sound)
ATSC Terrestrial, Digital Cable
Reception Format
Reception Range
VHF 2 to 13, UHF 14 to 69 at ATSC,
CATV 125 Sub, Mid, Super, Hyper and Ultra bands at Digital Cable
VHF 2 to 13, UHF 14 to 69 CATV 125 Sub, Mid, Super, Hyper
and Ultra bands (181 channel frequency synthesizer system) at Analog
•
Reception of channel A-5 ("95" of the TV set's on-screen cable channel
numbers) is not recommended for your TV set.
Power Source
Power Consumption
Projection Source
AC 120V, 60 Hz
219W
120W High-Pressure Mercury Lamp
58 inch / 147 cm
measured diagonally,
16:9 ratio
Screen Size
Speakers
(1 cm x 9.5 cm) x 2, 10 cm round x 1
Audio Output
Full Range - 10W + 10W + 10W
Antenna Terminal
(VHF/UHF,
ATSC/DIGITAL
CABLE IN)
75 ohms (VHF/UHF)(F-type connector)
S (Input 3)
Input 3, 4, 5
Terminal
Y: 1 Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
Video: 1 Vp-p, 75 ohms
Audio: 500 mVrms (-4dBs) high impedance
Input 3, 4 Terminal
(component terminal)
1080i / 720p / 480p / 480i
Y: 1 Vp-p positive, 75 ohms (negative sync provided)
PB/PR: 0.7 Vp-p 75 ohms
Video: 1080p / 1080i / 720p / 480p / 480i / VGA
Audio: 2ch PCM, 32 / 44.1 / 48 KHz 16 / 20 / 24 bit
Input 1, 2 Terminal
(HDMI Input Terminal)
•
Personal computer compatibility cannot be guaranteed.
Audio Output Jacks
(FIX)
FIX : 500mVrms (-4dBs) Low impedance (1000 Hz when modulated 100%)
Digital Out (optical) x 1
Optical Output
Digital Audio
Analog RGB D-SUB (15 pin) x 1
• PC signal is available. Refer to page 23 for details on the signals which
can be input.
Input 5 Terminal
(PC Input Terminal)
51 1/2 x 37 7/8 x 13 5/8
130.5 x 96.1 x 34.6
With Front and Rear
Pedestal
Dimensions (inch)
W X H X D (cm)
51 1/2 x 37 7/8 x 10 3/4
130.5 x 96.1 x 27.2
Without Front and Rear
Pedestal
Weight (lbs / kg)
118.8 / 54
With Front and Rear
Pedestal
114.7 / 52
Without Front and Rear
Pedestal
Accessories
Illuminated remote control unit x 1 / AA batteries X 2
Front Pedestal x 1 / Rear Pedestal x 1
Philips type screws x 14
Specifications subject to change without notice.
• The open source software is embedded in this product. For more information, please go to:
83
Download from Www.Somanuals.com. All Manuals Search And Download.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
87
Download from Www.Somanuals.com. All Manuals Search And Download.
JVC COMPANY OF AMERICA
Division of JVC Americas Corp.
1700 Valley Road
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada, M1X 1A7
Wayne, New Jersey, 07470
Download from Www.Somanuals.com. All Manuals Search And Download.
|