Projection Television Users Guide
For Models:
AV-56P785
AV-56P775
AV-48P775
Illustration of AV-56P775 and RM-C14G
Important Note:
In the spaces below, enter the model and serial number of your television (located
at the rear of the television cabinet). Staple your sales receipt or invoice to the
inside cover of this guide. Keep this user’s guide in a convenient place for future
reference. Keep the carton and original packaging for future use.
Model Number:
LCT1676-001B-A
1204TNH-II-IM
Serial Number:
Download from Www.Somanuals.com. All Manuals Search And Download.
This product incorporates copyright protection technology that is protected by U.S. patents
and other intellectual property rights. Use of this copyright protection technology must
be authorized by Macrovision, and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is
prohibited.
Important Safeguards
CAUTION:
Please read and retain for your safety.
Electrical energy can perform many useful functions. This TV set has been engineered and
manufactured to assure your personal safety. But improper use can result in potential
electrical shock or fire hazards. In order not to defeat the safeguards incorporated in this
TV set, observe the following basic rules for its installation, use and servicing. Also follow all
warnings and instructions marked on your TV set.
INSTALLATION
(POLARIZED-TYPE)
1 Your TV set is equipped with a polarized AC line plug (one
blade of the plug is wider than the other). This safety feature
allows the plug to fit into the power outlet only one way.
Should you be unable to insert the plug fully into the outlet,
try reversing the plug. Should it still fail to fit, contact your
electrician.
2 Operate the TV set only from a power source as indicated on the TV set or refer to the
operating instructions for this information. If you are not sure of the type of power supply to
your home, consult your TV set dealer or local power company. For battery operation, refer
to the operating instructions.
3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords
and broken plugs. They may result in a shock or fire hazard. Call your service technician for
replacement.
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV set
where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not use this TV set near water — for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near swimming pool, etc.
6 If an outside antenna is connected to the TV set, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna discharge unit, connection
requirements for the grounding electrode.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
7 An outside antenna system should not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRICAL
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
NEC - NATIONAL ELECTRIC CODE
8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during
operation to be released.
Therefore:
— Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa,
rug, etc.
— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided.
— Never cover the openings with a cloth or other material.
— Never place the TV set near or over a radiator or heat register.
9 To avoid personal injury:
— Do not place a TV set on a sloping shelf unless properly secured.
— Use only a cart or stand recommended by the TV set manufacturer.
— Do not try to roll a cart with small casters across thresholds or deep pile carpets.
— Wall or shelf mounting should follow the manufacturer’s instructions, and should use a
mounting kit approved by the manufacturer.
Use
10 Caution children about dropping or pushing objects into the TV set through cabinet
openings. Some internal parts carry hazardous voltages and contact can result in a fire or
electrical shock.
11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an aerosol
cleaner.
12 Never add accessories to a TV set that has not been designed for this purpose. Such
additions may result in a hazard.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTABLE CART WARNING
(Symbol provided by RETAC)
13 For added protection of the TV set during a lightning storm or when the TV set is to be left
unattended for an extended period of time, unplug it from the wall outlet and disconnect the
antenna. This will prevent damage to product due to lightning storms or power line surges.
14 A TV set and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the TV set and cart combination to overturn.
Service
15 Unplug this TV set from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the TV set.
C. If the TV set has been exposed to rain or water.
D. If the TV set does not operate normally by following the operating instructions. Adjust
only those controls that are covered in the operating instructions as improper adjustment
of other controls may result in damage and will often require extensive work by a
qualified technician to restore the TV set to normal operation.
E. If the TV set has been dropped or damaged in any way.
F. When the TV set exhibits a distinct change in performance — this indicates a need for
service.
16 Do not attempt to service this TV set yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
17 When replacement parts are required, have the service technician verify in writing that the
replacement parts he uses have the same safety characteristics as the original parts. Use
of manufacturer’s specified replacement parts can prevent fire, shock, or other hazards.
18 Upon completion of any service or repairs to this TV set, please ask the service technician
to perform the safety check described in the manufacturer’s service literature.
19 When a TV set reaches the end of its useful life, improper disposal could result in a picture
tube implosion. Ask a qualified service technician to dispose of the TV set.
20 Note to CATV system installer.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as practical.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Screen Burn-in
Displaying fixed images on your screen for extended periods of time can leave a subtle but
permanent ghost image in your screen. This is referred to as "burn-in". To avoid this, mix your
viewing patterns and aspect modes from time to time..
Examples include, but are not limited to the following:
• Stock-market report bars
For example...
• Shopping channel logos and pricing displays
• Video game patterns or scoreboards
• Bright station logos
TV off
TV on
• Internet web sites or other computer-style
images.
• DVD discs, video tapes, laser discs
• Broadcast, cable, satellite channels or digital
television tuners/converters.
• Aspect modes that leave solid black bars
on the top and bottom, or both sides of the
screen.
XYZ
XYZ
Note: Warranty DOES NOT cover screen
burn-in or uneven picture tube aging.
Caring for the Cabinet
Normally, light dusting with a soft, non-scratching duster will keep your TV clean.
If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly
moistened with water. You can add a few drops of mild liquid detergent to the water to help
remove spots of oily dirt.
• DO NOT allow liquid to enter the TV through the ventilation slots.
• DO NOT use strong or abrasive cleaners on the TV.
• DO NOT spray liquids or cleaners directly on the TV’s surface.
• DO NOT rub or scrub the TV harshly. Wipe the set gently with a soft cloth.
Caring for the Screen
The screen is treated with an electrostatic-proof coating. When it gets dirty, wipe it gently with a
soft cloth. If the screen is very dirty, wipe it down with a cloth dipped in a diluted kitchen cleaner
and thoroughly wrung-out. Then wipe immediately after with a clean, dry cloth.
Do not apply alcohol, organic solvents (like acetone), acidic or alkaline cleansers to the screen.
These will remove the coating layer and cause discolorations.
Do not push or hit the screen. This could cause scratches on the screen surface and image
distortions.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Safety Precautions . 2
Warnings . . . . . . . . . . . . 6
Quick Setup . . . . . . . . . . . 9
Sound Adjust . . . . . . . . . 57
Sound Settings . . . . . . . . . . . . . 57
Adjust Sound Settings . . . . . . . . . 57
Reset . . . . . . . . . . . . . . . . . . 57
Unpacking your TV . . . . . . . . . . . . 9
TV Models . . . . . . . . . . . . . . . . 11
TV Remote Control . . . . . . . . . . . 12
Getting Started . . . . . . . . . . . . . 13
The Remote Control . . . . . . . . . . 13
Connecting Your Devices . . . . . . . 14
Interactive Plug In Menu . . . . . . . . 25
Clock Timers . . . . . . . . . . 58
Set Clock . . . . . . . . . . . . . . . . 58
On/Off Timer . . . . . . . . . . . . . . . 59
Button Functions . . . . . . . 60
Multi Screen Function . . . . . . . . . . 60
Twin . . . . . . . . . . . . . . . . . . 60
Index . . . . . . . . . . . . . . . . . 61
Freeze . . . . . . . . . . . . . . . . . . 61
Swap . . . . . . . . . . . . . . . . . 61
Select . . . . . . . . . . . . . . . . . . 61
Power . . . . . . . . . . . . . . . . . . 62
Number Buttons . . . . . . . . . . . . . 62
Remote Programming . . . . . 28
Setting CATV, VCR and DVD Codes . . . 28
CATV or Satellite Codes . . . . . . . . 28
VCR Codes . . . . . . . . . . . . . . 29
DVD Codes . . . . . . . . . . . . . . 30
Search Codes . . . . . . . . . . . . . 31
Tune
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
62
Input . . . . . . . . . . . . . . . . . . . 62
Channel +/- . . . . . . . . . . . . . 62
Volume +/- . . . . . . . . . . . . . 62
Return +/TV . . . . . . . . . . . . . . . 63
Sound . . . . . . . . . . . . . . . . . . 63
Video Status . . . . . . . . . . . . . . . 64
Natural Cinema . . . . . . . . . . . . . 64
TheaterPro D6500K . . . . . . . . . . . 64
Sleep Timer . . . . . . . . . . . . . . . 65
ML/MTS . . . . . . . . . . . . . . . . . 65
Muting . . . . . . . . . . . . . . . . . . . 65
Display . . . . . . . . . . . . . . . . 66
C.C. . . . . . . . . . . . . . . . . . . . 66
Favorite . . . . . . . . . . . . . . . . 67
Aspect . . . . . . . . . . . . . . . . . 68
Aspect Ratios . . . . . . . . . . . . . 68
Menu . . . . . . . . . . . . . . . . . . 69
OK . . . . . . . . . . . . . . . . . . . 69
Back . . . . . . . . . . . . . . . . . . . 69
TV/CATV Slide Switch . . . . . . . . . . 70
VCR/DVD Slide Switch . . . . . . . . . 70
VCR Buttons . . . . . . . . . . . . . . . 70
DVD Buttons . . . . . . . . . . . . . . . 70
Light . . . . . . . . . . . . . . . . . . . 70
Super Focus . . . . . . . . . . . . . . . 70
Onscreen Menus . . . . . . . . 32
Using the Guide . . . . . . . . . . . . . 32
Onscreen Menu System . . . . . . . . . 33
Initial Setup . . . . . . . . . . 35
Auto Tuner Setup . . . . . . . . . . . . 35
Channel Summary . . . . . . . . . . . . 36
Channel Label . . . . . . . . . . . . 37
V-Chip . . . . . . . . . . . . . . . . . . 38
Set Lock Code . . . . . . . . . . . . . 43
Adjusting CRT Color Conversion . . . . . 44
Auto Demo . . . . . . . . . . . . . . . 46
Language . . . . . . . . . . . . . . . . 46
Closed Caption . . . . . . . . . . . . . 47
Auto Shut Off . . . . . . . . . . . . . . 49
XDS ID . . . . . . . . . . . . . . . . . 49
Noise Muting . . . . . . . . . . . . . . 49
Front Panel Lock . . . . . . . . . . . . 50
V1 Smart Input . . . . . . . . . . . 50
Video Input Label . . . . . . . . . . 51
Position Adjustment . . . . . . . . . . . 52
Power Indicator . . . . . . . . . . . . . 52
Digital-In . . . . . . . . . . . . . . . . . 53
Digital-In Audio . . . . . . . . . . . . . 53
Center CH Input . . . . . . . . . . . . . 54
Video-1 Monitor Out . . . . . . . . . . 54
Picture Adjust . . . . . . . . . 55
Picture Settings . . . . . . . . . . . . . 55
Adjust Picture Settings . . . . . . . . . 55
Color Temperature . . . . . . . . . . . . 55
Digital Noise Clear . . . . . . . . . . . . 56
VSM . . . . . . . . . . . . . . . . . . . 56
Reset . . . . . . . . . . . . . . . . . . 56
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents (Continued...)
Digital Setup . . . . . . . . . . . 71
Digital Setup . . . . . . . . . . . . . . . 71
Antenna Level . . . . . . . . . . . . . 71
Digital Sound . . . . . . . . . . . . . . 72
Aspect Ratios . . . . . . . . . . . . . . 72
Cable Card Application . . . . . . . . . 73
i.LINK Auto Play . . . . . . . . . . . . 73
Software Update . . . . . . . . . . . . 73
Digital Button Functions . . . 74
Digital CH D/A (Digital/Analog) . . . . . 74
Sub Channel . . . . . . . . . . . . . 74
i.LINK Menu . . . . . . . . . . . . . 75
Timer . . . . . . . . . . . . . . . . 77
Guide . . . . . . . . . . . . . . . 79
OSD Information . . . . . . . . 80
Weak Signal . . . . . . . . . . . . . 80
Cable Card Information . . . . 81
Cable Card Connection . . . . . . . . 81
Appendices . . . . . . . . . . 82
No Program . . . . . . . . . . . . . . 82
Troubleshooting . . . . . . . . . . . . . 83
Warranty . . . . . . . . . . . . . . . . . 84
Authorized Service Centers . . . . . . . 85
Specifications . . . . . . . . . . . . . . . 86
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Unpacking your TV
Thank you for your purchase of a JVC Color Television. Before you begin setting up your new
television, please check to make sure you have all of the following items. In addition to this
guide, your television box should include:
AA
Remote Control x 1
Television x 1
Batteries x 2
POWER
TV CATV VCR DVD
ASPECT
MULTI SCREEN
TWIN
INDEX SELECT SLEEP
FREEZE
SWAP ML/MTS DISPLAY
+
INPUT
1
4
2
5
8
0
3
6
D/A
i.LINK MENU
7
9
RETURN+
TV
TIMER
TUNE
THEATER
PRO
VIDEO
SUB
CHANNEL
FAVORITE
STATUS
SUB
NATURAL
CINEMA
SOUND
LIGHT
C.C.
MUTING
GUIDE
Note: Your television
and/or remote
CH
VOL
VOL
OK
CH
MENU
BACK
DIGITAL IMAGE SCALING TECHNOLOGY
VCR CHANNEL
PREV NEXT
VCR DVD
POWER TV VCR
control may differ
from the examples
illustrated here.
POWER
PROGRAM
PULL/OPEN
REW
PLAY
FF
REC
STOP
PAUSE
OPEN CLOSE
STILL PAUSE
RM-C14G
RF Cables x 2
Splitter x 2
2-WAY SPLITTER
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Unpacking your TV
Once you have unpacked your television, the next step is to connect it to your antenna/
cable or satellite system and to connect the audio/video devices you want to use with your
television. To make these connections you will use plugs like the ones illustrated below.
Component Cables
Composite Cables
Audio Cables
Coaxial Cables
Used to connect an
external antenna or
cable TV system to
your TV.
Used to connect audio/
video devices like
VCRs, DVD players,
stereo amplifiers, game
consoles, etc.
S-Video Cable
AV CompuLink Cable
Used to make video
connections with S-Video
VCRs, Camcorders and
DVD players.
Used to connect JVC
AV CompuLink capable components
for an automated home theater.
We recommend that before you start using your new television, you read your entire User’s
Guide so you can learn about your new television’s many great features. If you’re anxious to
start using your television right away, a quick setup guide follows on the next few pages.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
TV Models
NOTE: Before you connect your television to another device, please refer to the proper
diagrams for your specific TV and remote. These will help assist you in understanding
how to connect your television to another device, as well as use the remote to set up
your television.
Rear Panel Diagram
UNPLUG THE POWER CORD FROM AC OUTLET
BEFORE REMOVING THE REAR COVER
When the rear cover is removed, follow "CAUTION AT DISASSEMBLY" procedure in the
service manual before plugging the TV's power cord into an AC outlet. Failure to
follow the procedure will result in PERMANENT damage to some of the television
features.
MODELS:
DÉBRANCHEZ LE CORDON DE LA PRISE DE COURANT
AV-56P785
AV-56P775
AV-48P775
C.A. AVANT DE RETIRER LE COUVERCLE ARRIÈRE.
Une fois le couvercle arrière déposé suivez la procédure
««ATTENTION LORS DU DÉMONTAGE»» décrite dans la manuel de service avant
de brancher le cordon du téléviseur dans une prise c.a. L'omission de suivre la
ATSC
/DIGITAL CABLE IN
procédure causera des dommages PERMANENTS
à
certaines fonctions du téléviseur.
Licensed by BBE Sound, Inc. under USP4638258, 5510752 and 5736897.
BBE and BBE symbol are registered trademarks of BBE Sound, Inc.
Sous licence de BBE Sound, Inc. BBE et le symbole BBE sont des marques déposées
de BBE Sound, Inc.
SERVICE ONLY
Licenciado de BBE Sound, Inc. BBE
de BBE Sound, Inc.
y
el simbolo de BBE son marcas registradas
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
MACROVISION PATENT NUMBERS U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,
093; and 6,516,132. LICENSED FOR LIMITED PAY-PER-VIEW USES ONLY.
LC32925-001A-A
CABLE CARD
Note: The terminal
labeled "SERVICE
ONLY", is exclusively
used to update the
software version.
R
AUDIO
(ANALOG)
i.LINK IN/OUT
S400(TS)
L
VIDEO
(DIGITAL)
OPTICAL OUT
Digital Audio
AUDIO
(DIGITAL)
DIGITAL IN
VIDEO INPUT–2 INPUT–1
Y
CENTER
CHANNEL
INPUT
INPUT-3
INPUT-2
INPUT-1
OVER
L
R
Pb
75Ω (VHF/UHF)
AUDIO
L
R
Pr
OVER
R
L
MONITOR
/REC OUT
S-VIDEO
AV COMPULINK III
COMPONENT VIDEO
AUDIO OUT
AUDIO
VIDEO
Front Panel Diagram
IN
P
U
T
-
O
4
S-VI
DE
VIDEO
R
O
V
E
A
U
DIO
O
L
/
M
ON
R
I
I
DIGITAL IM
AGE SCALING
MENU
CHANNEL
TECHNOLOG
–
+
Y
PO
W
PO
ER
VOLUME
W
ER
–
+
O
PER
PR
AT
E
OG
SUPER
FOCUS
PR
OG
RA
M
RA
M
PU
LL
PU
LL
/OP
EN
/O
PE
N
Pull to open the door
PULL/OPEN
DIGITAL IMAGE SCALING TECHNOLOGY
POWER
PROGRAM
PULL/OPEN
INPUT- 4
S-VIDEO VIDEO
AUDIO
MONO
OVER
L
/
R
MENU
CHANNEL
VOLUME
SUPER
FOCUS
–
+
–
+
OPERATE
MODELS: AV-56P785, AV-56P775, AV-48P775
Note: When you have set a REC timer or VIEW timer, a PROGRAM indicator will light on the
front panel. While a timer is set, the indicator light will not turn off even if you turn the power
off. See page 77.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
TV Remote Control
POWER
TV CATV VCR DVD
ASPECT
MULTI SCREEN
TWIN
INDEX SELECT SLEEP
FREEZE
SWAP ML/MTS DISPLAY
+
INPUT
1
4
2
5
8
0
3
6
D/A
i.LINK MENU
7
9
RETURN+
TV
TIMER
TUNE
THEATER
PRO
VIDEO
SUB
CHANNEL
FAVORITE
STATUS
SUB
NATURAL
CINEMA
SOUND
LIGHT
C.C.
MUTING
GUIDE
CH
VOL
VOL
OK
CH
MENU
BACK
VCR CHANNEL
PREV NEXT
VCR DVD
POWER TV VCR
REW
PLAY
FF
REC
STOP
PAUSE
OPEN CLOSE
STILL PAUSE
RM-C14G
RM-C14G
MODELS:
AV-56P785
AV-56P775
AV-48P775
• For information on remote control buttons, see pages 60-70 and 74-80.
• i.LINK MENU, TIMER, SUB CHANNEL, FAVORITE and GUIDE buttons are for digital
channels. If your TV is connected to an ATSC antenna or Digital Cable, you can use these
buttons.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Getting Started
Getting Started
These quick setup pages will provide you, in three easy steps, with the basic information you
need to begin using your new television right away.
If you have questions, or for more detailed information on any of these steps, please consult
other sections of this manual.
Step 1 – The Remote Control
Before you can operate your remote
control, you first need to install the
batteries (included).
Slide the cover on the back of the
remote down towards the bottom of
the remote control. Insert two batteries
(included) carefully noting the “+” and
“–” markings, placing the “–” end in the
unit first. Slide the cover back into place.
When you change the batteries, try to complete the task within three minutes. If you take
longer than three minutes, the remote control codes for your VCR, DVD, and/or cable
box/satellite receiver may have to be reset. See pages 28 - 31.
Key Feature Buttons
The four key feature buttons at the center of the remote can be
MUTING
GUIDE
used for basic operation of the television. The top and bottom
buttons will scan forward and back through the available
channels. To move rapidly through the channels using
JVC’s Hyperscan feature, press and hold CH+ or CH–. The
channels will zip by at a rate of five channels per second. The
right and left buttons will turn the volume up or down. These
buttons are also marked with four arrows and are used with
JVC’s onscreen menu system. To use the onscreen menus,
press the MENU button.
CH
OK
CH
VOL
VOL
MENU
BACK
Basic Operation
Turn the television on and off by pressing the POWER button at the top right corner
of the remote. If this is the first time you are turning on the TV, the interactive
plug-in menu appears.
POWER
T
• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if
you need to operate a cable box.
TV CATV
VCR DVD
• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to
DVD to control a DVD player. Please see pages 28 to 31 for instructions on
programming your remote control to operate a cable box, VCR or DVD player.
A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Step 2 – Connecting Your Devices
Notes:
• These connections are examples.
• After you are finished connecting your devices, plug the power cord into the nearest power
outlet and turn on the TV.
• To connect a DVD player, see VCR Connection. A DVD player is optional
• If you have a satellite television system, refer to the satellite TV manual.
No VCR Connection
Cable or Antenna
Output
Two-way Splitter
(Attachment)
IN
OUT OUT
Coaxial Cable
(Attachment)
ATSC
/DIGITAL CABLE IN
75Ω (VHF/UHF)
TV Rear Panel
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
VCR Connection
Notes:
• Green, blue and red are the most common colors for DVD cables. Some models may vary
colors. Please consult the user’s manual for your DVD player for more information.
• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete
one set of connections (DVD or audio output) before starting the other to avoid accidentally
switching the cables.
• You may also connect the DVD player to Input 1.
Cable or Antenna
Diagram #1
Output
VCR
R
L
V
IN
I
OUT
OUT
IN
Two-Way
Splitter
OUT OUT
Coaxial Cable
(Attachment)
(Attachment)
ATSC
/DIGITAL CABLE IN
OR
Coaxial Cable
(Attachment)
VIDEO INPUT-2 INPUT-1
CENTER
CHANNEL
INPUT
INPUT-3
Y
OVER
TV Rear Panel
L
R
L
INPUT-2
INPUT-1
75Ω (VHF/UHF)
AUDIO
R
OVER
MONITOR
/REC OUT
S-VIDEO
AV COMPULINK III
COMPONENT VIDE
AUDIO OUT
AUDIO
VIDEO
Y
P
P
Green
Blue
B
R
AUDIO OUT
Red
OU
R
L
DVD Player (OPTIONAL)
Note:
• If this connection setup does not work for you, try the connection setup on page 16.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Diagram #2
Cable or Antenna
Output
IN
Two-Way
OUT OUT
Splitter
Coaxial Cable
IN
OUT OUT
Two-Way
Splitter
(Attachment)
Coaxial Cable
(Attachment)
VCR
Coaxial Cable
(Attachment)
R
L
V
IN
IN
OUT
OUT
ATSC
/DIGITAL CABLE IN
OR
VIDEO INPUT-2 INPUT-1
Y
CENTER
CHANNEL
INPUT
INPUT-3
OVER
L
R
INPUT-2
INPUT-1
75Ω (VHF/UHF)
AUDIO
L
R
OVER
MONITOR
/REC OUT
S-VIDEO
AV COMPULINK III
COMPONENT VIDE
AUDIO OUT
UDIO
VIDEO
TV Rear Panel
Y
P
P
Green
Blue
B
R
AUDIO OUT
Red
OU
R
L
DVD Player (OPTIONAL)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to Monitor/Recording Output Terminal
VIDEO INPUT-2 INPUT-1
CENTER
CHANNEL
INPUT
INPUT-3
Y
OVER
TV Rear Panel
L
R
L
INPUT-2
INPUT-1
Pb
Pr
75Ω (VHF/UHF)
UDIO
R
OVER
R
L
S-VIDEO
AV COMPULINK III
COMPONENT VIDEO
AUDIO OUT
AUDIO
VIDEO
OR
IN
IN
OUT
OUT
VCR
Notes:
• When you this connection, Set the Video-1 Monitor Out menu to ON. See page 54.
• If you are receiving ATSC/Digital Cable signal, it can be outputted to the S-Video output
terminal or Video (composite video) terminal.
• If you are receiving Analog TV signal, it can not be outputted to the S-Video output terminal.
• No signal will be outputted through the S-Video output terminal when you are not viewing
images coming from the composite video input terminal.
• No signal will be outputted through the Monitor/Recording output terminal when you are
viewing images from the component video input.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to JVC AV Compu Link
JVC’s AV CompuLink feature makes playing video tapes or DVDs totally automatic. Simply
insert a pre-recorded tape into your JVC brand VCR or DVD into your JVC DVD player and
the device will automatically turn on and begin playback. At the same time, using the
AV CompuLink, the VCR or DVD player sends a signal to the television telling it to turn on
and switch to the proper video input.
• The AV CompuLink cable may be included with the JVC AV CompuLink unit you
wish to connect. If it is not, contact JVC Parts Department at (800)-882-2345, or
• AV CompuLink can only be used with JVC brand products.
To Connect: Plug one end of the AV CompuLink cable
AV CompuLink Cable
into the AV COMPULINK INPUT on your VCR, DVD,
or other CompuLink device. Plug the other end of the
AV CompuLink cable into the AV COMPULINK at the
rear of the television.
Note:
• The AV CompuLink cable has a male 3.5 mm (mono)
plug on each end.
VCR
TV Rear Panel
IN
V
L
R
IN
AV COMPULINK III
OUT
OUT
AV CompuLink
Notes:
• In order for the VCR playback to begin automatically, the recording tabs must be removed
from the VHS tape. If the tab is in place, automatic switching will occur when you push the
VCR’s PLAY button.
• If your JVC brand VCR has “A code/B code remote control switching” (see your VCR’s
instruction book), using VCR A code will switch the TV to input 1.
• Refer to your DVD instruction book for detailed connection information.
• To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see
the receiver connection instructions for detailed connection information.
• AV CompuLink is compatible with select AV CompuLink receivers.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to a Camcorder
You may connect a camcorder, game console or other equipment to your television by using
the front input jacks (Input 4) located under the front panel door. To access, pull on the door
to open it. You can also connect these using the television’s rear input jacks, using the same
instructions.
INPUT- 4
S-VIDEO VIDEO
AUDIO
MONO
OVER
L
/
R
MENU
CHANNEL
VOLUME
SUPER
FOCUS
–
+
–
+
OPERATE
CAMCORDER
- OR -
1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on
the front of the TV, OR connect an S-Video cable from the front of the TV to the camcorder.
2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on
the front of the TV.
3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on
the front of the TV.
Note:
• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the
LEFT AUDIO IN on the front of the TV.
Connecting to an External Amplifier
Speaker
Speaker
CENTER
CHANNEL
INPUT
Amplifier
75Ω (VHF/UHF)
AV COMPULINK III
AUDIO OUT
TV Rear Panel
1) Connect a white composite cable from the LEFT AUDIO OUTPUT on the back of the TV to
the LEFT AUDIO INPUT on the amplifier.
2) Connect a red composite cable from the RIGHT AUDIO OUTPUT on the back of the TV to
the RIGHT AUDIO INPUT on the amplifier.
Notes:
• Refer to your amplifier’s manual for more information.
• You can use AUDIO OUTPUT for your home theater system.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to the Surround Amplifier
In multi-channel sound such as 5.1 channel, the speech characters are played back from the
center speaker.
A center speaker in a movie theater is set in back of the screen so it can recreate a
conversation scene in the movie more natually. By using your TV's speaker as the center
speaker, you can obtain the same sound effect as in a movie theater in you home theater
sound system.
Front
Front
Surround
TV Rear Panel
CENTER
CHANNEL
INPUT
R
75Ω (VHF/UHF)
L
AV COMPULINK III
AUDIO OUT
CENTER CHANNEL OUTPUT
1) Connect the Pin cable from the TV's CENTER CHANNEL INPUT terminal to the surround
amplifier's CENTER CHANNEL OUTPUT terminal.
Note:
• Please read the benefit of this feature on page 54.
Connecting to an amplifier using your optical output
You can connect an amplifier that has an optical digital input terminal by using an optical digital
cable from the optical output. The signal that is output can be PCM or Dolby Digital.
Television Rear Panel
Amplifier
OPTICAL OUT
Digital Audio
1) Connect the optical cable from the back of the television to the back of the amplifier.
Notes:
• This terminal can only output digital audio.
• In order to use the optical output connection, select PCM or Dolby Digital on Digital Sound in
the Digital Setup Menu. See page 72.
• Refer to your owners manual on using your amplifier.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to a Digital TV Receiver
By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in
their digital form.
DTV Decoder
DIGITAL OUT
AUDIO OUT
R
L
R
L
AUDIO
(ANALOG)
VIDEO
(DIGITAL)
AUDIO
(DIGITAL)
DIGITAL IN
HDMI to DVI Cable
TV Rear Panel
After the connections have been made,
tighten the screw to secure the cables.
1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to
the DIGITAL-IN on the back of your television.
2) Connect a red cable from the DTV decoder RIGHT AUDIO OUT, to the RIGHT AUDIO DIGI-
TAL-IN on the back of your television.
3) Connect a white cable from the DTV decoder LEFT AUDIO OUT, to the LEFT AUDIO DIGI-
TAL-IN on the back of your television.
• The digital-in terminal is not compatible with the picture signal of a personal computer.
• Use a HDMI to DVI cable (commercially available) in order to digitally connect the television
with a DTV decoder.
Notes:
• If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance
may be slightly shifted. Access the “DIGITAL-IN” in the initial setup menu to adjust it. (Refer
to page 53.)
• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to
ANALOG. See "DIGITAL-IN AUDIO", page 53.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to an HDMI Compatible Device
By connecting an HDMI compatible device, high definition pictures can be displayed on your
TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI
compatible device.
HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all
digital audio/video interface. HDMI provides and interface between any audio/video source,
such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a
digital television (DTV).
HDMI Compatible Device
DIGITAL OUT
AUDIO OUT
L
R
R
L
AUDIO
(ANALOG)
VIDEO
(DIGITAL)
AUDIO
(DIGITAL)
DIGITAL IN
HDMI Cable
TV Rear Panel
1) Connect the HDMI Cable from the DIGITAL OUT on the back of your DTV or HDMI device, to
the DIGITAL-IN on the back of your television.
Notes:
• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to
DIGITAL. See "DIGITAL-IN AUDIO", page 53.
• Some decoders may not respond depending on the equipment that you have connected
when it is connected to the HDMI.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to an AV Receiver using your television's
V1 Smart Input
By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture
sources from many different devices, without having to change or use the other input
connections on your TV. This allows you to free up the other input connections so you can
connect more devices to your television.
AV Receiver
MONITOR
Y
OUT
VIDEO PUTPUT–1
P
b
INPUT-3
INPUT-2
INPUT-1
Y
OVER
L
Pb
Pr
P
r
AUDIO
R
MONITOR OUT
OVER
R
L
MONITOR
/REC OUT
S-VIDEO
COMPONENT VIDEO
AUDIO
VIDEO
TV Rear Panel
1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1
on the back of your television.
2) Connect a Yellow Composite Cable from the AV Receiver's MONITOR OUT, into the VIDEO
INPUT-1 on the back of your television.
3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y
VIDEO INPUT-1 on the back of your television.
4) Connect a Blue Component Cable from the AV Receiver's Pb MONITOR OUT, into the Pb
VIDEO INPUT-1 on the back of your television.
5) Connect a Red Component Cable from the AV Receiver's Pr MONITOR OUT, into the Pr
VIDEO INPUT-1 on the back of your television.
Note:
• Please refer to your AV Receiver instruction manual for more information on connecting your
speakers and other devices like a DVD player.
• Use your AV Receiver's remote to switch to the different devices you have connected.
• Some AV Receivers may not respond when the V1 Smart Input function is turned on.
• If you have video connections for each input device connected to your AV Receiver, you
should not connect them using both S-Video and Composite connection at the same time
when you are using V1 Input as the V1 Smart Input. In this case we recommend using the
S-Video connection.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting an i.LINK compatible device to the back of
your television
i.LINK is a digital serial interface that allows devices equipped with an i.LINK connector to
exchange digital video signals, digital audio signals and device control signals bi-directionally
over a single cable. (For example, a JVC D-VHS VCR).
i.LINK refers to the IEEE1394-1995 industry specification and extensions thereof. The
is used for products compliant with the i.LINK standard.
logo
This projection television uses a four-pin i.LINK connector to input and output MPEG2 video
signals, audio signals and control signals.
TV Rear Panel
i.LINK IN/OUT
S400(TS)
i.LINK Compatible Device
1) Connect the i.LINK cable from the back of the television to the back of the i.LINK
compatible device.
Notes:
• Use only the S400 i.LINK cable when connection your devices.
• See page 75 on how to select the i.LINK device.
• Refer to your owners manual on using your i.LINK device.
• When recording or playing back video with an i.LINK device, if you perform the Auto Tuner
Setup, the video signal you are recording or playing back may stop or you may not be able
to perform the Digital Auto Tuner Setup.
• Your television can connect with i.LINK D-VHS decks and HD-Camcorders (JVC brand only).
If you connect other brand devices, with i.LINK cable, they will not work.
• It can play only the recorded contents in Digital Mode.
• Use only tapes bearing the DVHS (SVHS) mark for recording.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Plug-In Menu
Step 3 – The Interactive Plug In Menu
When you turn your television on for the first time the interactive plug-in menu will appear. The
plug-in menu helps you to get your TV ready to use by letting you set your preferences for:
• The language in which you want the onscreen menus to appear.
• Setting the TV’s clock to the correct time so your timer functions will work properly. You can
choose “AUTO” or “MANUAL” for setting the clock.
• The auto tuner setup of which channels you wish to receive.
We recommend you complete the interactive plug-in items before you start using your
television.
Notes:
• The interactive plug-in menu setting does not appear if your TV has been turned on before.
In this case use the onscreen menus to perform these settings. See pages 46, 58 and 35.
• If you press the Menu button while setting up the interactive plug-in menu, it will skip over it.
Language
After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically
switches to the LANGUAGE settings. You can choose to view your onscreen menus in three
languages: English, French (Français) or Spanish (Español).
è To choose a language:
LANGUAGE/LANGUE/IDIOMA
(English, Français or Español)
†
To NEXT (To set clock)
ENGLISH
NEXT
MENU
SELECT OPERATE
EXIT
(To be continued...)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Plug-In Menu
Auto Clock Set
Before you use any of your TV’s timer functions, you must first set the clock. You may
precisely set your clock using the XDS time signal broadcast by most public analog
broadcasting stations. If you do not have this in your area, you will have to set the clock
manually. See manual clock set below. To set the clock using the XDS signal:
è
†
To choose AUTO
To TIME ZONE
SET CLOCK
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or
Hawaii)
MODE
AUTO
--: ----
TIME
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/04
ON
†
è
†
To move to D.S.T. (Daylight Savings Time)
To turn D.S.T. ON or OFF
To NEXT (To Auto Tuner Setup)
NEXT
MENU
SELECT OPERATE
EXIT
Notes:
• D.S.T. can be used when it is set to ON in the SET CLOCK menu.
• Only when the MODE is set to AUTO, the Daylight Savings Time feature automatically
adjusts your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00
am on the first Sunday in April. The clock will move back one hour at 2:00 am on the last
Sunday in October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
Manual Clock Set
To set your clock manually (without using the XDS signal), choose MANUAL. If you choose
AUTO, see auto clock set above.
è
†
To choose MANUAL
To TIME
SET CLOCK
è
†
To set the hour
To minute
MODE
MANUAL
TIME
--: ----
è
†
To set the minute
To TIME ZONE
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/04
ON
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or
Hawaii)
START CLOCK
SELECT OPERATE
MENU
EXIT
†
To DATE/YEAR
è
†
To set the month
To day
è
†
To set the day
To year
è
†
è
†
To set the year
To move to D.S.T. (Daylight Savings Time)
To turn D.S.T. ON or OFF
To START CLOCK
Note:
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
(To be continued...)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Plug-In Menu
Auto Tuner Setup
In auto tuner setup, the TV automatically scans through all available channels, memorizing the
active ones and skipping over blank ones or channels with weak signals. This means when you
scan (using the CHANNEL +/– buttons) you will receive only clear, active channels. There are
two tuner modes to choose from, ANALOG or DIGITAL.
è
To choose CABLE or AIR (or SKIP when
you skip Analog Auto Tuner Setup)
AUTO TUNER SETUP
IN ANALOG
TUNER MODE
IN DIGITAL
AIR
π†
To TUNER MODE (IN DIGITAL)
ATSC
TUNER MODE
è
To choose ATSC or Digital Cable (or SKIP
when you skip Digital Auto Tuner Setup)
†
To START
START
SELECT OPERATE
After Analog Auto Tuner Setup is finished, Digital Auto
Tuner Setup starts.
MENU
EXIT
NOW
PROGRAMMING !
Now Programming...
20
48
When the setup is finished, "THANK YOU ! SETUP IS NOW COMPLETE" is displayed. Your
quick setup is now complete. You can now begin watching your television, or you can continue
on in this guide for more information on programming your remote control, or using the
JVC onscreen menu system to customize your television viewing experience.
Notes:
• If you want to cancel the Auto Tuner Setup, press the MENU button.
• Noise muting will not work during Auto Tuner Setup.
• If you choose SKIP, it finished without doing the Auto Tuner Setup.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending
on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is
normal.
The Quick Setup is complete
STOP
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
Setting the CATV, VCR and DVD Codes
You can program your remote to operate your cable box, satellite receiver, VCR or DVD
player by using the instructions and codes listed below. If the equipment does not respond
to any of the codes listed below or to the code search function, use the remote control
supplied by the manufacturer.
Cable Box or Satellite Codes
The remote control is programmed with cable box and satellite codes for power on/off,
channel up/down, and 10 key operation.
1) Find the cable box or satellite brand from the list of codes shown below.
2) Slide the 2-way selector switch to “CATV”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the cable box/satellite receiver.
• If your cable or satellite box does not respond to the first code, try the others listed. If it does
not respond to any code, try the search codes function, on page 31.
Cable Box
Codes
024
Digital
Satellite
Systems
Codes
Cable Box
Codes
ABC
Puser
RCA
032
Archer
032, 025
051, 032
022, 051
058, 059
024, 032, 025
029
061, 070
032
Echostar
(Dish Network) 115
100, 113, 114,
Cableview
Citizen
Curtis
Realistic
Regal
058, 064, 040,
041, 042, 045,
068
Express VU
G.E.
100, 113
106
Diamond
Eagle
Regency
034
G.I.
108, 120, 121,
122
Rembrandt
037, 032, 051,
038
Eastern
GC Brand
Gemini
General
Instrument/Jerrold 026, 027, 020,
021, 022, 057,
034
032, 051
022, 043
065, 024, 025,
Gradiente
Hitachi
112
Samsung
051
104, 111
Scientific Atlanta 057, 058, 059
SLMark
051, 047
051, 056
032, 051
HNS (Hughes)
104
Sprucer
Stargate
Magnavox
102, 103
023, 072, 074
Panasonic
Philips
105
Hamlin
040, 041, 042,
045, 058, 064
049, 024
Telecaption
Teleview
Texscan
Tocom
067
102, 103, 116
Hitachi
Macom
047, 051
044
Primestar
108
049, 050, 051,
054
Proscan
RCA
106, 109, 110
106, 109, 110
035, 036, 066,
074
Magnavox
033
Sony
107
030
Memorex
Movietime
Toshiba
Unika
050, 048
032, 025
Star Choice
Toshiba
104, 108
032, 051
039, 037, 048
101, 104, 117,
118, 119
Oak
Universal
Videoway
Viewstar
Zenith
022, 032
052
Panasonic
055, 056, 060,
071, 073
Uniden
102, 103
Paragon
Philips
063
029, 030
063, 046
046
028, 029, 030,
052, 053, 031,
069
Zenith/Drake
Satellite
Pioneer
Pulsar
047, 062
051, 032
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
VCR Codes
The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward,
rewind, pause, record, channel up/down operation.
1) Find the VCR brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the VCR.
• If your VCR does not respond to the first code, try the others listed. If it does not respond to
any of the codes, try the search codes function on page 31.
• After you program your remote, some VCR buttons may not work properly. If so, use the
VCR’s remote.
• To record, hold down the REC button on the remote and press PLAY.
Codes
035
027, 032, 095
Codes
Codes
VCR
Admiral
VCR
VCR
Marantz
Marta
003, 004, 005
064
Samsung
037, 060, 062,
033, 089
Aiwa
Akai
Samtron
Sansui
089
029, 072, 073, Memorex
074
024, 067
003, 026, 020,
052
038, 040, 047,
048, 041, 042
MGA
Audio Dynamic 003, 005
Sanyo
Scott
063, 067, 091,
071
Bell & Howell
Broksonic
Canon
063, 071
020, 026, 094
023, 025
043
Minolta
058, 045, 093
Mitsubishi
038, 040, 047,
048, 041, 042,
078, 090
059, 060, 062,
067, 038, 040,
047, 048, 026,
020
CCE
Multitech
NEC
047, 027, 062
Citizen
064
003, 004, 005,
000
024, 023
Sears
063, 064, 065,
066, 058
Craig
063, 029, 064
Curtis Mathes
045, 024, 027,
093
Olympic
Sharp
035, 036, 080,
088
Optimus
028, 021, 035,
064
026, 020
Daewoo
043, 059, 024,
092
003, 004, 005
Shintom
075
Orion
DBX
Signature 2000 027, 035
Panasonic
023, 024, 021,
022
Dimensia
Emerson
045, 093
Singer
Sony
075
043, 026, 077,
061, 025, 042,
020, 076
Penney
024, 058, 045,
063, 003, 004,
005, 093
028, 029, 030,
053, 054, 055
SV 2000
Sylvania
027
Fisher
Funai
063, 066, 067,
065, 071, 091
Pentax
Philco
058, 005, 045,
093
031, 023, 024,
027
027, 026, 020,
000
031, 024, 027,
023, 026, 020,
043
Symphonic
Tashiro
Tatung
027, 081
064
033, 045, 024
G.E.
003, 004, 005
Philips
031, 023, 024,
086
Go Video
037, 051, 049,
050, 089
Teac
003, 004, 027,
005
Pioneer
Proscan
023
Goldstar
064
Technics
Teknika
021, 022, 023,
024
045, 058, 023,
024, 031, 046,
059, 060, 093,
033, 087
Gradiente
083, 084, 081,
000, 001
024, 027, 070
Hitachi
023, 045, 058,
093, 027, 081
Thomson
Toshiba
033, 096
Quasar
021, 022, 023,
024
Instant Replay 024, 023
059, 046, 079
Radio Shack
033, 024, 063,
036, 067, 040,
027
Jensen
JVC
003
Vector Research 005
003, 004, 005,
000, 001, 002,
006, 007
Wards
Yamaha
Zenith
035, 036, 067,
044, 064
033, 045, 058,
023, 024, 031,
046, 059, 060,
083, 084, 085,
087, 093, 096
RCA
063, 003, 004,
005
Kenwood
003, 004, 064,
005
044, 082, 064,
094
LG
064
Realistic
024, 063, 036,
067, 040, 027
LXI
027, 064, 058,
065, 066, 063,
067
Magnavox
031, 023, 024,
086
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
DVD Codes
The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward,
rewind, previous/next chapter, tray open/close, and still/pause operation.
1) Find the DVD player brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the DVD player.
• If your DVD player does not respond to the first code, try the others listed. If it does not
respond to any of the codes, try the search codes function on page 31.
• After you program your remote, some DVD buttons may not work properly. If so, use the
DVD player’s remote.
DVD Player
Aiwa
Codes
DVD Player
Mintek
Codes
057
DVD Player
Sharp
Codes
028
043
Apex
040, 054,
055
Mitsubishi
025
Silvania
038
Bose
058
Next Base
Onkyo
056
SMC
Sony
048
024, 045,
046, 047
Denon
020, 037
041, 052
Funai
038
032
053
Oritron
044
Technics
Thomson
Toshiba
020
021
023
Go–Video
Panasonic
Philips
020
Harman
Kardon
023, 036
Hitachi
JVC
031
Pioneer
Polk Audio
Raite
022
036
033
Venturer
Vialta
051
050
000
Kenwood
035, 020
Wave
042
Yamaha
Zenith
020, 049
027, 032
KLH
051
039
050
RCA
021, 026
034
Konka
Koss
Sampo
Samsung
030
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
Search Codes
Cable/Satellite Search Codes Function
1) Slide the first 2-Way Mode Selector switch to CATV.
2) Press the POWER and RETURN+/TV buttons. Hold for at least three seconds and release.
3) Press the POWER button on the remote, and see if the cable or satellite box responds.
4) If there was a response, press RETURN+/TV. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use
the remote control that came with your equipment.
5) Press RETURN+/TV to exit.
VCR/DVD Search Codes Function
1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR” or
“DVD”.
2) Press the VCR or DVD POWER and RETURN+/TV buttons. Hold for at least three seconds
and release.
3) Press the VCR or DVD POWER button, and see if the VCR or DVD responds.
4) If there was a response, press RETURN+/TV. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times for the VCR (40 times for
the DVD player), and there is no response, use the remote control that came with your
equipment.
5) Press RETURN+/TV to exit.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Using the Guide
Certain symbols are used throughout this guide to help you learn about the features of your
new television. The ones you will see most frequently are:
π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–
buttons let you:
• Move vertically in a main menu screen
• Move through a submenu screen
• Move to the next letter, number, or other choice in a submenu
• Back up to correct an error
• Scan through TV channels (when not in a menu screen)
è Left and right arrows mean press the VOLUME+ or VOLUMEРbuttons to move left or right
to:
• Select a highlighted menu item
• Select an item in a submenu
• Select numbers in certain menu options
• Turn the volume up or down (when not in a menu screen)
The “press button” icon means you should press the button named on your remote
control. (Button names appear in SMALL CAPITAL LETTERS.)
The “helping arrow” icon points to the highlighted or selected item in a menu.
To bring up the onscreen menu, press the MENU button on the remote control. The item that
appears in green is the one currently selected. If you use the Menu button on the TV’s front
panel instead of the remote, an additional menu screen showing INPUT, VIDEO STATUS and
ASPECT will appear between INITIAL SETUP and PICTURE ADJUST. The “interactive plug-in
menu” will appear the first time the TV is plugged in.
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SET LOCK CODE
CONVERGENCE
AUTO DEMO
OFF
(4/5)
NEXT PAGE
MENU
SELECT OPERATE
EXIT
Note:
• Menus shown in this book are illustrations, not exact replications of the television’s onscreen
displays.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
The Onscreen Menu System
Your television comes with JVC’s onscreen menu system. The onscreen menus let you make
adjustments to your television’s operation simply and quickly. Examples of the onscreen
menus are shown on the next page. Detailed explanations on using each menu follow later in
this guide. For information about the interactive plug-in Menu, see pages 25 - 27.
The Onscreen Menu System
To open the onscreen menu system, press the MENU button on the remote control. You
navigate within the onscreen menus by using the four directional arrow buttons on the remote
control. (These buttons are also the CH +/– and VOL +/– buttons. Channel and volume functions
will not operate when the onscreen menu is active).
The selected feature and option on a menu screen are highlighted in a different color.
Selected Option
(Green)
ENG. FRAN. ESP.
LANGUAGE
Selected Option
(Blue)
CLOSED CAPTION
To move to a different feature use the π† arrows to move up or down the list. When you
press the up arrow at the top of the list or the down arrow at the bottom, the next menu screen
will appear. Use the arrows √ ® to select an option from the highlighted feature. Pressing
MENU on the remote control will close the onscreen menu system and return you to normal
television viewing.
Each menu and its features will be discussed in the following pages of this guide.
Notes:
• If you do not press any buttons for about a minute, the onscreen menu will automatically
shut off.
• Button names in this guide are shown in SMALL CAPITAL LETTERS.
• Menus may appear in different sizes onscreen depending on the aspect ratio selected.
• Some menu items may not appear in menu screens when certain aspect ratios or inputs
are selected.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Press the MENU button
TO INITIAL SETUP 03
INITIAL SETUP
INITIAL SETUP
/
CLOCK TIMERS
PREVIOUS
SET CLOCK
PREVIOUS
PREVIOUS
DIGITAL-IN
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SIZE1
DIGITAL
ON
DIGITAL-IN AUDIO
/
ON OFF TIMER
CENTER CH INPUT
VIDEO-1 MONITOR OUT
SET LOCK CODE
CONVERGENCE
AUTO DEMO
OFF
OFF
(4/5)
NEXT PAGE
NEXT PAGE
(1/5)
NEXT PAGE
MENU
MENU
SELECT OPERATE
EXIT
SELECT OPERATE
EXIT
MENU
SELECT OPERATE
EXIT
INITIAL SETUP 04
CLOCK/TIMERS
INITIAL SETUP 01
INITIAL SETUP
INITIAL SETUP
SOUND ADJUST
PREVIOUS
PREVIOUS
PREVIOUS
DIGITAL SETUP
NOISE MUTING
ON
OFF
ON
BASS
00
00
00
FRONT PANEL LOCK
V1 SMART INPUT
TREBLE
BALANCE
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
LOW
(2/5)
RESET
NEXT PAGE
(5/5)
EXIT
NEXT PAGE
NEXT PAGE
MENU
MENU
MENU
SELECT OPERATE
SELECT OPERATE
EXIT
SELECT OPERATE
EXIT
INITIAL SETUP 05
SOUND ADJUST
INITIAL SETUP 02
PICTURE ADJUST
INITIAL SETUP
ENG. FRAN. ESP.
PICTURE ADJUST
PREVIOUS
PREVIOUS
LANGUAGE
STANDARD
PREVIOUS
DIG. NOISE CLEAR
VSM
STANDARD
TINT
OFF
ON
00
00
00
00
00
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
COLOR
PICTURE
BRIGHT
DETAIL
OFF
ON
COLOR TEMPERATURE
NEXT PAGE
RESET
HIGH
(1/2)
EXIT
NEXT PAGE
(2/2)
NEXT PAGE
(3/5)
MENU
MENU
MENU
SELECT OPERATE
SELECT OPERATE
EXIT
SELECT OPERATE
EXIT
PICTURE ADJUST 02
INITIAL SETUP 03
PICTURE ADJUST 01
TO INITIAL SETUP 04
Notes:
• The DIGITAL-IN menu can only be displayed when a 480p picture signal is input to the
digital-in terminal and the picture is being displayed on the screen.
• When the Menu button on the TV side panel is pressed, the FRONT PANEL CONTROL menu
between INITIAL SETUP 05 and PICTURE ADJUST 01 will appear.
• Regarding the digital setup menu, see page 71.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Auto Tuner Setup
The auto tuner setup function is described on page 27 as the interactive plug-in menu. If you
need to run the auto tuner setup again, follow the steps below.
Press the MENU button
AUTO TUNER SETUP
IN ANALOG
π†
è
π†
è
π†
è
To AUTO TUNER SETUP
TUNER MODE
IN DIGITAL
AIR
To operate
ATSC
TUNER MODE
To TUNER MODE (IN ANALOG)
To choose CABLE, AIR or SKIP
To TUNER MODE (IN DIGITAL)
To choose ATSC, DIGITAL CABLE or SKIP
PRESS OK TO START
SELECT OPERATE
MENU
EXIT
Press the OK button to start
Programming will take approximately 2 to 4 minutes. The auto tuner is finished when the
message PROGRAMMING OVER! appears onscreen.
Press the Menu button when finished
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Channel Summary
Channel summary allows you to customize the line-up of channels received by your TV.
Regarding analog channels, you can add or delete channels from the line-up or prevent any
unauthorized viewers from watching any or all 191 channels. Regarding digital channels, the
only channels that will appear are the ones that are broadcasting.
Press the MENU button
To CHANNEL SUMMARY
To operate
Analog Channels
CHANNEL SUMMARY
π†
CHNO. SCAN
ID
CHNO. SCAN
ID
è
01
06
HBO
The Channel summary screen will now be displayed with
the channels set to scan marked with an “√”. Regarding
analog channels, you can delete channels from the scan
by removing the “√”. If any channels were missed during
auto tuner setup and you wish to add them, you may by
placing an “√” next to the channel number.
02
03
04
05
MTV
07
08
09
10
L
A&E
E!
OK
MENU
SELECT
OPERATE
EXIT
Digital Channels
• Digital channels can not be added to the channel
summary if the auto tuner setup did not find them.
Channel Summary Digital
CH No.
D01
Scan
Station Name
FOX
π†√® To the SCAN column
Press the OK button to include or delete from
scan
D02
ABC
D02
CNN
D10-1
D10-2
D12345
NBC
BOX
Press the MENU button when finished
NHK
BACK
MENU
Operate
Back
Exit
Note:
• The number of a digital channel may change,
depending on the time of some broadcastings. If
this channel existed and now had disappeared, the
lock channel or scanned channel by the channel
summary for that channel will be cancelled.
Note:
• When the Cable Card is not
inserted into the Cabe Card
Slot:
If you are watching analog
channels, the above screen
appears.
If you are watching digital
channels, the below screen
appears.
• When the Cable Card is
inserted into the Cabe Card
Slot:
Below screen appears
Both analog and digital
channels are listed, but the
background video is not
displayed.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
How to set the channel label. (This is only for analog broadcasting.)
Press the MENU button
ID
π†
è
π†
To CHANNEL SUMMARY
To operate
To the ID column
CHANNEL 09
RESET
Press the OK button to enter
OK
PRESS TO FINISH
è
π†
To select the character you want
To move to the next space
MENU
SELECT OPERATE
EXIT
...continue to follow these directions for all four
spaces
Press the OK button to finish
Your characters are now set
Press the MENU button when finished
If you want to reset the characters you set:
Press the MENU button
π†
è
π†
To CHANNEL SUMMARY
To operate
To the ID column
Press the OK button to enter
To select RESET
π†
Press the OK button to finish
Your characters are now reset
Notes:
• You can use characters for: Alphabet, numbers, marks and spaces.
• It is possible to set the maximum of 40 channel labels.
• If you try to set more than the 40 maximum, the message "MEMORY OVERFLOW" will
appear.
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
To CHANNEL SUMMARY
To operate
è
π†√® To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the MENU button when finished
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Channel Guard Message
When a viewer attempts to watch a guarded channel, the following message appears:
To watch a channel that you have locked, enter the
THIS CHANNEL IS LOCKED BY
CHANNEL GUARD.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
Lock Code using the 10 key pad.
If the wrong code is entered, the message
“INVALID LOCK CODE!” will flash on the screen.
The channel cannot be accessed until the correct code
is entered.
NO. - - - -
Notes:
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.
• See also “Set Lock Code”, page 43.
V-Chip
Your TV is equipped with V-Chip technology which enables you to block channels or content
that you feel to be inappropriate for children, based on US rating guidelines. V-Chip has no
effect on video signals from DVD discs or Camcorder connection.
Note: Some programs, and movies are broadcast without a ratings signal. Even if you set
up V-CHIP ratings limits, these programs will not be blocked. See page 39 for information on
how to block unrated programs
You can customize the V-Chip settings of your television to match your personal tastes. The
V-Chip menu below is the starting point for your V-Chip settings
You can use US V-Chip settings and movie ratings. You may use any or all of the settings (US
V-Chip and Movie ratings). Descriptions for setting each of the three V-Chip formats appear in
the next five pages along with descriptions of the rating categories.
To access the rating categories:
Press the MENU button
V-CHIP
V-CHIP
OFF
π†
è
To V-CHIP
To operate (Lock icon
SET US TV RATINGS
SET MOVIE RATINGS
will appear)
Press ZERO to access the V-Chip menu
UNRATED
VIEW
è
To turn V-Chip ON or OFF (V-Chip must be
turned ON for rating settings to operate)
π†
To move to SET US TV RATINGS and
SET MOVIE RATINGS. (see following pages
for descriptions of each item)
MENU
SELECT OPERATE
EXIT
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Unrated Programs
Unrated programming refers to any programming which does not contain a rating signal.
Programming on television stations which do not broadcast rating signals will be placed in the
“Unrated Programming” category.
Examples of Unrated programs:
• Emergency Bulletins
• News
• Public Service Announcements
• Sports
• Locally Originated Programming
• Political Programs
• Religious Programs
• Weather
• Some Commercials
Note:
• TV programs or movies that do not have rating signals will be blocked if the unrated category
is set to BLOCK.
Directions to Block Unrated Programs
You can block programs that are not rated.
Press the MENU button
V-CHIP
OFF
V-CHIP
π†
To V-CHIP
SET US TV RATINGS
SET MOVIE RATINGS
è
To operate (The lock icon
appears)
Press ZERO to access V-Chip setup options
UNRATED
VIEW
π†
To UNRATED
è
To VIEW or BLOCK
MENU
SELECT OPERATE
EXIT
Press MENU when done
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
US V-Chip Ratings
U.S. PARENTAL RATING SYSTEMS
Programs with the following ratings are appropriate for children.
❒ TV Y is Appropriate for All Children
Programs are created for very young viewers and should be suitable for all ages, including
children ages 2 - 6.
❒ TV Y7 is for Older Children
Most parents would find such programs suitable for children 7 and above. These programs
may contain some mild fantasy violence or comedic violence, which children should be able
to discern from reality.
Programs with the following ratings are designed for the entire audience.
❒ TV G stands for General Audience
Most parents would find these programs suitable for all age groups. They contain little or no
violence, no strong language, and little or no sexual dialog or situations.
❒ TV PG Parental Guidance Suggested
May contain some, but not much, strong language, limited violence, and some suggestive
sexual dialog or situations. It is recommended that parents watch these programs first, or
with their children.
❒ TV 14 Parents Strongly Cautioned
Programs contain some material that may be unsuitable for children under the age of 14
including possible intense violence, sexual situations, strong coarse language, or intensely
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.
❒ TV MA Mature Audiences Only
These programs are specifically for adults and may be unsuitable for anyone under 17
years of age. TV MA programs may have extensive V, S, L, or D.
Viewing Guidelines
In addition to the ratings categories explained above, information on specific kinds of content
are also supplied with the V-Chip rating. These types of content may also be blocked. The
content types are:
• V/FV is for VIOLENCE/FANTASY VIOLENCE
• S stands for SEXUAL CONTENT
• L stands for strong LANGUAGE
• D stands for suggestive DIALOG
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Setting US V-Chip Ratings
Press the MENU button
V-CHIP
V-CHIP
OFF
π†
è
To V-CHIP
To operate (lock icon
SET US TV RATINGS
SET MOVIE RATINGS
appears)
Press ZERO to access the V-Chip menu
UNRATED
VIEW
è
π†
è
To turn V-Chip ON or OFF
To move to SET US TV RATINGS
To operate
MENU
SELECT OPERATE
EXIT
Directions to set US V-Chip Ratings
Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and
press the π† or √® to move the cursor to the correct location. Press OK to turn the locking
feature on or off. An item is locked if the
icon appears instead of a “—”.
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that
column and add a lock icon. Once you’ve put a lock on the top row, everything in that column
is automatically locked.
SET US TV RATINGS
π†√® To the TV 14 Column
TV
TV
TV
PG
TV
G
TV
Y7
TV
Y
Press the OK button to lock
MA 14
Press the MENU button when finished
V/FV
S
L
Note:
D
• If you want to change the setup, move the cursor to
the top column and change the lock icon to “—” by
pressing OK again. You may then select individual
categories to block.
OK
MENU
EXIT
SELECT
OPERATE
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Movies Ratings
❒ NR – Not Rated
This is a film which has no rating. In many cases these films were imported from countries
which do not use the MPAA ratings system. Other NR films may be from amateur producers
who didn’t intend to have their film widely released.
NR (Not Rated) Programming may contain all types of programming including children’s
programming, foreign programs, or adult material.
❒ G – General Audience
In the opinion of the review board, these films contain nothing in the way of sexual content,
violence, or language that would be unsuitable for audiences of any age.
❒ PG – Parental Guidance
Parental Guidance means the movie may contain some contents such as mild violence,
some brief nudity, and strong language. The contents are not deemed intense.
❒ PG-13 – Parents Strongly Cautioned
Parents with children under 13 are cautioned that the content of movies with this rating may
include more explicit sexual, language, and violence content than movies rated PG.
❒ R – Restricted
These films contain material that is explicit in nature and is not recommended for
unsupervised children under the age of 17.
❒ NC-17 – No One Under 17
These movies contain content which most parents would feel is too adult for their children
to view. Content can consist of strong language, nudity, violence, and suggestive or explicit
subject matter.
❒ X – No One under 18
Inappropriate material for anyone under 18.
Directions to set Movie (MPAA) Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET MOVIE RATINGS
To enter movies menu
For example:
To block viewing of X and NC-17 rated from shows:
SET MOVIE RATINGS
π†√® To the X Column
Press the OK button to lock
π†√® To the NC-17 Column
Press the OK button to lock
Press the MENU button to finish
N
P
C17
R
G13
PG
G
X
NR
OK
MENU
EXIT
SELECT
OPERATE
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Set Lock Code
Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes
preset with a lock code of “0000”. You may change the code to any four-digit number you wish.
To change the lock code, follow the steps below.
Press the MENU button
SET LOCK CODE
π†
To SET LOCK CODE
To operate (lock icon
LOCK CODE
0000
è
appears)
Press ZERO to access the lock code
The first digit will be highlighted
OK
PRESS
TO FINISH
MENU
SELECT OPERATE
EXIT
è
π†
To select the number
To move to the next digit
Continue to follow these directions for all four numbers
Press the OK button to finish (your lock code is now set)
Press the Menu button when finished
When a viewer attempts to watch a blocked channel, this message appears:
THIS PROGRAMMING EXCEEDS
YOUR RATING LIMITS.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. - - - -
The channel will remain blocked until the correct lock code is entered (see above for
information on setting your lock code).
Notes:
• After a power interruption you must reset the lock code.
• Write your lock code number down and keep it hidden from potential viewers.
• If you forget the lock code, a new code may be set using the steps listed above.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Adjusting CRT Color Convergence
This TV has three color projection tubes: one for red, green, and blue. When mixed together
in the proper portions, the output of these three color tubes can produce any color. To produce
these colors, however, the beams must be precisely aligned over each other so that the colors
can be mixed. The produce of aligning these picture beams is called “convergence”.
Attention:
• Please have your TV on for at least 20 minutes before using this feature.
• This adjustment will be needed only when the colors of the characters/lines are separated
and lack in distinction. If not, please don’t perform the adjustment.
Colors may become separated after the TV has
CONVERGENCE
been moved, or over a long period of time if regularly
subjected to low levels of vibrations. If the colors become
separated, please perform the adjustments below
AUTO
MANUAL
again. In the beginning, please be sure to perform
RESET
AUTO convergence adjustment.
MENU
SELECT OPERATE
EXIT
Auto
Press the MENU button
π† To CONVERGENCE
è
π†
To Enter
To select “AUTO” (The convergence adjustment
will start. It will take about 50 seconds).
SUPER FOCUS
When the adjustment is finished, it will return to
what you were watching.
Note:
• You can reset the adjustment if you do not like the results. See the next page.
• If you want to adjust it more, you can perform the manual color convergence adjustment.
See the next page.
• You can also access this feature by pressing the SUPER FOCUS button on the front panel of
your TV.
INPUT- 4
S-VIDEO VIDEO
AUDIO
MONO
OVER
L
/
R
MENU
CHANNEL
VOLUME
SUPER
FOCUS
–
+
–
+
OPERATE
OPEN
SUPER
FOCUS
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Adjusting CRT Color Convergence (continued...)
Manual
Press the MENU button
π† To CONVERGENCE
è To Enter
π† To choose MANUAL
è To Enter
If all the lines are white, no convergence adjustment is
necessary. If not, you need to perform the manual color
convergence below.
2
5
8
Select the location you want to adjust by using the
number buttons on the remote control.
You can select any of the 81 points.
4
6
Press the SELECT button to change the color of the
box
to the color of the cross you wish to adjust (red or blue).
π†√® Adjust the position of the cross.
Adjust the three color crosses until they overlap and appear as a single white
cross.
Press the OK button
Notes:
• When you adjust the convergence, make sure you start with the center position (position 5),
and work your way around radially for best results.
• When you make the adjustment in the center (position 5), you are making the adjustment for
the whole screen. In other positions, you are making the adjustment only in that area.
• You can reset the adjustment if you do not like the results. See below.
• If you perform AUTO convergence after performing MANUAL convergence, your manual
convergence you performed will be cancelled.
Reset
RESET resets all convergence adjustments to the factory default settings.
Press the MENU button
π† To CONVERGENCE
è
To Enter
π† To RESET
è
To enter
When the adjustment is reset, it will return to what you were watching.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Auto Demo
This function lets you preview the many different viewing modes of your TV. It will cycle through
“Multi Screen Demo”, “Picture in Picture Demo”, all of the different “Aspect” ratios and all of the
different “Video Status” modes.
Press the MENU button
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
π† To AUTO DEMO
CHANNEL SUMMARY
V-CHIP
è
To turn AUTO DEMO ON or OFF
SET LOCK CODE
CONVERGENCE
AUTO DEMO
Note:
OFF
(4/5)
• To stop auto demo, press the MENU button, and select
auto demo by pressing the π† buttons, and turn it off
by pressing the è buttons. Press the MENU button to
finish.
NEXT PAGE
MENU
SELECT OPERATE
EXIT
Language
The language function is described on page 25 as the interactive plug-in menu. If you need to
choose the language again, follow the steps below.
Press the Menu button
INITIAL SETUP
PREVIOUS
π†
To LANGUAGE
LANGUAGE
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
è
To choose a language: ENG. (English), FRAN.
(French) or ESP. (Spanish)
OFF
ON
Press the MENU button when finished
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Closed Caption
Many broadcasts now include an onscreen display of dialog called closed captions. Some
broadcasts may also include displays of additional information in text form. Your television can
access and display this information using the closed caption feature. To activate the closed
caption feature, follow the steps below. There are three methods. When you are watching
analog channels, you can perform Analog Setting of closed caption. When you are watching
digital channels, you can perform Digital Auto Setting or Digital Manual Setting.
Analog Setting
Press the MENU button
CLOSED CAPTION
π†
è
π†
è
π†
è
To CLOSED CAPTION
To enter
To MODE
To select CAPTION or TEXT in MODE
To CAPTION or TEXT
To select a caption (CC1 to CC4) or text
channel (T1 to T4)
MODE
TEXT
CC1
T1
CAPTION
TEXT
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
Press the OK button to save
Press the MENU button when finished
Digital Auto Setting
Press the MENU button
Digital Closed Caption
Preview
π†
è
π†
è
To CLOSED CAPTION
To enter
To Type
Closed Caption Sample
Type
AUTO
1
Service
Appearance
To select Auto, Advanced or Basic
Auto: Shows closed caption a priority for
digital channels over analog channels. It is
set automatically.
Cancel
Set
BACK
MENU
Select
Operate
Back
Exit
Advanced: Shows only the digital cloased
caption.
Basic: Shows only the analog closed
caption.
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Appearance Mode
Auto
π†
è
π†
è
è
π†
To Service
Font
To select 1, 2, 3, 4, 5 or 6
To Appearance
To enter
To select Auto
To Set
Colors
Opacities
Cancel
Set
BACK
MENU
Select
Operate
Back
Exit
Press the OK button to save
The font/type and color are set automatically.
Press the MENU button when finished
Note:
• If you want to cancel the settings, select cancel.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Digital Manual Setting
Press the MENU button
Digital Closed Caption
Preview
>
Appearance
π†
To CLOSED CAPTION
Closed Caption Sample
è
π†
è
π†
è
π†
è
è
π†
è
π†
è
To enter
To Type
Appearance Mode
Manual
Font
Colors
Opacities
To select Auto, Advanced or Basic
To Service
To select 1, 2, 3, 4, 5 or 6
To Appearance
To enter
To select Manual
To Font
To enter
To select Font Size or Font Style
To select the setting you like
Cancel
Set
BACK
MENU
Select
Operate
Back
Exit
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Font Size
Standard
Auto
Appearance Mo
Font
Font Style
Colors
Font Size: Auto, Standard, Large or Small
Cancel
Set
Opacities
Cancel
Font Style: Auto, Serif Mono, Serif, Sanserif mono,
Sanserif, Casual, Cursive or Small Capital
π†
Set
BACK
MENU
Select
Operate
Back
Exit
To Set
Press the OK button to save
π†
è
π†
è
To Colors
To enter
To select Text, Edge or Background
To select the setting you like
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Text
Appearance Mo
White
White
Black
Edge
Auto, White, Black, Red, Green, Blue,
Yellow, Magenta or Cyan
Font
Background
Cancel
Colors
Opacities
Set
π†
To Set
Cancel
Set
BACK
MENU
Press the OK button to save
Select
Operate
Back
Exit
π†
è
π†
è
π†
To Opacities
To enter
To select Text/Edge or Background
To select Auto, Transparent, Translucent, Solid or Flashing
To Set
Press the OK button to save
Press the MENU button when finished
Notes:
• Closed caption subtitles are usually found on closed caption channel CC1. Some programs
may include additional text information which is usually found on text channel T1. The other
channels are available for future use.
• Closed captioning may not work correctly if the signal being received is weak or if you are
playing a video tape.
• Most broadcasts containing closed captioning will display a notice at the start of the program.
• To select the mode, press the C.C. button. See page 66.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Auto Shut Off
This function automatically shuts off your TV when there is no signal from the channel the TV is
on.
INITIAL SETUP
Press the MENU button
PREVIOUS
π†
è
To AUTO SHUT OFF
To turn ON or OFF
LANGUAGE
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
Press the MENU button when finished
• If the channel that you have on does not receive a
signal for more than one minute, the blinking text
“NOT RECEIVING A SIGNAL AUTO SHUT OFF
in 9 MIN.” appears on the screen, and starts the
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
countdown. If no signal is being received within 10 minutes, the TV shuts itself off.
• When i.LINK is displayed, Auto Shut Off will not work.
XDS ID
XDS ID Display provides a channel’s call letters, the network’s name, and even a program
name. The XDS ID information is provided by the broadcaster.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To XDS ID
To turn ON or OFF
LANGUAGE
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
Press the MENU button when finished
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
Noise Muting
This feature inserts a blank gray screen over channels which are not broadcasting or are too
weak to be received clearly.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To NOISE MUTING
To turn noise muting ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
Press the MENU button when finished
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
LOW
NEXT PAGE
(2/5)
Notes:
MENU
SELECT OPERATE
EXIT
• Noise muting will not work during auto tuner setup or
when you operate channel summary.
• Noise muting will not work when the digital TV or i.LINK is displayed.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Front Panel Lock
This allows you to lock the keys on the front of the TV, so that a child may not accidentally
change your viewing preferences.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To FRONT PANEL LOCK
To turn ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
Press the MENU button when finished
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
LOW
You can turn off this feature in the following ways:
NEXT PAGE
(2/5)
MENU
SELECT OPERATE
EXIT
• Unplug the power cord, and plug it back in. Do this if
your batteries die, or you lose your remote control.
• Use the remote control.
• Press the MENU button on the front of the TV for more than 3 seconds. In this case, the OSD
for FRONT PANEL LOCK will appear.
Note:
• To turn ON/OFF the TV, press the power button for more than 3 seconds. This feature will
remain ON.
V1 Smart Input
This feature is used if you have connected an AV Receiver to your television. By turning this
feature on, your television can automatically detect the signal source from your components
that are connected to your AV Receiver.
Press the MENU button
INITIAL SETUP
π†
è
To V1 SMART INPUT
To turn ON or OFF
PREVIOUS
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
Press the MENU button when finished
Notes:
LOW
• If you do not have an AV Receiver connected to your
television, turn this feature OFF. By doing so, you can
take advantage of using AV CompuLink components
with your television.
NEXT PAGE
(2/5)
MENU
SELECT OPERATE
EXIT
• Some AV Receivers may not work with this function.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Video Input Label
This function is used to label video input connections for the onscreen displays.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
π†
è
To VIDEO INPUT LABEL
To enter
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
To select the desired video input
LOW
To select the desired preset input label (see
chart below)
NEXT PAGE
(2/5)
MENU
SELECT OPERATE
EXIT
Press the OK button to save
VIDEO INPUT LABEL
Press the MENU button when finished
VCR
DVD
VIDEO-1
VIDEO-2
VIDEO-3
VIDEO-4
DIGITAL-IN
SAT
GAME
STB
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
Preset
Labels
Select when...
You have a VCR connected to the video input
You have a DVD connected to the video input
VCR
DVD
DVHS
STB
You have a Digital VCR connected to the video input
You have a Set-top Box connected to the video input
You have a Satellite Receiver connected to the video input
You have an Amplifier connected to the video input
You have a Video Game connected to the video input
You have a Video Camera connected to the video input
You have a Video Disc player connected to the video input
SAT
AMP
GAME
CAM
DISC
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Position Adjustment
Position adjustment allows you to adjust the position of the picture on the screen vertically
when the aspect is set to panorama, cinema or full.
Press the MENU button
π†
è
To POSITION ADJUSTMENT
To enter
π†√® To adjust the position
Press the MENU button to finish
OK
MENU
RESET
EXIT
OPERATE
Notes:
• To reset the adjustment to the center, press the OK button.
• When the arrow disappears, while you are adjusting the position, the position is at its
maximum limit.
• If you select regular size with aspect or Multi Screen, position adjustment option is not seen.
• When you change the screen size, perform the position adjustment again.
• Position adjustment allows you to adjust the screen position vertically and horizontally when
the aspect is set HD panorama or cinema zoom for 1080i and 720p signals.
Power Indicator
Power indicator allows you to adjust the brightness of the power indicator
Press the MENU button
INITIAL SETUP
PREVIOUS
π† To POWER INDICATOR
NOISE MUTING
ON
OFF
ON
è
To adjust POWER INDICATOR LOW, HIGH
or OFF
FRONT PANEL LOCK
V1 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
Note:
• If you set a timer on the TV, the power indicator will
light even if the TV is on stand by.
LOW
NEXT PAGE
(2/5)
MENU
SELECT OPERATE
EXIT
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Digital-In
The DIGITAL-IN option can only be displayed in the INITIAL SETUP menu when an HDMI480p
picture signal is being input to the DIGITAL-IN terminal. This option adjusts the position when
an HDMI or DVI 480p picture signal is being displayed on the screen. There are two types of
HDMI 480p picture signals: 640x480 and 720x480. If the displayed picture is slightly shifted,
the position can be adjusted by selecting either SIZE1 or SIZE2.
Press the MENU button
INITIAL SETUP
PREVIOUS
SIZE1
DIGITAL
ON
DIGITAL-IN
π† To DIGITAL-IN
DIGITAL-IN AUDIO
CENTER CH INPUT
VIDEO-1 MONITOR OUT
è To select SIZE1 or SIZE2
Press the MENU button to finish
OFF
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
Digital-In Audio
This feature is used if you have a DTV or HDMI compatible component connected to your TV.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
To DIGITAL-IN AUDIO
SIZE1
DIGITAL
ON
DIGITAL-IN
DIGITAL-IN AUDIO
CENTER CH INPUT
VIDEO-1 MONITOR OUT
è
To select ANALOG or DIGITAL
Press the Menu button when finished
OFF
Notes:
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
• If your DTV or HDMI component is capable of digital
audio and video, choose DIGITAL. If your DTV or
HDMI component is capable of analog audio and
digital video, choose ANALOG.
• Refer to your DTV or HDMI component’s instruction manual for more information.
• When you select DIGITAL, select PCM on Digital Sound in the Digital Setup menu. See page
72.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Center CH Input
When you are using a surround system, you can substitute the speaker of this television for
the center speaker of your surround system. Set CENTER CH INPUT to ON when you use the
speaker as the center speaker of your surround system. The volume differs when the TV is
being utilized as the Center Channel Input versus when it is not.
Press the MENU button
INITIAL SETUP
PREVIOUS
SIZE1
DIGITAL
ON
DIGITAL-IN
π†
è
To CENTER CH INPUT
To adjust CENTER CH INPUT to ON
or OFF
DIGITAL-IN AUDIO
CENTER CH INPUT
VIDEO-1 MONITOR OUT
OFF
Press the MENU button when finished
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
Note:
• In order to use the CENTER CHANNEL SPEAKER feature, you need a video signal present
as well as sound. Because of that we recommend using this feature for Home Theater setup
only. If there is no video signal present, the TV will be muted.
• There are two different volume adjustment levels, one for regular TV and one for TV used as
a CENTER CHANNEL. Please remember that when switching CENTER CHANNEL mode ON
and OFF in TV menu.
Video-1 Monitor Out
This function allows you to set whether the signal, which comes from VIDEO-1 input terminal,
should be output from MONITOR OUT terminal. If you select it from MONITOR OUT, set it to
"ON".
Press the MENU button
INITIAL SETUP
PREVIOUS
π† To VIDEO-1 MONITOR OUT
SIZE1
DIGITAL
ON
DIGITAL-IN
DIGITAL-IN AUDIO
CENTER CH INPUT
VIDEO-1 MONITOR OUT
è To select ON or OFF
Press the MENU button to finish
OFF
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjust
Picture Settings
These settings allow you to change and adjust the way the picture appears on your television.
TINT
Tint allows you to adjust the levels of red and green in your TV picture.
COLOR
The color function lets you make all the colors in the TV picture appear either more vivid or
subtle.
PICTURE
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker
or brighter picture overall.
BRIGHT
You can adjust the overall brightness of the TV picture with the Bright control.
DETAIL
The Detail feature adjusts the level of fine detail displayed in the picture.
Adjust the Picture Settings
Press the MENU button
PICTURE ADJUST
π†
To TINT, COLOR, PICTURE, BRIGHT or
DETAIL
To enter
PREVIOUS
TINT
STANDARD
00
00
00
00
00
COLOR
PICTURE
BRIGHT
DETAIL
√ ®
+02
TINT
COLOR TEMPERATURE
NEXT PAGE
HIGH
(1/2)
EXIT
√ ®
π†
To adjust the setting
To move to the next setting
MENU
SELECT OPERATE
Press the MENU button when finished
Color Temperature
You can decide how strong or dull the colors appear on the TV screen.
Press the MENU button
PICTURE ADJUST
PREVIOUS
π†
è
To COLOR TEMPERATURE
To enter
STANDARD
TINT
00
00
00
00
00
COLOR
PICTURE
BRIGHT
DETAIL
COLOR TEMPERATURE LOW HIGH
è
To set LOW or HIGH
COLOR TEMPERATURE
NEXT PAGE
HIGH
Press the MENU button when finished
(1/2)
EXIT
MENU
SELECT OPERATE
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjust
Digital Noise Clear
With digital noise clear, this helps take our static or noise from a channel that may not be
coming in clearly.
Press the MENU button
DIG. NOISE CLEAR
π†
è
π†
To DIG. NOISE CLEAR
To enter
To select the mode LOW, HIGH or OFF
OFF
LOW
HIGH
Press the MENU button when finished
(VSM) Velocity Scan Modulation
Velocity scan modulation circuitry varies the electron beam’s horizontal scanning speed to help
accentuate the differences in picture brightness to sharpen the edges of images.
Press the MENU button
PICTURE ADJUST
PREVIOUS
DIG. NOISE CLEAR
VSM
STANDARD
π†
è
To VSM
To enter
OFF
ON
VSM
ON OFF
RESET
è
To turn VSM ON or OFF
NEXT PAGE
(2/2)
MENU
SELECT OPERATE
EXIT
Reset
Reset resets all picture adjustments (tint, color, picture, bright, detail, color temperature, dig.
noise clear and VSM) at once to the default settings.
Press the MENU button
PICTURE ADJUST
π†
è
To RESET
To enter
PREVIOUS
DIG. NOISE CLEAR
VSM
STANDARD
OFF
ON
The onscreen menu disappears for a
moment, and then the settings are reset
to the default setting for all the picture
adjustments.
RESET
NEXT PAGE
(2/2)
MENU
SELECT OPERATE
EXIT
Press the MENU button when finished
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Adjust
Sound Settings
These settings allow you to change and adjust the sound on your television.
BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with
the bass adjustment.
TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.
BALANCE – Adjust the level of sound between the TV’s left and right speakers with the
balance setting.
Adjust the Sound Settings
Press the MENU button
SOUND ADJUST
PREVIOUS
π†
√ ®
π†
To BASS, TREBLE or BALANCE
To adjust the setting
To move to the next setting
BASS
00
00
00
TREBLE
BALANCE
Press the MENU button when finished
RESET
NEXT PAGE
Note:
MENU
SELECT OPERATE
EXIT
• You can reset the sound adjustments
(BASS, TREBLE and BALANCE) you set at once as the default setting when you select
reset. See page 56.
• You can adjust BALANCE only when A.H.S. is off. See page 63.
Reset
Reset resets all Sound Adjustments (Bass, Treble and Balance) at once to the default settings.
See page 56 on how to use reset.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock/Timers
Set Clock
The set clock function is described on page 26 as the interactive plug-in menu. You can choose
to set the clock automatically or manually. If you need to set the clock again, follow the steps
below.
Press the MENU button
π†
è
To SET CLOCK
To enter
When you set the clock automatically, choose AUTO by pressing the
√
or
®
arrows.
π†
è
To TIME ZONE
To select your time zone
SET CLOCK
ATLANTIC
CENTRAL
EASTERN
HAWAII
MOUNTAIN
ALASKA
PACIFIC
MODE
AUTO
--: ----
π†
è
To D.S.T. (daylight savings time)
To turn D.S.T. ON or OFF
TIME
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/04
ON
Press OK to finish
OK
PRESS TO FINISH
SELECT OPERATE
Press the MENU button when finished
MENU
EXIT
When you set the clock manually, choose MANUAL by
pressing the or arrows.
√
®
π†
è
π†
è
π†
è
To move to the hours
To set the hours
To move to minutes
To set the minutes
To TIME ZONE
SET CLOCK
MODE
MANUAL
--: ----
TIME
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/04
ON
To select your time zone:
(Atlantic, Eastern, Central, Mountain, Pacific,
Alaska or Hawaii)
OK
PRESS TO START CLOCK
π†
è
π†
è
π†
è
π†
è
To DATE/YEAR
To set the month
To day
To set the day
To year
MENU
SELECT OPERATE
EXIT
To set the year
To D.S.T. (daylight savings time)
To turn D.S.T. ON or OFF
Press OK to start clock
THANK YOU !!
Press the MENU button when finished
Notes:
• D.S.T. can be used when it is set to ON in the SET CLOCK menu.
• Only when the MODE set to AUTO, the Daylight Savings Time feature automatically adjusts
your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on
the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in
October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock/Timers
On/Off Timer
The on/off timer lets you program your television to turn itself on or off. You can use it as an
alarm to wake up, to help you remember important programs, or as a decoy when you’re not
home.
Press the MENU button
ON/OFF TIMER
7:00 PM
10:00 PM
03
ON TIME
π†
è
è
To ON/OFF TIMER
OFF TIME
CHANNEL
ON VOLUME
MODE
To enter (begins with ON TIME)
CURRENT
EVERYDAY
NO
To set the hour (AM/PM) you want the TV to
turn on
ON/OFF TIMER
†
è
†
To move to minutes
To set the minutes
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
To accept ON TIME and move to OFF TIME (the time the TV will turn off). Set the
OFF TIME the same way as ON TIME
†
è
†
To accept OFF TIME and move to CHANNEL
To select channel
To ON VOLUME
è
†
To set the volume level
To move to MODE
è
Choose ONCE or EVERYDAY
†
To ON/OFF TIMER
è
Choose YES to accept the timer setting, choose NO if you don’t wish to accept
Press the OK button to finish
Press the MENU button to exit the menu
Notes:
• The on/off time cannot be set to locked or guarded channels.
• In order for the on/off timer to work, the clock must be set.
• After a power interruption, the timer settings must be reset.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Multi Screen Function
Your television has two kinds of screen: TWIN (2 channels) and INDEX (12 channels).
Note: After you press any multiscreen buttons, if you press the menu button, only the picture
adjust screen will appear.
Twin
Activate the split-screen option by pressing TWIN on
07
V-1
the remote control. The channel (or input) you were
watching before pressing TWIN will appear on the left,
the new channel will appear on the right. The sound
will continue to come from the main screen channel
(or input). To turn split-screen off and return to
normal television viewing, press TWIN again or press
the BACK button.
MAIN SCREEN
PICTURE
SPLIT SCREEN
PICTURE
Notes:
• If the signal that you are watching is coming from the HDMI input, you cannot enter the
TWIN mode.
• Main Screen and Split Screen will not display the same channel or input at the same time.
• You can enter the TWIN mode when the screen is in NORMAL or INDEX mode.
• Split-screen functions will not work with locked channels or channels blocked by V-Chip
ratings limits. A gray screen will display instead.
• The aspect of MAIN CHANNEL PICTURE becomes 16:9 when you input the picture of
480p, 720p and 1080i from the component terminal.
• After you press the SELECT button, and select SPLIT SCREEN when you press the
OK button, select normal screen. If you don’t operate, the MAIN CHANNEL SCREEN will
be automatically selected about 8 seconds later.
• Aspect does not work in Twin mode.
• When the cable card is inserted into the TV, the combination of analog broadcasting and
digital broadcasting will not appear in the TWIN mode.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Index
This allows you to quickly look at up to 12 channels at a time so that you can decide which one
to watch.
1
5
9
2
3
4
6
7
8
10
11
12
Notes:
• Only RF input signal will be displayed.
• You can watch the channel added in channel summary. See page 36.
Freeze
Pressing the FREEZE button causes the screen to change to the split-screen display with the still
picture displayed on the right. In order to return to the normal display, press the FREEZE button
once again.
Note: When the screen is in freeze mode, if you do not operate it within 15 minutes, this
function will cancel out.
Swap
You can exchange the channel (or input) displayed in the split screen window for the main
screen image by pressing the SWAP button.
Note: It will only work in TWIN mode.
Select
With SELECT, you can select the picture (channel) while viewing TWIN screen. When you
press SELECT button, the channel number on the top will be highlighted. Each press of SELECT
will shift the channel.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Power
Turns the TV on or off.
Press the POWER button
Number Buttons - 10Key Pad
Use the number buttons on the remote control to move directly to a specific channel. For
example, to move to channel 12:
0 (Zero)
1 (One)
2 (Two)
Tune
Lets you decide the input channel and select it. After you press the number buttons on the
remote, press the TUNE button. For example, to move to channel 12:
1 (One)
2 (Two)
Press the TUNE button
Input
Selects the signal input source for the television: Input-1, 2, 3, 4 DIGIATL-IN or i.LINK for
video devices like VCRs, DVD players or camcorders.
Press the INPUT button
By every press of the INPUT button, you can change the input mode.
Notes:
• When you return to TV mode, press the RETURN+ button or direct 10 key pad.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the front of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has INPUT, VIDEO STATUS and ASPECT menus. Choose
INPUT by pressing MENU
†
on the front panel and choose a mode by using the CHANNEL+/-
buttons ( OPERATE ).
√
®
• i.LINK can be selected only when you have an i.LINK device connected.
Channel +/–
Use these buttons to move up or down all the available channels your TV is able to receive.
Volume +/–
Use these buttons to raise or lower the TV’s volume level.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Return +/TV
The RETURN+/TV button has three functions:
Return - Returns to the channel viewed just before the channel currently onscreen.
Return+ - Lets you program a specific channel to return to while scanning through the
channels using the CH+ and CH– buttons.
TV - Returns to the TV mode.
Press the RETURN+/TV and hold for three seconds
RETURN CHANNEL
PROGRAMMED!
The channel currently active has been programmed as your return+ channel. Now scan
through the channels using the CHANNEL+/– buttons.
Press the RETURN+/TV
You will return to your programmed channel.
• To cancel your return+ channel, press and hold the RETURN+ button for three seconds. The
message “RETURN CHANNEL CANCELLED!” will appear.
• Return+ works only with the Channel+/– buttons. Pressing any number key will cancel
return+.
Sound
Note : SMART SOUND (AV-56P785 ONLY)
By pressing the SOUND button, you can change the A.H.S. (Advanced Hyper Surround) mode,
BBE, and SMART SOUND on or off.
A.H.S. - Adds a more spacious surround sound. Music gives basic effect and movie for more
effect.
BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility
and musical realism.
SMART SOUND - Decreases high sound levels, giving a regulated sound level.
SOUND EFFECT
Press the SOUND button
π†
è
To select A.H.S., BBE or SMART SOUND
To choose the setting
A.H.S.
MOVIE MUSIC OFF
ON OFF
BBE
SMART SOUND
ON OFF
MENU
Press the MENU when finished
SELECT OPERATE
EXIT
Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under
USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered trademarks of
BBE Sound, Inc.
Note: Smart Sound may become an unnatural effect, depending on the signal source.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Video Status
The VIDEO STATUS button gives you a choice of four TV picture display settings, including a
display of your own preferences.
Standard - Resets the picture display to the factory settings.
VIDEO STATUS
Dynamic - Gives a vivid picture with better contrast when viewing in
STANDARD
a brightly lit room.
DYNAMIC
Theater - Gives a rich, film-like look to video when viewing in a
THEATER
dimly lit room.
GAME
Game - Used for when you are playing video games connected to
your TV.
Press the VIDEO STATUS button
By every press of the VIDEO STATUS button, you change the mode.
Note:
• You can also change the mode by pressing the π† buttons.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the back of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has INPUT, VIDEO STATUS and ASPECT menus. Choose
VIDEO STATUS by pressing MENU
†
®
on the back panel and choose a mode by using the
).
CHANNEL +/- buttons (
√
OPERATE
Natural Cinema
Natural cinema corrects the problem of blurred edges which may occur when viewing a program
originally shot on film (such as motion pictures) or animation. If you notice blurring at the edges
of these programs, press NATURAL CINEMA and set it to AUTO. Natural Cinema helps correct
conversion errors that occur when film, which is shot at 24 frames-per-second, is broadcast at the
television rate of 30 frames-per-second.
Press the NATURAL CINEMA button
NATURAL CINEMA
AUTO
Notes: The natural cinema mode is automatically set to “AUTO” in the
ON
following cases:
OFF
• Turning on or off
• Changing the channel or input mode
• Using multi-screen functions
TheaterPro D6500K
The TheaterPro D6500K color temperature technology function makes sure that the video you
watch is set to the standard color temperature, so that what you see is as true to what the film
to video editors intended it to be.
Press the THEATERPRO button
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Sleep Timer
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals
of 15 minutes, for a total time of up to 180 minutes.
Press the SLEEP button
0 15 30 45 60 75 90 105 120 135 150 165 180
Sleep Timer Message
20 seconds before the automatic shutoff, this message will appear:
GOOD NIGHT!!
PUSH SLEEP TIMER BUTTON
TO EXTEND
You then have 20 seconds to press the SLEEP button to
delay the shut off for another 15 minutes.
ML/MTS
MTS technology allows several audio signals to be broadcast in analog at once, giving you a
choice in what you wish to hear with a TV program. In addition to mono or stereo sound, an
MTS broadcast may also include a second audio program (SAP).
Press the ML/MTS button
MTS
By every press of the ML/MTS button, you change
the mode
ON AIR
STEREO
ON AIR
SAP
MONO
Notes:
• When you are receiving a digital broadcast, if there are other languages, you can change the
language by pressing the ML/MTS button.
• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo
mode even if a certain broadcast is in mono sound only.
• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.
• MTS unavailable if your television’s Input source is in input 1, 2, 3 or 4 mode, as described
on page 62.
• ML/MTS will not work when you are using the Digital-In.
• You can also change the mode by pressing the π† buttons.
Muting
The MUTING button instantly turns the volume down completely when you press it. Press
MUTING and the volume level will instantly go to zero. To restore the volume to its previous
level, press MUTING again.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Display
The display screen shows the current status of timers, inputs and XDS ID.
Press the DISPLAY button
The screen to the right shows the following information:
05 KLVX PBS
• The current channel or AV input (Channel 05)
JAZZ FESTIVAL
• The current time (12:20 pm)
• Sleep timer status/minutes remaining (The Sleep Timer
is off)
• On/off timer status (Set to turn on everyday at 7:00 PM,
off at 10:00 PM)
NOW
12:20 PM
OFF
SLEEP TIMER
ON/OFF TIMER
EVERYDAY
7:00 PM
ON TIME
OFF TIME
10:00 PM
• Each Press of the DISPLAY button changes the display
mode:
Display
Time
Channel
Off
Display - Full screen shown above
Time - Shows the current time only
Channel - Shows the current channel
Off - Turns display off
Notes:
• You may also turn off the display at any step by pressing MENU.
• If the clock, sleep timer or on/off timer are not set, the display screen will show:
“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.
C.C. (Closed Caption)
Use the C.C. (Closed Caption) button to select the mode of closed caption.
Press the C.C. button
AV-56P785 ONLY
OFF
SMART CAPTION
ON
AV-56P775 and AV-48P775 ONLY
OFF
ON
• Smart Caption will appear when you press the MUTING button, only on channels where the
broadcast contains closed captioning. (AV-56P585 ONLY)
• When you select ON, it will be the mode selected in the Closed Caption Menu.
• See page 47 when you set the caption/text mode.
• You can also change the mode by pressing the π† buttons.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Favorite
The Favorite button allows you to select your favorite channels easily. First, you must register
the channels that you like. See how to register below.
Press the FAVORITE button
FAVORITE
The favorite channel list will appear.
PREVIOUS
π†
To select the channel you want to watch
101
102
D103
<
CBS
FOX
PBS2
>
Press the OK button
It will change to the channel you have selected.
D107
8
HBO
ABC
Register the favorite channel
NEXT
Press the channel number you want to register
The channel program will change.
Press the FAVORITE button for three seconds
The channel will be registered in the favorite channel list.
Notes:
• Both analog and digital channels can be registered. The digital channels have a "D" in front
of the channel number.
• The maximum number of channels you can register is 24.
• If you have registered the maximum number of channels, and try to register more channels,
the oldest channel you registered will be deleted.
• Sub channels can not be registered.
• The newest channel you registered will appear at the top of the list.
• Regarding digital channels, see pages 74 to 80.
Delete the favorite channel
Press the FAVORITE button
The favorite channel list will appear.
π†
è
To select the channel you want to delete
To enter
Press the OK button
The channel was deleted.
Press the FAVORITE button when finished
Note:
• Before pressing the FAVORITE button when you are finished, press the √® button again, and
you can return to the deleted channel.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Aspect
This feature will help you adjust the picture you are watching to give you the best possible
picture quality.
Aspect Ratios
PANORAMA - With this ratio a normal
4:3 aspect picture is stretched to fit the
dimensions of the 16:9 aspect screen.
REGULAR - The regular ratio is used
when you want to watch a 4:3 broadcast
or recorded program without modifying the
original picture to fit the dimensions of your
16:9 screen. The 4:3 picture will fill the
screen from top to bottom, while black bars
will appear to fill up the remaining space
along the picture’s sides. The 4:3 picture
will be centered within the boundaries of the
16:9 screen.
CINEMA - This ratio “zooms in” on the
center part of a 4:3 aspect picture, blowing
it up to fill the 16:9 screen.
CINEMA ZOOM - This ratio stretches
the High-Definition 16:9 aspect image to
eliminate the black surrounding bars.
FULL - This is the ratio to use when
watching 16:9 High-Definition broadcasts.
HD PANORAMA - This ratio stretches
the High-Definition 16:9 aspect image to
eliminate the black side bars.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Aspect Ratios (Continued)
Press the ASPECT button
• By pressing the ASPECT button, you can change the size.
When you change the aspect ratios, it is different from their broadcast or recorded program.
NTSC, 480i, 480p
HD (1080i, 720p)
ASPECT
HD PANORAMA
CINEMA ZOOM
FULL
ASPECT
PANORAMA
CINEMA
FULL
REGULAR
Notes:
• You can also choose the size by pressing the π† buttons.
• When you change the aspect ratio or signal, reset the picture position to center.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the front of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has INPUT, VIDEO STATUS and ASPECT menus. Choose
ASPECT by pressing MENU
†
on the front panel and choose a mode by using the CHANNEL
+/- buttons (
√
OPERATE
®
).
Menu
The MENU button allows you to access JVC’s onscreen menu system. Press MENU to activate
the onscreen menu system.
• See individual topics like “Sound Adjust” for specific information on using menus.
OK
This button confirms your selection when you are in one of the onscreen menus.
Back
This button allows you to go back in the menu to change a selection or correct a mistake.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
TV/CATV Slide Switch
Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to
operate the television’s built-in tuner. Move the switch to CATV to operate a cable box.
Note:
• See page 28 for information on programming your remote for cable box operation.
VCR/DVD Slide Switch
You can control a VCR or DVD player with the buttons on the lower part of the remote control.
Move the slide switch to VCR or DVD to operate.
Notes:
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 29.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 30.
VCR Buttons
You can use this remote control to operate the basic functions of your VCR. These functions
include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on and
power off.
Move the selector switch to VCR to operate.
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 29.
DVD Buttons
You can also use this remote control to operate the basic functions of your DVD player. These
functions include: play, rewind, fast-forward, stop, still/pause, previous/next, tray open/close,
power on and power off.
Move the selector switch to DVD to operate.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 30.
Light
All remote control buttons are illuminated, except for the TV/CATV slide switch, VCR/DVD slide
switch and Light button. Press the LIGHT button to turn the illumination on for 4 seconds.
Super Focus
This button is only located on the front panel of your TV. When you press the SUPER FOCUS
button on the front of the TV, you can access the auto convergence mode in the convergence
menu screen automatically. See page 44.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Setup
Digital Setup
Use this function when you are receiving a digital broadcast.
Press the MENU button
Digital Setup
Antenna Level
π†
To DIGITAL SETUP
To enter
Digital Sound
PCM
4:3
è
Aspect Ratio
The onscreen will appear
Cable Card Application
i.LINK Auto Play
Software Update
OFF
Notes:
• Software Update will only appear when the SD Card
is inserted.
BACK
MENU
Select
Operate
Back
Exit
• If you are watching an analog channel, you can still
access the digital setup menu at anytime, while you are doing this, the background screen
will turn blank. In this case, the tuner will switch to digital, since you are accessing the digital
setup menu.
Antenna Level
Confirms the present antenna level.
Antenna Level
Press the MENU button
75
π†
To DIGITAL SETUP
To enter
BACK
MENU
è
Back
Exit
π†
To Antenna Level
To enter
è
Note:
• If you are watching an analog channel or a signal from your i.Link device, antenna level will
not appear.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Setup
Digital Sound
You can select the optical digital sound output, either PCM or Dolby Digital when your TV is
connected to an amplifier that has Dolby Digital decoder. If you select Dolby Digital, you can
enjoy listening in 5.1ch sound when watching digital broadcasts.
Press the MENU button
π†
To DIGITAL SETUP
To enter
è
π†
To Digital Sound
è
To select PCM or DOLBY DIGITAL
Press the MENU button when finished
Notes:
• If your amplifier does not have Dolby Digital decoder, select PCM. If you don't select PCM, it
cannot output the sound from the speakers.
• For connecting an amplifier using the optical output, see page 20.
Manufactured under license from Dolby Laboratories. "Dolby", and the
double-D symbol are trademarks of Dolby Laboratories.
Aspect Ratio
You can select the aspect mode for ATSC from 4:3 or 16:9.
Press the MENU button
π†
è
π†
è
To DIGITAL SETUP
To enter
To Aspect Ratio
To select 4:3 or 16:9
Press the MENU button when finished
Notes:
• Set the mode to 4:3 or 16:9 before you record a program using the ATSC MONITOR OUT.
• Make sure the mode you choose is the same as the TV’s aspect ratio when the recorded
program is played back, so that you can obtain a good picture quality, free from any unatural
distortions.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Setup
Cable Card Application
Press the MENU button
π†
è
π†
è
To DIGITAL SETUP
To enter
To Cable Card Application
To enter
Press the OK button
The application will perform
i.LINK Auto Play
When playing a D-VHS tape, you can set it to the i.LINK input automatically, or manually.
Press the MENU button
π†
è
π†
To DIGITAL SETUP
To enter
To i.LINK Auto Play
è
To select ON or OFF
ON: Set to i.LINK input automatically
OFF: Select the input manually
Press the MENU button when finished
Software Update
At first, insert the SD(Multi-media) card into the memory card slot. This function will appear
only when you insert an SD Card.
Press the MENU button
π†
è
π†
è
π†
To DIGITAL SETUP
To enter
To Software Update
To enter
Checks the card if it needs an update or not
Press the MENU button when finished
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Digital CH D/A (Digital/Analog)
The D/A button changes the analog and digital channel. Each time you press the D/A button,
you can switch back and forth the analog and digital channels. Digital channels have a "D" in
front of the channel number.
Note:
• If the cable card is inserted into the TV, you cannot use the D/A button. You can select a
digital channel only.
Press the D/A button
To watch digital channels
For example, to move to channel D23:
Press 2 (Two)
Press 3 (Three)
Press the TUNE button
Sub Channel
The main channel sometimes has minor channels (Sub Channels). By using the SUB button,
you can select a sub channel easily.
For example, to move to sub channel 123-45:
Press 1 (One)
Press 2 (Two)
Press 3 (Three)
Press the SUB button
Press 4 (Four)
Press 5 (Five)
Press the TUNE button
Note:
• If there are more than 2 major channels, select the digital channel by using the π† buttons
and then press the OK button.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
i.LINK Menu
i.LINK has two menus - Controller and Device.
By connecting a D-VHS VCR with an i.LINK cable, you can set the timer easily.
Notes:
• The i.LINK/Timer function will only work when you are receiving digital programming only.
• As for the connection of a D-VHS VCR with the i.LINK cable, see page 24.
• When operating the i.LINK, don't insert or disconnect the i.LINK cable.
Controller
You can operate a D-VHS VCR connected with an i.LINK cable by using this controller.
Notes:
• If the i.LINK is not connected, the Controller OSD will not appear. The OSD of device on
page 76 will appear.
• Some controller operations may differ from your D-VHS VCR operations.
Press the i.LINK MENU button
i.LINK
Controller
D-VHS1
STOP
00:00:00
POWER
Device
√®π† To select the key you want to operate
Press the OK button
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Device
To operate, select a device.
i.LINK
Controller
Device
Renumber
Page 2/3
D-VHS1
JVC
HM-DH30000U
D-VHS2
JVC
HM-DH40000U
HD-MOVIE 1
GR-HD1
JVC
π†
To select your device connecting with i.LINK
Press the OK button
Notes:
• If you do not select the device, you cannot use the i.LINK timer functions.
• When one device is selected and you select controller, you will move to the Controller
onscreen.
• The devices listed on the device onscreen are only D-VHS and HD-MOVIE that have i.LINK,
which can be recognized on this television. However, you can not record programs to HD-
MOVIE.
• If you disconnect one device, it will be removed from the list. Then, select Renumber to
rearrange the list in the new order.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Timer
You can set the two timers: Record and view. The timer starts the recording or turns to the
channel you set for it automatically.
Reservation
Press the TIMER button
π†
To New Reservation
Press the OK button
New Reservation
Timer
Timer Mode
Rec
Channel
Date
35-1
V
New Reserva
Sep. 10 (wed)
5:00PM
Start Time
End Time
80-3 PBS1D
6:00PM
Sep. 11 (Wed
335-1 KDVR
Weekly/Daily
Weekly
ON
i.LINK
i.LINK
R
R
R
Sep. 11 (Wed
Rec to i.LINK
335-1 KDVR
Sep. 18 (Wed
Set Timer
35-1 PBPBP
Cancel
Sep. 18 (Wed
†
è
†
To Timer Mode
To select Rec or View
To Channel
è
†
To select the channel you want to set the timer for
To Date
è
†
To select the date
To Start Time
è
†
To set the start time
To End Time
è
†
To set end time
To Weekly/Daily
è
†
To select Once, Weekly, Daily(Sun.-Sat.), Daily(Mon.-Sat.) or Daily(Mon.-Fri.)
To Rec to i.LINK
è
To select ON or OFF
†
To Set Timer
Press the OK button
R
If you set the Rec on timer mode, set recording
title.
is added in front of the program
is added in front of the program
If you set the View on timer mode, set viewing
title.
V
Notes:
• In order for the i.LINK timer setting to work, you must set the clock on your television. See
page 60.
• When you want to edit the timer settings, see Timer Edit on page 78.
• When you have set a REC timer or VIEW timer, a PROGRAM indicator will light on the front
panel. While a timer is set, the indicator light will not turn off even if you turn the power off.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Timer Edit
When you want to confirm the timer you set or edited, or delete the timer setting, use this
function.
Timer Edition
Press the TIMER button
π†
To select the timer list you want to edit
Press the OK button
Timer Edit
Timer
Rec
Timer Mode
Channel
Date
35-1
V
New Reserva
Sep. 10 (wed)
5:00PM
Start Time
End Time
80-3 PBS1D
6:00PM
Sep. 11 (Wed
335-1 KDVR
Weekly/Daily
Weekly
ON
i.LINK
i.LINK
R
R
R
Sep. 11 (Wed
Rec to i.LINK
335-1 KDVR
Sep. 18 (Wed
Set Timer
35-1 PBPBP
Cancel
Delete
Sep. 18 (Wed
√®π† To change the setting you want to edit
†
To Set Timer
Press the OK button
Timer Deletion
Press the TIMER button
π†
π†
To select the timer list you want to delete
Press the OK button
To Delete
Press the OK button
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Cancel the timer recording
When you record a digital program now, you can cancel the recording.
Press the TIMER button
Timer
Sep. 10 (Wed) 4:55PM
Page 1/1
π†
To select the timer list you want to cancel
the recording
New Reservation
80-3
V
R
Do you want to terminate current program?
Press the OK button
Sept
335-
Sept
i.LINK
N
o
Y
e
s
The message "Do you want to
terminate current program ?" will
appear.
è
To select
YES: Cancel the recording
NO: Continue the recording
Press the OK button
Guide
You can view the program from the GUIDE.
Notes:
• The GUIDE function will only work when you are receiving digital programming only.
• The GUIDE will not show the correct time and date if you have not performed the set clock
function on your television. See page 58.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Information
Weak Signal
This OSD warning appears when the digital channel that you have selected is too weak to
receive or no signal is being detected for that channel.
Weak Signal
15
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Card Information
Cable card offers information when a cable card is inserted into the CABLE CARD slot on the
back of the TV.
Note:
• Please contact your local cable company regarding detailed information.
Cable Card Connection
CABLE CARD
ATSC
/DIGITAL CABLE IN
CABLE
TV Rear Panel
Note for inserting Cable Card:
• When you are watching a digital program, and if a weather or government emergency occurs,
the following may occur automatically regardless of what channel you were watching: the
channel may change, the screen will disappear or important text will appear on the screen.
The information is transmitted from EAS (Emergency Alert System), Firmware Upgrade of
Cable Card or compulsory HTML.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
No Program
If the TV channel you selected, or were watching is not receiving a signal, "NO PROGRAM"
appears on the television screen. It appears when that channel is not receiving a signal and you
have the Noise Muting function OFF and you have a single screen. It moves automatically every
two seconds to prevent the screen from burn-in. See page 6.
Note:
• Even if "NO PROGRAM" appears on the screen, your timer functions and auto shut off
functions that you set, are still active.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
CHECK
PROBLEMS
There is no power
• See if the power cord became unplugged.
• Check for a blown fuse or circuit breaker or a power outage.
There is no picture
or sound
• The antenna could be disconnected.
• The input mode could be set improperly. See page 62.
• The tuner (Auto Tuner Setup) could be set improperly. See page 35.
• The TV station may be having difficulties. Check to see if other stations are working.
Remote control is not • Check to see that the batteries are still working and properly installed.
operating properly or • Make sure the remote has a clear sight path to the TV.
at all
• Check that the TV/CATV switch is in the proper position.
• You may be too far from the TV. You must be within 23 feet (7 meters).
You cannot select a
certain channel
• Make sure the channels have been programmed. See "Channel Summary", page 36.
• Check to see if the channel is locked. See "Channel Summary - Lock" page 37.
The power turns off
by itself
• Make sure the set did not become unplugged.
• Perhaps the On/Off Timer is set. See page 59.
• Check to see if the Sleep Timer was set. See page 65.
The clock is wrong
• The power was interrupted and the clock was not reset. See page 58.
The color quality
is poor
• Tint and Color may be improperly adjusted. See page 55.
• The Video Status mode may be turned to the wrong setting. See page 64.
There are lines
across the picture
• There could be interference from another electrical appliance, such as a computer,
another TV or VCR. Move any such appliances further away from the TV.
• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
operating nearby. Move the antenna away from the appliance or change to a coaxial
cable connection which is less prone to interference.
The picture is spotted
There are double
pictures (ghosts)
• A building or passing airplane can reflect the original signal and produce a second,
slightly delayed one. Adjust your antenna position.
Picture is snowy
(image noise)
• Your antenna may be damaged, disconnected or turned. Check the antenna
connection. If the antenna is damaged, replace it.
Screen is 40% black
• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 47.
• Make sure the MTS settings are correct. See page 65.
Stereo or bilingual
programs can't be
heard
There is no sound
from the TV's
speaker
• The Center CH Input may be turned on. See page 54.
Static electricity
• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional
crackling sounds
• It is normal for the TV to make crackling sounds when first turned on or off. Unless
the sound or picture become abnormal, this is fine.
The AUTO DEMO
• The TV recieved a signal from the AV CompuLink
finished automatically • The On Timer that you programmed has started.
• The channel that the AUTO DEMO is using is a channel that is blocked by V-Chip.
• The Auto Shut Off that you programed has occured.
The square appears
and blinking
• It appears when you are operating the Auto Convergence. If not, then this may
be a problem with the Auto Convergence. Contact a service agent.
It does not operate
correctly
• Press the CHANNEL- and VOLUME- buttons on the front panel of the TV simultaneously
for a few seconds. The Digital Tuner will be reset. If this does not reset it correctly, unplug
the power cord and plug it back in.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
AV-56P785
AV-56P775
Model
AV-48P775
Type
Rear Projection Television
NTSC, BTSC System (Multi-Channel Sound)
ATSC Terrestrial, Digital Cable
Reception Format
Reception Range
VHF 2 to 13, UHF 14 to 69 CATV 135 Sub, Mid, Super, Hyper and
Ultra bands (191 channel frequency synthesizer system)
• Reception of channel A-5 ("95" of the TV set's on-screen cable channel
numbers) is not recommended for your TV set.
Power Source
AC 120V, 60 Hz
259W
Power Consumption
Screen Size
48 inch / 122 cm
56 inch / 142 cm
measured diagonally, 16:9 ratio
measured diagonally, 16:9 ratio
Speakers
13 cm round X 2
Audio Output
Full Range - 10W + 10W
Antenna Terminal
(VHF/UHF,
75 ohms (VHF/UHF)(F-type connector)
ATSC/DIGITAL
CABLE IN)
Video: 1 Vp-p, 75 ohms
External Input Jacks
Audio: 500 mVrms (-4dBs) high impedance
Component Input
Jack
Y: 1Vp-p positive, 75 ohms (negative sync provided)
Pb/Pr: 0.7 Vp-p 75 ohms
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
S-Video Input Jacks
Monitor/Recording
Output
Video: 1Vp-p, 75ohms
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
Audio: 250mVrms (-10dBs)
Fs-18dB Low Impedance
Audio Output Jacks
(FIX)
500mVrms (-4dBs) Low impedance (1000 Hz when modulated 100%)
Digital Out (optical) x 1
Optical Output
Digital Audio
TS IN/OUT (4-pin, S400) x 2
IEEE1394 compliant DTCP digital copy protection compatible
i.LINK In/Out Jack
AV CompuLink III
Jack
3.5 mm mini jack X 1
HDMI jack x 1
Digital–In
Note: The Digital–In terminal is not compatible with picture signals of a
personal computer
Dimensions (in)
W X H X D (cm)
47 1/4 x 46 7/8 x 24 1/2
120 x 118.9 x 62.2
53 7/8 x 51 1/8 x 26 3/8
136.8 x 129.6 x 66.7
Weight (lbs / kg)
Accessories
168 / 76
183 / 83
Illuminated remote control unit x 1 / AA batteries X 2
Two-way Splitter x 1 / RF Cable x 2
Specifications subject to change without notice.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
87
Download from Www.Somanuals.com. All Manuals Search And Download.
JVC COMPANY OF AMERICA
Division of JVC Americas Corp.
1700 Valley Road
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada, M1X 1A7
Wayne, New Jersey, 07470
Download from Www.Somanuals.com. All Manuals Search And Download.
|