JVC MP3 Player RV NB1 User Manual

POWERED WOOFER CD SYSTEM  
RV-NB1  
GROUP DOWN  
INSTRUCTIONS  
LVT1265-003B  
[B]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”  
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment,  
care must be taken if you are to obtain the best results and safety is to be assured.  
Do read the operating instructions before you attempt to use the equipment.  
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of  
equipment) are properly made in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when  
making or changing connections.  
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.  
Do be careful with glass panels or doors on equipment.  
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way—switch  
off, withdraw the mains plug and consult your dealer.  
DON’T remove any fixed cover as this may expose dangerous voltages.  
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended  
operation or has standby mode.  
Switch off using the switch on the equipment and make sure that your family know how to do this.  
Special arrangements may need to be made for infirm or handicapped people.  
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is  
illegal to watch television whilst driving.  
DON’T listen to headphones at high volume as such use can permanently damage your hearing.  
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.  
Overheating will cause damage and shorten the life of the equipment.  
DON’T use makeshift stands and NEVER fix legs with wood screwsto ensure complete safety always fit the manufacturer’s  
approved stand or legs with the fixings provided according to the instructions.  
DON’T allow electrical equipment to be exposed to rain or moisture.  
ABOVE ALL  
NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case—this could result in  
a fatal electrical shock.  
NEVER guess or take chances with electrical equipment of any kindit is better to be safe than sorry!  
G-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Thank you for purchasing the JVC Powered Woofer CD System.  
Before operating this system, read this manual carefully and thoroughly to obtain the best possible performance from your system, and retain  
this manual for future reference.  
Features  
Here are some of the things that make your system both powerful and simple to use.  
I General  
• With JVC’s COMPU PLAY you can turn on the system and automatically start the radio, disc player,  
or cassette deck with a single touch. (Only when AC power is used.)  
• Shoulder strap and carrying handle  
• ACS (Active Clear Sound) circuit for enhanced sound reproduction  
• Super woofer volume control that provides powerful bass  
• Sound mode control—reproducing various sound fields  
• Remote control unit that operates the disc, cassette, and tuner functions  
• Locking mechanism for disc and cassette door  
• Microphone/guitar input  
I Disc playback mode includes Skip Play, Search Play, Repeat Play, Random Play, and Program Play.  
I Cassette player having full logic cassette mechanism, auto reverse, and auto tape mechanism.  
I A 45-station preset capability (30 FM and 15 AM (MW/LW)) in addition to auto-seek and manual tuning.  
I Clock/timer functions, timer on/off with preset volume function, and sleep timer.  
IMPORTANT CAUTIONS  
1. Where to place the system  
I
• Select a place which is level, dry and neither too hot nor too cold (between 5°C and 35°C).  
• Leave sufficient distance between the system and a TV.  
• Do not use the system in a place subject to vibrations.  
2. Power cord  
I
• Do not handle the power cord with wet hands!  
• Some power is always consumed as long as the power cord is connected to the wall outlet.  
• When unplugging the system from the wall outlet, always pull the plug, not the power cord.  
3. When carrying the system  
I
• Remove a disc from the system.  
• Disconnect all the cords from the system.  
4. Malfunctions, etc.  
I
• There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.  
• Do not insert any metallic object into the system.  
• The system is not waterproof or dust proof.  
Table of contents  
II  
Features............................................................................ 1  
IMPORTANT CAUTIONS.............................................. 1  
Index of parts and controls.................................. 2  
Getting started....................................................... 4  
Basic operations ................................................... 7  
Listening to radio.................................................. 9  
Playing back discs ................................................ 10  
Playing back tapes................................................ 13  
Recording............................................................... 14  
Listening to an auxiliary equipment.................... 16  
Using the microphone/guitar ............................... 16  
Using the timer...................................................... 17  
Care and maintenance.......................................... 19  
Troubleshooting .................................................... 20  
Specifications........................................................ 20  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index of parts and controls  
II  
Display window  
o
;
a
s
d f g h j  
k
l
/ z  
x
c
1
7
8
2
3 4  
5
6
ON/  
STANDBY AUX SOUND  
BAND  
TUNER  
CD  
TAPE  
PRESET  
TUNING  
ONE TOUCH  
REC  
ACTIVE  
CLEAR SOUND  
MULTI CONTROL  
ACS  
ON LEVEL STANDBY  
BEAT CUT  
REW  
STOP  
FF  
e r t y  
u
i
9
p
q w  
See pages in parentheses for details.  
Display window  
o REC indicator (18)  
; Timer indicators (18)  
1 Shoulder strap hooks (4)  
2
ON/STANDBY button (7)  
(timer), ON, OFF  
a SLEEP indicator (17)  
s CLOCK indicator (8, 17)  
(reverse mode) indicator (13 – 15)  
f 2(reverse) tape direction indicator (13 – 15)  
indicator (15)  
3 AUX button (3, 16)  
• Pressing this button also turns on the unit.  
4 SOUND button (8)  
d
5 SUPER WOOFER VOLUME +/– control knob (8)  
6 LOCK/RELEASE knob (for disc) (10)  
7 Disc compartment door (10)  
8 VOLUME +/– control knob (7)  
9 PRESET TUNING/BEAT CUT button (9, 15)  
p ONE TOUCH REC button (15)  
q ACTIVE CLEAR SOUND button (8)  
w ACS (Active Clear Sound) indicators (8)  
• ON, LEVEL  
e LOCK/RELEASE knob (for deck) (13)  
r Cassette holder (13)  
t STANDBY indicator (7)  
y Remote sensor (4)  
u MULTI CONTROL buttons (9 – 15)  
g
h 3(forward) tape direction indicator (13 – 15)  
j FM mode indicators (9)  
• STEREO, MONO  
k MP3 indicator (11)  
l Repeat indicators (12)  
, ALL, GROUP  
/ Main display  
z PRGM (program) indicator (12)  
x RANDOM indicator (12)  
c Frequency unit indicators (8 – 9)  
• kHz, MHz  
4REW (rewind), 7STOP, ¢FF (fast-forward)  
i Source and play mode buttons (3, 9 – 15)  
• CD 6, TAPE 23, TUNER BAND  
Pressing one of these buttons also turns on the unit.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control  
See pages in parentheses for details.  
1 Number buttons (9, 11)  
2 SLEEP button (17)  
3 Multi control buttons (9 – 15, 17 – 18)  
ON/STANDBY  
GROUP UP,  
GROUP DOWN  
1
4
7
3
6
2
4, 7, ¢  
DISPLAY  
CANCEL  
SET  
4 Source buttons (3, 9 – 16)  
5
• AUX, CD 6, TAPE 23, TUNER BAND  
Pressing one of these buttons also turns on the unit.  
5 PLAY MODE button (12)  
8
9
10  
100  
GROUP UP  
10  
6 REPEAT button (12)  
CLOCK/TIMER  
SLEEP  
7 SOUND button (8)  
8 ACS (Active Clear Sound) button (8)  
GROUP DOWN  
9
ON/STANDBY button (7, 17 – 18)  
p DISPLAY button (8)  
q CANCEL button (12, 18)  
w SET button (10, 17 – 18)  
PLAY  
MODE  
REVERSE  
MODE  
FM  
MODE  
REPEAT  
e CLOCK/TIMER button (17 – 18)  
r FM MODE button (9)  
t REVERSE MODE button (13)  
y VOLUME +/– buttons (7)  
u SUPER WOOFER VOLUME +/– buttons (8)  
SUPER  
WOOFER  
VOLUME  
VOLUME  
SOUND  
RM-SRVNB1A REMOTE CONTROL  
COMPU PLAY — One Touch Operation  
With One Touch Operation you can play a disc, a tape, or turn on the radio with a single press of the play button for that function. The system  
turns on and starts playing the source if it is ready.  
The COMPU PLAY buttons are: On the system and remote control  
CD 6button  
TAPE 23button  
TUNER BAND button  
AUX button  
Note: The COMPU PLAY feature is not effective when the system is operated on batteries or car battery (DC12V).  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting started  
II  
Accessories  
Check that you have all the following items, which are supplied with the system.  
Power cord (1)  
Remote control (1)  
Batteries—R6(SUM-3)/AA(15F) (2)  
Shoulder strap (1)  
If any of these items are missing, contact your dealer immediately.  
Carrying the system  
I Using the carrying handles  
Be sure to hold both handles when you carry the system.  
If you carry the system by only one handle, because of the length  
of the system, the end may drag on the ground and be damaged as a  
result.  
I Using the shoulder strap  
Attach the supplied shoulder strap (adjustable in length) to each  
end of the system as illustrated.  
Shoulder strap  
Do not lift the system by the woofer ducts, and do not insert any  
metallic objects into them.  
2
1
Remote control  
Carrying handle  
Shoulder strap  
Woofer duct  
Remote control  
case  
To detach the shoulder strap, press in the metal fitting and unhook  
it from the shaft.  
Using the remote control — RM-SRVNB1A  
CAUTION:  
To avoid battery leakage or explosion:  
I Installing the batteries  
• Remove batteries when the remote control is not in use for an  
extended period of time.  
1
• When you need to replace the batteries, replace both batteries at  
the same time with new ones.  
• Do not use different types of batteries together.  
Point the remote control at the remote sensor on the system’s  
control panel (from a distance of up to 7 m). If you point the  
remote control from the slant direction, the distance will be  
shortened.  
• Do not expose the remote sensor to strong direct sunlight or  
artificial lighting.  
Match the polarity (+ and –) on the batteries with the +  
and – markings in the battery compartment.  
2
• Make sure there are no obstacles between the remote sensor and  
the remote control.  
Remote sensor  
R6(SUM-3)/AA(15F) (supplied)  
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
CAUTION: Make all connection before plugging the system into an AC power outlet.  
I Connecting the auxiliary equipment  
Pin-plug x 2  
Auxiliary  
equipment  
Stereo mini plug  
Signal cord  
(not supplied)  
I Connecting the microphone/guitar  
(not supplied)  
(not supplied)  
I Connecting to the car battery  
I Memory backup batteries  
1
2
To car’s cigarette  
lighter socket (DC12V)  
Car adapter (not supplied)  
Battery cover  
1
CAUTION:  
• Be sure to use the car adapter (not supplied) with the same polarity design  
as the one equipped with this system to prevent mishaps or damage.  
• For safety, stop the car before performing operations.  
• Be sure to start the engine when you use the car adapter; otherwise, the car  
battery will be exhausted.  
Match the polarity (+ and –) on the batteries  
with the + and – markings in the battery  
compartment.  
2
3
• During transport, stabilize the system in a box, etc.  
• To prevent malfunctions, do not leave the system in a car for a long time.  
• If the power is supplied through the car battery, the display will be blank  
with the system turned off (at standby).  
Unplug the AC power cord from the system to supply the power  
through the car battery; otherwise, the system does not work.  
“R6(SUM-3)/AA (15F)”  
size batteries (not  
supplied)  
I Connecting the AC power cord  
Power cord  
CAUTIONS:  
ONLY USE THE JVC POWER CORD PROVIDED WITH  
THIS SYSTEM TO AVOID MALFUNCTION OR  
DAMAGE TO THE SYSTEM.  
BE SURE TO UNPLUG THE POWER CORD FROM THE  
OUTLET WHEN GOING OUT OR WHEN THE SYSTEM  
IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
PHONES jack  
12V  
DC IN  
AC IN  
To remove the batteries, remove battery  
“10” first.  
To remove the batteries, remove battery  
“3” first.  
I Operating the system on  
batteries  
Notes:  
Notes:  
• When you operate the system on mains  
(AC) power or on car battery (DC12V), the  
power source automatically switches from  
batteries to AC or DC12V. However, you  
should remove the 10 batteries when  
operating on AC power or car battery  
(DC12V).  
• When the batteries are exhausted, the  
following symptoms will occur:  
- Mistracking occurs during disc playback.  
- Sounds are distorted intermittently during  
tape playback.  
- “DC OFF” flashes on the display, then the  
power goes off.  
If this happens, replace the batteries.  
• It is recommended to use AC power cord  
when recording important material or  
listening to a disc.  
• The memory backup batteries will not be  
consumed as long as the power is supplied  
from an AC outlet, loaded 10 batteries, or  
car battery (DC12V). However, if no power  
is supplied to the system, the memory  
backup batteries should be replaced with  
new ones approximately every 12 months to  
securely maintain the contents of the  
memory.  
• Before replacing the memory backup  
batteries, always connect the AC power  
cord to the system to prevent the contents of  
memory from being erased.  
1
Battery cover  
Match the polarity (+ and –) on the batteries  
with the + and – markings in the battery  
compartment.  
2
• When a power failure occurs, the time  
indication disappears from the display to  
save the battery power of the memory  
backup batteries.  
CAUTION:  
CAUTION:  
To avoid battery leakage or explosion:  
• When you need to replace the batteries,  
replace all batteries at the same time with  
new ones. Before replacing, you need to  
supply AC power to the system.  
• Do not use an old battery with new ones.  
• Do not use different types of batteries  
together.  
To avoid battery leakage or explosion:  
• Remove the 10 batteries when the system is  
not in use for an extended period of time.  
• When you need to replace the batteries,  
replace all batteries at the same time with  
new ones.  
“R20/D (13F)” size  
batteries (not supplied)  
• Do not use different types of batteries  
together.  
• If the power is supplied through the  
batteries, the display will be blank with the  
system turned off (at standby).  
3
Unplug the AC power cord from the  
system to supply the power through the  
batteries; otherwise, the system does  
not work.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operations  
II  
ON/STANDBY  
SUPERWOOFER  
VOLUME +/–  
DISPLAY  
VOLUME +/–  
SOUND  
ON/STANDBY  
STANDBY  
indicator  
SUPER WOOFER  
VOLUME +/–  
SOUND  
ACS  
ACS ON/LEVEL  
indicator  
ACTIVE CLEAR  
SOUND  
VOLUME +/–  
Turning off the system  
Turning the power on and off  
Press  
ON/STANDBY again.  
Note: The lighting condition for the STANDBY indicator and the  
The STANDBY indicator lights up when the system is operated on  
AC power.  
• When the AC power is used, the CLOCK indicator and the time  
are displayed without backlighting.  
display differs depending on the power source.  
Power source  
STANDBY indicator/display  
• The STANDBY indicator lights when  
power is turned off.  
• Backlighting of the display is illuminated  
when power is turned on.  
AC power  
STANDBY  
or  
• The STANDBY indicator does not light.  
• Backlighting of the display is not  
illuminated.  
• With the system turned off (at standby), no  
indication is shown on the display.  
Batteries or car  
battery (DC12V)*  
On system  
On remote control  
I Some power is always consumed even though power is turned  
off (called standby mode).  
I To disconnect the system from mains (AC) supply completely,  
unplug the AC power cord from the AC outlet. When you  
unplug the AC power cord, the clock will be reset to “0:00” if  
no memory backup batteries are installed.  
* If no source is playing and no operation is done for about  
4 minutes, “DC OFF” starts flashing on the display for about one  
minute before the system turns off automatically (except when  
the source is FM/AM or AUX, or when the microphone  
(or guitar) is used).  
Adjusting the volume  
You can adjust the volume level between 0 and 50.  
Turning on the system  
Press  
• When the system is operated on batteries or car battery (DC12V),  
press ON/STANDBY on the system.  
ON/STANDBY.  
Using the system  
Turn the VOLUME +/– control clockwise to increase the volume  
or turn it counterclockwise to decrease the volume.  
The STANDBY indicator goes out when the system is operated on  
AC power.  
The display comes on and the system is ready to continue in the  
mode it was in when the power was last turned off.  
STANDBY  
Using the remote control  
Press VOLUME + to increase the volume or press VOLUME – to  
decrease it.  
When you press and hold VOLUME + or –, the volume changes  
rapidly.  
or  
On system  
On remote control  
CAUTION: DO NOT start playing any source  
without first setting the volume to minimum, as a  
sudden blast of sound can damage your hearing,  
speakers and/or headphones.  
For private listening  
Connect a pair of headphones to the PHONES jack on the rear of  
the system (see page 6). No sound comes out of the speakers.  
Be sure to turn down the volume before connecting or putting on  
headphones.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the super woofer  
volume  
Selecting the sound mode  
Sound modes can be selected to enhance the type of music being  
played.  
During play, you can adjust the bass level between BASS 1  
(minimum) and BASS 6 (maximum).  
Press SOUND to select the sound mode.  
Each time you press the button, the sound mode changes as  
follows:  
Using the system  
Turn the SUPER WOOFER VOLUME +/– control clockwise to  
increase the bass level or turn it counterclockwise to decrease the  
bass level.  
SOUND  
SOUND  
or  
On system  
On remote control  
Sound mode selection:  
Using the remote control  
BEAT: Set to this position for music with a heavy beat, such as  
rock and disco music.  
Press SUPER WOOFER VOLUME + to increase the bass level or  
press SUPER WOOFER VOLUME – to decrease it.  
POP: Set to this position for light music including popular and  
vocal music.  
CLEAR: Set to this position for crisp and clear sounding music  
with transparent highs.  
FLAT (no effect): Set to this position when listening to classical  
music.  
Note: This function is not effective when the headphones are in  
use.  
Showing the time  
While the power is turned on, you can see the current time (clock)  
at any time, as follows.  
Activating clear sound  
The Active Clear Sound (ACS) circuit emphasize high-frequency  
sound without lowering the signal-noise ratio, while adjusting its  
output according to the input signal level. This results in a better  
balance between the high-frequency sound and the low-frequency  
heavy bass.  
Using the remote control  
Press DISPLAY. Each time you press the button, the display  
changes as follows:  
ACTIVE  
CLEAR SOUND  
ACS  
ON LEVEL  
Current sound source (e.g. FM103.50 MHz) =(clock) =(back to  
the beginning)  
or  
Note: To let the clock work, you need to set the clock first. (See  
On system  
On remote control  
“Setting the clock” on page 17.)  
Press ACS (active clear sound) on the system or on the remote  
control to turn it on or off. When it is turned on, the ACS ON  
indicator lights in red.  
The ACS LEVEL indicator blinks in green according to the input  
signal level.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to radio  
II  
Number buttons  
SET  
4
¢
TUNER BAND  
PRESET TUNING  
TUNER BAND  
FM MODE  
4
¢
You can listen to FM and AM (MW/LW) stations. Stations can be tuned in manually, automatically, or from preset memory storage.  
I Before listening to the radio, fully extend the FM telescopic antenna.  
Tuning in to a station  
Notice: To adjust the reception condition  
1. Press TUNER BAND.  
I
For FM: Adjust the FM telescopic antenna’s length, angle and  
The band and frequency you were last tuned into appear on the  
display.  
direction until the best reception is obtained.  
Each time you press the button, the band changes as follows:  
FM =AM =(back to the beginning)  
2. Select a station using one of the following  
I
methods.  
• When you tune into an FM stereo broadcast, the STEREO  
indicator lights up and you can hear stereo effect.  
If an FM stereo broadcast is hard to receive or  
noisy, press FM MODE on the remote control. The MONO  
indicator lights up and the sound becomes monaural, but the  
reception improves. When you tune in to another station, the  
MONO indicator goes off and stereo effect restores  
automatically.  
Note: AM broadcasts are monaural.  
I
I
Manual Tuning  
For AM: Change the direction of the system to obtain the best  
reception.  
Press 4or ¢repeatedly to move from frequency to  
frequency until you find the station you want.  
OR  
Placing the system near the window, for example, will  
improve AM reception.  
Auto Tuning  
Press and hold 4or ¢for one second or more.  
The frequency changes automatically until a station frequency  
is found.  
OR  
I
Preset Tuning (possible only after presetting stations)  
Select the desired preset number (displayed as “P-XX” on the  
display) using PRESET TUNING on the system or the number  
buttons on the remote control. After one second, the display  
will show the band frequency.  
(After one second)  
PRESET TUNING button: Each time you press the button, the  
preset number increases.  
Number buttons:  
To select P-5, press 5.  
To select P-15, press +10 then 5.  
To select P-20, press +10 once then  
press 10.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Presetting stations  
You can preset up to 30 FM stations and 15 AM (MW/LW)  
stations.  
4. Press the number buttons to select the  
Ipreset number you want.  
Note: Preset numbers may have been set to factory test  
frequencies prior to shipment. This is not a malfunction.  
You can preset the stations you want into memory by  
following one of the presetting methods below:  
5. Press SET.  
I
“STORED” appears on the display and the station is stored.  
6. Repeat above steps  
to  
for each  
5.  
1.  
Istation you want to store into memory with  
Using the remote control only  
a preset number.  
There is a time limit in doing the following steps. If the setting is  
To change the preset stations, repeat the same steps as  
above to overwrite a new station.  
canceled before you finish, start again from step  
.
3.  
1. Select a band (either AM or FM) by  
Ipressing TUNER BAND.  
CAUTION: To prevent the preset stations from  
being erased because of a power failure, etc.,  
install memory backup batteries in the system.  
(See pages 5 and 6.)  
2. Press 4 or ¢ to tune in to a station.  
I
3. Press SET.  
I
The preset station number starts flashing.  
Playing back discs  
II  
Number buttons  
CD 6  
LOCK/RELEASE knob  
CANCEL  
GROUP UP  
7
4
¢
CD 6  
GROUP DOWN  
PLAY MODE  
REPEAT  
¢
4
7
This system has been designed to play back the following  
discs—CD, finalized CD-R/CD-RW (recorded in audio CD  
format) and CD-R/CD-W (in MP3 format).  
Setting a disc  
• This system is not compatible with the other discs such as DVD,  
DVD-R, and DVD-RW.  
1. Turn the LOCK/RELEASE knob  
I
counterclockwise to open the disc  
compartment door.  
Notes on MP3:  
• The system can only recognize files (tracks) with “MP3” or  
“mp3” as the extensions, which can be in any combination of  
upper and lower case.  
• It is recommended that you record your material at a 44.1 kHz  
sampling rate, using the 128 kbps data transfer rate.  
You can play back the discs containing the tracks in music CD  
format or MP3 files in ISO 9660 format.  
• Some MP3 tracks or discs may not be played back because of  
their characteristics or recording conditions.  
2. Place a disc, with its label side up as  
I
shown above.  
• MP3 discs require a longer readout time than normal discs.  
3. Close the disc compartment door and turn  
I
the knob to “LOCK” position.  
To remove the disc, open the disc compartment door in stop  
mode.  
Hierarchy  
Level 3  
Level 1  
Level 2  
Level 4  
Level 5  
9
G 2  
G 4  
G 5  
I
I
You can place an 8 cm disc without an adapter.  
G 1  
(ROOT)  
10  
If the disc cannot be read correctly (because it is scratched, for  
example), “NO PLAY” or “NO DISC” appears on the display.  
You can place a disc while listening to the other source.  
3
7
8
G 3  
4
I
5
6
1
2
11  
12  
G 6  
Group with its play order  
G 1  
1
MP3 track with its play order  
• This system recognizes up to 999 tracks on a disc (or less  
depending on the recording condition of a disc).  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Skip Play  
Using the disc playerNormal  
Play  
During playback, press 4or ¢to select the track you want to  
play.  
• Press ¢once to skip to the beginning of the next track.  
• Press 4to skip to the beginning of the track being played.  
Press 4twice quickly to skip to the beginning of the previous  
track.  
You can also select a track in stop mode with the same buttons.  
For CD: Selected track and its playback time are shown on the  
display.  
To play a disc  
1. Set a disc.  
I
2. Press CD 6.  
I
The first track of the disc starts playing.  
For CDs:  
Track  
number  
Playback  
time  
For MP3:Group and track numbers (then ID3 Tag if any) are  
shown on the display.  
To start playback, press CD 6.  
For MP3 discs:  
Search Play  
Press and hold 4or ¢, during playback, will fast forward/  
backwards the disc so you can quickly find a particular passage in  
the track you are listening to. During search play, you can hear the  
sound of approx. one forth level.  
MP3 indicator  
• When playing an MP3 disc, the file name (then ID3 Tag if  
any) is displayed at the beginning of each track.  
• If no disc is inserted, “NO DISC” appears on the display and  
the system remains in stop mode.  
• The system automatically stops when the last track of the disc  
has finished playing.  
To locate a track directly using the  
remote control only  
Press the number buttons to directly play a track.  
• To directly play track 5, press 5.  
To stop playing the disc, press 7.  
The following information for the disc is displayed.  
• To directly play track 15, press +10 then 5.  
• To directly play track 20, press +10 once then press 10.  
For CDs:  
(Only for MP3 discs)  
• To directly play track 109, press +100 once then press 9.  
• To directly play track 125, press +100, +10, +10 then 5.  
Total track  
number  
Total playback  
time  
To select a group (for MP3 disc)  
using remote control only  
For MP3 discs:  
Total group  
number*  
Total track  
number  
While playing an MP3 disc, press  
GROUP UP or  
GROUP DOWN to select the group you want to play.  
• Press  
• Press  
GROUP UP to skip to the next group.  
MP3 indicator  
GROUP DOWN to skip to the previous group.  
* If a disc includes more than 99 groups, “G – –” will appear  
on the display.  
You can also select a group in stop mode with the same buttons.  
To play the group after selection, press CD 6.  
To pause, press CD 6. The playback time blinks on the  
display.  
To cancel pause, press the same button again. Playback  
continues from the point where it was paused.  
Note: Do not turn the LOCK/RELEASE knob during playback.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming the playing order  
of the tracks  
Random play  
The tracks will play in no special order when you use this mode.  
Using the remote control  
1. Set a disc.  
I
2. Press CD 6.  
I
3. Press 7 to stop the disc.  
I
Using the remote control  
I You can program up to 50 tracks in any desired order including  
the same tracks.  
I You can only make a program when the system is stopped.  
I While making a program, you cannot specify a group number to  
select a track.  
4. Press PLAY MODE repeatedly to select  
I
1. Set a disc.  
I
RANDOM.  
2. Press CD 6.  
I
The RANDOM indicator lights up on the display.  
3. Press 7 to stop the disc.  
5. Press CD 6.  
I
I
The tracks are played in random order once.  
4. Press PLAY MODE repeatedly to select  
I
PROGRAM.  
To skip a track during playback, press ¢to skip to another  
track in the random sequence. The 4button works only to go  
back to the beginning of the current track.  
The system enters the programming mode and the  
PRGM indicator lights up.  
While stopped:  
5. Press the number buttons to select the  
I
I To exit from random mode, press PLAY MODE repeatedly  
until the track number and total playback time appear on the  
display.  
track to program.  
• For detailed operations, see “To locate a track directly using  
the remote control only” on page 11.  
Each time you press the button, the play mode changes as follows:  
Example: for track 7, press 7.  
Normal play =PROGRAM =RANDOM =(back to the  
beginning)  
Last programmed track  
Program order number  
Repeating tracks  
You can repeat the tracks or individual track as many times as you  
like.  
(After 2 seconds)  
Total playback time of the programmed tracks*  
Using the remote control  
* Total playback time will not appear while making a  
program using an MP3 disc.  
Press REPEAT.  
Each time you press the button, repeat indicator changes as  
follows:  
6. Repeat step  
to select other tracks for  
5.  
I
I Repeat mode remains in effect even when you change the play  
the program.  
mode.  
For CDs:  
• To cancel the last track programmed, press CANCEL once.  
7. Press CD 6.  
I
ALL =  
= canceled =(back to the beginning)  
: Repeats all the tracks on the disc.  
: Repeats the current track.  
The system plays the tracks in the order you have programmed  
them.  
ALL  
I
You can skip to a particular program track by pressing  
4or ¢during program play.  
For MP3 discs:  
While stopped:  
ALL =  
beginning)  
ALL  
GROUP =  
= canceled =(back to the  
I To confirm the programmed tracks, press 4or ¢  
repeatedly; the tracks making up the program will successively  
be displayed in the programmed order.  
: Repeats all the tracks on the disc.  
GROUP : In normal play mode, repeats all the tracks in a  
group.  
• To add a track to the end of the program, simply press the  
number buttons.  
In program and random play modes, group  
repeat cannot be selected.  
I To delete the tracks in the program, press CANCEL  
repeatedly. Each time you press the button, the last track will be  
erased.  
: Repeats the current track.  
I To delete the entire program, press and hold CANCEL  
until “CLEAR!” appears on the display.  
To exit from repeat mode, press REPEAT until the repeat  
indicator on the display goes out.  
• Turning off the power will clear the program.  
I To exit from program mode, press PLAY MODE  
repeatedly until the track number and total playback time  
appear on the display.  
Each time you press the button, the play mode changes as follows:  
Normal play =PROGRAM =RANDOM =(back to the  
beginning)  
Note:  
(For CDs) If the total playback time of the programmed tracks  
exceeds 99 minutes 59 seconds, “– – : – –” will appear on the  
display.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing back tapes  
II  
TAPE 23  
7
4
¢
TAPE 23  
¢
REVERSE  
MODE  
LOCK/RELEASE  
knob  
4
7
With automatic tape direction, you can listen to type I or II tapes  
without having to change any settings.  
5. If you need to change the playback  
I
direction, press TAPE 2 3.  
The opposite side tape direction indicator lights up and the tape  
playback direction changes.  
The use of tapes longer than 120 minutes is not recommended,  
since characteristic deterioration may occur and these tapes  
easily jam in the pinch-rollers and the capstans.  
To stop playing, press 7.  
To remove the tape, stop the tape, and open the cassette  
holder by turning the LOCK/RELEASE knob to the  
“RELEASE” position.  
Regular play  
1. Turn the LOCK/RELEASE knob  
I
Notes:  
counterclockwise to open the cassette  
holder.  
• Do not turn the LOCK/RELEASE knob during playback.  
• When no tape is loaded in the deck, “NO TAPE” appears on  
the display.  
To fast-wind/rewind a tape  
Press ¢or 4to fast-wind/rewind the tape.  
• The cassette deck automatically stops when the tape reaches its  
end.  
2. Put the cassette in, with the side you want  
I
to listen facing you.  
Reverse mode  
You can set a tape to play just one side, both sides in succession, or  
both sides continuously.  
Using the remote control  
Press REVERSE MODE.  
Each time you press the button, reverse mode indicator changes as  
follows:  
=
=
=(back to the beginning)  
3. Close the holder gently and turn the knob  
I
: The cassette deck automatically stops after playing  
one side of the tape.  
to LOCKposition.  
4. Press TAPE 2 3.  
I
: The cassette deck automatically stops when playback  
in the reverse (2) direction is finished.  
The tape is played in the direction shown by the tape direction  
indicator.  
: The cassette deck continues to play both sides of the  
tape until the 7button is pressed.  
3(Forward playback): The side of the tape facing you is  
played back.  
2(Reverse playback): The opposite side of the tape is  
played back.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
II  
TAPE 23  
CD 6  
7
AUX  
CD 6  
TAPE 23  
TUNER  
AUX  
TUNER  
REVERSE  
MODE  
PRESET TUNING/  
BEAT CUT  
7
ONE TOUCH REC  
Things to know before you start  
recording  
Standard recording  
You can record any sound source to tape.  
I It should be noted that it may be unlawful to re-record  
pre-recorded tapes, records, or discs without the  
consent of the owner of copyright in the sound or  
video recording, broadcast or cable programme and  
in any literary, dramatic, musical, or artistic work  
embodied therein.  
The sources are disc, tuner, auxiliary equipment, microphone, and  
guitar. The microphone sound and guitar sound can be mixed with  
any source.  
1. Insert a blank or erasable cassette tape  
I
into the cassette deck.  
I When you want to record onto both sides of a tape, you can set  
Be sure that the tape direction indicator and the tape insertion  
reverse mode to  
. Recording automatically stops after  
direction are as follows:  
recording in the reverse (2) direction. Therefore, make sure  
that the tape direction is forward (3) when recording with  
reverse mode is on.  
[Forward and reverse recording]  
Tape direction indicator  
Tape insertion direction  
I The recording level is automatically set correctly, so it is not  
affected by the VOLUME control on the system or by adjusting  
the sound effects. Thus, during recording you can adjust the  
sound you are actually listening to without affecting the  
recording level.  
I Two small tabs on the back of the cassette tape, one for side A  
and one for side B, can be removed to prevent accidental erasure  
or recording.  
3
(Forward)  
* Recording will be made on  
the tape side facing you.  
(Front view)  
I To record on a cassette with the tabs removed, you must cover  
the holes with adhesive tape first. However, when a type II tape  
is used, only cover part of the hole as shown, since the other part  
of the hole (type II detection slot) is used to detect the tape type.  
2
(Reverse)  
* Recording will be made on  
Type II detection  
slot  
the opposite side of the tape.  
(Front view)  
• If the tape direction 2(reverse) is lit, press TAPE 23to change  
the direction. (In this case, since the tape play starts, you need to  
press 7. Then, press 4to rewind the tape up to the end point of  
the leader tape which cannot be recorded onto.)  
Adhesive tape  
I Type I and type II tapes can be used for recording.  
• If the inserted tape is not fully rewound, press 4to rewind the  
tape up to the end point of the leader tape which cannot be  
recorded onto.  
Note:  
At the start and end of cassette tapes, there is leader tape which  
cannot be recorded onto. Thus, before recording, wind on the  
leader tape first to ensure getting the beginning of the recording.  
2. If you want to record on both sides of the  
I
tape, press REVERSE MODE on the remote  
control to set the cassette deck in reverse  
mode.  
CAUTION: If a recording you make has excessive  
noise or static, the system may have been too  
close to a TV which was on during the recording.  
Either turn off the TV or increase the distance  
between the TV and the system.  
Press the button until “  
” is lit.  
3. Prepare the source, for example, tuning in  
I
to a radio station, or turning on the  
connected auxiliary equipment.  
Note: For disc recording, refer to “Disc direct recording”  
described on page 15.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Press ONE TOUCH REC on the system.  
6. Choose whether to have pauses between  
I
I
tracks.  
The  
indicator lights up and the system starts recording.  
• If nothing is done, a non-recorded pause of about four  
seconds will be automatically made between tracks.  
• If you do not want pauses between tracks, press CD 6  
twice to enter pause mode—only possible with CDs.  
• If the tab of the cassette tape is removed to protect erasure or  
recording, recording does not start.  
Tips: When you want to record on both sides of the tape, start  
recording from the forward direction.  
7. Press ONE TOUCH REC on the system.  
To stop at any time during the recording process, press 7.  
I
The  
indicator lights up and the cassette deck starts  
Recording an AM station on a tape  
When recording an AM broadcast, beats may be produced which  
are not heard when listening to the broadcast. If this happens, press  
BEAT CUT to eliminate the beats.  
1. Set to AM station and start recording.  
2. Press BEAT CUT to eliminate the beats.  
recording.  
• When the tape reaches its end at the middle of a song in the  
forward direction (3), the recording in the reverse direction  
(2) will start from the beginning of that track (or previous  
track). See diagram below.  
Ex.: Case 1  
Each time you press the button, the display changes as follows:  
B.CUT-1 =B.CUT-2 =B.CUT-3 =B.CUT-4 =(back to  
the beginning)  
[Recording direction 3(forward)]  
Tape end  
Disc direct recording  
Everything on the disc goes onto the tape in the order it is on the  
disc, or according to the order you have set in a program.  
Track 1  
Track 2  
more than 10 seconds  
1. Insert a blank or erasable cassette tape  
I
into the cassette deck.  
* The recording in reverse side (2) starts from the beginning  
Be sure that the tape direction indicator and the tape insertion  
of track 2.  
direction are as follows:  
Ex.: Case 2  
[Recording direction 3(forward)]  
[Forward recording]  
Tape end  
Tape direction indicator  
Tape insertion direction  
Track 1  
Track 2  
3
(Forward)  
* Recording will be made on  
less than 10 seconds  
the tape side facing you.  
* The recording in reverse side (2) starts from the beginning  
of track 1.  
(Front view)  
• After the disc player has played the entire disc, or all the  
programmed tracks, the tape automatically stops.  
• Recording will also stop when the end of the reverse side (2)  
is reached (even if the disc play is not yet over).  
2. If you want to record on both sides of the  
I
tape, press REVERSE MODE on the remote  
control to set the system in reverse mode.  
Press the button until “  
” is lit.  
To stop at any time during the recording process, press 7.  
3. Set a disc.  
The tape stops after four seconds.  
I
Note:  
4. Press CD 6.  
I
When making SLEEP timer settings while performing disc direct  
recording, set enough time to allow the disc to finish playing;  
otherwise, the power will go off before recording is completed.  
5. Press 7.  
I
• If you want to record specific tracks only, program the tracks  
first. You can check their total playback time on the display  
during programming. (See page 12.)  
One Track Recording  
You can record the current track being played.  
1. Insert a blank or erasable cassette tape  
I
into the cassette deck.  
2. Play the track you wish to record.  
I
3. Press ONE TOUCH REC on the system.  
I
The disc player returns to the beginning of that track and the  
track is recorded on the tape. After recording, the disc player  
and the cassette deck automatically stop.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to an auxiliary equipment  
II  
AUX  
AUX  
Listening to external equipment  
You can listen to an auxiliary equipment.  
• First make sure that the auxiliary equipment is properly  
connected to the system. (See page 5.)  
3. Adjust the volume to the desired listening  
I
level.  
4. Apply sound effects, if you wish.  
I
1. Set the volume level to minimum.  
I
I
Adjust the super woofer volume to reinforce the bass sound.  
2. Press AUX.  
Note: For operation of the auxiliary equipment, refer to its  
I
“AUX” appears on the display.  
instructions.  
• To listen to the auxiliary equipment, start playing the auxiliary  
equipment.  
Using the microphone/guitar  
II  
5. Adjust the VOLUME +/control and the  
I
Microphone/guitar mixing  
MIC/GUITAR LEVEL control, as you play the  
microphone or the guitar.  
Using a microphone or a guitar (not supplied), you can mix its  
sound with a source sound.  
CAUTION: DO NOT connect a bass guitar to the  
MIC/GUITAR INPUT jack, as it may damage the  
system.  
1. Make sure the MIC/GUITAR LEVEL control  
I
on the rear of the system is properly set.  
• When using a microphone, make sure the knob is pressed in  
(_).  
Recording microphone or  
guitar mixing on a tape  
• When using a guitar, make sure the knob is released ().  
2. Set the MIC/GUITAR LEVEL control to MIN  
I
1. Follow the above steps  
1. 5.  
I
by turning it fully counterclockwise.  
2. To record, follow the steps in Standard  
I
3. Connect a microphone or a guitar into the  
I
recording. (See page 14.)  
MIC/GUITAR INPUT jack on the rear of the  
system.  
Note: If “howling” occurs when using the microphone, keep the  
microphone away from the speaker.  
4. Start a source: disc, tape, tuner, or other  
I
equipment.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the timer  
II  
Setting the sleep timer  
ON/STANDBY  
CANCEL  
Use the sleep timer to turn the system off after a certain number of  
minutes when it is playing. By setting the sleep timer, you can fall  
asleep to the music and know that your system will turn off by  
itself rather than playing all night.  
SET  
CLOCK/TIMER  
¢
SLEEP  
4
I You can set the sleep timer only when the system is turned on.  
Using the remote control only  
1. Press SLEEP.  
I
The SLEEP indicator lights up on the display.  
The timers let you control the listening and recording functions  
automatically.  
Setting the clock  
When the power is first supplied, the CLOCK indicator and “0:00”  
blink on the display. Set the clock.  
2. Set the length of time you want the source  
Note:  
I
to play before shutting off.  
• Each time you press the button, it changes the number of  
minutes shown on the display in this sequence:  
10 =20 =30 =60 =90 =120 =OFF =(back to the  
beginning)  
The clock must be correctly set for the timers to work.  
Using the remote control only  
1. Press  
ON/STANDBY.  
I
After setting the number of minutes for the sleep timer, the  
indication will stop blinking and goes off.  
The system is now set to turn off after the number of minutes you  
set.  
2. Press CLOCK/TIMER repeatedly until the  
I
CLOCK indicator lights up.  
The hour digit blinks on the display.  
3. Press ¢ or 4 to select the hour.  
I
To confirm the sleep time:  
When SLEEP is pressed, the remaining sleep time is displayed.  
Wait until the display returns to the original display.  
When you press and hold the button, the hour digit changes  
continuously.  
To cancel the sleep timer:  
Press SLEEP repeatedly to select “OFF”. Turning off the system  
also cancels the sleep timer.  
4. Press SET to set the hour.  
I
The minutes digits start flashing on the display.  
5. Press ¢ or 4 to select the minute.  
I
When you press and hold the button, the minute digit changes  
continuously.  
6. Press SET to finish setting the clock.  
I
CAUTION: If memory backup batteries are  
exhausted or not installed, and the AC power  
cord is plugged in again after being  
disconnected, or power is restored after a power  
failure, the CLOCK indicator will blink on the  
display. Set the current time (clock) again.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Press ¢ or 4 to select the music source  
I
Setting the daily timer  
you want to listen to, then press SET.  
Each time you press the button, the display changes as shown  
below:  
Once the timer has been set, it will be activated at the same time  
everyday until the timer is turned off. Recording timer works only  
one time.  
TUNER =TU\TAPE =CD =TAPE =(back to the  
beginning)  
• While the timer is being set, the timer indicator (  
• While the timer has been set, the timer indicator (  
up if the power is supplied through the AC outlet.  
• While the timer is working, the timer indicator (  
) lights up.  
) also lights  
When you select the “TU\TAPE”;  
• The REC indicator appears on the display.  
• The timer will be canceled after tuner recording has been  
finished.  
) blinks.  
Using the remote control only  
7. Press ¢ or 4 to select the volume level,  
I
1. Press  
I
ON/STANDBY.  
then press SET.  
2. Press CLOCK/TIMER.  
I
– –  
: The current volume level will be used.  
“TIMER ON?” appears.  
0 to 50 : When the timer is turned on, the volume will be  
automatically set to the selected level.  
• Press SET to activate the timer setting you have made before.  
• Press CANCEL to cancel the timer.  
• Go to the next step to reset the timer (or set the timer first  
time).  
3. Press CLOCK/TIMER again, so that the  
I
• The current timer setting appears for confirmation.  
timer indicator ( ) and ON indicator light  
up.  
8. Before turning off the system, prepare the  
I
The hour digit of the current ON time blinks on the display.  
music source selected in step  
.
6.  
TUNER  
: Tune into the desired station.  
TU\TAPE : The last tuned station will be recorded. Insert a  
cassette tape for recording the station.  
CD  
: Set a disc.  
TAPE  
: Insert a tape.  
4. Set the on-time you want the system to  
I
9. Press  
ON/STANDBY to turn off the  
I
turn on.  
system.  
• When the timer turns on, the volume level gradually increases  
from 0 (zero) to the preset level in step  
However, if the volume has been set to “– –”, the volume  
level will be set to the last level directly.  
.
7.  
To cancel the operation, press CLOCK/TIMER until the  
display returns to the original one.  
(1) Press ¢or 4to select the hour, then press SET.  
(2) Press ¢or 4to select the minute, then press SET.  
The OFF indicator lights up.  
To cancel the timer, press CLOCK/TIMER once, then press  
• Press and hold the button will change the time rapidly.  
• If you want to change the time setting, press  
CANCEL.  
CANCEL. (“TIMEROFF” appears, only when power is on.)  
To reactivate (or confirm) the canceled timer, press  
CLOCK/TIMER once, then press SET. (The current timer setting  
appears for confirmation.)  
5. Set the OFF time (example: 1:30).  
I
Notes:  
• The timer cannot be set if on-time and off-time are the same.  
• The timer does not work if the system is not in the standby mode  
(the system needs to be in standby mode at least one minute  
before the on-time).  
(1) Press ¢or 4to select the hour, then press SET.  
(2) Press ¢or 4to select the minute, then press SET.  
• Press and hold the button will change the time rapidly.  
• If you want to change the time setting, press  
CANCEL.  
CAUTION: If memory backup batteries are  
exhausted or not installed, and the AC power  
cord is disconnected or there is a power failure,  
time settings will be erased from memory. If this  
happens, set the current time (clock) and  
perform the timer setting again.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and maintenance  
II  
Handle your discs carefully, and they will last a long time.  
• If there are fingerprints, etc. on the lens, gently wipe clean with a  
cotton swab.  
Compact discs  
• Only discs bearing this mark can be used with  
this system. However, continued use of  
irregular shape discs (heart-shape, octagonal,  
etc.) can damage the system.  
Moisture condensation  
Moisture may condense on the lens inside the  
system in the following cases:  
• Remove the disc from its case by holding it at  
the edges while pressing the case’s center hole  
lightly.  
• Do not touch the shiny surface of the disc, or  
bend the disc.  
• After turning on heating in the room.  
• In a damp room.  
• If the system is brought directly from a cold to  
a warm place.  
Should this occur, the system may malfunction.  
In this case, leave the system turned on for a few  
hours until the moisture evaporates, unplug the  
AC power cord, and then plug it in again.  
• Put the disc back in its case after use to  
prevent warping.  
• Be careful not to scratch the surface of the disc  
when placing it back in the case.  
• Avoid exposure to direct sunlight,  
temperature extremes, and moisture.  
Cassette tapes  
• If the tape is loose, it may get stretched, cut, or  
caught in the cassette. Take up the slack by  
inserting a pencil in one of the reels and  
rotating.  
• A dirty disc may not play correctly. If a disc  
does become dirty, wipe it with a soft cloth in a  
straight line from center to edge.  
• Do not touch the tape surface.  
CAUTION: Do not use any solvent (for example,  
conventional record cleaner, spray thinner,  
benzine, etc.) to clean a disc.  
• Do not store the tape:  
- In dusty places  
- In direct sunlight or heat  
- In moist areas  
General notes  
In general, you will have the best performance by keeping your  
discs and the mechanism clean.  
• Store discs in their cases, and keep them in cabinets or on shelves.  
• Keep the disc compartment door closed when not in use.  
- On a TV or speaker  
- Near a magnet  
Cassette deck  
Cleaning the lens  
• If the heads, capstans, or pinch-rollers of the cassette deck  
become dirty, the following may occur:  
- Loss of sound quality  
If the lens in the pickup is dirty, dropout, etc., could degrade sound.  
Open the disc compartment door and clean the lens as shown.  
• Use a blower (available from a camera store) to blow dust off the  
lens.  
- Discontinuous sound  
- Fading  
- Incomplete erasure  
- Difficulty recording  
• Clean the heads, capstans, and pinch-rollers using a cotton swab  
moistened with alcohol.  
Blower  
Lens  
Capstans  
Pinch-rollers  
Erase head  
Record/play head  
• If the heads become magnetized, the system will produce noise or  
lose high frequency notes.  
• To demagnetize the heads, turn off the system, and use a head  
demagnetizer (available at electronics and record shops).  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
If you are having a problem with your system, check this list for a possible solution before calling for service.  
If you cannot solve the problem from the hints given here, or the system has been physically damaged, call a qualified person, such as your  
dealer, for service.  
II  
Symptom  
Possible cause  
Action  
Power does not come on.  
The power cord is not connected to an AC  
outlet.  
Insert the plug into the socket.  
No sound is heard.  
• Connections are incorrect, or loose.  
• Check all connections and make  
corrections. (See page 5.)  
• Headphones are connected.  
• MP3 disc is recorded with “packet  
writing.”  
• Disconnect the headphones.  
• It cannot be played. Replace the disc.  
Poor FM reception.  
The track skips.  
The FM telescopic antenna is not properly  
extended and positioned.  
Fully extend the FM telescopic antenna  
and turn it for the best reception.  
The disc is dirty or scratched.  
Clean or replace the disc.  
The disc does not play (“NO PLAY” or  
“NO DISC” appears).  
• The disc is upside down.  
• The disc is dirty or scratched.  
• Put the disc in with the label side up.  
• Change the disc.  
Specific files on an MP3 disc are not  
played.  
Files other than MP3 are included in the  
disc.  
They cannot be played.  
Unable to record.  
Cassette record protect tabs are removed.  
Cover the holes on the back edge of the  
cassette with tape.  
Unable to operate the remote control.  
• The path between the remote control and  
the sensor on the system is blocked.  
• The batteries have lost their charge.  
• Remove the obstruction.  
• Replace the batteries.  
Operations are disabled.  
The built-in microprocessor has  
malfunctioned due to external electrical  
interference.  
Unplug the system then plug it back in  
after a few minutes.  
The cassette holder cannot be opened.  
During tape play, the power cord has been  
unplugged.  
Plug in the power cord and press the  
ON/STANDBY button.  
Indicators and the display do not light up  
while in standby mode.  
Batteries or DC power is used to supply  
the power.  
Specifications  
II  
Amplifier  
Output Power  
(Max.)  
Tuner  
FM Tuner  
20 W (10 W + 10 W) at 4 (full range),  
40 W (20 W + 20 W) at 4 , 60 Hz (woofer)  
10 W (5 W + 5 W) at 4 (full range),  
Tuning Range  
AM Tuner  
87.50 MHz – 108.00 MHz  
(10% THD)  
Tuning Range  
(MW) 522 – 1 629 kHz  
30 W (15 W + 15 W) at 4 , 60 Hz (woofer)  
(LW) 144 – 288 kHz  
Input Sensitivity/Impedance (1 kHz)  
AUX IN 300 mV/47 kΩ  
MIC/GUITAR INPUT: Switchable  
Antenna  
FM telescopic antenna  
Ferrite core antenna for AM (MW/LW)  
Speakers  
Full range  
Super woofer  
MIC  
200 – 2 k(6.3 mm dia. plug)  
100 k– 1 M(6.3 mm dia. plug)  
8 cm × 2, 4 Ω  
16 cm × 2, 4 Ω  
GUITAR  
Output Sensitivity/Impedance (1 kHz)  
Phones  
16 – 1 kΩ  
General  
Dimensions  
Mass  
0 – 12 mW/ch output into 32 Ω  
690 mm × 239 mm × 296 mm (W/H/D)  
9.5 kg (without batteries)  
10.6 kg (with batteries)  
Cassette Deck  
Frequency Response  
Type II (High position) 60 Hz – 14 kHz  
Power Specifications  
Wow and Flutter  
0.15% (WRMS)  
Power Requirements AC 230 V  
, 50 Hz  
DC15V (“R20/D (13F)” batteries (10))  
External DC12V (car battery via  
optional car adapter)  
Disc Player  
Dynamic range  
90 dB  
Signal-to-noise ratio 95 dB  
Wow and Flutter Unmeasurable  
Power Consumption 43 W (power on mode)  
1.6 W (in standby mode)  
Design and specifications are subject to change without notice.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
© 2004 Victor Company of Japan, Limited  
0704NSMMDWJEIN  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Refrigerator Two Door Refrigerator Freezer User Manual
Intel Mouse ET900 User Manual
ION Scanner FILM2SD User Manual
Jenn Air Range GAS DOWNDRAFT SLIDE IN RANGE User Manual
JVC Car Speaker KD A95BT User Manual
JVC CRT Television AV 1414EE AV 2134EE AV 1434EE AV 1434TEE AV 2104EE AV 2104TEE AV 2114EE AV 2134TEE AV 2124EE User Manual
JVC Home Theater System SP PWC40 User Manual
Kenwood Marine Radio TH 255A User Manual
King Canada Drill KC 30FC User Manual
Kodak Battery Charger K630 User Manual