JVC MP3 Docking Station 0397MKVUNVP User Manual

JLIP VIDEO CAPTURE DOCKING STATION

GV-DS1

INSTRUCTIONS

LYT0002-0J9A

Download from Www.Somanuals.com. All Manuals Search And Download.

Dear Customer,

IMPORTANT

Thank you for purchasing this VIDEO CAPTURE

DOCKING STATION. Before use, please read

the safety information and precautions

contained in the following pages to ensure safe

use of this product.

Connection to the mains supply in the United

Kingdom.

DO NOT cut off the mains plug from this equip-

ment. If the plug fitted is not suitable for the

power points in your home or the cable is too

short to reach a power point, then obtain an

appropriate safety approved extension lead or

consult your dealer.

Using This Instruction Manual

•All major sections and subsections are listed in

the Table Of Contents (੬ pgs. 6, 7).

•Notes appear after most subsections. Be sure to

read these as well.

BE SURE to replace the fuse only with an

identical approved type, as originally fitted,

and to replace the fuse cover.

If nontheless the mains plug is cut off ensure to

remove the fuse and dispose of the plug

immediately, to avoid a possible shock hazard

by inadvertent connection to the mains supply.

If this product is not supplied fitted with a

mains plug then follow the instructions given

below:

DO NOT make any connection to the Larger

Terminal coded E or Green.

The wires in the mains lead are coloured in

accordance with the following code:

•Basic and advanced features/operation are

separated for easier reference.

It is recommended that you . . .

..... refer to "Controls and Connectors" (੬ pg. 10 –

11) and familiarize yourself with connector

locations before use.

..... read thoroughly the Safety Precautions and

CAUTIONS that follow. They contain ex-

tremely important information regarding the

safe use of your new VIDEO CAPTURE

DOCKING STATION.

Blue to N (Neutral) or Black

Brown to L (Live) or Red

If these colours do not correspond with the

terminal identifications of your plug, connect

as follows:

Blue wire to terminal coded N (Neutral) or

coloured black.

Brown wire to terminal coded L (Live) or

coloured Red.

If in doubt — consult a competent electrician.

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY

SOME DO’S AND

PRECAUTIONS

DON’TS ON THE SAFE

USE OF EQUIPMENT

WARNING:

This equipment has been designed and manufac-

tured to meet international safety standards but,

like any electrical equipment, care must be taken

if you are to obtain the best results and safety is

to be assured.

TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE

THIS UNIT TO RAIN OR

MOISTURE.

read the operating instructions before you

attempt to use the equipment.

ensure that all electrical connections

(including the mains plug, extension leads and

interconnections between pieces of equip-

ment) are properly made and in accordance

with the manufacturer’s instructions. Switch

off and withdraw the mains plug when making

or changing connections.

CAUTIONS:

Ⅲ To prevent shock, do not open the cabinet.

No user serviceable parts inside. Refer

servicing to qualified personnel.

consult your dealer if you are ever in doubt

about the installation, operation or safety of

your equipment.

be careful with glass panels or doors on

equipment.

Ⅲ When you are not using the AC Power

Adapter/Battery charger for a long period of

time, it is recommended that you disconnect

the power cord from AC outlet.

DON’Tcontinue to operate the equipment if you are in

any doubt about it working normally, or if it is

damanged in any way — switch off, withdraw

the mains plug and consult your dealer.

DON’Tremove any fixed cover as this may expose

dangerous voltages.

DON’Tleave equipment switched on when it is

unattended unless it is specifically stated that

it is designed for unattended operation or has

a standby mode. Switch off using the switch

on the equipment and make sure that your

family knows how to do this. Special

arrangements may need to be made for infirm

or handicapped people.

NOTES:

●The rating plate (serial number plate) and

safety caution are on the bottom of the

VIDEO CAPTURE DOCKING STATION.

●The rating plate (serial number plate) of the

AC Power Adapter/Charger is on its bottom.

This unit is produced to comply with Standard

IEC Publ. 65.

DON’Tuse equipment such as personal stereos or

radios so that you are distracted from the

requirements of road safety. It is illegal to

watch television whilst driving.

DON’Tlisten to headphones at high volume, as such

use can permanently damage your hearing.

DON’Tobstruct the ventilation of the equipment, for

example with curtains or soft furnishings.

Overheating will cause damage and shorten

the life of the equipment.

DON’Tuse makeshift stands and NEVER fix legs with

wood screws — to ensure complete safety

always fit the manufacturer’s approved stand

or legs with the fixings provided according to

the instructions.

DON’Tallow electrical equipment to be exposed to

rain or moisture.

ABOVE ALL

— NEVER let anyone especially children push anything

into holes, slots or any other opening in the case —

this could result in a fatal electrical shock;

— NEVER guess or take chances with electrical equip-

ment of any kind — it is better to be safe than sorry!

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTIONS

DO NOT attempt to insert foreign objects into the connectors, as this can lead

to electric shock or fire. If an object is accidentally inserted, unplug it and

contact your JVC dealer. Be especially careful with children.

If during use you notice that the VIDEO CAPTURE DOCKING STATION is

damaged, unplug it and contact your JVC dealer. Use of the VIDEO CAPTURE

DOCKING STATION under these conditions can lead to fire or electric shock.

DO NOT attempt to repair or modify the VIDEO CAPTURE DOCKING

STATION. Doing so may result in malfunctions or injury. If a problem occurs,

contact your JVC dealer.

Failure to heed the following precautions may result in damage to the VIDEO

CAPTURE DOCKING STATION.

1. DO NOT place the VIDEO CAPTURE DOCKING STATION . . .

.... in an environment prone to extreme temperatures or humidity.

.... in direct sunlight.

.... in a dusty environment.

.... in an environment where strong magnetic fields are generated.

.... on a surface that is unstable or subject to vibration. The unit may fall, causing injury.

2. DO NOT place heavy objects on the VIDEO CAPTURE DOCKING STATION.

3. DO NOT place anything which might spill on top of the VIDEO CAPTURE DOCKING

STATION.

4. AVOID violent shocks to the VIDEO CAPTURE DOCKING STATION during transport.

5. DO NOT leave the VIDEO CAPTURE DOCKING STATION plugged in when the unit is not

in use.

6. DO NOT use accessories other than those designated in the instructions. Use of others can

lead to fire or electric shock.

7. DO NOT connect devices to the VIDEO CAPTURE DOCKING STATION other than those

designated in the instructions. Use of others can lead to malfunctions.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to handle a CD-ROM

● Take care not to soil or scratch the mirror surface (opposite to the printed surface). Do not

write anything or put a sticker on either the front or back surface. If the CD-ROM gets dirty,

gently wipe it with a soft cloth outward from the center hole using a circular motion.

● Do not use conventional disc cleaners or cleaning spray.

● Do not bend the CD-ROM or touch its mirror surface.

● Do not store your CD-ROM in a dusty, hot or humid environment. Keep it away from direct

sunlight.

MAINTENANCE

If the inside of the VIDEO CAPTURE DOCKING STATION is left dusty for a long time, its use

can lead to fire or malfunction. Consult your JVC dealer on cleaning.

AC Power Adapter/Charger

● DO NOT remove the cover and attempt to repair or modify the AC Power Adapter/Charger.

Doing so may result in malfuncitons or electrical shock and injury. If a problem occurs,

contact your JVC dealer.

● Make sure the Power Cord is securely connected to the AC Power Adapter/Charger.

● When using the AC Power Adapter/Charger, use only the supplied Power Cord. Use of any

other cord may result in shock or fire.

● Connect the Power Cord to the AC Power Adapter/Charger before connecting it to an AC

outlet. If you plug it into an outlet first, and the Adapter’s terminals come in contact with a

metal surface or object, short circuit or fire may result.

● Vibration noise can sometimes be heard coming from the inside of the AC Power Adapter/

Charger. This is normal.

● The AC Power Adapter/Charger processes electricity internally, and will become warm

during use. This is normal. Make sure to use the AC Power Adapter/Charger in well-

ventilated areas only.

CAUTION:

Changes or modifications not approved by JVC could void user’s authority to operate the

equipment.

● The Readme.TXT file provides additional information for setup and information that is not

included in the instruction manual. Please read the file before installing the provided

software program.

● You can find the latest information (in English) on the provided software program at our

www server.

<www>http://ww w .jvc-victor.co.jp/

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

MAJOR FEATURES

CONTROLS AND CONNECTORS

CONNECTIONS (When Using JLIP Video Capture Software) 12

INTRODUCTION

INSTALLATION (JLIP Video Capture Software)

HOW TO OPEN THE PROGRAM

Preparation ................................................................... 16

INITIALIZATION 17

Initializing JLIP .............................................................. 17

Select units.................................................................... 18

HOW TO CLOSE THE PROGRAM

HOW THE DESKTOP WORKS

Main desktop window....................................................... 20

Menu bar ...................................................................... 21

VIDEO CAPTURE

Capturing video images ..................................................... 24

Step by step capture......................................................... 25

Automatic capture............................................................ 26

Program capture ............................................................. 26

Interval capture .............................................................. 28

SAVE PICTURE

Saving ......................................................................... 29

Save the full image data .................................................... 29

PICTURE FORMAT SETTING

Selecting a picture format................................................... 30

Delete index image and full image......................................... 31

Change ID ..................................................................... 31

ADDITIONAL OPERATIONS

Counter value change ........................................................ 32

Counter reset ................................................................. 32

Open index.................................................................... 33

Create new folder ............................................................ 33

Download from Www.Somanuals.com. All Manuals Search And Download.

JLIP PLAYER SOFTWARE

Using JLIP player software data........................................... 34

How to store JLIP player software data ................................. 35

TROUBLESHOOTING

LIST OF ERROR MESSAGES

JLIP PLAYER SOFTWARE SECTION

CONNECTIONS (When Using JLIP Player Software)

When connecting to a video source unit with JLIP connector or to a

video printer................................................................ 42

GETTING STARTED

INSTALLING (JLIP Player Software)

STARTING JLIP PLAYER SOFTWARE

MOVIE PLAYER WINDOW BUTTONS AND DISPLAYS 48

BASIC OPERATIONS

VIDEO PRINTER WINDOW BUTTONS AND DISPLAYS

VIDEO PRINTER OPERATION (GV-PT2)

Printing ........................................................................ 58

Auto capture .................................................................. 60

ADVANCED OPERATIONS

Changing ID number ......................................................... 62

Connecting other device during operation................................. 62

Changing the name of the device........................................... 63

Changing the device to use while connecting over

two same type devices ................................................... 63

Adjusting the gap between the stored edit-start point in the

computer and the dubbed one in the recording deck .................. 64

TROUBLESHOOTING

MAJOR SPECIFICATIONS

INDEX

Download from Www.Somanuals.com. All Manuals Search And Download.

MAJOR FEATURES

Advanced Applications

Create title indexes for your video

collection

Title index images can be captured from your

favorite recordings in intervals of 30 minutes,

1 hour, 1.5 hours, etc. using the Interval

Capture mode. Print the captured index

images on your PC printer using the compu-

ter's Print Screen facility, then attach them to

your cassettes.

Business presentations

Images captured from video can be incorpo-

rated into business documents to spice up

your presentations.

Internet homepage

Images captured from video can be incorpo-

rated in your Internet homepage using image

editing software.

Video journal and postcards

Create your own original postcards, party

invitation cards and the like or keep a video

journal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Two software programs are provided with the GV-DS1 JLIP package.

JLIP Player Software

JLIP Video Capture Software

(੬ pg. 41 – 65)

(੬ pg. 12 – 39)

JLIP Control Facility

With a JLIP-compatible camcorder, VCR or

video printer (GV-PT2):

JLIP Video Capture Software

This is the software described in this manual.

• all basic video operations can be

executed on the computer display;

• allows programmed video playback (up

to 99 programmes) or assemble editing

• print command can be issued to the GV-

PT2 video printer

Video Capture Facility

Video images from video source units such as

camcorders or VCRs can be captured as 768

x 552 still images with 16.77 million colours

through the serial port (RS-232C) of a

Windowsா-operated computer.

Data Sharing with the Video Capture

Software

JLIP Control Facility

With a JLIP compatible camcorder or VCR,

• all basic video operations can be

executed via the computer display;

• Up to 99 images can be captured

automatically with Program Video

Capture (playing tape — scanning —

transferring to PC)

Video Capture Software data can be exported

to the Player Software.

Assemble Editing

Selected scenes on a pre-recorded tape can

be edited in a specified sequence.

Data Sharing With JLIP Player Soft-

ware

Data can be imported from the JLIP Player

Software.

Data from the Video Capture Software can

also be exported to the Player Software for

Program Playback or Assemble Editing.

Pre-recorded tape

(on camcorder)

Recording tape

(on VCR)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLS AND CONNECTORS

The controls and connectors marked can be used only when the GR-DVM1 Digital

Camcorder is attached. For details of its operation, read the camcorder instruction manual.

* Stop button

* Play button

* Pause button

* Edit start button

* Rewind button

* Fast forward button

* Lock lever

* Unlock button

* Digital jack ੬ p. 13

•Connect to the computer’s

RS-232C terminal (COM

port).

JLIP jack ੬ p. 13

* MULTI connector

(JLIP: Joint Level Interface Protocol)

•Connect to a JLIP-compatible

comcorder or VCR to control it

from the computer.

•The Docking Station can be connected with

the GR-DVM1 through this connector.

Never touch it with your hand or hit it with

a hard object; if the pins are damaged, the

connectors will become unusable due to

contact failure.

Download from Www.Somanuals.com. All Manuals Search And Download.

* DC output jack

•For dealer use.

* S2 (Video) output jack

•Outputs the S-VIDEO signal.

(Also compatible with S1 and S2

connectors.)

DC input jack ੬ p. 13

* Video output jack

* Remote control sensor

* Audio output jack (Left)

* Audio output jack (Right)

•Receives the remote

control signals for the

attached Camcorder.

* Edit jack

Capture input (EXT.)/printer connector

•Connect with the video output (stored image output) of the optional video printer. Even

when a TV is not connected to the video printer, this connection allows you to see the

images output from the video printer on the LCD screen while printing.

•The date and timecode are not shown on the LCD screen. If you want to print out the date

together with the images, connect a TV to the video output connector of the video printer

and operate it by referring to the TV screen.

•It is also possible to capture images from video equipment other than the GR-DVM1 by

connecting the equipment to this connector. To make this operation possible, also attach

the GR-DVM1 and set its power switch to record mode without loading a tape.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS (When Using JLIP Video Capture Software)

Ⅲ To assure safety, make sure all units are turned off before making any connections.

Ⅲ The video images will be displayed on the LCD screen of the attached GR-DVM1. You

cannot view the images on the computer screen.

Ⅲ When connecting the provided cables, be sure to connect the terminals equipped with Core

filters to the Video Capture Docking Station.

Ⅲ When using the Video Capture Docking Station, use the AA-V80EK/EA AC Adapter/Charger

(provided with the camcorder).

To Digital (8-pin)

connector

Core filter

PC connection cable

(provided)

To COM

(RS-232C) port

Personal computer

Image sources with JLIP and video output connectors

VCR (Recording deck)

(red) (white) (yellow)

To JLIP jack

To VIDEO output jack

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital

Camcorder

AC Adapter/Charger

Video Capture

Docking Station

To DC

output

jack

JLIP

DC cable (provided)

Core filter

To JLIP

jack

Core

filter

(red) (white) (yellow)

To CAPTURE

INPUT

(EXT.)/

PRINTER

connector

Core filter

3.5 mm diameter 4-pole

cables (provided)

Other units

with video

output jack

AUDIO/VIDEO cable

(provided)

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

What is video capture software ?

Video capture software is a type of application program that allows you to capture video

images from camcorders and VCRs and store them in personal computers running under the

Windowsா operating system. These images can be transferred from the video source to the

computer via a standard RS-232C communication interface. By processing the captured

images with commercially available image editing software, you can create your own unique

and highly personal illustrations and graphics for incorporation into everything from postcards

to newsletters and Internet homepages. What’s more, you can also use your computer to edit

your original video recording and produce a fun-to-watch, professional-looking video pro-

gramme.

What is JLIP ?

JLIP* stands for Joint Level Interface Protocol, a new communication protocol which allows AV

units equipped with a JLIP terminal to be controlled by a personal computer.

is a registered trademark of JVC.

Operating Environment

● Personal computer with Microsoftா Windowsா 3.1 or Windowsா 95

● CPU Intel DX4™ or higher processor

● Minimum RAM requirement: more than 8 MB

● Available Hard Disk space of at least 8 MB

● Colour display capable of at least 640 x 480 pixels, 256 colours

Recommended 1024 x 768, 16.77 Mil colours

● 1 free serial transmission port, compatible with 9600 bps transmission rate, connectable to

RS-232C with 9 pin serial connector.

Recommended compatible with UART 16550A

● Mouse (Windowsா compatible)

● CD-ROM drive

Note : An optional 9 pin serial conversion adapter is required for computers using serial

communication port other than standard 9 pin.

* Microsoftா and Windowsா are either registered trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

* Other product and company names included in this instruction manual are trademarks and/or registered

trademarks of their respective holders.

Connectable Devices

When using JLIP with Video units equipped with a JLIP connector :

● Camcorders GR-DV1, GR-DVJ70, GR-DVM1 etc (A junction box with a JLIP terminal is

required for connection to GR-DV1, GR-DVJ70 and GR-DVM1.)

When not using JLIP:

● Video units with video output connectors

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (JLIP Video Capture Software)

WINDOWSா 95

WINDOWSா 3.1

Refer to the Windowsா 95 manual or your

computer’s manual for details on basic

Windowsா 95 operating procedures.

Refer to the Windowsா 3.1 manual of or your

computer manual for details on basic

Windowsா 3.1 operating procedures.

Installation Procedure

This software offers you the choise of viewing

on-screen messages in English or French.

Select the desired language during installa-

tion by performing the following steps.

This software offers you the choise of viewing

on-screen messages in English or French.

Select the desired language during installa-

tion by performing the following steps.

*To start the setup program...

Launch Windowsா 95

Launch Windowsா 3.1

1 _{•Close any other applications that are}1 _{•Close any other applications that are}

running.

Insert the "JLIP Video Capture" CD-ROM

2 _{into the CD-ROM drive.}

Choose "Run" from "Start" on the taskbar.

Choose "Run" from "File" in the "Program

3 _Manager".

If you want English on-screen mes-

4 _sages…

If you want English on-screen mes-

4 _sages…

If the "JLIP Video Capture" CD-ROM is in

Drive D, type "D:\JCPTE\SETUP" in the

box to the right of "Name". If the disk is

in Drive E, type "E:\JCPTE\SETUP".

If the "JLIP Video Capture" CD-ROM is in

Drive D, type "D:\JCPTE\SETUP" in the

box to the right of "Name". If the disk is

in Drive E, type "E:\JCPTE\SETUP".

If you want French on-screen mes-

sages…

If the "JLIP Video Capture" CD-ROM is in

Drive D, type "D:\JCPTF\SETUP" in the

box to the right of "Name". If the disk is

in Drive E, type "E:\JCPTF\SETUP".

If you want French on-screen mes-

sages…

If the "JLIP Video Capture" CD-ROM is in

Drive D, type "D:\JCPTF\SETUP" in the

box to the right of "Name". If the disk is

in Drive E, type "E:\JCPTF\SETUP".

•Click "OK".

•Once the setup program is running,

simply follow the instructions displayed

on-screen.

•Once the setup program is running,

simply follow the instructions displayed

on-screen.

•When setup is complete, the "JLIP

Video Capture" icon appears on the

screen.

•"JLIP Video Capture Setup was com-

pleted successfully." appears.

•When setup is complete, the "JLIP

Video Capture" icon appears on the

screen.

•"JLIP Video Capture Setup was com-

pleted successfully." appears.

Click "OK" to complete installation.

NOTE : This instruction manual uses

English on-screen messages in its

explanation.

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO OPEN THE PROGRAM

The Video Capture software can be started up in the same way as any other program running

under Windows. The procedure differs slightly depending on whether you’re using Windowsா

3.1 or Windowsா 95.

Preparation

• Turn on your computer.

• Turn on the video source units (such as camcorders and VCRs).

• If you want to capture a still picture from a recorded tape, load the tape into the video unit.

• If you want to capture an image from the data stored in the JLIP Player Software, be sure to

load the disk on which the image is stored.

Close any programs that are running. You cannot run other programs simultaneously with

the Video Capture software.

With Windowsா 3.1, open the group of application icons in the Program Manager and

double-click the application icon you want to launch.

With Windowsா 95, click the [START] button on the taskbar, and the Program menu

appears on the screen. Move the mouse pointer over the program entry you want to run

and click to start the program.

Now let’s start the program.

If you’re using Windowsா 3.1, open the JLIP Video Capture group in the "Program Manager" and

double-click the JLIP Video Capture icon.

If you’re using Windowsா 95, select JLIP Video Capture from the "Start menu" and click to start.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIALIZATION

INITIALIZING JLIP

The first time you start the Video Capture software, JLIP initialization is required. This sets which

of the computer’s COM ports (connector into which the RS-232C cable is plugged) is connected

to the GV-DS1 JLIP Video Capture Docking Station. The initialization window automatically

appears the first time you start the software after installation. Do not forget to carry out this JLIP

initialization procedure. The JLIP must be initialized again whenever you connect a new image

source or other unit to the JLIP Video Capture Docking Station.

1. Start the JLIP Video Capture software.

2. The "JLIP Initialization" screen automatically appears.

3. Select "COM Port".

•COM1 through COM4 ports are available. Check to see which COM port is connected to

the JLIP Video Capture Docking Station and select it.

4. Select "Transfer Rate".

•Normally select 38400.

•38400 may not be available on some computers. When transmission errors take place

during use, switch to 19200 or 9600. Image data transmission will be slower at these

speeds.

5. Click "OK" . Call up the "JLIP Initialization" window and check the connected units.

JLIP Initialization

COM Port COM 1

Transfer Rate 38400

Cancel

NOTE : If you want to change a unit or COM port or Transfer Rate, select "Initialize" from

"Set-up" in the menu bar to call up the "JLIP Initialization" window. Repeat this

setting procedure.

If a connection is incorrect, a connected unit is not turned on, or the connection ID numbers

overlap, the message "Connection error" appears. Click "OK" to return to the Main desktop.

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECT UNITS

6. Call up the "Device Selection" window.

7. Click the name of the unit required.

•The word "VCRCAMERA" appears in the VCR box to indicate the Video source unit is now

in use.

•The word "MODULE" appears in the Video Capture box to indicate the Video Capture

Docking Station is now in use.

•Only one VCR and one Video Capture device can be selected.

8. Click "OK".

•The main desktop window returns (setting complete).

Device Selection

VCR

Not connected

06:VCRCAMERA

Cancel

Video Capture

Not connected

83:MODULE

NOTE : The "Device Selection" window automatically appears when JLIP initialization is

complete. However, if you want to select equipment whose JLIP initialization has

already been carried out, select "Device Change" from "Set-up" in the menu bar to

call up the "Device Selection" window.

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO CLOSE THE PROGRAM

Double-click the control menu button in Windowsா 3.1 or click "Exit" in the "File (F)" menu.

In Windowsா 95, simply click the Close button.

If you try to close the programme with no

File

image data saved, the message "The album

New Album

Open Album

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

has not been saved. Save?" appears. Please

note that if you close without saving, all

unsaved captured data will be deleted.

Ctrl+S

Ctrl+A

Save Image As…

Exit

Click "Exit" from "File" in the menu bar.

•The programme closes.

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW THE DESKTOP WORKS

MAIN DESKTOP WINDOW

Menu bar

Control

buttons

Image display area

JLIP Video Capture [–Untitled Folder–] (Untitled)

File Edit Set-up Window Help

button

CAPTURE

TRANSFER

INPUT

MEMORY

JLIP

00:01:23:12 00:02:17:21 00:07:01:19 00:37:05:06 00:20:39:18

06 07 08

00:39:03:11 00:47:53:03 --:--:--:--

Menu bar

Displays function menus. See the next page for detailed information.

Control buttons

•CAPTURE button (੬ pages 25)

Press to CAPTURE a desired image from an image source. When pressed, an index

image appears under this button.

•TRANSFER button (੬ pages 27, 28)

The TRANSFER button is used to start Automatic Transfer. Automatic Transfer is divided

into Program Capture and Interval Capture.

•MEMORY/INPUT button

Press to switch between the image stored in this unit and the image from the video

source.

•JLIP button (੬ pages 41 through 65)

The JLIP Video Capture software and JLIP Player software cannot run simultaneously.

When you want to run the JLIP Player software, press this button to call up a cross bar

and run the software. To resume using the JLIP Video Capture software, first select "Close

Serial" from "File" on the JLIP Player Software's menu bar, then press the JLIP button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Image display area

Each time you press the Capture button an index image is captured into the image area.

Up to 99 images can be captured, with up to five images in one horizontal frame. Index

images are provided to allow you to confirm that you have captured the images you want.

Index image data: 80 x 60 pixels Full image data: 768 x 552 pixels

Image display box

Click to select an image display box, and

•the border turns green

•Double-click an image display box, and Full

image data will appear if it has already been

transferred

Index numbers are

automatically assigned

00:02:17:21 00:07:01:19 00:37:05:06

Colours of counter numerals

Hatched like this when

Counter display

Black : Full image data transferred counter time is corrected

Indicates the current tape position

eg. 00 : 12 : 17 : 21

Hour : Min : Sec : Frame

White: Full image data not

transferred (only index

image data transferred)

(੬ p. 32)

MENU BAR

All program functions can be selected from the menus in the menu bar. Click any item in the

menu bar to open the corresponding pulldown menu. Then click the desired command in the

pulldown menu. Some menu entries are invalid depending on the program status. Invalid

commands appear lighter than valid commands.

JLIP Video Capture

File Edit Set-up Window Help

New Album

Open Album

MEMORY

INPUT

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

Ctrl+S

Ctrl+A

Save Image As…

Exit

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW THE DESKTOP WORKS (cont.)

Each pulldown menu is configured as follows

File

New Album

Open Album

Erases the image currently on screen and creates a new image.

Opens an index file (੬ p. 33).

Stores the index image on screen (੬ p. 29).

Opens a JLIP Player software file (੬ p. 34) .

Converts to and saves as a JLIP Player software file (੬ p. 35).

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

Ctrl+S

Ctrl+A

Saves the image data file to another folder or drive (੬ p. 29).

Closes the program (੬ p. 19).

Save Image As…

Exit

•An index image of the image data in the Video Capture Docking

Station memory is transferred to your computer and displayed in

the selected image box (in the Step by Step capture mode).

•The video source unit scans the selected counter value and

transfers the index image to your computer (in the automatic

capture mode) (੬ p. 32).

•A full image of the image data in the Video Capture Docking

Station memory is transferred to your computer (in the Step by

Step capture mode).

Edit

Transfer the Index Image

Transfer the Full Image

Modify…

Delete

Del

•The video source unit scans the selected counter value and

transfers the full image data (768 x 552 pixels) to your computer

(in the automatic capture mode) (੬ p. 32).

Changes the scan timing in the automatic capture mode by chang-

ing the counter preset (੬ p. 32).

Deletes the index image (੬ p. 31).

Two different modes available: Step by Step Capture and Automatic Capture

(੬ p. 25, 26, 28).

Set-up

Selects image data format to be used in the transfer and capture mode

(੬ p. 30).

To initialize a connected unit or to change a connected unit (੬ p. 18).

Initialize when changing a COM port or transfer rate (੬ p. 17).

Changes the Video Capture unit’s ID number (੬ p. 31).

Resets the VCR's counter (੬ p. 32).

Capture Mode

Image Format

Device Change

Initialize

ID Change

Counter Reset

Download from Www.Somanuals.com. All Manuals Search And Download.

Window

Deletes space when an index image has been deleted (੬ p. 31).

The VCR operation window appears to allow the computer to operate

the VCR.

Arrange Index

VCR

[VCR] operation window

VCR POWER button

Counter display

VCR

00:01:23:12F

FF/FF Search

button

Reverse Slow button

Capture button

Capture

Transfer

Transfer button

Forward Slow

button

PAUSE

button

REW/REW Search

button

PLAY

button

STOP

button

VCR models operable on the VCR Operation Window (compatible with JLIP)

Help

Contents

Display Help menu

About JLIP Video Capture

Display version information of this software.

NOTE : Counter reset

If you use a DV-format digital camcorder, counter information is represented by the

time code written on the tape. Counter reset is not possible.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CAPTURE

CAPTURING VIDEO IMAGES

There are three capture modes available: Step by Step, Program and Interval. The latter two

modes are available only when connected to a JLIP compatible video source unit. Step by Step

Capture mode must be used to capture images from a video source unit with no JLIP connector.

Image data flow

Video signal

GV-DS1

(Image stored in video memory)

Video source

unit

Full image data

(with a resolution of 768 x 552

pixels)

Index image data

(with a resolution of

80 x 60 pixels)

2 types of video data

•Bitmap data Approx. 1.3MB

•JPEG video compression data

Approx. 50 kB

(video data are stored on a hard disk or the like)

When storing full image data on a 2HD disk,

• An image saved in the bitmap data format can be stored on one disk.

• About 28 images saved in the JPEG video compression format can be stored on one disk.

This is the case when using floppy disks formatted for 1.44 MB.

NOTES:

•The index image is displayed in the

image display box.

•Each time the image display box is

double-clicked, the full image data (768

x 552 pixels) is displayed only after full

image data transfer is finished.

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP BY STEP CAPTURE

Use the Step by Step Capture mode when you want to:

•Capture images from a video source unit with no JLIP connector

•Capture images from video units with video output connectors

•Capture a smaller number of images

•Confirm the images being captured.

Preparation

•Make sure all units are properly connected

(੬ p. 12).

Set-up

Step by Step

Automatic

•Click "Image Format" in "Set-up" and select

the desired format (੬ p. 30).

Capture Mode

Image Format

Device Change

Initialize

ID Change

Counter Reset

Open the menu bar and click "Set-up" —

1 _{"Capture Mode" — "Step by Step".}

•The Step by Step Mode is entered.

Click "CAPTURE" on the image you want

2 _{to capture.}

•When a JLIP-compatible video source

unit is connected, click "Window" —

"VCR" to have the VCR scan the picture

in the VCR Operate window (੬ p. 23).

•When you press the CAPTURE button,

full image data (768 x 552 pixels) is

captured into the Video Capture

JLIP Video Capture

File Edit Set-up Window

CAPTURE

TRANSFER

Docking Station memory. Index image

data (80 x 60 pixels) is simultaneously

transferred to the computer.

Index image data is transferred to the

3 _computer.

•The message "No.1 index image being

transferred." appears during data

transfer.

The message "Transfer the full image ?

4 _{Yes/No" appears. Click "Yes". Full image}

data (768 x 552 pixels) is transferred to

the computer.

•You cannot use the TRANSFER button

NOTES:

in Step by Step Transfer mode.

•Index image /Full image data are

transferred to the image display boxes

bordered in green. Click and select the

desired box(es).

•When transferring full image data using

the Bitmap image format ( .bmp), the

transfer takes a very long time, causing

the video source unit to stop playback

automatically.

The full image data is transferred to the

5 _computer.

•The message "No.1 full image being

transferred." appears during data

transfer.

Repeat steps 2 through 5 as required.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CAPTURE (cont.)

AUTOMATIC CAPTURE

Automatic video capture is available only when a JLIP-compatible video source unit is con-

nected. There are two types of automatic capture: Program mode and Interval mode. You can

save time in either mode because, once the initial settings have been stored or you have decided

what pictures to capture, the subsequent capture process is carried out automatically.

PROGRAM CAPTURE

In the Program Capture mode, select the images you want to capture, and the JLIP Video

Capture Docking Station will automatically capture and transfer the images to your computer.

Preparation

•Make sure all units are properly connected

(੬ p. 12).

•Insert a tape into the video source unit.

Click "Image Format" in "Set-up" and select

"Field Picture" in the Capture Mode

(੬ p. 30).

Open the menu bar and click "Setup" —

Set-up

1 _{"Capture Mode" — "Automatic".}

Step by Step

Automatic

Capture Mode

Image Format

Device Change

Initialize

ID Change

Counter Reset

•The "Automatic Transfer" window

appears.

Select data to be transferred.

2 _{•When you select "Index Image", index}

image data (80 x 60 pixels) is trans-

ferred to your computer.

•When you select "Index & Full Image",

both the index image data (80 x 60

pixels) and full image data (768 x 552

pixels) are transferred to the computer.

Select "Program Capture" and click

3 _"OK".

NOTES:

•Before transferring your images, make

sure that enough space is available on

your hard disk. For full image data

space requirements, ੬ p. 24.

•When transferring full image data using

the Bitmap image format ( .bmp), the

transfer takes a very long time, causing

the video source unit to stop playback

automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click "Window" — "VCR" to call up the

4 _{VCR Operation window.}

VCR

Operate the video source unit via the

5 _{VCR Operation window.}

00:01:23:12F

Click the "Capture" button on the desired

6 _{video image, and index image data (80 x}

60 pixels) is transferred to the computer.

Capture

Transfer

•The message "No.1 index image being

transferred." appears during data

transmission.

Repeat steps 5 and 6 as necessary.

Click "Transfer" button.

8 _{•If you want to capture full image data}

(768 x 552 pixels) after capturing the

"Index Image" in step 2, click "Index &

Full Image" and then click the "Trans-

fer" button.

1. The message "Index No.1 being

scanned" appears while the video

source unit is scanning the picture to

be captured.

2. The message "No.1 index image being

transferred." appears and then "No.1

full image being transferred." appears

while the full image data is being

transferred to the computer.

3. The images captured in step 7 are

scanned by the video source unit and

automatically transferred to the

computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CAPTURE (cont.)

INTERVAL CAPTURE

Preparation

•Make sure all units are properly connected

(੬ p. 12).

The Interval Capture mode is best suited for

capturing images at set intervals from a video

source unit with a JLIP connector.

•Insert a tape into the video source unit.

Click "Image Format" in "Set-up" and select

"Field Picture" in the Capture Mode.

(੬ p. 30).

Open the menu bar and click "Set-up" —

"Capture Mode" — "Automatic".

Set-up

•The "Automatic Transfer" window

appears.

Step by Step

Automatic

Capture Mode

Image Format

Device Change

Initialize

ID Change

Counter Reset

Select the data to be transferred.

2 _{•When you select "Index Image", index}

image data (80 x 60 pixels) is transferred

to your computer.

•When you select "Index & Full Image",

both index image data (80 x 60 pixels)

and full image data (768 x 552 pixels) are

transferred to the computer.

Select "Interval Capture".

Set the interval.

4 _{•Select the time interval at which pictures}

VCR

are captured.

Set the number of pictures to be captured

00:01:23:12F

and click "OK".

•From 1 up to 99

Capture

Transfer

Click "Window" — "VCR" to call up the

VCR Operation Window. Start video

playback a few seconds prior to the point

where you want image capturing to start.

Operate the video source unit via the VCR

Operation window and click the "Transfer"

button at the desired picture.

1. The message "No. 1 index image being

transferred." appears while the index image

data is being transferred to the computer.

2. When you select "Index & Full Image" in

step 2, the message "No. 1 full image being

transferred." appears while the full image

data is being transferred to the computer.

3. The message "Index No. 2 being scanned."

appears while the video data are fast-

forwarded and played at the time intervals

set in step 4 to scan the video data on the

VCR.

NOTES:

•Make sure that enough hard disk space is

available on your computer before

executing video transfer.

For full image data space requirements,

੬ p. 24.

•Transfer of index image data/full image

data starts at the image box bordered in

green.

Click and select the desired image box.

•When transferring full image data using

the Bitmap image format ( .bmp), the

transfer takes a very long time, causing

the video source unit to stop playback

automatically.

• The image selected when "Transfer" is

clicked is captured and subsequent images

are captured at the time interval specified

by the counter value selected in step 4.

• The video source unit enters the Pause

mode when capture is complete.

Download from Www.Somanuals.com. All Manuals Search And Download.

SAVE PICTURE

SAVING

Select when storing the contents displayed in the image display area (page 21).

File

Open the menu bar and click "File" —

New Album

Open Album

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

1 _{"Save Album" .}

Ctrl+S

Ctrl+A

•The "Save Album" window appears.

Type the folder name and title.

2 _{•You can save without entering any title.}

Save Image As…

Exit

Click "OK".

3 _{•The file is saved.}

Enter title name

Enter folder name

Save Album

Folder: c:\capture\index001

Title: (Untitled)

c:\

capture

Cancel

Select directory

Select drive

SAVE THE FULL IMAGE DATA

You can save a file under another name or in another folder so that you can edit it without

losing the original.

By processing the captured images with commercially available image editing software, you

can create your own unique and highly personal illustrations and graphics for incorporation

into everything from postcards to newsletters and Internet homepages.

File

Click the image display box of the Index

New Album

Open Album

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

1 _{No. to be saved.}

•The image display box is framed in

green.

Ctrl+S

Ctrl+A

Click "File" — "Save Image As…" on the

2 _{menu bar.}

Save Image As…

Exit

•The "Save Image As… (Index No. )"

window appears.

Click the name of the desired folder

3 _{(directory) in the Select Directory box}

and enter the file name.

NOTES:

•It is not possible to change the image

format when saving the full image data.

•If the full image data has not been

transferred to the computer, it is not

possible to save it. First transfer the full

image data, then save it.

•When saving the data to floppy disk,

enter the drive name as well.

Click "OK".

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE FORMAT SETTING

SELECTING A PICTURE FORMAT

Under "Image Format", you can specify the full image data format and the capture mode.

Set-up

Open the menu bar

1 _{and click "Set-up"}

— "Image Format".

Select capture mode.

3 _{•There are two different settings avail-}

Capture Mode

Image Format

Device Change

Initialize

ID Change

Counter Reset

able: "Frame Picture" and "Field

Picture". Refer to "Capture Mode"

below for details.

•The "Image

Format" window

appears.

Click "OK".

4 _{•This completes picture format setting.}

Select format.

2 _{•There are two different settings avail-}

•This setting takes effect the next time

you use the capture function.

able: "JPEG (9. jpg)" and "Bitmap (9.

bmp)". Refer to "Picture Data Format"

below for details.

TRANSFER DATA

Full image data can be captured and transferred in two different formats.

Picture Data Format

● JPEG ( . jpg)

• This is the default setting. If you do not set Picture Format, image data is captured in this

format.

• JPEG (Joint Photographic Expert Group) is a leading standard defining the compression and

decompression of still color pictures.

• The quantity of transferred data appears smaller because the images are compressed. This

results in a shorter transfer time.

● Bitmap ( . bmp)

• Transfer time is longer when you use this format because there is no data compression. The

benefit is that picture quality is maintained with no deterioration.

• Bitmap is a data format representing characters and graphics with combinations of pixels.

Full image data resolution is 768 x 552 pixels with 16.77 million colours (24-bit colour).

Index image data resolution is 80 x 60 pixels with 16.77 million colours (24-bit colour).

Capture Mode

● Frame Picture

• This is the default setting. If you do not set Picture Format, images are captured in this

mode.

• Since a frame consists of two overlapping 1/50 sec. images (one 1/25 sec. image forms a

field), it is unstable when capturing fast-moving motion pictures.

● Field Picture

• While a field contains only half the data of a frame — meaning that vertical resolution is

half that of a frame — images captured from a fast-moving motion picture are more stable

than when captured with "Frame Picture".

Download from Www.Somanuals.com. All Manuals Search And Download.

DELETE INDEX IMAGE AND FULL IMAGE

You can delete any captured picture. Both index image (80 x 60 pixels) and full image (768 x

552 pixels) are deleted.

Click the image display box you want to

1 _delete.

•The box is bordered in green.

00:02:17:21

Open the menu bar and click "Edit" —

2 _"Delete".

•This deletes the selected image data.

Edit

Then click "Window" — "Arrange

3 _Index".

Transfer the Index Image

Transfer the Full Image

Modify…

Delete

•This removes the deleted index image’s

space and renumbers the remaining

index display box. You can still run the

program without re-arranging the

index.

Del

Window

Arrange Index

VCR

CHANGE ID

You can change the Video Capture Unit’s ID number.

Open the menu bar and click "Set-up" —

1 _{"ID Change".}

Set-up

•ID Change window appears.

Capture Mode

Image Format

Device Change

Initialize

ID Change

Counter Reset

Enter a new ID number.

Click "OK".

3 _{•This completes the ID number change.}

Open the menu bar and click "Set-up" —

4 _{"Initialize".}

•The "JLIP Initialization" window

appears.

•Start JLIP initialization. (੬ p. 17, 18).

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDITIONAL OPERATIONS

COUNTER VALUE CHANGE

If you want to replace a captured image with a different one, you can capture the new one by

changing the counter value.

Click the image display box of the index

1 _{number you want to change.}

•The box is bordered in green.

00:02:17:21

Open the menu bar and click "Edit" —

2 _"Modify…".

•The "Modify Capture Point" window

appears.

Edit

Enter a new counter value.

Transfer the Index Image

Transfer the Full Image

Modify…

Delete

Click "OK".

4 _{•The index image is surrounded by a}

Del

hatching pattern indicating that a

change is being made.

•The counter value is changed to the

value you just entered.

Open the menu bar and click "Set-up" —

5 _{"Capture Mode" — "Automatic", then}

select "Program Capture" in the "Auto-

matic Transfer" window and click "OK".

00:01:23:12

Play the tape on the video source unit

6 _{and click "Edit" — "Transfer the Index}

Image".

•Index image data at the counter setting

is captured.

00:01:23:12

•Be sure to complete steps 1 through 7.

If they are not all followed, the index

image and the full image will be

different as the full image data will not

have been changed in step 6.

NOTE : Note that if the index image data

is saved in step 4, the hatching

pattern indicating the change will

no longer appear the next time it

is called up.

Click "Edit" — "Transfer the Full Image".

7 _{•Full image data at the counter setting is}

transferred.

COUNTER RESET

You can change the counter setting on connected video source units (VHS, VHS-C).

Set-up

Open the menu bar and click "Set-up" —

1 _{"Counter Reset".}

Capture Mode

Image Format

Device Change

Initialize

•The VCR's counter is reset.

•The counters of DV-format digital

camcorders cannot be reset.

ID Change

Counter Reset

Download from Www.Somanuals.com. All Manuals Search And Download.

OPEN INDEX

File

Open the menu bar and click "File" —

1 _{"Open Album".}

New Album

Open Album

Save Album

•The "Open Album" window appears.

Ctrl+S

Ctrl+A

Open JLIP (jlp) File

Select the name of the folder (directory).

Save As JLIP (jlp) File

Save Image As…

Exit

Click "OK".

CREATE NEW FOLDER

Creating a new folder (directory) is a good idea when capturing an image from another video

tape.

File

New Album

Open Album

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

Open the menu bar and click "File" —

1 _{"New Album".}

•The image display area is refreshed.

•If the index image data on screen is not

saved, you will be asked whether to

save or not.

Ctrl+S

Ctrl+A

Save Image As…

Exit

Download from Www.Somanuals.com. All Manuals Search And Download.

JLIP PLAYER SOFTWARE

USING JLIP PLAYER SOFTWARE DATA

The GV-DS1 Video Capture Docking Station can capture JLIP Player software data at an edit-in

point corresponding to a preset counter number.

Preparation

•Make sure all units are properly connected

(੬ p. 12).

•Insert the tape program edited with the

Player Software into the video source unit.

•If the data is stored on a floppy disk, load

disk into the floppy disk drive.

Open the menu bar and click "File" —

File

New Album

Open Album

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

1 _{"Open JLIP (jlp) File".}

•The "Open JLIP(jlp) File" window is

displayed.

Ctrl+S

Ctrl+A

Double-click the name of the desired

2 _{folder (directory) in the Select Directory}

box.

Save Image As…

Exit

•If the data is stored on a floppy disk,

enter the drive name.

Click on the file name to select it.

Click "OK".

4 _{•The computer monitor displays Scene}

No., counter number at Edit-in Point,

and a blank image box.

Open the menu bar and click "Set-up" —

5 _{"Capture Mode" — "Automatic".}

Select the data you want to transfer and

6 _{"Program Capture" and click "OK".}

Click the "TRANSFER" button.

7 _{•The image data scanned by the video}

source unit is automatically transferred

to your computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO STORE JLIP PLAYER SOFTWARE DATA

Data from this unit can be converted to JLIP Player software files.

If index image data is saved as a JLIP Player software file, the file can be printed with the

optional GV-PT2 Video Printer.

Refer to the instruction manual for details.

Preparation

•Make sure all units are properly connected

(੬ p. 12).

•Insert a video tape into the video source

unit.

•If you want to store the data on a floppy

disk, load a data disk into the floppy disk

drive, create a directory and sub-directory

on the data disk (੬ p. 54).

Open the menu bar and click "File" —

1 _{"Save As JLIP (jlp) File".}

File

New Album

Open Album

•The "Save As JLIP (jlp) File" window is

displayed.

Save Album

Open JLIP (jlp) File

Save As JLIP (jlp) File

Ctrl+S

Ctrl+A

Enter the folder name (directory) and file

2 _name.

•If you want to store the data on a

floppy disk, enter the drive name.

Save Image As…

Exit

Click "OK".

3 _{•The data converted to a JLIP Player}

software file is stored on the floppy disk

in the selected drive.

•JLIP Player software files can be used

for video program editing or printed

with the video printer. (੬ p. 58, 60)

NOTE : When stored data is opened with

the JLIP Player software, the edit-in

and edit-out points have the same

counter value. When you want to

perform program editing, change

the counter number at the edit-out

point in the JLIP Player software’s

"Modify Edit Points".

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

NOTE : External noise or disturbance may interfere with the microprocessors built into the

GV-DS1 JLIP Video Capture Docking Station. If this happens, turn the power off and

then turn it on again.

Problem

Cause

Page

No effect when clicking the

Input Select/Memory

buttons.

ⅷ The windows do not change during transfer

or compression of index image/full image data.

ⅷ The video is displayed on the LCD screen of

the attached GR-DVM1. It is not possible to

check the images on the computer.

—

The video equipment image

is not displayed on the

connected TV.

ⅷ When video equipment is connected to the

CAPTURE EXT IN/PRINTER connector, its

video is displayed on the LCD screen of the

GR-DVM1.

—

The video unit does not

operate when "Window" —

"VCR" in the menu bar and

"VCR" in the "VCR" opera-

tion window are clicked.

ⅷ The counter display in the "VCR" operation

window turns blue.

ⅷ Is your video unit compatible with JLIP ?

Only JLIP-compatible units can be

operated.

If you are using a JLIP-compatible unit and

it still won’t work, check to make sure that

it is correctly connected.

10 – 13

ⅷ Is the video unit selected in "Select Unit" ?

Select correctly.

ⅷ Initialize JLIP.

ⅷ Make sure the video unit is turned on.

Reverse Slow Play and

Forward Slow Play not

available in "VCR" operation

window.

ⅷ These are available only when the video

—

unit has a Slow Play function.

The"VCR" operation

window display shows a

different operation from

what the video unit is

actually doing.

ⅷ Slow Play in the VCR operation window

automatically switches to Play after

approximately 20 seconds.

ⅷ In some cases, the video unit may continue

slow-motion playback even when the

"VCR" operation window changes from

Slow Play to Play. Check your video unit’s

instruction manual for details.

On-screen display of video

unit is stored in memory.

ⅷ If your video unit has an onscreen display,

—

turn it off.

Counter display appears in

the image display box even

when there is no tape in the

video unit.

ⅷ When capture video data from a powered-

on video unit with no tape loaded, a

counter display may appear in the image

display box. Images corresponding to the

displayed counter number can no longer be

caputred.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem

Cause

Page

Cannot capture video data

with the desired counter

number.

ⅷ There may be a slight difference between

the counter of the video image that you

want to capture and the Index image data/

Full image data captured in the computer.

This is not a malfunction.

25 – 28

Counter cannot be reset.

ⅷ Counter reset is not available with digital

camcorders.

Program capture suddenly

stops.

ⅷ When you start program capture at the

beginning of the tape, the video unit stops

playback, ending program capture.

—

Start video capture about 20 seconds after

the point where the recording begins.

After finishing video

capture, the video file

remains in the JCPT folder

(where the program run file

is contained).

ⅷ If you want to erase the file because of

limited hard disk space, start the program

once then close it. The video remaining in

the JCPT folder will be cleared.

JLIP initialization not

possible.

ⅷ Make sure that the IRQ (Interrupt ReQuest)

is not being used by another device.

ⅷ COM port selection is wrong. Confirm the

COM port number and execute JLIP

initialization again.

With Video capture/

Transfer done in Automatic

Transfer mode, the captured

image looks like two

pictures laid one upon

another.

ⅷ In this case, video capture is not possible

using the "Frame Picture" setting. Change

the setting to "Field Picture" and try video

capture again.

The monitor displays of the application software illustrated in this manual may differ from

those you are actually viewing depending on the operating environment of your computer.

Operation will be significantly slower when used in an environment other than that recom-

mended (page 14).

While basic VCR operations such as playback and fast-forward are available, a "transmis-

sion error" may occur in some models during video transfer. In this case, start the software

again, and turn the power of the Video Capture Docking Station off and on.

Download from Www.Somanuals.com. All Manuals Search And Download.

LIST OF ERROR MESSAGES

ⅷ Appears when:

Message

Page

Ⅵ Action:

COM port is not

available.

ⅷ Not connected to COM port set by JLIP Initialize.

Ⅵ Check the COM port number and connector and

retry JLIP initialization.

Connected device

not found.

ⅷ Connected devices are not turned on.

ⅷ Selected COM port is not connected properly.

Ⅵ Make sure connection is proper and carry out JLIP

initialization. Then turn on this unit and the

connected devices.

17,18

Error — Transfer

halted.

ⅷ Video unit is brought to STOP or ends playback

during automatic capture.

Ⅵ Check the auto capture setting.

ⅷ Full image data (768 x 552 pixels) cannot be

captured if you start auto capture at the beginning

of the tape. Video capture stops if video playback

is stopped.

—

Ⅵ Start video capture 20 seconds after the start of the

recording.

ⅷ Tape is too short to match the preset number of

images or there is a section of non-recorded tape.

Ⅵ Click "OK", check the tape length and re-enter the

number of images to be captured. Use a fully

recorded tape.

Download from Www.Somanuals.com. All Manuals Search And Download.

Page

ⅷ Appears when:

Ⅵ Action:

Message

Execute after

playing back the

VCR.

ⅷ Video unit is not in Play mode during Interval

Capture.

Ⅵ Click "OK", set the video unit to Play and click

"Transfer" again.

Not enough disk

space is available.

ⅷ Remaining disk space is under 1 MB.

Ⅵ Click "OK" , check disk space and select a drive

with space available with Store As.

—

Communication

error.

ⅷ If operation stops after this message appears, turn

the Capture Docking Station off and then on again.

Images stored in memory will be lost.

Ⅵ Do not use any other application while JLIP Video

Capture and JLIP player are running as it may

interfere with communication. Do not click and

move the mouse during data transfer.

ⅷ If your computer's energy saver, battery voltage

indication or screen saver is engaged, the image

data transmission may be interrupted.

Ⅵ Disengage these functions. Refer to your

computer's instructions manual on details.

Check the capture

device.

ⅷ If operation stops after this message appears, turn

the Capture Docking Station off and then on again.

Images stored in memory will be lost.

—

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

JLIP PLAYER SOFTWARE

SECTION

q The Readme.TXT file provides additional information for setup and information

that is not included in the instruction manual. Please read the file before installing

the provided software program.

q You can find the latest information (in English) on the provided software program

at our www server.

<www>http://www.jvc-victo r .co.jp/

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS (When Using JLIP Player Software)

WHEN CONNECTING TO A VIDEO SOURCE UNIT WITH JLIP

CONNECTOR OR TO A VIDEO PRINTER

Ⅲ Be sure to turn off the power of all connected units before making any connections.

Ⅲ When connecting the provided cable, be sure to connect the plug with the Core Filter to the

Video Capture Docking Station.

To digital

connector

(8 pin)

To COM port

(RS-232C)

Core

Filter

PC connection

cable (provided)

3.5 mm diameter

4-pole cable

(provided)

When connected with the Video Printer

GV-PT2 Video

Printer

Connect this if

the video unit

has an S-Video

input connector

To JLIP connector

S-Video

cable

To S-Video input connector

To video input connector

If you edit using a non-JVC VCR...

It is possible to use the remote control unit provided with the GR-DVM1.

Also refer to the GR-DVM1’s instructions on connection and operation

with your brand of VCR.

NOTE:

Some VCR brands or models cannot be operated.

RM-V708U or RM-V710U

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital camcorder

JLIP

JLIP Video Capture

Docking station

To edit jack

To JLIP

jack

Core Filter

AC Power

Adapter/Charger

(yellow) (white) (red)

To S

output

jack

To video/

audio output

jack

To DC

output jack

Core

Filter

cord

Core

Filter

Core

Filter

Connect this

if the video

unit has an

S input jack

EDIT cable

(provided)

AUDIO/

VIDEO

S-Video

cable

(provided)

cable

(provided)

AUDIO

input

To S-Video output jack

To video output jack

VIDEO

input

jack

To S-

VIDEO

input

jacks

Video cable

(L/R)

(red) (white) (yellow)

jack

VIDEO OUT

select switch

(Y/C or CVBS)

Cable adapter (provided only

with U.K. models)

If your VCR has the 21 pin AV

input connector (SCART), use

the provided cable adapter.

Connect to TV

Connect to AV jack-

equipped TV or to VCR

Connect

to TV

JVC Video unit

(Recording deck)

To remote

pause jack

Download from Www.Somanuals.com. All Manuals Search And Download.

GETTING STARTED

What is JLIP ?

JLIP* stands for Joint Level Interface Protocol, a new communication protocol which allows AV

units equipped with a JLIP terminal to be controlled by a personal computer.

is a registered trademark of JVC.

Operating Environment

● Personal computer with Microsoftா Windowsா 3.1 or Windowsா 95

● CPU Intel DX4™ or higher processor

● Minimum RAM requirement: more than 8 MB

● Available Hard Disk space of at least 8 MB

● Colour display capable of at least 640 x 480 pixels, 256 colours

Recommended 1024 x 768, 16.77 Mil colours

● 1 free serial transmission port, compatible with 9600 bps transmission rate, conneclable to

RS-232C with 9 pin serial connector.

Recommended compatible with UART 16550A

● Mouse (Windowsா compatible)

● CD-ROM drive

Note : An optional 9 pin serial conversion adapter is required for computers using serial

communication port other than standard 9 pin.

* Microsoftா and Windowsா are either registered trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

* Other product and company names included in this instruction manual are trademarks and/or registered

trademarks of their respective holders.

Devices to connect to the VIDEO CAPTURE DOCKING STATION

● Camcorder equipped with JLIP connector

● Video printer equipped with JLIP connector, GV-PT2 (as of March, 1997)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING (JLIP Player Software)

WINDOWSா 95

WINDOWSா 3.1

Refer to the Windowsா 95 manual or your

computer’s manual for details on basic

Windowsா 95 operating procedures.

Refer to the Windowsா 3.1 manual of or your

computer manual for details on basic

Windowsா 3.1 operating procedures.

Installation Procedure

This software offers you the choise of viewing

on-screen messages in English or French.

Select the desired language during installa-

tion by performing the following steps.

This software offers you the choise of viewing

on-screen messages in English or French.

Select the desired language during installa-

tion by performing the following steps.

*To start the setup program...

Launch Windowsா 95

Launch Windowsா 3.1

1 _{•Close any other applications that are}1 _{•Close any other applications that are}

running.

Insert the "VIDEO MOVIE PLAYER" CD-

2 _{ROM into the CD-ROM drive.}

Choose "Run" from the "Start" on the

Choose "Run" from "File" in the "Program

3 _taskbar.

3 _Manager".

If you want English on-screen messages…

4 _{If the "VIDEO MOVIE PLAYER" CD-ROM}4 _{If the "VIDEO MOVIE PLAYER" CD-ROM}

is in Drive D, type "D:\VMPE\SETUP" in

the box to the right of "Name". If the disk

is in Drive E, type "E:\VMPE\SETUP".

is in Drive D, type "D:\VMPE\SETUP" in

the box to the right of "Name". If the disk

is in Drive E, type "E:\VMPE\SETUP".

If you want French on-screen messages…

If the "VIDEO MOVIE PLAYER" CD-ROM

is in Drive D, type "D:\VMPF\SETUP" in

the box to the right of "Name". If the disk

is in Drive E, type "E:\VMPF\SETUP".

If you want French on-screen messages…

If the "VIDEO MOVIE PLAYER" CD-ROM

is in Drive D, type "D:\VMPF\SETUP" in

the box to the right of "Name". If the disk

is in Drive E, type "E:\VMPF\SETUP".

•Click "OK".

•Once the setup program is running,

simply follow the instructions displayed

on-screen.

•Once the setup program is running,

simply follow the instructions displayed

on-screen.

•When setup is complete, the "MOVIE

PLAYER" icon appears on the screen.

•"MOVIE PLAYER Setup was completed

successfully." appears.

•When setup is complete, the "MOVIE

PLAYER" icon appears on the screen.

•"MOVIE PLAYER Setup was completed

successfully." appears.

Click "OK" to complete installation.

NOTE : This instruction manual uses

English on-screen messages in its

explanation.

Download from Www.Somanuals.com. All Manuals Search And Download.

STARTING JLIP PLAYER SOFTWARE

Starting JLIP Player Software

PREPARE DEVICE(S)

Turn the device(s) on and set the

camcorder's Power Dial to "PLAY".

ACCESS MOVIE PLAYER

MOVIE

PLAYER

Double-click the MOVIE PLAYER icon

and the Serial Port Selection dialog box

appears.

SELECT SERIAL PORT

Select the port number of the connector

you are using to connect the computer to

the Video Capture Docking Station.

•If the connector number is A, B... A

corresponds to 1.

Serial Port Selection

Select a Serial Port.

COM 1

•Click "OK".

•If the connection is correct, the Device

Selection dialog box appears.

COM 2

COM 3

COM 4

CANCEL

Initializing JLIP

Now checking devices' ID ...

ID:10

Download from Www.Somanuals.com. All Manuals Search And Download.

•An error message "No devices detected

to connect. Power ON all devices in

system." appears . . .

... when a wrong port number is

selected.

... when the connection is wrong.

... when the device's ID number is

already in use.

... when the device's power is not

turned on.

Check the Serial Port selection, too.

To return to step 1, check the connection

and the device's power and try again.

Device Selection

Select device to control.

•When all serial COM ports are

occupied by other applications the

error message "Error--This application

will close. Check devices--Confirm that

power is ON." appears. Free a serial

COM port to start up JLIP Player

Software.

VCR

DISCONNECT

06:VCRCAMERA

CANCEL

VIDEO PRINTER

DISCONNECT

SELECT DEVICE(S)

Click on the name of the device you

wish to control. Clicking "OK" brings up

the MOVIE PLAYER window.

•It is possible to select a second device

of a different type simultaneously, but it

is impossible to select two same type

devices simultaneously.

Download from Www.Somanuals.com. All Manuals Search And Download.

MOVIE PLAYER WINDOW BUTTONS AND DISPLAYS

5.POWER button

Control-menu box

Menu bar

1.COUNTER system

3.ID number

2.Tape counter

display

Title bar

Icon button

4.FILE name

MOVIE PLAYER

File Edit Video Printer Help

Non Drop

ON OFF

00:00:00:00F

MEMO

COUNTER

POWER

ID 06 FILE

6.MEMO

SCENE

START

MODE

STILL

PLAY

SLOW

PROGRAM PLAYBACK

SCENE CUT IN

11. MODE display

8.START button

12. SCENE button

CUT OUT

REW

ELAPSED TIME

00:00:00:00F

IN/OUT

10. Camcorder's operation

buttons

13. IN/OUT point button

14. Message display

9.ELAPSED TIME

7.IN/OUT point display

Download from Www.Somanuals.com. All Manuals Search And Download.

1. COUNTER system

10.Camcorder's operation buttons

• Operate the camcorder.

2. Tape counter display

• Displays actual tape position.

Stop button

ex.

REW/REW Search button

Play button

00:

01:

45:

10F

(Hours : Minutes : Seconds : Frames)

FF/FF Search button

Pause button

3. ID number

• Displays the selected device's ID

number.

Reverse Slow button

Forward Slow button

4. FILE name

• Displays file name after saving the

program under a new name.

• To start Reverse/Forward Slow-motion

Search, first click the Pause button and

then the Reverse/Forward Slow button.

• Functions your camcorder does not

have cannot be performed by the above

buttons.

• Click "File" — "Open VCR Control

Window" on menubar to call up the

"VCR Control" window. You can control

the video source unit from this window.

ex. travel

5. POWER button

• Turns the device on and off.

• If power is not supplied to the

camcorder beforehand, you can not turn

the camcorder on and off by clicking

this button.

• Some camcorders cannot be turned on

and off by clicking this button.

11. MODE display

6. MEMO

• Displays the camcorder's mode when

operating the above buttons.

• If you wish to add some comment to the

file, you can input it.

12.SCENE button

ex. Europe Tour

• Plays back only one programmed scene

so that you can preview it.

7. IN/OUT point display

• You can set up to 99 in/out points per

file.

• Operates only the camcorder.

13.IN/OUT point button

• Registers the cut-in and -out points of

the scene you want to dub.

8. START button

• Starts editing. Scenes are recorded in

scene's numerical order. After starting

editing, this button changes to STOP

button.

14.Message display

• Displays the connected device mode,

etc.

9. ELAPSED TIME

• Displays the total elapsed time of all the

programmed scenes.

To exit from the MOVIE PLAYER

window, choose "Exit" from "File".

NOTE:

If you need the "MOVIE PLAYER HELP"

window, choose "Contents" from "Help".

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATIONS

Setting in/out points

Operating camcorder

PREPARE CAMCORDER

Set the camcorder's Power Dial to

"PLAY" and insert a recorded tape into

the camcorder.

PLAYBACK ON TV MONITOR

Click . Playback picture appears on the

TV monitor.

ᮣ

SET CUT IN/OUT POINTS

Select "Set Function" from "Edit" in the

Movie Player window and select "Edit

Tape".

PLAYBACK ON TV MONITOR

ᮣ

Click . The PLAY lamp lights in the

MODE display.

To set CUT IN/OUT points, click IN/OUT

button at the beginning and end of the

scene you want to dub.

•Playback picture appears on the TV

monitor.

•To confirm other operations, click other

buttons.

•Set CUT IN/OUT points so that the

CUT OUT point's value is larger than

the CUT IN point's.

•A scene with no CUT OUT point will

disable program playback and dubbing.

•If you set CUT IN point at the begin-

ning of the tape or if you set CUT OUT

point at the end of the tape, editing

may not function properly. Change

previously registered CUT IN/OUT

points slightly and try setting them

again.

•When connecting to a VHS-C

camcorder, rewind the tape to its

beginning and press COUNTER RESET

on the camcorder.

•The counters of DV-format digital

camcorders cannot be reset.

MOVIE PLAYER

File Edit Video Printer Help

Non Drop

COUNTER

POWER

00:20:35:16F ID 06 FILE

MEMO

ON OFF

PROGRAM PLAYBACK

SCENE

START

MODE

STILL

PLAY

SLOW

SCENE

CUT IN

CUT OUT

00:01:30:12F

00:07:15:21F

00:15:50:11F

00:03:27:14F

00:10:40:18F

00:20:33:10F

REW

ELAPSED TIME

00:10:04:28F

IN/OUT

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing back one programmed scene

MOVIE PLAYER

File Edit Video Printer Help

SELECT SCENE

Click on the line where the CUT IN/OUT

points you want to preview are displayed

and that line will be highlighted.

Non Drop

COUNTER

POWER

00:01:25:17F ID 06 FILE

MEMO

ON OFF

PROGRAM PLAYBACK

SCENE

STOP

MODE

STILL

PLAY

SLOW

SCENE

CUT IN

CUT OUT

00:01:30:12F

00:07:15:21F

00:15:50:11F

00:03:27:14F

00:10:40:18F

00:20:33:10F

START PLAYBACK

Click "SCENE".

•The camcorder searches the scene by

going to a point prior to the CUT IN

point and starts playback at the CUT IN

point. Playback stops after the CUT

OUT point is passed.

REW

ELAPSED TIME

00:10:04:28F

IN/OUT

Scene playback is executing.

Playing back all programmed scenes

MOVIE PLAYER

File Edit Video Printer Help

START PLAYBACK

Click "START".

•The camcorder plays back scenes in

numerical order and stops immediately

after the last scene's CUT OUT point.

•Only the camcorder moves.

Non Drop

COUNTER

POWER

00:01:25:17F ID 06 FILE

MEMO

ON OFF

PROGRAM PLAYBACK

SCENE

STOP

MODE

STILL

PLAY

SLOW

SCENE

CUT IN

CUT OUT

00:01:30:12F

00:07:15:21F

00:15:50:11F

00:03:27:14F

00:10:40:18F

00:20:33:10F

NOTES:

REW

ELAPSED TIME

00:10:04:28F

● During playback of programmed scenes, do

no operation other than pressing "STOP".

If other operations are done, a malfunction

may occur.

IN/OUT

Program playback is executing.

● If "SCENE" or "START" is clicked at the end

of tape, the camcorder will not function

properly.

● If the source tape has a blank portion,

scenes will not be edited properly.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATIONS (cont.)

Dubbing

You can record all programmed scenes onto

the tape in the recording deck.

Dubbing is possible only when the GR-

DVM1 is connected. (as of March, 1997)

MOVIE PLAYER

File Edit Video Printer Help

Non Drop

COUNTER

POWER

00:01:30:10F ID 06 FILE

MEMO

PREPARE NEW TAPE

ON OFF

Make sure the erase protection tab on

PROGRAM PLAYBACK

SCENE

STOP

MODE

STILL

PLAY

SLOW

the tape is present. Then insert it into the

recording deck and set the recording

deck to the Record-Pause mode.

SCENE

CUT IN

CUT OUT

00:01:30:12F

00:07:15:21F

00:15:50:11F

00:03:27:14F

00:10:40:18F

00:20:33:10F

START EDITING

Click "START" on the MOVIE PLAYER

window.

When editing stops, the camcorder

enters the Stop mode and the recording

deck enters the Record-Pause mode.

REW

ELAPSED TIME

00:10:04:28F

IN/OUT

Rec On ! !

•During dubbing, do no operation other

than pressing "STOP". If other opera-

tions are done, a malfunction may

occur.

STOP EDITING

Stop the recording deck.

NOTES:

● Also refer to the camcorder's instruction

manual on dubbing.

● There may be small margin between the

CUT IN/OUT points you input and the

dubbed scenes' ones.

● Dubbing is impossible using a camcorder

whose JLIP connector serves as an Edit

jack.

Download from Www.Somanuals.com. All Manuals Search And Download.

Saving the program list on hard disk

It is possible to save all programmed scene

information as a file in the computer.

MOVIE PLAYER

File Edit Video Printer Help

START SAVING

Select "Save As" from "File" on the

MOVIE PLAYER window.

•The "Save a program list" dialog box

appears.

New

Ctrl+N

Drop

COUNTER

00:01:33:04F ID 06 FILE

MEMO

Open

Ctrl+O

ON OFF

POWER

Save

Ctrl+S

Save As...

Ctrl+A

PROGRAM PLAYBACK

SCENE

START

MODE

STILL

PLAY

SLOW

ID Change

SCENE

Device Change

CUT IN

CUT OUT

Name Change

00:01:30:12F

00:07:15:21F

00:03:27:14F

00:10:40:18F

00:20:33:10F

Pause Time...

Open VCR Control Window

00:15:50:11F

ENTER FILE NAME

Input a file name (up to 8 characters) in

the "FILE NAME" field.

•The extension is jlp. ex.: travel.jlp

•You can also input a comment (up to

30 characters) in the "MEMO" field.

Close Serial

Initialize

Counter Reset

REW

ELAPSED TIME

00:10:04:28F

Exit

IN/OUT

SAVE FILE

Click "OK" and the file will be saved on

the hard disk which is in use.

Save a program list

FILE NAME

travel

DIRECTORY

ON OFF

POWER

Save

Ctrl+S

c: \

jlip

tape

Save As...

Ctrl+A

PROGRAM PLAYBACK

SCENE

START

MODE

STILL

PLAY

SLOW

travel. jlp

ID Change

SCENE

Device Change

CUT IN

CUT OUT

Name Change

Pause Time...

Open VCR Control Window

DRIVE

Close Serial

Initialize

Counter Reset

REW

ELAPSED TIME

00:00:00:00F

MEMO

Exit

CANCEL

Europe Tour

IN/OUT

Correcting and cutting the programmed counter data

Correcting the program counter data

Cutting the counter data being set up

DESIGNATE SCENE

Double-click on the scene you want to

modify.

DESIGNATE SCENE

Click on the scene you want to cut.

CUT SCENE

OR...

Click on the scene you want to modify

and choose "Modify" from "Edit".

Choose "Cut" from "Edit".

•The message "Scene No. will be

deleted." appears.

•The "Modify Edit Points" dialog box

appears (੬ pg. 55).

To cut the scene, click on "OK".

ENTER NEW DATA

Click on the part to be corrected and

input a new value there. To correct the

data, click on "OK".

Cutting all programmed scenes

CUT SCENE

Choose "All Clear" from "Edit". The

message "OK to delete all programmed

scenes ?" appears. To cut, click on "OK".

Download from Www.Somanuals.com. All Manuals Search And Download.

Transferring the programmed scene to

an other position

Copying a programmed scene and

transferring it to an other position

DESIGNATE SCENE TO BE

COPIED

TRANSFERRED

Click on the scene you want to copy.

Click on the scene you want to transfer

and choose "Cut" from "Edit".

STORE DESIGNATED SCENE IN

MEMORY

Choose "Copy" from "Edit".

•The message "Scene No. will be

deleted." appears.

To cut, click on "OK".

DESIGNATE POSITION

Click on the scene number which is

above the position to which the copied

scene is to be transferred.

DESIGNATE POSITION

Click on the scene number which is

above the position to which the scene is

to be transferred.

TRANSFER COPIED SCENE

Choose "Paste" from "Edit".

TRANSFER CUT SCENE

Choose "Paste" from "Edit".

MOVIE PLAYER

File Edit Video Printer Help

Modify...

Cut

Ctrl+E

Ctrl+X

Drop

COUNTER

00:27:10:21F ID 06 FILE

MEMO

Modify Edit Points

All Clear

Del

ON OFF

POWER

Copy

Paste

Ctrl+C

Ctrl+V

Enter the new [in] and/or [out] points.

PROGRAM PLAYBACK

SCENE

START

MODE

STILL

PLAY

SLOW

Set Function

SCENE

CUT IN

CUT OUT

IN POINT

00:05:55:12F

00:12:10:12F

00:23:22:10F

00:10:37:12F

00:16:50:18F

00:27:08:16F

OUT POINT 00

REW

ELAPSED TIME

00:13:08:12F

CANCEL

IN/OUT

Overwriting the file

Saving any previously saved program using the same name. Overwrite erases the previously

saved data for that file.

OVERWRITE FILE

After opening a file and modifying counter data (੬ pg. 54), choose "Save" from "File" on

the MOVIE PLAYER window and click on "OK".

•The message "This file already exists. Do you want to overwrite it ?" appears.

To overwrite the file, click on "OK".

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO PRINTER WINDOW BUTTONS AND DISPLAYS

2.POSITION button

1.POWER button

Title bar

Icon button

Video Printer

POWER ON OFF POSITION

3.ID number

ID 20

HIGH LOW

STROBE SPEED

9.STORE button

10. PRINT button

STORE

STROBE

SELECTED

SAME

ON OFF

SELECT

SOURCE

MEMORY

OFF

PIX STABILIZER

11. SELECT

(scene select)

button

MULTI-PIX

CONTENT

12. CLOSE button

Aperture Off ! !

8.PIX STABILIZER button

7.STROBE SPEED button

6.CONTENT button

5.MULTI-PIX button

4.Message display

Download from Www.Somanuals.com. All Manuals Search And Download.

1. POWER button

10.PRINT button

• Turns the device on and off.

When connected to the GV-PT2

• Print command is available.

2. POSITION button

• Selects the position to store a scene in

memory for Multi-Print.

11. SELECT (scene select) button

• Switches between "SOURCE" (images

from camcorder or VCR) and

"MEMORY" (scenes stored in memory)

for display on TV monitor.

3. ID number

• Displays the selected device's ID

number.

12.CLOSE button

4. Message display

• Closes the "Video Printer" window.

• Displays the operating mode of the

selected device.

5. MULTI-PIX button

ᮡ

• Select by clicking ( /ᮢ) button.

OFF : Single print

: 4 shots on one sheet

: 16 shots on one sheet

6. CONTENT button

ᮡ

• Select by clicking ( /ᮢ) button.

STROBE : Stores the selected number of

images at short intervals, and

prints them all on one sheet.

SELECTED : Prints 4 or 16 selected scenes

on one sheet.

SAME

: Prints the same scene 4 or 16

times on one sheet.

7. STROBE SPEED button

• Effective when "STROBE" is selected

from "CONTENT".

HIGH : When printing in the Strobe Print

mode, the GV-PT2 stores scenes

at intervals of approximately 1/

15 second.

LOW : When printing in the Strobe Print

mode, scenes are stored at

intervals of approximately 1/2

second.

8. PIX STABILIZER button

ON : If the scene you want to print is

jittery, select "ON" to stabilize it.

OFF : Usually set to "OFF".

9. STORE button

• Stores scenes and titles you want to

print in the video printer's memory.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO PRINTER OPERATION (GV-PT2)

Printing

Before printing, perform the procedure listed below.

● Connect to image and sound source (੬ pg. 42, 43).

● Set VCR to external input.

● Set TV to VIDEO mode so that images from video printer appear.

BRING UP VIDEO PRINTER

STORE SCENE

Click "STORE" on the "Video Printer"

window at the scene you want to print.

•The selected scene is stored in memory

and appears on the TV monitor.

1 _WINDOW

Select "Set-up" from "Video Printer" on

the MOVIE PLAYER window.

•The "Video Printer" window appears.

•To view the buttons on the MOVIE

PLAYER window, move the "Video

Printer" window to the right and up

keeping the title bar on the "Video

Printer" window clicked.

Insert print paper into the video printer

and click "PRINT".

•Also refer to the video printer's

instruction manual.

PLAYBACK

ᮣ

Click on the MOVIE PLAYER window.

•The "Video Printer" window appears

behind the MOVIE PLAYER window.

•To view the "Video Printer" window,

click the title bar labelled "Video

Printer".

The following print styles are also available:

● Printing the same scene 4 or 16 times on one sheet. (Multi-Print)

● Printing various scenes on the same print sheet. (Multi-Print)

● Printing a scene within a scene. (Inset Print)

● Storing a selected number of images at short intervals and printing them on one sheet.

(Strobe)

Also refer to the video printer's instruction manual.

MOVIE PLAYER

File Edit Video Printer Help

Video Printer

Set-up

Drop

COUNTER

POWER

00:00:00:00F ID 06 FILE

MEMO

POWER ON OFF POSITION

ID 20

ON OFF

HIGH LOW

STROBE SPEED

STORE

PROGRAM PLAYBACK

SCENE CUT IN

SCENE

START

MODE

STILL

PLAY

SLOW

STROBE

SELECTED

SAME

CUT OUT

ON OFF

SELECT

SOURCE

MEMORY

OFF

PIX STABILIZER

MULTI-PIX

CONTENT

REW

ELAPSED TIME

00:00:00:00F

IN/OUT

Aperture Off ! !

Download from Www.Somanuals.com. All Manuals Search And Download.

Quitting the "Video Printer" window

Quitting the MOVIE PLAYER window

CLICK "CLOSE"

•The "Video Printer" window closes.

CHOOSE "EXIT" FROM "FILE"

•The MOVIE PLAYER window closes.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO PRINTER OPERATION (GV-PT2)(cont.)

Auto Capture

Select "Video Printer" — "Set-up" in the

1 _{MOVIE PLAYER window.}

Preparation

•Video Printer window appears.

• Load the tape into the video unit.

• Convert the captured data to JLIP Player

software data and store it (੬ p. 35).

• Select file name (੬ p. 54).

• Prepare for printing (refer to the GV-PT2

instruction manual).

Select the number of scenes (OFF/4/16)

2 _{and select "SAME" or "SELECTED" for the}

content.

•Select this by clicking the buttons

ᮡ

(

/ᮢ).

• Select desired layout using the remote

control unit provided with the GV-PT2.

To Print Captured Video Data with

Video Printer

Captured video data can be automatically

scanned and printed.

You can print OFF, 4 or 16 images on one

sheet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click Title in the MOVIE PLAYER

3 _{window and activate the window.}

Select "Edit" — "Set Function" — "Auto

4 _Capture".

Click "START"

5 _{•The captured video data set first is}

searched and stored in the video

printer.

•When the data has been stored, the

message "Image has been captured by

printer." appears.

•If the number of scenes was set to

"OFF", or "4 or 16" in step 2 and then to

"SAME", you can start printing simply

by clicking "PRINT".

Auto-Capture

Image has been captured by printer.

NEXT SCENE…

CANCEL

•If the number of scenes was set to "4 or

16" in step 2 and then to "SELECTED",

click <Next Scene>. The next scene is

automatically searched and stored in

the video printer.

Click "PRINT" to start printing.

NOTES:

To print only the cut-in scene on the

edited tape

1 Perform editing (refer to pages 50 through

52).

2 Print (follow steps 1 through 5 above).

● Select "Auto Capture" in step 4.

● Click "START" in step 5. The cut-in point

of Scene No. 1 is automatically

searched and stored in the video printer.

● You cannot start storing from Scene No.

2 or subsequent scenes.

● Even if the video unit is in Stop mode,

clicking "START" automatically starts

playback to search the cut-in point of

Scene No. 1.

● If you want to print a particular scene

only, click "SCENE" in step 5.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED OPERATIONS

Changing ID number

The device's ID number is preset at factory as follows:

ex. Camcorder: 06 or 07 Video printer: 20

When connecting more than two same type devices, the same ID numbers will exist and a

malfunction can occur. To avoid a malfunction, change the ID numbers.

It is recommended to change the ID number of an already connected device before connect-

ing the same type device.

ACCESS "ID CHANGE" DIALOG

BOX

Choose "ID Change" from "File" on the

MOVIE PLAYER window.

SET ID NUMBER

Click "OK".

•The message "The device ID will be

changed." appears.

•The "ID Change" dialog box appears.

Clicking "OK" again sets that ID

number and brings up the MOVIE

PLAYER window.

SELECT DEVICE

Click on the name of the device and

"CHANGE".

•The dialog box to enter new ID number

appears.

NOTES:

● After step 4, perform the following

‘Connecting other device during operation’.

● Do not enter ID number "0" because "JLIP

Player Software" does not recognize "ID 0".

3 ^{ENTER NEW ID NUMBER}

ID Change

Select the device to change.

VCR

ID Change

06:VCRCAMERA

CHANGE

Enter a number between 1 and 99.

ID =

VIDEO PRINTER

CHANGE

CANCEL

Connecting other device during operation

When connecting an other device during operation or changing ID numbers, initializing is

necessary to confirm the connected devices. (Not necessary to run "JLIP Player Software" from

beginning again.)

INITIALIZE

Choose "Initialize" from "File" on the MOVIE PLAYER window.

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the name of the device

Changing the device to use while

connecting over two same type

devices

ACCESS "NAME CHANGE"

DIALOG BOX

Choose "Name Change" from "File" on

the MOVIE PLAYER window.

ACCESS "DEVICE SELECTION"

DIALOG BOX

•The "Name Change" dialog box

appears.

Choose "Device Change" from "File" on

the MOVIE PLAYER window.

•The "Device Selection" dialog box

appears.

SELECT DEVICE

Click on the name of the device and

"CHANGE".

•The dialog box to enter new name of

the device appears.

SELECT DEVICE

Click on the name of the device and

"OK".

3 ^{ENTER NEW NAME}

NOTE:

It is impossible to use two same type devices

simultaneously.

SET NEW NAME

Click "OK".

Device Selection

Select Devices to control.

VCR

•The message "Device name will be

changed." appears.

Clicking "OK" again sets that device

name and brings up the "Name

Change" dialog box.

DISCONNECT

06:VCRCAMERA (1)

07:VCRCAMERA (2)

CANCEL

RETURN TO MOVIE PLAYER

VIDEO PRINTER

DISCONNECT

WINDOW

Click "CLOSE".

Name Change

Select the device to change.

VCR

06:VCRCAMERA

CHANGE

When Using the Video Capture Software

The JLIP Player Software and JLIP Video

Capture Software cannot run simultaneously.

When you want to run the JLIP Video

Capture Software, first select "Close Serial"

from "File" on the menu bar. To resume using

the JLIP Player Software, click the "JLIP"

button in the JLIP Video Capture Software

and select "Open Serial" from "File" on the

JLIP Player Software's menu bar.

VIDEO PRINTER

Name Change

Enter new name (up to 20 letters).

VCRCAMERA (1)

OK CANCEL

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED OPERATIONS (cont.)

Adjusting the gap between the stored edit-start point in the computer and the

dubbed one in the recording deck

During dubbing, the beginning of the scene stored in the computer can be missed or the scene

prior to the transition you chose for the edit-start point can be dubbed into the recording deck.

When these cases occur, adjust the gap for more accurate editing.

CHECK EDIT-START TIMING

After dubbing (੬ pg. 52), play back the

dubbed scene.

DETERMINE VALUE

Click "OK".

•This value is stored in the computer.

ACCESS "PAUSE TIME CORREC-

TION" DIALOG BOX

Choose "Pause Time" from "File" on the

MOVIE PLAYER window.

•The "Pause Time Correction" dialog box

appears.

CHECK EDIT-START TIMING

AGAIN

To check the corrected edit-start timing,

dub the stored scenes and play them

back.

NOTE:

ENTER VALUE

To adjust the edit-start timing, enter a

new value from 0.00 sec. to 2.60 sec.

Even if the edit-start timing is adjusted, there

can be a slight margin between the adjusted

edit-start point and the dubbed scenes' one.

When the scene prior to the transition

you chose for edit-start point is dubbed:

Enter a smaller value than 1.30.

When the beginning of the scene stored

in the computer is missed:

Enter a larger value than 1.30.

•Factory preset is 1.30 sec..

MOVIE PLAYER

File Edit Video Printer Help

New

Ctrl+N

Drop

COUNTER

00:00:01:20F ID 06 FILE travel

MEMO Europe Tour

Open

Ctrl+O

Pause Time Correction

ON OFF

POWER

Save

Ctrl+S

Save As...

Ctrl+A

Type in the value from 0.00(sec) to 2.60(sec),

to adjust pause time during editing.

PROGRAM PLAYBACK

SCENE

START

MODE

STILL

PLAY

SLOW

ID Change

SCENE

CUT IN

CUT OUT

Device Change

Name Change

00:01:30:12F

00:07:15:21F

00:15:50:11F

00:03:27:14F

00:10:40:18F

00:20:33:10F

Pause Time...

Pre-start time = 1.30 (sec)

Open VCR Control Window

Close Serial

Initialize

Counter Reset

REW

CANCEL

ELAPSED TIME

00:10:04:28F

Exit

IN/OUT

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

ⅷ POSSIBLE CAUSE

Ⅵ CORRECTIVE ACTION

MESSAGE

––

Error

This application will

––

ⅷ The COM port used for the JLIP connector is not

selected, or the COM port is selected but the

connection is wrong.

Ⅵ Check the connected COM port and select it on the

"Serial Port Selection" screen (੬ pg. 46).

close.

Check devices

that power is ON.

Confirm

No devices detected to

connect.

Power ON all devices in

system.

ⅷ Power is not supplied or the connection is wrong.

Ⅵ Connect the devices correctly and turn them on

(੬ pg. 42, 43).

Communication error

(&H (number))

Check cable connection.

ⅷ Device is not turned on or cable is disconnected.

Ⅵ Connect the device correctly and turn it on

(੬ pg. 42, 43).

Ⅵ If device was turned off and on again during

operation, click "OK". All devices should function

properly.

Select the device to control.

ⅷ The line where the name of the device to use

appears is not clicked.

Ⅵ Click on it and "OK" (੬ pg. 47).

No video cassette!!

Load a video cassette to ID

(number).

ⅷ The video cassette is not loaded in the camcorder.

When the video cassette is removed during

operation, this message appears.

Ⅵ Insert the video cassette into the camcorder.

Invalid entry in scene

ⅷ The value of the CUT OUT point is smaller than

the CUT IN point's.

Ⅵ Set the value of the CUT OUT point so that it is

larger than the CUT IN point's (੬ pgs. 50, 54).

(number) (There is IN > OUT

condition). Correct the time

or delete the scene.

Select a number between 0

and 24.

ⅷ When correcting the CUT IN/OUT points, the

value you set differs from the original by over 25

frames.

Ⅵ Select integral number from 0 to 24 (੬ pg. 54).

Invalid frame number on drop

frame counter.

ⅷ Because the DV-format digital camcorder uses the

drop frame system, inputting frame 00 and 01 is

impossible.

Ⅵ Input frame value other than 00 or 01

(੬ pgs. 48, 54).

The monitor displays of the application software illustrated in this manual may differ from

those you are actually viewing depending on the operating environment of your computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAJOR SPECIFICATIONS

JLIP VIDEO CAPTURE DOCKING STATION

Connectors

S-Video

: Output Y : 1.0 Vp-p, 75 ohms

C : 0.3 Vp-p, 75 ohms

(S2 output)

Video

: Input 1.0 Vp-p, 75 ohms (pin jack)

(CAPTURE INPUT (EXT.)/PRINTER connector)

: Output 1.0 Vp-p, 75 ohms (pin jack)

(VIDEO output connector)

: Output –8 dB, 1 kiloohm (pin jack)

: 3.5 mm dia., 4-pole, mini-head jack

(compatible with EIAJ RC-5325 plug)

: Mini DIN 8-pin

Audio

JLIP (x 2)

Digital

Multi-connector

Editing connector

DC output

: 34-pin

: 3.5 mm dia., 2-pole

: 5 V DC

Captured image sizes

Operating temperatures

Dimensions

: 768 x 552 pixels, 80 x 60 pixels

: 5 to 30° C

: 113W x 61H x 145D mm

: Approx. 395 g

Weight

Power supply

: 6.3 V DC

* E. & O. E. Design and Specifications subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

Arrange Index ................................. ੬ pg. 31

Automatic Capture (AUTO) ....... ੬ pg. 26, 28

JPEG................................................ ੬ pg. 30

Main Window................................. ੬ pg. 20

Memory button ............................... ੬ pg. 20

Menu bar .................................. ੬ pg. 20, 48

Bitmap ...................................... ੬ pg. 24, 30

Capture Mode................................. ੬ pg. 30

Change ID ................................ ੬ pg. 31, 62

COM Port ................................. ੬ pg. 17, 46

Counter reset .................................. ੬ pg. 32

Counter Value Change.................... ੬ pg. 32

Create New Folder ......................... ੬ pg. 33

Open Index .................................... ੬ pg. 33

Open JLIP (jlp) File ......................... ੬ pg. 34

Operate VCR ............................ ੬ pg. 23, 49

Picture Format ................................ ੬ pg. 30

Program Capture..................... ੬ pg. 26 – 27

Delete Index Image and Full Image

........................................................ ੬ pg. 31

Desktop Window................ ੬ pg. 20, 48, 56

Device Selection ............................ ੬ pg. 18

Dubbing ......................................... ੬ pg. 52

Save As JLIP (jlp) File ...................... ੬ pg. 35

Save Image As ................................ ੬ pg. 29

Setup Menu .............................. ੬ pg. 22, 25

Step by Step Capture ...................... ੬ pg. 25

Save Index ...................................... ੬ pg. 29

Edit Menu ....................................... ੬ pg. 22

Exit (Close)...................................... ੬ pg. 19

Transfer Rate ................................... ੬ pg. 17

Field Picture ................................... ੬ pg. 30

File Menu ....................................... ੬ pg. 22

Frame Picture ........................... ੬ pg. 21, 30

Full image data ............................... ੬ pg. 21

Video Capture......................... ੬ pg. 24 – 28

Video Printer........................... ੬ pg. 58 – 61

Window Menu................................ ੬ pg. 20

Help Menu ............................... ੬ pg. 23, 49

Index image ........................ ੬ pg. 21, 26, 28

Index image data ............................ ੬ pg. 21

Initialize ................................... ੬ pg. 17, 46

Input button .................................... ੬ pg. 20

Install ........................................ ੬ pg. 15, 45

Interval Capture .............................. ੬ pg. 28

IRQ ................................................. ੬ pg. 37

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Cooktop K31ECG User Manual
Insignia Mouse NS PNC5011 User Manual
Insignia Portable Stereo System NS B3111 User Manual
JVC Flat Panel Television AV 28BT80EP User Manual
JVC MP3 Player XA MP2 User Manual
Keating Of Chicago Fryer 7 05 User Manual
Kenwood Cassette Player KRC 665 User Manual
KitchenAid Electric Heater KAWE750V User Manual
Kodak Film Camera 3100AF User Manual
Kramer Electronics Video Gaming Accessories VA 10 User Manual