ENGLISH
LT-Z32SX4B
LT-Z26SX4B
LT-Z32SX4S
LT-Z26SX4S
INSTRUCTIONS
WIDE LCD PANEL TV
LCT1732-002A
Download from Www.Somanuals.com. All Manuals Search And Download.
Pixel defects
LCDs use collections of fine points (“pixels”) to display images. While there is no problem with
more than 99.99% of these pixels, please understand that a very small number of pixels may not
light, or may light all the time.
Distance recommendations
Avoid improper installation and never position the unit
where good ventilation is impossible.
200 mm
200 mm
150 mm
150 mm
When installing this TV, distance recommendations
must be maintained between the set and the wall, as well
as inside a tightly enclosed area or piece of furniture.
Keep to the minimum distance guidelines shown for
safe operation.
50 mm
Failure to take the following precautions may cause damage to the television
or remote control.
DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)
DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)
DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT place any naked flame sources, such as lighted candles, on the TV.
DO NOT subject the TV to direct sunlight.
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.
Never use any cleaner or detergent on it.
If there is a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself
or remove the rear cover.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
„ Cleaning the screen
The screen is coated with a special thin film to reduce reflection. If this film is damaged, uneven
colours, discolouration, scratches, and other problems that cannot be repaired may occur. Pay
attention to the following when handling the screen.
• Do not use glue or adhesive tape on the screen.
• Do not write on the screen.
• Do not allow the screen to come in contact with any hard objects.
• Do not allow condensation to form on the screen.
• Do not use alcohol, thinner, benzene or other solvents on the screen.
• Do not rub the screen hard.
CAUTION:
• Operate only from the power source specified (AC 110 – 240 V, 50/60 Hz) on the unit.
• Avoid damaging the AC plug and power cord.
• When you are not using this unit for a long period of time, it is recommended that you disconnect
the power cord from the main outlet.
D.I.S.T. demonstration
To start the D.I.S.T. demonstration:
Press the H button to display the menu bar. Then press the yellow button.
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.
To quit the D.I.S.T. demonstration:
Press the yellow button, b button, 6 p buttons or any of the number buttons.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV ...................................5
Installation.................................................. 5
Removing the terminal covers ................... 6
Connecting the aerial and video cassette
Connecting the power cord to the AC
outlet....................................................... 8
Putting the batteries into the remote
control..................................................... 8
Initial settings (Setup tour) ......................... 8
BRIGHT.................................................... 25
TINT ......................................................... 25
CINEMA SURROUND ............................. 29
TV buttons and functions......................10
Turn the TV on from standby mode ......... 10
Choose a TV channel .............................. 10
Adjust the volume .................................... 10
Using the Menu........................................ 10
Remote control buttons and
functions..............................................11
Choose a TV channel and watch images
from external devices ........................... 12
Adjust the volume .................................... 13
Display function........................................ 13
ZOOM function......................................... 14
CINEMA SURROUND function................ 15
Using the “Freeze” function...................... 15
Using the “Multi-picture” function ............. 16
RETURN PLUS function and Return
AUTO SHUTOFF ..................................... 33
LANGUAGE ............................................. 38
AI VOLUME.............................................. 38
TELETEXT LANGUAGE.......................... 39
function................................................. 17
Favourite channel function....................... 18
Operating a JVC brand DVD player......... 19
Teletext function ....................................20
Basic operation ........................................ 20
Using the List Mode ................................. 20
Hold.......................................................... 21
Sub-page ................................................. 21
Reveal...................................................... 21
Size.......................................................... 21
Index ........................................................ 22
Cancel...................................................... 22
Displaying a computer screen.............. 40
Connecting to the computer..................... 40
Watching images from a computer .......... 40
Table of signals for each type of
computer............................................... 40
Additional preparation .......................... 41
Connecting external equipment ............... 41
Using the TV’s menu..............................23
Basic operation ........................................ 23
CH/CC numbers ..................................... 44
Troubleshooting .................................... 45
Specifications ........................................ 47
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
• When you install the TV on the wall, only use a JVC wall mounting unit (optional) which is
designed for this TV.
• Make sure that the TV is installed on the wall by a skilled installer.
Installation
Cautions for installation
• Install the TV in a corner on a wall or on the floor so as to keep cords out of the way.
• The TV will generate a slight amount of heat during operation. Ensure that sufficient space is
available around the TV to allow satisfactory cooling. See “Distance recommendations” on
page 2.
Using the stand
This TV comes with a table top stand already attached.
This stand can be used to adjust the direction of the TV screen 5° up, 10° down, and 20° to the left
or right.
„ Tilt the TV up and down:
While holding the bottom of the stand with one
hand, use your other hand to hold the middle of
the top of the TV and slowly tilt the TV up and
down.
• As a safety measure, the stand is
constructed so that it requires a certain
amount of force to tilt the TV.
„ Rotate the TV to the left and right:
While holding the bottom of the stand with one
hand, use your other hand to hold the edge of
the panel and slowly adjust the direction of the
TV screen.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
„ Cable holder
A cable holder which is used to keep the
connection cables tidy is attached to the back
of the stand. Gently squeeze the left and right
of the cable holder and pull it to remove it from
the stand. After putting the cables in the cable
holder, attach it to the back of the stand again.
cable holder
Removing the terminal covers
There are connection terminals behind the covers on the left and right of the rear of the TV.
Remove these two covers before connecting an antenna or VCR.
Remove the covers by removing the hooks.
When replacing the covers, place the side of
the covers against the TV and insert the hooks.
• Leave the covers off if they do not fit properly. Do not force to replace the covers. Doing so
may cause damage to the connection cables and the covers.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Connecting the aerial and
video cassette recorder (VCR)
without terminal covers
Caution
• Turn off all the equipment including the
TV before connecting anything.
• Aerial cable is not supplied. Use a good
quality 75-ohm coaxial cable.
• Read the manual that came with the VCR
before connecting.
IN
If not connecting a VCR (follow 1):
Connect an aerial cable to the aerial
socket on this TV.
IN
If connecting a VCR:
1 Connect the aerial cable to the
aerial input socket on the VCR, and
connect the VCR and TV with
another aerial cable
3
2
1
2 Connect the VCR’s VIDEO OUT
(video output) terminal and the
TV’s VIDEO terminal with a video
cable
To connect a VCR to the TV with an S-
VIDEO cable:
1
Connect the VCR’s S-VIDEO OUT (S-
VIDEO output) terminal and TV’s S
VIDEO terminal with an S-VIDEO cable
A, instead of connecting with a video
cable.
cable will be ignored in case you connect
a VCR to the TV with both video cable
and S-VIDEO cable.
3 Connect the VCR’s VIDEO OUT
(audio L/R output) terminals and
the TV’s AUDIO terminals with an
audio cable
• To connect additional external devices,
please see “Connecting external
equipment” on page 41.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Connecting the power cord to
the AC outlet
Initial settings (Setup tour)
When the TV is first turned on, it goes into
the initial settings mode, and you will see the
JVC logo. Follow the instructions on the
screen display to make the initial settings.
Insert the AC plug on the power cord from
the TV into AC outlet.
Caution
• Operate only from the power source
specified (AC 110 – 240 V, 50/60 Hz)
on the unit.
# button
PIP/TV/DVD
switch
• Remove the AC plug from the outlet to
completely disconnect the TV from the
power supply.
Putting the batteries into the
remote control
6
buttons
Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.
1 Make sure to set the PIP/TV/DVD
switch on the remote control to the
TV position
• You cannot turn the TV on when the
PIP/TV/DVD switch is set to the DVD
position.
2 Press the # button on the remote
control
• Follow the warnings printed on the
batteries.
• Battery life is about six months to one
year, depending on how much you use the
remote control.
• The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as you need to.
• If the remote control does not work
properly, replace the batteries.
The TV turns on from standby mode and
the JVC logo is displayed.
• Check that the AC plug on the power
cord from the TV is connected to AC
outlet.
Remote control
sensor
Power lamp
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
• If the JVC logo does not appear this is
because your TV has already been
turned on for the first time:
use the “LANGUAGE”, “TELETEXT
LANGUAGE” and “AUTO
PROGRAM” functions to make the
initial settings. For details, see “SET
UP menu” on page 34.
5 Press the 6 buttons to choose a
group. Then press the a button
The AUTO PROGRAM function starts.
The TV channels you receive are
automatically stored in the programme
numbers (PR) list.
>> AUTO PROGRAM
CH 28
3 Press the a button
14%
The LANGUAGE menu appears.
OK
D0004-EN
• To stop the AUTO PROGRAM
6 After the TV channels have been
registered in the programme
numbers (PR), the EDIT menu
appears
4 Press the 6 buttons to choose
ENGLISH. Then press the a
button
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
The TELETEXT LANGUAGE menu
appears. Set the teletext language group
that corresponds to the language of the
teletext programme that you want to watch.
For details, see “TELETEXT
CH
CH
CH
CH
CH
CH
CC
CC
CC
21
22
23
24
25
26
01
02
03
LANGUAGE” on page 39.
ID
MANUAL
OK
MOVE
> TELETEXT LANGUAGE
INSERT DELETE
D0038-EN
GROUP-1
GROUP-2
GROUP-3
GROUP-4
• You can proceed to edit the
programme numbers (PR) list using
the EDIT/MANUAL function. For
details, see “EDIT/MANUAL” on
page 34.
OK
D1003-EN
• If a TV channel you want to view is
not stored in the programme numbers
(PR) list, you can register it using the
MANUAL function. For details, see
“EDIT/MANUAL” on page 34.
• The AUTO PROGRAM function does
not store a TV channel to the
programme number PR 0 (AV).
• If you do not need to use the EDIT/
MANUAL function, press the a
button to close the EDIT menu.
Now, setting up is complete. Please
enjoy your new JVC TV!
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TV buttons and functions
Turn the TV on from standby
mode
1
Press the A button or the CHANNEL
p buttons to turn the TV on from
standby mode.
When the TV is turned on, the power lamp
lights blue.
To turn the TV off:
Press the A button again.
The power lamp goes off.
2
Caution
• The A button on the TV does not fully
isolate the TV from the AC supply. If
you are not going to use the TV for a
long period, be sure to disconnect the
AC plug from the AC socket.
Choose a TV channel
Press the CHANNEL p buttons to
choose a programme number (PR) or
a VIDEO terminal
VIDEO terminal.
3
4
Adjust the volume
5
6
Press the VOLUME q buttons
The volume level indicator appears.
Using the Menu
7
8
Use the MENU/OK button
Refer to “Using the TV’s menu” (see
page 23) for details of using the menu.
Refer to the pages in parentheses for details.
1 Remote control sensor
2 Power lamp (page 8)
3 TV/VIDEO button
4 MENU/OK button (page 23)
5 CHANNEL p buttons
6 (page 23)
6 VOLUME q buttons
5 (page 23)
7 A (Stand by) button
8 Headphone jack (mini jack) (page 41)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
1 Muting button
2 Number buttons
3 1 button
4 c button
5 2 button
6 4 button
7 7 buttons
8 5 button
9 6 p buttons
0 VCR/DVD/Teletext control buttons
- p buttons
1
2
~
!
= d (Favourite) button
~ # (Standby) button
! PIP/TV/DVD switch
@ g (Text) button
3
4
@
#
# Colour buttons
$ H button
% a button
^ b button
5
6
$
%
& 7 q buttons
* f (Freeze) button
( X (Multi) button
) c (Select) button
7
8
^
&
Turn the TV on or off from
standby mode
9
*
(
Press the # (standby) button to turn
the TV on or off
When the TV is turned on, the power lamp
lights blue.
• The power can be turned on by pressing
the 4 button, 6
p buttons or Number buttons.
0
-
=
)
To turn the TV on or off, set the PIP/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the PIP/TV/DVD switch on the remote
control is set to the DVD position, the TV
will not be turned on or off even if the #
button is pressed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
• Since this TV is designed to make full use
of the resolution of the original video
source, the motion may appear unnatural
when the video source is input with
progressive-scanning component signals.
• If this happens, change the output setting
of the connected device to interlace-
scanning component signal output. See
the instructions that came with the device
for more information.
Choose a TV channel and
watch images from external
devices
„ Use the number buttons:
Enter the programme number (PR)
of the channel using the number
buttons.
Example:
• PR 6 → press 6
• PR 12 → press 1 and 2
• The PC sound is the same as the VIDEO-3
sound.
To return to a TV channel:
Press the 4 button, the
6 p buttons or the number
buttons.
„ Use the 6 p buttons:
Press the 6 p buttons
to choose the programme number
(PR) you want or a VIDEO
terminal.
To use the programme number PR 0
(AV):
When the TV and VCR are connected only
by the aerial cable, choosing the programme
number PR 0 (AV) allows you to view
images from the VCR. Set the VCR RF
channel to the programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL” on page 34.
„ Use the 4 button:
Press the 4 button to
choose a VIDEO terminal.
or
Programme
numbers
PR 1 – PR 99
or
• The leading character is changed from V
to S (eg V1 is changed to S1) when
VIDEO-1 or VIDEO-2 is connected to the
S terminal.
• If you do not have a clear picture or no
colour appears, follow the operation
procedure “COLOUR SYSTEM” on
page 27.
• If you cannot hear the normal sound even
if the picture of the TV channel appears
normally. Follow the description “EDIT/
MANUAL” on page 34 to use the
MANUAL function to change the
SYSTEM setting.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
PR LIST:
The programme number (PR) and VIDEO
terminal list is displayed.
Pressing the a button after choosing the
programme number (PR) or VIDEO terminal
• For programme numbers (PR) for which
the CHANNEL GUARD function is set,
the n (CHANNEL GUARD) mark is
displayed. For details see “CHANNEL
GUARD” on page 31.
Adjust the volume
Press the 7 q buttons to
adjust the volume.
The volume level indicator appears and the
volume changes as you press the 7
q buttons.
„ Muting the sound
Press the (muting) button to
l
turn off the sound.
Pressing the (muting) button again
l
• The VIDEO terminals are registered after
the programme number PR 99.
restores the previous volume level.
• For programme numbers (PR) which is
registered as a favourite channel, the d
(favourite) mark is displayed. For details
see “Favourite channel function” on
page 18.
Display function
You can see the channel number of the
programme you are watching or the PR
LIST.
From the PR LIST, you can choose a channel
or VIDEO terminal.
Press the
the information you want to see.
button to display
5
Pressing the
button changes the
5
display as follows:
PR LIST
PR
ID
Channel number display
AV
01
02
03
04
05
06
07
08
09
No indication
OK
-10
+10
D0011-EN
Channel number display:
The channel number and channel name
(when the channel name is registered) of the
programme you are watching or the VIDEO
terminal number is displayed.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
16:9 ZOOM:
This zooms up the wide picture (16:9 aspect
ratio) to the full screen.
ZOOM function
You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.
• The ZOOM mode is fixed at FULL when
you are using the TV as a PC screen.
16:9 ZOOM SUBTITLE:
This zooms up the wide picture (16:9 aspect
ratio) with subtitles to the full screen.
AUTO:
When a WSS (Wide Screen Signalling)
signal, which shows the aspect ratio of the
picture, is included in the broadcast signal or
the signal from an external device, the TV
automatically changes the ZOOM mode to
16:9 ZOOM mode or FULL mode according
to the WSS signal.
If a WSS signal is not included, the picture is
displayed according to the ZOOM mode set
with the 4:3 AUTO ASPECT function.
• For details of the 4:3 AUTO ASPECT
function, see “4:3 AUTO ASPECT” on
page 28.
FULL:
This uniformly stretches the left and right
sides of a normal picture (4:3 aspect ratio) to
fill the wide TV screen.
• For 16:9 aspect ratio pictures that have
been squeezed into a normal picture (4:3
aspect ratio), use the FULL mode to
restore the picture to its original shape.
• When the AUTO (WSS) mode does not
function correctly due to poor WSS signal
quality or when you want to change the
ZOOM mode, press the c button
and change to another ZOOM mode.
„ Choose the ZOOM mode
1 Press the c button to display
the ZOOM menu
REGULAR:
ZOOM
Use to view a normal picture (4:3 aspect
ratio) as this is its original shape.
AUTO
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL
PANORAMIC:
OK
This stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fill the
screen, without making the picture appear
unnatural.
D0009-EN
2 Press the 6 buttons to choose a
ZOOM mode. Then press the a
button
The picture expands and the chosen
ZOOM mode is displayed in about 5
seconds.
• The top and bottom of the picture are
slightly cut off.
• The ZOOM mode may be
automatically changed by the control
signal from an external device. When
you want to return to the previous
ZOOM mode, choose the ZOOM
mode again.
14:9 ZOOM:
This zooms up the wide picture (14:9 aspect
ratio) to the upper and lower limits of the
screen.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
• When you set the CINEMA SURROUND
function to HIGH mode, there may be
slight volume distortion. If that occurs,
please switch to LOW mode. The effect
of CINEMA SURROUND functions will
be less noticeable, but the volume
„ Adjusting the visible area of the
picture
If subtitles or the top (or bottom) of the
picture are cut off, you can adjust the visible
area of the picture manually.
1 Press the c button
distortion will be corrected.
The ZOOM menu appears.
MONO:
Select the MONO mode, when you listen to
the mono sound.
You can enjoy the sound for a wider
audience similar to stereo sound.
2 Press the a button to display the
ZOOM mode indicator
The indicator appears.
16 : 9 ZOOM
OFF:
D0010-EN
The CINEMA SURROUND function
switches off.
3 While it is displayed, press the 6
buttons to change the position of
the picture
• You can choose the CINEMA
SURROUND mode with the “SOUND
menu” (see page 29).
• You cannot adjust the visible area in
REGULAR or FULL mode.
The visible area adjustment is saved even
after the TV channel is changed.
However, it is cancelled if the following
operations are performed.
Using the “Freeze” function
You can view the current programme as a
still picture.
• The power is turned off/on
• The ZOOM mode is changed
• The X (Multi) button, f (Freeze)
button, or g (Text) button is pressed
• The TV is switched between TV mode
and VIDEO mode
1 Set the PIP/TV/DVD switch to the
PIP position
When using the “Freeze” function, set the
PIP/TV/DVD switch to the PIP position.
2 Press the f button
The still picture of the current picture will
appear.
CINEMA SURROUND function
You can enjoy sounds with a wider
ambience.
current
programme
still picture
• This function does not work for the sound
from headphones.
D0056
Press the 2 button to select
one of CINEMA SURROUND modes
HIGH/LOW:
When you listen to stereo sound, please
select HIGH or LOW mode.
You can enjoy sound similar to the
experience at the theatre.
When you combine the functions of A.H.B.
and BBE, you can enjoy more powerful
sound.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
To cancel the “Freeze” function:
Press the f button, the 6
p buttons or the number buttons.
12-pictures multi:
Still
pictures
• The “Freeze” function does not work
while a sub-picture is displayed.
• The still picture cannot be output from
the TV.
• The “Freeze” function does not work
for picture of PC signal.
Moving
picture
D0058
• When set to 2-pictures multi, you can
view a TV picture and a picture from
an external device. You cannot view a
TV picture on more than one screen at
the same time.
• When 12-pictures multi is set, pictures
from external devices are not displayed.
• When set to 2-pictures multi, the main-
picture can be changed by pressing the
6 p buttons. The sub-
picture screen can be changed by
pressing the 6 buttons.
Using the “Multi-picture”
function
1 Set the PIP/TV/DVD switch to the
PIP position
When using the “Multi-picture” function,
set the PIP/TV/DVD switch to the PIP
position.
When set to 12-pictures multi and
there are more than 12 pictures, the
next or previous 12 screens can be
displayed by pressing the
2 Press the X button
The “Multi-picture” menu appears.
6 p buttons.
1
2
12
• When set to 2-pictures multi, the main-
picture sound from the TV speaker can
be changed to the sub-picture sound by
pressing the c button when the PIP/
TV/DVD switch is set to the PIP
position. (The speaker mark moves
from the main-picture to the sub-
picture.)
D0101
3 Press the 5 buttons to choose
the number of screens and then
press the a button
Choose to return to one screen.
1
D0102
The sound changes to the main-picture
sound if the c button is pressed again.
When the headphones are connected,
you can listen to the sound from the
side at which the headphones mark is
displayed. No sound comes from the
TV speaker.
Choose to change to 2-pictures multi.
2
D0103
Choose to change to 12-pictures multi.
12
D0104
• The pictures from VIDEO-1 (or
VIDEO-3) cannot be displayed in the
sub-picture when the VIDEO-1
SETTING (or VIDEO-3 SETTING) is
set to COMPONENT (see page 38).
• The “Multi-picture” function does not
work for a PC signal.
• When set to 12-pictures multi, press
the 7 buttons to choose the
screen you want to view and the press
the a button to display that picture
on the whole screen.
2-pictures multi:
Main-
picture
Sub-
picture
D0056
With 1125i and 750p signals, the screen is
split into two as shown below.
Main-
picture
Sub-
picture
D1056
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
• The BLUE BACK function does not
work when the “Multi-picture”
function is being used.
• The ZOOM function does not work
when the “Multi-picture” function is
being used.
• If you want to view the “Return Channel”
and another TV channel alternately, first
choose a channel other than the “Return
Channel”. And then press the
1 button to change the
channel to the “Return Channel” In this
way, you can view two channels
alternately by pressing the 1
button.
To return the “Multi-picture” to one
screen:
Press the X button, press the 5
buttons to choose one screen, and then
press the a button.
„ Return function
The TV temporarily memorises the TV
channel that was chosen right before the
current TV channel as the “Last Channel”.
By pressing the 1 button, you can
alternately view the current TV channel and
the “Last Channel”.
• Pressing the 4 button will
also return the display to one screen.
RETURN PLUS function and
Return function
If you want to view two channels alternately
by using the Return function, first choose one
TV channel and then choose the other TV
channel with the number buttons. If you
choose the TV channel without using the
number buttons, there are cases where a
channel other than the one you first chose is
registered as the “Last Channel”.
The 1 button has two functions;
the RETURN PLUS function and the Return
function. If a channel has been registered as
the “Return Channel”, the RETURN PLUS
function operates. If there is no setting for the
“Return Channel”, the Return function
operates.
„ RETURN PLUS
By registering a channel you frequently view
as the “Return Channel”, you can select that
channel at any time simply by pressing the
1 button.
To register a TV channel as the
“Return Channel”:
Choose the Programme number to which the
channel you want to register has been set,
and press the 1 button and hold
for more than 3 seconds continuously.
“RETURN PLUS PROGRAMMED!” is
displayed and the registration is completed.
To cancel a TV channel registered as
the “Return Channel”:
While viewing any TV channel, press the
1 button and hold for more than 3
seconds continuously. “RETURN PLUS
CANCELED!” is displayed and the
registration is cancelled.
• When you turn off the TV, the registration
for the “Return Channel” is cancelled.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Favourite channel function
(favourite) button
(PR 1 – PR 99) in the number buttons 1 to 4.
After registering, the channel can be called
by pressing the d (favourite) button and a
number button 1 to 4.
Then “FAVOURITE1-4?” appears.
2 Press one of the number buttons 1
to 4
„ Favourite channel registration
The called favourite channel appears on
the screen.
• If a number button in which no
channel is registered is pressed, “NO
MEMORY” appears on the screen.
1 In the normal screen, choose a TV
channel (PR 1 – PR 99) that you
want to register
For details, refer to “Choose a TV channel
and watch images from external devices”
on page 12.
„ Setting the picture effect
When a favourite channel has been chosen
with the d (favourite) button and number
buttons 1 to 4, picture effect settings can be
memorised for each favourite channel by
setting the picture effects in the PICTURE
menu (see page 25).
2 Press and hold the d (favourite)
button for three seconds or more
Then “SET 1-4?” appears on the screen.
The following items in the PICTURE menu
(see page 25) are memorised.
PICTURE MODE
BACK LIGHT
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
WHITE BALANCE
DIGITAL VNR
COLOUR SYSTEM
The last setting made for each item is
memorised.
3 Press one of the number buttons 1
to 4
The current channel is registered in the
pressed number button.
After “PROGRAMMED!” appears on the
screen, the favourite channel icon appears
at the top-right of the screen.
• If the channel you are trying to register
is already registered in one of the other
number buttons 1 to 4, “NOT
AVAILABLE” appears on the screen.
• Channels locked with the CHANNEL
GUARD function cannot be registered.
• If AUTO PROGRAM is performed,
the registered favourite channels are
reset.
• When you want to delete a favourite
channel, delete the set channel and set
contents with FAVOURITE SETTING
(see page 33) in the FEATURES menu.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control buttons and functions
Operating a JVC brand DVD
player
These buttons will operate a JVC brand DVD
player. Pressing a button that looks the same
as the device’s original remote control button
has the same effect as the original remote
control.
1 Set the PIP/TV/DVD switch to the
DVD position
When you are operating the DVD player,
set the switch to the DVD position.
• You can turn the DVD player on or off
with the # (standby) button.
• You can also press the H or
T button and display the
DVD disc menu screen, and then
operate by pressing the 7
buttons.
2 Press the DVD control button to
control your DVD player
• If your DVD player is not made by
JVC, these buttons will not work.
• Even if your device is made by JVC,
some of these buttons may not work,
depending on the device you are using.
You cannot turn the TV on or off when the
PIP/TV/DVD switch is set to the DVD
position.
When you turn the TV on or off, set the
PIP/TV/DVD switch to the TV position.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext function
4 Choose a teletext page by pressing
the 6 p buttons,
number buttons or colour buttons
To return to the TV mode:
Press the 4 button, b
button, or g (Text) button.
PIP/TV/
DVD
• If you have trouble receiving teletext
broadcasts, consult your local dealer or
the teletext station.
• The ZOOM function will not work in
the TV and text mode or Text mode.
• You cannot operate menus when
viewing a teletext programme.
• If characters on a teletext programme
do not appear properly, change the
TELETEXT LANGUAGE setting. For
details, see “TELETEXT
Basic operation
LANGUAGE” on page 39.
1 Choose a TV channel with a teletext
broadcast
2 Set the PIP/TV/DVD switch to the
TV position
Using the List Mode
You can store the numbers of your favourite
teletext pages in memory and call them up
quickly using the colour buttons.
„ To store the page numbers:
3 Press g (Text) button to display
the teletext
1 Press B button to go into the
List mode
Pressing g (Text) button changes the
mode as follows:
The page numbers you have stored are
displayed at the bottom of the screen.
TEXT
TEXT
---
---
TV mode
TV and text mode
TEXT
TEXT
---
---
D1043
Text mode
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext function
2 Press a colour button to choose a
position. Then press the number
buttons to enter the page number
Sub-page
Some teletext pages include sub-pages that
are automatically displayed.
1 Choose a teletext page that
includes sub-pages
Sub-page numbers that can be viewed are
automatically displayed at the top of the
screen.
3 Press and hold down the A (Store)
button
2 Press the 5 buttons to choose a
sub-page number
The four page numbers blink white to
show that they are stored in memory.
Reveal
„ To call up a stored page:
Some teletext pages include hidden text
(such as answers to a quiz).
You can display the hidden text.
1 Press the B button to enter the
List mode
Each time you press the E (Reveal)
button, text is hidden or revealed
2 Press a colour button having a
stored page
To exit the List mode:
Press the B button again.
Size
Hold
You can double the height of the teletext
display.
You can hold a teletext page on the screen for
as long as you want, even while several other
teletext pages are being received.
Press the F (Size) button
Press the C (Hold) button
Hold indication
To cancel the Hold function:
Press C (Hold) button again.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Teletext function
Index
You can return to the index page instantly.
Press the G (Index) button
Returns to page 100 or a previously specified
page.
Cancel
You can search for a teletext page while
watching TV.
1 Press the number button to enter a
page number, or press a colour
button
The TV searches for a teletext page.
2 Press H (Cancel) button
The TV programme appears. When the
TV finds the teletext page, its page
number appears in the upper left of the
screen.
3 Press H (Cancel) button to return
to a teletext page when the page
number is on the screen
• The TV mode cannot be resumed by
pressing the H (Cancel) button. To
return to the TV mode press
4 or b button.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
This TV has a number of functions you can
operate using menus. To use all your TV’s
functions, you need to understand the basic
menu operating techniques fully.
Types of menu
PICTURE menu
Choose to set the screen
settings.
D0106
D0107
D0108
Buttons used to operate the menus
SOUND menu
Choose to set the sound settings.
FEATURES menu
Choose to set the sleep timer
and child lock settings.
SET UP menu
Choose to edit the channels or
set the display language
settings.
D0109
• The menu will disappear after about
one minute if no operation is
performed.
Basic operation
1 Press the H button to display
The menu guide area can be made to appear
and disappear for some menus.
the menu bar
PICTURE
While the menu is displayed, press the
5 button to change between the
guide area being displayed and not displayed.
D0105-EN
2 Press the 5 buttons to choose
the menu you want to use and then
press the a button
>> 4:3 AUTO ASPECT
PANORAMIC
REGULAR
14:9 ZOOM
PICTURE
OK
D1105-EN
Chosen
menu
Chosen
menu name
D0017-EN
Guide area
3 Press the 6 buttons to choose
the item to be set, press the 5
buttons to set the item, and then
press the a button
>> 4:3 AUTO ASPECT
PANORAMIC
REGULAR
14:9 ZOOM
If there are sub-menus, use the 7
buttons to operate them.
D1017-EN
• Press the b button to return to
the previous menu.
• Press the 4 or H
button to exit from the menu.
• The guide area for some menus will still
be displayed even if the 5
button is pressed. This is not a fault.
• Some menu items may not be operated
or set depending on the TV status or
other menu item settings.
Menu items that cannot be operated or
set are displayed in grey in the menu
and cannot be chosen.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s menu
Operation with the buttons on the TV
You can also operate the menus using the
buttons on the front panel of the TV.
TV/VIDEO button
MENU/OK button
6 buttons
5 buttons
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
PICTURE
BACK LIGHT
STANDARD
PICTURE MODE
BACK LIGHT
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
WHITE BALANCE
FEATURES
You can adjust the back light.
2 :darker
3 : brighter
COOL
RESET
CONTRAST
OK
D0014-EN
You can adjust the picture contrast.
2 :lower
3 : higher
• While the PICTURE menu is displayed,
pressing the blue button will set the
BACK LIGHT, CONTRAST, BRIGHT,
SHARP, COLOUR, TINT settings to
their default settings.
• When watching the picture from VIDEO-
1 to VIDEO-3 or the PC, picture effect
settings can be memorised for each
external input by setting the picture
effects in the PICTURE menu.
The following items in the PICTURE
menu are memorised.
BRIGHT
You can adjust the picture brightness.
2 :darker
3 : brighter
SHARP
You can adjust the picture sharpness.
2 :softer
3 : sharper
PICTURE MODE
BACK LIGHT
CONTRAST
BRIGHT
COLOUR
You can adjust the picture colour.
2 :lighter
3 : deeper
SHARP
COLOUR
TINT
WHITE BALANCE
DIGITAL VNR
COLOUR SYSTEM
TINT
You can adjust the picture tint.
2 :reddish
3 : greenish
The last setting made for each item is
memorised.
• You can change the TINT setting (picture
hue) when the colour system is NTSC
3.58, or NTSC 4.43.
PICTURE MODE
You can choose one of three PICTURE
MODEs to adjust the picture settings
automatically.
WHITE BALANCE
You can select one of three WHITE
BALANCE modes (three tones of white) to
adjust the white balance of the picture. Since
white is the colour which is used as a
reference for all the other colours, changing
the WHITE BALANCE mode affects the
appearance of all the other colours on the
screen.
BRIGHT:
Heightens contrast and sharpness.
STANDARD:
Standardises picture adjustment.
SOFT:
Softens contrast and sharpness.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
COOL:
MIN:
A bluish white. Using this mode when
watching bright pictures allows you to enjoy
a more vivid and bright picture.
The level of the DIGITAL VNR effect is set
to the minimum. If you set the DIGITAL
VNR function to AUTO(LOW) but feel that
the sharpness of the original picture has not
been reproduced fully, change the setting
from AUTO(LOW) to MIN.
• The MIN setting is not suitable for low-
quality pictures which contain a lot of
noise.
MID:
The normal white colour.
WARM:
A reddish white. Using this mode when
watching films allows you to enjoy colours
that are characteristic of films.
MAX:
The level of the DIGITAL VNR effect is set
to the maximum. If you set the DIGITAL
VNR function to AUTO(HIGH) but still
notice some noise, change the setting from
AUTO(HIGH) to MAX.
• The MAX setting is not suitable for high-
quality pictures which contain very little
noise.
FEATURES
Choose FEATURES and press the a or 3
button to display the sub-menu.
> FEATURES
DIGITAL VNR
Super DigiPure
PULL DOWN
COLOUR MANAGEMENT
PICTURE MANAGEMENT
COLOUR SYSTEM
4:3 AUTO ASPECT
AUTO(LOW)
AUTO
AUTO
ON
ON
„ Super DigiPure
The Super DigiPure function uses the latest
in digital technology to give you a natural-
looking picture. The Super DigiPure function
includes the following two functions.
OK
D1015-EN
DigiPure function:
„ DIGITAL VNR
This function helps to create a natural-
looking picture by eliminating unnecessary
edges from high-contrast and crisp images.
For images with low-contrast, edges are
added to produce a sharper, more detailed
picture.
You can choose from the three DigiPure
function settings of AUTO, MIN and MAX.
• If you set the DigiPure effect too high on
a low-quality picture that contains a lot of
noise, this may actually make the noise
worse. We recommend you use the
AUTO setting if you can.
The DIGITAL VNR function cuts down the
amount of ‘noise’ (‘snow’ or interference) in
the original picture.
You can choose from the three DIGITAL
VNR function settings of AUTO, MIN and
MAX.
AUTO(LOW)/AUTO(HIGH):
The TV will automatically adjust the level of
the DIGITAL VNR effect to match the
amount of noise in the picture, giving you the
best possible picture.
• If you set the DIGITAL VNR effect too
high it can make the picture less sharp. It is
recommended you use the AUTO(LOW)
setting if you can. If you set the DIGITAL
VNR function to AUTO(LOW) but still
notice some noise, change the setting from
AUTO(LOW) to AUTO(HIGH).
Picture motion compensation
function:
This function displays fast-moving pictures
(for example, the players or ball in a football
game) more smoothly and naturally on the
screen.
• The effect level of the picture motion
compensation function cannot be
changed. The effect level is the same no
matter which of the AUTO, MIN or MAX
settings is used.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
„ COLOUR MANAGEMENT
AUTO:
The TV will automatically adjust the level of
the DigiPure effect to match the amount of
noise in the picture, giving the best possible
picture.
This TV supports the COLOUR
MANAGEMENT function to ensure dull
colours are compensated to produce natural
hues.
The COLOUR MANAGEMENT function is
on by default.
ON:
COLOUR MANAGEMENT function is
turned on.
OFF:
COLOUR MANAGEMENT function is
turned off.
MIN:
The level of DigiPure effect is set to the
minimum. When you set the Super DigiPure
function to AUTO and notice some noise,
change the setting from AUTO to MIN.
• The MIN setting is not suitable for high-
quality pictures which contain very little
noise.
MAX:
• Set this function to ON under normal
conditions.
The level of DigiPure effect is set to the
maximum. If you set the Super DigiPure
function to AUTO but feel that the original
picture quality has not been reproduced fully,
change the setting from AUTO to MAX.
• The MAX setting is not suitable for low-
quality pictures which contain a lot of
noise.
„ PICTURE MANAGEMENT
The PICTURE MANAGEMENT function
makes it easier to see the dark areas when a
picture has many dark areas, and makes it
easier to see the bright areas when a picture
has many bright areas.
OFF:
The Super DigiPure function is turned off.
Normally use with this function on.
ON:
„ PULL DOWN
PICTURE MANAGEMENT function is
turned on.
The PULL DOWN function displays a
cinema film picture more smoothly and
naturally on the screen.
OFF:
PICTURE MANAGEMENT function is
turned off.
AUTO:
The television automatically recognises the
type of signal and turns the function on and
off.
„ COLOUR SYSTEM
The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.
ON:
This function is turned on.
OFF:
This function is turned off.
1 Choose COLOUR SYSTEM. Then
press the a or 3 button
The sub-menu of the COLOUR SYSTEM
function appears.
>> COLOUR SYSTEM
MAIN
SUB
PAL
AUTO
OK
D0016-EN
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
For colour system in your country or
region, refer to the table below:
2 Press the 5 buttons to choose
MAIN or SUB
MAIN:
You can change the colour system of the
main-picture.
SUB:
You can change the colour system of the
sub-picture.
• Choose MAIN when a sub-picture is
not displayed.
Area
Country or Region
System
Bahrain, Kuwait, Oman,
Qatar, United Arab Emirates,
Yemen, etc.
Indonesia, Malaysia,
Singapore, Thailand, India,
etc.
PAL
Asia,
Middle
East
China, Vietnam, etc.
Hong Kong, etc.
PAL
PAL
Islamic Republic of Iran,
Lebanon, Saudi Arabia, etc.
SECAM
3 Press the 6 buttons to choose
the appropriate colour system.
Then press the a button
Philippines, Taiwan,
Myanmar, etc.
NTSC
Russia, etc.
SECAM
PAL:
PAL system
SECAM:
SECAM system
Czech Republic, Poland, etc. PAL
Europe
Germany, Holland, Belgium,
etc.
UK, etc.
PAL
PAL
Oceania Australia, New Zealand, etc. PAL
Republic of South Africa, etc. PAL
NTSC 3.58:
NTSC 3.58 MHz system
Africa Nigeria, etc.
Egypt, Morocco, etc.
PAL
SECAM
NTSC 4.43:
NTSC 4.43 MHz system
AUTO:
„ 4:3 AUTO ASPECT
This function detects a colour system
from the input signal.
You can choose one of three ZOOM modes,
REGULAR, PANORAMIC or 14:9 ZOOM,
as the ZOOM mode for the normal picture
(4:3 aspect ratio).
• The AUTO function may not function
properly if you have poor signal quality.
If the picture is abnormal in the AUTO
function, choose another colour system
manually.
1 Choose 4:3 AUTO ASPECT then
press the a button
>> 4:3 AUTO ASPECT
• COLOUR SYSTEM cannot be chosen
PANORAMIC
REGULAR
14:9 ZOOM
when you are watching the PC picture.
OK
D0017-EN
2 Press the 6 buttons to choose a
ZOOM mode
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND menu
SOUND
TREBLE
STEREO/
BASS
TREBLE
BALANCE
CINEMA SURROUND
You can adjust the high tone of the sound.
2 :weaker
3 : strong
OFF
OFF
OFF
A.H.B.
BBE
BALANCE
OK
You can adjust the volume balance between
the left and right speaker.
3 : turn the right speaker’s volume level up.
D0019-EN
• When the headphones are connected, only
“STEREO / I • II” can be used.
STEREO / I • II
CINEMA SURROUND
When you are viewing a bilingual broadcast
programme, you can choose the sound from
Bilingual I (Sub I) or Bilingual II (Sub II). If
you have poor reception on a stereo
broadcast, you can change from stereo to
mono sound so that you can hear the
broadcast more clearly and easily.
effect by using the CINEMA SURROUND
function.
• You can choose a CINEMA
SURROUND mode from HIGH, LOW,
MONO and OFF modes. For details, see
“CINEMA SURROUND function” on
page 15.
s: Stereo sound
• You can also operate the CINEMA
SURROUND function with the
2 button. For details, see
“CINEMA SURROUND function” on
page 15.
v : mono sound
t : Bilingual I (sub I)
u : Bilingual II (sub II)
• The sound mode you can choose differs
depending on the TV programme.
• This function does not work in the
VIDEO modes.
A.H.B. (Active Hyper Bass)
Used when you want to emphasise the bass
sound.
ON:
This function is turned on.
BASS
OFF:
You can adjust the low tone of the sound.
2 :weaker
3 : strong
This function is turned off.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND menu
BBE
BBE function restores clarity and presence
for better speech intelligibility and musical
realism.
ON:
This function is turned on.
OFF:
This function is turned off.
• Manufactured under license from BBE
Sound, Inc. Licensed by BBE Sound, Inc.
under USP4638258, 5510752 and
5736897. BBE and BBE symbol are
registered trademarks of BBE Sound, Inc.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES menu
To cancel the SLEEP TIMER
function:
Press the 2 button to set the period of
time to “OFF”.
FEATURES
SLEEP TIMER
CHANNEL GUARD
APPEARANCE
BLUE BACK
CHILD LOCK
TYPE A
ON
OFF
AUTO SHUTOFF
FAVOURITE SETTING
OFF
CHANNEL GUARD
When there is a TV channel you do not want
your children to watch, you can use the
CHANNEL GUARD function to lock out the
TV channel. Even when a child chooses a
programme number (PR) for a locked TV
channel the screen will change to blue and
display n (CHANNEL GUARD) so the TV
channel cannot be viewed. Unless you enter a
pre-set ID number by a special operation, the
lock cannot be released and the child cannot
view the TV channel.
OK
D0023-EN
SLEEP TIMER
You can set the TV to automatically turn off
after a set period of time.
1 Choose SLEEP TIMER. Then press
the a or 3 button
A Sub-menu of the SLEEP TIMER
function appears.
„ To set the CHANNEL GUARD
function
> SLEEP TIMER
1 Choose CHANNEL GUARD, then
press the 0 button
0
120
OFF
“SET ID NO.” (ID number setting screen)
appears.
OK
>> SET ID NO.
D0024-EN
0040
2 Press the 5 buttons to set the
period of time.
OK
Then press the a button
You can set the period of time for up to
120 minutes (2 hours) in 10 minute steps.
• One minute before the SLEEP TIMER
function turns off the TV, “GOOD
NIGHT!” appears.
• The SLEEP TIMER function cannot
be used to turn off the TV’s main
power.
D0025-EN
2 Set the ID number to your liking
1 Press the 6 buttons to choose
a number.
2 Press the 5 buttons to move
the cursor.
• When the SLEEP TIMER function is
on, you can display the sub-menu of
the SLEEP TIMER function again to
confirm or change the remaining
period of time of the SLEEP TIMER
function. Press the a button to leave
the menu after confirming or changing
the remaining time.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES menu
3 Press the a button
The Sub-menu of CHANNEL GUARD
appears.
2 Press the
button to
5
display “ID NO.” (ID No. input
screen)
> CHANNEL GUARD
5
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
ID NO.
:
CH
CH
CH
CH
CH
CH
CC
CC
CC
21
22
23
24
25
26
01
02
03
D0028-EN
3 Press the number buttons to enter
the ID number
The lock is temporarily released so you
can view the TV channel.
GUARD
OK
If you have forgotten the ID
number:
D1026-EN
Perform step 1 of “To set the CHANNEL
GUARD function”. After confirming the
to exit the menu.
4 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the
Programme number (PR) changes, and the
picture of the TV channel registered in the
Programme number (PR) is displayed on
the screen.
• Even if you reset the lock temporarily,
it does not mean that the CHANNEL
GUARD function set for the TV
channel is cancelled. The next time
anyone tries to view the TV channel, it
will be locked again.
5 Press the blue button and set the
CHANNEL GUARD function.
Then press the a button
• When you want to cancel the
n (CHANNEL GUARD) appears and the
TV channel is locked.
CHANNEL GUARD function, you
must perform the operation “To set the
CHANNEL GUARD function” again.
• To stop it being easy to choose the
programme number (PR) of a locked
TV channel, the programme number
(PR) has been set so that it cannot be
chosen with the 6 buttons or the
buttons of the TV.
To reset the CHANNEL GUARD
function:
Press the blue button again.
n (CHANNEL GUARD) disappears.
To disable easy resetting of the
CHANNEL GUARD function, the menu
disappears if you choose the CHANNEL
GUARD function and press the a
button.
• To stop it being easy to reset the lock,
“ID NO.” (ID No. input screen) is set
so that it cannot appear unless you
press the
button.
5
„ To view a locked TV channel
1 Choose a programme number (PR)
of a locked TV channel with the
number buttons or PR LIST
The screen changes to blue and the n
(CHANNEL GUARD) appears. You
cannot view the TV channel.
5
D0027
32
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES menu
APPEARANCE
AUTO SHUTOFF
Press the 5 button and choose the format
in which the channel number is displayed
from the four types: TYPE A, TYPE B,
TYPE C, and TYPE D.
You can set the power to turn off if no signal
is received and no operation is performed for
about 15 minutes or longer after the end of a
broadcast.
ON:
• Set to TYPE D when shipped from
factory. TYPE D sets all screens to
semitransparent.
The menu screens are not semitransparent
when set to a type other than TYPE D.
This function is turned on.
OFF:
This function is turned off.
• The AUTO SHUTOFF function does not
turn off the TV’s main power.
• The AUTO SHUTOFF function does not
work for the VIDEO mode or a picture
from a PC signal.
BLUE BACK
You can set the TV to automatically change
to a blue screen and mute the sound if the
signal is weak or absent, or when there is no
input from an external device.
FAVOURITE SETTING
Chose when deleting the favourite channels
registered in the buttons 1 to 4.
ON:
This function is turned on.
1 Choose FAVOURITE SETTING,
then press the a or 3 button
The FAVOURITE SETTING menu
appears.
OFF:
This function is turned off.
CHILD LOCK
FAVOURITE SETTING
You can disable the front control buttons of
the TV. When this function is set to ON, the
TV can be operated only by using the remote
control.
Use this function to prevent children from
operating the TV at their own discretion
(without parent consent).
1
2
3
4
PR 01
PR 02
PR 03
PR 04
RESET
OK
ON:
D0112-EN
This function is turned on.
OFF:
2 Press the 6 buttons and chose
the favourite channel that you want
to delete
This function is turned off.
When you disconnect the AC plug, the
CHILD LOCK will be cancelled.
3 Press the blue button
The chosen favourite channel and set
contents are deleted.
• For details of the favourite channels, see
“Favourite channel function” on page 18.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
• You can proceed to edit the
programme numbers list using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL” on page 34.
• If a TV channel you want to view is
not stored in the programme numbers
list, you can register it using the
MANUAL function.
SET UP
AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
VIDEO-1 SETTING
VIDEO-3 SETTING
AI VOLUME
VIDEO
OFF
TELETEXT LANGUAGE
OK
For details, see “EDIT/MANUAL” on
page 34.
D0029-EN
• The AUTO PROGRAM function does
not store a TV channel to the
programme number PR 0 (AV).
• If you do not need to use the EDIT/
MANUAL function, press the a
button to exit the EDIT menu.
• Starting the AUTO PROGRAM
deletes the registered favourite
channel.
AUTO PROGRAM
You can again perform the AUTO
PROGRAM function TV channel automatic
registration which was performed in the
“Initial settings (Setup tour)” (page 8).
1 Choose AUTO PROGRAM, then
press the a or 3 button
The AUTO PROGRAM function starts.
The TV channels you receive are
automatically stored in the programme
numbers list.
EDIT/MANUAL
The EDIT/MANUAL functions are divided
into two types:
>> AUTO PROGRAM
• editing the current programme numbers
(PR) (EDIT functions); and
CH 28
14%
• manually storing a TV channel you want
to view on a particular programme
number (PR) (MANUAL function).
OK
Here are the details about these functions:
D0004-EN
MOVE:
• To stop the AUTO PROGRAM
This function changes the programme
number (PR) of a TV channel.
function, press the a button.
2 After the TV channels have been
stored in the programme number
list, the EDIT menu appears
ID:
This function registers a channel name (ID)
to a TV channel.
INSERT:
> EDIT
This function adds a new TV channel in the
current programme numbers (PR) list by
using the CH/CC number.
• You cannot use the INSERT function if
you do not know the channel number of a
TV channel. Use the MANUAL function
to register a TV channel in the programme
number (PR).
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
CH
CH
CH
CH
CH
CH
CC
CC
CC
21
22
23
24
25
26
01
02
03
ID
MANUAL
OK
MOVE
INSERT DELETE
D0038-EN
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
DELETE:
This function deletes a TV channel you do
not want to list.
3 Press the a button to complete
the settings
MANUAL:
This function manually stores a new TV
channel in a programme number (PR).
• For programme number PR 0, “AV”
appears in the programme numbers (PR)
list.
• A VIDEO terminal number does not
appear in the programme numbers (PR)
list.
Caution
• Using the MOVE, DELETE or INSERT
functions rewrites the current
programme numbers (PR) list.
Therefore, the programme numbers
(PR) of some of the TV channels will
change.
• Using the MANUAL function for a TV
channel for which the CHANNEL
GUARD function has been set cancels
the CHANNEL GUARD function for
that channel.
• The CH/CC number is a number unique to
the TV and corresponds to the channel
number of a TV channel. For the
relationship between a channel number
and a CH/CC number, see “CH/CC
numbers” on page 44.
„ MOVE
• When a TV channel has already been
registered in PR 99, using the INSERT
function deletes that TV channel.
1 Press the 6 buttons to choose a
TV channel
2 Press the 3 button to start the
„ Basic operation
MOVE function
1 Choose EDIT/MANUAL, then press
the a or 3 button
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
The EDIT menu appears.
CH 21
CH
CH
CH
CH
CH
CC
CC
CC
22
23
24
25
26
01
02
03
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
CH
CH
CH
CH
CH
CH
CC
CC
CC
21
22
23
24
25
26
01
02
03
OK
STORE
D0030-EN
ID
MANUAL
OK
MOVE
3 Press the 6 buttons to choose a
INSERT DELETE
D0038-EN
new programme number (PR)
To cancel the MOVE function:
Press the b button.
2 Follow the description for the
function you want to use
4 Press the 2 button to change the
programme number (PR) of a TV
channel to a new programme
number (PR)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
„ DELETE
„ INSERT
1 Press the 6 buttons to choose a
1 Press the 6 buttons to choose a
programme number (PR) for which
you will register a new TV channel
TV channel
2 Press the yellow button to delete
the TV channel
2 Press the green button and start
the INSERT function
The TV channel is deleted from the
programme numbers (PR) list.
> EDIT
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
„ ID
CH
CH
CH
CH
CH
CH
CC
CC
CC
21
22
23
24
25
26
1 Press the 6 buttons to choose a
TV channel
02
03
2 Press the red button to start the ID
function
OK
0
9
CH/CC
D0034-EN
3 Enter a channel name (ID). Press
the 6 buttons to choose a
character. Press the 5 buttons to
move the cursor
3 Press the 6 buttons to choose
“CC” or “CH” according to the CH/
CC number of the TV channel
> EDIT
To cancel the INSERT function:
Press the b button.
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
CH
CH
CH
CH
CH
CH
CC
CC
CC
21
22
23
24
25
26
01
02
03
4 Press the number buttons to enter
the remaining CH/CC number
M
The TV shifts to registration mode. When
the registration is completed, the picture
of the TV channel appears on the screen.
OK
D0032-EN
• The CH/CC number is a number given
to each broadcast frequency that
carries a TV channel. If the TV cannot
detect the TV channel corresponding
to the broadcast frequency indicated
by the CH/CC number, a “no-signal”
picture appears.
To cancel the ID function:
Press the b button.
4 Press the a button to give a
channel name to a TV channel
Before performing INSERT operation
• A CH/CC number unique to this TV and
corresponding to the Channel number of a
TV channel is required. Find the
corresponding CH/CC number from a
table “CH/CC numbers” on page 44 based
on the Channel number of the TV
channel.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
4 Press the green or red button to
„ MANUAL
search for a TV channel
Scanning stops when the TV finds a TV
channel. Then the TV channel is
displayed.
1 Press the 6 buttons to choose a
programme number (PR) for a new
TV channel
2 Press the blue button to activate
the MANUAL function
5 Press the green or red button
repeatedly until the TV channel you
want appears
At the right side following the CH/CC
number, the SYSTEM (sound system) of
the TV channel appears.
If the TV channel reception is poor:
Press the blue or yellow button to fine-
tune the TV channel.
> MANUAL
PR
AV
01
02
03
04
05
06
07
08
09
ID
CH/CC
CH
CH
CH
CH
CH
CH
CC
CC
CC
21
22
23
24
25
26
If you cannot hear the normal
sound even when the picture of the
TV channel appears normally:
The SYSTEM setting is wrong. Press the
3 button and choose a SYSTEM that has
normal sound.
(
01 B / G
)
02
03
SEARCH+
FINE-
OK
SYSTEM
FINE+
SEARCH-
D0035-EN
6 Press the a button and register
the TV channel to a Programme
number (PR)
To cancel the MANUAL function:
Press the b button.
The normal EDIT menu is resumed.
3 Press the 3 button to choose the
SYSTEM (sound system) for a TV
channel you want to register
• For the sound systems in each country
or region, refer to the table below:
Area
Country or Region
System
Bahrain, Kuwait, Oman,
Qatar, United Arab Emirates,
Yemen, etc.
Indonesia, Malaysia,
Singapore, Thailand, India,
etc.
B/G
Asia,
Middle
East
China, Vietnam, etc.
Hong Kong, etc.
D/K
I
Islamic Republic of Iran,
Lebanon, Saudi Arabia, etc.
B/G
Philippines, Taiwan,
Myanmar, etc.
M
Russia, etc.
D/K
Czech Republic, Poland, etc. D/K
Europe
Germany, Holland, Belgium,
etc.
B/G
UK, etc.
I
Oceania Australia, New Zealand, etc. B/G
Republic of South Africa, etc. I
Africa Nigeria, etc.
Egypt, Morocco, etc.
B/G
B/G
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
LANGUAGE
AI VOLUME
The LANGUAGE setting which was
performed in the “Initial settings (Setup
tour)” (page 8) can be changed.
You can prevent the sudden increase or
decrease of sound that occurs when changing
the channel to another channel.
ON:
1 Choose LANGUAGE, then press
the a or 3 button
This function is turned on.
A sub-menu of the LANGUAGE function
appears.
OFF:
This function is turned off.
• The AI VOLUME function may not
operate as expected if the sound input
level from a broadcast station is extremely
low.
LANGUAGE
• This function does not work in the
VIDEO mode.
D1002-EN
2 Press the 6 buttons to choose a
language. Then press the a
button
VIDEO-1 SETTING/VIDEO-3
SETTING
Set the VIDEO-1 SETTING or VIDEO-3
SETTING correctly according to the video
connected to the VIDEO-1 or VIDEO-3
terminal. If this setting is incorrect, images
will not be displayed.
VIDEO:
If a normal video signal (composite video
signal) is input.
COMPONENT:
If a Component video signal (Y, Cb/Pb, Cr/
Pr signals) is input.
• For detailed connecting methods, see
“Additional preparation” on page 41. This
Television is compatible with the 1125i,
625p or 525p video signal only when the
component video signal is input.
• When the input signal is 1125i, 625p or
525p, each signal type is displayed at the
upper right side on the TV screen by
setting the input to VIDEO-1 or VIDEO-3.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP menu
TELETEXT LANGUAGE
There are four types of teletext language
groups. Set the teletext language group that
corresponds to the language of the teletext
programme that you want to watch.
1 Choose TELETEXT LANGUAGE,
then press the a or 3 button
> TELETEXT LANGUAGE
GROUP-1
GROUP-2
GROUP-3
GROUP-4
OK
D1003-EN
2 Press the 6 buttons to choose a
group
Group
Languages
GROUP-1
Turkish, Hungarian, English,
German, French, Italian, Spanish,
Portuguese, Greek, Swedish,
Finnish
GROUP-2
GROUP-3
GROUP-4
Polish, Serbian, Croatian,
Slovenian, Czech, Slovak,
Rumanian, Hungarian, German,
French, Italian, Swedish, Finnish
Russian, Bulgarian, Lettish,
Lithuanian, Estonian, Ukrainian,
Serbian, Croatian, Slovenian,
Czech, Slovak, English, German
Arabic, Czech, Slovak. Hungarian,
English, German, French, Italian,
Spanish, Portuguese, Swedish,
Finnish
3 Press the a button to complete
the setting
The menu disappears.
• Languages that are not included in the
teletext language group that you select,
the sub-titles of the teletext programme
will not be displayed properly.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying a computer screen
This TV can be used as a computer screen.
Watching images from a
computer
Connecting to the computer
Use a D-SUB cable to connect the TV’s PC
IN terminal to the computer’s analogue RGB
output terminal.
If you want to listen to the sound from the
computer, use an audio cable to connect the
VIDEO-3 AUDIO L/R sound input terminal
to the computer’s sound output terminal.
When the sound from the computer is mono,
connect to the VIDEO-3 AUDIO L terminal.
After starting the computer, press the
4 or 6 p buttons
to choose “PC”
You can listen to the sound when the
sound from the computer is connected to
the VIDEO-3 AUDIO L/R sound input
terminal.
• When the sound from the computer is
connected to VIDEO-3, by choosing
external input VIDEO-3 the sound
from the computer can be listened to,
but the images from the computer
cannot be seen.
IN
Table of signals for each type
of computer
Resolution
Vertical
frequency
(Hz)
Horizontal
frequency
(kHz)
640 × 480
(VGA)
60.0
31.5
1024 × 768
(XGA)
60.0
42.0
* Only the above formats are supported.
* Even with the above formats and at
60 Hz, some problems may be
experienced depending on the quality of
the synchronous signal. (Depending on
the quality, some pictures may not be
displayed properly.)
* Apple Macintosh computers are not
supported.
When a picture is not displayed
Check the computer’s refresh rate and set it
to 60 Hz. Refer to the computer’s instruction
manual.
Computers which cannot have their refresh
rate set to 60 Hz cannot be used with this
unit.
• Refer to the computer manual for a
detailed explanation of the connections at
the computer side.
• Ensure that the connectors are facing the
correct way when connecting.
• After connecting the D-SUB cable,
tighten the two screws to fix the connector
in place.
*
* Apple Macintosh is a registered
trademark of Apple Computer, Inc.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
Connecting external equipment
Connect the equipment to the TV, making
the correct rear panel and front panel
connections.
1 VCR (composite signal)
2 VCR (S-VIDEO signal; Y/C)
3 VCR for recording (composite signal)
4 DVD player (composite signal)
5 DVD player (S-VIDEO signal; Y/C)
6 TV game (composite signal)
7 TV game (S-VIDEO signal; Y/C)
8 Headphones
9 Camcorder (composite signal/S-VIDEO
signal; Y/C)
0 DVD player (component video signals; Y,
Pb/Cb, Pr/Cr)
Before connecting anything:
• Read the manuals that came with the
equipment.
Depending on the equipment, the
connection method may be different from
the diagram. Also, the equipment settings
may need to change depending on the
connection method.
• Turn off all the equipment including the TV.
• The “Specifications” on page 47 give the
details of the VIDEO terminals. If you are
connecting equipment not listed in the
table to choose the best VIDEO terminal.
• Connecting cables are not supplied.
• If the VCR’s audio output is in mono,
connect the VCR’s AUDIO OUT (audio
output) terminal and the TV’s VIDEO-3
AUDIO L terminal with an audio cable.
• Use the supplied cable to connect the
component device to the VIDEO-1
COMPONENT Y Pb/Cb Pr/Cr terminal.
- Video cable
~ S-VIDEO cable
! Component cable
„ Connecting the PC
For details, see “Connecting to the computer”
on page 40.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
OUT
OUT
Supplied cable
(Component video cable)
IN
IN
without terminal covers
IN
OUT
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional preparation
„ Connecting headphones
Connect the headphones with a stereo mini-
jack (3.5 mm diameter) to the headphone
jack.
without terminal covers
• No sound comes from the TV speakers
when the headphones are connected.
IN
„ TV output from the OUT terminal
The video/sound signal of a TV channel you
are viewing is always output from the OUT
terminal.
• No signal will output through the S VIDEO
terminal when you are not viewing images
coming from the S VIDEO input. In this
case, use the VIDEO terminal instead of
the S VIDEO terminal.
R
L
• Changing over a programme number (PR)
also changes over the TV output from the
OUT terminal.
IN
• When using the VIDEO-1 COMPONENT
Y Pb/Cb Pr/Cr terminal input, VIDEO-3
COMPONENT input or PC IN input, the
sound signal is output from the OUT
terminal but the picture signal is not
output.
1
2
Amplifier
External speakers (Magnetic-shielded type)
• Teletext programmes cannot be output.
• The output from the OUT terminal is not
interrupted by headphone connection to
the TV. You cannot cut the sound from
the front speaker even if you connect a
headphone to the TV.
„ Connecting speakers/amplifier
While referring to the audio equipment
connection diagram, connect the audio
equipment you want to the TV.
You can use external front speakers to listen
to the TV sound instead of the TV speakers.
• Adjust the volume of the external
speakers with the amplifier.
Before connecting anything:
• Read the manuals provided with the
amplifier and speakers.
• Turn the TV and amplifier off.
• To prevent magnetism from the speakers
adversely effecting the TV screen, use
magnetic-shielded speakers for the front
speakers.
• Note that connecting cables are not
supplied.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
CH/CC numbers
When you want to use the INSERT function on page 36, find the CH/CC number corresponding to
the Channel number of the TV channel from this table.
US:
The US channel numbers are the channel numbers used in the United States,
Philippines, etc.
CCIR:
OIRT:
The CCIR channel numbers are the channel numbers used in the Middle East,
Southeast Asia, etc.
The OIRT channel numbers are the channel numbers used in Eastern Europe, Russia,
Vietnam, etc.
AUSTRALIA: The AUSTRALIA channel numbers are the channel numbers used in Australia, etc.
Channel
Channel
CH
US
CCIR
OIRT
AUSTRALIA
AU-0
CC
US
CCIR
OIRT
AUSTRALIA
AU-5
CH02
CH03
CH04
CH05
CH06
CH07
CH08
CH09
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH17
CH18
CH19
CH20
CH21
CH22
CH23
CH24
CH25
CH26
CH27
CH28
CH29
CH30
CH31
CH32
CH33
CH34
CH35
CH36
CH37
CH38
CH39
CH40
CH41
CH42
CH43
CH44
CH45
CH46
CH47
CH48
CH49
CH50
CH51
CH52
CH53
CH54
CH55
CH56
CH57
CH58
CH59
CH60
CH61
CH62
CH63
CH64
CH65
CH66
CH67
CH68
CH69
US-2
US-3
US-4
US-5
US-6
US-7
US-8
US-9
US-10
US-11
US-12
US-13
E2
E3
E4
E5
E6
E7
E8
E9
R1
CC01
CC02
CC03
CC04
CC05
CC06
CC07
CC08
CC09
CC10
CC11
CC12
CC13
CC14
CC15
CC16
CC17
CC18
CC19
CC20
CC21
CC22
CC23
CC24
CC25
CC26
CC27
CC28
CC29
CC30
CC31
CC32
CC33
CC34
CC35
CC36
CC37
CC38
CC39
CC40
CC41
CC42
CC43
CC44
CC45
CC46
CC47
CC48
CC49
CC50
CC51
CC52
CC53
CC54
CC55
CC56
CC57
CC58
CC59
CC60
CC61
CC62
CC63
CC64
CC75
CC76
CC77
CC78
CC79
CC95
CC96
CC97
CC98
CC99
S-1
S-2
S-3
S-4
S-5
S-6
S-7
S-8
AU-1
AU-2
AU-6
AU-7
AU-8
AU-9
R2
R6
R7
R8
R9
AU-5A
E10
E11
E12
R10
R11
R12
AU-10
AU-11
S-9
S-10
S-11
S-12
S-13
S-14
S-15
S-16
S-17
S-18
S-19
S-20
S-21
S-22
S-23
S-24
S-25
S-26
S-27
S-28
S-29
S-30
S-31
S-32
S-33
S-34
S-35
S-36
S-37
S-38
S-39
S-40
S-41
US-14, W+29
US-15, W+30
US-16, W+31
US-17, W+32
US-18, W+33
US-19, W+34
US-20, W+35
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
W+10
W+11
W+12
W+13
W+14
W+15
W+16
W+17
W+18
W+19
W+20
W+21
W+22
W+23
W+24
W+25
W+26
W+27
W+28
US-21, W+36 E21
US-22, W+37 E22
US-23, W+38 E23
US-24, W+39 E24
US-25, W+40 E25
US-26, W+41 E26
US-27, W+42 E27
US-28, W+43 E28
US-29, W+44 E29
US-30, W+45 E30
US-31, W+46 E31
US-32, W+47 E32
US-33, W+48 E33
US-34, W+49 E34
US-35, W+50 E35
US-36, W+51 E36
US-37, W+52 E37
US-38, W+53 E38
US-39, W+54 E39
US-40, W+55 E40
US-41, W+56 E41
US-42, W+57 E42
US-43, W+58 E43
US-44, W+59 E44
US-45, W+60 E45
US-46, W+61 E46
US-47, W+62 E47
US-48, W+63 E48
US-49, W+64 E49
US-50, W+65 E50
US-51, W+66 E51
US-52, W+67 E52
US-53, W+68 E53
US-54, W+69 E54
US-55, W+70 E55
US-56, W+71 E56
US-57, W+72 E57
US-58, W+73 E58
US-59, W+74 E59
US-60, W+75 E60
US-61, W+76 E61
US-62, W+77 E62
US-63, W+78 E63
US-64, W+79 E64
US-65, W+80 E65
US-66, W+81 E66
US-67, W+82 E67
US-68, W+83 E68
US-69, W+84 E69
X
Y
Z
Z+1
Z+2
R3
R4
R5
AU-3
AU-4
A-5
A-4
A-3
A-2
A-1
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If a problem arises while you are using the TV, please read this troubleshooting guide carefully
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may
think there is a problem with the TV itself.
Important:
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you
have a question when you are operating a function, read the page(s) for that function carefully,
not this troubleshooting guide.
• If you follow the advice in this troubleshooting guide without any success, unplug the mains
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to
remove the rear cover of the TV.
– Have the TV and aerial been connected
properly?
– Has the aerial cable been damaged?
– Is the aerial pointing in the right
direction?
„ If you cannot turn on the TV
• Is the mains plug connected to the mains
outlet?
• Make sure you set the PIP/TV/DVD
switch to the TV position. You cannot
turn the TV on when the PIP/TV/DVD
switch is set to the DVD position.
– Is the aerial itself faulty?
• If the TV or aerial suffers interference
from other equipment, stripes or noise
may appear in the picture. Move any
equipment such as an amplifier, personal
computer, or a hair drier, that can cause
interference away from your TV. Or try
moving the TV. If the aerial suffers
interference from a radio tower or high-
dealer.
• If the TV suffers interference from signals
reflecting from mountains or buildings,
double-pictures (ghosting) will occur. Try
to change the aerial’s direction or replace
it with one with better directionality.
• Are your COLOUR SYSTEM settings
correct? Follow the description
„ If you cannot turn off the TV
switch to the TV position. You cannot
turn the TV off when the PIP/TV/DVD
switch is set to the DVD position.
• Have you chosen a TV channel with very
poor reception? If so, the BLUE BACK
function will be activated: the entire
screen becomes blue, and the sound is
muted. If you still want to view the TV
channel, follow the description “BLUE
BACK” on page 33 to change the BLUE
BACK function setting to OFF.
• If the SYSTEM setting for a TV channel
is incorrect, it may prevent the sound
from being issued. Follow the description
“EDIT/MANUAL” on page 34 to use the
MANUAL function to try to change the
SYSTEM setting.
“COLOUR SYSTEM” on page 27 to try
to solve the trouble.
• Have the COLOUR and BRIGHT settings
been adjusted properly? Follow the
description “BRIGHT” and “COLOUR”
on page 25 to try to adjust them properly.
• Videotaping teletext is not recommended
because it may not record correctly.
„ Poor picture
• If noise (snow) totally blocks out the
picture, there may be a problem with the
aerial or aerial cable. Check the following
to try to solve the problem:
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
• When viewing images from commercially
available video software products, or
videos from videotapes which have been
recorded improperly, the top of the image
may be distorted. This is due to the
condition of the video signal. There is
nothing wrong with the TV.
• Since this TV is designed to make full use
of the resolution of the original video
source, the motion may appear unnatural
when the video source is input with
progressive-scanning component signals.
If this occurs, change the output setting of
the connected device to interlace-
„ Other issues
• If the CHILD LOCK function set to ON,
you cannot operate the TV with the front
control buttons of the TV. Set the CHILD
LOCK function to OFF.
• When the SLEEP TIMER function or
AUTO SHUTOFF function operates, the
TV is automatically turned off. If the TV
suddenly turns off, try to press the #
(standby) button to turn on the TV once
again. If the TV goes back to normal,
there is no problem.
• When the TV is receiving a wide-screen
device affecting the screen size, the
ZOOM mode automatically changes.
When you want to resume the previous
ZOOM mode, press the c button
again.
scanning component signal output. See
the instructions that came with the device
for more information.
„ Poor sound
• Have you adjusted BASS or TREBLE
properly? If not, follow the description
“BASS” or “TREBLE” on page 29.
be hard to hear stereo or bilingual sound.
In this case, follow the description
“STEREO / I • II” on page 29 to hear the
sound more easily by changing it to a
mono sound.
• It takes a short period of time from the
channels is performed until an image is
displayed. This is not a fault. This is the
time needed for the image to stabilise
before it can be displayed.
• The TV may make a crackling sound due
to a sudden change in temperature. The
picture or sound may be normal. If you
hear crackling sounds frequently while
you are viewing the TV, there may be
other causes. As a precaution, ask your
service technician to inspect it.
• The top of the TV and the screen may
become hot during use but this has no
affect on the performance of the TV.
Make sure that the ventilation holes are
not blocked.
• When the picture is unstable, the screen
may become white for a moment. This
happens when the signal which drives the
liquid crystal is missing. This is not a
fault.
„ If the TV does not respond to the
remote control
• Have the batteries of the remote control
worn out? Follow the description “Putting
the batteries into the remote control” on
page 8 and replace them with new batteries.
• Have you attempted to use the remote
control from the sides or rear of the TV or
from more than seven metres away from the
TV? Use the remote control in front of your
TV or from less than seven metres away.
• When you are viewing a teletext
programme, you cannot operate the
• When a still image has been displayed for
a long period, a faint residual image may
remain on the screen for a short time after
the power has been turned off or when
another image is displayed. This is not a
fault and the image will eventually
disappear.
menus. Press the 4 button to
return to the ordinary TV programme, and
then try operating the menus.
• If the TV suddenly stops responding,
disconnect the power cord of the TV from
the AC outlet. Connect them to the AC
outlet again to turn on the TV. If the TV
returns to a normal state, it is not a failure.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
LT-Z32SX4B/LT-Z32SX4S
Broadcasting systems
Colour systems
B, G, I, D, K, K1, M
PAL, SECAM, NTSC 3.58/4.43 MHz
Channels and frequencies
VHF low channel (VL) = 46.25 to 168.25 MHz
VHF high channel (VH) = 175.25 to 463.25 MHz
UHF channel (U) = 471.25 to 863.25 MHz
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11
to S20) and hyper band (S21 to S41).
Sound-multiplex systems
NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system
Languages displayed by
teletext
Please see the table in the description “TELETEXT LANGUAGE” on page 39.
Teletext systems
Power requirements
Power consumption
Screen size
Audio output
Speakers
FLOF (Fastext), TOP, WST (World Standard System)
110 - 240 V AC, 50/60 Hz
161 W (Standby: 2.8 W)
Viewable area 80 cm (measured diagonally)
Rated Power output: 10 W + 10 W
6.6 cm round × 4
VIDEO-1 terminal
(COMPONENT)
RCA connector × 3, S VIDEO connector × 1, Component connector × 1
• Video input, S VIDEO (Y/C) input, Component video (Y, Cb/Pb, Cr/Pr) input
and Audio L/R inputs are available.
• 625p, 525p and 1125i signals are available.
VIDEO-2 terminal
RCA connector × 3, S VIDEO connector × 1
• Video input, S VIDEO (Y/C) input and Audio L/R inputs are available.
VIDEO-3 terminal
(COMPONENT)
RCA connector × 3
• Video input, Component video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are
available.
• 625p, 525p and 1125i signals are available.
OUT terminal
PC IN terminal
RCA connectors × 3, S VIDEO connector × 1
• Video output, S VIDEO (Y/C) output and Audio L/R outputs are available.
• Output level 0.5 Vrms.
Analogue RGB D-SUB (15 pin) × 1
• PC signal is available. Refer to page 40 for details of the signals which can be
input.
Headphone jack
Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D)
834 mm × 632 mm × 300 mm
834 mm × 568 mm × 108 mm (without stand)
Weight
20.6 kg
17.3 kg (without stand)
Accessories
Remote control unit × 1 (RM-C1830)
AA/R6 dry cell battery × 2
Component video cable × 1
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of
the owners of copyright of the original picture sources, as this would be an infringement of
copyright.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
LT-Z26SX4B/LT-Z26SX4S
Broadcasting systems
Colour systems
B, G, I, D, K, K1, M
PAL, SECAM, NTSC 3.58/4.43 MHz
Channels and frequencies
VHF low channel (VL) = 46.25 to 168.25 MHz
VHF high channel (VH) = 175.25 to 463.25 MHz
UHF channel (U) = 471.25 to 863.25 MHz
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11
to S20) and hyper band (S21 to S41).
Sound-multiplex systems
NICAM (B/G, I, D/K) system, A2 (B/G, D/K) system
Languages displayed by
teletext
Please see the table in the description “TELETEXT LANGUAGE” on page 39.
Teletext systems
Power requirements
Power consumption
Screen size
Audio output
Speakers
FLOF (Fastext), TOP, WST (World Standard System)
110 - 240 V AC, 50/60 Hz
125 W (Standby: 2.8 W)
Viewable area 64.8 cm (measured diagonally)
Rated Power output: 10 W + 10 W
6.6 cm round × 4
VIDEO-1 terminal
(COMPONENT)
RCA connector × 3, S VIDEO connector × 1, Component connector × 1
• Video input, S VIDEO (Y/C) input, Component video (Y, Cb/Pb, Cr/Pr) input
and Audio L/R inputs are available.
• 625p, 525p and 1125i signals are available.
VIDEO-2 terminal
RCA connector × 3, S VIDEO connector × 1
• Video input, S VIDEO (Y/C) input and Audio L/R inputs are available.
VIDEO-3 terminal
(COMPONENT)
RCA connector × 3
• Video input, Component video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are
available.
• 625p, 525p and 1125i signals are available.
OUT terminal
PC IN terminal
RCA connectors × 3, S VIDEO connector × 1
• Video output, S VIDEO (Y/C) output and Audio L/R outputs are available.
• Output level 0.5 Vrms.
Analogue RGB D-SUB (15 pin) × 1
• PC signal is available. Refer to page 40 for details of the signals which can be
input.
Headphone jack
Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D)
703 mm × 555 mm × 300 mm
703 mm × 491 mm × 107 mm (without stand)
Weight
16.1 kg
12.8 kg (without stand)
Accessories
Remote control unit × 1 (RM-C1830)
AA/R6 dry cell battery × 2
Component video cable × 1
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of
the owners of copyright of the original picture sources, as this would be an infringement of
copyright.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2004 Victor Company of Japan, Limited
0904MKH-CR-VP
Download from Www.Somanuals.com. All Manuals Search And Download.
|