JVC DVD VCR Combo LPT0674 001B User Manual

DVD/CD PLAYER

Hi-Fi STEREO

VIDEO CASETTE

RECORDER

USER'S GUIDE

For model:

HR-XVC1U

POWER

VCR

DVD

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

POWER

INPUT

TV VOL

TIMER

TV/VCR

PLAY

STOP

SKIP

/INDEX

SET

ENTER/

SELECT

SET

SET UP

CANCEL

VCR/DVD/TV

For Customer Use:

Enter below the Model No. and Serial No. which are located on the rear of cabinet.

Retain this information for future reference.

Model No.

Serial No.

LPT0674-001B

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause

hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet

basement, or near a swimming pool.

PORTABLE CART WARNING

(symbol provided by RETAC)

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table.

The unit may fall, causing serious injury, and serious damage to the unit.

An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation,

to ensure reliable operation of the unit, and to protect it from overheating.

S3125A

These openings must not be blocked or covered. The openings should never be blocked by placing the unit

on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat

source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided and/or the manufacturer’s instructions have been adhered to.

10. POWER SOURCES

This unit should be operated only from the type of power source indicated on the rating plate. If you are not

sure of the type of power supply to your home, consult your appliance dealer or local power company. For

units intended to operate from battery power, or other sources, refer to the operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert

the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug, if your unit is equipped

with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a ground-

ing-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet,

contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-

type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point

where they exit from the appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the

unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from touching such power lines or circuits, as

contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short

out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is

grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the

National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for

the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service personnel.

19. DAMAGE REQUIRING SERVICE

Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following

conditions:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions, as an improper adjustment of other controls

may result in damage and will often require extensive work by a qualified technician to restore the

unit to its normal operation.

e. If the unit has been dropped or the cabinet has been damaged.

f . When the unit exhibits a distinct change in performance, this indicates a need for service.

20. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by

the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

21. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to

determine that the unit is in proper operating condition.

22. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

23. DISC TRAY

Keep your fingers away from the disc tray as it is closing. It may cause serious personal injury.

24. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from

the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's

manual of the other equipment carefully and follow the instructions when making any connections.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS / Power Source

25. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the

laser beam. It may cause sight damage.

26. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious

personal injury and product malfunction.

27. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-

nected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

ANTENNA

DISCHARGE UNIT

GROUND CLAMP

(NEC SECTION 810-20)

ELECTRIC SERVICE

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

EQUIPMENT

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC-NATIONAL ELECTRICAL CODE

S2898A

CONDENSATION

Moisture will form in the operating section of the DVD/VCR if the player is brought from cool surroundings into a

warm room or if the temperature of the room rises suddenly. And when this happens, DVD/VCR's performance

will be impaired.

To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or

make sure that the room temperature rises gradually.

Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air

conditioner. In such cases, change the location of the DVD/VCR.

Power Source

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert

AC Outlet

the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Wider Hole

and Blade

NOTES:

Never connect the AC line cord plug to other than the specified

voltage (120V 60Hz). Use the attached power cord only.

If the polarized AC cord does not fit into a non-polarized AC

outlet, do not attempt to file or cut the blade. It is the user’s

responsibility to have an electrician replace the obsolete outlet.

If you cause a static discharge when touching the unit and the

unit fails to function, simply unplug the unit from the AC outlet

and plug it back in. The unit should return to normal operation.

•

Polarized AC Cord Plug

(One blade is wider than the other.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

DVD/CD Player/Video Cassette Recorder

• DVD/CD player with Video Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video

cassette recorder. The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higher

than Super VHS. Audio quality is higher than audio CD. The DVD PLAYER can play back video CDs and audio CDs.

• High Quality Picture - More than 500 lines(VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400

lines) or Laser Disc (430 lines) in resolution.

VCR Section

• Stereo/SAP Reception - This VCR is designed to receive stereo and separate audio program (SAP) broadcasts where

available.

• SQPB - Tapes recorded in the S-VHS system can be played back simply on this VCR.

• 4 Video Heads - Provides optimal picture quality for special effects playback.

• 19µm HEAD - For superior picture quality even in EP mode, 19micron width technology helps to avoid crosstalk and

boost EP picture quality to near SP levels. With precision technology, ghosts and color beats are virtually eliminated.

• Hi-Fi Stereo Sound - With a frequency response of 20 to 20,000 Hz and a dynamic range of better than 90dB, this

VCR provides a level of excellence that rivals compact discs.

• Instant Timer Recording (ITR) - Simply by pressing the REC and PLAY buttons, the VCR can be programmed for up

to 5 hours of recording with an immediate start.

• Skip Search - When the SKIP SEARCH button is pressed during playback, the VCR will automatically search forward

in 30 seconds increments to a maximum of 3 minutes with each press of the SKIP SEARCH button, and then return to

normal playback.

DVD Section

• Compatible with a wide range of DVD audio outputs

Digital Audio Jack (Optical or Coaxial):

• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect of

being in a movie theater or a concert hall.

• Surround standard different from Dolby Digital. This format is already in use in many theaters. By connecting this unit

to a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this format

can be enjoyed. However, audio will not be output from the analog audio output jacks.

• The MPEG audio of DVD discs recorded in this format can be enjoyed.

• The Linear PCM sound of a 48 kHz/16 bit through 96 kHz/20 bit exceeds audio CD sound.

• Surround audio - This DVD equipped with a “SPATIALIZER 3-D STEREO”. It can produce the effect of being in a cinema

or a concert hall.

• Multi-Language - Since this DVD matches with 124 language-subtitles/-soundtracks, you can enjoy selecting a favorite

one. (You can not select the language that is not recorded on the disc.)

• Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc, you

can change the angles during playback. (If a Multi-Angle is not recorded on the disc, you can not change the angle.)

• Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.

• Program/Random Playback (CD) - You can play back tracks in programmed or random-selected sequences.

• Zoom - You can zoom in on the selected subject on the screen during playback.

• Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor/television on a suitable disc.

• Parental Control - You can limit the playback of scenes or sounds of adult DVD discs which have a parental level rating.

* This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents

and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright

protection technology must be authorized by Macrovision Corporation or other rights owners and is intended for home

and other limited viewing uses only unless otherwise authorized by Macrovision Corporation or other rights owners.

Reverse engineering or disassembly is prohibited.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

* Certain audio features of this product manufactured under license from Desper Products,Inc. Spatializer and the circle

- in - square device are trademarks owned by Desper Products,Inc.

Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe the

rights of copyright owners and be contrary to copyright laws.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Before using your unit

Disc Playback operation

Important safeguards .......................................3

Power Source...................................................5

Features ...........................................................6

Contents...........................................................7

Parts and functions ..........................................8

Display .............................................................9

Remote control ...............................................10

Basic connections ..........................................12

CATV (CABLE TV) connections.....................14

Playback Connection .....................................16

Disc ................................................................ 35

Setting setup language .................................. 36

Playback procedure ....................................... 37

Special playback ............................................ 38

Zooming ......................................................... 39

Locating Desired Scene ................................. 39

Repeat playback ............................................ 40

Program playback (CD).................................. 41

Random playback (CD) .................................. 41

MP3 Playback ................................................ 42

Marking Desired Scenes ................................ 43

Changing soundtrack language ..................... 44

Subtitles ......................................................... 44

Changing angles ............................................ 45

Title selection ................................................. 45

DVD menu...................................................... 45

Setting up the VCR section

Setting the Video Channel ............................. 18

Setting the language ...................................... 18

Tuner Setting.................................................. 19

To ADD/DELETE channels............................. 20

Noise elimination ............................................ 20

Auto clock setting ........................................... 21

Manual clock setting....................................... 23

Loading and Unloading a Cassette Tape ....... 24

Advanced Function of DVD section

Parental control .............................................. 46

Temporary disabling of rating level by DVD

disc ................................................................. 47

Setting menu language .................................. 48

Setting subtitle language ................................ 49

Setting audio soundtrack language ................ 50

Setting surround sound .................................. 50

Setting the aspect ratio of TV screen ............. 51

Setting on Screen display .............................. 52

Status display of Disc ..................................... 52

Language Code List ....................................... 53

Tape Playback operation

Cassette tape Playback ................................. 25

Special playback ............................................ 26

ZERO RETURN function................................ 27

Video Index Search system ........................... 27

Recording

Recording a TV program ................................ 28

Instant Timer Recording (ITR)........................ 30

Timer Recording............................................. 31

Additional information

Problems and troubleshooting ....................... 54

Video head cleaning....................................... 55

Specifications ................................................. 56

HOW TO LOCATE YOUR JVC SERVICE

CENTER ........................................................ 58

LIMITED WARRANTY ................................... 59

Advanced Function of VCR section

Stereo Recording and Playback..................... 33

Separate Audio Program (SAP) ..................... 33

Duplicating a video tape................................. 34

Duplicating a disc material onto a video tape .... 34

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts and functions

Front

VCR/DVD mode selector button

Cassette Loading Slot

PLAY button

STOP button

OPEN/CLOSE button

Disc tray

EJECT button

PLAY STOP

POWER

EJECT

OPEN/CLOSE

REW FF

REC

DVD

VCR

VIDEO (M) L - AUDIO - R

VCR/DVD

Remote sensor

POWER

button

DVD indicator

CHANNEL +/– buttons

REW (Rewind) button

REC button

AUDIO (L/R)/

VIDEO IN jacks

VCR indicator

FF (Fast Forward) button

Rear

AC power cord

DVD OUTPUT

DIGITAL AUDIO

AUDIO

S-VIDEO

COMPONENT

OPTICAL

COAXIAL

VIDEO

(

)

ANT.

RF IN jack

B/CB

AUDIO

OUT

(

)

R/CR

DVD OPTICAL

DIGITAL AUDIO

OUT jack

RF OUT jack

CH.

3/4 Channel Selector Switch

DVD COAXIAL DIGITAL

AUDIO OUT jack

DVD/VCR common AUDIO (L/R)/VIDEO OUT

jacks

DVD AUDIO (L/R) OUT jacks

DVD S-VIDEO OUT jack

DVD COMPONENT OUT jacks

Download from Www.Somanuals.com. All Manuals Search And Download.

Display

Display window

No. Display

Description

VCR

VCR mode

Playback (lights) / Auto resume (flashes)

Still picture

DVD disc is inserted.

DVD

CD is inserted.

Display for afternoon (lights out in the morning)

Clock display (colon[ : ] flashes)

10 : 00

01 : 00

Counter display by hour/minute at VCR/DVD / by minute/second at CD

Track number display for CD

TV channel display for VCR

C002

C036

CATV channel display

External input display

Timer recording display

Video tape is in the unit

Track display for CD

TRK

Normal recording display (flashes during Instant Timer Recording - ITR)

11 REC

Explanation for On-Screen-Symbol:

Playback

Skip chapter to reverse

direction

Zoom

Stop

Parental level locked

Parental level unlocked

Screen size: Normal TV

Screen size: PAN SCAN

Screen size: WIDE

Shows Prohibited act

Output sound for Video-CD

Still picture

Open or Close the tray

Auto resume

Frame advanced playback

Forward slowmotion

Direction button’s mark

A-B repeat

A B

Fast Forward playback

Review playback

Skip chapter to forward

direction

Subtitle language

Soundtrack language

Angle

Note:

Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control

Page

18,36

TV/VCR/DVD switch Switch to operate TV or VCR or DVD

POWER

VCR

DVD

POWER

Power on/off

DVD MENU

MARKER

RETURN

OPEN/CLOSE

DISPLAY

A.TRK

Display menu of DVD software

Index for DVD

Remove DVD set up menu

Open or Close the tray

Change the front Display mode

Digital AUTO TRACKING

Set Subtitle of a DVD disc

Reset the counter to 00:00

Change playback angle of a DVD disc

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

SUB TITLE

C. RESET

ANGLE

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

ZERO RETURN

SEARCH MODE

SP/EP

Stop the tape when the counter reaches 00:00 27

POWER

Locating desired scene

28,30

40,41

Sets the tape speed for recording

Select playback mode

INPUT

PLAY MODE

ZOOM

Zoom (for DVD playback)

Select title of a DVD disc

TV VOL

TIMER

TV/VCR

TITLE

REPEAT A-B

0-9

Repeat playback between A and B (DVD/CD) 40

PLAY

Direct channel selection of TV

Input setting

20,28

39,41

46,47

31,32

18,29

STOP

Enter a password

SKIP

TIMER

TV/VCR

TV POWER

INPUT

TV VOL +/–

REW

Set the unit to start recording at a preset time

/INDEX

Switches between TV and VCR

ENTER/

SELECT

SET

Turn the connected TV on or off

Switch the connected TV to external mode

Adjust the connected TV’s volume

SET UP

CANCEL

Rewind/Review playback

Playback

25,26,38

25,37

PLAY

Fast Forward/Forward search playback 25,26,38

REC

Recording

Stop

28,30,34

25,37

VCR/DVD/TV

STOP

PAUSE

Still picture/Recording pause on/off 26,29,34,38

SKIP

Skip chapter to forward or reverse direction

Search for the INDEX mark of a tape

INDEX

JVC TV Remote Control

TV/VCR CH +/–

Select channel of the connected TV or VCR

This Remote can control some functions

(TV POWER, NUMBER(0-9), INPUT, TV

VOL +/–, TV CH +/– and ENTER) of a

remote controllable JVC TV by slide TV/

VCR/DVD switch to TV.

10,28,30,34

Cursor buttons

Setting buttons

SET –/+

31,32

Manual tracking buttons in playback mode

Cursor buttons - To move Up in the VCR menu

you press the . To move Down in the VCR

NOTE:

•

It’s not possible to operate a unit not

equipped with a remote sensor.

menu you press the

ENTER

Enter information in the menu

Select option in the menu

Display menu of setup

•

This Remote can control a JVC TV only.

When you operate the VCR or DVD, the

TV/VCR/DVD switch must be slided to

VCR/DVD again. Otherwise the DVD/

VCR may not operate properly.

Since this unit is combined type of DVD

and VCR, the remote code of DVD is

individual. So please note that the DVD-

keys on the RCU of the other JVC

RECEIVER/TV isnoteffectiveforthisunit.

SELECT

SET UP MENU

CANCEL

18,19,36,48-52

Delete Timer program

Cancel input data in the setting mode 23,31,39,41

OSD

Display VCR or DVD operation status

Switches sound between mono, stereo and SAP

Change sound track language of DVD

Slowmotion playback

29,52

•

A.MONITOR

SLOW

26,38

SKIP SEARCH

Skip the unwanted short material of a tape

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control

Inserting Batteries

Open the battery compart-

ment cover in the direction of

the arrow.

Install two "AA" batteries (supplied),

paying attention to the polarity

diagram in the battery compartment.

Replace the compartment

cover.

Battery precautions

The precautions below should be followed when using batteries in this device:

1.Use only the size and type of batteries specified.

2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.

Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from

possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery

manufacturer’s directions.)

Remote control basics

• Press POWER to turn the DVD/VCR on or off.

• Make sure TV/VCR/DVD switch is set to VCR/DVD.

• Tap VCR CH + or VCR CH – to move through the channels one channel at a time.

• The VCR CH +/– and SET +/– are also used to navigate on-screen menu system.

• You can directly access specific channels using Number keys pad.

• Each press of VCR or DVD, switches the screen between the VCR screen (VCR mode) and the DVD screen

(DVD mode).

Operation

• Aim the remote control at the remote sensor and press control buttons

to operate.

• Operate the remote control within 30° angle on either side of the remote

sensor, up to a distance of Approx. 5 meters.

Approx. 5 meters

Change the custom code for remote control

If you operate this DVD/VCR with another JVC’s VCR simultaneously arranging them side by side, the both

recorders will react to this remote control. In this case, you can change the remote control and DVD/VCR to other

frequency (“ ”). Then you can operate only this DVD/VCR with this changed remote control.

When you purchased, the DVD/VCR and remote control have been set to the frequency-“ ”.

Example: Change frequency to

DVD/VCR:

Remote control:

WhileholdingVCR,

press 2(code: b) of

Number keys. (in

case of code: A,

press 1)

MODE

SUB TITLE

ZOOM

ANGLE

TITLE

In the POWER off mode,

press and hold PLAY for

more than 5 seconds. “b”

will appear on the display

and then disappear after

approx. 4 seconds.

SP/EP

PLAY

REPEAT

A-B

POWER

MODE

VCR

DVD

POWER

INPUT

PLAY STOP

OPEN/CLOSE

REW FF

REC

DVD

TV VOL

TIMER

TV/VCR

OPEN/

DVD MENU

MARKER

RETURN

NOTE:

• If the remote control has been set to b, the DVD/VCR also must be set to b. Otherwise, the DVD/VCR can not be

operated with this remote control.

• To reset to “A”, repeat above procedure. However press 1 instead of 2.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic connections

If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber,skip

ahead to page 14 for the proper connections.

ANTENNA TO DVD/VCR CONNECTION

The DVD/VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TV

and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting

an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection

diagram.

Combination VHF/UHF Antenna with 75 ohm Coaxial Cable

DVD/VCR

(ANT.)

75 ohm Coaxial Cable

OUT

(TV)

Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire

DVD/VCR

Matching Transformer

300 ohm Input

(ANT.)

75 ohm output

(not supplied)

OUT

(TV)

300 ohm Twin Lead (Flat) Wire

DVD/VCR

Separate VHF and UHF Antennas

Combiner

75/300 ohm Inputs

75 ohm output

(not supplied)

UHF

VHF

(ANT.)

300 ohm Twin Lead (Flat) Wire

OUT

(TV)

75 ohm Coaxial Cable

NOTE: If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300

ohm inputs and one 75 ohm output.

NOTES: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the

antenna to the DVD/VCR properly.

• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of

an outdoor type antenna is required.

• If you are not sure about the connection, please refer to qualified service personnel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic connections

DVD/VCR TO TV CONNECTION

After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.

Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow

the connection diagram.

This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna

inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.

NOTE: If a VHF or UHF antenna is

used, set the TV/CATV

menu option to the "TV"

mode.

VHF/UHF IN

75 ohm Coaxial Cable (supplied)

TV with single 75 ohm VHF/UHF

antenna input

NOTE: If a VHF or UHF antenna is

Splitter

75 ohm Input

75/300 ohm outputs

(not supplied)

used, set the TV/CATV

menu option to the "TV"

mode.

UHF

VHF

75 ohm Coaxial Cable

(supplied)

TV with 300 ohm UHFand 75 ohm VHF

antenna inputs

NOTE: If a VHF or UHF antenna is

used, set the TV/CATV

menu option to the "TV"

mode.

UHF

Splitter

75 ohm Input

300 ohm outputs

(not supplied)

75 ohm Coaxial Cable

(supplied)

VHF

TV with 300 ohm UHF and 300 ohm VHF

antenna inputs

Download from Www.Somanuals.com. All Manuals Search And Download.

CATV (CABLE TV) connections

Many cable companies offer services permitting reception of extra channels including pay or subscription channels.

This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable

company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to

a special channel which is scrambled, you must have a descrambler box for proper reception.

DVD/VCR

(ANT.)

VHF/UHF

Incoming Cable

IN (ANT)

OUT

(TV)

ALLOWS: Recording of nonscrambled channels.

Use of the programmable timer.

Recording of one channel while watching another.

DVD/VCR

Converter/

Descrambler

(ANT.)

VHF/UHF

IN (ANT)

Incoming

Cable

OUT

(TV)

ALLOWS: Recording of channels through the converter box

(scrambled and unscrambled).

NOTE:

Using the programmable timer to record only the

channel selected at the converter box.

To record from converter/descrambler,

DVD/VCR tuner must be tuned to the

converter output channel, usually

channel 3 or 4.

PREVENTS: Recording one channel while watching another.

Using the DVD/VCR tuner to select channels.

DVD/VCR

(ANT.)

VHF/UHF

IN (ANT)

Converter/Descrambler

Incoming Cable

OUT

(TV)

NOTE:

ALLOWS: Recording of nonscrambled channels.

If you are playing a tape or using the

tuner built into the DVD/VCR, the

converter must be set to the video

channel output of the DVD/VCR (either

3 or 4).

Use of the programmable timer.

Recording an unscrambled channel while watching

any channel selected at the converter box.

PREVENTS: Recording scrambled channels.

NOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR

to the output of the Converter/Descrambler box, usually channel 3 or 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

CATV (CABLE TV) connections

IMPORTANT: Make sure the TV/CATV menu option is set to the "CATV" mode.

This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled

programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult

your local cable company for more information concerning connection to their descrambler equipment. There are many

ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.

DVD/VCR

Splitter

A/B Switch

VHF/UHF

IN (ANT)

(ANT.)

Incoming

Cable

OUT

(TV)

Converter/Descrambler

ALLOWS: Recording of one channel while watching another.

Using the programmable timer to record only the channel selected at the converter box.

Recording of all channels through the converter box.

PREVENTS: Watching scrambled channels while recording another channel.

Using the DVD/VCR tuner to select channels.

DVD/VCR

Splitter

(ANT.)

VHF/UHF

IN (ANT)

Converter/

Descrambler

A/B Switch

Incoming

Cable

OUT

(TV)

ALLOWS: Recording of nonscrambled channels.

Recording of one channel while watching another.

Watching premium channels through the converter while recording nonscrambled channels.

Using the programmable timer.

PREVENTS: Recording scrambled channels.

DVD/VCR

Converter/

Descrambler

Splitter

(ANT.)

VHF/UHF

IN (ANT)

Incoming

Cable

OUT

(TV)

Converter/

Descrambler

A/B Switch

ALLOWS: Recording of all channels through the converter box.

Recording a scrambled or unscrambled channel while watching another (scrambled or

unscrambled) channel.

Using the programmable timer to record only the channel selected at the converter box.

PREVENTS: Using the DVD/VCR tuner to select channels.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback Connection

The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent

on the model and features of each component. Check the Owner's Manual provided with each component for the

location of video and audio inputs and outputs.

Connect to a TV with Audio/Video Output

Use the supplied AUDIO/VIDEO Cord.

Audio (L) Output Video Output

DVD/VCR

DVD OUTPUT

DIGITAL AUDIO

AUDIO

S-VIDEO

COMPONENT

OPTICAL

COAXIAL

VIDEO

(

)

ANT.

PB/CB

AUDIO

OUT

(

)

PR/CR

CH.

To Video

Input

To Audio (R) Input

To Audio (L) Input

Audio (R) Output

AUDIO/VIDEO Cord (supplied)

Connect to a TV with S-Video Output

S-Video Cord (not supplied)

DVD/VCR

DVD OUTPUT

DIGITAL AUDIO

AUDIO

S-VIDEO

COMPONENT

OPTICAL

COAXIAL

VIDEO

(

)

ANT.

PB/CB

AUDIO

OUT

(

)

PR/CR

CH.

To S-Video Input

To Audio (R) Input

To Audio (L) Input

S-Video Output

Audio (L) Output

Audio (R) Output

AUDIO Cord (not supplied)

Connect to a BS TUNER

VHF/UHF

Antenna

Satellite

Antenna

75 ohm Coaxial Cable (not supplied)

To ANT. Input

DVD/VCR

ANT. Input

BS Tuner

DVD OUTPUT

DIGITAL AUDIO

AUDIO

S-VIDEO

COMPONENT

OPTICAL

COAXIAL

VIDEO

(

)

ANT.

B/CB

AUDIO

OUT

(

)

R/CR

CH.

ANT.

Output

Video Output

ANT. output

75 ohm Coaxial

Cable (supplied)

Audio (L) Output

To ANT.

Input

Audio (R) Output

AUDIO/VIDEO Cord (supplied)

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback Connection

Connect to a Stereo Amplifier with Audio Output

If your TV has a COMPONENT VIDEO IN jack, you can connect the DVD/VCR to the TV with a COMPONENT

cable (not supplied) as shown below. COMPONENT VIDEO output jack can send higher-quality video signal to a

TV than S-Video output.

COMPONENT VIDEO Cord (not supplied)

To Component

Video Output

Component

Video Input

AUDIO/VIDEO Cord (supplied)

To Audio/Video Input

To Audio/Video Output

DVD/VCR

Stereo Amplifier

DVD OUTPUT

DIGITAL AUDIO

AUDIO

S-VIDEO

COMPONENT

OPTICAL

COAXIAL

VIDEO

(

)

ANT.

PB/CB

AUDIO

OUT

(

)

PR/CR

CH.

Audio (L) Output

Audio (R) Output

To Audio (L) Input

To Audio (R) Input

AUDIO Cord (not supplied)

Connect to an AV Amplifier with built-in digital surround

If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems

such as Dolby Digital and DTS by using the Optical or Coaxial Digital Output.

Use this connection to connect an:

• AV amplifier with built-in *Dolby Digital decoder

• AV amplifier with built-in *DTS decoder

Video cord (not supplied)

To Video

DVD/VCR

Input

Video Output

DVD OUTPUT

DIGITAL AUDIO

AUDIO

S-VIDEO

COMPONENT

OPTICAL

COAXIAL

VIDEO

(

)

ANT.

B/CB

AUDIO

OUT

(

)

R/CR

CH.

NOTE:

AV Amplifier with

built-in various

decoder as above

You may connect to a TV with a

Component video cable(not supplied) or

S-Video cable(not supplied) instead of

a video cable(not supplied).

Coaxial digital

Audio Output

Coaxial digital cable

(not supplied)

Connecting the optical digital cable

You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital

cable.

When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.

When not using the optical digital cable, attach the dust protection cap to protect against dust.

NOTE:

•

The OPTICAL, COAXIAL, AUDIO L/R, S-VIDEO and COMPONENT jacks are useful only for DVD section. The

VHS signal is output only from the composite jack(DVD/VCR VIDEO OUTPUT) and UHF/VHF OUT.

When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on theAV

Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the

speakers to be damaged.

•

Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input

connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may

cause such a high level of noise that it may be harmful to your ears and damage your speakers.

DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is

necessary.

•

When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.

Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the Video Channel / Setting the language

When a TV is connected with the 75 ohm coaxial cable only.

Setting the Video Channel

To view playback of a recorded tape,

Press POWER to turn on the DVD/VCR.

or to watch a program selected by

the VCR's channel selector, the TV

must be set to channel 3 or 4 (video

channel).

Slide TV/VCR/DVD switch to VCR/DVD. Then press VCR to

2 _{select the VCR mode. The VCR indicator on the front panel}

will light.

Set the 3/4 Channel selector switch on the rear panel to CH

3 or 4.

POWER

VCR

DVD

Turn ON the TV and set to CH 3 or 4 to correspond with the

channel selected in step 3.

Press TV/VCR to select the VCR position.

5 _{The VCR indicator will appear in the display.}

Select any channel to receive a TV station in your area.

The channel number will appear on the screen for about

4 seconds.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

For a push-button TV tuner

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

If CH 3 or 4 corresponding to the video channel cannot be tuned

on your TV, proceed as follows: set the VCR 3/4 channel selector

and the TV to CH 3 or 4, play back a prerecorded tape and tune

the TV to receive a sharp color picture from the video cassette

recorder. Refer to your TV owner's manual for details.

POWER

INPUT

TV VOL

TIMER

TV/VCR

Setting the language

PLAY

You can choose from three different languages (English,

French and Spanish) for the on-screen displays.

STOP

Press SETUP MENU,

SKIP

If you use the unit for the first time

and press SETUP MENU, instead

of the main menu screen on the

right the SYSTEM SET UP menu

screen in step 2 may appear.

TIMER REC SET

AUTO REPEAT

SAP

SURROUND

CH SET UP

SYSTEM SET UP

/INDEX

ON OFF

ENTER/

SELECT

SET

SET UP

CANCEL

⟨+/-/ENTER/MENU⟩

Press

to select the

SYSTEM SET UP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

ON OFF

AUTO CLOCK

STANDARD TIME

“LANGUAGE” option, then press

ENTER.

NOTE:

•

ON OFF

If the unit does not operate properly,

or No key operation (by the unit

and/or the remote control): Static

electricity, etc., may affect the player's

operation. Disconnect the AC power

cord once, then connect it again.

If no buttons are pressed for more

than 60 seconds,the MENU screen

will return to normal TV operation

automatically.

DAYLIGHT SAVING TIME

⟨+/-/ENTER/MENU⟩

Press

toselectthedesired

language: English (ENGLISH),

Spanish (ESPAÑOL) or French

(FRANCAIS), then press ENTER.

•

Both the VCR and the DVD have their

own menu options (See page 36).

Press SETUP MENU until the MENU screen is cleared.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner Setting

This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to

the next channel set into memory, skipping over unwanted channels. Before selecting channels, they

must be programmed into the DVD/VCR’s memory. In addition to normal VHF and UHF channels, this DVD/

VCR can receive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CATV

menu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.

Preparation:

POWER

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

will light)

VCR

DVD

TV/CATV Selection

Press SETUP MENU. The VCR menu screen will appear.

Press

to select CH SET UP, then press ENTER.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

Press

CATV” option.

to select the “TV/

CH SET UP

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

TV CATV

AUTO CH MEMORY

ADD/DELETE

POWER

⟨+/-/ENTER/MENU⟩

INPUT

TV VOL

Then press ENTER to select the

TV or CATV mode. The arrow

indicates the selected mode.

CH SET UP

TV CATV

AUTO CH MEMORY

ADD/DELETE

TIMER

TV/VCR

PLAY

STOP

- VHF/UHF channels

⟨+/-/ENTER/MENU⟩

CATV - CABLE TV channels

SKIP

/INDEX

Press SETUP MENU until the menu screen is cleared.

ENTER/

SELECT

SET

SET UP

CANCEL

Setting channels automatically

The VCR can receive a maximum of 181 channels by

presetting the channels into memory.

Repeat above step 1 and press

CH SET UP

VCR/DVD/TV

to select AUTO CH

TV CATV

AUTO CH MEMORY

ADD/DELETE

MEMORY.

⟨+/-/ENTER/MENU⟩

NOTE:

You can not select "CH SET UP" if you

set the channel to "L".

Then press ENTER.

CH 002

The auto tuning will start. The

channel display will count up and

when finished, the screen returns

to normal.

Download from Www.Somanuals.com. All Manuals Search And Download.

To ADD/DELETE channels / Noise elimination

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

To ADD/DELETE channels

You can add the channels you want

or delete the channels you do not

want manually.

will light)

POWER

Repeat the step 1 on page 19.

VCR

DVD

CH SET UP

TV CATV

AUTO CH MEMORY

ADD/DELETE

Then press

to select the

“ADD/DELETE” option and press

ENTER.

⟨+/-/ENTER/MENU⟩

OPEN/

To Add or Delete desired channels

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

Press Number keys or

MODE

SUB TITLE

ADD

CH 003

to select a channel number

you want to add or delete.

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

To add channels

POWER

Press ENTER until “ADD”

appears on the screen to set

to add the unmemorized

channel.

⟨+/-/0-9/ENTER/MENU⟩

INPUT

TV VOL

TIMER

TV/VCR

To delete channels

Press ENTER until “DELETE” appears on the screen to

set to delete the channel from memory. The channel

number will blink.

PLAY

STOP

Repeat 1 to 2 to add or delete other channel.

SKIP

/INDEX

Press SETUP MENU until the menu screen is cleared.

ENTER/

SELECT

SET

SET UP

CANCEL

Noise elimination

When you don't want to receive a weak signal broadcast, the

Blue back screen can be obtained by selecting the NO NOISE

BACKGROUND "ON". When the unit is shipped from the

factory, the NO NOISE BACKGROUND is set to the "ON".

VCR/DVD/TV

Repeat the steps 1~2 on page 18 and press

NO NOISE BACKGROUND.

to select

Press ENTER to select the ON

SYSTEM SET UP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

ON OFF

2 _position.

AUTO CLOCK

ON OFF

STANDARD TIME

DAYLIGHT SAVING TIME

⟨+/-/ENTER/MENU⟩

Press SETUP MENU until the menu screen is cleared.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto clock setting

The Auto Clock feature enables the automatic clock setting and updating, and also to set the Time Zone

and Daylight Saving Time by receiving XDS (Extended Data Service) information carried on the channel

signal.

Preparation:

•

You must set the antenna connection before the AC cord plug is

inserted into the AC outlet.

Make sure the AUTO CH MEMORY(on P.19) is done.

•

Auto clock setting

POWER

VCR

DVD

WAIT 30 MINUTES! ^{when the power switch is off, after the}

connections of the antenna and the power plug. Because the Auto

Clock setting feature is activate.

After the clock is set automatically, you may have to set the Time

Zone and Daylight Saving Time.

Press POWER to turn on the DVD/VCR after the Auto Clock operation

completed.

•

When shipped from factory, the AUTO CLOCK option is set to ON position.

If you turn the DVD/VCR on during Auto Clock setting, the clock is not set.

With cable box connection, if the Auto Clock Setting is unsuccessful,

please select the PBS channel carrying the XDS information, then

turn the DVD/VCR off. After 30 minutes, turn the DVD/VCR on, and

if the clock is not set automatically, set the clock manually. (See page 23)

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Canadian Viewers:

POWER

Please see note regarding the Auto Clock Setting option on page 55.

INPUT

Time Zone setting (STANDARD TIME)

TV VOL

In the rare event that you live within broadcast range of two

stations in two different time zones, the DVD/VCR may recognize

the wrong station for the AUTO CLOCK set.

TIMER

TV/VCR

PLAY

To correct the situation:

Preparation:

• Turn ON the TV.

• When a TV is connected with an audio/video cable, select the video

input mode on the TV.

STOP

SKIP

/INDEX

• When a TV is connected only with an antenna cable, set to the

video channel 3 or 4. Then select VCR position with TV/VCR.

• Make sure the VCR mode has been selected. (Is the VCR indicator

being light?) (see steps 1~2 on page 18)

ENTER/

SELECT

SET

SET UP

CANCEL

Press SETUP MENU. The VCR menu screen will appear.

Press

to select the SYSTEM SET UP menu, then

press ENTER.

Press or

“STANDARD TIME” option, then

press ENTER.

to select the

SYSTEM SET UP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

ON OFF

VCR/DVD/TV

AUTO CLOCK

ON OFF

STANDARD TIME

DAYLIGHT SAVING TIME

⟨+/-/ENTER/MENU⟩

NOTE:

• AfterAuto Clock setting, in some case

the clock may display the other time

zone’s. You can correct the clock by

selecting your Time Zone setting

above.

• When the clock is not set or you set

the clock manually, Time Zone setting

is not available.

Press

to select your Time

STANDARD TIME

Zone, then press the ENTER.

ATLANTIC

CENTRAL

PACIFIC

HAWAII

EASTERN

MOUNTAIN

ALASKA

AUTO

⟨+/-/ENTER/MENU⟩

Press SETUP MENU until the MENU screen is cleared.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto clock setting

Daylight saving time setting

You can set the Daylight saving

time automatically or manually.

Preparation:

Turn ON the TV.

•

When a TV is connected with an audio/video cable, select the

video input mode on the TV.

When a TV is connected only with an antenna cable, set to the

video channel 3 or 4. Then select VCR position with TV/VCR.

Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

will light)

•

POWER

VCR

DVD

Repeat the step 1 on page 21 and

SYSTEM SET UP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

ON OFF

AUTO CLOCK

STANDARD TIME

DAYLIGHT SAVING TIME

press

to select DAYLIGHT

SAVINGTIME,thenpress ENTER.

ON OFF

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

⟨+/-/ENTER/MENU⟩

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Press

to select one of

DAYLIGHT SAVING TIME

POWER

the options, then press ENTER.

INPUT

OFF

AUTO

for manual setting

(forward one hour)

for manual setting

(back one hour)

for automatic setting

(read XDS in the signal)

ON:

⟨+/-/ENTER/MENU⟩

TV VOL

OFF:

AUTO:

TIMER

TV/VCR

PLAY

STOP

When you want to set the Daylight Saving Time manually, on

the first Sunday in April you set to “ON”, and on the last

Sunday in October you set to “OFF”.

SKIP

/INDEX

ENTER/

SELECT

SET

NOTES:

SET UP

CANCEL

When shipped from factory, the DAYLIGHT SAVING TIME

option is set to AUTO position.

•

• When the clock is not set, Daylight Saving Time setting is not

available.

•

When there is no Daylight Saving Time in your area, always

select OFF position in step 2.

VCR/DVD/TV

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual clock setting

You must set the date and time

manually for timer recordings and

Daylight Saving Time if the Auto

Clock process did not set them

correctly.

Preparation:

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

will light)

EXAMPLE: Setting the clock to "8:30 AM" March, 23 (SAT), 2002.

POWER

VCR

DVD

Press SETUP MENU. The VCR menu screen will appear.

Press

to select the

TIMER REC SET

AUTO REPEAT

SAP

SURROUND

CH SET UP

SYSTEM SET UP

SYSTEM SET UP menu, then

press ENTER.

ON OFF

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

⟨+/-/ENTER/MENU⟩

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Press

to select the

SYSTEM SET UP

CLOCK SET

LANGUAGE/IDIOMA/LANGUE

NO NOISE BACKGROUND

ON OFF

AUTO CLOCK

STANDARD TIME

POWER

“CLOCK SET” option, then press

ENTER.

INPUT

ON OFF

DAYLIGHT SAVING TIME

TV VOL

⟨+/-/ENTER/MENU⟩

TIMER

TV/VCR

PLAY

Press

to set the month,

MONTH

DAY

STOP

then press ENTER button.

1 (WED)

YEAR

TIME

2000

12 : 00AM

SKIP

/INDEX

⟨+/-/ENTER/CANCEL/MENU⟩

ENTER/

SELECT

SET

SET UP

To make corrections any time during the process

CANCEL

Press CANCEL repeatedly until the item you want to change

blinks, then press

Set the day, year and time as in

step 4.

MONTH

DAY

23 (SAT)

2002

VCR/DVD/TV

YEAR

TIME

8 : 30AM

⟨+/—/ENTER/CANCEL/MENU⟩

NOTE:

After a power failure or disconnection

of the power, the timer settings will be

lost. In this case, reset the present time.

After setting the clock, date and

time starts functioning

automatically.

8 : 30AM SAT

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading and Unloading a Cassette Tape

Use only video cassette tapes marked

and

•

Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording

is not possible with this model.

This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS

recordings with regular VHS resolution.

HQ VHS is compatible with existing VHS equipment.

Insert the cassette tape with its labeled side facing up

and the erase prevention tab positioned at your left. An

inverted cassette tape cannot be inserted.

Push the center of the tape until it is automatically

inserted.

VCR

Erase prevention tab

Automatic power ON

When you insert a cassette tape the VCR power will turn ON automatically.

Automatic playback

When loading a cassette tape without an erase prevention tab, playback will start automatically.

Unloading

Press EJECT on the unit.

Remove the cassette tape.

Automatic tape eject

This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its

beginning, the cassette tape will be ejected automatically.

To prevent accidental erasure

To record again

Removetheerasepreventiontabwithascrewdriver.

Cover the hole with a piece of adhesive tape.

Screwdriver

Erase prevention tab

Adhesive tape

Tape speed and maximum recording time

Video cassette tape

Tape Speed

T-160

2-2/3 hours

8 hours

T-120

2 hours

6 hours

T-90

T-60

T-30

SP (Standard Play)

EP (Extended Play)

1-1/2 hours

4-1/2 hours

1 hour

3 hours

30 minutes

1-1/2 hours

Download from Www.Somanuals.com. All Manuals Search And Download.

Cassette tape Playback

Preparation:

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

will light)

Load a prerecorded tape

POWER

VCR

DVD

(When loading a cassette tape

without the erase prevention

tab, playback will start auto-

matically).

To start playback

Press PLAY.

Playback will start.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

" will appear on the screen

MODE

SUB TITLE

for about 4 seconds.

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

POWER

To stop playback

INPUT

Press STOP once.

The tape will stop but remain

fully loaded and ready to play.

TV VOL

TIMER

TV/VCR

" will appear on the screen

for about 4 seconds.

PLAY

STOP

To rewind the tape or forward it rapidly

SKIP

/INDEX

Stop the playback or recording with STOP.

To rewind the tape:

To forward the tape:

Press FF.

ENTER/

SELECT

SET

Press REW.

SET UP

CANCEL

VCR/DVD/TV

To stop the tape-winding, press STOP. To switch to playback

directly (without STOP), press PLAY.

Forward/Reverse picture search mode

NOTE:

When the tape is being winded, you can switch to picture search

mode (see next page). To do this, press REW or FF and hold it

down.Theunitwillresumethetapewindingassoonasthebutton

is released.

•

This VCR selects the playback tape

speed SP or EP automatically.

•

The Cassette tape and DVD disc can

be played back simultaneously. If you

press VCR or DVD, the tape playback

and DVD playback alternate with each

other on the screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Special playback

Picture Search

Repeat playback

The entire video tape will be played until its end.The

tape will then automatically rewind to the beginning and

the playback will be repeated.

Reverse picture search function

Press REW x 1 or x 2 during the playback.

Forward picture search function

Press SETUP MENU. Press

AUTO REPEAT.

to select

Press FF x 1 or x 2 during the playback.

To return to playback: Press PLAY.

Then press ENTER to

TIMER REC SET

AUTO REPEAT

SAP

SURROUND

CH SET UP

select [ON] or [OFF].

If [ON] is selected, the

playback will be

repeated endlessly.

ON OFF

Still Picture

Press PAUSE during playback. To resume normal

playback: Press PLAY.

SYSTEM SET UP

⟨+/-/ENTER/MENU⟩

Slow Motion

Press SETUP MENU until the menu screen is

cleared.

if you press OSD, " " will appear on the screen.

During playback press SLOW.

To return to playback: Press PLAY or SLOW.

Slow tracking and vertical lock adjustment

If noise bars appear in the picture during slow motion,

press the SET + or – to reduce the noise bars.

If the still picture jitters excessively, press SET + or –

to stabilize the still picture.

To start the playback, press PLAY.

The playback will be repeated endlessly.

To cancel repeat mode:

Follow the above step 1, then press ENTER to select

the OFF position. Press SETUP MENU to return to

the TV.

Frame by Frame picture

Press PAUSE during playback.

Press SLOW one by one: The picture advances frame

by frame.

To return to playback: Press PLAY or PAUSE.

Skip Search

Adjusting tracking condition

Each time you press SKIP SEARCH while a tape is

playing, the unit will fast-forward ahead 30 seconds

on the tape. You may press the button up to six times

in a row to move 180 seconds (three minutes) ahead.

Automatic tracking adjustment

Whenever you insert a tape and start playback,

automatic tracking starts working and continuously

analyzes the signal to enable optimum picture quality

during playback.

1 press: 30 seconds of tape

2 presses: 60 seconds of tape

3 presses: 90 seconds of tape

For example:

Manual tracking adjustment

If automatic tracking cannot eliminate noises well during

playback, press SET +/– to eliminate the noises.

“MANUAL TR.” will appear. Press it briefly for a fine

adjustment, or press and hold for a coarse adjustment.

•

Press A.TRK to reactivate automatic tracking again.

“AUTO TR.” will appear.

Note:

The audio output is muted during SPEED SEARCH,

STILL, FRAME ADVANCE and SLOW MOTION.

•

• During picture search mode there will be noise bars

which are caused by the system.

• The Special Playback will automatically change to

playback after approx. 5 minutes to protect the video

tape against excessive wear.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZERO RETURN function / Video Index Search system

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

ZERO RETURN function

This function makes tape-rewinding

stop at the counter 00:00:00 position

automatically.

will light)

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Press OSD.

The counter display shows the tape

running time during playback or

8 : 47AM MON

STEREO SAP

CH 001

ZERO RETURN

MODE

SUB TITLE

SP/EP

recording.

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

VCR

00 : 04 : 38 SP

POWER

Press C. RESET at the desired tape po-

sition. The counter display will be reset

to the "00:00:00" position (e.g. the

INPUT

8 : 47AM MON

STEREO SAP

CH 001

begining of recording).

TV VOL

VCR

00 : 00 : 00 SP

TIMER

TV/VCR

PLAY

Press STOP when playback or recording is finished.

Press ZERO RETURN.

The tape will be rewinded or fast forwarded and automatically

STOP

stop at the ”00:00:00” position.

SKIP

/INDEX

The DISPLAY-button

Press DISPLAY. The clock and tape counter

ENTER/

SELECT

SET

VCR

SET UP

alternate with each other in the display.

CANCEL

VCR

NOTE for Counter Display:

Video Index Search system

This function enables you to locate the beginning of any

recording made on the VCR.

•

Ifyourewindthetapebeyond“00:00:00”,

a minus sign (“–”) will be displayed in

front of the time counter.

•

When you load a tape, the counter will

reset to “00:00:00”.

The counter does not function on

nonrecorded (blank) sections of the

tape.Whenyourewind,fastforwardor

play tapes through blank sections, the

counter stops.

Recording an INDEX MARK

The Index Search function automatically

records an INDEX mark on the tape

whenever a recording is initiated.

CH 001

INDEX

NOTE for Video Index Search system:

Index Search

Press INDEX

mode.

For Succeeding programs: Press INDEX

For Preceding programs: Press INDEX

(Additional press increases the INDEX NO.

up to 9.)

•

When you record an INDEX mark at

the very beginning of the tape, the

mark may not be found.

During INDEX search, the tape may

stop and begin to play at a slightly

different location.

during stop or play

•

INDEX may not function properly with

old or worn out video tapes.

INDEX marks may not be found if it is

extremely close to the point where the

search began.

In recording, if you stop recording

temporarily, the INDEX mark is not

recorded on the tape.

When the INDEX

is pressed, the

is displayed

unit starts searching the INDEX NO.

selected and finds the portion, then

playback starts automatically.

INDEX NO. (up to 9)

•

To stop the Index Search, press STOP.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording a TV program

Recording and viewing the

same TV program

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

will light)

Load a cassette tape with the erase

prevention tab intact.

The VCR will automatically turn on.

POWER

VCR

DVD

Press SP/EP to select the desired tape

2 _{speed SP or EP.}

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

The tape counter and SP or EP will

appear on the screen for about 4

ZERO RETURN

MODE

SUB TITLE

00 : 00 : 00 SP

SP/EP

seconds.

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

POWER

Set the TV/CATV option to the appropriate position (See page

19).

INPUT

- VHF/UHF channels

CATV - CABLE TV channels

TV VOL

TIMER

TV/VCR

Press Number keys or VCR CH +/– to select the channel to

4 _{be recorded.}

PLAY

1-9

Press 0 twice and then 1-9 as required. Example: To

select 2, Press “002”.

Press 0 first and then the remaining 2 digits in order

from left to right.

STOP

10-12

SKIP

/INDEX

Example: Press 012 for “12”.

Press 2 digits in order.

CH 110

13-99

ENTER/

SELECT

Example: Press 22 for “22”.

SET

100-125 Press the 3 digits in order.

SET UP

CANCEL

Example: Press 110 for “110”.

VHF/UHF/CATV CHANNELS

CATV

VHF

2-13

VHF

2-13

UHF

14-69

STD/HRC/IRC

14-36 (A) (W)

VCR/DVD/TV

37-59 (AA) (WW)

60-85 (AAA) (ZZZ)

86-94 (86) (94)

95-99 (A-5) (A-1)

100-125 (100)(125)

01 (5A)

NOTE:

• Iftheerasepreventiontabisremoved,

the tape will eject when both the REC

and PLAY are pressed for recording.

• If you wish to watch the DVD playback

during the normal recording on VCR,

press DVD to change to DVD mode

and perform the DVD playback(see

P.37).

On the VCR, press REC.

5 _{Or on the Remote, while holding REC,}

CH 110

press PLAY.

" will appear on the screen for

INDEX

about 4 seconds and “REC” will

appear on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording a TV program

To stop recording

Press STOP to stop recording.

" will appear on screen for about 4

seconds.

To stop recording temporarily

POWER

VCR

DVD

Press PAUSE to avoid recording unwanted

material. Press again to continue the

recording.

" will appear on screen for about 4

seconds.

NOTE:

OPEN/

•

The pause function will be released after 5 minutes to prevent damage

to the tape or the VCR. The VCR will change to the STOP mode.

You can select a recording channel in the recording pause mode.

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

•

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Recording one program while watching another

POWER

While the VCR is recording, press TV/VCR to select the TV position.

The “VCR” will go off and recording will continue.

INPUT

Select the TV channel you want to watch by using the TV channel

selector. If the connected TV is JVC’s, use TV CH +/– after slide TV/

VCR/DVD switch to TV.

TV VOL

TIMER

TV/VCR

NOTE:

PLAY

Some CATV hookups do not permit viewing one channel while

recording another. See pages 14,15.

STOP

SKIP

To Display VCR operation Status

/INDEX

Press OSD. The clock, day of the week and more information will be

indicated.

ENTER/

SELECT

SET

While watching TV

DAY OF THE WEEK

SET UP

CANCEL

CLOCK

8 : 47AM MON

STEREO SAP

CH 125

CHANNEL

STEREO AND

SEPARATE AUDIO

PROGRAM (SAP)

00 : 00 : 00 SP

TAPE SPEED

VCR/DVD/TV

REAL TIME COUNTER

While operating a tape

Auto Rewind feature

This VCR will automatically rewind the

tape when the tape has ended (except

during ITR and TIMER REC). It will also

eject the tape.

OPERATING

MODE

8 : 30AM MON

HI-FI

CH 125

HI-FI STEREO

AUTO REPEAT

TAPE IN

00 : 00 : 00 SP

To cancel the display: Press OSD until all indicators disappear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Instant Timer Recording (ITR)

The Instant Timer Recording

feature provides a simple and

convenient way to make a timed

recording.

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode. (The VCR indicator

will light)

Example: Instant Timer Recording for 30 minutes.

POWER

VCR

DVD

Load a cassette tape with the erase

prevention tab intact.

The VCR will automatically turn on.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Press SP/EP to select the desired tape

ZERO RETURN

2 _{speed SP or EP.}

MODE

SUB TITLE

The tape counter and SP or EP will

appear on the screen for about 4

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

00 : 00 : 00 SP

seconds.

POWER

INPUT

Set the TV/CATV option to the appropriate position (See page

19).

- VHF/UHF channels

TV VOL

CATV - CABLE TV channels

TIMER

TV/VCR

PLAY

Press Number keys or VCR CH +/– to

4 _{select the channel to be recorded.}

CH 110

STOP

SKIP

/INDEX

ENTER/

SELECT

SET

Press REC on the VCR or while holding REC, press PLAY on

the Remote to begin recording. Press REC on the VCR again to

stop recording after 30 minutes. Each additional press of REC

will increase recording time as shown in the chart below, up to a

maximum of 5 hours. The ITR and recording time will appear on

the screen for about 4 seconds. And, REC will keep blinking in

the display.

SET UP

CANCEL

Press Recording time Press

Recording time

ITR 0 : 30

CH 125

VCR/DVD/TV

NORMAL REC 6 times

3:00

once

4:00

twice

0:30

1:00

1:30

2:00

7 times

8 times

9 times

5:00

3 times

4 times

5 times

INDEX

NORMAL REC

NOTE:

If you wish to watch the DVD playback

during the ITR, press DVD to change to

DVD mode and perform the DVD

playback(see P.37).

To cancel ITR

Press STOP or turn off the power.

" will appear on screen for about 4

seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

Timer Recording

Timer recording can be programmed

on-screen with the remote control.

The built-in timer allows automatic

unattended recording of up to 8

programs within 1 month.

Preparation:

Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press VCR to select the VCR mode.

•

• Load a cassette tape with the erase prevention tab intact.

• Press OSD to verify that the time and date are correct.(see page

29).

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Example: Program a timer recording for the 26th day, channel 125

(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP).

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

Press SETUP MENU. Select the

TIMER REC SET option, then press

ENTER.

TIMER REC SET

AUTO REPEAT

SAP

SURROUND

CH SET UP

SYSTEM SET UP

ZOOM

TITLE

MODE

ON OFF

POWER

INPUT

⟨+/-/ENTER/MENU⟩

Press SET + or – to select one of the

DATE

START END

TV VOL

2 _{program line, then press ENTER.}

— — — — — —— : — — — : — — — —

—

TIMER

TV/VCR

—

PLAY

—

⟨+/-/ENTER/CANCEL/MENU⟩

STOP

Press SET + or – to select the date,

then press ENTER.

DATE

START END

26(SU)

— : — — — : — — — —

—

SKIP

— — — — — —— : — — — : — — — —

—

/INDEX

— — — — — —— : — — — : — — — —

—

ENTER/

SELECT

SET

—

⟨+/-/ENTER/CANCEL/MENU⟩

SET UP

CANCEL

Set the start time, end time, channel

DATE

START END

4 _{and tape speed as in step 3.}

2_—6_—(S_—U_—) _—1_——1:0_{: —}0P_—M 1_—1:3_{: —}0P_—M125 EP

— —

—

— — — — — —— : — — — : — — — —

—

— — — — — —— : — — — : — — — —

—

NOTE:

—

NOTE:

—

• PressCANCELtomovecursorbackward

for correction.

• To record from external source set the

channel to "L". "L" will appear next to CH

125 (or 69).

—

• Iftheclocksymbol( )blinkswhenthe

timerrecordingended,theTVprogram

has not been completely recorded

becauseofaninsufficienttapesupply.

In this case, press TIMER to cancel

the timer program or press EJECT to

remove the cassette tape.

• During timer recording standby mode,

the VCR mode cannot be selected. To

use the VCR, press TIMER at first,

then press VCR to change to VCR

mode. After you use the VCR, press

TIMER again to put the VCR into timer

recording standby mode.

• If you press TIMER during timer

recording, the recording operation will

be interrupted. If you press TIMER

againwithintheprogrammedtime,the

recording operation will start again.

• After a power failure or disconnection

of the power plug, all programmed

recording settings and time display

will be lost upon resumption of power.

Inthiscase,resettheclock(seepages

21-23) and reprogram any timer

recordings.

⟨+/-/ENTER/CANCEL/MENU⟩

To enter other programs, repeat step

2 through 4.

DATE

START END

2_—6_—(S_—U_—) _—1_——1:0_{: —}0P_—M 1_—1:3_{: —}0P_—M125 EP

— —

—

— — — — — —— : — — — : — — — —

—

— — — — — —— : — — — : — — — —

—

• To return to the normal screen,

press SETUP MENU twice.

—

⟨+/-/ENTER/CANCEL/MENU⟩

Press TIMER. The clock symbol( ) will appear on the display

and the VCR stands by for recording. At the same time, VCR

mode will change to DVD mode automatically. You can use

DVD even if the VCR is in the Timer recording mode.

If you do not use the DVD, turn the power off.

The timer recording will start at 5 seconds before the time you

predetermined.

NOTE:

•

If the clock symbol( ) does not appear on the display in spite

of the pressing of TIMER, the cassette may not have been

loaded yet.(see page 24)

•

If the cassette is ejected in spite of the pressing of TIMER , the

erase prevention tab of the cassette may have been

removed.(see page 24)

Download from Www.Somanuals.com. All Manuals Search And Download.

Timer-Recording

Timer Recording Special case

Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g.

MO-SA: Monday to Saturday) Timer recording

Confirmation / Cancellation of the Timer

Recording

If the Timer has been activated, press TIMER to

Follow the procedure of timer recording on the previous

page. At picture 3 press SET + or – repeatedly until the

desired setting appears. Then press ENTER.

deactivate the Timer. The clock symbol( ) will

disappear. Then press VCR to change to VCR

mode.

When you press SET – repeatedly, the indicator at

DATE will change as follows, in this case the today is

Friday.

To confirm Timer program:

At picture 1 on the

DATE

START END

2_—6_—(S_—U_—) _—1_——1:0_{: —}0P_—M 1_—1:3_{: —}0P_—M125 EP

previous page select the

TIMER REC SET option

and press ENTER.

— —

—

— — — — — —— : — — — : — — — —

—

The current day (Friday)

SU-SA (Sunday to Saturday)

— — — — — —— : — — — : — — — —

—

MO-SA (Monday to Saturday)

MO-FR (Monday to Friday)

WKL-TH (Weekly Thursday)

Then the timer program

list as right will appear on

the screen.

—

One month later

minus one day

⟨+/-/ENTER/CANCEL/MENU⟩

WKL-WE

(Weekly Wednesday)

To cancel Timer program:

Press SET + or – to

select the unnecessary

program, then press

CANCEL to cancel the

program.

DATE

— — — — — —— : — — — : — — — —

START END

—

DATE

START END

— : — — — : — — — —

— — — — — —— : — — — : — — — —

—

WKL-WE

—

⟨+/-/ENTER/CANCEL/MENU⟩

—

⟨+/-/ENTER/CANCEL/MENU⟩

PressSETUPMENUrepeatedlyuntiltheTV-picture

appears.

In case Timer programs-overlap

•

Do not overlap timer programs as portions of the

conflicting programs will be lost. The first recording

timehaspriorityoverthenextrecordingtimeasshown

in the diagram below.

NOTE:

•

If there are other timer record programs remaining,

TIMER must be pressed to reactivate the timer,

otherwise the remaining timer record programs will

be ignored.

•

You cannot confirm the Timer program during timer

recording operation.

You can also correct the programmed setting in

program confirm mode.

8 : 00

9 : 00

10 : 00

11 : 00

Program 1

Program 2

Deleted Parts

Program 3

At step 2 above, press ENTER to enter the program

input mode. Then press ENTER repeatedly until the

item you wish to correct

Non Recorded Portion Parts

Recording

Control Settings

Prog.1

Prog.2

Prog.3

DATE

START END

2_—6_—(S_—U_—) _—1_——1:0_{: —}0P_—M 1_—1:3_{: —}0P_—M125 EP

blinks. Thencorrectthedata

with SET + or –.

Then press SETUP MENU

repeatedly until the TV-

picture appears.

— —

—

— — — — — —— : — — — : — — — —

—

— — — — — —— : — — — : — — — —

—

⟨+/-/ENTER/CANCEL/MENU⟩

NOTE:

•

The daily/weekly recording can be made continu-

ously until the recording is canceled or the tape

reaches the end.

•

During timer recording the automatic rewinding

mechanism does not function.

Download from Www.Somanuals.com. All Manuals Search And Download.

Stereo Recording and Playback / Separate Audio Program (SAP)

Stereo Recording and

When a MTS STEREO broadcast is

received, the word STEREO will appear

on the screen and the program can be

viewed or recorded in stereo.

The Hi-Fi STEREO recording procedure

is the same as for normal recordings.

Playback

The VHS Hi-Fi audio system permits high

fidelity recording of MTS STEREO TV

broadcasts.

STEREO

POWER

NOTE:

VCR

DVD

WhenusingaCATVsystem, stereoTVprogramsmaybetransmitted

over a mono cable channel. In this case the word "STEREO" will not

appear and the sound will be in mono.

Output selection

When viewing an MTS STEREO TV program, or playing a prerecorded

VHS Hi-Fi STEREO videotape, press A. MONITOR to select how the

audio will be heard through the speakers. Normally set to the Hi-Fi

STEREO position, this button can be set to the MONO position if the

stereo broadcast or videotape audio is of poor quality. The "R" and "L"

positions allow the audio from the Right or Left Hi-Fi channel to be heard

over both TV speakers. This button has no effect when viewing a MONO

videotape or TV program. Each time when you press the button, OUTPUT

SELECTION display appears on the screen for several seconds. Refer

to the chart below.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

POWER

OUTPUT

SOUND HEARD ON BOTH

INPUT

SELECTION SPEAKERS

STEREO

L ch

R ch

STEREO

TV VOL

LEFT CHANNEL AUDIO

RIGHT CHANNEL AUDIO

MONO

TIMER

TV/VCR

MONO

PLAY

STOP

Separate Audio Program (SAP)

SKIP

/INDEX

Your VCR is fitted with a SAP broadcast system which enables

you to switch to a separate audio program when viewing a

selected channel.

ENTER/

SELECT

SET

This function applies only when the program is broadcast in

multi-languages through the SAP broadcast system.

SET UP

CANCEL

Press SETUP MENU. Then press

Then press ENTER to select [ON].

to select SAP.

TIMER REC SET

AUTO REPEAT

SAP

SURROUND

CH SET UP

ON OFF

Then press SETUP MENU until

the menu screen is cleared.

VCR/DVD/TV

SYSTEM SET UP

⟨+/-/ENTER/MENU⟩

NOTE:

Listening to SAP

• When playing back a tape that is not

recorded in Hi-Fi stereo mode, the

audio will automatically be monaural.

• When listening to a VHS Hi-Fi video

tape or MTS broadcast through the

VHF/UHF jack (Audio/Video cord not

connected), the sound will be

monaural.

When the VCR is turned on or a channel selection is made, make

certain the letters "SAP" appears on the screen. This means that the

"Separate Audio Program" broadcasting is available.

STEREO SAP

SAP

Download from Www.Somanuals.com. All Manuals Search And Download.

Duplicating a video tape/Duplicating a disc material onto a video tape

Duplicating a video tape

If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.

Make all connections before turning on the power.

Load a blank cassette tape with the erase preven-

tion tab intact into the recording VCR.

Load a previously recorded tape into the playback

VCR or CAMCORDER.

Press REC on the recording VCR.

Or on the Remote, while holding REC, press PLAY.

Then press PAUSE.

Press PLAY button on the playback VCR or

CAMCORDER, then press PAUSE button.

Press SP/EP to select the desired tape speed SP

or EP.

It is recommended that you set the speed to the

SP mode on the recording VCR for best results.

Press PAUSE on both the VCRs simultaneously to

begin the duplicating process.

Press VCR CH + or – to selectAUDIO/VIDEO input

position. "L" will appear in the

display.

Connection with Video camera

Connection with second Video recorder

Playback VCR

Playback Camcorder

To AV Jack

To VIDEO OUT

To AUDIO (R) OUT

To AUDIO (L) OUT

Recording VCR

AUDIO/VIDEO Cord (supplied)

Recording VCR

To AUDIO (R) IN

To AUDIO (L) IN

AUDIO/VIDEO Cord (not supplied)

To VIDEO IN

To AUDIO (R) IN

To AUDIO (L) IN

To VIDEO IN

For duplicating a previously recorded tape from a

camcorder, follow the camcorder manufacturer’s

instructions. A typical camcorder dubbing hookup

is shown above.

Duplicating a disc material onto a video tape

You can record disc material in DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR only.

If the DVD disc has a Copy-guard feature, the duplicating is not possible. A symbol mark “ ” will

appear on the screen for approx. 4 seconds. See page 37 for more information about the DVD playback.

Preparation:

• Load a cassette tape with the erase prevention tab

intact.

During disc playback, press REC on the VCR or

while holding REC, press PLAY on the Remote.

The duplicating will start.

•

Select the tape speed in the VCR mode. (see P.28)

Load a disc you wish to duplicate.

Note:

Press DVD to select the DVD mode. (The DVD

indicator will light)

You can set the duplicating time using the ITR-function.

At step 3 above press REC repeatedly until the desired

duplicating time appears on the screen.(P.30)

Press PLAY to start the disc playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc

This unit applies to DVD discs from Region 1 only.

The loaded Disc (DVD, Video-CD, Audio-CD and MP3-CD) will be recognized automatically.

The suitable Disc-formats are: DVD, CD-R and CD-RW.

Do not play DVD-ROM, DVD-Audio, CDV, CD-G or Photo CD to prevent accidental erasure of prerecorded material.

Some DVDs are played back with a Copy guard system. In case of a dubbing on video tape, strong disturbance may

occur. This is not a defect of this DVD/VCR.

Title

When two or more movies are recorded on a disc,

DVD DISC

the disc is divided into two or more sections. Each

section is called a “TITLE”.

TITLE1

CHAPTER 1

TITLE2

CHAPTER 2

CHAPTER 1

CHAPTER 2

CHAPTER 3

Chapter

The titles can be subdivided into many sections.

Each section is called a “CHAPTER”.

Video-CD/Audio-CD

Video-CD/Audio-CD-Track

An Video CD or Audio CD can contain several items.

These are assigned to the tracks.

TRACK

Removing Disc from Case

Be sure to hold the edge of disc. Do not touch the surface of the disc.

Pick up the disc gently from the case.

• Do not scratch the disc.

• Do not get dirt on the surface of the disc.

• Do not stick a label or adhesive tape on the disc.

• Do not drop or bend the disc.

Storing Disc

• Store the disc in the case to avoid risk of scratches, dirt or damage.

• Do not leave disc exposed to direct sunlight or in hot or humid places.

Cleaning Disc

Wipe the disc with a clean, dry cloth from center to edge.

• Do not wipe the disc round.

• Do not use liquid or aerosol cleaners.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting setup language

The setup language can be selected.

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

• When using an amplifier, switch on the amplifier.

POWER

VCR

DVD

Press DVD to select the DVD

No Disc

mode. (The DVD indicator will

light)

“No Disc” will appear on the

screen.(IfaDVDdischasalready

loaded, the playback will start

automatically.)

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Press SETUP MENU in the stop

mode. The SETUP MENU of

DVD will appear on the screen.

Language Picture

Parental

Other

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Then press

to select

Other.

POWER

/Enter/Setup/Return

INPUT

Language Picture

Parental

Press ENTER to select OSD

Language.

TV VOL

TIMER

TV/VCR

OSD Language English

PLAY

STOP

/Enter/Setup/Return

SKIP

/INDEX

Language Picture

Parental

Press

and then press

to select desired language

(e.g. English), then press

ENTER.

ENTER/

SELECT

SET

OSD Language English

English

Francais

Espanol

SET UP

CANCEL

/Enter/Setup/Return

VCR/DVD/TV

NOTE: To make the SETUP screen disappear, press SETUP

MENU (or RETURN).

If the DVD/VCR does not operate

properly: Static electricity, etc., may

affect the player's operation. Disconnect

the AC power cord once, then connect

it again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback procedure

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

POWER

VCR

DVD

Press OPEN/CLOSE.

The disc tray will open.

Place a disc onto the tray.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Hold the disc, position it with the

ZERO RETURN

printed label side up, align it with

the guides, and place it in its

proper position.

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Press PLAY or OPEN/CLOSE.

POWER

The disc tray closes automati-

cally.

INPUT

On the screen,

changes to

“Reading” and then playback will

commence.

TV VOL

TIMER

TV/VCR

• A menu screen may appear on

the TV screen, if the disc has

a menu feature. In this case,

PLAY

Reading

STOP

press

ENTER to operate a menu

feature.

SKIP

/INDEX

Press STOP to end playback.

• The DVD/VCR memorizes the stopped point, depending on

the disc. “ ” appears on the screen for approx. 4 seconds.

ENTER/

SELECT

SET

SET UP

CANCEL

“

” keep blinking in the display until the playback is stopped

completely. Press PLAY to resume playback (from the scene

point).

• If you press STOP again(“ ” appears on the screen) or unload

the disc, the DVD/VCR will clear the stopped point.

Then press OPEN/CLOSE.

The disc tray opens.

Remove the disc and press POWER.

The disc tray closes automatically and DVD/VCR turns off.

VCR/DVD/TV

Note:

•

If a non-compatible disc is loaded, "Incorrect Disc", "Region Code Error" or "Parental Error" will appear on the TV

screen according to the type of loaded disc. In this case, check your disc again (See pages 35 and 46).

Some discs may take a minute or so to start playback.

A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you

tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate

a problem with the DVD/VCR.

•

When you set a single-faced disc label downwards (ie. the wrong way up) and press PLAY or OPEN/CLOSE,

"Reading" will appear and remain on the screen for approx. 40 seconds and then it will change to "No Disc".

Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays

DVDs according to the disc contents the software producers designed, some playback features may not be

available. Also refer to the instructions supplied with the DVDs.

•

When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid

possible damage to the audio system, the consumer should take proper precautions when the analog stereo

outputs of the DVD/VCR are connected to an amplification system.

Download from Www.Somanuals.com. All Manuals Search And Download.

Special playback

Note: There may be a slight delay be-

tween pressing the button and the

function activation.

Fast Forward Playback

Press FF during normal playback.

EachpressofFF willincreasethespeedofthesearchx2, x4, x8, x20.

(in case of Audio-CD: x6 and x16 are available)

• To resume normal playback, press PLAY.

POWER

VCR

DVD

Review Playback

Press REW during normal playback.

Each press of REW will increase the speed of the search x2, x4, x8,

x20. (in case of Audio-CD: x6 and x16 are available)

• To resume normal playback, press PLAY.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

Still Playback

MODE

SUB TITLE

SP/EP

Press PAUSE during normal

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

playback.

POWER

To resume normal playback, press

PLAY.

INPUT

TV VOL

TIMER

TV/VCR

PLAY

Frame Advance

Press PAUSE during still playback.

One frame is advanced each time

you press PAUSE.

STOP

SKIP

/INDEX

To resume normal playback, press

PLAY.

ENTER/

SELECT

SET

SET UP

CANCEL

Slow-motion Playback

Press SLOW during normal playback or still playback.

Each press of SLOW will change the speed of the slow x1/2, x1/4,

x1/6, x1/7.

VCR/DVD/TV

• To resume normal playback, press PLAY.

• To resume the still playback, press PAUSE.

Note:

The unit is capable of holding a still video

image or On screen display image on your

television screen indefinitely. If you leave

the still video image or On screen display

image displayed on your TV for an ex-

tended period of time, you risk permanent

damage to your television screen.

Projection televisions are very susceptible.

Locating a chapter or track

Press SKIP (

) Forward or SKIP (

) Reverse during play-

back to locate a chapter that you want to watch.

Each time you press the button, a chapter or track is skipped.

Download from Www.Somanuals.com. All Manuals Search And Download.

Zooming / Locating Desired Scene

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Zooming

POWER

VCR

DVD

This unit will allow you to zoom in on the frame image. You can

then make selections by switching the position of the frame.

Press ZOOM during playback.

The center part of the image will

be zoomed in.

EachpressofZOOMwillchange

the ZOOM

(x 1.3),

2.0).

OPEN/

2 (x 1.5) and

3 (x

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Press

to view a different part of the frame.

You may move the frame from the center position to UP, DOWN,

LEFT or RIGHT direction.

POWER

INPUT

In the zoom mode press ZOOM repeatedly to return to a 1:1

view (

Off).

TV VOL

TIMER

TV/VCR

PLAY

Locating Desired Scene

Use the title, chapter and time recorded on the disc to

locate the desired point to play back.

STOP

SKIP

/INDEX

To check the title, chapter and time, press OSD. (see page 52)

ENTER/

SELECT

SET

Press SEARCH MODE during

playback or stop mode.

Jump

Time

Title

Chapter

SET UP

CANCEL

/Enter/0 9/Cancel/Jump

VCR/DVD/TV

Press

to select the “Time”, “Title” or “Chapter”.

Press Number keys to change the number.

• If you input a wrong number, press CANCEL.

• Refer to the package supplied with the disc to check the

numbers.

Note:

•

You can use the Pause, Slow, Search

or Skip feature in the zoom mode.

However, you cannot zoom in during

the Search playback.

In case of the Video-CD playback with

PBC, the SEARCH MODE does not

work.

Press ENTER.

Playback starts.

•

• When you change the title, playback starts from Chapter 1 of

the selected title.

• Some discs may not work in the above operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Repeat playback

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Title, Chapter, Track Playback

POWER

VCR

DVD

Press PLAY MODE during playback or stop mode.

DVD

Repeat

Off

Play Mode

Repeat

Off

/Enter/Play Mode

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

Press ENTER once or twice to select “Chapter” or “Title”.

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

In case of CD, at first press

to select “Repeat” and then press

ENTER once or twice to select “Track” or “All”.

POWER

DVD

INPUT

Repeat

Chapter

Play Mode

Repeat

Off

All

/Enter/Play Mode

TV VOL

/Enter/Play Mode

TIMER

TV/VCR

PLAY

Press PLAY MODE again to make the screen disappear.

STOP

• Press PLAY to start Repeat playback.

• To resume normal playback, select Repeat Off.

SKIP

/INDEX

ENTER/

SELECT

SET

SET UP

CANCEL

A-B Repeat Playback

A-B repeat playback allows you to repeat material between two

selected points.

Press REPEAT A-B during

playback.

The start point is selected.

VCR/DVD/TV

Note:

•

Some discs may not work with the

repeat operation.

In A-B repeat mode, subtitles near

point A or B may not appear.

During the A-B Repeat Playback the

ANGLE feature will not operate.

You may not be able to set A-B Re-

peat, depending on the scenes of the

DVD.

Press REPEAT A-B again.

The end point is selected.

Playback starts at the point that

you selected. Playback stops at

the end point, returns to Point A

automatically, then starts again.

A B

•

A-B repeat does not work with an in-

teractive DVD, MP3-CD and Video-CD

with PBC.

To resume normal playback press REPEAT A-B again.

“

” appears on the screen.

Off

Download from Www.Somanuals.com. All Manuals Search And Download.

Program playback/Random playback (CD)

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Program playback

You can arrange the order of tracks on the disc.

POWER

VCR

DVD

Press PLAY MODE in the stop

mode.

Play Mode

Repeat

Off

/Enter/Play Mode

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Press ENTER repeatedly until

the Program table as right

appears.

Play Mode

Repeat

Program

Off

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Quit

Program Playback

/Enter/0 9/Cancel/Play Mode

POWER

INPUT

Example: In case you wish to

program in order of 7, 3, 11:

Play Mode

Repeat

Program

Off

TV VOL

Enter as 7

, 3

, 11.

1 7

2 3

3 11

Quit

TIMER

TV/VCR

If you input a wrong number,

press CANCEL.

PLAY

Program Playback

/Enter/0 9/Cancel/Play Mode

STOP

Press

to select

4 _{“Program Playback” and press}

SKIP

Program Playback

/INDEX

ENTER. “Program Playback” will

appear on the screen. The

program you selected will begin

to playback in the order set.

ENTER/

SELECT

SET

SET UP

CANCEL

Toreturntonormalplayback,select

“Play Mode: Off” at step 2 above.

Random playback

VCR/DVD/TV

Press PLAY MODE in the stop

mode.

Play Mode

Repeat

Off

/Enter/Play Mode

Note:

•

To cancel program play, select “Quit”

at step 4 and press ENTER.

The program is cancelled when you

openthedisctrayorturnthepoweroff.

Random playback can not be

combined with Repeat playback.

Press

toselect“Random”.

Play Mode

Repeat

Random

Off

/Enter/Play Mode

Press PLAY.

“Random Play” will appear on the screen and Random Playback

will start.

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3 Playback

This player can play back the MP3-data

which has been recorded on CD-R or CD-

RW. To produce the MP3-data, you need a

Windows-PCwithCD-ROMdriveandaMP3-

encoding Software (not supplied).

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/

DVD. Then press DVD to select the DVD mode. (The DVD

indicator will light)

The Apple-HFS-System can not be played.

Press OPEN/CLOSE.

The disc tray will open.

Place a disc onto the tray.

MP3 CD Information

Limitations on MP3 CD playback

• MP3 CD is the disc that is standardized by

ISO9660, its file name must include 3-digits

extension letters, “mp3”.

Press PLAY or OPEN/CLOSE.

The disc tray closes automatically.

On the TV-screen, “Reading” and

then reading file number will

appear. Reading will take as much

time as the number of file.

Reading

MP3 15

• The directory and file names of the MP3

CD must be correspond to the ISO

standardized files.

• This unit can read 200 files per disc. If

one directory has more than 200 files, it

reads up to 200 files, the remaining files will

be omitted.

A MP3 menu screen will appear

on the TV screen.

Jazz

• As for multi-session disc, only the first

session can be played.

Track 1/12

01:28

Japan

Pops

Japan

Bay Bridge

BLUE EYES

Blurry Eyes

Press

folder.

or ENTER to select

• If the CD has both audio tracks and MP3

files, only audio tracks are played.

• It may take more than one minute for this

unit to read MP3 files depending on its

structure.

CLOSE MY EYES

DIVE TO BLUE

flower

Lies and Truth-

Honey

10 winter fall

/0-9/Enter/Play Mode

• Music recorded by “Joliet Recording

Specification” can be played back, the file

name is displayed (within 17 letters) on the

screen Long file names will be condensed.

• The music files recorded by “Hierarchical

File System” (HFS) cannot be played.

Press

or Number keys to select the desired

track, then press ENTER. Track is selected and play

commences.

• In case the folder includes more than 11 tracks, press

to display next track list.

Jazz

Track 1/12

01:28

Japan

Track 1/12 01:28

Pops

Japan

Pops

Limitations on display

Japan

Bay Bridge

BLUE EYES

Blurry Eyes

11 Mother

12 Hold Your Last

• The maximum number for display is 17

letters. Available letters for display are the

following: capital or small alphabets of A

through Z, numbers of 0 through 9, and _

(under score).

CLOSE MY EYES

DIVE TO BLUE

flower

Lies and Truth

Honey

10 winter fall

/0-9/Enter/Play Mode

• Other letters than those above are replaced

in hyphen.

Press STOP to end playback.

• The unit records the stopped point. “ ” appears on the

screen. Press PLAY to resume playback (from the scene

point).

• If you press STOP again or unload the disc, the unit will

clear the stopped point.

Notes on MP3 files

To play back MP3 CD in the recorded order,

1. Use MP3 software that records data

alphabetically or numerically.

2. Name each file including two-digit or three-

digit number (e.g. "01" "02" or "001" "002").

3. Refrain from making too many sub-folders.

Then press OPEN/CLOSE.

The disc tray opens.

Remove the disc and press POWER.

The disc tray closes automatically and DVD/VCR turns off.

CAUTION:

• Some MP3 CDs can not be played back

depending on the recording conditions.

• The CD-R/RW that has no music data or

non-MP3 files can not be played back.

Note:

•

During MP3-Playback, you can not use SEARCH, A-B

Repeat functions.

•

You can use Repeat(Track or All) and Random functions for

MP3 CD Playback.(See page 40 and 41)

Download from Www.Somanuals.com. All Manuals Search And Download.

Marking Desired Scenes

The unit stores the points that you

want to watch again up to 3 points.

You can resume playback from

each scene.

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Marking the Scenes

POWER

VCR

DVD

Press MARKER during

playback.

Marker

/Enter/Cancel/Marker

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Select the blank Marker using

ZERO RETURN

Marker

00 27 54

MODE

SUB TITLE

ThenpressENTERatthedesired

scene.

SP/EP

PLAY

/Enter/Cancel/Marker

REPEAT

A-B

ZOOM

TITLE

MODE

• Repeat this procedure to set

the other 2 scenes.

POWER

INPUT

Press MARKER to remove this display.

TV VOL

TIMER

TV/VCR

PLAY

Returning to the Scenes

PressMARKERduringplayback

or stop mode.

Marker

00 27 54

STOP

16 25

08 31

/Enter/Cancel/Marker

SKIP

/INDEX

ENTER/

SELECT

SET

SET UP

CANCEL

Press

1-3.

to select the Marker

Marker

00 27 54

16 25

08 31

/Enter/Cancel/Marker

VCR/DVD/TV

Press ENTER.

Playback starts from the marked scene.

Note:

•

Some discs may not work with the

marking operation.

The marking is canceled when you

open the disc tray or turn the power off.

Some subtitles recorded around the

marker may fail to appear.

WhiletheMARKERscreenisdisplayed,

ifyoudoaspecialplaybackastheFast

Forward/Review Playback

or SKIP, the MARKER screen will

disappear. Press MARKER again as

soon as you find the desired scene.

To Cancel the Mark

Press MARKER.

Press

to select the Marker 1-3.

Press CANCEL.

To remove this display, press MARKER.

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing soundtrack language / Subtitles

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

Changing soundtrack language

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

You can select the language when you play a multilingual disc.

POWER

Press A.MONITOR during

playback.

Thecurrentsoundtracklanguage

will appear.

2/8 Fra DolbyDigital

INPUT

TV VOL

TIMER

TV/VCR

PLAY

Press A.MONITOR repeatedly

until the desired language is

selected.

The on-screen display will

disappear after a few seconds.

1/8 Eng DolbyDigital

STOP

SKIP

/INDEX

ENTER/

SELECT

SET

SET UP

CANCEL

In case of VIDEO CD playback

AudiotypechangesasfollowseachtimeyoupressA.MONITOR.

VCR/DVD/TV

Turning the Subtitles On and Off

When playing back a disc recorded with subtitles, you can turn

the subtitles on or off.

Note:

Press SUB TITLE during playback

until “OFF” appears.

•

If the desired language is not heard

after pressing the button several times,

the language is not recorded on the disc.

Changing soundtrack or subtitle

language is cancelled when you open

the disc tray or turn the power off. The

initial default language or available

language will be heard and seen if the

disc is played back again.

Off

•

Changing the subtitle language

•

Depending on the DVD you may be

unable to turn on, turn off, or change the

subtitles, even if they are recorded on

the disc. While playing the DVD, the

subtitle may change while opening or

closing the disc tray, or while changing

the title.

In some cases, the subtitle language is

not changed to the selected one

immediately.

You can select the language when playing back a disc

recorded with multi-lingual subtitles.

Press SUB TITLE repeatedly during

playbackuntilyourdesiredlanguage

appears.

The on-screen display will disappear

after a few seconds.

1/32 Eng

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing angles / Title selection / DVD menu

Preparation:

• Turn ON the TV and set it to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Changing Angles

POWER

VCR

DVD

When playing back a disc recorded with multi-angle facility, you

can change the angle that you are viewing the scene from.

Press ANGLE during playback.

The current angle will appear.

1/9

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Press ANGLE repeatedly until the desired angle is selected.

POWER

INPUT

Title Selection

Two or more titles are recorded on some discs. If the title menu

TV VOL

TIMER

TV/VCR

is recorded on the disc, you can select the desired title.

PLAY

Press TITLE during playback.

Title menu appears on the screen.

STOP

• Press TITLE again to resume playback at the scene when you

pressed TITLE.

SKIP

/INDEX

Press

to select the desired title.

ENTER/

SELECT

SET

Press ENTER or PLAY.

The playback of the selected title will start.

SET UP

CANCEL

DVD Menu

Some DVDs allow you to select the disc contents using the

menu.

VCR/DVD/TV

When you play back these DVDs, you can select the subtitle

language and sound-track language,etc. using the DVD menu.

Press DVD MENU during playback.

Note:

The DVD menu appears on the screen.

Depending on the DVD, you may not

be able to change the angles even if

multi-angles are recorded on the disc,

or you may be unable to select the title,

and a "title menu" may simply be called

a "menu" or "title" in the instructions

supplied with the disc.

• Press DVD MENU again to resume playback at

the scene when you pressed DVD MENU.

Press

to select the desired item.

Press ENTER.

The menu continues to another screen. Repeat steps 2 and 3 to

set the item completely.

Download from Www.Somanuals.com. All Manuals Search And Download.

Parental control

Somediscsarespecifiednotsuitable

for children. Such discs can be

prevented from play back with the

unit.

Preparation:

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Parental control setting

POWER

VCR

Language Picture

Password

Parental

Other

DVD

Press SETUP MENU in the stop mode.

Press or to select “Parental”.

Then press ENTER.

Parental

9/Cancel

/Enter/Setup/Return

Press

to select “Parental 8”,

Language Picture

Password

Parental

Other

OPEN/

then press ENTER until the level you

desire appears (e.g.: 1).

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

Parental

ZERO RETURN

MODE

SUB TITLE

SP/EP

/Enter/Setup/Return

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

POWER

Press

once to select “Password

”.

Language Picture

Parental

Other

Then press Number keys to input a 4-

digit password (e.g.: 1234).

INPUT

Password

Parental

1234

• If you input a wrong number, press

CANCEL.

• Be sure to remember this number!

TV VOL

9/Cancel

/Enter/Setup/Return

TIMER

TV/VCR

PLAY

Level 1: DVD software for adults cannot be played back.

Level 8: All DVD software can be played back.

STOP

Select from level 1 to level 8.

On a scale of 1-8, "1" is the most restrictive.

SKIP

/INDEX

Language Picture

Parental

Other

Press ENTER.

1234

change to

Password

ENTER/

SELECT

SET

Parental

SET UP

CANCEL

9/Cancel

/Enter/Setup/Return

To make SETUP screen disappear, press SETUP MENU.

Note:

To unlock the Parental Control Setting

• If each setup (page 46~52) has been

completed, the unit can always be

worked under the same conditions

(especially with DVD discs).

Each setup will be retained in the

memory if you turn the power off.

• Depending on the discs, the unit can-

not limit playback.

• Some discs may not be encoded with

specific rating level information though

its disc jacket says "adult". For those

discs, the age restriction will not work.

• Do not forget the password. If you forget

the password, contact customer service.

Cancel the password so as to set the Parental level freely again,

Language Picture

Parental

Other

Select “Password

and press Number keys to input your

4-digit password.

” (step 1)

Password

Parental

1234

Then press ENTER.

9/Cancel

/Enter/Setup/Return

If the input password was right,

will appear.

You can move to “Parental 1”(e.g.) to

input the desired level or to cancel

parental control.

Language Picture

Password

Parental

Other

Parental

9/Cancel

/Enter/Setup/Return

Download from Www.Somanuals.com. All Manuals Search And Download.

Temporary disabling of rating level by DVD disc

Depending on the DVD disc, the

Preparation:

disc may try to temporarily cancel

the rating level that you have set.

It is up to you to decide whether to

cancel the rating level or not.

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

LoadaDVDdiscandpressPLAY

or OPEN/CLOSE (see page 37).

POWER

VCR

DVD

If the DVD disc has been designed to temporarily cancel the

Rating level, the screen which follows the “Reading” screen will

change, depending on which disc is played. If you select “YES”

with ENTER key, “Your disc exceeds the parental control level

1.”(e.g.) screen will then appear.

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

Reading

Your disc exceeds

the parental control level 1.

POWER

Parental Control Level

Cancel Picture

INPUT

/Enter/Return

TV VOL

TIMER

TV/VCR

If you wish to cancel the set rating level temporarily, select

PLAY

“Parental Control Level” with

, then press ENTER. If

the 4-digits password at step 3 on page 46 has been set, the

password entering screen will appear as shown in step 4 below.

Alternatively, if the password has not been set, playback will

commence. If you don’t know (or have forgotten) the password,

select “Cancel Picture”.

STOP

SKIP

/INDEX

The setting screen will disappear. Press OPEN/CLOSE to

remove the disc.

ENTER/

SELECT

SET

SET UP

CANCEL

Enter the password with

Number buttons (0-9).

Then press ENTER.

Please enter the

digit password

Enter/0 9/Cancel/Return

If you interrupt the entering,

press RETURN.

VCR/DVD/TV

Playback will commence if the entered password was correct.

Note:

This temporary cancellation of rating

level will be kept until the disc is ejected.

When the disc is ejected, the original

rating level will be set again

automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting menu language

You can select the language of the

Preparation:

disc menu messages of DVDs.

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Press SETUP MENU in the stop

mode.

Language Picture

Parental

Other

POWER

VCR

DVD

Press

to select

“Language”.

/Enter/Setup/Return

Press ENTER.

Then press

“Menu”.

Language Picture

Parental

Other

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

to select

ZERO RETURN

Subtitle

Audio

English

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

/Enter/Setup/Return

POWER

INPUT

Press ENTER.

Language Picture

Parental

Other

Press

to select your

English

Francais

Espanol

Other

TV VOL

Subtitle

Audio

English

desired language, then press

ENTER.

TIMER

TV/VCR

PLAY

9/Cancel

/Enter/Setup/Return

STOP

English, Francais, Espanol

The selected language is the first-priority Menu language.

SKIP

/INDEX

OTHER: Other language can be selected (See the Language

ENTER/

SELECT

SET

Code List on page 53).

SET UP

CANCEL

To make SETUP screen disappear, press SETUP MENU.

VCR/DVD/TV

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting subtitle language

The same subtitle language can

always be selected even if you replace

the disc or turn the power off.

Preparation:

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Press SETUP MENU in the stop

mode.

Language Picture

Parental

Other

POWER

VCR

DVD

Press

to select

“Language”

/Enter/Setup/Return

OPEN/

Press ENTER.

Language Picture

Parental

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

Then press

to select

Subtitle

Audio

English

MODE

SUB TITLE

“Subtitle”.

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

POWER

/Enter/Setup/Return

INPUT

Press ENTER.

Language Picture

Parental

Press

to select your

TV VOL

Subtitle

Audio

English

Francais

Espanol

Other

TIMER

desired language, then press

ENTER.

TV/VCR

PLAY

9/Cancel

Automatic

Off

/Enter/Setup/Return

STOP

English, Francais, Espanol

SKIP

/INDEX

The subtitle is displayed with the selected language if it is

recorded on the disc.

ENTER/

SELECT

SET

OTHER:

SET UP

CANCEL

If you want to select another language, enter the language code

(see the language code list on page 53).

AUTOMATIC:

• The unit will automatically select the same language in the

AUDIO setting.

• When the unit selects the same language as the AUDIO, the

subtitles will not appear during playback.

VCR/DVD/TV

• When you do not use the same language as the AUDIO, the

subtitles will appear during playback.

Off:

Note:

Subtitles do not appear.

If the selected language is not recorded

on the disc, the first-priority language is

selected.

To make SETUP screen disappear, press SETUP MENU.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting audio soundtrack language / Setting surround sound

Preparation:

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Setting audio soundtrack

language

Thesameaudiosoundtracklanguage

can always be selected by your unit

even if you replace the disc or turn

Press SETUP MENU in the stop

mode.

Press or

Language Picture

Parental

Other

the power off.

toselect“Language”

/Enter/Setup/Return

Press ENTER.

Then press

“Audio”.

Language Picture

Parental

to select

OPEN/

Subtitle

Audio

English

DVD MENU

DISPLAY

MARKER

RETURN

C.RESET

ANGLE

A.TRK

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

/Enter/Setup/Return

Press ENTER.

Press

desired Audio Language, then

POWER

Language Picture

Parental

to select your

Subtitle

Audio

English

Francais

Espanol

Other

INPUT

press ENTER.

9/Cancel

Original

TV VOL

/Enter/Setup/Return

TIMER

TV/VCR

PLAY

• English, Francais, Espanol:

The language you have selected will play if it is recorded on

the disc.

STOP

• OTHER: If you want to select another language,

enter the language code (See the Language Code List on page

53).

SKIP

/INDEX

• ORIGINAL: The unit will select the first priority language of

each disc.

ENTER/

SELECT

SET

SET UP

To make SETUP screen disappear, press SETUP MENU.

CANCEL

Setting surround sound

This DVD/VCR equipped with a “SPATIALIZER 3-D STEREO”

as the SURROUND option in the VCR menu. It can produce the

effect of being in a cinema or a concert hall.

VCR/DVD/TV

Since the SURROUND option exists in the VCR menu, the setting

is possible only during a disc-playback or in the VCR mode.

Note:

During disc-playback press SETUP MENU.

•

If the selected language is not

recorded on the disc, the original

language will be heard.

Press

to select

TIMER REC SET

AUTO REPEAT

SAP

SURROUND

CH SET UP

SYSTEM SET UP

SURROUND.

Then press ENTER to select [ON]

or [OFF].

•

The “SPATIALIZER 3-D STEREO” is

effective only for the sound of disc.

ON OFF

To cancel Surround mode:

⟨+/-/ENTER/MENU⟩

Follow the right steps 1~2, then press

ENTER to select the OFF position.

Press SETUP MENU to return to the TV.

Press SETUP MENU until the menu screen is cleared.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the aspect ratio of TV screen

You can select the aspect ratio for

Preparation:

your TV.

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Press SETUP MENU in the stop

mode.

Language Picture

Parental

Other

POWER

VCR

DVD

Press or

toselect“Picture”.

/Enter/Setup/Return

OPEN/

Press ENTER, then press

to select “Tv Screen”.

Language Picture

Parental

DVD MENU

MARKER

A.TRK

RETURN

C.RESET

ANGLE

DISPLAY

ZERO RETURN

Tv Screen

Display

4:3

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

POWER

/Enter/Setup/Return

INPUT

Press ENTER.

Language Picture

Parental

Press

to select your

TV VOL

Tv Screen

Display

4:3

16:9

desired screen type, then press

ENTER.

TIMER

TV/VCR

PLAY

/Enter/Setup/Return

STOP

You have the following screen sizes to choose from:

SKIP

/INDEX

4:3

Select this mode when connecting to a conventional TV. When

playing back a wide screen-DVD disc, it displays the wide picture

with black bands at the top and bottom of screen.

ENTER/

SELECT

SET

SET UP

CANCEL

4:3

PAN SCAN

It displays the wide picture on the whole screen with left and

right edges automatically cut off.

16:9

WIDE SCREEN

VCR/DVD/TV

Select this mode when connecting to a wide-screen TV.

A wide screen picture is displayed full size.

To make SETUP screen disappear, press SETUP MENU.

Note:

If the DVD disc is not formatted in the pan

& scan style, it displays 4:3 style.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting on Screen display / Status display of Disc

On screen display can be switched on

Preparation:

or off when you press the buttons.

• Turn ON the TV and set to the video input mode.

• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

Then press DVD to select the DVD mode. (The DVD indicator will light)

Press SETUP MENU in the stop

mode.

Language Picture

Parental

Other

POWER

VCR

DVD

Press

to select “Picture”

/Enter/Setup/Return

Press ENTER, then press

Language Picture

Parental

2 _{to select “Display”.}

Tv Screen

Display

4:3

OPEN/

DVD MENU

DISPLAY

MARKER

A.TRK

RETURN

C.RESET

ANGLE

ZERO RETURN

MODE

SUB TITLE

SP/EP

PLAY

REPEAT

A-B

ZOOM

TITLE

MODE

/Enter/Setup/Return

POWER

Language Picture

Parental

Press ENTER to select “On” or

“Off”.

Tv Screen

Display

4:3

Off

INPUT

TV VOL

TIMER

TV/VCR

/Enter/Setup/Return

PLAY

On: On screen displays appears when you press the any

buttons (factory setting).

STOP

Off: On screen displays do not appear when you press any

buttons except SETUP MENU, SEARCH MODE, PLAY

MODE, MARKER and OSD.

SKIP

/INDEX

To make SETUP screen disappear, press SETUP MENU.

ENTER/

SELECT

SET

SET UP

CANCEL

Status display of Disc

Each Press of OSD, the status display of the disc will appear on the

screen and change as follows.

DVD

00:34:56 01:12:33

Title

1/99 Chapter 1/999

1/9

VCR/DVD/TV

1/8 Eng DolbyDigital

1/32 Eng

VIDEO

00:09

34:56

04:35

71:33

PBC

Track —/—

00:12

34:56

04:32

AUDIO

71:33

Track 11/99

To make status display disappear, press OSD again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Language Code List

Enter the appropriate code number for the initial settings "Audio", "Subtitle" and/or "Menu" (see pages 48-

50).

Language Name Code Language Name Code Language Name Code Language Name Code

Abkhazian

Afar

1112 Fiji

1620 Lingala

1619 Lithuanian

1628 Macedonian

1635 Malagasy

1722 Malay

2224 Singhalese 2919

1111 Finnish

1116 French

2927 Frisian

1123 Galician

1128 Georgian

1835 German

1129 Greek

1135 Greenlandic

1136 Guarani

1211 Gujarati

1531 Hausa

2230 Slovak

2321 Slovenian

2317 Somali

2329 Spanish

2921

2922

2925

1529

Afrikaans

Albanian

Amharic

Arabic

2111 Malayalam

1415 Maltese

1522 Maori

2322 Sundanese 2931

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

2330 Swahili

2319 Swedish

2328 Tagalog

2325 Tajik

2933

2932

3022

3017

3011

3030

3015

3018

1225

3019

3025

3028

3021

3033

3121

3128

3136

2122 Marathi

1724 Moldavian

1731 Mongolian

1811 Nauru

2324 Tamil

Basque

2411 Tatar

Bengali; Bangla 1224 Hebrew

1933 Nepali

2415 Telugu

2425 Thai

Bhutani

Bihari

1436 Hindi

1819 Norwegian

1831 Oriya

1218 Hungarian

1228 Icelandic

1217 Indonesian

2335 Interlingua

1215 Irish

2528 Tibetan

2611 Tigrinya

2629 Tonga

1611 Turkish

2622 Turkmen

2630 Twi

Breton

1929 Panjabi

1924 Pashto, Pushto

1911 Persian

1711 Polish

Bulgarian

Burmese

Byelorussian

Cambodian

Catalan

Chinese

Corsican

Croatian

Czech

2123 Italian

1930 Portuguese

2011 Quechua

1311 Japanese

3618 Javanese

1325 Kannada

1828 Kashmiri

1329 Kazakh

1411 Kirghiz

2422 Korean

1524 Kurdish

1525 Laothian

1530 Latin

2731 Ukrainian

2033 Rhaeto-Romance 2823 Urdu

2124 Romanian

2129 Russian

2121 Samoan

2135 Sanskrit

2125 Scots Gaelic

2131 Serbian

2825 Uzbek

2831 Vietnamese 3219

2923 Volapük

2911 Welsh

1714 Wolof

2928 Xhosa

2918 Yiddish

2924 Yoruba

2914 Zulu

3225

1335

3325

3418

2019

3525

3631

Danish

Dutch

English

Esperanto

Estonian

Faroese

2225 Serbo-Croatian

2211 Shona

1625 Latvian, Lettish 2232 Sindhi

Download from Www.Somanuals.com. All Manuals Search And Download.

Problems and troubleshooting

Use the following check list for troubleshooting when you have problems with your unit. Consult your local

dealer or service outlet if problems persist.

Be sure all connections are properly made when using with other units.

SYMPTOMS

DVD/VCR

POSSIBLE SOLUTIONS

PAGE

•Make sure the power cord is plugged in.

•Try another AC outlet.

–

•Power is off, check fuse or circuit breaker.

•Unplug unit, then plug it back in.

–

DVD/VCR does not operate.

•Select the DVD or VCR mode before operating.

•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.

18,36

•

Antenna connection is not correct or antenna cable is disconnected.

12~15

• The video channel is not in the correct position or the TV is not

set to the video channel 3 or 4.

• Check the unit is connected correctly.

• The video input selector of the TV is not set to VIDEO. Set to

VIDEO (or equivalent).

12~17

No picture.

No sound.

–

• Channel is set to the external mode.

–

• Check the unit is connected correctly.

• Check the input selector of the amplifier is set properly.

• The unit is in the Special playback mode.

12~17

–

26,38

• Aim at the remote control at the remote sensor.

• Operate within Approx. 5 Meters or reduce the light in the room.

• Clear the path of the beam.

• The batteries are weak. Replace the batteries.

• Check the batteries are inserted correctly.

• Check the frequency code is set correctly.

The remote control does not

function.

The DVD-keys on the RCU of the

other JVC RECEIVER/TV is not

effective.

•This is not a defect. Since this unit is combined type of DVD

and VCR, the remote code of DVD is individual.

14,15

•Check all CATV connections.

•Station or CATV system problems, try another station.

No CATV reception

•During the Auto Clock operation, a video signal can be put out.

Please set the clock with Manual clock setting or wait until the

Auto Clock operation completed.

No POWER but a picture appears

on the TV screen.

VCR

•The erase prevention tab of the video cassette is broken off.

•The unit is in the external input mode.

TV recording does not work.

24,28

• The time is not set correctly.

• The recording start/end time is not set correctly.

• The TIMER has not been pressed ( is not lit).

21,23

Timer recording does not work.

• Tracking adjustment beyond range of automatic tracking circuit.

Try Manual tracking adjustment.

• Video heads are dirty.

Noise bars on screen.

–

• The tape is worn or damaged.

DVD

Display is not shown in your

language.

•Select proper language in the menu options.

• No disc is inserted.

• The disc may be dirty. Clean up the disc.

• The unit cannot play DVD-ROMs, etc.

Playback doesn’t start.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problems and troubleshooting / Video head cleaning

SYMPTOMS

POSSIBLE SOLUTIONS

PAGE

Stopping playback, search, slow-

motion play, repeat play, or program

play, etc. cannot be performed.

–

• Some discs may not do some of the functions.

No 4:3 (16:9) picture

No on-screen display

No surround sound

• The setup does not match your TV.

• Select Display On.

• The setup does not match your stereo system.

The unit or remote operation key

is not functioning.

• Turn off the unit and unplug the AC power cord for several

minutes, then replug it.

–

Playback does not start when the

title is selected.

• Check the Parental setup.

Audio soundtrack and/or subtitle

language is not changed when you

play back a DVD.

49,50

• Multilingual language is not recorded on the DVD disc.

• Some discs have no subtitles.

• Subtitles are cleared. Press SUB TITLE.

No subtitle

Angle cannot be changed.

appears on the screen.

• Multi-angles are not recorded on the DVD disc.

• The function is prohibited with the unit or the disc.

–

Video head cleaning

Video head clogging

The video heads are the means by which the DVD/VCR reads

the picture from the tape during playback. In the unlikely event

that the heads become dirty enough to be clogged, no picture

will be played back. This can easily be determined if, during

playback of a known good tape, there is good sound, but no

picture (picture is extremely snowy). If this is the case, have

the DVD/VCR checked by qualified service personnel.

Good Picture

Snowy Picture

NOTES: DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE

•

REAR COVER.

Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.

To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.

•

Notes

Auto Clock Setting

Notes for Canadian customers regarding the clock feature of the your DVD/VCR.

The XDS signals are carried only by certain broadcast television stations (for example, the signal is carried by

most Public Broadcasting Service stations). You must be able to receive a station carrying the XDS signal to

use the Auto Clock Setting to set your DVD/VCR’s internal clock. If you live in an area that does not broadcast

XDS signals, you must set the clock manually. Please see page 23 for instructions on how to manually set your

DVD/VCR’s clock.

Special note for residents of Newfoundland:

The Auto Clock Setting cannot be used to set the DVD/VCR’s internal clock to Newfoundland time. The time

zone command does not include a setting for the Newfoundland time zone. Trying to use the Auto Clock Setting

in the Newfoundland time zone could result in an incorrect time setting or no setting at all. Please set your DVD/

VCR’s clock using the Manual Clock Setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

GENERAL

Power supply:

AC 120V 60Hz

Power consumption:

Operation: 20W

Stand by: 3W

Weight:

9.9lbs (4.5 kg)

Dimensions:

Width : 16-15/16 inches (430 mm)

Height: 3-7/8 inches (99 mm)

Depth : 12-1/4 inches (311 mm)

Inputs/Outputs:

Video:

In: 1Vp-p/75 ohm

Out: 1Vp-p/75 ohm

Audio:

In: -8 dBm/50K ohm

Out: -8 dBm/1K ohm

UHF/VHF IN/OUT: 75 ohm coaxial

Antenna:

Hi-Fi Frequency Response: 20Hz to 20,000Hz

Hi-Fi Dynamic Range:

More than 90dB

VCR section

Video Head:

Audio Track:

Tuner:

4 Rotary Heads

Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track

181 Channel Freq. Synthesized

VHF

UHF

2-13

14-69

CATV 14-36 (A)-(W)

37-59 (AA)-(WW)

60-85 (AAA)-(ZZZ)

86-94 (86)-(94)

95-99 (A-5)-(A-1)

100-125 (100)-(125)

01 (5A)

RF Channel Output:

F.FWD/REW Time:

Channel 3 or 4, Switchable

Approx. 1minutes and 48 seconds (with T-120 Cassette Tape) (at+25°C)

DVD section

Signal system:

Applicable disc:

Audio characteristics:

Frequency response:

S/N Ratio:

NTSC

DVD (12cm, 8cm), CD (12cm, 8cm)

DVD: 4Hz - 22KHz

CD: 4Hz - 20KHz

90dB

Harmonic distortion:

Wow and flutter:

Dynamic range:

Output:

0.01%

Below Measurable Level

90dB

Video : (RCA) 1 Vp-p/75ohm

Audio : (RCA) -8 dBm/1Kohm

Digital Audio : 0.5Vp-p 75 ohm

CD : Wavelength: 775 - 805 nm

Maximum output power: 0.5 mW

DVD : Wavelength: 640 - 660 nm

Maximum output power: 1.0 mW

Pickup:

ACCESSORIES:

Remote control x 1

Batteries (2 x AA)

75 ohm Coaxial Cable x 1

AUDIO/VIDEO Cable x 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Memo

Download from Www.Somanuals.com. All Manuals Search And Download.

FOR SERVICING (Only in U.S.A.)

HOW TO LOCATE YOUR JVC SERVICE CENTER

TOLL FREE: 1-800-537-5722

http://www.jvc.com

Dear Customer,

In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating

the unit. In the event that repair is necessary, or for the address nearest your location within the Continental

United States, please call 1-800-537-5722 for your nearest authorized servicer or visit our website at

www.JVC.com. Remember to retain your Bill of Sale for Warranty Service.

— JVC

JVC SERVICE & ENGINEERING

COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering

and production of the wide array of JVC products, service is the key to maintaining the high level performance

for which JVC is world famous. The JVC service and engineering organization stands behind our products.

NATIONAL HEADQUARTERS

JVC SERVICE & ENGINEERING COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.

10 New Maple Avenue

Pine Brook, NJ 07058-9641

Don’t service the product yourself.

ACCESSORIES

To purchase accessories for your JVC product, you

may contact your local JVC Dealer.

From the 48 Continental United States call toll free:

1-800-882-2345 or on the web at www.JVC.com

Please refer to qualified service personnel for repairs.

CAUTION

To prevent electrical shock, do not open the cabinet.

There are no user serviceable parts inside.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY (Only in U.S.A.)

LIMITED WARRANTY

CONSUMER VIDEO 1-90

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE

ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the

date of original retail purchase for the period as shown below. (“The Warranty Period”)

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIAAND

IN COMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO:

If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such

repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service

centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts

thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen

size 25 inches and above which are covered on an in-home basis.

WHAT YOU MUST DO FOR WARRANTY SERVICE:

Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized

service center, please call toll free: (800) 537-5722.

If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy

of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and

location of which will be given to you by the toll-free number.

If you have any questions concerning your JVC Product, please contact our Customer Relations Department.

WHAT IS NOT COVERED:

This limited warranty provided by JVC does not cover:

1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty

installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by

JVC to render such service, or if affixed to any attachment not provided with the products, or if the model or serial

number has been altered, tampered with, defaced or removed;

2. Initial installation and installation and removal for repair;

3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;

4. Damage that occurs in shipment, due to act of God, and cosmetic damage;

5. Signal reception problems and failures due to line power surge;

6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;

7. Accessories;

8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);

There are no other express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY,

IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.

JVC SHALLNOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS ORANY OTHER

DAMAGES, WHETHER DIRECT, INCIDENTALOR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE

TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY

BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD

SET FORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied

warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state.

JVC COMPANY OF AMERICA

1700 Valley Road

DIVISION OF JVC AMERICAS CORP.

Wayne, New Jersey 07470

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR

DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT

WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the

cabinet. Retain this information for future reference.

Model No.:

Serial No.:

Purchase date:

Name of dealer:

Download from Www.Somanuals.com. All Manuals Search And Download.

VICTOR COMPANY OF JAPAN, LIMITED

2A30201B

01/12

Printed in Thailand

Download from Www.Somanuals.com. All Manuals Search And Download.

IRiver Portable CD Player iMP 400 User Manual
Jensen Flat Panel Television JE3208 User Manual
JL Audio Speaker XR650 CX User Manual
JVC Car Video System 0110NYMMDWJEIN User Manual
JVC DVD Player XV M556TN User Manual
Kenwood Car Amplifier KTC 1000R User Manual
Kenwood Stereo Amplifier KAC PS650D User Manual
Kenwood Stereo Amplifier KAC X1D User Manual
KitchenAid Ice Maker KUIS15NRTB2 User Manual
KitchenAid Trash Compactor 9871780C User Manual