CAUTION:
To prevent malfunction of the player
Connections
Before making connections:
• Do not connect the AC power cord until all other connections have been made.
• Connect VIDEO OUT of the player directly to the video input of your TV. Connecting VIDEO OUT of the
player to a TV via a VCR/an integrated TV/Video system may cause a monitor problem.
DVD PLAYER
XV-N330B
XV-N332S
Warnings, Cautions and Others
•Do not block the ventilation openings or holes. (If the •There are no user-serviceable parts inside. If
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
•Do not place any open flame sources, such as lighted•Do not insert any metallic objects, such as wires,
candles, on the apparatus.
•When discarding batteries, environmental problems
must be considered and local rules or laws governing
the disposal of these batteries must be followed strictly.
•Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect
from damage, locate the apparatus as follows:
anything goes wrong, unplug the power cord and
consult your dealer.
Connecting to a TV with component jacks
Connecting to a stereo audio amplifier (receiver)
PB
LEFT
Y
PB
LEFT
Y
XIAL
hairpins, coins, etc. into the player.
•Do not block the vents. Blocking the vents may
damage the player.
RIGHT
VIDEO
VIDEO OUT
PR
RIGHT
TREAM
L OUT
AUDIO OUT
INSTRUCTIONS
Connecting to a TV with SCART connector
VIDEO
VIDEO OUT
PR
AUDIO OUT
To analog
To analog audio input
To clean the cabinet
®
NOTE
audio input
•Use a soft cloth. Follow the relevant instructions on
the use of chemically-coated cloths.
•Do not use benzene, thinner or other organic solvents
and disinfectants. These may cause deformation or
discoloring.
TV
The VIDEO jack, AV OUT terminal, and
component (Y, PB, PR) jacks cannot be
used at the same time.
SCART cable
(not supplied)
Connecting to a digital audio device
V I D E O
IN
To enjoy high-quality surround sound, connect the
DIGITAL OUT (COAXIAL) jack to a Dolby Digital or DTS
decoder or an amplifier with a built-in decoder.
IN
To component
video input
S-VIDEO
GNT0068-005A[EK]
0206KTC-MW-SC
©2006 Victor Company of Japan, Limited
PB
VIDE
O
LEFT
Y
COAXIAL
To switch the scanning mode between Progressive and
Interlace, press and hold VFP-I/P on the remote control
for a few seconds.
Front:
No obstructions and open spacing.
EN
Playable discs
• DVD VIDEO, Audio CD, Video CD, SVCD
Sides: No obstructions in 3 cm from the sides.
RIGHT
PCM/STREAM
DIGITAL OUT
L
EF
T
VIDEO
VIDEO OUT
PR
Top:
Back:
No obstructions in 5 cm from the top.
No obstructions in 15 cm from the back.
A
AUDIO OUT
UDI
O
Region code of DVD VIDEO
This player can play back DVD VIDEO discs
whose region code numbers include “2.”
Examples of playable DVD VIDEO discs:
R
IGH
T
NOTES
To analog
Bottom: No obstructions, place on the level surface.
•Connect to a TV with composite jacks and set
[CONNECTIONS] to [VIDEO COMPONENT] before
connecting with component jacks. (See
“CONNECTIONS” in “Initial settings.”)
•Connect “Y” to “Y,”“PB” to “PB(CB),”“PR” to “PR(CR)”
correctly.
V I D E O
audio input
Spacing 15 cm or more
•DVD-R/-RW, +R/+RW written and finalized in the DVD
VIDEO format
XV-N330B/XV-N332S
AV OU
T
•CD-R/RW written in the SVCD, Video CD or Audio CD
format
•CD-R/RW written in MP3/JPEG in accordance with
the “ISO 9660” format
1 2
3 4
1 2 3
4 5 6
To digital audio input
Front
ALL
2 5
2
The player
Wall or
obstructions
NOTES
•The VIDEO jack, AV OUT terminal, and component
(Y, PB, PR) jacks cannot be used at the same time.
The player’s region code is printed on the rear of
the player
•Depending on the disc, no signal may be outputted
from the DIGITAL OUT. Make an analog connection
in this case.
•Set [DIGITAL AUDIO OUTPUT] in the [AUDIO]
preference display correctly according to the
connected digital audio equipment. (See “DIGITAL
AUDIO OUTPUT” in “Initial settings.”)
Stand height
Supported Digital audio formats:
Linear PCM, MPEG Multichannel, Dolby Digital, DTS (Digital
Theater Systems)*
5 cm or more
Floor
Note of Color system format
About the scanning mode indicator
This player accommodates the PAL system, and
also can play back discs recorded with NTSC
system. (NTSC video signals are converted to a
PAL signal and output.)
[PICTURE SOURCE] of
the PICTURE menu
Source type of DVD VIDEO
Connecting to a TV with composite jacks
Film source
[DDP]
Video source
[P]
CAUTION
NOTES
AUTO
FILM
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
3. The mains plug shall remain readily operable.
•If a disc gets dirty, scratched or warped, or due to the
disc characteristics or recording conditions, the
player may not be able to play back such discs.
•The player can play back audio signals recorded in
MIX-MODE CD, CD-G, CD-EXTRA and CD TEXT.
•With some discs, operations may not be possible.
* To play back DTS-encoded DVD VIDEO or DTS-
encoded Audio CD discs correctly, connect the
player to an amplifier with a built-in DTS decoder.
Otherwise, playback sound will be distorted.
TV
Precautions
NOTES
[DDP]
[DDP]
Notes on the power cord
•If your TV has a monaural audio input
instead of stereo, use an optional audio
cable which converts stereo audio
output to monaural.
VIDEO(NORMAL)/
(ACTIVE)
[P]
[P]
Supplied accessories
IN
•When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet. A
small amount of power (1.0 W) is always consumed while
the power cord is connected to the wall outlet.
•When unplugging the player from the wall outlet,
always pull the plug, not the power cord.
•Do not handle the power cord with wet hands.
•Disconnect the power cord before cleaning the
player or moving the player.
If anything is missing, consult your dealer
immediately.
VIDEO
RIG
NOTE
Some progressive TV and High-Definition TV sets are
not fully compatible with the player. To check the
compatibility of your TV, contact your local JVC
customer service center.
Caution ––
Disconnect the mains plug to shut the power off
completely. The STANDBY/ON button in any
position does not disconnect the mains line. The power
can be remote controlled.
STANDBY/ON button!
•Remote control (x 1)
•The VIDEO jack, AV OUT terminal, and
component (Y, PB, PR) jacks cannot be
used at the same time.
H
T
•R6(SUM-3)/AA(15F) battery (x 2)
AU
D
T
IO
LEF
Unplayable discs
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
•Do not alter, twist or pull the power cord, or put
anything heavy on it, which may cause fire, electric
shock, or other accidents.
If you try to play back discs listed below, noise may be
generated and causes damage to speakers.
• DVD-R/-RW written in the VR format
COAXIA
L
PR
PCM
2. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser
radiation when open. Do not stare into beam or view
directly with optical instruments.
/STREAM
DIGIT
Yellow
LEFT
•If the cord is damaged, consult a dealer and have the• DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM,
AL OU
VID
VDE
T
PB
RIGHT
power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
•Do not place the player in moist or dusty places.
PHOTO CD, SACD
• Unfinalized discs
• Discs of irregular shape or discs with tape, seals or
Audio/video cable
(not supplied)
O
O
T
AUDI
O
O
UT
The player
•If water gets inside the player, turn off the power and paste on either the label side or playback side.
Information for Users on Disposal of Old Equipment
[European Union Only]
Red
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.
remove the plug from the wall outlet, then consult
your dealer. Using the player in this state may cause
a fire or electrical shock.
Playing back these discs may damage the player.
White
This symbol indicates that product with this symbol
should not be disposed as general household
waste.If you want to dispose of this equipment,
please do not use the ordinary dust bin! There is a
separate collection System for these products.
The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
•Do not expose the player to direct sunlight or place it
near a heating device.
Notes on installation
•Select a place which is level, dry and neither too hot
nor too cold between 5˚C and 35˚C.
•Leave sufficient distance between the player and the TV.
•Do not install the player in a place subject to vibrations.
•Do not put heavy objects on the player.
5. This unit applies to the standard “IEC 60825-1: 2001”
for laser products.
1
2
3
4
Turning on the power
Initial setup
Basic Operations
Advanced Operations
When you turn on the player for the first time after
purchase, the following message appears on the TV
screen.
Changing the picture tone (VFP)
Changing the language, sound
Turning on and off the player
Inserting the AC power plug
Changing the display window
contents
and scene angle
After all other connections have been made, insert the
AC power plug to the wall outlet firmly.
The VFP (Video Fine Processor)
Insert a disc
STANDBY/ON
function allows you to adjust the
OPEN/
1 Press the button.
CLOSE
Each time you press DISPLAY,
the display window contents
changes.
Open/close the disc tray
Basic playback
EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO
SETTING
YES - PRESS ENTER NO - PRESS CANCEL
1 Press 0 to open the disc tray.
STANDBY/ON
picture character according to the
OPEN/
CLOSE
2 Press the button repeatedly or
2 Place a disc in the disc tray.
•To insert an 8-cm disc, place it in the inner
recess.
type of programming, picture tone or
+
–
SLOW
DISPLAY ON SCREEN
Turning on and off the player
Installing the batteries in the remote control
Open the compartment cover, and place the two
supplied R6(SUM-3)/AA(15F) batteries in the remote
control according to the polarity markings (“+” and “–”)
inside the compartment. Then replace the cover.
5/∞ to select the desired item.
3 Press ENTER to finish the
setting.
personal preferences.
+
–
SLOW
DISPLAY ON SCREEN
TOP
MENU
THUMBNAIL/
LIST
Before enjoying this player, make the initial settings as
follows:
1 Press VFP-I/P.
Buttons To do
TOP
MENU
THUMBNAIL/
LIST
Locating the beginning of a scene
or song
3 Press 0 to close the disc tray.
2 Press 2/3 to select the desired
Buttons
To do
3*
Start/resume normal Playback
Stop
•When RESUME is ON or DISC
RESUME, this player memorizes
the position on the disc where you
interrupted playback.
– To resume playback, press 3.
– To stop playback completely,
press 7 again.
ENTER
preset.
1 Press ENTER.
You can select a title/chapter/
track directly and start playback.
For DVD Video:
(While stopped) select title.
(While playing back) select
chapter.
ENTER
AUDIO
For DVD Video:
select audio languages.
For SVCD/VCD:
select the audio
channel.
7
Selected
Preset
DVD PLAYER SETUP
USER 1
GAMMA
MENU
SET UP
NEXT
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
ENGLISH
PREVIOUS SELECT
MENU
SET UP
NEXT
MID
PREVIOUS SELECT
BRIGHTNESS
+
4
CLEAR
CONTRAST
SATURATION
SHARPNESS
Y DELAY
+10
With the label side up
ON SCREEN LANGUAGE
ENGLISH
CLEAR
ENGLISH
FRENCH
GERMAN
+10
SUBTITLE select the subtitle.
ANGLE select the view-angle.
For SVCD/VCD/CD:
Select track.
1
4
2
5
8
0
3
6
LOW
1
4
2
5
8
0
3
6
+
2
2 Press 5/∞ to select the on-screen language for
To select 5: press 5.
8*
Pause
Parameter
7
9
the preference displays, etc., then press ENTER.
To select 23: press 2, then 3.
To select 40: press 4, then 0.
•If you press TITLE/GROUP
before entering the number, you
can select the title instead of the
chapter.
•Each time you press the button,
the still picture advances to the
next frame.
CANCEL
RETURN
7
9
NORMAL For watching TV in a
Changing the Sound Field
DVD PLAYER SETUP
CANCEL
RETURN
general room.
Each time you press SOUND
EFFECT, the Sound Effect mode
changes.
•As the value becomes bigger, the
Sound Effect works stronger.
TITLE/
GROUP
SOUND
EFFECT
MONITOR TYPE
PICTURE SOURCE
SCREEN SAVER
CONNECTIONS
BACKGROUND
4:3 L.B.
16:9
4:3 LB
Point toward the remote sensor
directly as possible (the operating
range is approx. 5 m.)
VFP DIMMER
I/P
CINEMA For watching a movie
software in a room with
suppressed light.
¡/1 Fast forward/backward
(While paused)
TITLE/
GROUP
SOUND
EFFECT
VFP DIMMER
I/P
4:3 PS
ANGLE SUBTITLE AUDIO ZOOM
SLIDE EFFECT
SCART RGB
STANDARD
Slow-motion playback
ANGLE SUBTITLE AUDIO ZOOM
SLIDE EFFECT
•Each time you press the button,
The batteries will last about six months with normal use.
If the functions of the remote control become erratic,
replace the batteries.
USER1
USER2
You can adjust
Using the disc menu
the playback speed changes.
parameters that affect the
picture character and
store the settings as a user
preset. See below.
You can operate a disc—SVCD/
VCD with Playback Control*
(PBC)—using the disc menu
shown on the TV screen.
* A method of controlling disc play
for SVCD/VCD by using the disc
menu.
¢/4 Skip chapter/track
3 Press 5/∞ to select the monitor type, then press
ENTER.
Main display
•If you press and hold the button during
playback, playback is advanced/
reversed at 5 times normal speed.
•Each indicator lights up when corresponding
function/mode is activated, or corresponding
information is on the main display.
Precautions of the safe use of batteries
•For a normal (conventional) TV, selec“t4:3 LB” or
“4:3 PS.” (See “MONITOR TYPE” in “Initial
settings.”)
Zooming the picture
Observe the following precautions for the safe use of
batteries. If they are used improperly their lives will be
shortened, they may burst or their contents may leak.
To adjust the picture tone
Each time you press ZOOM, the
magnification changes.
•You can use5/∞/2/3 button to
move the zoomed position.
To return to the normal playback,
select the normal size by pressing
ZOOM repeatedly.
VARIABLE (For DVD Video)
1 Select “USER1” or “USER2.”
2 Press 5/∞ to select a parameter, then press ENTER.
•For a wide-screen TV, selec“t16:9.”
PLAYBACK
You can change the playback
speed with the sound (except for
DTS) and subtitles.
•Remove the batteries from the remote control if it is
not going to be used for a long period of time.
•Remove dead batteries and dispose of them
properly.
•Never leave dead batteries lying around, take them
apart, mix them with other refuse, or throw them into
an incinerator.
•Never touch liquid that has leaked out of a battery.
•Do not mix new and old batteries, or batteries of
different types, when placing them.
DVD PLAYER SETUP
7 For DVD
GAMMA
Adjust this if the neutral color is bright or dark.
The brightness of dark and bright portion is
maintained (LOW/MID/HIGH).
DIGITAL AUDIO OUTPUT
DOLBY DIGITAL/PCM
When playing a disc with low quality recording
conditions or scratches
PCM ONLY
DOLBY DIGITAL/PCM
1 Press TOP MENU or MENU to show the disc menu.
2 Press 5/∞/2/3 to select a desired item, then press
ANALOG DOWNMIX
D.RANGE CONTROL
OUTPUT LEVEL
About On-screen guide icons
To playback 1.2 or 1.5 times
faster, press VARIABLE
PLAYBACK on the player or ¡
on the remote control.
To playback 0.8 or 0.6 times
slower, press ¡ on the remote
control while playback is paused.
STREAM/PCM
: Playback.
STANDARD
ENTER or 3 (SELECT).
If the disc is poorly recorded or the disc is of poor quality,
there may be problems with playback or discs cannot be
played back at all.
TRACK ADJUST function allows you to play back such
discs with better quality.
BRIGHTNESS Adjust this if the picture is bright or dark on the
•With some discs, you can also select items by entering the
number using the numeric buttons.
: Pause.
whole (–16 (darkest) to +16 (brightest)).
/
: Slow-motion playback with the current
speed.
CONTRAST
Adjust this if the far and near position is unnatural
(–12 to +12).
7 For SVCD/VCD
4 Press 5/∞ to select a desired digital output
signal type, then press ENTER.
1 While stopped, press TOP MENU or 3 (SELECT) to
show the menu.
2 Press the numeric buttons to select a desired item.
Each time you press TRACK ADJUST, the mode of the
function appears on the TV screen and changes as
follows:
/
: Fast forward/backward playback with the
current speed.
SATURATION Adjust this if the picture is whitish or blackish
Set this item correctly according to the logo on your
receiver or decoder.
(For SVCD/VCD)
The disc is played back at about
2 times faster than normal.
(–16 (blackest) to +16 (whitest)).
Turning on and off the player
To select 5: press 5.
(If you do not connect the player to such a device,
press ENTER to finish the setting.)
•Receiver/decoder bearing Dolby Digital logo and
no DTS, select “DOLBY DIGITAL/PCM.”
•Receiver/decoder bearing both Dolby Digital and
DTS logos, select “STREAM/PCM.”
Press
STANDBY/ON.
SHARPNESS* Adjust this if the picture is indistinct (LOW/HIGH).
: At the beginning of a scene containing multi-
angle views.
TRACK ADJUST OFF = TRACK ADJUST
MODE 1 = TRACK ADJUST MODE 2
To select 23: press 2, then 3.
To select 40: press 4, then 0.
•To move to the next or previous page of the current menu,
press ¢ or 4.
•To return to the previous menu, press RETURN.
(Only for DVD Video)
Y DELAY
Adjust this if the picture looks separately/
overlapped (–2 to +2).
The playback position moves back
10 seconds before the current
position (only within the same title).
Select TRACK ADJUST MODE1 or MODE 2 which gives
: At the beginning of a scene containing multi-
audio sounds.
you better results
.
To return to the normal playback mode, select
TRACK ADJUST OFF.
* Adjustable when setting
[CONNECTION] in the initial setting
to [VIDEO COMPONENT] or
[SCART S-VIDEO].
3
4
5
Press 5/∞ to adjust the parameter, then press ENTER.
Repeat step 2 and 3 to adjust other parameters.
Press VFP-I/P to finish the setting.
: At the beginning of a scene containing multi-
subtitles.
You can change the setting so that the on-screen
guide icons do not appear on the TV screen. (See
“ON SCREEN GUIDE” in “Initial settings.”)
•Receiver/decoder bearing neither Dolby Digital nor
DTS logo, or digital recorder, select “PCM ONLY.”
To play back without PBC
* 38 on the player starts/pauses playback.
•Opening the disc tray will set the function to off.
•This function is not available for some discs.
•If the disc cannot be played back, try to set the TRACK
ADJUST mode before you close the tray.
While stopped, press the numeric buttons instead of 3
(SELECT) to start playback.
Changing the display brightness
To bring up the DVD PLAYER SETUP display later
Press SET UP for a few seconds until the DVD PLAYER
SETUP display appears.
To reactivate PBC
Press DIMMER to change the brightness of the
display window.
•Press TOP MENU or MENU.
•Press 7 to stop playback, then 3 (SELECT).
5
6
7
8
XV-N330B/N332S[EK]2.indd
1
2/15/06 3:16:47 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|