JVC DVD Player XV N222S User Manual

CAUTION  
Notes on installation  
Connections  
Before making connections:  
• Do not connect the AC power cord until all other connections have been made.  
• Connect VIDEO OUT of the player directly to the video input of your TV. Connecting VIDEO OUT of the  
player to a TV via a VCR/an integrated TV/Video system may cause a monitor problem.  
Turning on the power  
Initial setup  
When you turn on the player for the first time after  
purchase, the following message appears on the TV  
screen.  
DVD PLAYER  
XV-N222S  
Warnings, Cautions and Others  
To reduce the risk of electrical shocks, fire, etc.:  
1. Do not remove screws, covers or cabinet.  
2. Do not expose this appliance to rain or moisture.  
• Select a place which is level, dry and neither too hot  
nor too cold between 5˚C and 35˚C (41˚F and 95˚F).  
• Leave sufficient distance between the player and the TV.  
• Do not install the player in a place subject to vibrations.  
• Do not put heavy objects on the player.  
To prevent malfunction of the player  
• There are no user-serviceable parts inside. If  
anything goes wrong, unplug the power cord and  
consult your dealer.  
• Do not insert any metallic objects, such as wires,  
hairpins, coins, etc. into the player.  
• Do not block the vents. Blocking the vents may  
damage the player.  
To clean the cabinet  
• Use a soft cloth. Follow the relevant instructions on  
the use of chemically-coated cloths.  
• Do not use benzene, thinner or other organic solvents  
and disinfectants. These may cause deformation or  
discoloring.  
CAUTION  
Inserting the AC power plug  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
After all other connections have been made, insert the  
AC power plug to the wall outlet firmly.  
Caution ––  
Disconnect the mains plug to shut the power off  
completely. The STANDBY/ON button in any  
position does not disconnect the mains line. The power  
can be remote controlled.  
STANDBY/ON button!  
EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO  
SETTING  
YES - PRESS ENTER NO - PRESS CANCEL  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK.  
DO NOT REMOVE COVER (OR BACK)  
INSTRUCTIONS  
V I D E O  
®
Basic Connection  
NO USER SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
Installing the batteries in the remote control  
Open the compartment cover, and place the two  
supplied R6(SUM-3)/AA(15F) batteries in the remote  
control according to the polarity markings (“+” and “–”)  
inside the compartment. Then replace the cover.  
S-video cable*  
(not supplied)  
TV  
NOTES  
Before enjoying this player, make the initial settings as  
follows:  
• If your TV has a monaural audio input  
instead of stereo, use an optional audio  
cable which converts stereo audio output to  
monaural.  
The lightning flash with arrowhead  
symbol, within an equilateral triangle is  
intended to alert the user to the presence  
of uninsulated “dangerous voltage” within  
the products enclosure that may be of  
sufficient magnitude to constitute a risk of  
electric shock to persons.  
The exclamation point within an equilateral  
triangle is intended to alert the user to the  
presence of important operating and  
maintenance (servicing) instructions in the  
literature accompanying the appliance.  
I
N
GNT0063-001A[US]  
0305MOC-MW-SC  
©2005 Victor Company of Japan, Limited  
CAUTION  
S-VIDEO  
EN  
THIS PRODUCT USES A LASER SYSTEM.  
USE OF CONTROLS OR ADJUSTMENTS OR  
PERFORMANCE OF PROCEDURES OTHER THAN THOSE  
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.  
REFER SERVICING TO QUALIFIED PERSONNEL.  
CLASS 1 LASER PRODUCT  
REPRODUCTION OF LABELS  
WARNING LABEL INSIDE OF THE UNIT  
1 Press ENTER.  
VIDEO  
DVD PLAYER SETUP  
Region code of DVD VIDEO  
• If your TV is a HDTV or HD-ready TV, you can  
connect with component (Y, PB, PR) jacks. By  
connecting with component (Y, PB, PR) jacks,  
you can select the progressive scanning  
mode which provides the best picture quality.  
* The S-VIDEO jack and component (Y, PB,  
PR) jacks cannot be used at the same time.  
When using the S-VIDEO jack, do not  
connect the component (Y, PB, PR) jacks  
with the player.  
L
E
F
T
MENU LANGUAGE  
AUDIO LANGUAGE  
SUBTITLE  
ENGLISH  
ENGLISH  
OFF  
This player can play back DVD VIDEO discs  
whose region code numbers include “1.”  
Examples of playable DVD VIDEO discs:  
AU  
DIO  
RI  
G
H
T
ON SCREEN LANGUAGE  
ENGLISH  
ENGLISH  
FRENCH  
SPANISH  
1 2  
3 4  
1 2 3  
4 5 6  
ALL  
1 5  
1
P
C
COA  
M
The player  
/
S
XIA  
TREAM  
L
2 Press 5/to select the on-screen language for  
The player’s region code is printed on the rear of  
the player  
Note of Color system format  
This player accommodates the NTSC system, and  
also can play back discs recorded with PAL  
system. (PAL video signals are converted to an  
NTSC signal and output.)  
PR  
the preference displays, etc., then press ENTER.  
Playable discs  
• DVD VIDEO, Audio CD, Video CD, SVCD  
DIGITA  
Yellow  
WARNING: TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
RI  
S-  
L
GH  
OUT  
VIDEO  
T
VID  
O  
DVD PLAYER SETUP  
VIDEO UT  
L
EF  
PB  
T
Audio/video  
cable*  
(supplied)  
MONITOR TYPE  
PICTURE SOURCE  
SCREEN SAVER  
BACKGROUND  
4:3 L.B.  
16:9  
AUDIO OUT  
AUTO  
4:3 LB  
For U.S.A.  
V I D E O  
4:3 PS  
ON  
CAUTION:  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to  
part 15 of the FCC Rules.  
STANDARD  
• DVD-R/-RW written in the DVD VIDEO format  
White  
• Do not block the ventilation openings or holes. (If the  
ventilation openings or holes are blocked by a newspaper  
or cloth, etc., the heat may not be able to get out.)  
• Do not place any naked flame sources, such as  
lighted candles, on the apparatus.  
• When discarding batteries, environmental problems  
must be considered and local rules or laws governing  
the disposal of these batteries must be followed strictly.  
• Do not expose this apparatus to rain, moisture, dripping  
or splashing and that no objects filled with liquids, such  
as vases, shall be placed on the apparatus.  
CD-R/RW written in the SVCD, Video CD or Audio CD format  
The batteries will last about six months with normal use.  
If the functions of the remote control become erratic,  
replace the batteries.  
Supplied accessories  
Red  
• CD-R/RW written in JPEG in accordance with the  
“ISO 9660” format  
These limits are designed to provide reasonable  
protection against harmful interference in a residential  
installation. This equipment generates, uses and can  
radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may  
cause harmful interference to radio communications.  
However, there is no guarantee that interference will  
not occur in a particular installation. If this equipment  
does cause harmful interference to radio or television  
reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to  
correct the interference by one or more of the  
following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver. Connect the equipment into an outlet on a  
circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV  
technician for help.  
If anything is missing, consult your dealer  
immediately.  
• Audio/video cable (Yellow/White/Red) (x 1)  
• Remote control (x 1)  
• R6(SUM-3)/AA(15F) battery (x 2)  
Connecting to a TV with component jacks  
Connecting to a stereo audio amplifier (receiver)  
3 Press 5/to select the monitor type, then press  
ENTER.  
P
B
Supported Digital audio formats:  
Linear PCM, Dolby Digital, DTS (Digital Theater Systems)*  
NOTES  
RIGHT  
Y
Precautions of the safe use of batteries  
Observe the following precautions for the safe use of  
batteries. If they are used improperly their lives will be  
shortened, they may burst or their contents may leak.  
• Remove the batteries from the remote control if it is  
not going to be used for a long period of time.  
• Remove dead batteries and dispose of them  
properly.  
• Never leave dead batteries lying around, take them  
apart, mix them with other refuse, or throw them into  
an incinerator.  
• Never touch liquid that has leaked out of a battery.  
• Do not mix new and old batteries, or batteries of  
different types, when placing them.  
• For a normal (conventional) TV, select “4:3 LB” or  
“4:3 PS.(See “MONITOR TYPE” in “Initial  
settings.”)  
LEFT  
PB  
EO  
VIDEO  
VIDEO OUT  
PR  
R
Y
COAXIAL  
AUDIO OUT  
/STREAM  
• If a disc gets dirty, scratched or warped, or due to the  
disc characteristics or recording conditions, the  
player may not be able to play back such discs.  
• The player can play back audio signals recorded in  
MIX-MODE CD, CD-G, CD-EXTRA and CD TEXT.  
• With some discs, operations may not be possible.  
* To play back DTS-encoded DVD VIDEO or DTS-  
encoded Audio CD discs correctly, connect the  
player to an amplifier with a built-in DTS decoder.  
Otherwise, playback sound will be distorted.  
LE
• Manufactured under license from Dolby  
Laboratories. “Dolby” and the double-D symbol are  
trademarks of Dolby Laboratories.  
• “DTS” and “DTS Digital Out” are trademarks of  
Digital Theater Systems, Inc.  
• This product incorporates copyright protection  
technology that is protected by U.S. patents and  
other intellectual property rights. Use of this  
copyright protection technology must be authorized  
by Macrovision, and is intended for home and other  
limited viewing uses only unless otherwise  
authorized by Macrovision. Reverse engineering or  
disassembly is prohibited.  
To analog audio input  
• For a wide-screen TV, select “16:9.”  
S-VIDEO  
VIDEO  
VIDEO OUT  
PR  
AUDIO OUT  
TAL OUT  
Connecting to a digital audio device  
To component video input  
DVD PLAYER SETUP  
To enjoy high-quality surround sound, connect the  
DIGITAL OUT (COAXIAL) jack to a Dolby Digital or DTS  
decoder or an amplifier with a built-in decoder.  
DIGITAL AUDIO OUTPUT  
DOLBY DIGITAL/PCM  
PCM ONLY  
Precautions  
To switch the scanning mode between Progressive and  
Interlace, press and hold VFP-I/P on the remote control  
for a few seconds.  
ANALOG DOWNMIX  
D.RANGE CONTROL  
OUTPUT LEVEL  
DOLBY PROLOGIC  
DOLBY DIGITAL/PCM  
Notes on the power cord  
STREAM/PCM  
ON  
• When you are away on travel or otherwise for an extended  
period of time, remove the plug from the wall outlet. A  
small amount of power (1.0 W) is always consumed while  
the power cord is connected to the wall outlet.  
• When unplugging the player from the wall outlet,  
always pull the plug, not the power cord.  
• Do not handle the power cord with wet hands!  
• Disconnect the power cord before cleaning the  
player or moving the player.  
• Do not alter, twist or pull the power cord, or put  
anything heavy on it, which may cause fire, electric  
shock, or other accidents.  
• If the cord is damaged, consult a dealer and have the  
power cord replaced with a new one.  
Avoid moisture, water, dust, and high temperatures  
• Do not place the player in moist or dusty places.  
• If water gets inside the player, turn off the power and remove  
the plug from the wall outlet, then consult your dealer. Using  
the player in this state may cause a fire or electrical shock.  
• Do not expose the player to direct sunlight or place it  
near a heating device.  
STANDARD  
PB  
RIGHT  
Y
COAXIAL  
PCM/STREAM  
NOTES  
LEFT  
• Connect “Y” to “Y,”“PB” to “PB(CB),”“PR” to “PR(CR)”  
correctly.  
S-EO  
VIDEO  
VIDEO OUT  
PR  
AUDIO OUT  
DIGITAL OUT  
Unplayable discs  
4 Press 5/to select a desired digital output  
signal type, then press ENTER.  
• When using component (Y, PB, PR) jacks, do not  
connect S-VIDEO jack with the player.  
To analog  
audio input  
If you try to play back discs listed below, noise may be  
generated and causes damage to speakers.  
• DVD-RW written in the VR format  
• DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM,  
PHOTO CD, SACD  
Set this item correctly according to the logo on your  
receiver or decoder.  
(If you do not connect the player to such a device,  
press ENTER to finish the setting.)  
• Receiver/decoder bearing Dolby Digital logo and  
no DTS, select “DOLBY DIGITAL/PCM.”  
• Receiver/decoder bearing both Dolby Digital and  
DTS logos, select “STREAM/PCM.”  
• Receiver/decoder bearing neither Dolby Digital nor  
DTS logo, or digital recorder, select “PCM ONLY.”  
Turning on and off the player  
About the scanning mode indicator  
[PICTURE SOURCE] of  
the PICTURE menu  
AUTO  
FILM  
VIDEO(NORMAL)/  
(ACTIVE)  
Source type of DVD VIDEO  
Press  
STANDBY/ON.  
For customer use  
Film source  
[DDP]  
[DDP]  
Video source  
[P]  
For Canada  
To digital audio input  
Enter below the Model No. and Serial No. which are  
located either on the rear, bottom or side of the cabinet.  
Retain this information for future reference.  
Model No.  
• Unfinalized discs  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH  
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT  
NOTES  
[DDP]  
• Discs of irregular shape or discs with tape, seals or  
paste on either the label side or playback side.  
Playing back these discs may damage the player.  
• Depending on the disc, no signal may be outputted  
from the DIGITAL OUT. Make an analog connection  
in this case.  
• Set [DIGITAL AUDIO OUTPUT] in the [AUDIO]  
preference display correctly according to the  
connected digital audio equipment. (See “DIGITAL  
AUDIO OUTPUT” in “Initial settings.”)  
[P]  
[P]  
Serial No.:  
For Canada  
NOTE  
THIS DIGITAL APPARATUS DOES NOT EXCEED THE  
CLASS B LIMITS FOR RADIO NOISE EMISSIONS  
FORM DIGITAL APPARATUS AS SET OUT IN THE  
INTERFERENCE-CAUSINGEQUIPMENTSTANDARD  
ENTITLED “DIGITAL APPARATUS,” ICES-003 OF  
THE DEPARTMENT OF COMMUNICATIONS.  
The Non-DVD side of a “DualDisc” does not comply with  
the “Compact Disc Digital Audio” standard.  
Therefore, the use of Non-DVD side of a DualDisc on  
this product may not be recommended.  
Some progressive TV and High-Definition TV sets are  
not fully compatible with the player. To check the  
compatibility of your TV, contact your local JVC  
customer service center.  
To bring up the DVD PLAYER SETUP display later  
Press SET UP for a few seconds until the DVD PLAYER  
SETUP display appears.  
1
2
3
4
Basic Operations  
Advanced Operations  
Menu bar functions  
You can use various functions from the menu bar.  
• OFF:  
Repeat mode deactivated. Select this to  
quit repeat mode.  
Turning on and off the player  
Open/close the disc tray  
Changing the display window  
contents  
Changing the language, sound  
Changing the picture tone (VFP)  
and scene angle  
Insert a disc  
1 Press 0 to open the disc tray.  
To bring up the menu bar  
The VFP (Video Fine Processor)  
function allows you to adjust the  
picture character according to the  
type of programming, picture tone or  
personal preferences.  
STANDBY/ON  
specifies beginning point of a title (DVD) or a  
OPEN/  
Each time you press DISPLAY,  
When a disc is inserted, press ON SCREEN twice.  
A menu bar for the type of disc inserted will appear  
under the status bar.  
CLOSE  
1 Press the button.  
STANDBY/ON  
OPEN/  
CLOSE  
disc (CD/VCD/SVCD) by the time.  
DVD:  
CD:  
the display window contents  
2 Press the button repeatedly or  
2 Place a disc in the disc tray.  
• To insert an 8-cm disc, place it in the inner  
recess.  
+
SLOW  
DISPLAY ON SCREEN  
In any condition  
In any condition except program or  
random playback  
changes.  
Turning on and off the player  
5/to select the desired item.  
3 Press ENTER to finish the  
setting.  
Basic playback  
+
SLOW  
DISPLAY ON SCREEN  
Ex.: Menu bar for DVD VIDEO  
TOP  
MENU  
THUMBNAIL/  
LIST  
Buttons To do  
TOP  
MENU  
THUMBNAIL/  
Locating the beginning of a scene  
1 Press VFP-I/P.  
LIST  
3 Press 0 to close the disc tray.  
VCD/SVCD: In any condition except PBC or program  
or random playback  
or song  
3* Start/resume normal Playback  
2 Press 2/3 to select the desired  
Buttons  
To do  
ENTER  
preset.  
You can select a title/chapter/  
track directly and start playback.  
For DVD Video:  
(While stopped) select title.  
(While playing back) select  
chapter.  
ENTER  
7
Stop  
AUDIO  
For DVD Video:  
select audio languages.  
For SVCD/VCD:  
select the audio  
channel.  
specifies a chapter to play back from  
(DVD only).  
• When RESUME is ON or DISC  
RESUME, this player memorizes  
the position on the disc where  
you interrupted playback.  
– To resume playback, press 3.  
– To stop playback completely,  
press 7 again.  
MENU  
SET UP  
NEXT  
Selected  
Preset  
To dismiss the menu bar and the status bar, press ON  
SCREEN.  
USER 1  
GAMMA  
MENU  
SET UP  
NEXT  
PREVIOUS SELECT  
MID  
PREVIOUS SELECT  
BRIGHTNESS  
CONTRAST  
SATURATION +10  
+
4
CLEAR  
selects the audio language (DVD), sound  
Basic operation procedure  
CLEAR  
+10  
track (DVD), or audio channel (VCD/SVCD) during  
playback.  
1
Press 2/3 to select the icon you want to work with.  
SUBTITLE select the subtitle.  
ANGLE select the view-angle.  
For SVCD/VCD/CD:  
Select track.  
1
4
2
5
8
0
3
6
2 Press ENTER.  
TINT  
+10  
1
4
2
5
8
0
3
6
After pressing ENTER:  
SHARPNESS  
Y DELAY  
LOW  
selects the subtitle language (DVD) or  
subtitle (SVCD) during playback.  
To select 5: press 5.  
8*  
Pause  
(1) When a pull-down menu appears, press 5/to  
select the setting you want, then press ENTER.  
(2) When a number-entry box appears, use the  
numeric buttons to enter the number you want,  
then press ENTER.  
+
2
To select 23: press 2, then 3.  
To select 40: press 4, then 0.  
• If you press TITLE/GROUP  
before entering the number, you  
can select the title instead of the  
chapter.  
• Each time you press  
8
on the  
7
9
CANCEL  
RETURN  
7
9
remote control, the still picture  
advances to the next frame.  
Parameter  
Changing the Sound Field  
CANCEL  
RETURN  
selects a desired scene angle in a multi-  
angle part (DVD only).  
NORMAL For watching TV in a  
TITLE/  
GROUP  
SOUND  
EFFECT  
Each time you press SOUND  
EFFECT, the Sound Effect mode  
changes.  
• As the value becomes bigger, the  
Sound Effect works stronger.  
VFP DIMMER  
I/P  
general room.  
¡/1 Fast forward/backward  
(While paused)  
TITLE/  
GROUP  
SOUND  
EFFECT  
VFP DIMMER  
I/P  
(3) When changing  
setting, press ENTER  
CINEMA For watching a movie  
software in a room with  
suppressed light.  
ANGLE SUBTITLE AUDIO ZOOM  
SLIDE EFFECT  
specifies the playback order of tracks while  
Slow-motion playback  
ANGLE SUBTITLE AUDIO ZOOM  
SLIDE EFFECT  
repeatedly to select the setting you want.  
stopped (unavailable for DVD). You can program up to  
99 tracks.  
• Each time you press the button,  
NOTES  
Using the disc menu  
the playback speed changes.  
• The selected item on the menu bar is shown in green.  
• The available functions differ depending on the  
player status. Refer to the explanation below to check  
when you can use a certain function.  
With the label side up  
USER1  
USER2  
You can adjust  
1. After selecting  
icon, press the numeric  
You can operate a disc—SVCD/  
VCD with Playback Control*  
(PBC)—using the disc menu  
shown on the TV screen.  
* A method of controlling disc play  
for SVCD/VCD by using the disc  
menu.  
¢/4 Skip chapter/track  
parameters that affect the  
picture character and  
store the settings as a user  
preset. See below.  
• If you press and hold the button  
during playback, playback is  
advanced/reversed at 5 times  
normal speed.  
buttons to specify tracks in the desired order.  
• To correct the program, press 5/to move  
the track to be corrected, then press CANCEL. The  
track is erased and the subsequent programmed  
tracks move up.  
Pressing 7 clears all the programmed tracks.  
2. Press 3(SELECT) to start program playback.  
• During program playback, you cannot edit the  
program contents.  
• To exit the program mode, press ON SCREEN after  
clearing the program.  
to  
Menu bar functions  
Zooming the picture  
To adjust the picture tone  
selects the time mode shown in the display  
Each time you press ZOOM, the  
magnification changes.  
Point toward the remote sensor directly as possible  
(the operating range is approx. 5 m.)  
VARI-PLAY (For DVD Video)  
1 Select “USER1” or “USER2.”  
2 Press 5/to select a parameter, then press ENTER.  
(variable The disc is played back at about  
playback) 1.2 or 1.5 times (FAST)/0.8 or 0.6  
times (SLOW) normal speed.  
The sound is not muted, and the  
subtitle does not go off (except for  
DTS).  
window and the status bar.  
• TOTAL:Elapsed time of current title (DVD) or a disc  
(CD/VCD/SVCD)  
• T.REM: Remaining time of current title (DVD) or a disc  
(CD/VCD/SVCD)  
(Except for DVD: while stopped, disc total  
time)  
• TIME: Elapsed time of current chapter (DVD) or  
track (CD/VCD/SVCD)  
7 For DVD  
• You can use 5//2/3 button to  
move the zoomed position.  
1 Press TOP MENU or MENU to show the disc menu.  
2 Press 5//2/3 to select a desired item, then press  
About On-screen guide icons  
GAMMA  
Adjust this if the neutral color is bright or dark.  
The brightness of dark and bright portion is  
maintained (LOW/MID/HIGH).  
To return to the normal playback,  
select the normal size by pressing  
ZOOM repeatedly.  
: Playback.  
ENTER or 3 (SELECT).  
• With some discs, you can also select items by entering the  
number using the numeric buttons.  
: Pause.  
BRIGHTNESS Adjust this if the picture is bright or dark on the  
(For SVCD/VCD)  
activates random playback while stopped  
(unavailable for DVD).  
whole (–16 (darkest) to +16 (brightest)).  
/
: Slow-motion playback with the current  
speed.  
Main display  
7 For SVCD/VCD  
The disc is played back at about 2  
times (FAST)/0.5 times (SLOW)  
normal speed.  
• Each indicator lights up when corresponding  
function/mode is activated, or corresponding  
information is on the main display.  
1 While stopped, press TOP MENU or 3 (SELECT) to  
CONTRAST  
Adjust this if the far and near position is unnatural  
(–12 to +12).  
• REM: Remaining time of current chapter (DVD) or  
track (CD/VCD/SVCD)  
After selecting  
icon, press ENTER.  
show the menu.  
/
: Fast forward/backward playback with the  
current speed.  
2 Press the numeric buttons to select a desired item.  
To select 5: press 5.  
(Only for DVD Video)  
The player starts random playback.  
(while stopped, current track total time)  
SATURATION Adjust this if the picture is whitish or blackish  
The playback position moves back  
10 seconds before the current  
position (only within the same title).  
(–16 (blackest) to +16 (whitest)).  
selects repeat mode.  
To select 23: press 2, then 3.  
To select 40: press 4, then 0.  
: At the beginning of a scene containing multi-  
angle views.  
DVD:  
CD:  
During playback  
In any condition  
TINT  
Adjust this if the appearance of flesh tone is  
unnatural (–16 to +16).  
• To move to the next or previous page of the current menu,  
press ¢ or 4.  
: At the beginning of a scene containing multi-  
audio sounds.  
*
38 on the player starts/pauses playback.  
VCD/SVCD: In any condition except PBC playback  
• CHAPTER: Current chapter repeat (DVD)  
SHARPNESS Adjust this if the picture is indistinct (LOW/HIGH).  
• To return to the previous menu, press RETURN.  
: At the beginning of a scene containing multi-  
subtitles.  
You can change the setting so that the on-screen  
guide icons do not appear on the TV screen. (See  
“ON SCREEN GUIDE” in “Initial settings.”)  
To play back without PBC  
• TITLE:  
• TRACK:  
• ALL:  
Current title repeat (DVD)  
Y DELAY  
Adjust this if the picture looks separately/  
overlapped (–2 to +2).  
While stopped, press the numeric buttons instead of 3  
Current track repeat (CD/VCD/SVCD)  
All track repeat (CD/VCD/SVCD)  
A-B repeat (During playback). After  
selecting A-B, press ENTER at the  
beginning point of repeat, then press  
ENTER again at the end point.  
(SELECT) to start playback.  
To reactivate PBC  
Changing the display brightness  
3 Press 5/to adjust the parameter, then press ENTER.  
4 Repeat step 2 and 3 to adjust other parameters.  
5 Press VFP-I/P to finish the setting.  
• A-B:  
Press DIMMER to change the brightness of  
the display window.  
• Press TOP MENU or MENU.  
• Press 7 to stop playback, then 3 (SELECT).  
5
6
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Intellinet Network Solutions Switch 530347 User Manual
Jenn Air Cooktop JRC120012A User Manual
JL Audio Car Speaker SB D MGACAB 10W6v2 User Manual
JVC DVD VCR Combo 2A73501A User Manual
JVC Headphones SU DH1 E User Manual
JVC Stereo System UX P4R User Manual
Kalorik Fondue Maker CHM 16314 User Manual
Kenmore Freezer 5966523403 User Manual
Kenwood Kitchen Utensil KN400 User Manual
Kodak Camcorder ZM2 User Manual