DVD DIGITAL THEATER SYSTEM
TH-C7
SP-THC7F, SP-THC7C and SP-THC5S
Consists of XV-THC7, SP-PWC7,
TH-C6
Consists of XV-THC6, SP-PWC6,
SP-THC6F, SP-THC6C and SP-THC6S
TH-C5
SP-THC5F, SP-THC5C and SP-THC5S
Consists of XV-THC5, SP-PWC5,
TH-C4/TH-C3
Consists of XV-THC4, SP-PWC4,
SP-THC4F, SP-THC4C and SP-THC4S
Consists of XV-THC3, SP-PWC3,
SP-THC3F, SP-THC3C and SP-THC3S
For Customer Use:
INSTRUCTIONS
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
GVT0150-001C
[J/C]
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings, Cautions and Others/Mises en garde, précautions et indications diverses
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2. CAUTION: Do not open the top cover. There are
no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation
when open and interlock failed or defeated.
Avoid direct exposure to beam.
2. ATTENTION: N’ouvrez pas le couvercle
supérieur. Il n’y a aucune pièce réparable par
l’utilisateur à l’intérieur de l’appareil; confiez
toute réparation à un personnel qualifié.
3. ATTENTION: Risque de radiations laser visible
et invisible quand l’appareil est ouvert et que le
système de verrouillage ne fonctionne pas ou a
été mis hors service. Évitez toute exposition
directe au rayon.
4. REPRODUCTION OF LABEL: CAUTION
LABEL, PLACED INSIDE THE UNIT.
4. REPRODUCTION DE L’ÉTIQUETTE:
ÉTIQUETTE DE PRÉCAUTION PLACÉE À
L’INTERIEUR DE L’APPAREIL.
ATTENTION
Afind’évitertoutrisqued’électrocution,d’incendie,etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas
ouvrir le coffret de l’appareil.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
CAUTION —
button!
ATTENTION — Touche
( XV-THC7/ XV-THC6/ XV-
( XV-THC7/ XV-THC6/ XV-
THC5/ XV-THC4/ XV-THC3)
Disconnect the mains plug to shut the power off
completely (the STANDBY lamp goes off).
THC5/ XV-THC4/ XV-THC3)
Déconnectez la fiche d’alimentation secteur pour
couper l’alimentation complètement (le témoin
STANDBY s’éteint).
The
button in any position does not disconnect
the mains line.
La touche
, dans n’importe quelle position, ne
• When the system is on standby, the STANDBY
lamp lights red.
• When the system is turned on, the STANDBY
lamp goes off.
déconnecte pas le système du secteur.
• Quand le système est en attente, le témoin
STANDBY est allumé en rouge.
• Quand le système est sous tension, le témoin
STANDBY s’éteint.
The power can be remote controlled.
L’alimentation ne peut pas être télécommandée.
CAUTION
ATTENTION
(SP-PWC7/SP-PWC6/SP-
(SP-PWC7/SP-PWC6/SP-
PWC5/SP-PWC4/SP-PWC3)
The power supply to the subwoofer is linked to the
center unit. The POWER ON lamp on the
PWC5/SP-PWC4/SP-PWC3)
L’alimentation au caisson d’extrêmes graves passe
par l’unité centrale. Le témoin POWER ON vert sur
le caisson d’extrêmes graves s’allume quand le
système est allumé.
subwoofer lights green when the power is turned on.
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Introduction .....................................2
Notes on handling .................................................................2
Supplied accessories ............................................................2
Playback ........................................20
Basic playback ....................................................................20
One Touch Replay ...............................................................22
Fast-forward/fast-reverse search ........................................22
Skip to the beginning of a desired selection .......................22
Locating a desired title/group using number buttons .........23
Playing back a bonus group ................................................23
Selecting the desired title/playlist from the control display .23
About discs .....................................3
Playable disc types ...............................................................3
Notes on file types ................................................................3
Description of parts and controls ...4
Advanced operations ....................24
Using the surround mode ...................................................24
Using the on-screen bar .....................................................25
Playing from a specified position on a disc .........................27
Using the file control display ..............................................28
Resume Playback ...............................................................29
Selecting a view angle .........................................................29
Selecting the subtitle ..........................................................29
Selecting the audio .............................................................30
Special picture playback .....................................................30
Program Playback ...............................................................32
Random Playback ...............................................................33
Repeat Playback .................................................................33
Tray lock .............................................................................34
Sound and other settings ....................................................35
Connections ....................................7
Connecting the FM and AM antennas ....................................7
Connecting the satellite (front, center, surround) speakers ..... 8
Speaker layout ....................................................................12
Connecting a TV ..................................................................12
Connecting the powered subwoofer ....................................13
Connecting to an analog component ...................................13
Connecting to a digital component .....................................13
Connecting the power cord .................................................13
Operating external components with
the remote control ........................14
Operating the TV .................................................................14
Operating the DBS tuner or CATV converter .......................14
Operating the VCR ..............................................................15
Setting DVD preferences ..............36
Using the setup menus .......................................................36
Menu description ................................................................36
Basic operations ...........................16
Turning the system on/off ...................................................16
Selecting the source to play ................................................17
Adjusting the volume [VOLUME] ........................................17
Listening with headphones (not supplied) ..........................17
Turning off the sound temporarily [MUTING] .....................17
Adjusting the brightness of the indications [DIMMER] .......17
Sleep Timer [SLEEP] ...........................................................18
Adjusting the output level of the subwoofer and speakers ..18
Adjusting the treble sound [TREBLE] ..................................18
Adjusting the bass sound [BASS] .......................................18
Changing the scan mode ....................................................18
Optimizing the speaker settings [Smart Surround Setup] ...19
Tuner operations ...........................39
Manual tuning .....................................................................39
Preset tuning ......................................................................40
Selecting the FM reception mode ........................................40
Reducing the noise of AM broadcast ..................................40
AV COMPU LINK remote control
system ...........................................41
References ....................................42
Maintenance .......................................................................42
Troubleshooting ..................................................................42
Specifications .....................................................................43
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
7 Safety precautions
Notes on handling
7 Important cautions
Avoid moisture, water and dust
Do not place the system in moist or dusty places.
Avoid high temperatures
Do not expose the system to direct sunlight and do not place it near
a heating device.
Installation of the system
• Select a place which is level, dry and neither too hot nor too cold;
between 5°C and 35°C.
When you are away
When away on travel or for other reasons for an extended period of
time, disconnect the power cord plugs from the wall outlet.
• Leave sufficient distance between the system and the TV.
• Do not use the system in a place subject to vibration.
Power cord
Do not block the vents
Blocking the vents may damage the system.
• Do not handle the power cord with wet hands!
• A small amount of power is always consumed while the power
cord is connected to the wall outlet (center unit only).
• When unplugging the power cord from the wall outlet, always
pull on the plug, not the power cord.
Care of the cabinet
When cleaning the system, use a soft cloth and follow the relevant
instructions on the use of chemically-coated cloths. Do not use
benzene, thinner or other organic solvents including disinfectants.
These may cause deformation or discoloring.
To prevent malfunctions of the system
• There are no user-serviceable parts inside. If anything goes
wrong, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the system.
• Do not use any non-standard shape disc (like a heart, flower or
credit card, etc.) available on the market, because it may damage
the system.
If water gets inside the system
Turn the system off and disconnect the power cord plug from the
wall outlet, then call the store where you made your purchase.
Using the system in this condition may cause fire or electrical
shock.
• Do not use a disc with tape, stickers, or paste on it, because it
may damage the system.
Label sticker
Supplied accessories
Check to be sure you have all of the supplied accessories.
The number in parentheses is the quantity of the pieces supplied.
If anything is missing, contact your dealer immediately.
Sticker
Paste
• Remote control (1)
• Batteries (2)
• FM antenna (1)
Note about copyright laws
• AM loop antenna (1)
• Power cord (1)
Check the copyright laws in your country before recording from the
discs. Recording of copyrighted material may infringe copyright
laws.
• System cord (1)
• Composite video cord (1)
Note about copyguard system
• Speaker cords (except for TH-C3)
For satellite (front left/right) and center speakers (3)
For satellite speakers (surround left/right) (2)
The discs are protected by copyguard system. When you connect
the system to your VCR directly, the copyguard system activates
and the picture may not be played back correctly.
• Screws
TH-C7 (for satellite speakers):
M4 x 35 mm (8)
TH-C6 (for satellite speakers):
M5 x 25 mm (4)
M4 x 55 mm (12)
TH-C5 (for satellite speakers):
M4 x 40 mm (6)
• Bottom covers (for TH-C6 only)
For satellite speakers (front and surround) (4)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
About discs
If a DVD with an improper Region Code number is loaded,
“REGION CODE ERROR!” appears on the TV screen and
playback cannot start.
Playable disc types
This system has been designed to play back the following discs:
Notes on DVD-R, DVD-RW and DVD-RAM
DVD VIDEO
DVD AUDIO
• This system can also play finalized DVD-Rs or DVD-RWs
recorded in DVD VIDEO format and DVD-RWs or DVD-RAMs
recorded in DVD VR format.
• This system can also play DVD-Rs or DVD-RWs if MP3, WMA,
and JPEG files are recorded on them with UDF Bridge format.
This system does not support “multi-border” discs.
VCD/SVCD
Audio CD
Notes on CD-R and CD-RW
• This system can also play CD-Rs or CD-RWs if MP3, WMA and
JPEG files are recorded on them with ISO 9660 format.
• This system supports “multi-session” discs (up to 20 sessions).
• This system cannot play “packet write” discs.
• DVD Logo is a trademark of DVD Format/Logo Licensing
Corporation.
• The Non-DVD side of a “DualDisc” does not comply with the
“Compact Disc Digital Audio” standard. Therefore, the use of
Non-DVD side of a DualDisc on this product may not be
recommended.
• This system accommodates the NTSC system, and also can play
discs recorded with PAL system. Note that the PAL video signal
on a disc is converted to an NTSC signal and output.
• On some DVD VIDEOs, DVD AUDIOs, VCDs or SVCDs, their
actual operation may be different from what is explained in this
manual. This is due to the disc programming and disc structure,
not a malfunction of this system.
Some discs may not be played back because of their disc
characteristics, recording conditions, or damage or stain on them.
Unplayable discs:
SACD, CD-I (CD-I Ready), Photo CD, etc.
Playing back these discs will generate noise and damage the
speakers.
Notes on file types
For all playable files
• The system can only recognize and play files with one of the
following extensions, which can be in any combination of upper
and lower case;
• Before playing back discs, read their instructions or cautions
carefully.
Region code of DVD VIDEO
MP3:
“.MP3”, “.mp3”
This system can play back DVD VIDEO discs whose Region Code
numbers include the system’s Region Code, which is indicated on
the rear panel.
WMA: “.WMA” , “.wma”
JPEG: “.JPG”, “.JPEG”, “.jpg”, “.jpeg”
• The system recognizes up to 150 tracks (files) per group, 99
groups per disc, and the total number of the tracks (files) that the
system can play is 4000.
Example of playable DVD:
• Some files may not be played back normally because of their disc
characteristics or recording conditions.
1 2
3 4
ALL
1 2
1
For MP3/WMA files
• The system supports MP3/WMA files recorded with a bit rate of
32 – 320 kbps and a sampling frequency of 16 kHz, 22.05 kHz,
24 kHz*, 32 kHz, 44.1 kHz, or 48 kHz.
• If the tag information (album name, artist, and track title, etc.) is
recorded on a disc, it appears in the file control display on the TV
screen. (A pg. 28)
• We recommend to record each piece of material (song) at a
sample rate of 44.1 kHz and at a data transfer rate of
128 (96*) kbps.
* For WMA only
For JPEG files
• We recommend to record a file at 640 x 480 resolution.
• This system can only play baseline JPEG files.
This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology
must be authorized by Macrovision, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of parts and controls
Front panel (center unit)
Display window
pg. 25
pg. 21
pg. 22
pg. 25
pg. 39 pg. 40
FM AM
P LPCM SURR
MHz
kHz
CH
WMAMP3
RESUME
PROGRESSIVE B.S.P. CHAP. TRK PG PL BONUS ST MONO
PRG RND
DISC ALL
pg. 33
pg. 32
pg. 33
pg. 21
pg. 39
pg. 40
pg. 21
pg. 29
pg. 31
pg. 21
pg. 21 pg. 23
pg. 18
pg. 22
pg. 20
pg. 22
pg. 17
pg. 20
/
/
TUNING
SOURCE
Disc tray (inside): pg. 20
pg. 17
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
pg. 16
pg. 20, 22
pg. 17
pg. 16
Remote sensor:
pg. 6
Rear panel (center unit)
pg. 7
pg. 13
pg. 13
pg. 13
pg. 12
pg. 13
pg. 12 pg. 13
pg. 41
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of parts and controls
Powered subwoofer
SP-PWC7/SP-PWC5
Note that the illustration below is for SP-PWC5.
pg. 13
pg. 11
3Ω
16Ω
POWER ON
lamp:
pg. 16
Power cord:
pg. 13
Front
Rear
SP-PWC6/SP-PWC4/SP-PWC3
pg. 13
pg. 11
CAUTION:
SΩPEAKERΩ IMPEDANCE
4
16
POWER ON lamp:
pg. 16
Power cord:
Front
Rear
pg. 13
NOTE
• For safety reasons, always ensure that there is sufficient space behind the powered subwoofer.
* Do not block the ventilation openings.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of parts and controls
Remote control
Putting batteries in the remote control
pg. 14
TV/VIDEO
F AUDIO
VCR/DBS
MUTING
DBS
pg. 16
pg. 14
TV
DISC 5
VCR
DISC 1
DISC 3
DVD
DISC 2
DISC 4
FM/AM
pg. 15
pg. 17
pg. 20
pg. 17
R6P (SUM-3)/AA (15F)
type dry-cell batteries
(supplied)
TV VOL
CHANNEL AUDIO VOL
pg. 17
AUDIO
TV
pg. 14 – 39
pg. 14
pg. 14
pg. 20,
VCR/DBS
TUNING
pg. 20
pg. 22, 39
TUNING
SLOW
MEMORY
FM MODE
SLOW
pg. 22, 30
pg. 20, 40
pg. 27
TOP MENU/PG
MENU/PL
40
pg. 27
If the range or effectiveness of the remote control decreases,
replace both batteries.
pg. 18,
36
ENTER
ON
CAUTION
• Do not expose batteries to heat or flame.
SCREEN
REC
pg. 15,
22
pg. 25
TITLE/GROUP
AUDIO
pg. 23
Operating the system from the remote
control
Aim the remote control directly to the front panel of the center unit.
• Do not hide the remote sensor.
pg. 30
pg. 29
Number
buttons:
pg. 22
SUBTITLE
ANGLE
PAGE
100+
TV RETURN
pg. 29
pg. 32
pg. 32, 33
pg. 18, 31
REPEAT PLAY MODE CANCEL
pg. 31
pg. 33
pg. 36
pg. 35
pg. 17
pg. 20
pg. 24
pg. 19
SET UP SETTING
ZOOM
SCAN MODE
VFP
pg. 31
pg. 18
FL DISPLAY DIMMER SLEEP
SMART
RETURN
TREBLE
pg. 27
pg. 18
S.SETUP BASS
SURROUND
FRONT L CENTER FRONT R
S.WFR
LEVEL
pg. 18
SURR. L
SURR. R
NOTE
• To use the buttons
under the cover, slide
down the cover.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Do not connect the power cord until all other connections have been made.
If reception is poor
Connecting the FM and
AM antennas
Center unit
AM loop antenna
7 AM loop antenna
Setting up supplied AM loop antenna
Outdoor single vinyl-covered wire antenna
(not supplied)
If the antenna cord is covered with the insulation
coat, twist and pull the insulation coat off and
remove.
7 FM antenna
FM antenna (supplied)
Center unit
Extend the supplied FM antenna
horizontally.
Connecting AM loop antenna
1
Center unit
If reception is poor
Center unit
Outdoor FM antenna
(not supplied)
2
Standard type (75 C
coaxial) connector
Outdoor FM antenna cord
(not supplied)
Antenna cord
NOTE
• We recommend that you use coaxial cable for the FM antenna as it is
3
well-shielded against interference.
• Turn the loop antenna until you have the best reception during
AM broadcast program reception.
NOTE
• Make sure the antenna conductors do not touch any other terminals,
connecting cords and power cords. This could cause poor reception.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not connect the power cord until all other connections have been made.
Connections
7 The front speakers — TH-C5
For the surround speakers of TH-C5, see “The surround speakers
— Except for TH-C6” (A pg. 10)
Connecting the satellite
(front, center, surround)
speakers
7 The front speakers — TH-C7
For the surround speakers of TH-C7, see “The surround speakers
— Except for TH-C6” (A pg. 10)
Front speaker
(x2)
Base plate
(x2)
Before assembling —
• Prepare a Phillips screwdriver (not supplied).
• Take care not to drop any component part while assembling;
otherwise, it may cause damage to the floor or injury.
Front speaker
(x2)
Base plate
(x2)
1
Before assembling —
• Prepare a Phillips screwdriver (not supplied).
Base plate
• Take care not to drop any component part while assembling;
otherwise, it may cause damage to the floor or injury.
1
Top of base plate
Speaker (rear side)
FRONT
Screw M4 x 40 mm
(supplied)
Screw M4 x 35 mm
(supplied)
Speaker (bottom)
Base plate
CAUTION
• NEVER insert your finger in between the speaker and the base plate,
CAUTION
• NEVER insert your finger in between the speaker and the base plate,
as it may get hurt.
as it may get hurt.
2
2
White
Red
White
Red
Black
Black
Black
Black
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not connect the power cord until all other connections have been made.
Connections
7 The front and surround speakers — TH-C6
The following procedure explains the front speaker assembly. The
assembly of both the front and surround speakers are done in the
same manner.
3
Speaker
Stand
Front speaker
Surround speaker
Stand
(×4)
4
(×2)
(×2)
Red
White
Base plate
(×4)
Black
Black
Before assembling —
• Prepare a Phillips screwdriver (not supplied).
• Take care not to drop any component part while assembling;
otherwise, it may cause damage to the floor or injury.
White
Black
Speaker
1
Screw M5 x 25 mm
(supplied)
Stand
When installing the front and surround speakers on the
wall;
• Attach the supplied bottom cover on the bottom of each speakers
as illustrated.
Stand
Base plate
2
Bottom
cover
• Be sure to have them installed on the wall by a qualified
personnel.
• DO NOT install the satellite speakers on the wall by yourself to
avoid unexpected damage from their falling off the wall due to
incorrect installation or weakness in wall structure.
• Care must be taken in selecting a location for speaker installation
on a wall. Injury to personnel or damage to equipment may result
if the speakers installed interfere with daily activities.
• If attaching the stand to the speaker, remove the bottom cover by
inserting a flat-pointed tool into the hole of the bottom cover.
Screw M4 x 55 mm
(supplied)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not connect the power cord until all other connections have been made.
Connections
7 The front speakers — TH-C4
7 The center speaker
The following procedure explains SP-THC5C assembly. The
assembly of other center speakers is done in the same manner.
Front speaker
Center speaker
(×2)
(×1)
White
Red
Black
Black
White
Red
Black
Black
White
For TH-C3, the front, surround and center speakers are equipped
with their speaker cords attached directly to their speaker unit
instead of having speaker terminals on their cabinet.
Black
7 The surround speakers — Except for TH-C6
Surround speaker
Front speaker
Surround speaker
Center speaker
(×2)
1
Speaker
(bottom)
2
White
Red
Black
Black
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not connect the power cord until all other connections have been made.
Connections
Note that the illustration below is for SP-PWC6.
Before connecting the speaker cords;
Twist and pull the insulation coat off and remove.
Powered subwoofer
TH-C7: SP-PWC7
TH-C6: SP-PWC6
TH-C5: SP-PWC5
TH-C4: SP-PWC4
TH-C3: SP-PWC3
Speaker cord
• Connect the black cords to the black (r) terminals.
• Connect the white cords to the (q) terminals
referring to the table below:
Front speakers
TH-C7: SP-THC7F
TH-C6: SP-THC6F
TH-C5: SP-THC5F
TH-C4: SP-THC4F
TH-C3: SP-THC3F
FRONT SPEAKERS (LEFT)
FRONT SPEAKERS (RIGHT)
CENTER SPEAKER
White
Red
Green
Blue
SURROUND SPEAKERS (LEFT)
SURROUND SPEAKERS (RIGHT)
Gray
CAUTION:
SΩPEAKERΩ IMPEDANCE
4
16
Surround speakers
TH-C7, TH-C5: SP-THC5S
Center speaker
TH-C6:
TH-C4:
TH-C3:
SP-THC6S
TH-C7: SP-THC7C
TH-C6: SP-THC6C
TH-C5: SP-THC5C
TH-C4: SP-THC4C
TH-C3: SP-THC3C
SP-THC4S
SP-THC3S
Precautions for daily use
CAUTION
• When moving the speakers, do not pull the speaker cords;
otherwise, the speakers may fall over, causing damage or injury.
• Do not reproduce sounds at so high a volume that they are
distorted; otherwise, the speakers may be damaged by internal
heat buildup.
• When you connect speakers other than the supplied ones, use
speakers of the same speaker impedance (SPEAKER IMPEDANCE)
indicated near the speaker terminals on the rear of the powered
subwoofer.
• DO NOT connect more than one speaker to one speaker terminal.
(For TH-C7, TH-C6 and TH-C5)
• When holding a speaker, always grasp the lower portion.
• Do not lean against the speakers, as the speakers could fall down
or break, possibly causing an injury. Especially be careful that
children do not lean against them.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not connect the power cord until all other connections have been made.
Connections
Speaker layout
Connecting a TV
• You can get better picture quality in the order — Component
video > S-video > Composite video.
• Distortion of picture may occur when connecting to the TV via a
VCR, or to a TV with a built-in VCR.
Center speaker
Front left
speaker
Front right
speaker
• You need to set “MONITOR TYPE” in the PICTURE menu
correctly according to the aspect ratio of your TV. (A pg. 37)
Powered
subwoofer
7 To connect a TV equipped with the component video
input jacks
Center unit
TV
To component
video input
Surround left
speaker
Surround right
speaker
Component video cord (not supplied)
• Place the satellite speakers on a flat and level surface.
• The front and center speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly, they may
cause color distortions. So, pay attention to the following when
installing the speakers.
NOTE
• If your TV supports progressive video input, you can enjoy a high
quality picture by setting the progressive scan mode to active.
(A pg. 18)
• If the component video input jacks of your TV are of the BNC type,
use a plug adapter (not supplied) to convert the pin plugs to BNC
plugs.
– When placing the speakers near a TV set, turn off the TV’s main
power switch or unplug it before installing the speakers. Then wait
at least 30 minutes before turning on the TV’s main power switch
again.
Some TVs may still be affected even though you have followed the
above. If this happens, move the speakers away from the TV.
• The surround speakers are not magnetically shielded.
If it is located nearby the TV or monitor, it will probably cause
color distortion on the screen. To avoid this, do not place the
speaker nearby the TV or monitor.
• The component video signals can be output only when you select
“DVD” as the source to play. (A pg. 17)
7 To connect a TV equipped with the composite or S-
video jacks
• Be sure to place the powered subwoofer to the TV’s right. If you place
the powered subwoofer to the TV’s left, keep sufficient distance
between them to prevent the TV screen from appearing mottled.
Center unit
Composite video cord
(supplied)
or
S-video cord
(not supplied)
Align the 5 marks.
To S-video input
To composite
video input
TV
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not connect the power cord until all other connections have been made.
Connections
Connecting the powered
subwoofer
Connecting to a digital
component
You can enjoy the sound of a digital component.
Powered
subwoofer
Center unit
Center unit
System cord
(supplied)
Align the 5 marks.
or
To digital optical output
DBS* tuner
MD player
Align the 5 marks.
Digital optical cord (not supplied)
NOTE
• The way of connecting the system cord varies depending on the type
of the powered subwoofer.
* DBS = Direct Broadcasting Satellite
NOTE
• Only digital audio signals can be input when selecting “DBS” as the
source to play. (A pg. 17) When connecting a video component such
as a DBS tuner, operate this system to listen to the sound.
Connecting to an analog
component
You can enjoy the sound of an analog component.
Connecting the power
cord
Make sure that all other connections have been completed.
Center unit
Center unit
Powered
subwoofer
S-video cord
(not supplied)
RCA pin plug
cord
or
(not supplied)
Composite video
cord
(not supplied)
Power cord
(Supplied)
Power cord
1
2
C
VCR (1 3 or 2 3)
TV (C)
Cassette recorder (C)
Plug into AC outlets.
CAUTION
A To composite video output
B To S-video output
C To audio output
• Disconnect the power cord before cleaning or moving the system.
• Do not pull on the power cord to unplug the cord. When unplugging
the cord, always grasp and pull the plug so as not to damage the cord.
NOTE
• The signals input to the VIDEO jack of the VCR IN jacks will be
output only from the VIDEO jack of the VIDEO OUT jacks, not from
the S-VIDEO jack of the VIDEO OUT jacks.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating external components with the remote control
4 Press number buttons (1-9, 0) to enter
The buttons described below are used on pages 14 and
15.
the manufacturer’s code (2 digits).
Examples:
For a Hitachi TV:
Press 1, then 0.
For a Toshiba TV:
Press 0, then 8.
TV/VIDEO
TV
VCR/DBS
Manufacturer
JVC
Code Manufacturer
Code
12
01
10
02
03
Samsung
Sharp
VCR
DBS
Hitachi
06
Magnavox
Mitsubishi
Panasonic
RCA
Sony
07
TV VOL
CHANNEL
Toshiba
08
Remote control
mode selector
TV
VCR/DBS
04, 11 Zenith
05
09
(play button)
5 Release TV.
If there is more than one code listed for corresponding brand,
try each one until you enter the correct one.
ENTER
7 Operation
Aim the remote control at the TV.
REC
IMPORTANT
Before using the remote control to operate a TV;
• Set the remote control mode selector to TV.
Number
buttons
The following buttons are available:
100+
TV RETURN
TV:
TV VOL +/–:
TV/VIDEO:
Turns TV on and off.
Adjusts the volume.
Selects the input mode (either TV or
VIDEO).
CHANNEL +/–:
Changes the channels.
1-10, 0, +10 (100+): Selects the channel.
TV RETURN: Alternates between the previously selected
channel and the current channel.
NOTE
• Manufacturers’ codes are subject to change without notice.
• Set the codes again after replacing the batteries of the remote control.
Operating the DBS tuner
or CATV converter
Operating the TV
7 To set the manufacturer’s code
You can operate a JVC TV without setting the manufacturer’s code.
7 To set the manufacturer’s code
1 Slide the remote control mode selector
1 Slide the remote control mode selector
to VCR/DBS.
to TV.
2 Press DBS.
2 Press and hold
TV.
Keep the button pressed until step 4 is finished.
3 Press and hold F VCR/DBS.
Keep the button pressed until step 5 is finished.
3 Press ENTER.
4 Press ENTER.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 14 for button locations.
Operating external components with the remote control
5 Press number buttons (1-9, 0) to enter
5 Press number buttons (1-9, 0) to enter
the manufacturer’s code (2 digits).
the manufacturer’s code (2 digits).
Examples:
For a GI Jerrold product:
Examples:
For a Philips VCR:
Press 0, then 1.
For a Sony product:
Press 2, then 0.
Press 0, then 9.
For an NEC VCR:
Press 2, then 5.
Manufacturer
Echostar
GI Jerrold
Hamlin
Code
Manufacturer Code
Manufacturer Code
21
JVC
01, 02, 03
Philips
RCA
09
01, 02, 03, 04, 05, 06, 07, 08
Emerson
Fisher
11, 26
29
05, 06
24
15, 16, 17, 18
13, 14
19
Samsung
Pioneer
Funai
10, 14, 15, 16 Sanyo
21, 22, 23
27, 28
30
RCA
Gold Star
Hitachi
Mitsubishi
NEC
12
Sharp
Scientific Atlanta
Sony
09, 10
20
04
Shintom
Sony
13
18, 19, 20
08
Zenith
11, 12
25
Zenith
Panasonic
07, 17
6 Release F VCR/DBS.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
6 Release F VCR/DBS.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
7 Operation
Aim the remote control at the DBS tuner or CATV converter.
7 Operation
Aim the remote control at the VCR.
IMPORTANT
Before using the remote control to operate a
DBS tuner or CATV converter;
1 Set the remote control mode selector to
VCR/DBS.
IMPORTANT
Before using the remote control to operate a
VCR;
1 Set the remote control mode selector to
2 Press DBS.
VCR/DBS.
2 Press VCR.
The following buttons are available:
F VCR/DBS:
Turns DBS tuner or CATV converter on and
off.
Changes the channels.
The following buttons are available:
F VCR/DBS: Turns VCR on and off.
3 (play button): Starts playback.
CHANNEL +/–:
1-10, 0, +10 (100+): Selects the channel.
7 :
8 :
Stops operation.
Pauses playback.
y :
1:
REC:
Fast forwards video tape.
Rewinds video tape.
Operating the VCR
Press this button together with 3 (play button) to
start recording or together with 8 to pause
recording.
7 To set the manufacturer’s code
CHANNEL +/–: Changes the TV channels on the VCR.
1 Slide the remote control mode selector
NOTE
When operating a VCR or DBS tuner/CATV converter;
to VCR/DBS.
• The source setting of VCR or DBS remains after you have changed
the remote control mode selector to AUDIO or TV. When operating
VCR or DBS tuner/CATV converter again, it is not necessary to press
VCR or DBS after setting the remote control mode selector.
2 Press VCR.
3 Press and hold F VCR/DBS.
Keep the button pressed until step 5 is finished.
4 Press ENTER.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations
The buttons on the remote control are used to explain most of the
operations in this manual. You can use the buttons on the center
unit same as on the remote control for operations unless
otherwise noted.
Turning the system on/off
On the remote control:
Press
AUDIO.
IMPORTANT
Before using the remote control for the following
On the center unit:
Press
.
operation;
• Set the remote control mode selector to AUDIO.
When DVD is selected as the source (A pg. 17), the following
messages will appear on the TV screen.
The buttons described below are used on
pages 16 to 19.
• “OPEN”/“CLOSE”:
Appears when opening or closing the disc tray.
• “NOW READING”:
Source
selecting
buttons
Appears when the system is reading the disc information.
• “REGION CODE ERROR!”:
Remote control
mode selector
Appears when the Region Code of the DVD VIDEO does not
match the code the system supports. The disc cannot be
played back.
• “NO DISC”:
Appears when no disc is loaded.
• “CANNOT PLAY THIS DISC”:
Appears when unplayable disc is loaded.
Cursor
(3/2/Y/5)/
ENTER
NOTE
• The STANDBY lamp turns on when the power is turned off and turns
off when the power is turned on.
• The power supply to the subwoofer is linked to the center unit. The
POWER ON lamp on the subwoofer lights green when the power is
turned on.
• A small amount of the power is consumed even when the power is
turned off (center unit only). This is called standby mode and the
STANDBY lamp lights in this mode. Unplug the power cord from the
AC outlet to turn the power off completely.
• You can also turn on the system by pressing the following buttons;
DIMMER SLEEP
SMART
•
•
•
One of 0 buttons on the center unit
One of the source selecting buttons on the remote control
One of the DISC (1-5) 3 buttons or 3 on the center unit
You can use the same buttons on the remote control.
S.SETUP BASS
TREBLE
LEVEL
BASS/
LEVEL
FRONT L CENTER FRONT R
Speaker
buttons
S.WFR
SURR. L
SURR. R
SOURCE
DISC
1
DISC
2
DISC
3
DISC
4
DISC
5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 16 for button locations.
Basic operations
Selecting the source to
play
Listening with headphones
(not supplied)
On the remote control:
CAUTION
Be sure to turn down the volume;
Press one of the source selecting buttons
(DVD, FM/AM, VCR or DBS).
DVD: To play back a disc (DVD VIDEO, VCD etc.). (A pg. 20)
FM/AM: To tune in an FM or AM station. (A pg. 39)
Each time you press the button, the band alternates
between FM and AM.
• Before connecting or putting on headphones as high volume may
damage both the headphones and your hearing.
• Before disconnecting headphones as high volume may be suddenly
output from the speakers.
While connecting a pair of headphones to the PHONES jack on the
center unit, the system automatically cancels the surround mode
(A pg. 24) currently selected, deactivates the speakers, turns the
subwoofer’s power off, and activates the headphone mode. “H.
PHONE” appears on the display window.
VCR: To select the source from a component connected to the
VCR IN jacks and AUDIO IN (VCR) jacks. (A pg. 13)
DBS: To select the source from a component connected to the
DIGITAL IN (DBS) jack. (A pg. 13)
Headphone mode
When using the headphones, the following signals are output
regardless of your speaker setting;
On the center unit:
Press SOURCE repeatedly until the source
name you want appears on the display
window.
• For 2 channel sources, the front left and right channel signals are
output from the headphones.
• Multi-channel signals are down-mixed and output from the
headphones.
NOTE
• When AM, FM or DBS is selected, this system does not output video
• (For DVD AUDIO) When the disc prohibits down-mixing, only
the front left and right channels are output from the headphones.
In this case, “LR ONLY” appears on the display window for a
few seconds.
signals.
• It may take time to change the source.
Adjusting the volume
[VOLUME]
Turning off the sound
temporarily [MUTING]
Press MUTING.
CAUTION
• Always set the volume to minimum level before starting any source.
If the volume is set at its high level, the sudden blast of sound could
permanently damage your hearing and/or blow out the speakers.
To restore the sound
Perform one on the following:
• Press MUTING again.
• Press AUDIO VOL +/– (or turn VOLUME on the center unit).
On the remote control:
Press AUDIO VOL +/–.
On the center unit:
Adjusting the brightness
of the indications
[DIMMER]
Turn VOLUME.
Press DIMMER.
Each time you press the button, the brightness level changes.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 16 for button locations.
Basic operations
Sleep Timer [SLEEP]
The system turns off automatically when the specified period of
time has passed.
Changing the scan mode
The system can be accommodated to your TV’s scan mode.
NOTE
Press SLEEP.
Each time you press the button, the shut-off time changes.
• To use the system in PROGRESSIVE mode, it is required that the
center unit is connected to the TV by using a component video cord
(not supplied). (A pg. 12)
Example:
7 While DVD is selected as the source and stopped
minutes
1 Press and hold SCAN MODE for
S L E E P
6 0
2 seconds.
“INT-LACE” or “PROGRESS” appears on the display
window.
To check the remaining time
Press SLEEP once.
2 Press Cursor 3/2 to select the desired
mode.
• INT-LACE:
To change the remaining time
Press SLEEP repeatedly.
Select this when your TV supports the
interlaced video input only.
To cancel
Press SLEEP repeatedly until “SLEEP – –” appears.
• Turning off the power also cancels the Sleep Timer.
• PROGRESS:
Select this when your TV equipped with
component jacks supports the progressive
video input.
You can get better picture quality in PROGRESSIVE mode
than in INTERLACE mode.
Adjusting the output level
of the subwoofer and
speakers
3 Press ENTER while the selected mode
is displayed.
When “PROGRESS” is selected, the PROGRESSIVE
indicator lights on the display window.
Press each speaker button you want to
adjust the output level and then LEVEL +/–.
NOTE
• Although the picture may be distorted when you press ENTER, this
is not a malfunction of the system.
• FRONT L:
• FRONT R:
• SURR. L:
• SURR. R:
• CENTER:
• S.WFR:
Front Left speaker
Front Right speaker
Surround Left speaker
Surround Right speaker
Center speaker
• There are some progressive TVs and High-Definition TVs that are
not fully compatible with this system, resulting in an unnatural
picture when playing back a DVD VIDEO in the progressive scan
mode. In such a case, change the scan mode to “INT-LACE”.
To check the compatibility of your TV, contact your local JVC
customer service center.
Subwoofer
NOTE
• You can also make adjustments by using the setup menu shown on the
• All JVC progressive TVs and High-Definition TVs are fully
compatible with this system.
TV screen. (A pg. 37)
• The adjustments take effect for all sources.
Adjusting the treble
sound [TREBLE]
Press TREBLE and then LEVEL +/–.
NOTE
• The adjustments take effect for all sources.
Adjusting the bass sound
[BASS]
Press BASS and then LEVEL +/–.
NOTE
• The adjustments take effect for all sources.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 16 for button locations.
Basic operations
When “FAILED !” appears on the TV screen
The system could not detect the clapping sound correctly. In such a
case, follow the instructions that appear on the TV screen.
• When the system detects the clapping sound as “FAILED !” three
times, set the delay time (DELAY) and the output level (LEVEL)
manually. (A pg. 37)
Optimizing the speaker
settings [Smart Surround
Setup]
NOTE
To cancel
• When you change the positioning of the speakers or listener, or
replace the supplied speakers with other ones, perform Smart
Surround Setup again.
Press SMART S. SETUP.
NOTE
• You need to set the subwoofer’s output level (LEVEL) manually.
7 While DVD is selected as the source and stopped
(A pg. 18)
• In step 2, “SW ERROR” appears on the display window if the center
unit and the powered subwoofer are not connected correctly by using
the supplied system cord.
1 Take your position where you listen to
the sound.
2 Press and hold SMART S. SETUP.
“SETTING” appears on the display window.
3 Clap your hands over your head once.
4 Make sure that “COMPLETED !”
appears on the TV screen, then press
SMART S. SETUP.
The system detects your clapping sound through the satellite
speakers, then automatically makes the best settings for each
speaker. “COMPLETED !” appears on the TV screen when
Smart Surround Setup completes.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
DVD
VIDEO
• The icon such as
shows the disc formats or file types the
Basic playback
operation is available for.
IMPORTANT
Before using the remote control for the
following operation;
1 Set the remote control mode selector to
AUDIO.
DVD DVD DVD
VIDEO AUDIO VR
1 Press the desired DISC (1-5)
0 on the center unit.
• The system turns on and the disc tray
comes out.
2 Press DVD.
2 Place a disc.
Label side up
The buttons described below are used on pages 20 to 23.
When placing an 8 cm
disc
2
2
C
C
IS
IS
D
D
1
1
I
SC
C
IS
D
D
DISC 1
DISC 3
DVD
DISC 2
DISC 4
DISC 5
3 Press DISC (1-5).
For MP3/WMA files
AUDIO
(play button)
Remote control
mode selector
The file control display (A pg. 28) appears on the TV screen.
For JPEG files
Each file (still pictures) is shown on the TV screen for about 3
seconds (slide-show). When stopping playback, the file control
TOP MENU/PG
MENU/PL
display (A pg. 28) appears on the TV screen.
TOP MENU/PG
MENU/PL
For DVD VR disc
Pressing TOP MENU/PG or MENU/PL shows the control display
on the TV screen. (A pg. 23)
ENTER
7 To pause playback
Press 8.
To return to playback, press 3 (play button).
TITLE/GROUP
Number buttons
7 To stop
Press 7.
7 On-screen guide icons
During DVD VIDEO playback, the following guide icons may
appear for a while on the TV screen;
FL DISPLAY
•
•
•
•
: appears at the beginning of a scene containing multi-
subtitle languages.
: appears at the beginning of a scene containing multi-audio
languages.
: appears at the beginning of a scene containing multi-angle
views.
(Play),
(Pause),
/
(Fast forward/
fast-reverse),
reverse): appears when you perform each operation.
/
(Slow-motion forward/
•
: the disc cannot accept an operation you have tried to do.
DISC
1
DISC
2
DISC
3
DISC
4
DISC
5
20
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 20 for button locations.
Playback
MP3/WMA file
NOTE
• Up to 5 discs can be loaded.
Example:
When an MP3 is played back
• You can also start playback by pressing 3 (play button) or DVD.
• The system plays back available discs sequentially until you stop
playback or until the disc loaded on the DISC 5 tray reaches to the
end. However, when DVD VIDEO or DVD AUDIO is loaded in the
system, playback of the disc next to the DVD VIDEO or DVD
AUDIO will not start.
Signal and speaker
indicators
Track number
:
1 2 3
1 2 3 4
MP3
• (For JPEG) The system cannot accept operations even though you
press any buttons before the entire picture appears on the TV screen.
• If you do not want the on-screen guide icons to appear, see page 38.
MP3 indicator*1
Elapsed playing time (minute:second)
(during playback only)
7 Playback information on the display window
DVD VIDEO
Pressing FL DISPLAY
Group number
Example:
When a DVD VIDEO encoded with Dolby Digital 5.1ch is played
2
G 1 2
T 1
3
Elapsed playing time
(hour:minute:second)
MP3
Chapter number
Track number
SURR
1: 2 3: 3 1
2 4
*1 WMA indicator lights for WMA disc.
Signal and speaker indicators (A pg. 25)
JPEG file
Surround mode and digital signal format (A pg. 25)
File number
1 2 3
J P E
G
Pressing FL DISPLAY
Title number
Chapter number
Pressing FL DISPLAY
T
C 2 4
1 5
SURR
Group number
File number
DVD AUDIO
G 1 2
F 1 2 3
Signal and speaker indicators
DVD VR disc
Example:
During playback on the Original program*
:
:
5
2
1 2 3
P LPCM
1
4
Track number
Elapsed playing time
(hour:minute:second)
Elapsed playing time
(hour:minute:second)
Title number
2 2
0: 2 0: 3 6
Pressing FL DISPLAY
PG
Group number
Track number
PG (Original program) indicator
2
P LPCM
3
T 1
G
Pressing FL DISPLAY
Title number
Chapter number
VCD/SVCD/CD
Example:
P G
1 C
3
When a CD is played back
PG
Signal and speaker
indicators
Track number
LPCM
1 2
3: 3
1
Elapsed playing time (minute:second)
NOTE
• When a VCD or SVCD with PBC function is played, the elapsed
playing time does not appear, but “PBC” appears.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 20 for button locations.
Playback
Example:
During playback on the Playlist*
Fast-forward/fast-reverse
search
7 During playback
Elapsed playing time
(hour:minute:second)
Title number
DVD DVD DVD
VIDEO AUDIO VR
3 0
0: 5 0: 3 0
PL
On the remote control:
Press y or 1.
Each time you press the button, the search speed
PL (Playlist) indicator
Pressing FL DISPLAY
changes.
To return to normal speed playback
Playlist number
Chapter number
Press 3 (play button).
Press and hold x or 4.
Continuously pressing x or 4 increases the fast-forward/
reverse search speed.
P L
1 C
1
PL
* Pressing TOP MENU/PG or MENU/PL, you can change the
play mode. (A pg. 23)
NOTE
• The operation with x or 4 above is available for a disc other
than MP3 and WMA.
NOTE
• You can change the time information mode (except for MP3/WMA/
• When a DVD VIDEO, DVD VR, VCD and SVCD is played back, no
sound comes out during fast-forward/reverse search.
• When a DVD AUDIO or CD is played back, sound is intermittent and
low during fast-forward/reverse search.
JPEG). (A pg. 26)
• You can also check the playback information on the TV screen.
(A pg. 25)
• This feature may not work for some discs.
7 Disc information on the display window
The disc indicators on the display window show the current status
of the corresponding disc tray.
Skip to the beginning of a
desired selection
Example:
When the discs are loaded to disc trays 1, 2 and 5, and the disc in the
disc tray 5 is selected.
DVD DVD DVD
VIDEO AUDIO VR
7 Using x/4 buttons
7 For DVD VIDEO/DVD VR (chapter):
During playback
For VCD/SVCD (track):
Currently selected
disc number
During playback without PBC function
For DVD AUDIO/CD/MP3/WMA/JPEG (track/file): During
playback or while stopped
Currently loaded disc number
Press x or 4 repeatedly.
NOTE
• When playing back an MP3/JPEG file, you can make operations
7 Screen saver
A TV screen may burn out if a static picture is displayed for a long
time. To prevent this, the system automatically dims the screen if a
static picture is displayed for over 5 minutes (the screen saver
function).
using the file control display. (A pg. 28)
• This feature may not work for some discs.
7 Using number buttons on the remote control
• Pressing any button will cancel the screen saver function.
• If you do not want to use the screen saver function, see page 37.
7 For DVD VIDEO/DVD VR (title, chapter):
While stopped, the title number is selected.
During playback, the chapter number is selected.
For DVD AUDIO (track):
During playback or while stopped
For VCD/SVCD (track):
During playback without PBC function
For CD/MP3/WMA/JPEG (track/file):
During playback or while stopped
One Touch Replay
You can move back the playback position by 10 seconds
from the current position.
7 During playback
DVD DVD
VIDEO VR
Press number buttons (0-10, +10) to select
the desired number.
• For details on using the number buttons, see “How to use the
On the remote control:
Press
.
number buttons” below.
NOTE
• This function works in the same title.
How to use the number buttons
• This function is not available during the repeat playback.
• This feature may not work for some discs.
To select 3:
To select 14:
To select 24:
To select 40:
Press 3.
Press +10, then 4.
Press +10 twice, then 4.
Press +10 three times, then 10.
Or press +10 four times, then 0.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 20 for button locations.
Playback
Locating a desired title/
group using number
buttons
Selecting the desired
title/playlist from the
control display
7 During playback or while stopped.
7 During playback or while stopped
DVD DVD
VIDEO AUDIO
1 Press TITLE/GROUP.
1 Press TOP MENU/PG or MENU/PL.
“_ _” or “_” is shown in the title/group
display area in the display window.
The control display is shown on the TV screen, and the system
starts playback of the first title/playlist.
• The PLAY LIST is shown only when the playlist is on the
DVD VR disc.
Example:
During DVD VIDEO playback
TOP MENU/PG: shows the ORIGINAL PROGRAM.
Example:
_ _
:
:
1 2 3 4 5
.
ORIGINAL PROGRAM
2 While the display window shows “_ _”
or “_”, use number buttons (0-10, +10)
to enter the desired title or group
number.
No Date
Ch
Time
Title
1 25/04/04 4ch 19:00
2 17/05/04 8ch 10:30
3 22/05/04 8ch 17:00
4 26/05/04 L-1 13:19
5 20/06/04 4ch 22:00
JVC DVD World 2004
Music Festival
children 001
6 25/06/04 L-1
8:23
children 002
The system starts playback from the first chapter/track/file of
the selected title/group.
• For details on using the number buttons, see “How to use the
number buttons” (A pg. 22).
*1
*2
*3
*4
*5
*6
*1: Title number
*2: Recording date
NOTE
• This feature may not work for some discs.
*3: Recording source (TV station, the input terminal of the
recording equipment etc.)
*4: Start time of recording
Playing back a bonus
group
*5: Title of the original program/playlist (The title may not be
displayed depending on the recording equipment.)
*6: Current title
Some DVD AUDIOs have a special group called “bonus
group” whose contents are not open to the public. The
DVD
AUDIO
MENU/PL: shows the PLAY LIST.
Example:
bonus group is always assigned to the last group of a disc.
To play back a bonus group, you have to enter the specific “key
number” (a password). The way of getting the key number depends
on the disc. After getting the key number, you can play back the
bonus group by following the procedure below.
PLAY LIST
No Date
Chap Length
Title
1 25/05/04 001 1:03:16
2 17/06/04 005 1:35:25
3 20/06/04 003 0:10:23
4 25/06/04 001 0:07:19
My JVC World
7 While the BONUS indicator lights up on the display window
Favorite music
children001-002
1 Select the bonus group.
For selecting the group, see “Locating a desired title/group
using number buttons” described above.
The key number entry indication appears.
On the TV
*7
*8
*9
*10
*5
*11
*7: Playlist number
*8: Creating date of playlists
*9: Number of chapters
*10:Total playing time
*11:Current playlist
On the display window
_ _ _ _
K E Y
2 Press Y/5 to select the desired title/
The system starts playback of the selected title/playlist.
BONUS
playlist.
2 Press number buttons (0-9) to enter the
key number, then press ENTER.
To clear the control display
• Press ENTER.
When you enter the correct key number, playback starts and
the BONUS indicator goes off.
• If you enter the wrong number, reenter the correct number.
About the play mode on a DVD VR disc
To clear the key number entry
Perform whichever one of the following:
• Open the disc tray.
• Original program (ORIGINAL PROGRAM):
The system can play back the original picture in the recorded
order.
• Turn off the system.
• Playlist (PLAY LIST):
The system can play back the playlist edited by the recording
equipment.
NOTE
• In Random Playback, tracks in the bonus group are not played back.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced operations
DVD
VIDEO
• The icon such as
shows the disc formats or file types the
Using the surround mode
7 Auto Surround (AUTO SUR)
Used to reproduce the sound as it is recorded without any
conversion (downmixing or simulation, etc.). For example, a
multichannel source is automatically reproduced in multichannel
audio.
operation is available for.
IMPORTANT
Before using the remote control for the following
operation;
• Set the remote control mode selector to AUDIO.
• There are exceptions in the operation mentioned
above. In such a case, follow each instruction.
7 Dolby Surround
Dolby Pro Logic II*1
The buttons described below are used on pages 24 to 35.
Dolby Pro Logic II has a newly developed multichannel playback
format to decode all 2 channel sources — stereo source and Dolby
Surround encoded source — into a 5.1 channel.
Dolby Pro Logic II has two modes — Movie mode and Music
mode:
AUDIO
(play button)
Remote control
mode selector
SLOW
SLOW
• Pro Logic II Movie (MOVIE)
Suitable for reproduction of Dolby Surround encoded sources
SLOW
/
MENU/PL
TOP MENU/PG
bearing the mark
• Pro Logic II Music (MUSIC)
.
/PG
/PL
Cursor
(3/2/Y/5)/
ENTER
Suitable for reproduction of any 2 channel stereo music sources.
Dolby Digital*1
Used to reproduce multichannel soundtracks of the software
encoded with Dolby Digital (
).
2
7 DTS Digital Surround*
Used to reproduce multichannel soundtracks of the software
Number buttons
encoded with DTS Digital Surround (
).
DTS Digital Surround (DTS) is another discrete multichannel
digital audio format available on CD and DVD software.
SURROUND
Available Surround modes for each input signal
The B marks show available surround modes.
*1
Surround
off
Auto
Surround
DTSDigital Linear Packed
Surround
Manufactured under
license from Dolby
Laboratories. “Dolby”,
“Pro Logic”, “MLP
Lossless”, and the
double-D symbol are
trademarks of Dolby
Laboratories.
“DTS” and “DTS
Digital Surround” are
registered trademarks
of Digital Theater
Systems, Inc.
Mode
Dolby Surround
DSP
ALL
PCM
PCM
DOLBY
D
3
3
Signal
SURR OFF AUTO SUR MOVIE* MUSIC*
DTS
LPCM
PPCM
3
ST*
Dolby D
(Multichannel)
B
B
B
B
—
—
B
—
—
—
—
—
—
—
Dolby D
(2 channel)
B
B
—
B
*2
DTS Digital
Surround
(Multichannel)
B
B
B
B
—
—
—
—
B
—
—
—
—
—
DTS Digital
Surround
(2 channel)
B
B
—
B
B
*3
You can select these
modes by pressing
SURROUND.
Analog (VCR) or
Linear/Packed
PCM
B
B
B
B
B
B
—
—
—
—
—
—
(2 channel)
(A pg. 25)
Linear/Packed
PCM
(Multichannel)
—
—
B
B
—
24
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
7 All Channel Stereo (DSP)
7 When playing back digital multichannel software
(except during SURR OFF mode)
The appropriate multichannel surround mode (Dolby D, DTS
Digital Surround or Linear/Packed PCM) is automatically selected.
All Channel Stereo (ALL ST) mode can reproduce a larger stereo
sound field using all the connected (and activated) speakers.
All Channel Stereo can be used while reproducing 2 channel stereo
source.
Normal stereo sound
All Channel Stereo
7 When playing back 2 channel source
You can select either mode of Dolby Pro Logic II (MOVIE/
MUSIC) or the DSP (ALL ST) mode.
Press SURROUND repeatedly to select the
desired mode.
The surround mode is turned on and the current surround mode
appears on the display window.
Each time you press the button, the surround mode changes.
7 Indicators on the display window
Digital signal format indicators
For details on each mode, see page 24.
PPCM, SURR:
Lights when DVD AUDIO packed PCM signals
comes in.
To turn off the surround mode
Press SURROUND repeatedly until SURR
OFF appears on the display window.
LPCM, SURR:
GD, SURR:
C, SURR:
Lights when Linear PCM signal comes in.
Lights when Dolby D signals come in.
Lights when DTS Digital (Surround) signals
come in.
Storing adjustments — auto memory
No indication:
No digital signal indicator lights when analog
signals come in.
When you turn the power off, the system memorizes the current
surround mode. The memorized mode is automatically recalled
when you turn the power on.
Dolby Surround/DSP mode indicators
GPLII, SURR: Lights when Dolby Pro Logic II mode is
activated.
NOTE
• When FM or AM is selected as the source, you can select All Channel
Stereo (ALL ST) and SURR OFF mode.
SURR:
Lights when All Channel Stereo mode is
activated.
• For a down-mixing prohibited DVD AUDIO disc, the system
continues to output multi-channel signals with “MULTI CH” shown
on the display window even if the surround mode is turned off during
playback. On the other hand, the system outputs only the front left and
right channel signals with “LR ONLY” shown on the display window
when you start playback with the surround mode having been set to
“SURR OFF” or “H. PHONE”.
Source signal indicators, etc.
Light to indicate the incoming signals.
a: Lights when the left channel signal comes
in.
b: Lights when the center channel signal comes in.
c: Lights when the right channel signal comes in.
d: Lights when the LFE channel signal comes in.
g: Lights when the surround left channel signal comes in.
i: Lights when the surround right channel signal comes in.
h: Lights when the monaural surround channel signal or 2
channel Dolby Surround signal comes in.
SW : Always lights.
Using the on-screen bar
You can check disc information and you can use some functions
using the on-screen bar.
The channel with “ ” shows that the corresponding speakers are
reproducing the channels’ sound.
If the channels’ sound decoded into 5.1 channel is reproduced, only
Showing the on-screen bar
7 Whenever a disc is loaded
DVD DVD DVD
“
” lights.
VIDEO AUDIO VR
Press ON SCREEN.
Each time you press the button, the on-screen bar
changes as follows on the TV screen.
Selecting the surround mode
The system is set up to automatically select the optimal surround
mode for input signal from digital multichannel software.
When playing back 2 channel source, you can select the desired
surround mode manually.
Example:
During DVD VIDEO playback
Dolby D
2/0 . 0ch
IMPORTANT
Before using the remote control for the following
operation;
• Set the remote control mode selector to AUDIO.
Dolby D
2/0 . 0ch
OFF
(The on-screen bar disappears)
(back to the beginning)
• The currently selected item shows green.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
G Shows playback status.
appears during playback.
: appears during fast forward/reverse.
7 Contents of the on-screen bar during playback
DVD VIDEO
:
/
/
: appears during playback in forward slow-motion/
reverse slow-motion.
Dolby D
2/0 . 0ch
:
appears when paused.
:
appears when stopped.
H Select this to change time information (F). See “Changing the
time information” below.
DVD AUDIO
I Select this for Repeat Playback. (A pg. 33)
J Select this for time search function. (A pg. 28)
K Select this for chapter (for DVD VIDEO and DVD VR) or track
(for DVD AUDIO) search function. (A pg. 27)
L Select this to change audio language, channel, or stream.
(A pg. 30)
M Select this to change subtitle language and subpicture.
(A pg. 29)
N Select this to change view angle. (A pg. 29)
O Select this to change the page. (A pg. 31)
P Shows Playback Mode status.
Dolby D
2/0 . 0ch
VCD
SVCD
CD
PROGRAM: appears during Program Playback. (A pg. 32)
RANDOM: appears during Random Playback. (A pg. 33)
Changing the time information
You can change the time information in the on-
DVD DVD DVD
VIDEO AUDIO VR
screen bar on the TV screen and the display
window of the center unit.
7 During playback
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight
.
DVD VR disc
3 Press ENTER repeatedly to select the
desired information.
Dolby D
2/0 . 0ch
PG
1
CHAP
3
TOTAL 0:00:34
DVD-VR
Example:
ON
When elapsed playing time of disc is selected.
A Shows disc type.
B Shows audio information.
C Shows disc number.
7 VCD/SVCD/CD
• TIME: Elapsed playing time of current track
• REM:
Remaining time of current track
D Shows current title (for DVD VIDEO), group (for DVD
AUDIO) number or play mode (for DVD VR).
• TOTAL: Elapsed time of disc
• T. REM: Remaining time of disc
E Shows current chapter number (for DVD VIDEO and DVD VR)
or track number (for other type of discs).
F Shows time information. See “Changing the time information”.
7 DVD VIDEO/DVD AUDIO/DVD VR
• TIME: Elapsed playing time of current chapter/track
• REM:
Remaining time of current chapter/track
• TOTAL: Elapsed time of Title/Group/Program
• T. REM: Remaining time of Title/Group/Program
4 Press ON SCREEN.
The on-screen bar disappears.
NOTE
• When playing back DVD VR, “TIME” and “REM” cannot be shown.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
2 Press number buttons (1-10, +10) to
• For details on using the number buttons, see “How to use the
Playing from a specified
position on a disc
You can start playing a title, chapter or track you specify. You can
select the number of the desired item.
number buttons” (A pg. 22).
To return to the menu
also play a disc from specified time.
Press RETURN.
When “NEXT” or “PREVIOUS” is shown on the TV
screen:
Locating a desired scene from the DVD
menu
DVD VIDEOs generally have their own menus which show
• To go to the next page, press x.
• To return to the previous page, press 4.
DVD
disc contents and you can display them on the TV screen.
You can locate a desired scene by using these menus.
VIDEO
NOTE
• If you want to play a PBC-compatible VCD/SVCD without using the
PBC function, perform any of the following:
7 Whenever a DVD VIDEO is loaded
•
•
Start playback by pressing number buttons while stopped.
Press x repeatedly until the desired track number is displayed,
then start playback by pressing 3 (play button).
The track number appears on the display window instead of
“PBC”.
1 Press TOP MENU/PG or MENU/PL.
The menu appears on the TV screen.
Example:
• To activate the PBC function when playing a PBC-compatible VCD/
SVCD without using the PBC function, perform any of the following:
•
•
Press TOP MENU/PG or MENU/PL.
Press 7 twice to stop playback, then press 3 (play button).
Locating a desired chapter/track using the
on-screen bar
Normally, a DVD VIDEO which contains more than one title
will have a “top” menu which lists the titles. Press
TOP MENU/PG to show the title menu.
Some DVD VIDEO may also have a different menu which is
shown by pressing MENU/PL.
7 During playback
DVD DVD DVD
VIDEO AUDIO VR
See the instructions for each DVD VIDEO regarding its
particular menu.
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Use Cursor 3/2/Y/5 to select a
2 Press Cursor 3/2 to highlight
/
desired item.
.
3 Press ENTER.
3 Press ENTER.
• With some discs, you can also select items by entering the
corresponding number using number buttons.
Example:
During DVD VIDEO playback
Dolby D
Locating a desired scene using a VCD/
SVCD menu with PBC
2/0 . 0ch
A VCD or SVCD recorded with PBC has its own
menus such as a list of contained songs. You can locate
a specific scene by using these menus.
4 Press number buttons (0-9) to enter the
desired chapter number.
Example:
7 During playback with PBC function
To select 8:
To select 10:
To select 20:
To select 37:
Press 8.
1 Press RETURN repeatedly until the
Press 1, then 0.
Press 2, then 0.
Press 3, then 7.
menu appears on the TV screen.
Example:
To correct a misentry
Repeat step 4.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
NOTE
• You can select up to the 99th chapter/track.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
Locating a desired position by specifying
the time
Using the file control
display
You can search and play desired groups and tracks/files
using the file control display on the TV screen.
7 For DVD VIDEO/DVD AUDIO/DVD VR:
During playback
DVD DVD DVD
VIDEO AUDIO VR
For VCD/SVCD:
While stopped or during playback without PBC
Current group/total group Playback mode (PROGRAM,
function
number
RANDOM, REPEAT)
For CD:
During playback or while stopped
Elapsed playing time of current
track (for MP3/WMA only)
Tag information (for MP3/
WMA only)
7 When specifying the elapsed playing time from the
beginning of the disc
Perform the following procedure while stopped.
7 When specifying the elapsed playing time from the
beginning of the current title/track
Perform the following procedure during playback.
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight
3 Press ENTER.
.
Dolby D
2/0 . 0ch
Current group
Current track (file)
Current track (file) / total track
(file) number on current group
Total track (file)
number on disc
4 Use number buttons (0-9) to enter the
time.
Playback status
Example:
To play back from a point 2 (hours): 34 (minutes): 08 (seconds)
elapsed
The file control display appears automatically during playback
(MP3/WMA) or while stopped.
7 For MP3/WMA:
During playback or while stopped
For JPEG:
Press 2
Press 4
Press 3
Press 0
While stopped
1 Press Cursor 3/2/Y/5 to select the
• For MP3/WMA, playback starts from the selected track.
Press 8
To cancel a misentry
Press Cursor 2 repeatedly.
desired group/track/file.
2 Press 3 (play button) or ENTER.
file.
5 Press ENTER.
• Track playback/slide-show starts from the selected track/
6 Press ON SCREEN.
• When you press ENTER for JPEG, only the selected file is
played back.
The on-screen bar disappears.
NOTE
• You can specify time in hours/minutes/seconds for DVD VIDEO/
DVD AUDIO/DVD VR and in minutes/seconds for VCD/SVCD/CD.
NOTE
• (For MP3/WMA) During playback, you can locate the desired track/
file by pressing x/4 or Cursor 5/Y.
• You can also check playback information on the display window.
(A pg. 21)
• Some group, track and file names may not be displayed correctly
depending on recording conditions.
• The order of groups, tracks and files may be displayed differently
from the order displayed on your personal computer.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
Resume Playback
Selecting the subtitle
When Resume Playback is set to “ON” (A pg. 38)
and you stop playback by the following operations,
the position where playback has been stopped is
stored. (“RESUME” appears on the display
window.)
7 During playback of a disc containing subtitles in
several languages
DVD DVD DVD
VIDEO AUDIO VR
DVD DVD DVD
VIDEO AUDIO VR
When using the SUBTITLE button:
1 Press SUBTITLE.
• Turning off the power (A pg. 16)
• Pressing 7 once
Example (DVD VIDEO):
“ENGLISH” is selected out of 3 subtitle languages recorded.
• Changing the source (A pg. 17)
To start playback from the stored position
Press 3 (play button) or DVD.
• There may be a case where 3 (play button) does not work after
changing the source.
2 Press Cursor Y/5 to select the desired
To clear the stored position
Press 7 again or open the disc tray with the playback disc.
subtitle.
For DVD VR
• Pressing SUBTITLE activates the subtitles (subpictures)
regardless of whether the subtitles are recorded or not.
(subpictures will not change if no subpictures is recorded.)
Selecting a view angle
7 During playback of a disc containing multi-view
angles
DVD DVD
VIDEO AUDIO
For SVCD
• An SVCD can contain up to four subtitles. Pressing
SUBTITLE changes the subtitles regardless of whether the
subtitles are recorded or not. (Subtitles will not change if no
subtitle is recorded.)
When using the ANGLE button:
1 Press ANGLE.
Example:
NOTE
The first view angle is selected out of 3 view angles recorded.
• To clear the subtitle, press SUBTITLE. Each time you press
SUBTITLE, subtitle appears and disappears alternately.
When using the on-screen bar:
1 Press ON SCREEN twice.
2 Press ANGLE repeatedly or press
Cursor Y/5 to select the desired view
angle.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight
3 Press ENTER.
.
When using the on-screen bar:
Dolby D
2/0 . 0ch
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight
3 Press ENTER.
.
4 Press Cursor Y/5 repeatedly to select
the desired subtitle.
Dolby D
2/0 . 0ch
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
4 Press Cursor Y/5 to select the desired
NOTE
• To clear the subtitle, press SUBTITLE. Each time you press
SUBTITLE, subtitle appears and disappears alternately.
• Some subtitle or audio languages are abbreviated in the pop-up
window. See “The language codes list” (A pg. 36).
• During DVD AUDIO playback, this feature is available only for the
video part.
view angle.
5 Press ENTER.
6 Press ON SCREEN.
The on-screen bar disappears.
NOTE
• During DVD AUDIO playback, this feature is available only for the
video part.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
Selecting the audio
7 During playback of a disc containing audio in
several languages
Special picture playback
DVD DVD DVD
VIDEO AUDIO VR
Frame-by-frame playback
7 During playback
When using the AUDIO button:
DVD DVD DVD
VIDEO AUDIO VR
Press 8 repeatedly.
Each time you press the button, the still picture
advances by one frame.
1 Press AUDIO.
Example (DVD VIDEO):
“ENGLISH” is selected out of 3 audio languages recorded.
To return to normal playback
Press 3 (play button).
Playing back in slow-motion
7 During playback
DVD DVD DVD
VIDEO AUDIO VR
2 Press AUDIO repeatedly or press
Cursor Y/5 to select the desired audio.
1 Press 8 at the point where
you want to start playback in
slow-motion from.
The system pauses playback.
When using the on-screen bar:
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
2 Press SLOW 9.
2 Press Cursor 3/2 to highlight
3 Press ENTER.
.
• Playback in forward slow-motion starts.
For DVD VIDEO/DVD AUDIO only:
• To play back in reverse slow-motion, press SLOW (.
Dolby D
2/0 . 0ch
Each time you press the button, the playback speed become
faster.
Example: On the TV
4 Press Cursor Y/5 to select the desired
audio.
To return to normal playback
Press 3 (play button).
5 Press ENTER.
NOTE
6 Press ON SCREEN.
• Sound cannot be heard during slow-motion playback.
• During DVD AUDIO playback, this feature is available only for the
video part.
The on-screen bar disappears.
NOTE
• Some subtitle or audio languages are abbreviated in the pop-up
window. See “The language codes list” (A pg. 36).
• “ST”, “L” or “R” is displayed when playing a VCD, SVCD or DVD
VR respectively representing “stereo”, “left sound” and “right
sound”.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
Selecting browsable still picture recorded
on DVD AUDIO
NOTE
• The number of the magnification steps varies depending on the disc
type.
Most DVD AUDIOs include browsable still pictures
(B.S.P.), which usually appear by turns automatically
during playback according to the playback sequence. You
• During slide-show playback of JPEG, zooming in is not available. In
such a case, press 8 to pause slide-show playback, then zoom in.
• During DVD AUDIO playback, this feature is available only for the
video part.
DVD
AUDIO
can change the picture (turn the page) manually when the current
group/track has selectable pictures (pages).
• During playback, there may be a case where Cursor (3/2/Y/5)
does not work in step 2 above.
7 During playback and while the B.S.P. indicator lights up on the
display window
Changing the VFP setting
The VFP (Video Fine Processor) function enables
you to adjust the picture character according to the
type of programming, picture tone or personal
preference.
When using the PAGE button:
DVD DVD DVD
VIDEO AUDIO VR
Press PAGE repeatedly to select a desired
still picture.
When using the on-screen bar:
7 During playback
1 Press ON SCREEN twice.
1 Press VFP.
The on-screen bar appears on the TV screen.
The current VFP settings appear on the TV screen.
Example:
2 Press Cursor 3/2 to highlight
3 Press ENTER.
.
Dolby D
2/0 . 0ch
4 Press Cursor 5/Y to select the desired
still picture.
2 Press Cursor 3/2 repeatedly to select
the VFP mode.
5 Press ENTER.
• NORMAL:Normally select this.
• CINEMA: Suitable for movies.
When you select “NORMAL” or “CINEMA”, press VFP to
complete the setting.
6 Press ON SCREEN.
The on-screen bar disappears.
• USER 1 and USER 2:
Zooming in
7 During playback or while paused
You can adjust parameters that affect picture
appearance.
DVD DVD DVD
VIDEO AUDIO VR
Only when selecting “USER 1” or “USER 2” in step
2, proceed to perform the following operation;
1 Press ZOOM.
magnification changes.
Each time you press ZOOM, scene
3 Press Cursor Y/5 repeatedly to select
a parameter you want to adjust.
2 While zoomed in, press Cursor 3/2/Y/
5 to move zoom-in area.
Adjust gradually and confirm picture appearance results are as
preferred.
• GAMMA:
To return to normal playback
Controls brightness of neutral tints while maintaining
brightness of dark and bright portions.
• BRIGHTNESS:
Press ZOOM repeatedly to select ZOOM OFF.
Controls screen brightness.
• CONTRAST:
Controls screen contrast.
• SATURATION:
Controls screen color depth.
• TINT:
Controls screen tint.
• SHARPNESS:
Controls screen sharpness.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
4 Press ENTER.
2 Follow the instructions that appear on
the TV screen to program the desired
chapters/tracks.
Example:
• For details on using the number buttons, see “How to use the
number buttons” (A pg. 22).
• The content’s numbers that you have to specify for
programming varies depending on the disc type:
5 Press Cursor Y/5 to change the
setting.
•
•
•
DVD VIDEO:
Titles and chapters
Tracks
VCD, SVCD, CD:
6 Press ENTER.
DVD AUDIO, MP3, WMA:
Groups and tracks
The current VFP settings appear again.
• Before you program the tracks in bonus group on a DVD
AUDIO, perform the procedure of “Playing back a bonus
group” (A pg. 23) to turn off the BONUS indicator on the
display window.
7 Repeat steps 3 to 6 to adjust other
parameters.
8 Press VFP.
• You can specify the chapters/tracks whose number is up to
99.
NOTE
• Although the setting display disappears in the middle of the
• There may be a case that the group or title number can be
entered even for discs that contain no groups or titles. In
such a case, press ENTER to proceed to the Track/Chapter
column.
procedure, the setting at that time will be stored.
• When you press ENTER instead of the number buttons in
the Track/Chapter column, “ALL” appears and all the tracks
or chapters on the selected group or title are programmed as
a step.
Program Playback
7 While stopped
DVD DVD
VIDEO AUDIO
To clear the programs one by one from the last
entered number
Press CANCEL repeatedly.
To clear all programs
1 Press PLAY MODE
repeatedly until program
window appears on the TV screen.
Press 7.
You can also clear the program by turning off the system.
3 Press 3 (play button).
If all of the programmed tracks/files have been played back,
playback stops and the program window appears again. Note
that program setting remains.
To check the program contents
During playback, press 7. Playback stops and the program window
appears.
USE NUMERIC KEYS TO PROGRAM TRACKS.
USE CANCEL TO DELETE THE PROGRAM.
To quit the Program mode
While stopped, press PLAY MODE repeatedly until both program
window and
disappear from the TV screen.
NOTE
• There may be a case where bonus group on a DVD AUDIO cannot be
played.
• The Resume function cannot be used with Program Playback.
• Program Playback may not work for some discs.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
Display
window
TV screen
Meanings
Random Playback
You can play titles or tracks on a disc in random
order.
Repeats the current group for
DVD AUDIO/MP3/WMA/
JPEG.
DVD DVD
VIDEO AUDIO
REPEAT GROUP
7 While stopped
Repeats the current title for
DVD VIDEO.
1 Press PLAY MODE
repeatedly until
appears on the TV screen.
(For DVD VR) Repeats the
current title for Original
program.
PG
PL
2 Press 3 (play button).
(For DVD VR) Repeats the
current playlist for Playlist.
• When more than one discs are loaded, the system starts
Random Playback of the next disc after completing current
disc playback.
Repeats all titles and tracks on
the current disc for DVD VR/
VCD/SVCD/CD/MP3/WMA/
JPEG.
DISC
To quit Random mode
While stopped, press PLAY MODE repeatedly until both program
window and disappear from the TV screen.
You can also clear the Random mode by turning off the system.
Repeats all the available discs.
ALL
1
REPEAT ALL
,
NOTE
• The same title/track will not be played back more than once during
Random Playback.
Repeats the current track for
DVD AUDIO/VCD/SVCD/
CD/MP3/WMA.
REPEAT TRACK,
REPEAT STEP
,
Repeats the current chapter for
DVD VIDEO/DVD VR.
REPEAT STEP
Repeat Playback
Repeat mode is off.
The system plays back the disc
normally.
No
indication
Repeating the current selection or all
discs
7 For DVD VIDEO/DVD VR:
During playback
NOTE
• When DVD VIDEO or DVD AUDIO is loaded in the system,
playback of the disc next to the DVD VIDEO or DVD AUDIO will
DVD DVD DVD
VIDEO AUDIO VR
For VCD/SVCD:
During playback without PBC function or
not start, although
/REPEAT ALL on the TV screen or
ALL in the display window is shown.
• For DVD VIDEO and DVD AUDIO, REPEAT ALL and REPEAT
DISC may not be available depending on the disc.
stopped
For DVD AUDIO/CD/MP3/JPEG:
During playback or stopped
When using the on-screen bar (except for MP3/
WMA/JPEG):
When using the REPEAT button:
Press REPEAT.
1 Press ON SCREEN twice.
The on-screen bar appears on the TV screen.
: 3
1
0
1 2
1:
1
2 Press Cursor 3/2 to highlight
3 Press ENTER.
.
Repeat mode indicator
Each time you press REPEAT, the Repeat mode changes.
Dolby D
2/0 . 0ch
4 Press Cursor Y/5 repeatedly to select
the Repeat mode.
5 Press ENTER.
6 Press ON SCREEN.
To cancel Repeat Playback
Select “OFF” in step 4.
The on-screen bar disappears.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
Repeating a desired part [A-B Repeat]
Tray lock
You can lock the tray and prohibit the unwanted disc ejection.
You can repeat playback of a desired part by
specifying the beginning (point A) and ending
(point B).
DVD DVD DVD
VIDEO AUDIO
VR
On the center unit ONLY:
While the system is turned off
7 During playback
1 Press ON SCREEN twice.
DISC 1
The on-screen bar appears on the TV screen.
2 Press Cursor 3/2 to highlight
3 Press ENTER.
.
Press and hold
Dolby D
2/0 . 0ch
• The system turns on and “LOCKED” appears on the display
window.
• If you try to eject the disc, “LOCKED” appears to indicate that
the tray is locked.
4 Press Cursor Y/5 repeatedly to select
“A-B”.
To cancel
Carry out the same operation again.
• The system turns on and “UNLOCKED” appears on the display
window.
5 Press ENTER at the beginning of the
part you want to repeat (point A).
Dolby D
2/0 . 0ch
6 Press ENTER at the end of the part you
A-B Repeat Playback starts.
want to repeat (point B).
7 Press ON SCREEN.
The on-screen bar disappears.
To cancel
Select “OFF” in step 4, then press ENTER.
NOTE
• When playing back a DVD VIDEO/DVD VR, A-B Repeat Playback
is possible only within the same title.
• “A-B” cannot be selected during Program and Random Playback.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 24 for button locations.
Advanced operations
3 Press Cursor 3/2 to make an
Sound and other settings
adjustment or selection.
Example:
IMPORTANT
Before using the remote control for the following
operation;
• Set the remote control mode selector to
C.
D E
D D
AUDIO.
The adjustment is set and the display automatically disappears
a few seconds later.
NOTE
Before you start operation;
• There is a time limit when doing the following steps. If the setting is
cancelled before you finish, start from step 1 again.
NOTE
• When “DD” or “DTS” is selected, if a signal encoded with another
digital format comes in, you cannot listen to the sound. (The
GDIGITAL or C indicator flashes.)
1 Press SETTING.
Example:
C.
D E
A /
C M
P
2 Press Cursor Y/5 to select the item
• DEC (Decode):
you want to set.
When you play an external source (DBS is selected as a
source) that was encoded with Dolby D or DTS Digital
Surround, the following symptoms may occur;
• No sound comes out at the beginning of playback.
• Noise comes out while searching for or skipping chapters
or tracks.
A/PCM (Auto/PCM):
Normally select this. The system automatically
detects the incoming signals.
DD:
Select this if the symptoms above occur when
playing a disc (or software) encoded with Dolby
D.
DTS:
Select this if the symptoms above occur when
playing a disc (or software) encoded with DTS
Digital Surround.
• MON (Monitor Out):
Select the video output jack type by which you watch DVD
playback after connecting your TV. (A pg. 12)
Set the video output to use AV COMPU LINK remote
control system. (A pg. 41)
VIDEO: To watch DVD playback via the VIDEO jack.
S:
COMP (Component):
To watch DVD playback via the COMPONENT
VIDEO OUT jacks.
To watch DVD playback via the S-VIDEO jack.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting DVD preferences
NOTE
• See the following “The language codes list” for the code of each
Using the setup menus
• You can change the language used in the setup menus. See
“Menu description” below.
language, such as “AA”, etc.
The language codes list
Basic operation on the setup menus
AA Afar
IK Inupiak
IN Indonesian
IS Icelandic
IW Hebrew
RN Kirundi
RO Rumanian
RU Russian
RW Kinyarwanda
SA Sanskrit
SD Sindhi
IMPORTANT
Before using the remote control for the
following operation;
1 Set the remote control mode selector to
AUDIO.
AB Abkhazian
AF Afrikaans
AM Ameharic
AR Arabic
JI
Yiddish
2 Press DVD.
AS Assamese
AY Aymara
AZ Azerbaijani
BA Bashkir
BE Byelorussian
BG Bulgarian
BH Bihari
JW Javanese
KA Georgian
KK Kazakh
SG Sangho
SH Serbo-Croatian
SI Singhalese
SK Slovak
KL Greenlandic
KM Cambodian
KN Kannada
KO Korean (KOR)
KS Kashmiri
Cursor
(3/2/Y/5)/
ENTER
SL Slovenian
SM Samoan
SN Shona
BI Bislama
BN Bengali, Bangla KU Kurdish
SO Somali
BO Tibetan
BR Breton
CA Catalan
CO Corsican
CS Czech
KY Kirghiz
LA Latin
SQ Albanian
SR Serbian
SS Siswati
7 While stopped
LN Lingala
LO Laothian
LT Lithuanian
ST Sesotho
SU Sundanese
1 Press SET UP.
CY Welsh
LV Latvian, Lettish SV Swedish
DA Danish
DZ Bhutani
EL Greek
MG Malagasy
MI Maori
SW Swahili
TA Tamil
MK Macedonian
ML Malayalam
MN Mongolian
MO Moldavian
MR Marathi
TE Telugu
TG Tajik
EO Esperanto
ET Estonian
EU Basque
FA Persian
FI Finnish
FJ Fiji
TH Thai
TI Tigrinya
TK Turkmen
TL Tagalog
TN Setswana
TO Tonga
TR Turkish
TS Tsonga
TT Tatar
MS Malay (MAY)
MT Maltese
2 Follow the instructions that appear on
the TV screen.
FO Faroese
FY Frisian
GA Irish
MY Burmese
NA Nauru
NE Nepali
Menu description
GD Scots Gaelic
GL Galician
GN Guarani
GU Gujarati
HA Hausa
NL Dutch
NO Norwegian
OC Occitan
TW Twi
UK Ukrainian
UR Urdu
:Language menu (LANGUAGE)
OM (Afan) Oromo
OR Oriya
UZ Uzbek
VI Vietnamese
WO Wolof
VO Volapuk
XH Xhosa
YO Yoruba
7 MENU LANGUAGE
HI Hindi
PA Panjabi
Some DVDs have their own menus in multiple languages.
• Select the initial language*.
HR Croatian
HU Hungarian
HY Armenian
IA Interlingua
IE Interlingue
PL Polish
PS Pashto, Pushto
PT Portuguese
QU Quechua
7 AUDIO LANGUAGE
Some DVDs have multiple audio languages.
• Select the initial audio language*.
RM Rhaeto-Romance ZU Zulu
7 SUBTITLE
Some DVDs have multiple subtitle languages.
• Select the initial subtitle language*.
7 ON SCREEN LANGUAGE
• Select the language shown on the TV screen when operating this
system.
* When the language you have selected is not recorded to a disc,
the original language is automatically used as the initial
language.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting DVD preferences
:Audio menu (AUDIO)
7 D. RANGE COMPRESSION
(Dynamic range compression)
You can enjoy low level recorded sound clearly at night even at a
low volume when listening to the sound with Dolby Digital.
• AUTO
:Picture menu (PICTURE)
7 MONITOR TYPE
You can select the monitor type to match your TV when you play
DVDs recorded in the picture’s height/width ratio of 16:9.
• 16:9 (Wide television conversion)
Select this when the aspect ratio of your TV is fixed on 16:9
(wide TV).
When you play DVDs recorded in the picture’s height/width
ratio of 4:3, the system adjust the ratio of output signal
automatically.
Select this when you want to enjoy surround sound with its
full dynamic range (no effect applied).
• ON
Select this when you want to fully apply the compression
effect (useful at midnight).
• 4:3 LB (Letter Box conversion)
Select this when the aspect ratio of your TV is 4:3
(conventional TV). While viewing a wide screen picture, the
black bars appear on the top and the bottom of the screen.
• 4:3 PS (Pan Scan conversion)
Select this when the aspect ratio of your TV is 4:3
(conventional TV). While viewing a wide screen picture, the
black bars do not appear, however, the left and right edges of
the pictures will not be shown on the screen.
NOTE
• When you play a multichannel Dolby Digital source with the
surround mode is off, the setting of D. RANGE COMPRESSION is
set to ON automatically.
:Speaker setting menu
(SPK. SETTING)
7 Level menu (LEVEL)
Ex.: 16:9
Ex.: 4:3 LB
Ex.: 4:3 PS
FRONT LEFT SPEAKER/FRONT RIGHT SPEAKER/
CENTER SPEAKER/SURROUND RIGHT SPEAKER/
SURROUND LEFT SPEAKER
NOTE
• Even if “4:3 PS” is selected, the screen size may become “4:3 LB”
with some DVDs. This depends on how DVDs are recorded.
While monitoring the test tone, adjust the center and surround
speakers volume as much as that of the front speakers.
7 PICTURE SOURCE
TEST TONE*
When you set the scan mode to “PROGRESS” (A pg. 18), you can
obtain optimal picture quality by selecting whether the content on
the disc is processed by frame (film source) or by field (video
source) .
Outputs the test tone.
* The test tone comes out of all of the activated speakers in the
following sequence:
Normally set to “AUTO”.
• AUTO
s Front left speaker s Center speaker s Front right
speaker s Surround right speaker s Surround left
speaker s (back to the beginning)
Used to play a disc containing both video and film source
materials.
This system recognizes the source type (video or film) of the
current disc according to the disc information.
• If the playback picture is unclear or noisy, or the oblique
lines of the picture are rough, try to change to other modes.
• FILM
Suitable for playing back a film source disc.
• VIDEO
Suitable for playing back a video source disc.
7 Delay menu (DELAY)
Example:
Center
speaker
1 ms
Subwoofer
Front right
0 ms
7 SCREEN SAVER (A pg. 22)
You can activate or deactivate Screen Saver function.
Front left
0 ms
7 FILE TYPE
When several types of files are recorded on a disc, you can select
which files to play.
• AUDIO
Select this to play MP3/WMA files.
• STILL PICTURE
Select this to play JPEG files.
Surround left
2 ms
Surround right
2 ms
In this case, set the delay time of each speaker as follows;
• Delay time of front speakers: 0 ms
• Delay time of center speaker: 1 ms
• Delay time of surround speakers: 2 ms
FRONT LEFT SPEAKER/FRONT RIGHT SPEAKER/
CENTER SPEAKER/SURROUND RIGHT SPEAKER/
SURROUND LEFT SPEAKER
Adjust the distance from the listening position to the speakers.
Within the range from 0 ms to 15 ms. (by 1 ms)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting DVD preferences
7 Subwoofer menu (SUBWOOFER)
:Other setting menu (OTHERS)
LEVEL
7 RESUME
You can set the output level of the subwoofer in the -6 dB to +6 dB
range.
You can activate or deactivate Resume Playback function.
(A pg. 29)
CROSS OVER
7 ON SCREEN GUIDE
The signals below the preset frequency level will be sent to and be
reproduced by the subwoofer.
You can activate or deactivate the on-screen guide icons.
(A pg. 20)
Select one of the cross over frequency levels according to the bass
sound quality from the front/center/surround speakers.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner operations
IMPORTANT
Before using the remote control for the
following operation;
1 Set the remote control mode selector to
AUDIO.
Manual tuning
1 Press FM/AM repeatedly to select the
band.
2 Press FM/AM.
Example:
NOTE
• When FM or AM is selected as the source, you can select All Channel
When the system is tuned in to 810 kHz.
Stereo (ALL ST) and SURR OFF mode.
AM
8
0 kHz
1
The buttons described below are used on pages 39 to 40.
2 Press TUNING 9/( repeatedly until
you find the frequency you want.
When you hold down the button until the system starts
searching for stations and then release it, the system stops
searching automatically when a station of sufficient signal
strength is tuned in to.
NOTE
• When an FM stereo program is received, the ST indicator lights on the
display window.
FM/AM
AUDIO
Remote control
mode selector
TUNING
TUNING
MEMORY
FM MODE
/
Number buttons
39
Download from Www.Somanuals.com. All Manuals Search And Download.
See page 39 for button locations.
Tuner operations
Preset tuning
Once a station is assigned to a channel number, the station can be
quickly tuned in. You can preset 30 FM and 15 AM stations.
Selecting the FM
reception mode
When the stereo FM program currently tuned in is noisy, you can
change the FM reception mode to improve the reception.
7 To preset the stations
7 While listening to an FM station
1 Tune in the station you want to preset.
Press FM MODE.
The FM reception mode appears on the display window.
Each time you press the button, the FM reception mode changes.
• AUTO:
• If you want to store the FM reception mode for an FM
station, select the reception mode you want. See “Selecting
the FM reception mode” below.
Example:
When a program is broadcast in stereo, you will hear stereo
sound. (The ST indicator lights on the display window.) When in
monaural, you will hear monaural sound. This mode is also
useful to suppress static noise between stations.
• MONO:
When the system is tuned in to 103.5 MHz.
FM
MHz
1 0 3 5 0
.
Reception will be improved although you will lose the stereo
effect. (The MONO indicator lights on the display window.) In
this mode, you will hear noise until you are tuned in to a station.
2 Press MEMORY.
FM
MHz
CH _ _
5 0
1 0 3
.
Reducing the noise of AM
broadcast
When listening to an AM broadcast with a lot of noise interference,
While “CH” and “– –” are flashing:
3 Press number button(s) (1-10, +10) to
• For details on using the number buttons, see “How to use the
select a preset number you want.
you can change the Beat Cut mode to reduce the noise.
7 While listening to an AM station
number buttons” (A pg. 22).
Press FM MODE.
Example:
The current Beat Cut mode appears on the display window.
Each time you press the button, the Beat Cut mode changes.
• Choose “BEATCUT1” or “BEATCUT2” according to which
gives clearer sound.
When the preset channel 1 is selected.
FM
MHz
0
1
1
3 5 0
.
CH
If the setting is cancelled before you finish, start from step 2
again.
While the selected number is flashing:
4 Press MEMORY.
The selected number stops flashing.
The station is assigned to the selected preset number.
If the setting is cancelled before you finish, start from step 2
again.
5 Repeat steps 1 to 4.
• Storing a new station to a used number erases the previously
stored one.
7 To tune in to a preset station
1 Press FM/AM repeatedly to select FM or
AM.
2 Press number button(s) (1-10, +10) to
• For details on using the number buttons, see “How to use the
select a preset number.
number buttons” (A pg. 22).
NOTE
• You can also select a preset number by pressing y /1.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
AV COMPU LINK remote control system
The AV COMPU LINK remote
control system allows you to operate
Available functions
The AV COMPU LINK remote control system allows you to use
the functions listed following.
JVC TVs and VCRs through the center unit. This system is
equipped with the AV COMPU LINK-III, which adds a function to
operate JVC’s video components via the video components
terminals. To use this remote control system, you need to connect
the video components you want to operate as follows.
• Refer also to the manuals supplied with your TV and video
components.
One-touch video play
Simply by inserting a video cassette without its safety tab into the
VCR, you can enjoy video playback without manually setting other
switches. This system automatically turns on and changes the
source to VCR.
The TV automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
When you insert a video cassette with its safety tab in place, press
the play (3) button on the VCR or on the remote control to get the
same result.
Connecting a TV and VCR
CAUTION
Before connecting;
• If you have already plugged your VCR, TV and the center unit into
the AC outlets, unplug their AC power cords first.
One-touch DVD play
Simply by starting playback on the built-in DVD player, you can
enjoy playback without manually setting other switches. The TV
automatically turns on and changes the input mode to the
appropriate position so that you can view the playback picture.
1 Connect the center unit to a TV and
• For details, see page 12 and 13.
VCR.
Automatic selection of TV input mode
2 Connect the center unit to a TV and VCR
using the optional AV COMPU LINK
cords.
When you select DVD or VCR as the source to play on the system,
the TV automatically changes the input mode to the appropriate
position so that you can view the playback picture.
Automatic Power On/Off
The TV and VCR turn on and off along with the system.
When you turn on the system;
Center unit
• If the previously selected source is “DVD”, only the TV will turn
on automatically.
• If the previously selected source is “VCR”, the TV and VCR will
turn on automatically.
When you turn off the system, the TV and VCR will turn off.
NOTE
• If you turn off the system while recording on the VCR, the VCR will
not turn off and will continue recording.
AV COMPU LINK cord
(not supplied)
VCR
TV
3 Plug the AC power cords of the VCR, TV
and the center unit into the AC outlets.
4 Turn on the connected components
first, then turn on the center unit.
• When turning on the TV for the first time after the AV
COMPU LINK connection, turn the TV volume to
minimum using the TV volume control on the TV.
• When turning on the VCR, use the remote control supplied
with this system. (Press F VCR/DBS.)
NOTE
• To correctly use the automatic selection of TV input mode, select the
correct “MON” (Monitor Out) setting. (A pg. 35)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
References
To clean the disc
Wipe the disc with a soft cloth in a straight line
from center to edge.
• DO NOT use any solvent — such as
conventional record cleaner, spray,
thinner or benzine — to clean the disc.
Maintenance
7 Handling Discs
• Remove the disc from its case by holding it at
the edge while pressing the center hole lightly.
• Do not touch the shiny surface of the disc or
bend the disc.
7 Cleaning the system
• Stains on the system should be wiped off with a soft cloth. If the
system is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Put the disc back in its case after use to
prevent warping.
• Be careful not to scratch the surface of the
disc when placing it back in its case.
• Avoid exposure to direct sunlight, temperature
extremes and moisture.
• Since the system may deteriorate in quality, become damaged or
get its paint peeled off, be careful about the following.
•
•
•
•
•
DO NOT wipe it with a hard cloth.
DO NOT wipe it strong.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substance such as insecticides to it.
DO NOT allow any rubber or plastic to remain in contact with
it for a long time.
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
Power does not come
on.
The power cord and/or system cord is not connected.
Connect the power cord and system cord correctly.
(A pg. 13)
The remote control does The batteries are exhausted.
not work.
Replace the batteries. (A pg. 6)
Sunlight is falling directly on the remote sensor.
Hide the remote sensor from direct sunlight.
No sound.
The system cord and/or speaker cord is not connected. Check the connection.
The audio cord is not connected to AUDIO IN (VCR) Connect the cord correctly. (A pg. 13)
and/or DIGITAL IN (DBS) correctly.
An incorrect source has been selected.
The decode mode is not set correctly.
Select the correct source. (A pg. 17)
Select the proper decode mode. (A pg. 35)
Connect the cord correctly. (A pg. 12)
Use a playable disc. (A pg. 3)
No picture is displayed The video cord is not connected correctly.
on the TV screen.
The disc is not playable.
No picture is displayed The scan mode is set to “PROGRESS” though the
on the TV screen, the center unit is connected to the TV which does not
picture is blurred, or the support the progressive video input such as a
Change the scan mode to “INT-LACE”. (A pg. 18)
picture is divided into
two parts.
conventional TV.
Video and audio are
distorted.
The disc is scratched or dirty.
Replace or clean the disc.
A VCR is connected between the center unit and the
TV.
Connect the center unit and TV directly. (A pg. 12)
The picture does not fit The monitor type is not set correctly.
the TV screen.
Set “MONITOR TYPE” properly. (A pg. 37)
Hard to listen to
broadcast because of
noise.
Antennas are disconnected.
Reconnect the antennas correctly and securely.
(A pg. 7)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
References
7 Subwoofer (SP-PWC6)
Amplifier section
Specifications
Front/Center/Surround:
167 W per channel, RMS at 3 C
at 1 kHz, with 10 % total harmonic
7
Center unit
distortion.
167 W, RMS at 3 C at 100 Hz, with 10
% total harmonic distortion.
(XV-THC7/XV-THC6/XV-THC5/XV-THC4/XV-THC3)
Audio section
Total Harmonic Distortion 0.02 %
Subwoofer:
Speaker section
Speaker unit:
Power Handling Capacity: 170 W
NOTE: This value is measured at System cord CONNECTOR for
reference.
Digital input*1:
16 cm (6-5/16 inches) Bass-reflex
Impedance:
Frequency Range:
3 C
30 Hz to 200 Hz
DIGITAL IN (DBS): –21 dBm to –15 dBm
(OPTICAL) (660 nm E30 nm)
* Corresponding to Linear PCM, Dolby Digital, and DTS Digital
Surround (with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz)
1
General
Power Requirements:
Power Consumption:
AC 120 V
, 60 Hz
Video section
Video System:
160 W (at operation)
0 W (in standby mode)
NTSC
500 lines
64 dB
Horizontal Resolution:
Signal-to-Noise Ratio:
Video output level
Composite:
Dimensions (W M H M D):
169 mm M 411 mm M 451 mm
(6-11/16 inches M 16-3/16 inches M
17-13/16 inches)
1.0 V(p-p)/75 C
1.0 V(p-p)/75 C
0.286 V(p-p)/75 C
1.0 V(p-p)/75 C
0.7 V(p-p)/75 C
S-video-Y:
S-video-C:
Mass:
11.5 kg (25.4 lbs)
Component-Y:
Component-PB/PR:
7 Subwoofer (SP-PWC5)
Amplifier section
Video input sensitivity/Impedance (VCR IN)
Front/Center/Surround:
167 W per channel, RMS at 3 C at 1
kHz, with 10 % total harmonic
Composite:
S-video-Y:
S-video-C:
1.0 V(p-p)/75 C
1.0 V(p-p)/75 C
0.286 V(p-p)/75 C
distortion.
167 W, RMS at 3 C at 100 Hz, with
10 % total harmonic distortion.
Subwoofer:
Tuner section
Tuning Range
FM:
Speaker section
Speaker unit:
Power Handling Capacity: 170 W
87.5 MHz to 108.0 MHz
530 kHz to 1 710 kHz
25 cm (9-7/8 inches) Bass-reflex
AM:
General
Power Requirements:
Power Consumption:
Impedance:
Frequency Range:
3 C
25 Hz to 200 Hz
AC 120 V
16 W (at operation)
, 60 Hz
General
Power Requirements:
Power Consumption:
1.3 W (in standby mode)
AC 120 V
, 60 Hz
Dimensions (W M H M D):
160 W (at operation)
0 W (in standby mode)
400 mm M 85 mm M 399 mm
(15-3/4 inches M 3-3/8 inches M
15-3/4 inches)
Dimensions (W M H M D):
264 mm M 481 mm M 459 mm
(10-7/16 inches M 18-15/16 inches M
18-1/8 inches)
Mass:
4.2 kg (9.3 lbs)
7 Subwoofer (SP-PWC7)
Amplifier section
Mass:
16.5 kg (37 lbs)
Front/Center/Surround:
167 W per channel, RMS at 3 C at 1
kHz, with 10 % total harmonic
7 Subwoofer (SP-PWC4)
Amplifier section
distortion.
167 W, RMS at 3 C at 100 Hz, with
10 % total harmonic distortion.
Front/Center/Surround:
167 W per channel, RMS at 3 C at 1
kHz, with 10 % total harmonic
Subwoofer:
distortion.
167 W, RMS at 3 C at 100 Hz, with
10 % total harmonic distortion.
Speaker section
Speaker unit:
Power Handling Capacity: 170 W
Subwoofer:
25 cm (9-7/8 inches) Bass-reflex
Speaker section
Speaker unit:
Power Handling Capacity: 170 W
Impedance:
Frequency Range:
3 C
25 Hz to 200 Hz
16 cm (6-5/16 inches) Bass-reflex
General
Power Requirements:
Power Consumption:
Impedance:
Frequency Range:
3 C
25 Hz to 200 Hz
AC 120 V
, 60 Hz
160 W (at operation)
0 W (in standby mode)
General
Power Requirements:
Power Consumption:
AC 120 V
, 60 Hz
Dimensions (W M H M D):
160 W (at operation)
0 W (in standby mode)
264 mm M 481 mm M 459 mm
(10-7/16 inches M 18-15/16 inches M
18-1/8 inches)
Dimensions (W M H M D):
169 mm M 411 mm M 451 mm
(6-11/16 inches M 16-3/16 inches M
17-13/16 inches)
Mass:
16.5 kg (37 lbs)
Mass:
11.5 kg (25.4 lbs)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
References
7 Subwoofer (SP-PWC3)
Amplifier section
7 Satellite Speakers — SP-XTHC6
Front speakers (SP-THC6F)
Front:
140W per channel, RMS at 4 C at
1 kHz, with 10 % total harmonic
distortion.
Speaker unit:
5.5 cm (2-3/16 inches) M 2
1.5 cm (5/8 inches)
Bass-reflex, Magnetically Shielded
Center/Surround:
Subwoofer:
130W per channel, RMS at 4 C at
1 kHz, with 10 % total harmonic
distortion.
Power Handling Capacity: 170 W
Impedance: 3 C
Frequency Range: 90 Hz to 20 kHz
Dimensions (W M H M D):
140 W, RMS at 4 C at 100 Hz, with 10
% total harmonic distortion.
250 mm M 1 104 mm M 250 mm
(9-7/8 inches M 43-1/2 inches M
9-7/8 inches)
Speaker section
Speaker unit:
Power Handling Capacity: 140 W
16 cm (6-5/16 inches) Bass-reflex
Mass:
2.6 kg (5.8 lbs) each
Impedance:
Frequency Range:
4 C
30 Hz to 200 Hz
Center speaker (SP-THC6C)
Speaker unit: 5.5 cm (2-3/16 inches) M 2
1.5 cm (5/8 inches)
General
Power Requirements:
Power Consumption:
AC 120 V
, 60 Hz
Bass-reflex, Magnetically Shielded
135 W (at operation)
0 W (in standby mode)
Power Handling Capacity: 170 W
Impedance: 3 C
Frequency Range: 90 Hz to 20 kHz
Dimensions (W M H M D):
Dimensions (W M H M D):
169 mm M 411 mm M 451 mm
(6-11/16 inches M 16-3/16 inches M
17-13/16 inches)
320 mm M 75 mm M 92 mm
(12-5/8 inches M 3 inches M 3-5/8
inches)
Mass:
11.5 kg (25.4 lbs)
Mass:
0.9 kg (2.0 lbs)
7 Satellite Speakers — SP-XTHC7
Surround speakers (SP-THC6S)
Speaker unit: 5.5 cm (2-3/16 inches) M 2
Front speakers (SP-THC7F)
Speaker unit:
1.5 cm (5/8 inches)
Bass-reflex
Woofer:
Tweeter:
10 cm (3-15/16 inches) M 4
4 cm (1-5/8 inches)
Bass-reflex, Magnetically Shielded
Power Handling Capacity: 170 W
Impedance:
Frequency Range:
Dimensions (W M H M D):
3 C
90 Hz to 20 kHz
Power Handling Capacity: 170 W
Impedance: 3 C
Frequency Range: 60 Hz to 20 kHz
Dimensions (W M H M D):
250 mm M 1 142 mm M 250 mm
(9-7/8 inches M 45 inches M 9-7/8
inches)
270 mm M 1 085 mm M 310 mm
(10-11/16 inches M 42-3/4 inches M
12-1/4 inches)
Mass:
2.6 kg (5.8 lbs) each
Mass:
8.8 kg (19.4 lbs) each
Center speaker (SP-THC7C)
Speaker unit:
Woofer:
Tweeter:
10 cm (3-15/16 inches) M 2
4 cm (1-5/8 inches)
Bass-reflex, Magnetically Shielded
Power Handling Capacity: 170 W
Impedance: 3 C
Frequency Range: 65 Hz to 20 kHz
Dimensions (W M H M D):
380 mm M 141 mm M 163 mm
(15 inches M 4-9/16 inches M 6-7/16
inches)
Mass:
3.4 kg (7.5 lbs)
Surround speakers (SP-THC5S)
Speaker unit: 8.0 cm (3-3/16 inches)
Bass-reflex
Power Handling Capacity: 170 W
Impedance: 3 C
Frequency Range: 80 Hz to 20 kHz
Dimensions (W M H M D):
111.5 mm M 148 mm M 106.5 mm
(4-7/16 inches M 5-7/8 inches M
4-1/4 inches)
Mass:
0.44 kg (0.97 lbs) each
44
Download from Www.Somanuals.com. All Manuals Search And Download.
References
Surround speakers (SP-THC4S)
Speaker unit: 8.0 cm (3-3/16 inches)
Bass-reflex
Power Handling Capacity: 170 W
7 Satellite Speakers — SP-XTHC5
Front speakers (SP-THC5F)
Speaker unit:
5.5 cm (2-3/16 inches) M 2
Bass-reflex, Magnetically Shielded
Power Handling Capacity: 170 W
Impedance: 3 C
Frequency Range: 80 Hz to 20 kHz
Dimensions (W M H M D):
Impedance: 3 C
Frequency Range: 95 Hz to 20 kHz
Dimensions (W M H M D):
111.5 mm M 148 mm M 106.5 mm
(4-7/16 inches M 5-7/8 inches M
4-1/4 inches)
230 mm M 1 103.5 mm M 285 mm
(9-1/16 inches M 43-1/2 inches M
11-5/16 inches)
Mass:
0.56 kg (1.3 lbs) each
Mass:
3.5 kg (7.8 lbs) each
7 Satellite Speakers — SP-XTHC3
Front speakers (SP-THC3F)
Center speaker (SP-THC5C)
Speaker unit: 5.5 cm (2-3/16 inches) M 2
Bass-reflex, Magnetically Shielded
Power Handling Capacity: 170 W
Speaker unit:
8.0 cm (3-3/16 inches)
1.5 cm (5/8 inches)
Bass-reflex, Magnetically Shielded
Impedance:
Frequency Range:
3 C
90 Hz to 20 kHz
Power Handling Capacity: 140 W
Impedance: 4 C
Frequency Range: 80 Hz to 20 kHz
Dimensions (W M H M D):
Dimensions (W M H M D):320 mm M 75 mm M 92 mm
(12-5/8 inches M 3 inches M 3-5/8
inches)
104.5 mm M 139 mm M 101 mm
(4-1/8 inches M 5-1/2 inches M 4
inches)
Mass:
Surround speakers (SP-THC5S)
Speaker unit: 8.0 cm (3-3/16 inches)
0.90 kg (2.0 lbs)
Mass:
0.56 kg (1.3 lbs) each
Bass-reflex
Power Handling Capacity: 170 W
Center speaker (SP-THC3C)
Speaker unit: 8.0 cm (3-3/16 inches)
1.5 cm (5/8 inches)
Impedance: 3 C
Frequency Range: 80 Hz to 20 kHz
Dimensions (W M H M D):
Bass-reflex, Magnetically Shielded
Power Handling Capacity: 140 W
111.5 mm M 148 mm M 106.5 mm
(4-7/16 inches M 5-7/8 inches M
4-1/4 inches)
Impedance: 4 C
Frequency Range: 80 Hz to 20 kHz
Dimensions (W M H M D):
Mass:
0.44 kg (0.97 lbs) each
137 mm M 105 mm M 104.5 mm
(5-7/16 inches M 4-3/16 inches M
4-1/8 inches)
7 Satellite Speakers — SP-XTHC4
Front speakers (SP-THC4F)
Mass:
0.57 kg (1.3 lbs)
Speaker unit:
8.0 cm (3-3/16 inches)
1.5 cm (5/8 inches)
Bass-reflex, Magnetically Shielded
Surround speakers (SP-THC3S)
Speaker unit: 8.0 cm (3-3/16 inches)
Bass-reflex
Power Handling Capacity: 140 W
Power Handling Capacity: 170 W
Impedance:
Frequency Range:
Dimensions (W M H M D):
3 C
80 Hz to 20 kHz
Impedance: 4 C
Frequency Range: 80 Hz to 20 kHz
Dimensions (W M H M D):
104.5 mm M 139 mm M 101 mm
(4-1/8 inches M 5-1/2 inches M 4
inches)
111.5 mm M 148 mm M 106.5 mm
(4-7/16 inches M 5-7/8 inches M
4-1/4 inches)
Mass:
0.56 kg (1.3 lbs) each
Mass:
0.56 kg (1.3 lbs) each
Center speaker (SP-THC4C)
Speaker unit: 8.0 cm (3-3/16 inches)
1.5 cm (5/8 inches)
Designs & specifications are subject to change without notice.
Bass-reflex, Magnetically Shielded
Power Handling Capacity: 170 W
Impedance: 3 C
Frequency Range: 80 Hz to 20 kHz
Dimensions (W M H M D):
137 mm M 105 mm M 104.5 mm
(5-7/16 inches M 4-3/16 inches M
4-1/8 inches)
Mass:
0.57 kg (1.3 lbs)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
For the U.S.A.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
© 2005 Victor Company of Japan, Limited
0105TMMMDWJEM
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|