JVC DVD Player HR XV1EK User Manual

DVD PLAYER  
Hi-Fi VIDEO  
CASSETTE  
RECORDER  
USER’S GUIDE  
For model:  
HR-XV1EK  
DIGITAL VIDEO  
LPT0716-001A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Precautions  
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow  
for ventilation (10 cm or more on both sides, on top and at the rear.)  
When discarding batteries, environmental problems must be considered and the local rules or laws governing  
the disposal of these batteries must be followed strictly.  
Failure to heed the following precautions may result in damage to the recorder, remote control or video  
cassette.  
1. DO NOT place the recorder ...  
... in an environment prone to extreme temperatures or humidity.  
... in direct sunlight.  
... in a dusty environment.  
... in an environment where strong magnetic fields are generated.  
... on a surface that is unstable or subject to vibration.  
2. DO NOT block the recorders ventilation openings or holes.  
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get  
out.)  
3. DO NOT place heavy objects on the recorder or remote control.  
4. DO NOT place anything which might spill on top of the recorder or remote control.  
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)  
5. DO NOT expose the apparatus to dripping or splashing.  
6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any containers filled  
with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this  
unit.  
7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus.  
8.AVOID violent shocks to the recorder during transport.  
Some Do's And Don'ts On The Safe Use Of Equipment  
This equipment has been designed and manufactured to meet international safety standards but, like  
any electrical equipment, care must be taken if you are to obtain the best results and safety is to be  
assured.  
DO read the operating instructions before you attempt to use the equipment.  
DO ensure that all electrical connections (including the mains plug, extension leads and interconnec-  
tions between pieces of equipment) are properly made and in accordance with the manufacturer's  
instructions. Switch off and withdraw the mains plug when making or changing connections.  
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your  
equipment.  
DO be careful with glass panels or doors on equipment.  
DON'T continue to operate the equipment if you are in any doubt about it working normally, or if it is  
damaged in any way switch off, withdraw the mains plug and consult your dealer.  
DON'T remove any fixed cover as this may expose dangerous voltages.  
DON'T leave equipment switched on when it is unattended unless it is specifically stated that it is  
designed for unattended operation or has a standby mode. Switch off using the switch on the  
equipment and make sure that your family knows how to do this. Special arrangements may  
need to be made for infirm or handicapped people.  
DON'T use equipment such as personal stereos or radios so that you are distracted from the require-  
ments of road safety. It is illegal to watch television whilst driving.  
DON'T listen to headphones at high volume, as such use can permanently damage your hearing.  
DON'T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.  
Overheating will cause damage and shorten the life of the equipment.  
DON'T use makeshift stands and NEVER fix legs with wood screws to ensure complete safety  
always fit the manufacturer's approved stand or legs with the fixings provided according to the  
instructions.  
DON'T allow electrical equipment to be exposed to rain or moisture.  
ABOVE ALL...  
NEVER let anyone especially children push anything into holes, slots or any other opening in  
the case this could result in a fatal electrical shock;  
3
NEVER guess or take chances with electrical equipment of any kind it is better to be safe than sorry!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
Video Cassette Recorder  
Digital AUTO Tracking (ATR  
Function)  
Repeat/Playback  
On-Screen Display in 3  
Language  
AV-Front input jack  
Audio Mixing  
High Quality (HQ) Images  
On-Screen Displays (OSD)  
Nicam Hi-Fi Stereo Audio  
Recording and Playback  
Auto TV Station Tuning and Auto  
Clock Set  
80 Memory for presets  
Auto Time Setting  
30 Minute Back-Up in case of  
Power failure  
6 rotary Head (4 Video Head and  
2 Hi-Fi Audio Head)  
Long play  
Programme Delivery Control  
System  
Timer Recording of up to 8  
Programme per Month  
VIDEO Plus+® rapid timer  
programming  
Instant Timer Recording (ITR)  
Video index Search System  
Slow Motion  
DVD Player  
Digital Audio Jack (Coaxial)  
Multi-Language  
Multi-Angle  
Surround audio  
Repeat Playback  
Memory/Random Playback  
Zoom  
Video Aspect Ratio  
Parental Control  
3 Scene memory  
Digital (Optical or Coaxial) output  
for Dolby Digital (AC-3) and DTS  
Playback of DVD, Video-CD and  
Audio-CD  
PAL & NTSC DVDs playback  
A-B Repeat playback  
MP3 CD playback  
NTSC Video Cassette Tape  
Playback on PAL TV  
Real-Time Tape Counter with  
ZERO RETURN-Function  
PAL  
CassettesmarkedVHS(orS-VHS)canbeusedwiththisvideocassetterecorder.However,S-VHSrecording  
is not possible with this model.  
This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS  
recordings with regular VHS resolution.  
HQ VHS is compatible with existing VHS equipment.  
VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO  
Plus+ system is manufactured under license from Gemstar Development Corporation.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Before using your unit  
Disc playback operation  
Safety Precautions ...........................................2  
Features ...........................................................4  
Contents...........................................................5  
Parts and functions ..........................................6  
Display .............................................................7  
Remote control .................................................8  
Connections and Installation ..........................10  
Playback connection ......................................11  
DISC...............................................................36  
Setting setup language ..................................37  
Playback procedure .......................................38  
Special playback ............................................39  
DVD Picture Signal Selection/Zooming..........40  
Repeat playback ............................................41  
Memory playback/Random playback ............. 42  
MP3 Playback ................................................43  
Changing soundtrack language /  
Setting up the VCR section  
Changing Subtitles language .........................44  
Changing angles / Title selection /  
DVD menu......................................................45  
Tuning the TV Stations and Setting the Time  
and Date Automatically ..................................13  
On-screen Language Selection......................14  
Setting the Time and Date Manually ..............15  
Tuning the TV Stations Manually ...................16  
Setting the VIDEO Plus+ Channel Number  
(Guide CH) .....................................................17  
Advanced function of DVD section  
Parental control ..............................................46  
Setting menu language ..................................48  
Setting audio soundtrack language................49  
Setting subtitle language................................50  
Setting the aspect ratio of TV screen /  
Tape playback operation  
Loading and Unloading a Cassette Tape .......18  
Cassette tape playback..................................19  
Special playback/Playback sharpness/Skip Search ........ 20  
Repeat Playback ............................................21  
Counter Display..............................................22  
Video Index Search System ...........................23  
Setting on Screen display ..............................51  
Setting Audio ..................................................52  
Setting Operation ...........................................53  
Selecting the sound enhancement (E.A.M.)/  
Setting Background/Setting Screen Saver.....54  
Setting initial setup/output sound  
conversion table .............................................55  
Status display of Disc.....................................56  
Table of languages .........................................57  
Recording  
Recording a TV Programme ..........................24  
Instant Timer Recording (ITR) ........................26  
VIDEO Plus+® Recording ...............................27  
Timer Recording Manually .............................29  
Additional information  
Problems and troubleshooting ....................... 58  
Video head cleaning....................................... 59  
Specifications ................................................. 60  
Advanced function of VCR section  
NICAM Stereo Recording  
and Playback..................................................32  
Audio Mixing...................................................34  
Duplicating a Video Tape ...............................35  
* This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents  
and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copy-  
right protection technology must be authorized by Macrovision Corporation or other rights owners and is intended for  
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation or other rights  
owners. Reverse engineering or disassembly is prohibited.  
* Manufactured under license from Dolby Laboratories. Dolbyand the double-D symbol are trademarks of Dolby  
Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.  
* DTSand DTS Digital Outare trademarks of Digital Theater Systems, Inc.  
* Certain audio features of this product manufactured under license from Desper Products,Inc. Spatializer and the  
circle - in - square device are trademarks owned by Desper Products,Inc.  
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe  
the rights of copyright owners and be contrary to copyright laws.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts and functions  
Front  
VCR/DVD mode selector button  
Cassette Loading Slot  
PLAY button  
OPEN/CLOSE button  
EJECT button  
STOP button  
Disc tray  
Display window  
Remote sensor  
Standby/On  
DVD indicator  
REC button  
button  
PR +/buttons  
REW (Rewind) button  
AUDIO (L/R)/  
VIDEO IN jacks  
VCR indicator  
FF (Fast Forward) button  
Rear  
AC power cord  
SCART PRISE PERITEL  
RF IN jack  
RF OUT jack  
DVD OPTICAL  
DIGITAL AUDIO  
OUT jack  
DVD COAXIAL DIGITAL  
AUDIO OUT jack  
SCART-socket  
(for VCR/DECODER)  
DVD AUDIO (L/R) OUT jacks  
DVD S-VIDEO OUT jack  
SCART-socket  
(for TV-RGB/Composite)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Display  
Display window  
1
2
3
4
10  
5
9
8
7
6
No. Display  
Description  
1
2
3
4
5
VCR  
VCR mode of TV/VCR switch  
Playback (lights) / Auto resume (flashes)  
Still picture  
DVD disc is inserted.  
DVD  
CD is inserted.  
CD  
Clock display (colon[ : ] flashes)  
10 : 00  
01 : 00  
2
Counter display by hour/minute at VCR/DVD / by minute/second at CD  
Track number display for CD  
6
TV channel position display  
CH 2  
A1/A2/A3  
External input display  
7
8
Timer recording display  
Video tape is in the unit  
Track display for CD  
9
TRK  
REC  
Normal recording display (flashes during Instant Timer Recording - ITR)  
10  
Note:  
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control  
Page  
14,37  
14  
TV/VCR/DVD switchSwitch to operate TV or VCR or DVD  
Standby/On  
Turn the connected TV on or off  
8
DVD MENU  
MEMORY  
RETURN  
OPEN/CLOSE  
DISPLAY  
A.TRK  
SUB TITLE  
C. RESET  
ANGLE  
Display menu of DVD software  
Index for DVD  
Remove DVD set up menu  
Open or Close the tray  
Change the front Display mode  
Digital AUTO TRACKING  
Set Subtitle of a DVD disc  
Reset the counter to 00:00  
Change playback angle of a DVD disc  
45  
42  
46  
38  
22  
20  
44  
22  
45  
ZERO RETURN Stop the tape when the counter reaches 00:00 22  
(SP/LP)  
PLAY MODE  
ZOOM  
Sets the tape speed for recording  
Select playback mode  
Zoom (for DVD playback)  
Select title of a DVD disc  
24,26,35  
41,42  
40  
TITLE  
45  
REPEAT A-B  
0-9  
Repeat playback between A and B (DVD/CD) 41  
Direct channel selection of TV  
Input setting  
24,26  
16~17,24,26,42,43  
Enter a password  
Scart input or AV-Front input  
VIDEO Plus Recording  
46  
35  
27  
AUX  
PROG.  
Confirmation of Timer Recording  
Set the unit to start recording at a preset time. 28,30  
31  
TV (INPUT) Switch the connected TV to external mode  
8
25  
8
TV/VCR  
TV @ +/–  
8
Switches between TV and VCR  
Adjust the connected TVs volume  
Rewind/Review playback  
Playback  
19,20,39  
19,38,43  
1
9
Fast Forward/Forward search playback 19,20,39  
2
Recording  
Stop  
24,26,35  
19,38,43  
3
4
Still picture/Recording pause on/off 20,24,35,39  
Skip chapter to forward or reverse direction 39  
SKIP 6/7  
INDEX 6/7 Search for the INDEX mark of a tape  
TV/VCR PR +/Select channel of the connected TV or VCR  
23  
JVC TV Remote Control  
This Remote can control some functions  
8,24,26,35  
(
, NUMBER (0-9), TV , TV @ +/,  
C/D  
SET /+  
Cursor buttons  
Setting buttons  
TV PR +/and OK) of a remote controllable  
JVC TV by slide TV/VCR/DVD switch to TV.  
28~30  
Manual tracking buttons in playback mode  
20  
B/A  
Cursor buttons - To move Up in the VCR menu  
you press the A. To move Down in the VCR  
menu you press the B.  
NOTE:  
Its not possible to operate a unit not  
equipped with a remote sensor.  
This Remote can control a JVC TV only.  
When you operate the VCR or DVD, the  
TV/VCR/DVD switch must be slided to  
VCR/DVD again. Otherwise the DVD/  
VCR may not operate properly.  
Since this unit is combined type of DVD  
and VCR, the remote code of DVD is  
individual. So please note that the DVD-  
keys on the RCU of the other JVC  
RECEIVER/TV is not effective for this unit.  
OK  
Enter information in the menu/Select option in the menu  
SET UP MENU  
CANCEL  
Display menu of setup  
Delete Timer program  
14~21,37,46~55  
31  
Cancel input data in the setting mode 27,31,42~46  
Display VCR or DVD operation status 24~25,56  
OSD  
A.MONITOR  
Switches sound  
Change sound track language of DVD  
Slowmotion playback  
33  
44  
20,39  
20  
SLOW  
SKIP SEARCH  
Skip the unwanted short material of a tape  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control  
How to install the batteries  
Use micro batteries type AA.  
Open the battery compart-  
ment cover in the direction of  
the arrow.  
Install two "AA" batteries (not  
supplied), paying attention to the  
polarity diagram in the battery  
compartment.  
Replace the compartment  
cover.  
1
2
3
Battery precautions  
The precautions below should be followed when using batteries in this device:  
1.Use only the size and type of batteries specified.  
2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.  
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.  
3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.  
4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from  
possible battery leakage.  
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.  
Distance of Remote  
Control Operation  
Effective angle:  
approx. 60°  
approx.  
5m  
Point the remote  
control directly at the  
remote sensor.  
Change the custom code for remote control  
If you operate this DVD/VCR with another JVCs VCR simultaneously arranging them side by side, the both  
recorders will react to this remote control. In this case, you can change the remote control and DVD/VCR to  
other frequency (“ ”). Then you can operate only this DVD/VCR with this changed remote control.  
When you purchased, the DVD/VCR and remote control have been set to the frequency-“ ”.  
Example: Change frequency to  
Remote control:  
DVD/VCR:  
While holding VCR, press 2 (code: b) of Number keys.  
(in case of code: A, press 1). Then press OK.  
In the POWER off mode, press and hold PLAY for  
more than 5 seconds. The current code (Aor b) will  
appear on the display. Then press 3 on the remote  
control. The current code of the remote control will be  
transmitted to the unit and the unit will be adjusted to  
the transmitted code. Then the code will disappear  
after approx. 4 seconds.  
NOTE:  
If the remote control has been set to b, the DVD/VCR also must be set to b. Otherwise, the DVD/VCR can not  
be operated with this remote control.  
To reset to A, repeat above procedure. However press 1 instead of 2.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections and Installation  
Connect your DVD/VCR to your home's aerial and to your TV-set as shown in the illustration.  
When you have finished these connections you connect your DVD/VCR to the 230-240 V / 50 Hz mains.  
Aerial  
TV  
TV Scart Socket (A1)  
Aerial-Input  
VCR/DECODER  
Scart Socket (A2)  
RF-Input (from  
house antenna)  
To Scart socket  
DVD/VCR  
RF-Output (to TV)  
AC power cord 230V/50 Hz  
Scart cable (not supplied)  
Supplied Coaxial cable  
Connect a TV with the Scart socket  
In addition to the coaxial cable connection, connect also with scart cable. The picture and sound will be transmitted  
best through the scart cable. In this case, the TV need not be tuned to the video recorder. The Video channel also  
need not be tuned. The video recorder switch the television to video operation through the scart cable automatically.  
The stereo-playback is possible in only case through a scart cable!  
If your TV-set does not switch to video-playback operation automatically, please  
turn your TV's video switch to VIDEO position manually.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback connection  
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is  
dependent on the model and features of each component. Check the Owner's Manual provided with each  
component for the location of SCART socket.  
Connection to a Satellite Receiver  
If a Satellite Receiver is used, we recommend the following configuration:  
SCART-cable (not supplied)  
Satellite  
Aerial  
TV  
DVD/VCR  
Satellite  
Receiver  
SCART-cable (not supplied)  
To record from Satellite Receiver press "AUX" on the remote control of DVD/VCR twice. "A2" will appear  
on the front display. Select the desired TV-program at Satellite Receiver.  
Connect to a TV with S-Video Output  
TV  
S-Video Cord (not supplied)  
DVD/VCR  
Audio (L) Output  
Audio (R) Output  
To S-Video Input  
S-Video Output  
To Audio (R) Input  
To Audio (L) Input  
AUDIO Cord (not supplied)  
Note:  
The S-VIDEO jack is useful only for DVD section.  
If you use the connection with S-Video Cord, set the Video Out Select(P.40) to Video.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback connection  
Connect to a Stereo Amplifier with Audio Output  
If your DVD/VCR is connected to a stereo amplifier, the video soundtrack can output through the loudspeakers of  
the stereo system.  
SCART-cable (not supplied)  
To SCART  
input  
SCART-Socket  
(for TV-RGB/Composite)  
DVD/VCR  
Stereo Amplifier  
Audio (L) Output  
Audio (R) Output  
TV  
To Audio (L) Input  
To Audio (R) Input  
AUDIO Cord (not supplied)  
Connect to an AV Amplifier with built-in digital surround  
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems  
such as Dolby Digital and DTS by using the Coaxial Digital Output.  
Use this connection to connect an:  
• AV amplifier with built-in *Dolby Digital decoder  
• AV amplifier with built-in *DTS decoder  
SCART-cable (not supplied)  
To SCART  
DVD/VCR  
SCART-Socket  
input  
(for TV-RGB/Composite)  
TV  
AV Amplifier with  
Coaxial digital  
Audio Output  
built-in various  
Coaxial digital cable  
(not supplied)  
decoder as above  
Connecting the optical digital cable  
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital  
cable.  
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.  
When not using the optical digital cable, attach the dust protection cap to protect against dust.  
NOTES:  
• The OPTICAL, COAXIAL jacks are useful only for DVD section.  
VHS signal is output only from the SCART-sockets, AUDIO L/R jacks and RF OUT jack.  
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on theAV  
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the  
speakers to be damaged.  
• DTS audio will be output only from the COAXIAL output. To hear DTS audio, DTS-Decoder is necessary.  
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.  
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuning the TV Stations and Setting the Time and  
Date Automatically  
PlugyourDVD/VCRintothemainssup-  
ply and it will start to automatically  
tune itself in and set the correct date  
and time. After setting itself up, you  
must set the TV to the video channel.  
Preparation  
MakesurethatyourDVD/VCRisconnectedproperlytotheTV.  
If a satellite receiver is connected with the coaxial lead, make  
sure its switched ON and set to SKY ONE.  
Turn on the TV and select the channel you wish to allocate for  
video use.  
Plug your DVD/VCR's plug into the mains supply. "Auto"  
1
will start to flash in the display. Your DVD/VCR will auto-  
matically tune itself in and set the correct  
time and date (This may take  
approx. 4 minutes).  
Press and hold the  
button on the front of your DVD/  
2
VCR in the Standby mode until "rF"  
and RF output channel "52" will  
appear in the display.  
If you have used a 21PIN scart lead you now, simply se-  
lect the AV channel on your TV and go to step 5. Tune the  
TV in the same way as tuning in a TV broadcast station  
until the word "TEST" flashes on the TV screen. Refer to  
the TV operating instructions for tuning.  
3
Notes:  
The DVD/VCR automatically corrects  
the clock setting every hour and  
automatically adjusts the clock setting  
for Daylight Saving Time.  
Your DVD/VCR will tune the TV  
stations as follows.  
Now the output from the DVD/VCR is  
tuned to this channel. Whenever you  
want to play back a tape, select this  
channel.  
CH 1  
CH 2  
CH 3  
CH 4  
CH 5  
CH 6  
CH 7  
BBC 1  
BBC 2  
ITV  
Channel 4  
Channel 5  
Satellite  
etc.  
If there is interference in the picture (wavy lines, picture  
roll, etc.), press PR on your DVD/VCR to select any RF  
channel between 23 and 69, retuning your TV until the  
word "TEST" flashes on the TV screen.  
4
If you connected a satellite receiver as explained on page  
11, you must switch off the DVD/VCRs transmitter. Press  
the VCRs PR repeatedly until OFF appears in the display  
window (OFF will appear  
For VIDEO Plus+ recording to work  
correctly, this order should not be  
changed.  
If you want to change the RF output  
channel or switch to "OFF", press and  
after 69 or before 23).  
hold the DVD/VCR  
on the front of  
your DVD/VCR in the Standby mode  
until the current RF output channel  
appears. Press PR on your DVD/VCR  
to select the RF channel you desire.  
Skipped channels still may be selected  
directly through the 1 to 0 keys.  
To cancel skipping select the skipped  
channel using the 1 to 0 keys, then  
press CANCEL. The channel No. does  
not blink any longer, and the channel  
No. now may be selected again using  
PR.  
Press the  
button to turn OFF the DVD/VCR.  
5
Now the TV is tuned to your DVD/VCR.  
To skip a channel position  
Unwanted channels can be  
skipped so that they cannot  
be called up by pressing PR.  
Select the channel to be  
skipped,  
CH 29  
...e.g. channel 29. Select channel 29, then press  
CANCEL.  
This channels number will be flashing. That way you can  
cancel further channels one after the other.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On-screen Language Selection  
Preparation  
Press the  
Turn on your TV and select the VCR  
channel which you have already tuned  
on your TV. The TV will switch to AV  
(VCR mode) automatically by the Scart  
lead connection. The on-screen menu  
can display any of three languages;  
English, German and French.  
button to turn on the DVD/VCR.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.  
Then press VCR to select the VCR mode. (The VCR indicator  
will light)  
Press SET UP MENU. Press L or M to select the  
1
SYSTEM SETUP.  
Then press OK.  
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
OFF  
CHANNEL SETUP  
SYSTEM SETUP  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Press L or M to select  
the LANGUAGE. Then  
press OK.  
2
3
4
SYSTEM SETUP  
CLOCK SET  
LANGUAGE/SPRACHE/LANGUE  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Press L or M to select  
the desired language.  
Then press OK.  
Press SET UP MENU repeatedly until the TV picture  
appears on the screen.  
Notes:  
If the unit does not operate properly,  
or No key operation (by the unit and /  
or the remote control): Static electric-  
ity, etc., may affect the players opera-  
tion.DisconnecttheACpowercordonce,  
then connect it again.  
If you use the unit for the first time and  
press SET UP MENU, instead of the  
MENUscreeninsteps 1and2, theonein  
step 3 may appear. This is normal for this  
DVD/VCR and is no indication of a mal-  
function.  
Please first select the language to oper-  
ate this unit.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Time and Date Manually  
You must set the date and time manually  
Preparation  
for timer recordings if Automatic tuning  
process did not set them correctly.  
Turn on the TV, and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/  
DVD. Then press VCR to select the VCR mode. (The VCR  
indicator will light)  
Example: Setting the clock to 11:30, 26 Oct. 2002.  
Press SET UP MENU. Press L or M to select the SYS-  
1
TEM SETUP. Then press  
OK.  
The step-2 will appear  
when clock is not set.  
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
OFF  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Press L or M to select  
the CLOCK SET. Then  
press OK.  
2
3
SYSTEM SETUP  
CLOCK SET  
LANGUAGE/SPRACHE/LANGUE  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Press  
or  
repeatedly  
until 26 appears. Then  
press M to continue.  
Set the month, year, hour and minute in the same  
4 way as in step 3. Then press OK.  
In case of an error,  
press L to go back to  
one step and enter  
again.  
Notes:  
The AUTO TIME function adjusts the  
clock only if the error is within 5  
minutes.  
The VCR automatically adjusts the  
clock setting for Daylight Saving Time  
once you set AUTO TIME to ON.  
Press  
or  
to select AUTO TIME ON or OFF.  
5
The VCR automatically corrects the clock setting every  
hour once you set AUTO TIME to ON.  
Press SET UP MENU repeatedly until the TV picture  
appears on the screen.  
6
7
The clock will begin operation.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuning the TV Stations Manually  
This VCR has one built-in tuner to  
receive broadcasts. Before you  
record a TV broadcast, you must set and  
presetallchannels. ThisVCRcanpreset  
up to 80 channels.  
Preparation  
Turn on the TV, and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/  
DVD. Then press VCR to select the VCR mode. (The VCR  
indicator will light)  
Example: Preset the BBC 2 on programme position 2.  
Press SET UP MENU.  
Press L or M to select  
the CHANNEL SETUP.  
Then press OK.  
1
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
OFF  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Press L or M to select  
the CH TUNING.  
Press OK to select CH  
TUNING screen.  
2
3
CHANNEL SETUP  
CH TUNING  
GUIDE CH SET  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Press  
once to start the search. It stops at each broadcast  
automatically ("  
changes to " "). Press  
or repeatedly until  
(falling frequency) or  
(rising frequency)  
"
CH  
1
BBC 2 appears. Only in  
case of receiving a weak  
broadcast (drifting  
picture), does search fail  
to stop. If you want to  
SEARCH :  
EXIT  
: MENU  
stop, press  
or  
.
Press OK to preset. The  
search menu screen will  
disappear if the next  
CH  
1
mode is not activated in  
less than 50 seconds.  
CH  
OK  
:
/ 0-9  
: OK  
EXIT : MENU  
CH 01  
CH 02  
CH 03  
CH 04  
CH 05  
CH 06  
BBC 1  
BBC 2  
ITV  
Press L or M repeatedly  
until 2 is displayed. (Or  
enter 0 2 with the 1 to 0  
numbered keys). Then  
press OK.  
4
CH4  
CH5  
SATELLITE  
Note:  
Occasionally, theautosearchmightcatch  
a weak signal and stop. If the TV station  
signal is weak, you shouldn't store this  
station.  
Repeat the steps 3 and 4 to preset other TV stations.  
5
6
Press SET UP MENU repeatedly until the TV picture ap-  
pears on the screen.  
In that case restart the auto search  
using  
or  
.
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the VIDEO Plus+® Channel Number (Guide CH)  
The TV stations must be stored according  
to the tuning guide given on page 13,  
otherwise the VIDEO Plus+ feature will not  
work. If for any reason you did not select  
channels BBC1, BBC2, ITV, CH4, CH5 and  
Satellite in channel positions 1 through to 6  
respectively,youmustseteachVIDEOPlus+  
channel number (GUIDE CH) manually.  
Preparation  
Turn on the TV, and select the VCR channel on TV.  
Press the  
button to turn on the VCR.  
Example: Satellite channel has been incorrectly stored on  
channel 8 of your VCR.  
Press SET UP MENU.  
Press L or M to select  
the CHANNEL SETUP.  
1
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
OFF  
Then press OK.  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Press L or M to select  
the GUIDE CH SET.  
Then press OK.  
2
3
4
CHANNEL SETUP  
CH TUNING  
GUIDE CH SET  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Enter "SAT" with L or M or  
number keys.  
Then press OK.  
GUIDE CH SET  
GUIDE  
CH  
VCR  
CH  
8
6
SET  
OK  
EXIT  
:
/ 0-9  
: OK  
: MENU  
Enter "6" with L or M or  
number keys.  
Then press OK.  
GUIDE CH SET  
GUIDE  
CH  
VCR  
CH  
6
6
If you have connected  
your satellite using the  
scart socket, you must  
select "AV" for the VCR  
CH number.  
SET  
OK  
:
/ 0-9  
: OK  
CLEAR : CANCEL  
EXIT : MENU  
For other Codes, repeat steps 3 and 4.  
5
6
Press SET UP MENU repeatedly until the TV picture  
appears.  
GUIDE CHANNEL TABLE  
TV  
GUIDE CH  
STATION  
BBC1  
BBC2  
ITV  
1
2
3
4
5
6
CH4  
CH5  
Satellite  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Loading and Unloading a Cassette Tape  
Use only video cassette tapes marked  
and  
.
Cassettes marked VHS(or S-VHS) can be used with this video cassette recorder. However, S-VHS recording  
is not possible with this model.  
This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS  
recordings with regular VHS resolution.  
HQ VHS is compatible with existing VHS equipment.  
SQPB playback can be seen only at PAL SP mode.  
Insert the cassette tape with its labeled side facing up  
and the erase prevention tab positioned at your left.  
An inverted cassette tape cannot be inserted.  
Loading  
Push the centre of the tape until it is automatically  
inserted.  
VCR  
Erase prevention tab  
Automatic power ON  
When you insert a cassette tape the DVD/VCR power will turn ON automatically.  
Automatic playback  
When loading a cassette tape without an erase prevention tab, playback will start automatically.  
Unloading  
Press EJECTon the unit. Even if a tape is being  
played, press this button only once.  
Remove the cassette tape.  
1
2
VCR  
VCR  
Automatic tape eject  
This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its  
beginning, the cassette tape will be ejected automatically.  
To prevent accidental erasure  
To record again  
Removetheerasepreventiontabwithascrewdriver.  
Cover the hole with a piece of adhesive tape.  
Screwdriver  
Erase prevention tab  
Adhesive tape  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cassette tape playback  
Preparation:  
Turn ON the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press VCR to select the VCR mode. (The VCR indicator will light)  
Load a prerecorded tape  
1
(When loading a cassette tape  
without the erase prevention  
tab, playback will start auto-  
matically).  
To start playback  
2
Press  
.
Playback will start.  
If the cassette has not loaded  
yet,  
will blink for 4 seconds.  
VCR  
To stop playback  
Press 3.  
VCR  
To rewind the tape or forward it rapidly  
Stop the playback or recording with 3.  
To rewind the tape:  
Press  
To forward the tape:  
Press  
.
.
To stop the tape-winding, press 3. To switch to playback directly  
(without 3), press  
.
Forward/Reverse picture search mode  
When the tape is being winded, you can switch to picture search  
mode(seenextpage).Todothis,press or andholditdown.  
The unit will resume the tape winding as soon as the button is  
released.  
NOTES:  
This VCR selects the playback tape  
speed SP or LP automatically.  
The Cassette tape and DVD disc can  
be played back simultaneously. If you  
press VCR or DVD, the tape playback  
and DVD playback alternate with each  
other on the screen.  
NTSC video cassette playback  
When using a pre-recorded NTSC video cassette tape, the  
connected TV set must operate with a 60 Hz vertical frequency.  
Otherwise the on-screen picture will be affected by vertical  
rolling.EvenifyourVCRsetiscapableofprocessingNTSCvideo  
signals, the picture may be shortened vertically (appearance of  
black bars at the top and at the bottom of the TV screen). The  
dubbing of a NTSC video cassette tape to a standard PAL VCR  
is not possible.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Special playback/Playback sharpness/Skip Search  
Special playback  
Playback sharpness  
Adjust the sharpness of playback picture during playback.  
During slow motion, still picture and picture search,  
sharpness-adjusting is impossible.  
Picture Search  
Reverse picture search function  
Press  
x 1 or x 2 during the playback.  
Start the playback of video tape.  
Forward picture search function  
Press x 1 or x 2 during the playback.  
1
2
To return to playback: Press  
.
Press SET UP MENU.  
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
Press  
or  
to select  
[OFF]  
VCR SETUP. Then press  
Still Picture  
Press 4 during playback. To resume normal  
OK.  
playback: Press  
.
SELECT  
:
VCR  
ENTER : OK  
EXIT  
:
MENU  
Slow Motion  
During playback press SLOW.  
You can change the slow speed by the additional  
pressing of SLOW.  
To return to playback: Press  
Press  
PLAYBACK SHARP-  
NESS. Then press OK.  
or  
to select  
3
4
VCR SETUP  
VCR  
NICAM  
AUDIO MIX  
[AUTO]  
[OFF]  
.
PLAYBACK SHARPNESS  
Slow tracking and vertical lock adjustment  
SELECT :  
If noise bars appear in the picture during slow motion,  
press the SET + or to reduce the noise bars.  
If the still picture jitters excessively, press SET + or –  
to stabilize the still picture.  
ENTER : OK  
MENU  
EXIT  
:
Press  
or  
to adjust  
the playback sharpness  
to the level you reguire.  
Frame by Frame picture  
During playback, press 4 one by one: The picture  
advances frame by frame.  
VCR  
To return to playback: Press  
.
Adjusting tracking condition  
Automatic tracking adjustment  
softer  
sharper  
Whenever you insert a tape and start playback,  
automatic tracking starts working and continuously  
analyzes the signal to enable optimum picture quality  
during playback.  
Press SET UP MENU repeatedly until the TV picture  
appears on the screen.  
5
Note:  
Manual tracking adjustment  
To return to the initial sharpness setting, press CANCEL  
while the sharpness setting screen is appearing.  
If automatic tracking cannot eliminate noises well during  
playback, press SET + or SET to eliminate the noises.  
MANUAL TR.will appear. Press it briefly for a fine  
adjustment, or press and hold for a coarse adjustment.  
Skip Search  
Each time you press SKIP SEARCH while a tape is playing,  
the unit will fast-forward ahead 30 seconds on the tape. You  
may press the button up to six times in a row to move 180  
seconds (three minutes) ahead.  
To return to automatic tracking, press A. TRK.  
Notes:  
The audio output is muted during SPEED SEARCH,  
STILL, FRAME ADVANCE and SLOW MOTION.  
For example:1 press: Approx. 30 seconds of tape  
2 presses: Approx. 60 seconds of tape  
During picture search mode there will be noise bars  
which are caused by the system.  
3 presses: Approx. 90 seconds of tape  
The Special Playback will automatically change to  
playback after approx. 5 minutes to protect the video  
tape against excessive wear.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Repeat Playback  
To set the Repeat function  
If the Repeat function is switched  
on, the playback will continue until  
it reaches the tape-end and then  
rewind to the beginning of the tape.  
This process will repeat until the  
unit is turned off.  
Preparation  
Turn on the TV and select the VCR channel on TV.  
Press VCR to select the VCR mode.  
Press SET UP MENU.  
1
TIMER REC SET  
Press L or M  
AUTO REPEAT  
OFF  
to select the AUTO  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
REPEAT.  
SELECT :  
/
ENTER : OK  
EXIT  
: MENU  
Press  
[ON] or [OFF].  
or  
to select  
2
3
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
ON  
SELECT :  
/
ENTER : OK  
EXIT  
: MENU  
Press SET UP MENU repeatedly until the TV picture  
appears. If "ON" has been selected, the tape will be  
repeatedly played.  
Note:  
To cancel the auto repeat mode, follow  
the above steps 1 and 2, then select "OFF"  
and confirm by pressing SET UP MENU.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Counter Display  
Preparation:  
ZERO RETURN function  
This function makes tape-rewinding  
stop at the counter 00:00:00 position  
automatically.  
Turn ON the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press VCR to select the VCR mode. (The VCR indicator will light)  
Press OSD.  
1
The counter display shows the  
tape running time during  
playback or recording.  
The Recorder will indicate REC  
during recording for itself.  
VCR  
Press C.RESET at the desired  
tape position.  
The counter display will be reset  
to the "00:00:00" position (e.g.  
the beginning of recording).  
2
VCR  
Press 3 when playback or recording is finished.  
Press ZERO RETURN.  
The tape will be rewinded or fast forwarded and automatically  
3
stop at the 00:00:00position.  
Press OSD once again to make the all indicator disappear.  
4
The DISPLAY-button  
Press DISPLAY during the playback. The clock and tape counter  
alternate with each other in the display.  
VCR  
Note:  
You can set the tape counter to 00:00:00 with C.RESET anytime.  
Therefore, the counter display can also indicate 00:00:00, even when  
the tape counter does not reach its beginning yet. Even if the tape  
counter indicates 00:00:00, it can be rewinded moreover. If the tape  
was rewinded over the point of 00:00:00, the minus mark () appears  
in the counter display. Although the tape counter seems to forward  
Note:  
When you load a video cassette, the dis-  
play indication changes to "00:00".  
The counter display does not function  
on non-recorded (blank) sections of the  
tape. When you rewind, fast forward or  
play tapes through blank sections, the  
counter display stops.  
when you press  
, in fact the tape is being rewinded. When the  
tape reaches the beginning, the tape-rewinding stops automatically.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Index Search System  
Example: Indexing of TV commercials.  
Whenever a recording is begun an  
invisible index mark is recorded on the  
tape.These index marks are all identical,  
and each mark means: "Here starts a  
new recording". Every DVD/VCR  
equipped with the Video Index Search  
System (VISS) can locate these marks  
at the beginning of any recording.  
Start playback and wait until the  
end of the TV commercial is  
reached, then press 3.  
1
While holding 2, press  
indication goes off, 3 may be pressed. This short recording  
process will be sufficient to set an index mark.  
once. When the "INDEX" on-screen  
2
This will result in about 10 seconds of the TV commercials to be  
overwritten by another recording. Due to the system the end of  
this recording will be followed by a recording gap (noise signal)  
of approx. 5 seconds.  
Recording several Index Marks  
Due to the system only one index mark will be recorded at the  
beginning of a recording. If you intend to set several index marks  
during a single recording, follow the procedure below:  
At the point of the recording where  
1
an index mark is to be set press 4.  
Theunitwillswitchtotherecording  
pause mode.  
VCR  
REC  
Press PR repeatedly to switch back  
to the original TV program. Press  
4 to resume recording.  
2
VCR  
REC  
Index Search  
Press INDEX + or during stop or play  
mode.  
For Succeeding programs:  
Press INDEX +.  
For Preceding programs:  
Press INDEX .  
(Additional press increases the INDEX  
NO. up to 9.)  
When the INDEX + or is pressed, the  
unit starts searching the INDEX NO.  
selected and finds the portion, then  
playback starts automatically.  
Notes:  
When you record an INDEX mark at  
the very beginning of the tape, the  
mark may not be found.  
During INDEX search, the tape may  
stop and begin to play at a slightly  
different location.  
7 or 6 is displayed  
INDEX may not function properly with  
old or worn out video tapes.  
INDEX marks may not be found if it is  
extremely close to the point where the  
search began.  
Inrecording,ifyoustoprecordingtem-  
porarily, the INDEX mark is not re-  
corded on the tape.  
INDEX NO. (up to 9)  
To stop the Index Search, press 3.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording a TV Programme  
Preparation:  
Turn ON the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press VCR to select the VCR mode. (The VCR indicator will light)  
Load a blank cassette tape with the  
erase prevention tab intact. (The  
DVD/VCR will automatically turn  
1
on.)  
VCR  
Select the program(e.g.29) you want to record with PR +/or  
number keys.  
2
VCR  
1~9 : e.g. 5 = press 5”  
10~80 : e.g. 29 = press 2and 9.  
If a recording in Long Play mode is intended, press  
SPEED) to display "LP". (see Note below)  
(TAPE  
3
4
On the VCR, press 2.  
Or on the Remote, while holding 2,  
press  
.
"
" will appear on the screen for  
about 4 seconds and RECwill  
appear on the display.  
VCR  
REC  
If the erase prevention tab is removed, the tape will eject when  
both the 2 and are pressed for recording. (see p.18)  
To Stop Recording  
Press 3.  
VCR  
To Stop Recording Temporarily  
To stop a recording for a short  
period of time press 4. Press this  
button again if you want to resume  
the recording.  
Notes:  
Since the DVD/VCR has a built-in TV  
tuner the TV set may be turned off when  
recording. The TV set may only be used  
to check for accurate program adjust-  
ments or to monitor recordings.  
You can confirm on the TV-screen  
whether you selected SP or LP. Press  
OSD to see the status display. (see  
page 25)  
VCR  
REC  
Attention:  
A safety circuit turns the pause mode off automatically after 5  
minutes, and the DVD/VCR will stop the recording mode.  
If you wish to watch the DVD playback  
during the normal recording on VCR,  
press DVD to change to DVD mode and  
perform the DVD playback (see page  
38).  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording a TV Programme  
Recording with a SCART Lead:  
Press TV/VCR until "VCR" appears on the display. Select  
the program on the DVD/VCR you want to record. This  
program canbewatchedonthescreenandrecordedbythe  
1
2
You can record a programme using  
theTVreceiveroftheDVD/VCRandat  
the same time watch another pro-  
gramme on the TV set using its re-  
ceiver.AstheDVD/VCRautomatically  
switches the TV set the following  
points should be observed:  
DVD/VCR.  
VCR  
VCRindicator goes on.  
While the VCR is recording press TV/VCR until the "VCR"  
indicator on the display goes off. The TV set now displays  
the program of its built-in receiving module. Select the TV  
channel you want to watch on the TV set. Although the TV  
set now shows another program the DVD/VCR will con-  
tinue recording the previously selected programme.  
REC  
VCRindicator goes off.  
Using TV/VCR you can switch the TV screen between the  
DVD/VCRpictureandtheTVpicture. Ifthe"VCR"indicator  
islitonthedisplay,youwillwatchtheDVD/VCRpicture.This  
has no trouble on the recording.  
3
VCR  
REC  
VCRindicator goes on.  
To Display VCR operation Status  
Press OSD. The clock, day of the week and more informa-  
tions will be indicated.  
To cancel the indicating: Press OSD until all indicator  
disappear.  
Day of the week  
Time  
Deck-status  
here: Playback  
Programme  
number or  
Scart input  
(AV1,AV2 or  
AV3)  
Indication for  
Hi-Fi-playback  
or stereo-  
reception  
23:59 MON  
HI-FI  
CH 80  
STEREO  
01:36:58 SP  
Audio Select  
Cassette in  
Unit  
Tape speed  
Stand of Tape counter  
Auto Rewind Feature  
The DVD/VCR will automatically rewind  
when the tape has ended (except during  
ITR and TIMER REC). It will also eject  
the cassette tape.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instant Timer Recording (ITR)  
Preparation:  
The instant timer recording feature  
provides a simple and convenient way  
to make a timed recording.  
Turn ON the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press VCR to select the VCR mode. (The VCR indicator will light)  
Load a blank cassette tape with the  
erase prevention tab intact. (The  
DVD/VCR will automatically turn  
1
on.)  
VCR  
Select the program (e.g.29) you want to record with PR +/or  
number keys.  
2
VCR  
1~9 : e.g. 5 = press 5”  
10~80 : e.g. 29 = press 2and 9.  
If a recording in Long Play mode is intended, press  
SPEED) to display "LP". (see note on page 28)  
(TAPE  
3
4
Press 2 on the VCR or while holding 2, press  
on  
the Remote to begin recording. Press 2 on the VCR again to  
stop recording after 30 minutes. Each additional press of 2 will  
increase recording time as shown in the chart below, up to a  
maximum of 5 hours. The ITR and  
recording time will appear on the  
screen for about 4 seconds. And,  
REC will keep blinking in the display.  
ITR 0:30  
CH 29  
STEREO  
INDEX  
VCR  
REC  
RECwill keep blinking  
in the display.  
Tape speed: SP  
1:30  
2:00  
1:00  
3:00  
Recording  
0:30  
4:00  
5:00  
Tape speed: LP  
Recording 0:30 1:00  
2:00  
3:00  
1:30  
4:00  
.......  
5:00  
10:00  
To Extend the Recording Time  
While holding 2, press  
repeatedly until the desired time  
appears on the display.  
.
ITR 1 : 30  
CH 29  
Note:  
If you wish to watch the DVD playback  
during the ITR, press DVD to change to  
DVD mode and perform the DVD play-  
back (see page 38).  
If the tape supply has not sufficed for  
ITR recording, the clock symbol ( ) will  
blink at the tape-end and then VCR  
mode will change to DVD mode.  
In this case, press to cancel the  
blink or press EJECT to remove the cas-  
sette tape.  
To stop the ITR  
Press 3.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO Plus+® Recording  
Look up the PlusCode Number in an  
appropriate TV programme magazine.  
Select the desired TV programme for  
recording and refer to the PlusCode  
Number next to it.  
VIDEO Plus+ and PlusCode are  
registered trademarks of Gemstar Development Corporation.  
The VIDEO Plus+ system is manufactured under license  
from Gemstar Development Corporation.  
Preparation  
Turn on the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/  
DVD. Then press VCR to select the VCR mode. (The VCR  
indicator will light)  
Press PROG..  
1
PLUSCODE NO.  
ONCE  
DAILY  
WEEKLY  
Note: If any button is not  
: 0–9  
:
: CANCEL  
: OK  
: PROG.  
PLUSCODE NO.  
SELECT  
CLEAR  
OK  
EXIT  
pressed within 60 seconds,  
the Recorder switches  
back to TV operation.  
Enter the PlusCode  
Number using number  
keys.  
2
3
PLUSCODE NO.  
ONCE  
57378  
DAILY  
WEEKLY  
PLUSCODE NO. : 09  
SELECT  
CLEAR  
OK  
:
In case of an error, press  
CANCEL and enter the  
desired number again.  
: CANCEL  
: OK  
: PROG.  
EXIT  
Press L or M to select ONCE, DAILY or WEEKLY.  
ONCE = To record a  
programme only once  
PLUSCODE NO.  
ONCE  
57378  
DAILY  
WEEKLY  
DAILY = To record TV  
programmes transmitted  
daily  
PLUSCODE NO. : 09  
SELECT  
CLEAR  
OK  
:
: CANCEL  
: OK  
EXIT  
: PROG.  
WEEKLY = To record TV  
programmes transmitted  
once a week.  
Press OK. By the PlusCode Number, the entered data  
appears on the screen.  
4
Select your tape speed.  
PLUSCODE NO.  
57378  
DATE  
START  
END  
CH  
SPEED  
PDC  
15 FRI  
17:30  
18:00  
3
SP  
OFF  
If the entered Number  
is not correct, the  
indicator "PLUS CODE  
ERROR" will appear.  
Enter the correct number.  
Note:  
The built-in timer stores 8 memories. If  
the "PROGRAM FULL" indication  
appears, you must delete one memory  
(see page 31).  
SELECT :  
:
SET  
EXIT  
: MENU  
OK : OK  
When the power supply is interrupted  
for more than 30 minutes, the preset  
programme is cleared. In this case,  
you have to set the timer again.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO Plus+ Recording  
If you have selected Daily or Weekly in step 3, then you  
can select a recording date again. The date must blink.  
If it does not blink, then press L or M repeatedly until  
the DATE blinks. Then press  
or  
repeatedly until  
the desired date appears. The following date options are  
available:  
SUN-SAT: all dates from Sunday to Saturday, or  
MON-SAT: only from Monday to Saturday, or  
MON-FRI: only from Monday to Friday.  
WKL-MON: each Monday, WKL-TUE: each Tuesday  
WKL-SUN: each Sunday, etc.  
Recording period extension  
The recording end-time will be set by VIDEO Plus+  
automatically. However you can extend the recording  
end-time manually. The time END must blink.  
If it does not blink, then press L or M repeatedly until  
the time end blinks. Then press  
to extend.  
Press OK after the confir-  
mation. Then press SET  
UP MENU repeatedly until  
the TV picture appears. To  
enter another programme,  
repeat  
5
6
15 FRI 17:30 18:00 3 SP  
:
:
:
:
:
:
:
:
:
:
:
:
:
:
SELECT :  
EXIT MENU  
/ OK  
steps 1 - 5.  
:
Although the data is stored in the timer memory, the timer  
function is not yet ready for recording. To accomplish this,  
activate it by pressing .  
If no cassette tape is loaded, the  
clock symbol does not appear.  
Note:  
As long as the timer is activated (clock  
symbol indicated on the display), you  
cannot use the VCR. If you want to use  
the VCR, first press to deactivate the  
timer.  
Not all TV Stations transmit PDC signal  
all of the time, therefore it is advisable to  
check before setting PDC to ON, if you  
do set PDC to ON and no signal is  
received your recording might not take  
place at all. To check PDC status,  
change to the channel on your DVD/VCR  
you wish to record from, if the word  
"PDC" appears on the screen for a few  
seconds then that channel is  
To record with the PDC (Programme  
Delivery Control)  
system  
TIMER REC SET  
The PDC system starts  
DATE  
START  
END  
15 FRI  
17:30  
18:00  
3
recording when it picks up a  
special signal transmitted  
by the broadcaster with the  
TV programme even if the  
TV programme starts early,  
CH  
SPEED  
PDC  
LP  
ON  
SELECT :  
:
SET  
EXIT  
: MENU  
OK : OK  
late or runs on longer than scheduled. In step 4, press  
M repeatedly until PDC OFF flashes, then press  
or  
to display "ON" for recording with PDC.  
broadcasting PDC and you can set the  
feature to ON.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Recording Manually  
Preparation  
Turn on the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/  
DVD. Then press VCR to select the VCR mode. (The VCR  
indicator will light)  
The built-in timer allows unattended  
recording of up to 8 programmes  
within 1 month.  
Load a video cassette with the erase prevention tab intact.  
Make sure that the time and date are correct.  
Example: Timer recording for the 23rd, Friday, on channel 3,  
19:30 to 21:30 and LP mode.  
Press SET UP MENU.  
1
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
OFF  
Press L or M to select  
the TIMER REC SET.  
Then press OK.  
SELECT :  
ENTER : OK  
EXIT  
: MENU  
Each line stands for one  
programme of the 8  
memories. Select one  
line with L or M .  
2
3
4
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Then press OK.  
SELECT :  
EXIT MENU  
/ OK  
:
Set the desired dates with  
TIMER REC SET  
or  
. Then press M  
DATE  
START  
END  
23 FRI  
11:30  
to accept them.  
:
1
CH  
Daily/weekly settings  
can be found by  
SP  
SPEED  
PDC  
SELECT :  
OFF  
pressing  
or  
SET  
EXIT  
:
repeatedly (see page  
30).  
: MENU  
Set the Starting time (19:30), ending time (21:30)  
channel (3) and tape speed (LP) in the same way as in  
step 3.  
TIMER REC SET  
DATE  
START  
END  
23 FRI  
19:30  
21:30  
3
CH  
Note:  
LP  
OFF  
SPEED  
PDC  
SELECT :  
In case of an error,  
press Ltogobackto  
the previous step and  
repeat.  
Whenthepowersupplyisinterruptedfor  
more than 30 minutes, the preset  
programme is cleared. In this case, you  
have to set the timer again.  
SET  
EXIT  
:
OK : OK  
: MENU  
If you want to set the timer with the PDC  
function, see "To record with the PDC  
system" on page 28.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Recording Manually  
Press OK to accept them.  
Toenterotherprogrammes,  
repeatsteps 2to4, orpress  
SET UP MENU repeatedly  
untiltheTVpictureappears.  
5
23 FRI  
19:30 21:30 3 LP  
:
:
:
:
:
:
:
:
:
:
:
:
:
:
SELECT :  
/ OK  
EXIT  
:
MENU  
Note:  
In case of a timer recording from the Scart  
socket, proceed as follows: When "CH" is  
Although the data is stored in the timer, it is not ready for  
6
recording. To start timer recording, press  
to turn it on.  
blinking in picture/step 4, press  
or  
When no video cassette is loaded, the clock symbol does  
not appear.  
repeatedly until "AV" appears.  
If the clock symbol blinks when the timer  
recordingiscompleted,theTVprogramme  
has not been completely recorded  
because of an insufficient tape supply.  
As long as the timer is activated (clock  
symbol indicated on the display), you  
cannot use the DVD/VCR. If you want to  
use the DVD/VCR, press to deactivate  
the timer.  
When you turn the unit off, the timer will be switched on  
automatically. The clock symbol will appear on the display.  
If you still want to use the recorder, press first. Then  
the clock symbol will disappear from the display.  
Weekly (e.g. WKL-TUE: each Tuesday) or daily (e.g.  
MON-SAT Monday to Saturday) Timer recording  
Follow the procedure for timer recording on the previous  
page. In picture/step 3 (when date and day is blinking),  
press  
repeatedly until the desired setting appears  
(weekly or daily).  
DATE-DAY  
SUN-SAT  
WKL-FRI  
MON-SAT  
WKL-SAT  
WKL-SUN  
WKL-WED  
WKL-MON  
WKL-TUE  
MON-FRI WKL-THU  
Set other START, END, CH, SPEED as previous pages.  
In case of overlapping Timer programmes  
Do not overlap timer programmes as portions of the  
conflicting programmes will be lost. The first recording  
time has priority over the next recording time as  
shown in the diagram below.  
8 : 00  
9 : 00  
10 : 00  
11 : 00  
Program 1  
Program 2  
Note:  
The daily/weekly recording can be  
Deleted Parts  
made continuously until the recording is  
cancelled or the tape reaches the end.  
During timer recording, the automatic  
rewinding mechanism does not function.  
Program 3  
Non Recorded Portion Parts  
Recording  
Control Settings  
Prog.1  
Prog.2  
Prog.3  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Recording Manually  
Confirmation/Cancellation of the Timer Recording  
If the Timer has been activated, now press to deacti-  
1 vate the timer. The clock symbol will disappear. Then press  
VCR to change to VCR mode.  
To confirm a Timer programme.  
2
28 FRI  
19:30 21:00  
3 LP  
1 SP  
3 LP  
Press PROG. twice. All  
thetimerprogrammeswill  
appear.  
30 SUN 12:15 13:00  
30 SUN 19:00 22:00  
:
:
:
:
:
:
:
:
:
:
SELECT :  
CLEAR  
/ OK  
:
CANCEL EXIT : MENU  
To cancel a Timer programme.  
3
28 FRI  
19:30 21:00  
3 LP  
1 SP  
30 SUN 12:15 13:00  
Press L or M to select  
the timer programme you  
wish to cancel.  
:
:
:
:
:
:
:
:
:
:
:
:
Then press CANCEL.  
This line is now cancelled.  
SELECT :  
EXIT  
/ OK  
MENU  
:
Press SET UP MENU (or PROG.) button repeatedly until  
4 the TV picture appears.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NICAM Stereo Recording and Playback  
This DVD/VCR is capable of recording  
sound in Hi-Fi system. The recording  
will be performed automatically.  
NICAM STEREO broadcasts are  
recorded in its original sound system  
regardless of the setting. If you wish  
to record NICAM programmes, select  
NICAM "AUTO" as follows.  
Preparation:  
Turn ON the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press VCR to select the VCR mode. (The VCR indicator will light)  
NICAM stereo sound reception:  
Press SET UP MENU. Press  
L or M to select VCR SETUP.  
Then press OK.  
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
1
[OFF]  
SELECT  
ENTER  
EXIT  
:
:
:
OK  
MENU  
Press L or M to select NICAM.  
VCR SETUP  
2Then press  
/
or OK to  
NICAM  
AUDIO MIX  
PLAYBACK SHARPNESS  
[AUTO]  
[OFF]  
select [AUTO].  
/
SELECT  
ENTER : OK  
MENU  
:
EXIT  
:
Press the SET UP MENU repeatedly until the TV picture  
3 appears.  
NICAM programmes are divided into 4 types as  
shown below.  
NICAM STEREO broadcast  
"NICAM ST" illuminates when a  
NICAMSTEREObroadcastsignalis  
NICAM ST  
received.  
NICAM MONO A broadcast  
"NICAM M1" illuminates when a  
NICAM MONO A broadcast signal is  
NICAM M1  
received.  
NICAM MONO A B broadcast  
"NICAM M1/2" illuminates when a  
NICAM MONO A and MONO B  
NICAM M1/2  
broadcast signal is received.  
Note:  
When listening to a stereo broadcast or  
playing back a tape Hi-Fi recorded in  
stereo, you have to connect the DVD/  
VCR with the stereo audio system or the  
stereo TV. The sound which is output  
from the RF OUT jack is monaural.  
NICAM OFF  
It will be displayed for the NICAM  
signal when the "NICAM [OFF]" is  
selected in menu screen.  
NICAM OFF  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NICAM Stereo Recording and Playback  
Playback  
Use A.MONITOR to select under stereo/mono or bilingual  
playback. See the table below for more information.  
On-screen indications  
(for 4 sec.)  
Bilingual playback  
performed as follows:  
Stereo playback  
performed in:  
Simultaneously  
both languages  
from HiFi track  
(Mixed sounds)  
Stereo  
Left channel signal One's mother  
output from both  
loudspeakers  
tongue dubbing  
(Main sound)  
L
CH  
Right channel  
Original sound  
signal output from  
both loudspeakers  
track (Sub sound)  
R
CH  
Mono  
One's mother  
tongue dubbing  
(Main sound)  
HiFi signal indication  
It will be displayed for approx. 4  
secondswhenplayingHiFivideo  
cassette tapes.  
HI-FI  
Note:  
WhenplayingHiFicassettetapesrecorded  
on another VCR, the sound output may be  
distorted. This is normal and no indication  
ofaunitmalfunction.Trytominimizesound  
distortions by using SET +/or change to  
MONO by pressing of A.MONITOR.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Mixing  
Preparation:  
Youcanlistentobothsoundtracks(Hi-  
Fi and MONO), by setting AUDIO MIX-  
ING mode.  
Turn ON the TV and select the VCR channel on TV.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.  
Then press VCR to select the VCR mode. (The VCR indicator  
will light)  
Press SET UP MENU.  
1
TIMER REC SET  
AUTO REPEAT  
VCR SETUP  
CHANNEL SETUP  
SYSTEM SETUP  
Press  
or  
to select  
[OFF]  
VCR SETUP. Then press  
OK.  
SELECT  
:
ENTER : OK  
EXIT  
: MENU  
Press  
or  
to select  
2 AUDIO MIX.  
VCR SETUP  
NICAM  
AUDIO MIX  
[AUTO]  
[OFF]  
PLAYBACK SHARPNESS  
SELECT :  
/
ENTER : OK  
MENU  
EXIT  
:
Press  
/
or OK to select  
VCR SETUP  
3 [ON].  
NICAM  
AUDIO MIX  
PLAYBACK SHARPNESS  
[AUTO]  
[ON]  
If you select [ON], the unit  
will play both sound tracks  
(Hi-Fi and MONO) until the  
AUDIOMIXINGmodeiscan-  
celled.  
SELECT :  
/
ENTER : OK  
MENU  
EXIT  
:
Press SET UP MENU repeatedly until the TV picture  
4 appears.  
Note:  
To deactivate the AUDIO MIX function  
follow the above procedure from step 1 to  
3, select [OFF], and confirm the setting  
by pressing SET UP MENU.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Duplicating a Video Tape  
When you try to connect with a cable, make sure the power of both units have been turned off.  
Connect the recording unit with the TV. Therefore you can just watch what the recording unit is recording.  
Load a blank cassette tape with the erase prevention tab  
While holding 2, press  
and then 4 of Recording unit.  
3
4
1 intact into the recording DVD/VCR. Load the previously  
recorded cassette tape into the playback VCR or a video  
camera.  
Press PLAY-button and then PAUSE/STILL-button of  
Playback unit. Now you can see the still picture of the  
scene that you wish to duplicate.  
VCR  
Press 4 of both units simultaneously to start the Duplicat-  
5 ing.  
Use AUX or PR of the recording DVD/VCR to select the  
2 "A1", "A2" or "A3" instead of the preset channel.  
Note:  
A1 = TV-RGB/Composite Scart Socket  
A2 = VCR/DECODER Scart Socket  
A3 = Front AV jacks  
Beforestartingtheduplicatingprocess,selecttheproper  
tape speed using  
correct tape speed will be set automatically during  
playback.  
. For a pre-recorded tape the  
Connection with second Video recorder or Video camera  
OR  
Playback on  
camera  
Playback unit  
Recording unit  
(not  
supplied)  
(not supplied)  
Press AUX on the  
recording unit repeatedly  
until A3 appears.  
Duplicating a disc material onto a video tape  
You can record disc material in DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR only.  
If the DVD disc has a Copy-guard feature, the duplicating is not possible. A symbol mark “  
will appear  
on the screen for approx. 4 seconds. See page 38 for more information about the DVD playback.  
Preparation:  
Load a cassette tape with the erase prevention tab  
intact.  
During disc playback, while holding 2, press  
.
3
Select the tape speed in the VCR mode. (see P.24)  
Load a disc you wish to duplicate.  
Note:  
Press DVD to select the DVD mode. (The DVD indi-  
cator will light)  
1
You can set the duplicating time using the ITR-function.  
At step 3 above press 2 repeatedly until the desired  
duplicating time appears on the screen.(P.26)  
Press  
to start the disc playback.  
2
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disc  
This unit applies to DVD discs from Region 2 only.  
The loaded Disc (DVD, Video-CD, Audio-CD and MP3-CD) will be recognized automatically.  
The suitable Disc-formats are: DVD, CD-R and CD-RW.  
Some CD-R/RW discs may be incompatible.  
This DVD/VCR uses the PAL color system. The NTSC-DVDs can be playback on PAL 60Hz.  
Do not play DVD-ROM, DVD-Audio, CDV, CD-G or Photo CD to prevent accidental erasure of prerecorded material.  
Some DVDs is played back with a Copy guard system. In case of a dubbing on video tape, strong disturbance may  
occur. This is not a defect of this DVD/VCR.  
DVD DISC  
Title  
TITLE1  
CHAPTER 1  
TITLE2  
When two or more movies are recorded on a disc,  
the disc is divided into two or more sections. Each  
section is called a TITLE.  
CHAPTER 2  
CHAPTER 1  
CHAPTER 2  
CHAPTER 3  
Chapter  
The titles can be subdivided into many sections.  
Each section is called a CHAPTER.  
Audio-CD  
Track  
TRACK  
1
TRACK  
2
TRACK  
3
TRACK  
4
TRACK  
5
An Audio CD can contain several items.  
These are assigned to the tracks.  
Removing Disc from Case  
Be sure to hold the edge of disc. Do not touch the surface of the disc.  
Pick up the disc gently from the case.  
Do not scratch the disc.  
Do not get dirt on the surface of the disc.  
Do not stick a label or adhesive tape on the disc.  
Do not drop or bend the disc.  
Storing Disc  
Store the disc in the case to avoid risk of scratches, dirt or damage.  
Do not leave disc exposed to direct sunlight or in hot or humid places.  
Cleaning Disc  
Wipe the disc with a clean, dry cloth from centre to edge.  
Do not wipe the disc round.  
Do not use liquid or aerosol cleaners.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting setup language  
The setup language can be selected.  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.  
When using an amplifier, switch on the amplifier.  
Press DVD to select the DVD  
1
mode. (The DVD indicator will  
light.)  
No Discwill appear on the  
screen. (If a DVD disc has al-  
ready loaded, the playback will  
No Disc  
start automatically.)  
PressSETUPMENU inthestop  
2
mode. The SETUP MENU of  
Picture  
DVD will appear on the screen.  
TV Shape 4:3LB  
Video Out Select Video  
Then press  
or  
to select  
Language.  
: Select  
: Enter  
Press  
/
toselectOn-Screen  
3
Language, then press OK (En-  
ter).  
Language  
On-Screen Language ENG  
Disc Menu Language ENG  
Audio Language  
Subtitle Language  
ENG  
ENG  
: Select  
: Enter  
Press  
/
to select desired  
4
5
C
language: English (English),  
German (Deutsch) or French  
(Français).  
Language  
On-Screen Language ENG 
Disc Menu Language ENG 
Audio Language  
Subtitle Language  
ENG
ENG  
: Select  
: Enter  
To make the SETUP screen disappear, press SET UP MENU  
(or RETURN).  
If the DVD/VCR does not operate  
properly: Static electricity, etc., may  
affect the player's operation. Disconnect  
the AC power cord once, then connect  
it again.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback procedure  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Press OPEN/CLOSE.  
1
The disc tray will open.  
Place a disc onto the tray.  
2 Hold the disc, position it with the  
printed label side up, align it with  
the guides, and place it in its  
proper position.  
Press  
or OPEN/CLOSE.  
3
4
The disc tray closes automati-  
cally.  
On the screen,  
changes to  
and then playback will  
commence.  
Amenu screen may appear on  
the TV screen, if the disc has  
a menu feature. In this case,  
press  
,
,
,
or OK to  
operate a menu feature.  
Press 3 to end playback.  
The DVD/VCR memorizes the stopped point, depending on  
the disc. To Return To The Last Scene Viewed, Press Play. To  
Disable This Operation, Press STOP Again.appears on the  
screen for approx. 4 seconds. “ ” will continue blinking in the  
display until the playback is stopped completely. Press  
resume playback (from the scene point).  
to  
If you press 3 again (3 appears on the screen) or unload  
the disc, the DVD/VCR will clear the stopped point.  
Then press OPEN/CLOSE.  
5 The disc tray opens.  
Remove the disc and press  
, (POWER).  
The disc tray closes automatically and DVD/VCR turns off.  
NOTES:  
If a non-compatible disc is loaded, "Please Check Disc", "Disc playback unauthorized Consult owners manual  
for further information" or "Parental Lock" will appear on the TV screen according to the type of loaded disc. In  
this case, check your disc again (See pages 36 and 46, 47).  
Some discs may take a minute or so to start playback.  
A Prohibitionsymbol  
may appear at the upper right of the screen. This symbol means either the feature you  
tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate  
a problem with the DVD/VCR.  
When you set a single-faced disc label downwards (ie. the wrong way up) and press  
or OPEN/CLOSE, "  
"
will appear and remain on the screen for approx. 30 seconds and then it will change to "Please Check Disc".  
Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays  
DVDs according to the disc contents the software producers designed, some playback features may not be  
available. Also refer to the instructions supplied with the DVDs.  
When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid  
possible damage to the audio system, the consumer should take proper precautions when the analog stereo  
outputs of the DVD/VCR are connected to an amplification system.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Special playback  
Note: There may be a slight delay be-  
tween pressing the button and the  
function activation.  
Fast Forward Playback  
Press  
during normal playback.  
Each press of  
will increase the speed of the search x2 ( ), x8  
(
(
), x30 (  
) are available)  
), x100 (  
). (in case of Audio-CD: x4 ( ) and x8  
To resume normal playback, press  
.
Review Playback  
Press  
during normal playback.  
Each press of  
will increase the speed of the search x2 ( ), x8  
), x100 ( ). (in case of Audio-CD: x4 ( ) and x8  
(
(
), x30 (  
) are available)  
To resume normal playback, press  
.
Still Playback  
Press 4 during normal playback.  
To resume normal playback, press  
.
Frame Advance  
Press 4 during still playback.  
One frame is advanced each time  
you press 4.  
To resume normal playback, press  
.
Slow-motion Playback  
Press SLOW during normal playback or still playback.  
Each press of SLOW will change the speed of the slow x1/2, x1/4,  
x1/8.  
NOTES:  
The unit is capable of holding a still  
video image or On screen display image  
on your television screen indefinitely. If  
you leave the still video image or On  
screen display image displayed on your  
TV for an extended period of time, you  
risk permanent damage to your  
television screen. Projection televisions  
are very susceptible.  
To resume normal playback, press  
To resume the still playback, press 4.  
.
Locating a chapter or track  
T
1
C
1
Press SKIP (  
) Forward or SKIP  
(
) Reverse during playback to  
Some titles may not display chapter  
numbers.  
locate a chapter or track that you  
want to watch.  
Each time you press the button, a  
C (chapter)number or T (track)”  
number is skipped.  
When you set Title Stopto Off(See  
page 53), you can access chapter in  
another title. If you go back to the  
preceding title by pressing the SKIP, the  
DVD/VCR locates the first chapter of the  
title. When Title Stopis set to On.  
you can access chapters only within the  
current title.  
When you press SKIP (  
), playback starts from the beginning  
of the current chapter or track.  
When you press SKIP (  
) twice, playback starts from the  
beginning of the preceding chapter or track.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Picture Signal Selection/Zooming  
Preparation:  
You can select the output signal of  
DVD playback picture to the TV  
screen as an VIDEO signal or a RGB  
signal.  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.  
Then press DVD to select the DVD mode. (The DVD indicator  
will light)  
Press SET UP MENU in the  
stop mode.  
1
Picture  
TV Shape 4:3LB  
Video Out Select Video  
Press  
ture, then press  
or  
to select Pic-  
or to  
select Video Out Select.  
: Select  
: Enter  
Press OK (Enter).  
2
3
Press  
or  
to select the  
Picture  
TV Shape 4:3LB  
Video Out Select Video  
Video  
RGB  
desiredpicturesignal,Video”  
or RGB.  
: Select  
: Enter  
To make SETUP screen disappear, press SET UP MENU.  
Notes:  
If you use the connection with S-Video cord, be sure to set the  
Video Out Selectat step 2 above to Video. If you select RGB,  
the TV screen will be disturbed.  
If you selected RGBat step 2 above, press TV/VCR to select  
VCR. (VCR indicator will appear on the display) Otherwise, the  
TV screen will be disturbed when you select the channel with  
TVs CHANNEL UP/DOWN buttons.  
Zooming  
This unit will allow you to zoom in on the frame image. You  
can then make selections by switching the position of the  
frame.  
PressZOOMduringplayback.  
1 The centre part of the image  
will be zoomed in.  
As you repeatedly press the  
ZOOM  
EXIT  
OKorZOOMwhileZOOMis  
selected, the magnification  
levelchanges.Variationofthe  
Zoom Off  
: Select  
: Change  
levels includes image reduc-  
tion.  
Note:  
Picture Signal Selection is only  
available for connecting with a 21 pin  
Scart Cable.  
Depending on your TV, NTSC disc  
may not playback correctly in colour. In  
this case, it is recommended to select  
the Picture Signal RGB on step 2.  
Only use RGB setting if your TV is  
RGB compatible.  
Press  
/
or  
/
to view a different part of the frame.  
2 You may move the frame from the centre position to UP,  
DOWN, LEFT or RIGHT direction.  
If you select EXITand press the OK, you can turn off the  
symbol mark, keeping the current magnification level.  
Press CANCEL to restore the zoom point to the centre  
of the picture.  
While ZOOMis selected, press ZOOM repeatedly to re-  
turn to a 1:1 view.  
3
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Repeat playback  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.  
Then press DVD to select the DVD mode. (The DVD indicator  
will light)  
REPEAT PLAYBACK  
Press PLAY MODE repeatedly to select Chapter Repeat,  
1 Title Repeator All Repeat. (In case of CD, select Track  
Repeator All Repeat)  
DVD  
CD  
Chapter Repeat  
Track Repeat  
During playback repeat playback will start automatically.  
2
To start repeat playback during stop mode, press  
about 5 seconds after you press PLAY MODE.  
To resume normal playback, press PLAY MODE repeatedly  
until Offappears on the TV-screen.  
within  
A-B Repeat Playback  
A-B repeat playback allows you to repeat material between two  
selected points.  
Press REPEAT A-B during  
playback.  
The start point is selected.  
1
A
-
Press REPEAT A-B again.  
2
The end point is selected.  
Playback starts at the point that  
you selected. Playback stops at  
the end point, returns to Point A  
automatically, then starts again.  
A
-B  
To resume normal playback,  
press REPEAT A-B again.  
Repeat Offappears on the screen.  
NOTES:  
Some discs may not work with the  
repeat operation.  
In A-B repeat mode, subtitles near  
point A or B may not appear.  
During the A-B Repeat Playback the  
ANGLE feature will not operate.  
You may not be able to set A-B Re-  
peat, depending on the scenes of the  
DVD.  
A-B repeat does not work with an in-  
teractive DVD and MP3-CD.  
Random playback can not be com-  
bined with Repeat playback.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memory playback/Random playback  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Memory playback  
You can arrange the order of titles, chapter or tracks on the disc.  
Press MEMORY.  
In stop mode  
In playback  
1
2
1
2
3
4
5
6
7
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
1
T:-- CT:---  
Memory  
Memory  
: Select 0-9 : Input  
: Play  
: Select 0-9 : Input  
: Play  
Press  
/
to  
In stop mode  
In playback  
select TTitle  
number or CT”  
Chapter or Track  
number. Use  
numbe keys to  
Input the favorite  
number.  
1
2
3
4
5
6
7
T:01 CT:002  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
1
T:01 CT:002  
Memory  
Memory  
: Select 0-9 : Input  
: Play  
: Select 0-9 : Input  
: Play  
If you input a large number than the number that is recorded  
on the disc, the bar will be skipped.  
The input number into "T" for CD or MP3 is not effective.  
Press or OK.  
Set the Tand  
CTin the next  
bar as In step 2.  
In stop mode  
In playback  
3
4
1
2
3
4
5
6
7
T:01 CT:002  
T:02 CT:004  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
T:-- CT:---  
2
T:02 CT:004  
Memory  
Memory  
: Select 0-9 : Input  
: Play  
: Select 0-9 : Input  
: Play  
When you select another chapter In the same title, you do  
not need to select the title number.  
To cancel the programmed selection, press CANCEL.  
Press  
to start MEMORY playback.  
To resume normal playback, press CANCEL.  
Random playback  
Press PLAY MODE repeatedly to select Chapter Random”  
or Title Random.(In case of CD, select Track Random)  
1
NOTES:  
The memory playback is cancelled  
DVD  
CD  
when press  
playback.  
3
during memory  
Random playback can not be  
combined with Repeat playback.  
You can program up to 30 selections  
into the memory.  
Chapter Random  
Track Random  
Depending on the DVD, Chapter  
Random operation may not work  
during playback.  
You cannot use the random playback  
with memory playback.  
During playback random playback will start automatically.  
2
To start random playback during stop mode, press  
about 5 seconds after you press the PLAY MODE.  
To resume normal playback, press PLAY MODE repeatedly  
until Offappears on the TV-screen.  
within  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MP3 Playback  
This player can play back the MP3-data  
which has been recorded on CD-R or CD-  
RW. To produce the MP3-data, you need a  
Windows-PCwithCD-ROMdriveandaMP3-  
encoding Software (not supplied).  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.  
Then press DVD to select the DVD mode. (The DVD indicator  
will light)  
The Apple-HFS-System can not be played.  
Press OPEN/CLOSE.  
1
The disc tray will open.  
Place a disc onto the tray.  
MP3 CD Information  
Limitations on MP3 CD playback  
MP3 CD is the disc that is standardized by  
ISO9660, its file name must include 3-digits  
extension letters, mp3.  
The directory and file names of the MP3  
CD must correspond to the ISO  
Press  
or OPEN/CLOSE. The  
disc tray closes automatically. On  
the TV-screen, “ ” and then  
2
3
T
11  
reading file number will appear.  
Then playback will commence.  
Reading will take as much time  
as the number of file.  
standardized files.  
This unit can read 200 files per disc. If  
one directory has more than 200 files, it  
reads up to 200 files, the remaining files will  
be omitted.  
As for multi-session disc, only the first  
session can be played.  
If the CD has both audio tracks and MP3  
files, only audio tracks are played.  
It may take more than one minute for this  
unit to read MP3 files depending on its  
structure.  
Press 3 to end playback.  
Press OSD.  
MP3  
T
1
000:23  
Then press  
/
to select  
MP3  
and press OK (Enter).  
PCM  
: Select  
: Enter  
Music recorded by Joliet Recording  
Specificationcan be played back, the file  
name is displayed (within 8 letters) on the  
screen. Long file names will be condensed.  
The music files recorded by Hierarchical  
File System(HFS) cannot be played.  
Press  
/
or  
/
to select the desired track, then press  
4 OK (Enter). Track is selected and play commences.  
In case the folder includes more than 9 tracks, press  
to display next track list.  
/
To remove track list, press CANCEL.  
Press to select Tand press number keys to  
input your desired track.  
Limitations on display  
/
The maximum number for display is 8  
letters. Available letters for display are the  
following: capital or small alphabets of A  
through Z, numbers of 0 through 9, and _  
(under score).  
MP3  
T
1
000:23  
~
1. \ CRYINI  
2. \ DANGER  
1
~
1
3. \ GITARREN  
~
4. \ LILYWA  
1
~
PCM  
5. \ MERCYS  
1
~
~
6. \ OBSESS  
1
1
1
7. \ PINKPA  
~
8. \ RUNNIN  
Notes on MP3 files  
: Select  
: Search  
To play back MP3 CD in the recorded order,  
1. Use MP3 software that records data  
alphabetically or numerically.  
2. Name each file including a two-digit or three-  
digit number (e.g. 01” “02or 001” “002).  
3. Refrain from making too many sub-folders.  
Press 3 to end playback.  
The unit records the stopped track.  
5
6
Press  
track).  
to resume playback (from the beginning of  
If you press 3 again or unload the disc, the unit will clear  
the stopped track.  
CAUTION:  
Some MP3 CDs can not be played back  
depending on the recording conditions.  
The CD-R/RW that has no music data or  
non-MP3 files can not be played back.  
Press OPEN/CLOSE.  
The disc tray opens.  
Remove the disc and press  
The disc tray closes automatically and DVD/VCR turns off.  
.
NOTES:  
During MP3-Playback, you can not use SEARCH, A-B  
Repeat functions.  
You can use Repeat(Track or All) and Random functions for  
MP3 CD Playback.(See page 41 and 42)  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing soundtrack language / Changing Subtitles language  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Changing soundtrack language  
You can select the language when you play a multilingual disc.  
Press A.MONITOR during play-  
back.  
Thecurrentsoundtracklanguage  
is displayed.  
1
ENG1  
ENG2  
FRE1  
2CH  
5.1CH  
2CH  
Audio:FRE1  
: Select  
2CH  
: Return  
2CH  
Press A.MONITOR repeatedly  
2 until the desired language is se-  
ENG1  
ENG2  
FRE1  
2CH  
5.1CH  
2CH  
lected.  
The on-screen display will disap-  
pear after a few seconds.  
To turn off the soundtrack  
setting display, press the  
CANCEL or OK button.  
Audio:ENG1  
: Select  
2CH  
2CH  
: Return  
In case of VIDEO CD playback  
AudiotypechangesasfollowseachtimeyoupressA.MONITOR.  
NOTES:  
If the desired language is not heard after  
pressing A.MONITOR several times, the  
language is not recorded on the disc.  
Changing soundtrack or subtitle  
language is cancelled when you open the  
disc tray or turn the power off. The initial  
default language or available language  
will be heard and seen if the disc is  
played back again.  
Changing Subtitles language  
You can select the language when playing back a disc recorded  
with multi-lingual subtitles.  
Press SUB TITLE during  
playback.  
1
Off  
GER 1  
Then press  
/
to select the  
DUT  
SV  
NO  
1
1
1
Depending on the DVD you may be  
unable to turn on, turn off, or change the  
subtitles, even if they are recorded on the  
disc. While playing the DVD, the subtitle  
may change while opening or closing the  
disc tray, or while changing the title.  
desired language.  
To turn off the subtitle setting  
display, press the CANCEL  
or OK button.  
Subtitle:--- Off  
: Select  
: Return  
To turn the subtitles off, select  
Off.  
During some scenes, the subtitles may not  
appear immediately after you select On.  
Press SUB TITLE repeatedly to  
turn Subtitles on or off.  
2
The abbreviation of the language  
appears instead of the language name.  
Refer to the list of languages and their  
abbreviations. (See on page 57.)  
Off  
ENG 1  
SPA 1  
FRE 1  
Subtitle:ENG1 On  
: Select  
: On/Off  
: Return  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing angles / Title selection / DVD menu  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Changing Angles  
When playing back a disc recorded with multi-angle facility, you  
can change the angle that you are viewing the scene from.  
Press ANGLE during playback.  
1
The current angle will appear.  
1
2
3
Angle :1  
: Select  
: Return  
Press ANGLE or  
selected.  
To turn off the angle number display, press the CANCEL.  
You can change the camera angle directly by pressing the  
number keys corresponding to its angle number instead of  
/
repeatedly until the desired angle is  
2
using the  
/
buttons.  
Title Selection  
Two or more titles are recorded on some discs. If the title menu  
is recorded on the disc, you can select the desired title.  
Press TITLE during playback.  
Title menu appears on the screen.  
Press TITLE again to resume playback at the scene  
when you pressed TITLE.  
1
Press  
/
or  
/
to select the desired title.  
2
3
Press OK or  
The playback of the selected title will start.  
.
DVD Menu  
Some DVDs allow you to select the disc contents using the  
menu.  
When you play back these DVDs, you can select the subtitle  
language and sound-track language,etc. using the DVD menu.  
Press DVD MENU during playback.  
The DVD menu appears on the screen.  
1
NOTE:  
Press DVD MENU again to resume playback at  
the scene when you pressed DVD MENU.  
Depending on the DVD, you may not  
be able to change the angles even if  
multi-angles are recorded on the disc,  
or you may be unable to select the title,  
and a title menumay simply be called  
a menuor titlein the instructions  
supplied with the disc.  
Press  
/
or  
/
to select the desired item.  
2
3
Press OK.  
The menu continues to another screen. Repeat steps 2 and 3 to  
set the item completely.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parental control  
Somediscsarespecifiednotsuitable  
for children. Such discs can be  
prevented from play back with the  
unit.  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Parental control setting  
PressSET UP MENU in the stop  
1
mode.  
Picture  
Press or to select Opera-  
TV Shape 4:3LB  
Video Out Select  
tion.  
: Select  
: Enter  
Press  
or  
to select  
2
3
Parental Lock, then press OK.  
Operation  
Pause/Still  
Auto Off  
Parental Lock  
Title Stop  
PBC  
Off On  
Off  
On  
: Select  
: Enter  
Press  
or  
to select Off or On.  
Off: The parental lock feature  
does not function.  
Operation  
Pause/Still  
Parental Lock  
Title Stop  
PBC  
Auto Off  
Off On  
Off  
After pressing OK (Enter),  
follow step 4 and 6 below.  
On: To activate the parental lock  
feature or change the  
setting, press OK (Enter)  
and follow steps 4-6 below.  
On  
: Select  
: Enter  
Press number keys to input a  
4-digits security code then  
press OK.  
If you input a wrong number,  
press CANCEL.  
4
5
Operation  
Pause/Still  
Parental Lock  
Title Stop  
Auto Off  
Off On  
Off  
On  
Security Code ----  
PBC  
To return to the before step,  
press RETURN.  
: Select  
: Enter  
NOTES:  
Enter the code of a country/area  
whose standards were used to  
rate the DVD disc. (See the list  
on the page 47)  
If each setup (page 46~55) has been  
completed, the unit can always be  
worked under the same conditions  
(especially with DVD discs).  
Each setup will be retained in the  
memory if you turn the power off.  
Depending on the discs, the unit can-  
not limit playback.  
Some discs may not be encoded with  
specific rating level information though  
its disc jacket says "adult". For those  
discs, the age restriction will not work.  
Do not forget the security code. If you  
forget the security code, delete it. (See  
step 7 on next page)  
Operation  
Pause/Still  
Parental Lock  
Title Stop  
Auto Off  
Off On  
Off Area Code  
D E  
PBC  
On  
Example: Set to GB (UNITED  
KINGDOM).  
: Select  
: Enter  
Press  
press  
or  
to select Gthen  
to move to the right  
character. Then select Bsame  
as above. Then press OK (En-  
ter).  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parental control  
Country/Area  
AUSTRALIA  
BELGIUM  
CANADA  
Code  
AU  
BE  
CA  
CN  
HK  
DK  
FI  
Country/Area  
NETHERLANDS  
NORWAY  
PHILIPPINES  
RUSSIAN FEDERATION  
SINGAPORE  
SPAIN  
Code  
NL  
NO  
PH  
RU  
SG  
ES  
CHINA  
CHINA HONG KONG  
DENMARK  
FINLAND  
SWEDEN  
SE  
FRANCE  
FR  
DE  
ID  
IT  
JP  
SWITZERLAND  
TAIWAN  
THAILAND  
UNITED KINGDOM  
UNITED STATES  
CH  
TW  
TH  
GB  
US  
GERMANY  
INDONESIA  
ITALY  
JAPAN  
MALAYSIA  
MY  
Press  
/
to select the paren-  
6
tal lock level, then press OK (En-  
ter).  
Operation  
Pause/Still  
Parental Lock  
Title Stop  
Auto Off  
Off On  
Off Area Code  
D E  
PBC  
On Level  
7
: Select  
: Enter  
You cannot play DVD discs rated higher than the level you selected  
unless you cancel the parental lock function.  
For example, when you select level 7, discs rated higher than level  
7 are locked out and cannot be played.  
Level 1: DVD software for adults cannot be played back.  
Level 8: All DVD software can be played back.  
Select from the level 1 to level 8. The limitation will be more severe  
as the level number is lower.  
To make the SETUP screen disappear, press SET UP MENU.  
7
To change the parental lock level  
Follow steps 1- 6.  
To change your 4-digit security code  
1) After selecting Onor Offat step 3 press 3 four times, then  
press OK (Enter).  
The 4-digit security code is deleted.  
2) Press number keys to create a new 4-digit security code at step 4.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting menu language  
You can select the language of the  
disc menu messages of DVDs.  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Press SET UP MENU in the stop  
mode.  
1
Picture  
TV Shape 4:3LB  
Press  
or  
to select Lan-  
Video Out Select Video  
guage.  
: Select  
: Enter  
Press  
Menu Language.  
or  
to select Disc  
2
3
Language  
On-Screen Language ENG  
Disc Menu Language ENG  
Audio Language  
Subtitle Language  
ENG  
ENG  
: Select  
: Enter  
Press OK (ENTER).  
Press  
desiredlanguage,thenpressOK  
or  
to select your  
Language  
On-Screen Language ENG English  
Disc Menu Language EN French  
(ENTER).  
Audio Language  
ENG German  
ENG Others  
Subtitle Language  
Code E N  
: Select  
: Enter  
English, French, German  
The selected language is the first-priority Menu language.  
Others: Other languages can be selected (See the Table of  
languages on page 57).  
Example:  
Set to EN (ENGLISH).  
Press  
or  
to select Ethen press  
to move to  
the right character. Then select Nsame as above.  
Then press OK (ENTER).  
To make the SETUP screen disappear, press SET UP MENU.  
4
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting audio soundtrack language  
Thesameaudiosoundtracklanguage  
Preparation:  
can always be selected by your unit  
even if you replace the disc or turn  
the power off.  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Press SET UP MENU in the stop  
mode.  
1
Picture  
TV Shape 4:3LB  
Press  
or  
to select  
Video Out Select Video  
Language.  
: Select  
: Enter  
Press  
Language.  
or  
to select Audio  
2
3
Language  
On-Screen Language ENG  
Disc Menu Language ENG  
Audio Language  
Subtitle Language  
ENG  
ENG  
: Select  
: Enter  
Press OK (Enter).  
Press or to select your  
desired Audio Language, then  
C
Language  
On-Screen Language ENG English  
Disc Menu Language ENG French  
press OK (Enter).  
Audio Language  
EN German  
ENG Others  
Subtitle Language  
Code E N  
: Select  
: Enter  
English, French, German  
The language you have selected will play if it is recorded on  
the disc.  
Others: If you want to select another language, enter the lan-  
guage code (See the Table of languages on page 57).  
Example:  
Set to EN (ENGLISH).  
Press  
or  
to select Ethen press  
to move to  
the right character. Then select Nsame as above.  
Then press OK (Enter).  
To make the SETUP screen disappear, press SET UP MENU.  
4
NOTES:  
If the selected language is not re-  
corded on the disc, the original lan-  
guage will be heard.  
Some DVD discs may be played in a  
different language than you selected.  
A prior language may be programmed  
on the disc.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting subtitle language  
The same subtitle language can  
always be selected even if you replace  
the disc or turn the power off.  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Press SET UP MENU in the stop  
mode.  
1
Picture  
TV Shape 4:3LB  
Press  
or  
to select  
Video Out Select Video  
Language.  
: Select  
: Enter  
Press  
Language.  
or  
to select Subtitle  
2
3
Language  
On-Screen Language ENG  
Disc Menu Language ENG  
Audio Language  
Subtitle Language  
ENG  
ENG  
: Select  
: Enter  
Press OK (Enter).  
Press or to select your  
desiredlanguage,thenpressOK  
Language  
English  
On-Screen Language ENG French  
Disc Menu Language ENG German  
Audio Language  
Subtitle Language  
ENG No Subtitle  
(Enter).  
EN  
Others  
Code E N  
: Select  
: Enter  
English, French, German  
The subtitle is displayed with the selected language if it is  
recorded on the disc.  
No Subtitle:  
Subtitles do not appear.  
Others: If you want to select another language, enter the  
language code (See the Table of languages on  
page 57).  
Example:Set to EN (ENGLISH).  
Press  
or  
to select Ethen press  
to move to  
the right character. Then select Nsame as above.  
Then press OK (Enter).  
NOTES:  
To make the SETUP screen disappear, press SET UP MENU.  
4
If the selected language is not recorded  
on the disc, the first-priority language is  
selected.  
Some DVD discs may be set to display  
subtitles in a different language than you  
selected. A prior subtitle language may  
be programmed on the disc.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the aspect ratio of TV screen / Setting on Screen display  
You can select the aspect ratio for  
your TV.  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Setting the aspect ratio of TV screen  
Press SET UP MENU in the stop  
mode.  
1
Picture  
TV Shape 4:3LB  
Press  
or to select  
Video Out Select Video  
Picture, then press  
to select TV shape.  
or  
: Select  
: Enter  
Press OK (Enter).  
2 Press  
or  
to select your  
Picture  
TV Shape 4:3LB  
4:3 Letterbox  
4:3 Normal  
desired screen type.  
Video Out Select Video  
16:9 Widescreen  
: Select  
: Enter  
You have the following screen sizes to choose from:  
4:3 Letterbox:  
Select when a standard 4:3 TV is connected.  
Displays theatrical images with masking bars above and below  
the picture.  
4:3 Normal:  
Select when a standard 4:3 TV is connected.  
Displays pictures cropped to fill your TV screen. Either or both  
sides of the picture are cut off.  
16:9 Widescreen:  
Select this mode when connecting to a wide-screen TV.  
A wide screen picture is displayed full size.  
To make the SETUP screen disappear, press SET UP MENU.  
3
Setting on Screen display  
Press SET UP MENU in the stop  
mode.  
NOTES:  
1
The displayable picture size is preset on  
the DVD video disc. Therefore, the  
playback picture of some DVD video  
discs may not conform to the picture size  
you select.  
When you play DVD video discs re-  
corded in the 4:3 picture size only, the  
playback picture always appears in the  
4:3 picture size regardless of the TV  
shape setting.  
Display  
On-Screen Displays On  
Press  
or  
or  
to select Display”  
to select On-  
Background  
Screen Saver  
Picture  
On  
Press  
2 Screen Displays.  
: Select  
: Enter  
Press OK (Enter).  
3
Press  
or  
to select Onor  
Display  
On-Screen Displays Off  
Off.  
Off  
Background  
Screen Saver  
Picture On  
On  
If you select 16:9 widescreenand you  
own a 4:3 TV set, the DVD playback  
picture will be horizontally distorted dur-  
ing playback. Images will appear to be  
horizontally compressed. Always be  
sure that your TV shape conforms to the  
actual TV in use.  
On: Operational modes (e.g.  
“ ”, “ ”) appear when you  
press the buttons (factory  
setting).  
: Select  
: Enter  
Off: Operational modes (e.g. “ ”, “ ”) do not appear when  
you press any buttons.  
To make the SETUP screen disappear, press SET UP MENU. 51  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Audio  
Preparation:  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Audio Out Select  
Select the output sound format corresponding to your system connection.  
For details of sound recording systems, see on page 55.  
Press SET UP MENU in the stop mode.  
1 Press  
or  
to select Audio.  
Audio  
Audio Out Select  
Dynamic Range Control On  
Karaoke Vocal  
Bitstream  
Bitstream  
Analog 2ch  
PCM  
On  
Press  
or  
to select Audio Out  
2 Select, then press OK (Enter). Press  
or  
to select your desired output  
: Select  
: Enter  
sound.  
Bitstream:  
Select when connected to an amplifier equipped with a Dolby  
Digital, DTS, MPEG1 or MPEG2 decoder. The DVD/VCR outputs  
digital audio information in the bitstream format when you play a  
DVD video disc recorded on the Dolby Digital, DTS, MPEG1 or  
MPEG2 recording system.  
Analog 2ch: SelectwhenconnectedtoaTV, DolbyProLogicorstereosystem  
via the analog audio jacks.  
PCM:  
Select when connected to a 2 channel digital stereo amplifier.  
The DVD/VCR outputs sounds in the PCM 2ch format when you  
play a DVD video disc recorded on the Dolby Digital. MPEG1 or  
MPEG2 recording system.  
3 To make the SETUP screen disappear, press SET UP MENU.  
Dynamic Range Control  
Turn on or off a function that makes faint sounds easier to hear  
even if you lower the volume during late hours playback.  
Press SET UP MENU in the stop  
1 mode.  
Audio  
Audio Out Select  
Dynamic Range Control On  
Karaoke Vocal  
Bitstream  
Off  
On  
Press  
or  
or  
to select Audio.  
to select Dynamic  
Off  
Press  
2 Range Control, then press OK (Enter).  
: Select  
: Enter  
Press  
or  
to select Onor Off.  
Off: Fulldynamicrangeismaintained.  
On: Dynamic range is reduced.  
To make the SETUP screen disappear,  
3 press SET UP MENU.  
NOTES:  
The Dynamic Range Control function  
works only during playback of Dolby  
Digital recorded discs.  
Karaoke Vocal  
Turn on or off the vocal output during DVD KARAOKE disc  
playback.  
The level of Dynamic Range Control  
may differ depending on the DVD video  
disc.  
The vocal output feature is used during  
playback of Dolby Digital (multi-channel)  
recorded DVD KARAOKE discs. This  
feature allows you to turn off vocal audio  
tracks, or restore them for background  
accompaniment.  
PressSETUPMENUinthestopmode.  
1
Audio  
Audio Out Select  
Dynamic Range Control On  
Karaoke Vocal  
Press  
or  
to select Audio.  
Bitstream  
Off  
On  
Off  
Press  
or  
to select Karaoke  
2
Vocal, then press OK (Enter).  
Press or to select Onor Off.  
: Select  
: Enter  
Off: The primary vocal is not output.  
On: Theprimaryvocalisoutputwhen  
it is recorded on the disc.  
When playing KARAOKE, connect the  
appropriate audio equipment such as an  
amplifier to the DVD player.  
To make the SETUP screen disappear, press SET UP MENU.  
3
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Operation  
Preparation:  
PBC  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to  
VCR/DVD. Then press DVD to select the DVD mode.  
(The DVD indicator will light)  
Press SET UP  
1
MENU in the stop  
Picture  
mode.  
TV Shape 4:3LB  
Video Out Select Video  
Press  
or to  
Pause/Still  
Select the resolution of still pictures.  
select Operation.  
: Select  
: Enter  
PressSETUPMENU  
in the stop mode.  
1
Picture  
TV Shape 4:3LB  
Video Out Select Video  
Press  
(Enter).  
or  
or  
to select PBC, then press OK  
to select Onor Off, then press  
Press or  
to  
2
select Operation.  
Press  
OK (Enter).  
: Select  
: Enter  
Press  
select Pause/Still,  
then press OK  
or  
to  
2
Operation  
Pause/Still  
Parental Lock  
Title Stop  
PBC  
Auto  
Off  
Off  
Off  
On  
Operation  
Pause/Still  
Parental Lock  
Title Stop  
PBC  
Auto  
Off  
Off  
Auto  
Frame  
On  
(Enter). Press  
or  
On  
to select Auto”  
or Frame, then  
press OK (Enter).  
: Select  
: Enter  
: Select  
: Enter  
Off: When playing a VIDEO CD without using  
the menu.  
On: To use the menu when playing a PBC-  
featured VIDEO CD.  
Auto: For normal use. Still and fast motion images  
can be paused.  
Frame:The resolution of still pictures is improved,  
so that you can make a motionless picture  
clearer when you pause it.  
To make the SET UP screen disappear, press SET  
UP MENU.  
3
To make the SETUP screen disappear, press SET UP  
MENU.  
3
Title Stop  
Turn on or off a feature that automatically stops  
playback after a title has been viewed.  
PressSETUPMENU  
in the stop mode.  
1
Picture  
TV Shape 4:3LB  
Video Out Select Video  
Press  
or  
to se-  
lect Operation.  
: Select  
: Enter  
Press or  
to  
2 select Title Stop,  
Operation  
then press OK  
Pause/Still  
Parental Lock  
Title Stop  
PBC  
Auto  
Off  
Off  
Off  
On  
(Enter).  
Press or  
On  
to  
select Onor Off,  
then press OK  
(Enter).  
: Select  
: Enter  
Off: The DVD/VCR continues after playback of  
a title is completed.  
On: The DVD/VCR stops after playback of a title  
is completed.  
To make the SETUP screen disappear,  
3 press SET UP MENU.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the sound enhancement (E.A.M.)/Setting Background/  
Setting Screen Saver  
Setting Background  
Preparation:  
Select the background color or background picture.  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to  
VCR/DVD. Then press DVD to select the DVD mode.  
(The DVD indicator will light)  
PressSETUPMENU  
in the stop mode.  
1
Picture  
TV Shape 4:3LB  
Press  
or  
to se-  
Video Out Select Video  
Selecting the sound enhancement (E.A.M.*)  
You can easily switch a preferred audio enhancement.  
lect Display.  
*E.A.M.: Enhanced Audio Mode  
: Select  
: Enter  
Press OSD twice.  
2
3
-0:21:28  
Press  
select Back-  
ground, then press  
OK (Enter). Press  
or  
to  
1
2
Display  
On-Screen Display On Blue  
Background Picture Gray  
Screen Saver  
On Picture  
Jacket  
or  
to select  
your desired  
background, then  
press OK (Enter).  
Then press B/A to  
select the E.A.M.  
icon, then press OK  
(Enter).  
The sound enhance-  
ment menu appears.  
: Select  
: Enter  
Blue:  
Gray:  
Blue background.  
Gray background.  
Picture: Use the picture which appears when you  
turn on the DVD/VCR as a background.  
Jacket: Use the jacket picture included on some  
discs as a background. If it is not included,  
a gray background will be substituted.  
Select the sound enhancement by pressing / .  
Eachtimeyoupressthebutton,thesoundenhance-  
ment changes.  
2
To make the SETUP screen disappear, press SET  
3 UP MENU.  
Normal:  
Normal sound.  
Setting Screen Saver (DVD only)  
3D:  
To turn the screen saver on or off.  
To obtain expansive virtual surround sound  
effects from just two speakers.  
PressSETUPMENU  
1
Dialogue:  
in the stop mode.  
Picture  
TV Shape 4:3LB  
Video Out Select Video  
To control critical centre channel information  
to make dialogue more intelligible (only  
when playing a DVD video disc recorded on  
the Dolby Digital recording system).  
Press  
or to  
select Display.  
To use this enhancement on sounds output  
from the BITSTREAM/PCM jack, be sure to  
set Audio Out Selectto PCM.(see page 52).  
: Select  
: Enter  
Press  
select Screen  
Saver, then press  
OK (Enter).  
Press or  
select Onor Off,  
then press OK  
(Enter).  
or  
to  
2
To exit the audio enhancement selection Press  
CANCEL.  
Display  
On-Screen Display On  
Background Picture  
Off  
On  
Screen Saver  
On  
Notes:  
to  
Actual effects to sounds may vary depending on the speaker  
system. Make selection according to your preference.  
Actual effects to sounds may vary depending on the disc.  
When the DVD/VCR is connected to an amplifier equipped  
with Dolby Pro Logic Surround, select Normal.  
Otherwise, Dolby Pro Logic Surround may function  
differently than usual.  
: Select  
: Enter  
Off: The screen saver is disengaged.  
On: The screen saver operates in 10  
minutes after you press  
4
.
Selecting Dialoguedisables Dynamic Range Control”  
function (see page 52).  
During MP3 playback, the sound enhancement is not  
effective.  
To make the SETUP screen disappear, press SET  
3 UP MENU.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting initial setup/output sound conversion table  
You can install the initial system  
Preparation:  
setting.  
Turn ON the TV and set to the video input mode.  
Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then  
press DVD to select the DVD mode. (The DVD indicator will light)  
Setting initial setup  
Press SET UP MENU in the stop  
mode.  
1
Picture  
TV Shape 4:3LB  
Video Out Select Video  
Press or  
to select Initial  
Setup.  
: Select  
: Enter  
Press OK, then press  
or  
2
to select On-Screen Language,  
TV Shapeor Audio Out  
Select.  
Initial Setup  
On-Screen Language ENG  
English  
Deutsch
TV Shape  
4:3LB  
Audio Out Select  
Bitstream  
: Select  
: Enter  
On-Screen Language:  
TV Shape:  
Audio Out Select:  
See on page 37.  
See on page 51.  
See on page 52.  
To make the SETUP screen disappear, press SET UP MENU.  
3
Output sound conversion table (sampling frequency/quantization bit)  
You can select the output sound format corresponding to your system connection (see page 52).  
Bitstream  
Analog 2ch  
PCM  
Discs  
Recording system  
Dolby Digital  
DIGITAL AUDIO ANALOG AUDIO DIGITAL AUDIO ANALOG AUDIO DIGITAL AUDIO ANALOG AUDIO  
OUT jack  
OUT jack  
OUT jack  
OUT jack  
OUT jack  
OUT jack  
Bitstream  
48 kHz/20 bit  
Bitstream  
48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit  
48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit  
48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit  
48 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit  
DVD video  
discs  
Linear PCM  
96 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit  
96 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit  
96 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit  
96 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit  
96 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit  
96 kHz/24 bit 48 kHz/16 bit 48 kHz/24 bit  
Bitstream  
Bitstream  
DTS  
Bitstream  
Bitstream  
MPEG1, MPEG2  
Linear PCM 44.1 kHz/16 bit  
DTS  
48 kHz/16 bit  
48 kHz/16 bit  
48 kHz/16 bit  
48 kHz/16 bit  
44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit  
CDs  
Bitstream  
(Noise)  
Bitstream  
(Noise)  
Bitstream  
(Noise)  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Status display of Disc  
You can view information on the operation status and access and settings.  
With each press of OSD, the status of the disc will appear on the screen and change as follows.  
1
Symbol mark of the feature  
Audio/  
mark is only for  
Video CD.  
DVD  
you selected is displayed.  
Video CD  
ZOOM  
T
2
C
3
0:08:16  
T
2
C
3
-0:21:28  
T
1
00:30  
T
1
-03:38  
EAM  
EAM  
EAM  
EAM  
2CH  
ZOOM  
2CH  
ZOOM  
PCM  
PCM  
X
1
X
1
C
C
OFF  
OFF  
BIT  
T
2
C
3
0:08:16  
RATE  
9.2Mbps  
T
2
C
3
T
1
01:14  
T
1
EAM  
EAM  
EAM  
EAM  
----- CD TEXT -----  
Disc Title:  
No Text  
2CH  
ZOOM  
2CH  
ZOOM  
PCM  
PCM  
X
X
Track Title:  
No Text  
1
1
C
C
(Audio CD only)  
Press  
or  
to select the desired symbol mark, then press OK (Enter).  
2
: Title number (Track number)  
: Chapter number  
T
C
Press  
/
or number keys to locate a title or  
Press  
/
or number keys to locate a Chapter,  
track, then press OK (Enter).  
then press OK (Enter).  
: Elapsed (remaining) time of the current title  
Audio setting  
See page 44.  
Press number keys to locate a desired Location,  
then press OK (Enter).  
: Angle setting  
See page 45.  
: Subtitle setting  
See page 44.  
: E.A.M. (Enhanced Audio Mode)  
See page 54.  
ZOOM  
: To zoom a picture  
See page 40.  
: Audio Out Select setting  
BST: Bitstream 2CH:Analog 2ch PCM:PCM  
See page 52.  
: To stop playback  
See page 38.  
: Playback starts from the beginning of the  
current chapter or track.  
See page 39.  
: Fast reverse playback  
See Page 39.  
: To start playback  
See page 38.  
: Fast forward playback  
See page 39.  
: To locate succeeding chapters or tracks.  
See page 39.  
: To begin slow motion playback  
See page 39.  
: To pause playback  
See page 39.  
: To turn off the display  
Data transfer rate (Mbit/s)  
Amount of picture, sound and subtitle data in the DVD  
video disc transferred per second.  
The larger the value is, the more data processed, but  
this does not necessarily insure better picture quality.  
CD TEXT  
Displays CD text data if included on the audio  
CDs. (Some letters may not be displayed  
properly depending on the disc.)  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of languages  
Enter the appropriate code for the initial settings"Menu", "Audio" and/or "Subtitle" (see pages 48~50).  
Abbreviation Language Abbreviation Language Abbreviation Language  
– – –  
No alternate  
language  
Chinese  
Dutch  
English  
French  
German  
ltalian  
Japanese  
Korean  
GN  
GU  
HA  
HI  
HR  
HU  
HY  
IA  
IE  
IK  
IN  
IS  
Guarani  
Gujarati  
Hausa  
Hindi  
Croatian  
Hungarian  
Armenian  
Interlingua  
Interlingue  
Inupiak  
Indonesian  
Icelandic  
Hebrew  
PT  
QU  
RM  
RN  
RO  
RU  
RW  
SA  
SD  
SG  
SH  
SI  
Portuguese  
Quechua  
Rhaeto-Romance  
Kirundi  
Rumanian  
Russian  
Kinyarwanda  
Sanskrit  
Sindhi  
CHI (ZH)  
DUT (NL)  
ENG (EN)  
FRE (FR)  
GER (DE)  
ITA (IT)  
JPN (JA)  
KOR (KO)  
MAY (MS)  
SPA (ES)  
AA  
Sango  
Malay  
Spanish  
Afar  
Serbo-Croatian  
Singhalese  
Slovak  
Slovenian  
Samoan  
Shona  
IW  
JI  
SK  
SL  
AB  
AF  
AM  
AR  
AS  
AY  
AZ  
BA  
BE  
BG  
BH  
BI  
BN  
BO  
BR  
CA  
CO  
CS  
CY  
DA  
DZ  
EL  
EO  
ET  
EU  
FA  
FI  
FJ  
FO  
FY  
GA  
GD  
Abkhazian  
Afrikaans  
Amharic  
Arabic  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Belorussian  
Bulgarian  
Bihari  
Bislama  
Bengali, Bangla  
Tibetan  
Breton  
Catalan  
Corsican  
Czech  
Welsh  
Danish  
Bhutani  
Greek  
Esperanto  
Estonian  
Basque  
Persian  
Finnish  
Fiji  
Faroese  
Frisian  
Yiddish  
JW  
KA  
KK  
KL  
KM  
KN  
KS  
KU  
KY  
LA  
LN  
LO  
LT  
Javanese  
Georgian  
Kazakh  
Greenlandic  
Cambodian  
Kannada  
Kashmiri  
Kurdish  
Kirghiz  
Latin  
Lingala  
Laotian  
Lithuanian  
Latvian, Lettish  
Malagasy  
Maori  
Macedonian  
Malayalam  
Mongolian  
Moldavian  
Marathi  
Maltese  
Burmese  
Nauru  
Nepali  
Norwegian  
Occitan  
SM  
SN  
SO  
SQ  
SR  
SS  
ST  
SU  
SV  
SW  
TA  
TE  
TG  
TH  
TI  
TK  
TL  
TN  
TO  
TR  
TS  
TT  
TW  
UK  
UR  
UZ  
VI  
VO  
WO  
XH  
YO  
ZU  
Somali  
Albanian  
Serbian  
Siswati  
Sesotho  
Sundanese  
Swedish  
Swahili  
Tamil  
Telugu  
Tajik  
Thai  
Tigrinya  
Turkmen  
Tagalog  
Setswana  
Tongan  
Turkish  
Tsonga  
Tatar  
Twi  
Ukrainian  
Urdu  
Uzbek  
Vietnamese  
Volapük  
Wolof  
LV  
MG  
MI  
MK  
ML  
MN  
MO  
MR  
MT  
MY  
NA  
NE  
NO  
OC  
OM  
OR  
PA  
PL  
PS  
(Afan) Oromo  
Oriya  
Panjabi  
Polish  
Pashto, Pushto  
Irish  
Scottish Gaelic  
Galician  
Xhosa  
Yoruba  
Zulu  
GL  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems and troubleshooting  
Use the following check list for troubleshooting when you have problems with your unit. Consult your local  
dealer or service outlet if problems persist.  
Be sure all connections are properly made when using with other units.  
SYMPTOMS  
DVD/VCR  
POSSIBLE SOLUTIONS  
PAGE  
Make sure the power cord is plugged in.  
Try another AC outlet.  
Power is off, check fuse or circuit breaker.  
Unplug unit, then plug it back in.  
DVD/VCR does not operate.  
Select the DVD or VCR mode before operating.  
14,37  
Antenna connection is not correct or antenna cable is disconnected.  
10  
13  
The video channel is not in the correct position or the TV is not  
set to the video channel.  
Check the unit is connected correctly.  
The video input selector of the TV is not set to VIDEO. Set to  
VIDEO (or equivalent).  
10~12  
No picture.  
No sound.  
Channel is set to the external mode.  
Check the unit is connected correctly.  
Check the input selector of the amplifier is set properly.  
The unit is in the Special playback mode.  
10~12  
20,39  
Aim the remote control at the remote sensor.  
Operate within Approx. 5 Meters or reduce the light in the room.  
Clear the path of the beam.  
The batteries are weak. Replace the batteries.  
Check the batteries are inserted correctly.  
Check the frequency code is set correctly.  
The remote control does not  
function.  
9
8
The DVD-keys on the RCU of the  
other JVC RECEIVER/TV is not  
effective.  
This is not a defect. Since this unit is combined type of DVD and  
VCR, the remote code of DVD is individual.  
VCR  
The erase prevention tab of the video cassette is broken off.  
The unit is in the external input mode.  
TV recording does not work.  
18  
The time is not set correctly.  
The recording start/end time is not set correctly.  
The has not been pressed ( is not lit).  
15  
29  
30  
Timer recording does not work.  
Tracking adjustment beyond range of automatic tracking circuit.  
Try Manual tracking adjustment.  
Video heads are dirty.  
20  
Noise bars on screen.  
59  
The tape is worn or damaged.  
DVD  
Display is not shown in your  
language.  
Select proper language in the menu options.  
37  
No disc is inserted.  
The disc may be dirty. Clean up the disc.  
The unit cannot play DVD-ROMs, etc.  
38  
36  
36  
Playback doesnt start.  
Stopping playback, slow-motion  
play, repeat play, or memory play, Some discs may not do some of the functions.  
etc. cannot be performed.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problems and troubleshooting / Video head cleaning  
SYMPTOMS  
No 4:3 (16:9) picture  
No on-screen display  
No surround sound  
POSSIBLE SOLUTIONS  
The setup does not match your TV.  
PAGE  
51  
Select Display On.  
51  
The setup does not match your stereo system.  
12  
The unit or remote operation key  
is not functioning.  
Turn off the unit and unplug the AC power cord for several  
minutes, then replug it.  
14  
46  
Playback does not start when the  
title is selected.  
Check the Parental control setting.  
Audio soundtrack and/or subtitle  
language is not changed when  
you play back a DVD.  
49,50  
Multilingual language is not recorded on the DVD disc.  
Some discs have no subtitles.  
Subtitles are cleared. Press SUB TITLE.  
50  
44  
No subtitle  
Angle cannot be changed.  
appears on the screen.  
Multi-angles are not recorded on the DVD disc.  
The function is prohibited with the unit or the disc.  
45  
Video head cleaning  
Video head clogging  
The video heads are the means by which the DVD/VCR reads  
the picture from the tape during playback. In the unlikely event  
that the heads become dirty enough to be clogged, no pic-  
ture will be played back. This can easily be determined if,  
during playback of a known good tape, there is good sound,  
but no picture (picture is extremely snowy). If this is the case,  
have the DVD/VCR checked by qualified service personnel.  
Good Picture  
Snowy Picture  
NOTES: DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE  
REAR COVER.  
Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.  
To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
GENERAL  
Power supply:  
AC 230-240V 50Hz  
Power consumption:  
Operation: 22W  
Stand by: 5W  
4.5 kg  
Weight:  
Dimensions:  
Width : 430 mm  
Height: 99 mm  
Depth : 310.5 mm  
Input Level:  
SCART-socket:  
VIDEO: 1 Vp-p, 75 Ω  
AUDIO: 500 mV, 50 k Ω  
Audio IN jack: 500 mV, 50 k Ω  
Output Level:  
SCART-socket:  
VIDEO: 1 Vp-p, 75 Ω  
AUDIO: 500 mV, 1 k Ω  
Audio OUT jack: 500 mV, 1 k Ω  
Hi-Fi Frequency Response: 20Hz to 20,000Hz  
Hi-Fi Dynamic Range:  
More than 75dB  
VCR section  
Video Head:  
4 Rotary Heads  
Audio Track:  
Channel covevage:  
RF Channel Output:  
Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track  
2-12, X, Y, Z, Z+1,Z+2, S1-S41, 21-69  
UHF channel 36 (23 to 69)  
F.FWD/REW Time at 25˚C: Approx. 1minute and 48 seconds (with E-180 Cassette Tape)  
DVD section  
Signal system:  
Applicable disc:  
Audio characteristics:  
Frequency response:  
S/N Ratio:  
PAL  
DVD (12cm, 8cm), CD (12cm, 8cm)  
DVD: 4Hz - 22KHz  
CD: 4Hz - 20KHz  
90dB  
Harmonic distortion:  
Wow and flutter:  
Dynamic range:  
Output:  
0.1%  
Below Measurable Level  
90dB  
Audio : (RCA) 500 mV, 1Kohm  
Digital Audio : 0.5Vp-p/75 ohm  
CD : Wavelength: 775 - 805 nm  
Maximum output power: 0.5 mW  
DVD : Wavelength: 640 - 660 nm  
Maximum output power: 1.0 mW  
Pickup:  
ACCESSORIES:  
Remote control x 1  
75 ohm Coaxial Cable x 1  
Battery (AA) x 2  
2A77501B  
02/07  
X
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinity Speaker ERS 110DT User Manual
Insignia Flat Panel Television NS LCD19W 09 User Manual
IOGear Cell Phone GBHFK231 User Manual
Jet Tools Planer 6 HH User Manual
JL Audio Car Stereo System C5 525cw User Manual
JVC Camcorder LYT2197 001A M User Manual
JVC Car Video System KD ADV49 User Manual
JVC Home Theater System RX E111RSL User Manual
Kenmore Dishwasher 6651389 User Manual
Knoll Systems Projector HT200 User Manual