DVD PLAYER/Hi-Fi STEREO
KARAOKE VIDEO CASSETTE PLAYER
HR-XV10AG
INSTRUCTIONS
EN
LPT0777-001C
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions (Cont’d)
CAUTION:
A DVD/VCP IS A CLASS 1 LASER PRODUCT. HOWEVER THIS DVD/VCP USES A VISIBLE
LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED.
THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE DVD/VCP.
CLASS
1
LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS
1
LASER APPARAT
CLASSE 1 PRODUIT LASER
WHEN THIS DVD/VCP IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES
CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE
INSIDE OF THIS DVD/VCP.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALI-
FIED PERSONNEL.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Operation with Audio CD and MP3 Discs. . . . . . . 22
Playing an Audio CD and MP3 Discs . . . . . . . . . 22
ꢀ Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ꢀ Moving to another Track . . . . . . . . . . . . . . . 22
ꢀ Repeat Track/All/Off. . . . . . . . . . . . . . . . . . . 22
ꢀ Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ꢀ Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ꢀ Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 22
ꢀ 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 22
ꢀ Changing the Audio Channel . . . . . . . . . . . . 22
Programmed Playback . . . . . . . . . . . . . . . . . . . . . 23
Programmed Playback with Audio CD
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel and Display Window . . . . . . . . . . . . . . 7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
and MP3 Discs . . . . . . . . . . . . . . . . . . . . . . . . . 23
Programmed Playback with Video CD . . . . . . . . 23
ꢀ Repeat Programmed Tracks . . . . . . . . . . . . 23
ꢀ Erasing a Track from Program List. . . . . . . . 23
ꢀ Erasing the Complete Program List . . . . . . . 23
Additional Operation - VCP part . . . . . . . . . . . . . . 24
On Screen Display. . . . . . . . . . . . . . . . . . . . . . . 24
Tape Counter Memory Stop . . . . . . . . . . . . . . . . 24
Video Doctor (Self-Diagnosis) . . . . . . . . . . . . . . 24
Hi-Fi Stereo Sound System . . . . . . . . . . . . . . . . 24
Additional Operation - DVD part . . . . . . . . . . . . . . 25
Last Condition Memory . . . . . . . . . . . . . . . . . . . 25
Screen Saver. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Video Mode Setting . . . . . . . . . . . . . . . . . . . . . . 25
Notes on MP3 Discs . . . . . . . . . . . . . . . . . . . . . 25
Special Operation - Karaoke function. . . . . . . . . . 26
Before you start karaoke . . . . . . . . . . . . . . . . . . 26
Karaoke sing-along . . . . . . . . . . . . . . . . . . . . . . 26
Grading your singing . . . . . . . . . . . . . . . . . . . . . 26
Special Recording . . . . . . . . . . . . . . . . . . . . . . . . . 27
Copying from DVD to VCP. . . . . . . . . . . . . . . . . 27
Recording from another video player . . . . . . . . . 27
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 11
Connecting to Optional Equipment . . . . . . . . . . . 12
Before Operation - VCP part . . . . . . . . . . . . . . . . . 13
How to using the main menu . . . . . . . . . . . . . . . 13
Before Operation - DVD part . . . . . . . . . . . . . . 14-17
General Explanation. . . . . . . . . . . . . . . . . . . . . . 14
On-Screen Display. . . . . . . . . . . . . . . . . . . . . . . 14
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 15-17
ꢀ Initial Settings General Operation. . . . . . . . . 15
ꢀ Language . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ꢀ Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ꢀ Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ꢀ Others (DRC/Vocal/PBC). . . . . . . . . . . . . . . 16
ꢀ Parental Control. . . . . . . . . . . . . . . . . . . . . . 17
Operation
Operation with tape. . . . . . . . . . . . . . . . . . . . . . . . 18
Playing a tape . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ꢀ CM (Commercial Message) Skip . . . . . . . . . 18
ꢀ OPR (Optimum Picture Response). . . . . . . . 18
Operation with DVD and Video CD . . . . . . . . . . 19-21
Playing a DVD and Video CD. . . . . . . . . . . . . . . 19
General Features. . . . . . . . . . . . . . . . . . . . . . . . 19
ꢀ Moving to another TITLE . . . . . . . . . . . . . . . 19
ꢀ Moving to another CHAPTER/TRACK . . . . . 19
ꢀ Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 19
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 29
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ꢀ
Still Picture and Frame-by-frame playback . . . . . 20
ꢀ Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ꢀ Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ꢀ Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ꢀ Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 20
ꢀ Time Search . . . . . . . . . . . . . . . . . . . . . . . . 20
ꢀ 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 20
ꢀ Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ Marker Search. . . . . . . . . . . . . . . . . . . . . . . 21
Special DVD Features . . . . . . . . . . . . . . . . . . . . 21
ꢀ Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ Camera Angle. . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ Changing the Audio Language. . . . . . . . . . . 21
ꢀ Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Use
Disc-related terms
Title (DVD only)
Playable Discs
The main film content or accompanying feature content
or additional feature content, or music album. Each title
is assigned a title reference number enabling you to
locate it easily.
DVD
(8 cm / 12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles.
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play a CD-R or CD-RW that
contains audio titles or MP3 files.
A title is composed of one or several chapters. Each
chapter is assigned a chapter number, enable you to
locate the chapter you want. Depending on the disc, no
chapters may be recorded.
Notes
– Depending on the conditions of the recording equip-
ment or the CD-R/RW disc itself, some CD-R/RW
discs cannot be played on the unit.
– The unit cannot play the CD-R/RW discs that contain
no data, or contain different kinds of formatted data
other than MP3 and CD-DA data.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregular shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
Track (Video CD and audio CD only)
Sections of a picture or a musical piece on a video CD
or an audio CD. Each track is assigned a track number,
enabling you to locate the track you want.
Scene
On a video CD with PBC (Playback control) functions,
moving pictures and still pictures are divided into sec-
tions called “Scenes”. Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want.
A scene is composed of one or several tracks.
Notes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs
may be intentionally fixed by software manufacturers.
As this unit plays DVDs and Video CDs according to
disc content designed by the software manufacturer,
some playback features of the unit may not be avail-
able, or other functions may be added.
Refer also to the instructions applied with the DVDs and
Video CDs. Some DVDs made for business purposes
may not be played on the unit.
Types of video CDs
There are two types of video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact
with the system via menus, search functions, or other
typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included in
the disc.
Regional code of the DVD player and DVDs
This DVD player is designed and manufactured
for playback of region “2” encoded DVD soft-
ware. The region code on the labels of some DVD discs
indicates which type of player can play those discs. This
unit can play only DVD discs labeled “2” or “ALL”. If you
try to play any other discs, the message “Check Regional
Code” will appear on the TV screen. Some DVD discs
may not have a region code label even though their
playback is prohibited by area limits.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs
allow playback of video pictures as well as sound, but
they are not equipped with PBC.
2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Use (Cont’d)
Precautions
Storing discs
After playing, store the disc in its case.
Handling the unit
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sun-
light, as there may be a considerable temperature
increase inside the car.
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packed at the factory.
Cleaning discs
When setting the unit
Fingerprints and dust on the disc can cause poor pic-
ture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the cen-
ter out.
The picture and sound of a nearby TV or radio may be
distorted during playback. In this case, position the unit
away from the TV or radio, or turn off the unit after
removing the disc.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber of plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Cleaning the unit
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents, such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
About Symbols
About the
symbol display
To obtain a clear picture
The DVD player is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn down, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbol is
applicable only to the disc represented by the symbol.
For details, please contact your nearest dealer.
DVD DVD
Notes on Discs
VCD2.0
VCD1.1
CD
Video CDs with the PBC (playback control)
function.
Handling discs
Video CDs without the PBC (playback control)
function.
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Audio CDs.
MP3 MP3 disc.
Do not stick paper or tape on the disc.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel and Display Window
Tape Eject
PAUSE (
)
Pause playback temporarily/press repeatedly
for frame-by-frame playback.
STOP ( Á )
Stops playback.
Forward Skip/Scan, Fast-Forward (
)
Go to NEXT chapter/track.
Press and hold for two seconds for a fast forward search.
Winds the tape forwards.
PLAY (
)
Starts playback.
DVD OPEN/CLOSE (
)
Opens or closes the disc tray.
Reverse Skip/Scan, Rewind(
)
Go to beginning of current
chapter/track or to PREVIOUS
chapter/track.
Press and hold for two seconds for a fast
reverse search Rewinds the tape.
POWER
Switches the unit to
ON or OFF.
Record
Disc Tray
Insert a disc here.
Tape Compartment
MIC IN 1/2
DVD/VCP Indicator
TRACKING (+/–)
Display window
Shows the current
status of the unit.
Remote Sensor
Point the remote control here.
DVD/VCP Selector
TITLE Indicates current title number
CHP/TRK Indicates current chapter or track number
PROG. Programmed playback active
MP3 MP3 disc inserted
ANGLE active
VCP recording is engaged
Indicates total playing time/elapsed time
Karaoke indicator
The Hi-Fi track of a VHS
tape is playing
Indicates repeat mode
CD Audio CD inserted
DVD
DVD inserted
Cassette-In indicator
VCD Video CD inserted
The VCP Record
Speed is set to SP
or LP (EP)
REC
HI-FI
A
B
PROG. TITLE CHP/TRK
ALL MP3
SP
LP
EP
VCD
DVD
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
DVD/VCP select button
Selects operational mode of remote
control.
OPEN/CLOSE
EJECT
- Open or close the disc tray.
- Tape Eject.
TOP MENU
Access menu of a DVD disc.
SELECT/ENTER/OK
Acknowledge menu selection.
POWER
Switch this unit ON or OFF.
DISPLAY
COUNT
Access the On-Screen Display.
Shows you the counter.
/l
VCP
REC
Record your input sources into tape.
F
G
D
E (left/right/up/down)
TOP MENU
• Forward SKIP/SCAN (
)/
- Select an item in the menu
- Perform the Karaoke Search.
Fast - Forward
- Search forward❖/ go to next
3
SETUP/ MENU
Access or remove setup menu.
chapter or track.
- Winds the tape forwards.
❖ Press and hold button for about
two seconds.
• PLAY (G)
Starts playback.
MENU
TITLE •
Display the title menu of the disc if
available.
PAUSE/STEP ( ) •
Pause playback temporarily / press
repeatedly for frame-by-frame
playback.
STOP ( Á ) •
Stops playback.
0-9 numerical buttons
Select numbered items in a menu.
< <
<<
• Reverse SKIP/SCAN (
)/
. 1
2
Rewind
- Search backward❖ / go to begin-
ning of current chapter or track or
go to previous chapter or track.
- Rewinds the tape.
CLEAR
0000
A. MONITOR
MARKER
SEARCH
❖ Press and hold button for about
A. MONITOR •
Select an audio language (DVD) or
an audio channel (CD).
two seconds.
PROGRAM
Access or remove program menu.
REPEAT A-B
/
SUBTITLE •
Select a subtitle language.
MARKER •
Mark any point during playback.
CLEAR
- Clear a track number on the
program menu or a mark on the
MARKER SEARCH menu.
- Reset tape counter to zero.
SEARCH •
Display MEMORY SEARCH menu.
• REPEAT
- Repeat chapter, track, title, all.
• RANDOM
MIC/ECHO •
To select the MIC/ECHO mode
RETURN •
- Remove the setup menu.
- Displays the menu of a video CD
with PBC.
- Play tracks in random order.
- CM Skip
• ANGLE
Select DVD camera angle if
available
• REPEAT A-B/LP
- Repeat sequence.
- Select the recording speed of the
tape.
KARAOKE
Switch Karaoke on and off.
• ZOOM
Enlarge video image.
* Feature is not available.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control (Cont’d)
Remote Control Operation Range
Remote A/B Code Switching
Point the remote control at the remote sensor and press
the buttons.
ꢀ Distance: About 7 m from the front of the remote
sensor
ꢀ Angle: About 30° in each direction of the front of the
remote sensor
The remote control is capable of controlling two JVC
units independently; one set to respond to the remote
control’s A code control signals and another set to
respond to B code control signals. The remote control is
preset to send A code signals because your unit is initial-
ly set to respond to A code signals. You can easily
change your unit to respond to B code signals.
Remote control battery installation
Press and hold VCP on the remote control for over
2 seconds, press the number key “2” and then
press OK. The remote control now can transmit B
code signals.
Detach the battery cover on the rear of
the remote control, and insert two R03
(size AAA) batteries with
aligned correctly.
1
and
Press and hold PLAY 4 on the unit for more than 5
2 seconds while the unit is turned off. The code cur-
rently set appears on the display window.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
Press any key on the remote control. The unit will
3 now only respond to B code signals.
Notes
– To set the unit back to respond to A code signals,
repeat the same procedure as shown above, but in
step 1, press the number key “1” instead of “2”.
– The code for the unit will be back to respond A code
signals once you disconnect the AC power cord.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
AUDIO OUT (Left/Right)
Connect to an amplifier, receiver or stereo system.
COAXIAL (Digital audio out jack)
Connect to digital (coaxial) audio equipment.
AUDIO OUT L/R (Both DVD and VHS out)
Connect to an amplifier, receiver or stereo system.
AUDIO IN L/R (VHS IN)
Receive the audio signals from an
external source to VCP.
AC Power Cord
Connect to a power
source.
VIDEO IN (VHS IN)
Receive the video signals from an
external source to VCP.
VIDEO OUT (Both DVD and VHS out)
Connect to a TV with video inputs.
COMPONENT VIDEO OUT (Y Pb Pr) (DVD OUT)
Connect to a TV with Y Pb Pr inputs.
VIDEO OUT
Connect to a TV with video inputs.
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
DVD exclusive out connection
ꢀ You can only watch the DVD playback.
Tips
ꢀ Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the unit.
ꢀ Please refer to the manuals of your TV, Stereo
System or other devices as necessary to make the
best connections.
ꢀ For better sound reproduction, connect this unit’s
AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment.
See “Connecting to optional equipment” on page 12.
Connect the VIDEO OUT jack on this unit’s DVD
1
EXCLUSIVE OUT to the video in jack on the TV
using the video cable.
Connect the Left and Right AUDIO OUT jacks of
2 this unit’s DVD EXCLUSIVE OUT to the audio left/
right in jacks on the TV using the audio cables.
Caution
– Make sure this unit is connected directly to the TV.
Set the TV to the correct video input channel.
– Do not connect this unit’s AUDIO OUT jack to the
phono in jack (record deck) of your audio system.
Connecting to a TV
ꢀ Make one of the following connections, depending on
the capabilities of your existing equipment.
ꢀ When using the COMPONENT VIDEO OUT jacks,
set TV’s INPUT to COMPONENT VIDEO.
Basic connection (AV)
Connect the VIDEO OUT jack on this unit’s
1
DVD/VHS OUT to the video in jack on the TV using
the video cable supplied.
Connect the Left and Right AUDIO OUT jacks of
2 this unit’s DVD/VHS OUT to the audio left/right in
jacks on the TV using the supplied audio cables.
®
Component Video (Color Stream )connection
(for DVD)
Connect the COMPONENT VIDEO OUT jacks on
1
the unit to the corresponding in jacks on the TV
using an optional Y Pb Pr cable.
Connect the Left and Right AUDIO OUT jacks of
2 the unit to the audio left/right in jacks on the TV
using the audio cables.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (Cont’d)
Connecting to Optional Equipment
Notes
–
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Surround
– To see the audio format of the current DVD in the On-
Screen Display, press A. MONITOR.
Connect the Left and Right AUDIO OUT jacks on this
unit to the audio left and right in jacks on your amplifier,
receiver or stereo system, using the audio cables.
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/
Video receiver equipped with a multi-channel
decoder (Dolby Digital™, MPEG 2 or DTS)
Connect this unit’s DIGITAL AUDIO OUT jack
1
(COAXIAL) to the corresponding in jack on your
amplifier. Use an optional coaxial audio cable.
You will need to activate this unit’s digital output.
2 (See “Digital Audio Output” on page 16).
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your unit (MPEG 2, Dolby
Digital and DTS). Check the receiver manual and the
logos on the front of the receiver.
Warning:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
Rear of this unit
VHS
IN
DVD/VHS
OUT
DVD EXCLUSIVE OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
DIGITAL
AUDIO OUT
R
AUDIO
L
Pr
R
L
COAXIAL
Pb
VIDEO
Y
VIDEO OUT
2 channel analog stereo or Dolby Surround connection.
DVD exclusive out
Both DVD and
VCR out
Digital multi-channel
connection
R
L
COAXIAL
DIGITAL INPUT
AUDIO INPUT
Amplifier (Receiver)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - VCP part
How to using the main menu
To set the colour system
This VCP can easily be programmed by using the
menus displayed on screen.
The menus are controlled from the Remote
Control Handset.
If streaks appear during playback, set colour system
manually to conform to the system that the tape was
recorded in. (Normally set the switch to AUTO.)
Switch on your TV set and video player by pressing
1
2
1.
If your tape was Set colour
If your TV is
recorded in
system to
Press VCP.
PAL
PAL
NTSC3.58
NTSC-PB
NTSC4.43
NTSC-PB
MESECAM
MULTI-SYSTEM TV
PAL TV
Press MENU.
NTSC3.58
3 The main menu will appear on the TV screen.
MULTI-SYSTEM TV
PAL TV
NTSC4.43
MESECAM
MULTI-SYSTEM TV
VCR
A B
C
DR OSD
OPR
O
F.OSD ON/OFF - To switch the display of opera-
tional mode of your VCP ON or
OFF (see p 24).
O
O
O
OPR - To improve the playback picture
(see p 18).
DR - To check a problem with your VCP
(see p 24).
ABC OSD - To change the language setting for
OSD.
You can select the language
between English and Russian.
KARAOKE - To switch on or off Karaoke &
Karaoke Search (see p 26).
SCORE - To display the score your song when
you Karaoke (see p 26).
O
O
O
SYSTEM - Select the colour system used for
playback and recording.
The system is changed as shown
below. (Refer to the right for more
information.)
If you want to record NTSC signals,
press OK and select between
NTSC 3.58 and NTSC 4.43.
*
Source
PAL/
MESECAM
Mode
System Change
→
→
Recording AUTO
PAL MESECAM
→
→
Playback AUTO
PAL MESECAM
→
*
→
Recording NTSC3.58
Playback NTSC-PB
NTSC4.43
NTSC3.58
NTSC
→
NTSC4.43
Press 1 and 2 to select the option to change,
4 then Press OK to change the setting and
press 1 and 2 to select the sub menu.
Press MENU to remove the menu screen.
5
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD part
General Explanation
This manual gives the basic instructions for operating
this unit. Some DVDs require specific operation or allow
only limited operation during playback. When this
Temporary Feedback Field Icons
TITLE
Repeat Title
CHAPT
Repeat Chapter
TRACK
Repeat Track (non-PBC Video CDs only)
occurs, the symbol
appears on the TV screen,
ALL
Repeat All Tracks (non-PBC Video CDs only)
indicating that the operation is not permitted by this unit
or is not available on the disc.
A
B
Repeat A-B
OFF
Repeat Off
On-Screen Display
The general playback status can be displayed on the
Resume play from this point
Action prohibited or not available
TV screen. Some items can be changed on the menu.
On-screen display operation
Notes
– Some discs may not provide all of the below On-
Screen Display.
Press DISPLAY during playback.
1
– If no button is pressed for 10 seconds, the On-Screen
Display disappears.
Press 3 or 4 to select an item.
2 The selected item will be highlighted.
Press 1 or 2 to change the setting of an item.
3 The number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
press OK to execute the setting.
DVD
Items
Function (Press 3
/
4to select desired item)
Selection Method
Title Number
Shows the current title number and total number of
1
/
2
, or
1/3
1/12
titles, and skips to the desired title number.
Numbers, OK
Chapter Number
Time search
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
1
/
2
, or
Numbers, OK
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
0:16:57
Numbers, OK
Audio language
and Digital Audio
Output mode
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
1
ENG
D
1
/
2
5.1 CH
Subtitle language
Shows the current subtitles language, and
OFF
1/1
1
1
/
/
2
2
changes the setting.
Angle
Shows the current angle number and total number of
angles, and changes the angle number.
Sound
Shows the current sound mode, and
changes the setting.
NORM.
1
2
/
VCD1.1
VCD2.0
Items
Function (Press 3
/
4to select desired item)
Selection Method
Track Number
Shows the current track number, total number of tracks
and PBC On mode, and skip to the desired track number.
1
/
2
, or
1/4
Numeric, OK
Time
Shows the elapsed playing time (Display only)
0:16:57
–
Audio Channel
Sound
Shows the audio channel, and
STER.
1
1
/
/
2
2
changes the audio channel.
Shows the current sound mode, and
changes the setting.
NORM.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD part (Cont’d)
Menu Language
Select a language for the setup menu. This is the menu
you see when you press SETUP.
Initial Settings
You can set your own Personal Preferences on this unit.
Initial Settings General Operation
English
Spanish
French
German
Italian
Disc Audio
Disc Subtitle
Disc Menu
Rating
Press SETUP.
1
The setup menu appears.
Country Code
TV Aspect
Original
English
French
Menu Language
Disc Audio
Disc Subtitle
Disc Menu
Digital Audio Output
Others
Rating
German
Spanish
Italian
Country Code
TV Aspect
Menu Language
Chinese
Polish
Digital Audio Output
Others
Hungarian
Russian
Other – – – –
Picture
TV Aspect DVD
4:3 Letterbox: Select when a standard 4:3 TV is con-
nected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a standard 4:3 TV is con-
nected. Displays pictures cropped to fill your TV screen.
Either sides of the picture are cut off.
Press 3/4 to select the desired item.
The screen will show the current setting for the
selected item, as well as alternate setting(s).
2
While the desired item is selected, press 2, then
3 3/4 to select the desired setting.
Press OK to confirm your selection.
16:9 Wide: Select when a 16:9 wide TV is connected.
4
Some items require additional steps.
4:3 Letterbox
4:3 Panscan
16:9 Wide
Disc Audio
Disc Subtitle
Disc Menu
Rating
Press SETUP, RETURN or PLAY 2 to exit the
5 setup menu.
Language
Country Code
TV Aspect
Menu Language
Disc Language DVD
Select a language for the disc’s Menu, Audio and
Subtitle.
Digital Audio Output
Others
Original : The original language set for the disc is
selected.
Other : To select another language, press number but-
tons to enter the corresponding 4-digit number accord-
ing to the language code list on page 29. If you enter
the wrong language code, press CLEAR.
Original
English
Disc Audio
Disc Subtitle
Disc Menu
Rating
French
German
Spanish
Italian
Country Code
TV Aspect
Menu Language
Chinese
Polish
Digital Audio Output
Others
Hungarian
Russian
Other — — — —
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD part (Cont’d)
Sound
Others
Digital Audio Output
The DRC, Vocal, and PBC settings can be changed.
ꢀ Press 3/4 to select the desired item and press OK.
The setting of the selected item is changed between
On and Off.
Each DVD disc has a variety of audio output options.
Set this unit’s Digital Audio Output according to the type
of audio system you use.
DOLBY DIGITAL/PCM: Select “DOLBY DIGITAL/PCM”
if you connected this unit’s DIGITAL OUT jack to a
Dolby Digital decoder (or an amplifier or other equip-
ment with a Dolby Digital decoder).
Stream/PCM: Select “Stream/PCM” if you connected
this unit’s DIGITAL OUT jack to an amplifier or other
equipment with a DTS decoder, Dolby Digital decoder
or MPEG decoder.
DRC Off
Vocal On
PBC On
Disc Audio
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Digital Audio Output
Others
PCM: Select when connected to a 2 channel digital
stereo amplifier. This unit outputs sounds in the PCM
2ch format when you play a DVD video disc recorded
on the Dolby Digital, MPEG1 or MPEG2 recording
system.
Dynamic Range Control (DRC)
With the DVD format, you can hear a program’s sound-
track in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
DOLBY
DIGITAL /PCM
Stream/PCM
PCM
Disc Audio
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Sample Freq.
48 KHz
Menu Language
96KHz
Digital Audio Output
Others
Vocal
Sample Frequency
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into a normal stereo sound.
To change the Sample Frequency setting, first select
the desired Digital Audio Output as indicated as above.
If your receiver or amplifier is NOT capable of handling
96KHz signals, select 48KHz. When this choice is
made, this unit will automatically convert any 96KHz
signals to 48KHz so your system can decode them.
If your receiver or amplifier is capable of handling
96KHz signals, select 96KHz. When this choice is
made, this unit will pass each type of signal through
without any further processing.
PBC
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to the PBC.
Off: Video CDs with PBC are played the same way as Audio
CDs.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD part (Cont’d)
Parental Control
DVD
Country Code
Enter the code of a country/area whose standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 30).
Rating DVD
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are
country-dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
Code Set
I R
Disc Audio
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Digital Audio Output
Others
8
Disc Audio
Disc Subtitle
Disc Menu
Rating
7
Select Country Code using the 3/4buttons on
the setup menu.
6
1
5
Country Code
TV Aspect
4
While Country Code is selected, press 2.
3
Menu Language
2
2
3
4
1
Digital Audio Output
Others
Unlock
Change
Follow step 3 of “Rating” on left.
Select the first character using the 3/4 buttons.
Shift the cursor using 1/2 buttons and select
Select “Rating” on the Setup menu using the 3
and 4 buttons.
1
2
5 the second character using 3/4 buttons.
While “Rating” is selected, press 2.
Press OK to confirm your country code selec-
6 tion, then press SETUP to exit the menu.
When you have not entered a password yet.
3 Enter a 4-digit password using the numbered but-
tons to create a personal 4-digit security password,
then press OK. Enter the 4-digit password again and
press OK to verify.
Note
Confirmation of the 4-digit password is necessary when
the code is changed (See “Changing the 4-digit code”
below).
When you have already entered a password;
Enter a 4-digit password using the numbered but-
tons to confirm the personal 4-digit security pass-
word, then press OK.
Changing the 4-digit code
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old code, then press OK.
3 Select Change using the 3/4 buttons then press
OK.
If you make a mistake before pressing OK, press CLEAR
and enter 4-digit security password again.
Select a rating from 1 to 8 using the 3/4 but-
4 tons. One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
4 Enter the new 4-digit code, then press OK.
5 Enter exactly the same code a second time and veri-
fy by pressing OK.
6 Press SETUP to exit the menu.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the play-
er, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or a
lower one. If no suitable alternative is found, play-
back will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
If you forget your 4-digit code
If you forget your password, to clear the current pass-
word, follow the procedure below.
1 Press SETUP to display the setup menu.
2 Use the Number buttons to enter the 6-digit number
“210499”.
The 4-digit password is cleared.
3
Enter a new code as shown above to the left (Rating).
Press OK to confirm your rating selection, then
5 press SETUP to exit the menu.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with tape
Playing a tape
You will only be able to load and eject video cassettes
when your VCP is plugged into the mains.
Your VCP may also playback recordings from NTSC
tapes (on PAL TV).
Press 8 to end playback.
5 Press
.
If the end of the tape is reached, your VCP will stop
playback automatically, rewind, stop, eject the tape.
CM (Commercial Message) Skip
This feature enables you during playback of a tape to
skip a commercial break in a few seconds, then resume
normal playback.
Getting a better picture
When a cassette is inserted and playback started, the
automatic tracking function works to get the best
possible picture automatically. If the quality of the
recording is poor, repeatedly press 3 or 4 on the
remote control to manually adjust the tracking until
any distortions have been removed. Press numbered
0 on the remote control to switch automatic tracking
back on again.
While tape is playing press
on the remote control to
skip commercial (or another programme material).
Repeatedly press
1 press : 30 seconds
to skip :
2 press : 60 seconds
3 press : 90 seconds
4 press : 120 seconds
5 press : 150 seconds
6 press : 180 seconds
Make sure that you have correctly connected your
1
VCP as described earlier in this book.
Turn on your TV.
Press 1 to turn on your VCP.
Insert the video cassette into your VCP.
The video cassette should have the window side
facing up and the arrow facing away from you.
OPR (Optimum Picture Response)
This feature automatically improves playback picture
quality by adjusting your VCP to the condition of the
tape.
Please note you may only set OPR when playing a
tape.
Press MENU.
Press PLAY 2 to start playing your tape.
2 If you load a video cassette which has had its
record protection tab removed, playback of the
cassette will start automatically.
1
2
3
Press 1 or 2 to select OPR.
AUTO TRACKING
Your VCP will automatically adjust the tracking to
give the best picture quality.
Press OK.
Press ; to still a picture.
3 Press ; repeatedly to advance the tape frame by
frame.
If you hold down
V
f
SOFT
OSD
OFF
, the picture will be slowed
ON
SYS-
TEM
OFF
DSHARP
OPR
OPR
OK
down at about 1/19 times the normal playback.
Tapes can be paused for up to 5 minutes. After 5
minutes your VCP will stop the tape to prevent
damaging the tape or your VCP .
Still picture quality can be improved slightly by
pressing 3 or 4.
i
Press 1 or 2 repeatedly to select: OFF, SOFT or
4 SHARP.
Press OK.
5
6
Press PLAY 2 to continue playing your tape.
4 Picture search:
Press MENU to remove the menus.
During playing back press either
or
to
this will enable you to rapidly wind the tape (7 times
normal playback) see where you are on the tape.
Logic search:
During fast forwarding or rewinding press and hold
or
the picture will be played back at 7
times normal playback speed.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with DVD and Video CD
Playing a DVD and Video CD
General Features
VCD2.0
VCD1.1
Playback Setup DVD
Note
Unless stated otherwise, all operations
described use the remote control. Some
features may also be available on the Setup menu.
ꢀ Turn on the TV and select the video input source
connected to the DVD player.
ꢀ Audio system: Turn on the audio system and select
the input source connected to the DVD player.
Moving to another TITLE DVD
Press
to open the disc tray.
1/3
1
When a disc has more than one title, you can move to
another title as follows:
ꢀ Press DISPLAY when playback is stopped, then
press the appropriate numbered button (0-9) to
select a title number.
Load your chosen disc in the tray, with the label
2 facing up.
When a double-sided DVD is inserted, make sure
the side you want to play is facing up.
Press to close the tray.
3 READING appears on the TV screen, and playback
starts automatically. If playback does not start,
press PLAY 2.
Moving to another CHAPTER/TRACK
1/12
1/3
VCD1.1
DVD
In some cases, the disc menu might appear
instead.
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD or Video CD which contains a menu.
ꢀ Press 2 or 6 briefly during
playback to select the next chapter/track or to return
to the beginning of the current chapter/track.
ꢀ Press 2 twice briefly to step back to the previous
chapter/track.
ꢀ To go directly to any chapter during DVD playback,
press DISPLAY. Then, press 3/4to select C
(chapter) (or for a Video CD, select T for track). Then,
enter the chapter/track number using the numbered
buttons (0-9).
DVD
Use the 1 2 3 4 buttons to select the title/chapter
you want to view, then press OK to start playback.
Press TITLE or TOP MENU to return to the menu
screen.
VCD2.0
ꢀ Use the number buttons to select the track you want
to view.
Note
Press RETURN to return to the menu screen.
ꢀ Menu setting and the exact operating procedures for
using the menu may differ depending on the disc.
Follow the instructions on the each menu screen.
You also may set PBC to Off under setup. See page
16.
For two-digit numbers, press the buttons in rapid
succession.
VCD2.0
VCD1.1
Slow Motion DVD
1 Press 2 or 6 during pause.
The player will enter SLOW mode.
2 Use the 2 or 6 to select the required speed:
Yq1/16, Yq 1/8, Yq 1/4 or Yq 1/2 (backward), or qU
1/16, qU 1/8, qU 1/4 or qU 1/2 (forward).
Notes
– If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit code must
be entered and/or the disc must be authorized (see
“Parental Control”, on page 17).
3 To exit slow motion mode, press PLAY 2.
– DVDs may have a region code.
Note
– Your player will not play discs that have a region code
different from your player. The region code for this
player is 2 (two).
Slow motion playback in reverse is not applicable for
Video CD.
– If you load a video cassette which has had its record
protection tab removed during playing the DVD, the
mode will be switched to VCP automatically.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with DVD and Video CD (Cont’d)
Video CDs - Repeat Track/All/Off
General Features (continued)
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the TV screen.
Still Picture and Frame-by-frame playback
VCD2.0
VCD1.1
DVD
2 To repeat the disc currently playing, press REPEAT a
second time.
The Repeat All icon appears on the TV screen.
1 Press ; during playback.
The player will now go into PAUSE mode.
2 You can advance the picture frame-by-frame by
pressing ; repeatedly on the remote control.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Note
VCD2.0
VCD1.1
Search DVD
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Repeat function. See page 16.
1 Press and hold 2 or 6 for about two seconds
during playback.
The player will now go into SEARCH mode.
2 Press and hold 2 or 6 repeatedly to select the
required speed: 3X2, 3X4, 3X16, 3X100
(backward) or 5X2, 5X4, 5X16, 5X100
(forward).
With a Video CD, the Search speed changes: 3X2,
3X4, 3X8 (backward) or 5X2, 5X4,
5X8 (forward).
VCD2.0
VCD1.1
Repeat A-B DVD
A
*
A
B
OFF
To repeat a sequence in a title:
1 Press REPEAT A-B at your chosen starting point.
A- appears briefly on the TV screen.
2 Press REPEAT A-B again at your chosen end point.
A-B appears briefly on the TV screen, and the repeat sequence
begins (a-b repeat appears on the player’s display).
3 To exit SEARCH mode, press PLAY 2.
3 To cancel the sequence, press REPEAT A-B.
VCD1.1
Random Karaoke DVD
1 Press RANDOM during playback or in stop mode.
The unit automatically begins Random Playback and
“RANDOM” appears on the TV screen.
0:16:57
- : - - : - -
Time Search DVD
The Time Search function allows you to start playing at
any chosen time on the disc.
2 To return to normal playback, press RANDOM again
until “NORMAL” appears on the TV screen.
1 Press DISPLAY during playback. The on-screen dis-
play appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
Tips
By pressing 2 or 6 during Random playback, the
unit selects another title (track) and resumes Random
playback.
2 Within 10 seconds, press 3/4 to select the Time
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
Note
3 Within 10 seconds, use the number buttons to enter
the required start time. Enter hours, minutes, and sec-
onds from left to right in the box.
This function only works with DVD Karaoke discs and
video CD without PBC.
If you enter the wrong numbers, press CLEAR to remove
the numbers you entered. Then enter the correct numbers.
VCD2.0
VCD1.1
Repeat DVD
ALL
TRACK
OFF
CHAPT
TITLE
4 Within 10 seconds, press OK to confirm the start
time.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
VCD2.0
VCD1.1
3D Surround DVD
2 To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
NORM.
3D SUR
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multi-
channel audio from a home theater system.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
1 Press DISPLAY during playback.
2 Press 3/4 to select “NORM.” or “3D SUR”.
3 Press 1/2 repeatedly until the desired sound is
selected.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with DVD and Video CD (Cont’d)
General Features (continued) Special DVD Features
DVD
VCD2.0
VCD1.1
Zoom DVD
Checking the contents of DVD Video
discs: Menus
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
DVDs may contain menus that allow you to access spe-
cial features. To use the disc menu, press TOP MENU.
Then, press the appropriate number button to select an
option. Or, use the 1/2/3/4 buttons to highlight your
selection, then press OK.
1 Press ZOOM during playback or still playback to acti-
vate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to six times.
2 Use the 1 2 3 4 buttons to move through the
zoomed picture.
DVD
Title Menu
3 Press CLEAR to resume normal playback or return to
the paused image.
1 Press TITLE.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
Notes
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
– The zoom function may not work for some DVDs.
– The zoom function may not work on multi-angle
scenes.
3 To remove the title menu, press TITLE again.
VCD2.0
VCD1.1
DVD
Marker Search
DVD
Disc Menu
MARKER SEARCH
1/9
1 Press TOP MENU.
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
The disc menu is displayed.
2 To remove the disc menu, press TOP MENU again.
1 During disc playback, press MARKER when playback
reaches the spot that you want to memorize.
The Marker icon will appear on the TV screen briefly.
1/1
DVD
Camera Angle
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
ꢀ Press ANGLE repeatedly during playback to select a
desired angle.
To Recall a Marked Scene
The number of the current angle appears on the display.
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the
screen.
DVD
Changing the Audio Language
1
ENG
D
2 Within 10 seconds, press 1/2 to select a Marker num-
ber that you want to recall.
5.1 CH
3 Press OK.
Playback will start from the Marked scene.
Press A. MONITOR repeatedly during playback to hear
a different audio language or audio track.
4 To remove the MARKER SEARCH menu, press
SEARCH.
1
ENG
DVD
Subtitles
To clear a Marked Scene
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the
screen.
Note
2 Press 1/2 to select the Marker number that you want
If
appears, the feature is not available on the disc.
to erase.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with Audio CD and MP3 Discs
CD
Playing an Audio CD and MP3 discs
Search
1 Press and hold 2 or 6 for about two seconds
during playback.
The player will now go into SEARCH mode.
The DVD Player can play MP3 formatted recordings on
CD-ROM, CD-R, or CD-RW discs.
Before playing MP3 recordings, read the notes on MP3
Recordings on page 25.
2 Press and hold 2 or 6 repeatedly to select the
required speed: 3X2, 3X4, 3X8 (backward)
or 5X2, 5X4, 5X8 (forward).
Insert a disc and close the tray.
The menu appears on the TV screen.
1
3 Search speed and direction are indicated on the
menu screen.
MP3
Program
CD
Program
TRACK 1.MP3
TRACK 1
TRACK 2.MP3
TRACK 3.MP3
TRACK 4.MP3
TRACK 5.MP3
TRACK 6.MP3
TRACK 7.MP3
TRACK 8.MP3
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
TRACK 8
4 To exit SEARCH mode, press PLAY 2.
Clear All
OFF
Clear All
NORM.
CD
Random
56:35
1
0:56:35
STER.
1 Press RANDOM during playback or when playback is
stopped.
Audio CD menu
MP3 menu
The unit automatically begins Random Playback and
“RAND.” appears on the menu screen.
Press 3/4 to select a track then press PLAY 2.
2 Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display.
2 To return to normal playback, press RANDOM repeat-
edly until “RAND.” disappears on the menu screen.
Playback will stop at the end of the disc.
To stop playback at any other time, press 9.
CD
Repeat A-B
3
To repeat a sequence.
1 During disc playback, press REPEAT A-B at your
chosen starting point.
The Repeat icon and “A -” appears on the menu screen.
CD
MP3
Pause
1 Press ; during playback.
2 Press REPEAT A-B again at your chosen end point.
The Repeat icon and “A B” appears on the menu screen,
and the sequence begins to play repeatedly.
2 To return to playback, press PLAY 2 or press ; again.
CD
MP3
Moving to another Track
3 To exit the sequence and return to normal play, press
REPEAT A-B again.
The Repeat icon and “OFF” appear on the menu screen.
ꢀ Press 2 or 6 briefly during playback to go to the
next track or to return to the beginning of the current
track.
CD
ꢀ Press 2 twice briefly to step back to the previous
track.
3D Surround
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multi-
channel audio from a home theater system.
ꢀ In case of audio CD, to go directly to any track, enter
the track number using the numbered buttons (0-9)
during playback.
CD
MP3
Repeat Track/All/Off
1 Press DISPLAY or A. MONITOR during playback.
2 Press 1/2 to select “NORM.” or “3D SUR”.
3 Press 3/4 repeatedly until the desired sound is
selected.
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
2 To repeat all tracks on a disc, press REPEAT a sec-
ond time.
The Repeat ALL icon appears on the menu screen.
CD
Changing the Audio Channel
3 To cancel Repeat mode, press REPEAT a third time.
The Repeat OFF icon appears on the menu screen.
Press A. MONITOR repeatedly during playback to hear
a different audio channel (STEREO, LEFT, or RIGHT).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
VCD2.0
VCD1.1
Programmed Playback
CD
MP3
Programmed Playback with Audio CD
and MP3 Discs
Programmed Playback with Video CD
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Program function. See page 16.
Program allows you to store your favorite tracks for a
particular disc in the player memory.
Program can contain 32 tracks (Audio CD) or 60 tracks
(MP3 disc).
Insert Video CD and close the tray.
1
2
Insert the disc and close the tray.
Press PROG. while playback is stopped.
The VCD Program menu will appear.
The menu is displayed on the TV screen.
1
Press PROG. during playback or in the stop
2 mode to enter the Program Edit mode.
VCD
Program
E
E
The
mark will appear to the right of the word Program
TRACK 1
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
TRACK 8
on the right side of the menu screen.
Note
Clear All
E
Press PROG. to exit the Program Edit mode; the
mark will disappear.
Press 3/4 to select a track, then press OK to
Note
3 place the selected track on the Program list.
Press RETURN or PROG. to exit the Program menu.
Repeat step 3 to place additional tracks on the
Follow steps 3-7 of “Programmed Playback with
4 Program list.
3 Audio CD and MP3 Disc” on left.
Repeat Programmed Tracks
CD
Program
E
MP3
Program
E
TRACK 1
TRACK 12
TRACK 8
TRACK 10
TRACK 3
TRACK 1.MP3
TRACK 8.MP3
TRACK 2.MP3
TRACK 4.MP3
TRACK 3.MP3
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
TRACK 8
TRACK 2.MP3
TRACK 3.MP3
TRACK 4.MP3
TRACK 5.MP3
TRACK 6.MP3
TRACK 7.MP3
TRACK 8.MP3
ꢀ To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
ꢀ To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat All icon appears on the menu screen.
ꢀ To cancel Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the menu screen.
Clear All
NORM.
Clear All
OFF
0:00:14
STER.
56:35
1
Audio CD menu
MP3 menu
Press 2.
The programmed track you selected last is highlighted on
the program list.
5
Erasing a Track from Program List
1 Press PROG. during playback or in the stop mode to
enter the Program Edit mode.
Press 3/4 to select the track you want to start
6 playing.
Press TITLE to move to the next page.
E
The
mark will appear.
Press TOP MENU to move to the previous page.
2 Press 2 to move to the Program list.
3 Use 3/4 to select the track that you wish to erase
from the Program list.
4 Press CLEAR.
The track will be erased from the Program list.
Press PLAY 2 to start.
Playback begins in the order in which you programmed
the tracks and “PROG.” appears on the display window.
Playback stops after all of the tracks on the Program list
have played once.
7
Erasing the Complete Program List
1 Follow steps 1-2 of “Erasing a Track from Program
List” as above.
2 Use 3/4 to select “Clear All”, then press OK.
The completeProgram for the disc will be erased.
The programs are also cleared whenthe disc is removed.
To resume normal playback
om programmed
f
r
playback
Press and hold PROG. for 3 seconds until “PROG.”
indicator disappears in the display window.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Operation - VCP part
On Screen Display
Video Doctor (Self-Diagnosis)
You may easily display the operating mode, tape speed.
colour system, audio output channel and tape counter
of your VCP on the TV screen. If a recording is taking
place these On Screen Displays will not be recorded
onto the tape.
This feature informs you that there is a problem with
your VCP. These error messages will appear on the TV
screen.
Press MENU.
1
Be sure to set OSD to ON.
Press 1 or 2 to select DR.
Press OK.
Press DISPLAY to display.
1
The tape counter does not appear if there is no
tape loaded.
After 3 seconds the majority of the On Screen
2 Displays will clear leaving only the tape counter on
the screen.
VCR
OK
DR
OK
HEAD STATUS
TAPE STATUS
i
Press DISPLAY again to remove all displays from
the TV screen.
Press 1 or 2 to check a problem.
2 HEAD STATUS
O OK
Tape Counter Memory Stop
O PLEASE CLEAN:
Clean your video heads.
The Digital Tape Counter is displayed on the display win-
dow if there is a tape loaded. The Digital Tape Counter
indicates the relative positions of recordings on the
tape.
Be sure to set OSD to ON.
The counter is automatically reset to 0:00:00 and “M”
appears on the TV screen.
TAPE STATUS
O RECORDABLE
O NOT RECORDABLE:
Insert a tape with its protection tab in place.
Press OK.
3
4
Press MENU to remove menus from the TV screen.
Press DISPLAY.
Press CLEAR to set the counter to 0:00:00.
Press PLAY 2 or start recording.
The tape counter will display the actual play time in
1
Hi-Fi Stereo Sound System
hours, minutes and seconds.
Press A. MONITOR repeatedly until the desired audio
mode appears.
Press 9 when playback or recording is complete.
2 Press 2.
The choice is HI-FI (STEREO), LEFT, RIGHT and
MONO.
The tape will rewind and automatically stop when
the counter returns to 0:00:00.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Operation-DVD part
Last Condition Memory
Notes on MP3 Discs
VCD1.1
DVD
CD
About MP3
This player memorizes the last condition for the last
disc you have watched. Settings remain in memory
even if you remove the disc from the player or switch off
the player. If you load a disc that has its settings memo-
rized, the latest stop position is automatically recalled.
ꢀ
An MP3 file is audio data compressed by using
MPEG1, the audio layer-3 file-coding scheme. We call
files that have the “.mp3” file extension “MP3 files”.
ꢀ The player can not read an MP3 file that has a file
extension other than “.mp3”.
ꢀ The player can not read a fake MP3 file that has a
file extension “.mp3”.
Notes
– Settings are stored in memory for use any time.
– This player does not memorize settings of a disc if
you switch off the player before commencing to play
it.
MP3 Disc compatibility with this player is
limited as follows:
1. Sampling Frequency / only at 44.1kHz
2. Bit rate/ within 32 - 320kbps
3. CD-R physical format should be “ISO 9660”
4. If you record MP3 files using the software which
cannot create a FILE SYSTEM, for example “Direct-
CD” etc., it is impossible to playback MP3 files. We
therefore recommend that you use “Easy-CD
Creator”, which creates an ISO9660 file system.
5. A single session disc requires MP3 files in the first
track. If there is no MP3 file in the 1st track, it can-
not playback MP3 files. If you wish to playback MP3
files, format all the data in the disc or use a new
one.
Screen Saver
The screen saver picture appears when you leave the
DVD Player in stop mode for about five minutes.
VCD2.0
VCD1.1
Video Mode Setting DVD
ꢀ With certain discs, the playback picture may be flick-
ering or Dot Crawl is shown on straight lines. That
means Vertical interpolation or De-interlace is not
perfectly matched with the disc. In this case, the
picture quality may be improved by changing the
video mode.
6. We do not recommend using CD-RW discs. Please
use finished CD-R discs only.
ꢀ To change the video mode, press and hold DISPLAY
about 3 seconds during disc playback. The new video
mode number selected is displayed on the TV screen.
Check whether the video quality has improved. If not,
repeat the above procedure until picture quality is
improved.
7. File names should be named using 8 letters or less
and must incorporate the “.mp3” extension
e.g. “********.MP3”.
8. Do not use special characters such as
“_?!><+*}{`[@ ]:;\/.,” etc.
9. Total number of files on the disc should be less than
200.
10. Use 74 minute CD-R discs (650M), do not use 80
minute CD-R (700M) software.
ꢀ Video mode change sequence:
MODE1 → MODE2 → MODE3 → MODE4 →
MODE5 → MODE1
ꢀ If you turn off the the power, the video mode will be
back to initial state (MODE1).
This DVD player requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 files).
Customers should also note that permission is required
in order to download MP3 files and music from the
Internet. Our company has no right to grant such per-
mission. Permission should always be sought from the
copyright owner.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Operation - Karaoke function
To adjust the microphone volume
Before you start karaoke
Press MIC/ECHO to select the MIC control mode.
Press 3/4 for the microphone connected to MIC 1/2.
Setting the microphone volume to the centre position
provides the best microphone volume.
Note
You cannot enjoy Karaoke from DVD exclusive out.
“MIC : _ _ _” appears on the TV screen.
You can sing along with a karaoke source (video tape,
VCD, audio CD, Karaoke DVD). You can sing duets if
you use an extra microphone.
To control the echo effect
Press MIC/ECHO to select the ECHO control mode.
Press 3/4. This controls both microphones’ echo effect
in the same way.
To get the best effect, adjust the microphone volume to
a level slightly higher than the music volume.
“ECHO : _ _ _” appears on the TV screen.
Turn on your TV and set it to the AV.
When using an amplifier, turn on the amplifier and
select this player position.
1
Connect a microphone to the MIC 1 jack. To sing
duets, connect another microphone to MIC 2 jack.
2
Karaoke sing-along
Note
The microphone volume and the echo effect will be reset
to the default setting once you disconnect the AC power
cord.
Singing along with karaoke video tapes
Insert a karaoke video tape.
1
The player turns on and starts playing automatically
if you insert a tape with its safety tab removed.
Grading your singing
As an extra challenge, this player can grade your
Press PLAY G.
2 If you want to play back a specific song, perform
singing.
the Karaoke search.
When you have finished singing, your score appears on
the TV screen.
• Karaoke search will be operated only when a
microphone has been plugged in.
Karaoke search
Notes
Press F or G on the remote control.
Press F or G again to play a desired song.
– The unit cannot grade your singing if there is no blank
portion between the tracks.
Now you can enjoy playing karaoke.
– If the sound is reproduced through a stereo amplifier,
turn down the volume of amplifier before operation.
– If streaks appear during playback, select the colour
system that the tape was recorded in (see “To set the
colour system” on page 13).
3
Singing along with karaoke VIDEO CD or DVD
Press
, and place the disc on the disc tray.
1
– If feedback occurs, turn down the microphone or TV
volume, or move the microphone away from the
speakers.
Press PLAY G.
2 The disc tray closes and starts.
Now you can enjoy playing karaoke.
3
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Recording
Copying from DVD to VCP
This unit allows you to copy the contents of a DVD to a
Recording from another video
player
VHS tape with a press of the 0 button.
With this video player you can make recordings from an
external source, such as copying from another video
player or a camcorder.
Note
If the DVD you are attempting to copy is copy protected,
you may not be able to copy the disc.
Note
In the following description, this video player will be one
used for recording and will be referred to as VCP B.
The other appliance will be used for playback and will
be referred to as VCP A.
Insert Disc
1
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
Insert VHS Tape
VCP A should be connected to the AUDIO L/R
(VHS IN)/VIDEO (VHS IN) jack on the rear panel of
your VCP.
2 Insert a blank VHS video tape into the VCP deck.
1
Press DVD so that the DVD indicator lights up.
3
Insert the recorded tape into VCP A and a blank
2 tape into VCP B.
Copy the DVD to VHS tape
4 Press 0.
To start recording, press 0 on VCP B and PLAY G
" The DVD will go into Play mode and the VCP will
go into Record mode.
3 on VCP A.
" If the DVD disc menu appears, you may need to
press PLAY G manually to begin copying.
" If you try to record the copy protected
programme, “COPY PROTECTED DISC”
appears on the TV screen and “LOCK” appears
on the display window.
When you want to finish copying, press STOP on
4 both video players.
" Press ; to still a picture.
Stop the Copy Process
5 Press 9.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Correction
Symptom
ꢀ DVD or VCP button is not switched
properly.
ꢀ Press DVD or VCP on the remote con-
trol, or DVD/VCP on the front panel to
switch the control.
DVD or VCP do not
work properly.
ꢀ The power cord is disconnected.
ꢀ No disc is inserted.
ꢀ Plug the power cord into the wall outlet
securely.
No power.
ꢀ Insert a disc. (Check that the DVD or,
audio CD indicator in the display
window is lit.)
The power is on, but
the DVD player does
not work.
ꢀ The TV is not set to receive DVD signal ꢀ Select the appropriate video input mode
No picture.
output.
on the TV so the picture from the DVD
player appears on the TV screen.
ꢀ The equipment connected with the
audio cable is not set to receive DVD
signal output.
ꢀ Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
No sound.
ꢀ The audio cables are not connected
securely.
ꢀ Connect the audio cable into the jacks
securely.
ꢀ The power of the equipment connected
with the audio cable is turned off.
ꢀ Turn on the equipment connected with
the audio cable.
ꢀ The Digital Audio Output is set to the
wrong position.
ꢀ Set the Digital Audio Output to the
correct position, then turn on the DVD
player again by pressing POWER.
ꢀ The disc is dirty.
ꢀ Clean the disc.
The picture is poor.
ꢀ An unplayable disc is inserted.
ꢀ Insert a playable disc. (Check the disc
type, color system and Regional code.)
The DVD player does
not start playback.
ꢀ The disc is placed upside down.
ꢀ Place the disc with the playback side
down.
ꢀ The disc is not placed within the guide.
ꢀ Place the disc on the disc tray correctly
inside the guide.
ꢀ The disc is dirty.
ꢀ Clean the disc.
ꢀ The Rating level is set.
ꢀ Cancel the Rating function or change
the rating level.
ꢀ There is an obstacle in the path of the
remote control and this unit.
ꢀ Remove the obstacle.
The remote control
does not work properly.
ꢀ The batteries in the remote control are
exhausted.
ꢀ Replace the batteries with new ones.
ꢀ Eject the tape in.
ꢀ Is the cassette compartment empty?
Video tape cannot be
inserted.
ꢀ Audio mode is not set properly.
ꢀ Select “HI-FI” by repeatedly pressing
A. MONITOR on the remote control.
No Hi-Fi sound
Video Head Cleaning
Whenever a video cassette is inserted into or ejected from your VCP, the video head is automatically cleaned. This
should mean that additional head cleaning should not be necessary. However dirt accumulating on the head after a
long period of time can cause the playback picture to become blurred or broken up.
High quality video cassette tapes will not normally deposit dirt onto the video head, but old or damaged tapes might.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 15).
Code Language
6565 Afar
Code Language
7079 Faroese
7082 French
7089 Frisian
Code Language
7678 Lingala
Code Language
8375 Slovak
8376 Slovenian
8377 Samoan
8378 Shona
8379 Somali
8381 Albanian
8382 Serbian
8385 Sudanese
8386 Swedish
8387 Swahili
8465 Tamil
6566 Abkhazian
6570 Afrikaans
6577 Ameharic
6582 Arabic
7679 Laothian
7684 Lithuanian
7686 Latvian, Lettish
7771 Malagasy
7773 Maori
7165 Irish
7168 Scots Gaelic
7176 Galician
7178 Guarani
7185 Gujarati
7265 Hausa
6583 Assamese
6588 Aymara
6590 Azerbaijani
6665 Bashkir
6669 Byelorussian
6671 Bulgarian
6672 Bihari
7775 Macedonian
7776 Malayalam
7778 Mongolian
7779 Moldavian
7782 Marathi
7273 Hindi
7282 Croatian
7285 Hungarian
7289 Armenian
7365 Interlingua
7378 Indonesian
7383 Icelandic
7384 Italian
7783 Malay
8469 Telugu
8471 Tajik
6678 Bengali; Bangla
6679 Tibetan
6682 Breton
7784 Maltese
7789 Burmese
7865 Nauru
8472 Thai
8473 Tigrinya
8475 Turkmen
8476 Tagalog
8479 Tonga
8482 Turkish
8484 Tatar
6765 Catalan
6779 Corsican
6783 Czech
7869 Nepali
7876 Dutch
7387 Hebrew
7465 Japanese
7473 Yiddish
7487 Javanese
7565 Georgian
7575 Kazakh
7576 Greenlandic
7577 Cambodian
7578 Kannada
7579 Korean
7583 Kashmiri
7585 Kurdish
7589 Kirghiz
7879 Norwegian
7982 Oriya
6789 Welsh
6865 Danish
6869 German
6890 Bhutani
6976 Greek
8065 Panjabi
8076 Polish
8487 Twi
8083 Pashto, Pushto
8084 Portuguese
8185 Quechua
8277 Rhaeto-Romance
8279 Rumanian
8285 Russian
8365 Sanskrit
8368 Sindhi
8575 Ukrainian
8582 Urdu
6978 English
6979 Esperanto
6983 Spanish
6984 Estonian
6985 Basque
7065 Persian
7073 Finnish
7074 Fiji
8590 Uzbek
8673 Vietnamese
8679 Volapük
8779 Wolof
8872 Xhosa
8979 Yoruba
9072 Chinese
9085 Zulu
8372 Serbo-Croatian
8373 Singhalese
7665 Latin
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Country Code List
Enter the appropriate code number for the initial setting “Country Code” (See page 17).
Code Country
Code Country
Code Country
Code Country
AD
AE
AF
AG
AI
Andorra
ER
ES
ET
FI
Eritrea
Spain
Ethiopia
Finland
LC
LI
LK
LR
LS
LT
LU
LV
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libya
Morocco
Monaco
SC
SD
SE
SG
SH
SI
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Islands
Slovak Republic
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Saint Tome and Principe
Former USSR
El Salvador
Syria
Swaziland
Turks and Caicos Islands
Chad
French Southern
Territories
Togo
Thailand
Tadjikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
FJ
Fiji
AL
FK
FM
FO
FR
FX
Falkland Islands
Micronesia
Faroe Islands
France
France (European
Territory)
Gabon
Great Britain
Grenada
Georgia
French Guyana
Ghana
Gibraltar
Greenland
Gambia
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
SJ
LY
SK
SL
SM
SN
SO
SR
ST
SU
SV
SY
SZ
TC
TD
TF
MA
MC
MD
MG
MH
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
Moldavia
Madagascar
Marshall Islands
Macedonia
Mali
Myanmar
Mongolia
Aruba
Azerbaidjan
Bosnia-Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Ivory Coast
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Former Czechoslovakia
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Macau
Northern Mariana Islands
Martinique (French)
Mauritania
Montserrat
Malta
Guinea
Guadeloupe (French)
Equatorial Guinea
Greece
S. Georgia & S. Sandwich
Isls.
Guatemala
Guam (USA)
Guinea Bissau
Guyana
Hong Kong
Heard and McDonald
Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran
Iceland
Italy
Jamaica
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UK
UM
BJ
Mauritius
Maldives
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CS
CU
CV
CX
CY
CZ
DE
DJ
GT
GU
GW
GY
HK
HM
MW Malawi
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
Mexico
Malaysia
Mozambique
Namibia
New Caledonia (French)
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
Polynesia (French)
Papua New Guinea
Philippines
Pakistan
HN
HR
HT
HU
ID
IE
IL
IN
IO
Ukraine
Uganda
United Kingdom
USA Minor Outlying
Islands
United States
Uruguay
Uzbekistan
Vatican City State
Saint Vincent &
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (USA)
Vietnam
Vanuatu
Wallis and Futuna Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
US
UY
UZ
VA
VC
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
VE
VG
VI
Jordan
Japan
Kenya
Poland
Saint Pierre and Miquelon
Pitcairn Island
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
Saudi Arabia
Solomon Islands
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Kyrgyzstan
Cambodia6
Kiribati
Comoros
Saint Kitts & Nevis Anguilla
North Korea
South Korea
Kuwait
DK
DM
DO
DZ
EC
EE
EG
EH
Cayman Islands
Kazakhstan
Laos
Lebanon
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
General
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
AC 110-240V , 50/60 Hz
20W
430 X 97.5 X 360 mm (w/h/d)
5.3 kg
Operating temperature
Operating humidity
5˚C to 35˚C
5 % to 90 %
System
Laser
Semiconductor laser, wavelength 650 nm
Double azimuth 4 heads, helical scanning.
PAL/NTSC
Video Head system
Signal system
Frequency response
DVD (PCM 96 kHz): 2 Hz to 44 kHz
DVD (PCM 48 kHz): 2 Hz to 22 kHz
CD: 2 Hz to 20 kHz
Signal-to-noise ratio
Harmonic distortion
Dynamic range
More than 100dB (ANALOG OUT connectors only)
Less than 0.008%
More than 95 dB (DVD)
More than 95 dB (CD)
Wow and flutter
Less than detected value ( 0.001% W PEAK)
Inputs (VCP)
Audio
-6.0dBm, more than 47 kohms
1.0 Vp-p, 75 ohms, unbalanced
Video
Outputs (DVD)
VIDEO OUT
1 Vp-p 75 ohms, sync negative
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
0.5 V (p-p), 75 Ω, RCA jack x 1
Audio output (digital audio)
Audio output (analog audio)
2.0 Vrms (1 KHz, 0 dB), 330 Ω, RCA jack (L, R)
Outputs (VCP/DVD)
Audio
Video
-6.0dBm, less than 1 kohms
1.0 Vp-p, 75 ohms, unbalanced
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
ꢀ Design and specifications are subject to change without notice.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Korea
1102-AH-ID-LG
AG
COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.
P/N : 3834RP0086Q
Download from Www.Somanuals.com. All Manuals Search And Download.
|