JVC CRT Television HV 28P37SJE User Manual

HV-36P38SJE  
HV-32P37SJE  
HV-28P37SJE  
COLOUR TELEVISION  
INSTRUCTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Thank you for buying this JVC colour television.  
To make sure you understand how to use your new TV, please read this manual thoroughly before you  
begin.  
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
CAUTION:  
• Operate only from the power source specified  
(AC 220 – 240 V, 50 Hz) on the unit.  
• Avoid damaging the AC plug and power cord.  
• When you are not using this unit for a long  
period of time, it is recommended that you  
disconnect the power cord from the main  
outlet.  
• The main power button on the TV does not  
fully isolate the TV from the mains supply. If  
you are not going to use this TV for a long  
period of time, be sure to disconnect the mains  
plug from the mains outlet.  
Avoid improper installation and never put the unit where good  
ventilation is not possible.  
When installing this TV, distance recommendations must be  
maintained between the set and the wall, as well as inside a tightly  
enclosed area or piece of furniture.  
Adhere to the minimum distance guidelines shown for safe operation.  
Failure to heed the following precautions may result in damage to the TV or  
remote control.  
DO NOT block the TV’s ventilation openings or holes.  
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be  
able to get out.)  
DO NOT place anything on top of the TV.  
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)  
DO NOT allow objects or liquid into the cabinet openings.  
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)  
DO NOT place any naked flame sources, such as lighted candles, on the TV.  
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.  
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.  
Never use any cleaner or detergent on it.  
In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it  
yourself or remove the rear cover.  
D.I.S.T. demonstration  
To start the D.I.S.T. demonstration:  
Press the H button to display the menu bar. Then press the yellow button.  
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.  
To quit the D.I.S.T. demonstration:  
Press the yellow button, b button, p p buttons or any of the number buttons.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
Setting up your TV ...................................5  
Connecting the aerial and video cassette  
recorder (VCR)....................................... 5  
Connecting and placing the woofer unit  
(HV-36P38SJE only) .............................. 7  
Connecting the power cord to the AC  
outlet....................................................... 8  
Putting the batteries into the remote  
control..................................................... 8  
Initial settings ............................................. 8  
T-V LINK functions................................... 12  
SOUND menu ......................................... 30  
STEREO / I • II.........................................30  
BASS........................................................ 30  
TREBLE ................................................... 30  
BALANCE ................................................ 30  
HEADPHONE VOLUME .......................... 30  
3D CINEMA SOUND................................ 30  
FEATURES menu................................... 31  
SLEEP TIMER .........................................31  
CHILD LOCK............................................ 31  
APPEARANCE.........................................32  
BLUE BACK............................................. 32  
TV buttons and functions......................13  
Turn the main power on........................... 14  
Turn the TV on from standby mode ......... 14  
Choose a TV channel .............................. 14  
Adjust the volume .................................... 14  
SET UP menu ......................................... 33  
AUTO PROGRAM.................................... 33  
EDIT/MANUAL.........................................33  
LANGUAGE ............................................. 38  
PICTURE TILT.........................................38  
DECODER (EXT-2).................................. 38  
EXT SETTING.......................................... 39  
Remote control buttons and  
functions..............................................15  
Turn the TV on or off from standby mode ... 15  
Choose a TV channel and watch images  
from external devices ........................... 16  
Adjust the volume .................................... 17  
Information function ................................. 17  
ZOOM function......................................... 18  
3D CINEMA SOUND function.................. 19  
Return to TV channel instantly................. 19  
Using the FREEZE function..................... 19  
Using the MULTI-PICTURE function ....... 20  
Operating a JVC brand VCR or DVD  
Additional preparation .......................... 42  
Connecting external equipment ............... 42  
Troubleshooting .................................... 45  
Specifications ........................................ 47  
player.................................................... 21  
Teletext function ....................................22  
Basic operation ........................................ 22  
Using the List Mode ................................. 22  
Hold.......................................................... 23  
Sub-page ................................................. 23  
Reveal...................................................... 23  
Size.......................................................... 23  
Index........................................................ 23  
Cancel...................................................... 24  
Using the TV’s menu..............................25  
Basic operation ........................................ 25  
PICTURE menu.......................................26  
PICTURE MODE ..................................... 26  
CONTRAST ............................................. 26  
BRIGHT ................................................... 26  
SHARP..................................................... 26  
COLOUR.................................................. 26  
HUE ......................................................... 26  
COLOUR TEMP....................................... 26  
FEATURES.............................................. 27  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Caution  
• Turn off all the equipment including the TV before connecting anything.  
Connecting the aerial and video cassette recorder (VCR)  
• The connecting cables are not provided.  
• For further details, refer to the manuals provided with the devices to be connected.  
If you are connecting a VCR,  
HV-36P38SJE  
Back of the TV  
Aerial  
follow A B C in the diagram  
opposite.  
75-ohm  
Coaxial  
Cable  
If you are not connecting a VCR,  
follow 1.  
EXT-  
4
EXT-1  
To use the T-V LINK functions, you must  
have a T-V LINK compatible VCR  
connected by a SCART cable C to the EXT-  
2 terminal on the TV. For details about T-V  
LINK functions, see “T-V LINK functions”  
on page 12.  
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
21-pin  
75-ohm  
Coaxial  
Cable  
SCART  
Cable  
• You can watch a video using the VCR  
without doing C. For details, see your  
VCR instruction manual.  
To Aerial  
Input  
VCR  
• To connect more equipment, please see  
“Connecting external equipment” on  
page 42.  
• To connect additional audio equipment,  
see “Connecting speakers/amplifier” on  
page 44.  
• If you connect a decoder to a T-V LINK  
compatible VCR, set the DECODER  
(EXT-2) function to ON. For details, see  
“DECODER (EXT-2)” on page 38.  
Otherwise, you will not be able to watch  
scrambled channels.  
To Aerial  
Output  
AV IN/OUT  
Terminal  
HV-32P37SJE/HV-28P37SJE  
Aerial  
75-ohm  
Coaxial  
Cable  
Back of the TV  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
21-pin  
SCART  
Cable  
75-ohm  
Coaxial  
Cable  
To Aerial  
Input  
VCR  
To Aerial  
Output  
AV IN/OUT  
Terminal  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Rear Panel  
HV-36P38SJE  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
1 Aerial socket (page 5)  
2 Woofer terminal (pages 7)  
3 EXT-1 terminal (pages 5, 39, 42)  
4 EXT-2 terminal (pages 5, 12, 39, 42)  
5 EXT-3 terminal (pages 39, 42)  
6 EXT-4 terminal (pages 39, 42)  
7 AUDIO OUT terminal (page 44)  
HV-32P37SJE/HV-28P37SJE  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
1 Aerial socket (page 5)  
2 EXT-1 terminal (pages 5, 39, 42)  
3 EXT-2 terminal (pages 5, 12, 39, 42)  
4 EXT-3 terminal (pages 39, 42)  
5 EXT-4 terminal (pages 39, 42)  
6 AUDIO OUT terminal (page 44)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Place the woofer unit within the range  
of the connection cable.  
It is recommended that the woofer unit be  
placed with the speaker facing forwards.  
Connecting and placing the  
woofer unit (HV-36P38SJE  
only)  
Connect the supplied woofer connector to the  
woofer terminal on the back of the TV.  
If the woofer unit is not connected, you will  
not be able to enjoy the bass sound.  
• Connect so that the lever is raised.  
Lever  
EXT- 4  
T-1  
X
Y
T-2  
X
E
S
L
Pb  
R
r
P
T-3  
X
E
S
Pay attention to the following in order  
to prevent unnatural colours from  
appearing in the corner of the screen.  
• Place the woofer unit at least 20 cm away  
from either side of the TV.  
L
T
U
O
IO  
D
U
A
R
• When disconnecting the woofer  
connector, do so while pushing the lever.  
• Do not place the woofer unit on top of the  
TV.  
• When the TV is used on a TV stand or  
table, do not place the woofer unit  
underneath the TV.  
Placing the woofer unit  
As shown in the diagram, fix the  
supplied stoppers to the four corners  
of the side of the woofer unit that will  
be used as the base.  
The woofer unit can be used either standing  
up or lying down.  
There is no difference between the top and  
bottom of the woofer unit irrespective of  
whether it is being used standing up or lying  
down.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Connecting the power cord to  
the AC outlet  
Initial settings  
When the TV is first turned on, it goes into  
the initial settings mode, and you will see the  
JVC logo. Follow the instructions on the  
screen display to make the initial settings.  
Caution  
• Operate only from the power source specified  
(AC 220 – 240 V, 50 Hz) on the unit.  
Yellow button  
Blue button  
Putting the batteries into the  
remote control  
7 buttons  
Use two AA/R6 dry cell batteries.  
Insert the batteries from the - end, making  
sure the + and - polarities are correct.  
1 Press the main power button on the  
TV  
The power lamp lights red (for power on),  
then green (for TV on) and the JVC logo  
appears.  
HV-36P38SJE  
• Follow the warnings printed on the  
batteries.  
• Battery life is about six months to one  
year, depending on how much you use the  
remote control.  
Power lamp  
Main power  
button  
HV-32P37SJE/HV-28P37SJE  
• The batteries we supply are only for  
setting up and testing your TV, please  
replace them as soon as you need to.  
• If the remote control does not work  
properly, replace the batteries.  
Power lamp  
Main power  
button  
• If the power lamp stays red and does  
not change to green:  
Your TV is in the standby mode. To  
turn the TV on, set the VCR/TV/DVD  
switch on the remote control to the TV  
position and press the # button. (See  
page 15.)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
• If the JVC logo does not appear this is  
because your TV has already been  
turned on for the first time:  
use the “LANGUAGE” and “AUTO  
PROGRAM” functions to make the  
initial settings. For details, see “SET  
UP menu” on page 33.  
4 Press the 5 and 6 buttons to  
choose the country where you are  
• To receive SKY 1 you need a satellite  
tuner. You must have the satellite tuner  
set to SKY 1 before starting the AUTO  
PROGRAM function which follows.  
5 Press the blue button to start the  
AUTO PROGRAM function  
The AUTO PROGRAM menu appears  
and received TV channels are  
automatically stored in the programme  
numbers (PR).  
2 Press the a button  
The LANGUAGE menu appears.  
> LANGUAGE  
>> AUTO PROGRAM  
CH 28  
14%  
OK  
D0002(E)-EN  
OK  
3 Press the 6 buttons to choose  
ENGLISH. Then press the a  
button  
D0004-EN  
• Perform the “ACI function” operation  
(see page 10) when “ACI START/ACI  
SKIP” is displayed.  
• To cancel the AUTO PROGRAM  
function:  
The on-screen display will then be in  
English.  
The COUNTRY menu appears as a sub-  
menu of the AUTO PROGRAM function.  
There are two COUNTRY menus.  
Pressing the yellow button changes the  
COUNTRY menu as follows:  
Press the b button.  
After the TV channels have been  
registered in the programme  
numbers (PR), the EDIT menu  
appears  
> COUNTRY  
> EDIT  
START  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
OK  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
MORE  
> COUNTRY  
ID  
MANUAL  
OK  
MOVE  
INSERT DELETE  
D0038-EK  
• If you want to, you can now edit the  
programme numbers (PR) using the  
EDIT/MANUAL function. For details,  
see “EDIT/MANUAL” on page 33.  
• If you do not want to edit programme  
numbers (PR), go to the next step.  
START  
OK  
MORE  
D0003-EN  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
• The AUTO PROGRAM function does not  
set the programme number PR 0 (AV) for  
your video cassette recorder. You will  
need to set this using the MANUAL  
function.  
6 Press the a button to display the  
T-V LINK menu  
T-V LINK  
DOWNLOAD TV  
VCR  
• In some areas you may get TV reception  
from more than one transmitter, for  
example different ITV regions. In this  
case each TV channel could be set twice.  
If this happens, the first set of channels  
will have the stronger signal. If you want  
to delete the second set of channels, you  
will have to do it manually (see page 33).  
OK  
EXIT  
D0005-EN  
If you do not have a T-V LINK  
compatible VCR connected:  
Press the b button to exit the T-V LINK  
menu.  
The T-V LINK menu disappears.  
If you have a T-V LINK compatible  
VCR connected to the EXT-2  
terminal:  
Follow the operating procedure  
“Downloading the data to VCR” on  
page 11 to transmit the Programme  
number (PR) data.  
Now, the initial settings are complete,  
and you can watch the TV  
When the COUNTRY setting is  
UNITED KINGDOM:  
ACI function  
This TV has an ACI function which decodes  
the ACI (Automatic Channel Installation)  
data.  
BBC1, BBC2, ITV, Channel 4 and  
Channel 5 are automatically set to the  
programme numbers PR1 to PR5. If the  
TV doesn't receive one of these TV  
channels, that programme number (PR)  
will not be set. Programme number PR6 is  
not normally set.  
Using the ACI function allows all TV  
channels transmitted from the cable TV  
station to be properly registered quickly  
according to the data from the cable TV  
station.  
If “ACI START/ACI SKIP” appears in  
the AUTO PROGRAM menu:  
You can use the ACI (Automatic Channel  
Installation) function to decode the ACI data  
and complete the registration of all the TV  
channels in a short period of time.  
When the COUNTRY setting is  
IRELAND:  
If your TV can detect the TV channel  
name from the TV channel broadcast  
signal, the TV channel name is assigned  
to the programme number (PR) to which  
the TV channel has been set. However,  
which TV channels are set to which  
programme numbers (PR) will depend on  
the area in which you live.  
• If a TV channel you want to view is not  
set to a programme number (PR), you can  
set it using the MANUAL function. For  
details, see “EDIT/MANUAL” on  
page 33.  
Press the 6 buttons to choose ACI  
START. Then press the a button to  
start the ACI function  
Depending on your cable TV station, there  
may be a broadcast selection menu set up by  
the cable TV station.  
Follow the menu instructions and use the  
5 and 6 buttons to operate the menu.  
After you have made the setting, press the  
a button.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
• If you have any questions about the items  
in the Broadcast Selection menu or how to  
operate the menu, please contact your  
cable TV station.  
• If you don’t want to use the ACI function,  
press the 6 buttons to choose ACI  
SKIP and then press a.  
1 Turn on the VCR  
2 Press the a button  
The data transmission begins.  
DOWNLOAD TV  
VCR  
TRANSFER. . . . .  
D0037-EN  
• When the cable TV broadcast reception is  
poor, the ACI function will not work  
properly.  
The T-V LINK menu disappears once the  
data transmission ends.  
• If there is an error in the ACI data itself,  
the TV channel cannot be registered  
properly. If this happens, turn the ACI  
function off (ACI SKIP) and use the  
AUTO PROGRAM function.  
Alternatively, use the EDIT/MANUAL  
function to correct the Programme  
number (PR) setting.  
When the T-V LINK menu is  
changed over to another menu:  
The TV has finished its menu. This new  
menu is operated from the VCR. See the  
VCR instruction manual for what to do  
next.  
If “FEATURE NOT AVAILABLE”  
appears at the T-V LINK menu:  
Check the following three items. Then  
press the 2 button to retry data  
transmission.  
• Has a T-V LINK compatible VCR  
been connected to the EXT-2  
terminal?  
• Has the VCR power been turned on?  
• Does the SCART cable that is  
connected to the EXT-2 terminal to T-  
V LINK compatible VCR have all its  
proper connections?  
If “ACI ERROR” is displayed in the  
AUTO PROGRAM menu:  
“ACI ERROR” means that the ACI function  
is not working properly. Press the 2 button  
to start the ACI function again.  
If “ACI ERROR” still appears even after you  
have tried to start the ACI function several  
times, press the 3 button to start the AUTO  
PROGRAM function. It does not cause any  
problem because all the TV channels are  
registered to the Programme numbers (PR)  
by the AUTO PROGRAM function.  
Downloading the data to VCR  
You can transmit to the latest Programme  
numbers (PR) data to a VCR with the T-V  
LINK function.  
Caution  
• This only works when a T-V LINK  
compatible VCR is connected to the  
EXT-2 terminal.  
• This only works when the T-V LINK  
menu is being displayed.  
T-V LINK  
DOWNLOAD TV  
VCR  
OK  
EXIT  
D0005-EN  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
Direct Rec  
T-V LINK functions  
“What You See Is What You Record”  
When you have a T-V LINK compatible  
VCR connected to the EXT-2 Terminal on  
the TV, it is easier to set up the VCR and to  
view videos. T-V LINK uses the following  
features:  
You can easily record to VCR the images  
that you are watching on the TV.  
For details, read the manual for your VCR.  
Use your VCR controls. “VCR IS  
RECORDING” is displayed.  
To use T-V LINK functions:  
A “T-V LINK compatible VCR” means a  
JVC video cassette recorder with the T-V  
LINK logo, or with one of the following  
logos. However, these VCRs may support  
some or all of the features described earlier.  
For details, see your VCR instruction  
manual.  
In the following situations, the VCR  
will stop recording if the TV is turned  
off, if the TV channel or input is  
changed, or if the menu is displayed  
on the TV:  
• when recording images from an external  
device connected to the TV (for example  
a camcorder)  
• when recording a TV channel after it has  
been unscrambled on a decoder  
• when recording a TV channel by using the  
TV’s output because the VCR’s own  
tuner cannot properly receive that  
channel.  
“Q-LINK” (a trademark of Panasonic  
Corporation)  
“Data Logic” (a trademark of Metz  
Corporation)  
“Easy Link” (a trademark of Phillips  
Corporation)  
“Megalogic” (a trademark of Grundig  
Corporation)  
“SMARTLINK” (a trademark of Sony  
When the VCR is not ready (for example  
when there is no tape inserted), “NO  
RECORDING” is displayed.  
You cannot carry out Direct Rec using your  
TV’s control.  
Corporation).  
Pre-set download  
The VCR will automatically download the  
registered data on the TV channels from the  
TV. This means you do not need to set up the  
program channels on your VCR manually.  
The preset download function automatically  
begins when the initial setting is complete or  
whenever you carry out the AUTO  
Generally, the VCR cannot record a TV  
channel that it cannot receive properly on its  
own tuner, even if you can view that TV  
channel on the TV. However, some VCRs  
can record a TV channel by using the TV’s  
output if that channel can be viewed on the  
TV. For details, see your VCR instruction  
manual.  
PROGRAM or EDIT/MANUAL functions.  
You can also carry out this function using  
your VCR controls.  
When “FEATURE NOT AVAILABLE” is  
displayed:  
If “FEATURE NOT AVAILABLE” is  
displayed, the download was not performed  
correctly. Before trying to download again,  
check that:  
• the VCR power is turned on  
• the VCR is T-V LINK compatible  
• the VCR is connected to the EXT-2  
terminal  
• the SCART cable is fully wired.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV buttons and functions  
HV-36P38SJE  
HV-32P37SJE/HV-28P37SJE  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT  
-2  
S
S
R
P
E
X
T
L
EXT-3  
5
S
R
L
A
U
D
I
O
O
U
T
R
S
L
R
P
EXT-5  
S
S
L
R
P
E
X
T
P
EXT-5  
L
5
R
See the pages in parentheses for details.  
See the pages in parentheses for details.  
1 Remote control sensor  
1 Remote control sensor  
2 Power lamp (pages 8, 14)  
2 Power lamp (pages 8, 14)  
3 Main power button (pages 8, 14)  
4 Headphone jack (mini jack) (page 42)  
5 P p buttons/ q buttons (page 14)  
6 r (Volume) button (page 14)  
7 EXT-5 terminal (pages 39, 42)  
3 Main power button (pages 8, 14)  
4 Headphone jack (mini jack) (page 42)  
5 P p buttons/ q buttons (page 14)  
6 r (Volume) button (page 14)  
7 EXT-5 terminal (pages 39, 42)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV buttons and functions  
Turn the main power on  
Press the main power button on the  
TV.  
The power lamp lights red and your TV is in  
standby mode.  
• If the power lamp lights green, the TV is  
already on.  
To turn the main power off:  
Press the main power button again.  
The power lamp goes off.  
Caution  
• The main power button on the TV does  
not fully isolate the TV from the AC  
supply. If you are not going to use the TV  
for a long period, be sure to disconnect  
the AC plug from the AC socket.  
Turn the TV on from standby  
mode  
Press the P p buttons to turn the TV  
on from standby mode  
Choose a TV channel  
Press the P p buttons to choose a  
programme number (PR) or an EXT  
terminal  
Adjust the volume  
1 Press the r (Volume) button  
The volume level indicator appears.  
2 Press the q buttons while the  
volume level indicator is displayed  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
1 Muting button  
2 Number buttons  
3 Information button  
4 c button  
5 3 sound button  
6 b button  
7 7 buttons  
8 g (Text) button  
9 p p buttons  
1
2
=
~
0 VCR/DVD/Teletext control buttons  
- p buttons  
= # (Standby) button  
~ VCR/TV/DVD switch  
! G button  
3
4
!
@
#
@ Colour button  
# X (Multi) button  
$ f/g (Freeze/Swap) button  
% H button  
^ a button  
& b button  
$
5
6
%
^
* r (Volume) q buttons  
7
8
&
*
Turn the TV on or off from  
standby mode  
9
Press the # (standby) button to turn  
the TV on or off.  
When the TV is turned on, the power lamp  
changes from red to green.  
0
-
• The power can be turned on by pressing  
the b button, p p buttons or Number  
buttons.  
To turn the TV on or off, set the VCR/TV/  
DVD switch on the remote control to the  
TV position and press the # button.  
If the VCR/TV/DVD switch on the remote  
control is set to a position other than TV,  
the TV will not be turned on or off even if  
the # button is pressed.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
• This TV set has a function which can  
automatically change over the input  
according to a special signal output  
from an external device. (The EXT-4  
and EXT-5 terminals do not support  
this function.)  
• Since this TV is designed to make full  
use of the resolution of the original  
video source, the motion may appear  
unnatural when the video source is  
input with 625p progressive-scanning  
component signals.  
If this happens, change the output  
setting of the connected device to 625i  
interlace-scanning component signal  
output. See the instructions that came  
with the device for more information.  
Choose a TV channel and  
watch images from external  
devices  
• If the picture is tilted, correct it. See  
“PICTURE TILT” on page 38.  
Use the number buttons:  
Enter the programme number (PR)  
of the channel using the number  
buttons.  
Example:  
• PR 6 press 6  
• PR 12 press 1 and 2  
Use the p p buttons:  
Press the p p buttons to  
choose the programme number  
(PR) you want or an EXT terminal.  
To return to a TV channel:  
Press the b button, the 6 buttons or the  
number buttons.  
Use the AV button:  
Press the AV button to choose an  
EXT terminal.  
To use the programme number PR 0  
(AV):  
When the TV and VCR are connected only  
by the aerial cable, choosing the programme  
number PR 0 (AV) allows you to view  
images from the VCR. Set the VCR RF  
channel to the programme number PR 0  
(AV) manually. For details, see “EDIT/  
MANUAL” on page 33.  
TV mode  
EXT modes  
Programme  
numbers  
PR 1 – PR 99  
EXT-2  
EXT-1  
or  
EXT-3  
or  
S3  
E3  
Pressing the G button changes the choice as  
follows:  
EXT-5  
EXT-4  
EXT modes  
TV mode  
or  
EXT-2  
EXT-1  
Programme  
PR 0  
• You can choose a video input signal  
from the S-VIDEO signal (Y/C signal)  
and regular video signal (composite  
signal). For details, see “S-IN (S-  
VIDEO input)” on page 39.  
• If you do not have a clear picture or no  
colour appears, change the colour  
system manually. See “COLOUR  
SYSTEM” on page 28.  
numbers  
or  
PR 1 – PR 99  
EXT-3  
or S3  
E3  
EXT-5  
EXT-4  
or  
• The VCR sends its playback image along  
the aerial cable as an RF (radio frequency)  
signal.  
• If you choose an EXT terminal with no  
input signal, the EXT terminal number  
becomes fixed on the screen.  
• Also see your VCR instruction manual.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
Time display:  
The current time of the teletext data is  
displayed.  
Adjust the volume  
Press the r q buttons to adjust  
the volume.  
The volume indicator appears and the  
volume changes as you press the r q  
buttons.  
If the TV has not received a TV channel that  
has teletext programmes since it was turned  
on, the time display is blank. To view the  
current time, choose a TV channel that has  
teletext programmes. The time will continue  
to be displayed until the TV is turned off  
even if you choose other TV channels.  
• An incorrect current time is sometimes  
displayed when watching videos.  
Muting the sound  
Press the (muting) button to  
l
turn off the sound.  
Pressing the (muting) button again  
l
PR LIST:  
restores the previous volume level.  
The programme number (PR) and EXT  
terminal list is displayed.  
Information function  
Pressing the a button after choosing the  
programme number (PR) or EXT terminal  
with the 7 buttons will display the  
chosen programme or EXT terminal.  
• For programme numbers (PR) for which  
the CHILD LOCK function is set, the n  
(CHILD LOCK) mark is displayed. For  
details see “CHILD LOCK” on page 31.  
You can see the channel number of the  
programme you are watching, the current  
time or the PR LIST.  
From the PR LIST, you can choose a channel  
or EXT terminal.  
Press the  
(Information) button to  
h
display the information you want to  
see.  
Pressing the  
(Information) button changes  
h
the display as follows:  
PR LIST  
PR  
ID  
Channel number display  
12 : 00  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
BBC1  
No indication  
OK  
-10  
+10  
D0011-EN  
Channel number display:  
The channel number and channel name  
(when the channel name is registered) of the  
programme you are watching or the EXT  
terminal number is displayed.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
16:9 ZOOM:  
This zooms up the wide picture (16:9 aspect  
ratio) to the full screen.  
ZOOM function  
You can change the screen size according to  
the picture aspect ratio. Choose the optimum  
one from the following ZOOM modes.  
AUTO:  
16:9 ZOOM SUBTITLE:  
This zooms up the wide picture (16:9 aspect  
ratio) with subtitles to the full screen.  
When a WSS (Wide Screen Signalling)  
signal, which shows the aspect ratio of the  
picture, is included in the broadcast signal or  
the signal from an external device, the TV  
automatically changes the ZOOM mode to  
16:9 ZOOM mode or FULL mode according  
to the WSS signal.  
If a WSS signal is not included, the picture is  
displayed according to the ZOOM mode set  
with the 4:3 AUTO ASPECT function.  
• For details of the 4:3 AUTO ASPECT  
function, see “4:3 AUTO ASPECT” on  
page 29.  
FULL:  
This uniformly stretches the left and right  
sides of a normal picture (4:3 aspect ratio) to  
fill the wide TV screen.  
• For 16:9 aspect ratio pictures that have  
been squeezed into a normal picture (4:3  
aspect ratio), use the FULL mode to  
restore the picture to its original shape.  
• When the AUTO (WSS) mode does not  
function correctly due to poor WSS signal  
quality or when you want to change the  
ZOOM mode, press the c button  
and change to another ZOOM mode.  
Choose the ZOOM mode  
REGULAR:  
Use to view a normal picture (4:3 aspect  
ratio) as this is its original shape.  
1 Press the c button to display  
the ZOOM menu  
ZOOM  
AUTO  
REGULAR  
PANORAMIC  
14:9 ZOOM  
16:9 ZOOM  
16:9 ZOOM SUBTITLE  
FULL  
PANORAMIC:  
This stretches the left and right sides of a  
normal picture (4:3 aspect ratio) to fill the  
screen, without making the picture appear  
unnatural.  
OK  
D0009-EN  
2 Press the 6 buttons to choose a  
ZOOM mode. Then press the a  
button  
• The top and bottom of the picture are  
slightly cut off.  
The picture expands and the chosen  
ZOOM mode is displayed in about 5  
seconds.  
• The ZOOM mode may be  
automatically changed by the control  
signal from an external device. When  
you want to return to the previous  
ZOOM mode, choose the ZOOM  
mode again.  
14:9 ZOOM:  
This zooms up the wide picture (14:9 aspect  
ratio) to the upper and lower limits of the  
screen.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
Adjusting the visible area of the  
picture  
3D CINEMA SOUND function  
If subtitles or the top (or bottom) of the  
picture are cut off, you can adjust the visible  
area of the picture manually.  
You can enjoy sounds with a wider  
ambience.  
• This function does not work for the sound  
from headphones.  
1 Press the c button  
The ZOOM menu appears.  
Press the 3 button and choose  
“ON”, “MONO” or “OFF”.  
2 Press the a button to display the  
ZOOM mode indicator  
ON:  
Choose to add the 3D CINEMA SOUND  
effect to stereo sound.  
The indicator appears.  
16 : 9 ZOOM  
MONO:  
D0010-EN  
Choose to add the 3D CINEMA SOUND  
effect to mono sound.  
3 While it is displayed, press the 6  
buttons to change the position of  
the picture  
OFF:  
Choose to cancel the 3D CINEMA SOUND  
effect.  
• The 3D CINEMA SOUND effect can be  
adjusted with the “3D CINEMA  
SOUND” menu (see page 30).  
• You cannot adjust the visible area in  
REGULAR or FULL mode.  
Return to TV channel instantly  
You can return to a TV channel instantly.  
Press the b button  
The TV returns to the TV mode and a TV  
channel appears.  
Using the FREEZE function  
You can view the current programme as a  
still picture.  
1 Press the f button  
The still picture of the current picture will  
appear.  
current  
programme  
still picture  
D0056-EN  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
To cancel the FREEZE function:  
Press the f button, the p p buttons or  
the number buttons.  
• When set to 2-pictures multi, you can  
view a TV picture and a picture from  
an external device. You can not view a  
TV picture on more than one screen at  
the same time.  
• When 12-pictures multi is set, pictures  
from external devices are not  
displayed.  
• The FREEZE function does not work  
while a sub-picture is displayed.  
• The still picture cannot be output from  
the TV.  
• The FREEZE function does not work  
for pictures of 625p, 525p and 1125i  
signals.  
• When set to 2-pictures multi, the main-  
picture can be changed by pressing the  
p p buttons. The sub-picture screen  
can be changed by pressing the p  
buttons.  
When set to 12-pictures multi and  
there are more than 12 pictures, the  
next or previous 12 screens can be  
displayed by pressing the p buttons.  
Using the MULTI-PICTURE  
function  
1 Press the X button  
The MULTI-PICTURE menu appears.  
1
2
12  
Changing the sub-picture  
Displaying the next or  
previous 12 screens  
D0101-EN  
2 Press the 5 buttons to choose  
the number of screens and then  
press the a button  
• When set to 2-pictures multi, press the  
g (swap) button to switch the main-  
picture and sub-picture.  
Choose to return to one screen.  
1
2-pictures multi function does not  
work for a picture of 1125i signal.  
D0102  
• A picture of 625p or 525p signal  
cannot be displayed as the sub-picture.  
Pay attention to the following.  
Choose to change to 2-pictures multi.  
2
D0103  
- When the EXT-4 picture is a picture  
of 625p or 525p signal, you cannot  
choose EXT-4 with the p buttons.  
- When the EXT-4 picture signal is  
changed to 625p, 525p or 1125i  
Choose to change to 12-pictures multi.  
12  
D0104  
2-pictures multi:  
signal while the EXT-4 picture is  
displayed as the sub-picture, the 2-  
pictures multi function is cancelled.  
Main-  
picture  
Sub-  
picture  
D0056-EN  
12-pictures multi:  
Still  
pictures  
Moving  
picture  
D0058-EN  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
- The pictures cannot be swapped  
when a picture of 625p or 525p  
signal from EXT-4 is being  
Operating a JVC brand VCR or  
DVD player  
displayed as the main picture.  
These buttons will operate a JVC brand VCR  
or DVD player. Pressing a button that looks  
the same as the device’s original remote  
control button has the same effect as the  
original remote control.  
• Do not press the g (swap) button  
while you are recording the TV output  
on the VCR. If you do, the TV output  
signal will change.  
• You cannot view a scrambled channel  
in the sub-picture. If the g (swap)  
button is pressed when viewing a  
scrambled channel in the main-picture  
using an external decoder, the channel  
you have been viewing in the sub-  
picture will appear in both the main-  
picture and sub-picture.  
• When set to 2-pictures multi and the  
headphones are connected, the sound  
for the main-picture is output from the  
TV speakers and the sound from the  
sub-picture is output from the  
1 Set the VCR/TV/DVD Switch to the  
VCR or DVD position  
VCR:  
When you are operating the VCR, set the  
switch to the VCR position.  
• You can turn the VCR on or off with  
the # (standby) button.  
DVD:  
When you are operating the DVD player,  
set the switch to the DVD position.  
• You can turn the DVD player on or off  
with the # (standby) button.  
headphones.  
- Adjust the volume of the sub-picture  
sound from the headphones with  
“HEADPHONE VOLUME” in the  
“SOUND” menu (see page 30).  
- The main-picture sound can not be  
heard through the headphones.  
• When set to 12-pictures multi, press  
the 7 buttons to choose the  
screen you want to view and the press  
the a button to display that picture  
on the whole screen.  
• The BLUE BACK function does not  
work when the MULTI-PICTURE  
function is being used.  
• The ZOOM function does not work  
when the MULTI-PICTURE function  
is being used.  
2 Press the VCR/DVD Control Button  
to control your VCR or DVD player  
• If your device is not made by JVC,  
these buttons will not work.  
• Even if your device is made by JVC,  
some of these buttons may not work,  
depending on the device you are using.  
• You can use the p buttons to choose  
a TV channel the VCR will receive, or  
choose the chapter the DVD player  
plays back.  
• Some models of DVD player use the  
p buttons for both operating the fast  
forward/backward functions and for  
choosing the chapter. In this case, the  
253 buttons do not work.  
To return the multi-picture to one  
screen:  
Press the M button, press the 5  
buttons to choose one screen, and then  
press the a button.  
You cannot turn the TV on or off when the  
VCR/TV/DVD switch is set to the VCR or  
DVD position.  
When you turn the TV on or off, set the  
VCR/TV/DVD switch to the TV position.  
• Pressing the b button will also return  
the display to one screen.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Teletext function  
4 Choose a teletext page by pressing  
the p p buttons, number buttons  
or colour buttons  
VCR/TV/  
DVD  
To return to the TV mode:  
Press the b button or g (Text) button.  
• If you have trouble receiving teletext  
broadcasts, consult your local dealer or  
the teletext station.  
• The ZOOM function will not work in  
the TV and text mode or Text mode.  
• You cannot operate menus when  
viewing a teletext programme.  
• Language display depends on the  
country which was set on the  
COUNTRY menu. If characters on a  
Teletext programme do not appear  
properly, change the COUNTRY  
setting to other country’s. To change  
the COUNTRY setting, perform steps  
1 and 2 of the “AUTO PROGRAM”  
procedure on page 33 and then press  
the a button.  
Basic operation  
You can view three types of teletext  
broadcasts on the TV:  
FLOF (Fastext), TOP and WST.  
• TOP is not available when the  
COUNTRY setting is UNITED  
KINGDOM.  
1 Choose a TV channel with a teletext  
broadcast  
2 Set the VCR/TV/DVD switch to the  
TV position  
Using the List Mode  
You can store the numbers of your favourite  
teletext pages in memory and call them up  
quickly using the colour buttons.  
3 Press g (Text) button to display  
the teletext  
To store the page numbers:  
1 Press B button to go into the  
List mode  
Pressing g (Text) button changes the  
mode as follows:  
The page numbers you have stored are  
displayed at the bottom of the screen.  
2 Press a colour button to choose a  
position. Then press the number  
buttons to enter the page number  
TV mode  
TV and text mode  
Text mode  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Teletext function  
3 Press and hold down the A (Store)  
button  
Reveal  
Some teletext pages include hidden text  
(such as answers to a quiz).  
You can display the hidden text.  
The four page numbers blink white to  
show that they are stored in memory.  
To call up a stored page:  
Each time you press the E (Reveal)  
button, text is hidden or revealed  
1 Press the B button to enter the  
List mode  
2 Press a colour button having a  
stored page  
Size  
To exit the List mode:  
You can double the height of the teletext  
display.  
Press the B button again.  
Hold  
Press the F (Size) button  
You can hold a teletext page on the screen for  
as long as you want, even while several other  
teletext pages are being received.  
Press the C (Hold) button  
Hold indication  
Index  
To cancel the Hold function:  
Press C (Hold) button again.  
You can return to the index page instantly.  
Press the G (Index) button  
Returns to page 100 or a previously specified  
page.  
Sub-page  
Some teletext pages include sub-pages that  
are automatically displayed.  
1 Choose a teletext page that  
includes sub-pages  
Sub-page numbers that can be viewed are  
automatically displayed at the top of the  
screen.  
2 Press the 5 buttons to choose a  
sub-page number  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Teletext function  
Cancel  
You can search for a teletext page while  
watching TV.  
1 Press the number button to enter a  
page number, or press a colour  
button  
The TV searches for a teletext page.  
2 Press H (Cancel) button  
The TV programme appears. When the  
TV finds the teletext page, its page  
number appears in the upper left of the  
screen.  
3 Press H (Cancel) button to return  
to a teletext page when the page  
number is on the screen  
• The TV mode cannot be resumed by  
pressing the H (Cancel) button. To  
return to the TV mode press b.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
This TV has a number of functions you can  
operate using menus. To use all your TV’s  
functions, you need to understand the basic  
menu operating techniques fully.  
Types of menu  
PICTURE menu  
Choose to set the screen  
settings.  
D0106  
D0107  
D0108  
Buttons used to operate the menus  
SOUND menu  
Choose to set the sound settings.  
FEATURES menu  
Choose to set the sleep timer  
and child lock settings.  
SET UP menu  
Choose to edit the channels or  
set the display language  
settings.  
D0109  
The menu guide area can be made to appear  
and disappear for some menus.  
While the menu is displayed, press the h  
button to change between the guide area  
being displayed and not displayed.  
Basic operation  
1 Press the H button to display  
the menu bar  
>> 4:3 AUTO ASPECT  
PICTURE  
PANORAMIC  
REGULAR  
14:9 ZOOM  
D0105-EN  
2 Press the 5 buttons to choose  
the menu you want to use and then  
press the a button  
OK  
D0017-EN  
Guide area  
PICTURE  
D1105-EN  
Chosen  
menu  
Chosen  
menu name  
>> 4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
3 Press the 6 buttons to choose  
the item to be set, press the 5  
buttons to set the item, and then  
press the a button  
D1017-EN  
• The guide area for some menus will still  
be displayed even if the h button is  
pressed. This is not a fault.  
If there are sub-menus, use the 7  
buttons to operate them.  
• Press the b button to return to  
the previous menu.  
• Press the b or H button to exit  
from the menu.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE menu  
PICTURE  
COLOUR  
STANDARD  
PICTURE MODE  
CONTRAST  
BRIGHT  
SHARP  
COLOUR  
You can adjust the picture colour.  
2 :lighter  
HUE  
COLOUR TEMP.  
FEATURES  
3 : deeper  
COOL  
RESET  
HUE  
OK  
D0014-EN  
You can adjust the picture tint.  
2 :reddish  
3 : greenish  
• While the PICTURE menu is displayed,  
pressing the blue button will set the  
CONTRAST, BRIGHT, SHARP,  
COLOUR, HUE settings to their default  
settings.  
• You can change the HUE setting (picture  
hue) when the colour system is NTSC  
3.58, or NTSC 4.43.  
COLOUR TEMP.  
PICTURE MODE  
You can select one of three COLOUR  
TEMP. modes (three tones of white) to adjust  
the white balance of the picture. Since white  
is the colour which is used as a reference for  
all the other colours, changing the COLOUR  
TEMP. mode affects the appearance of all  
the other colours on the screen.  
You can choose one of three PICTURE  
MODEs to adjust the picture settings  
automatically.  
BRIGHT:  
Heightens contrast and sharpness.  
COOL:  
STANDARD:  
A bluish white. Using this mode when  
watching bright pictures allows you to enjoy  
a more vivid and bright picture.  
Standardizes picture adjustment.  
SOFT:  
Softens contrast and sharpness.  
NORMAL:  
The normal white colour.  
CONTRAST  
WARM:  
You can adjust the picture contrast.  
2 :lower  
3 : higher  
A reddish white. Using this mode when  
watching films allows you to enjoy colours  
that are characteristic of films.  
BRIGHT  
You can adjust the picture brightness.  
2 :darker  
3 : brighter  
SHARP  
You can adjust the picture sharpness.  
2 :softer  
3 : sharper  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE menu  
• The MAX setting is not suitable for high-  
quality pictures which contain very little  
noise.  
FEATURES  
Choose FEATURES and press the a or 3  
button to display the sub-menu.  
Super DigiPure  
The Super DigiPure function uses the latest  
in digital technology to give you a natural-  
looking picture. The Super DigiPure function  
includes the following two functions.  
> FEATURES  
DIGITAL VNR  
Super DigiPure  
MOVIE THEATRE  
Colour DigiPure  
COLOUR SYSTEM  
4:3 AUTO ASPECT  
AUTO(LOW)  
AUTO  
AUTO  
ON  
DigiPure function:  
This function helps to create a natural-  
looking picture by eliminating unnecessary  
edges from high-contrast and crisp images.  
For images with low-contrast, edges are  
added to produce a sharper, more detailed  
picture.  
You can choose from the three DigiPure  
function settings of AUTO, MIN and MAX.  
• If you set the DigiPure effect too high on  
a low-quality picture that contains a lot of  
noise, this may actually make the noise  
worse. We recommend you use the  
AUTO setting if you can.  
OK  
D1015-EN  
DIGITAL VNR  
The DIGITAL VNR function cuts down the  
amount of ‘noise’ (‘snow’ or interference) in  
the original picture.  
You can choose from the three DIGITAL  
VNR function settings of AUTO, MIN and  
MAX.  
AUTO(LOW)/AUTO(HIGH):  
The TV will automatically adjust the level of  
the DIGITAL VNR effect to match the  
amount of noise in the picture, giving you the  
best possible picture.  
• If you set the DIGITAL VNR effect too  
high it can make the picture less sharp. It is  
recommended you use the AUTO(LOW)  
setting if you can. If you set the DIGITAL  
VNR function to AUTO(LOW) but still  
notice some noise, change the setting from  
AUTO(LOW) to AUTO(HIGH).  
Picture motion compensation  
function:  
This function displays fast-moving pictures  
(for example, the players or ball in a football  
game) more smoothly and naturally on the  
screen.  
• The effect level of the picture motion  
compensation function cannot be  
changed. The effect level is the same no  
matter which of the AUTO, MIN or MAX  
settings is used.  
MIN:  
The level of the DIGITAL VNR effect is set  
to the minimum. If you set the DIGITAL  
VNR function to AUTO(LOW) but feel that  
the sharpness of the original picture has not  
been reproduced fully, change the setting  
from AUTO(LOW) to MIN.  
AUTO:  
The TV will automatically adjust the level of  
the DigiPure effect to match the amount of  
noise in the picture, giving the best possible  
picture.  
• The MIN setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
MAX:  
The level of the DIGITAL VNR effect is set  
to the maximum. If you set the DIGITAL  
VNR function to AUTO(HIGH) but still  
notice some noise, change the setting from  
AUTO(HIGH) to MAX.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE menu  
MIN:  
OFF:  
The level of DigiPure effect is set to the  
minimum. When you set the Super DigiPure  
function to AUTO and notice some noise,  
change the setting from AUTO to MIN.  
• The MIN setting is not suitable for high-  
quality pictures which contain very little  
noise.  
Colour DigiPure doesn't work. This gives a  
less clear picture than when this function is  
turned on.  
COLOUR SYSTEM  
The colour system is chosen automatically.  
However, if the picture is not clear or no  
colour appears, choose the colour system  
manually.  
MAX:  
The level of DigiPure effect is set to the  
maximum. If you set the Super DigiPure  
function to AUTO but feel that the original  
picture quality has not been reproduced fully,  
change the setting from AUTO to MAX.  
• The MAX setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
1 Choose COLOUR SYSTEM. Then  
press the a or 3 button  
The sub-menu of the COLOUR SYSTEM  
function appears.  
>> COLOUR SYSTEM  
MAIN  
SUB  
PAL  
AUTO  
OFF:  
The Super DigiPure function is turned off.  
MOVIE THEATRE  
OK  
The MOVIE THEATRE function displays a  
cinema film picture more smoothly and  
naturally on the screen.  
D0016-EN  
2 Press the 5 buttons to choose  
AUTO:  
MAIN or SUB  
The television automatically recognizes the  
type of signal and turns the function on and  
off.  
MAIN:  
You can change the colour system of the  
main-picture.  
SUB:  
You can change the colour system of the  
sub-picture.  
• Choose MAIN when a sub-picture is  
not displayed.  
ON:  
This function is turned on.  
OFF:  
This function is turned off.  
• The motion may appear unnatural when  
viewing images with the NTSC colour  
system. When the MOVIE THEATRE  
function is set to AUTO or ON, the  
motion may appear unnatural when  
viewing images with the NTSC colour  
system.  
3 Press the 6 buttons to choose  
the appropriate colour system.  
Then press the a button  
PAL:  
PAL system  
SECAM:  
SECAM system  
NTSC 3.58:  
NTSC 3.58 MHz system  
Colour DigiPure  
Makes the colour outline stand out and  
increases the sharpness giving a clearer  
picture.  
NTSC 4.43:  
NTSC 4.43 MHz system  
ON:  
Colour DigiPure works. Normally use with  
this function turned on.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE menu  
AUTO:  
This function detects a colour system  
from the input signal. You can only use  
this when you are viewing a picture from  
programme number PR 0 (AV), or an  
EXT terminal.  
• The AUTO function may not function  
properly if you have poor signal quality.  
If the picture is abnormal in the AUTO  
function, choose another colour system  
manually.  
• When in the Programme numbers PR 0  
(AV) to PR 99, you cannot choose NTSC  
3.58 or NTSC 4.43.  
SECAM cannot be chosen when the  
COUNTRY setting is UNITED  
KINGDOM.  
• “COLOUR SYSTEM” cannot be chosen  
when you are watching the EXT-4  
picture.  
4:3 AUTO ASPECT  
You can choose one of three ZOOM modes,  
REGULAR, PANORAMIC or 14:9 ZOOM,  
as the ZOOM mode for the normal picture  
(4:3 aspect ratio).  
1 Choose 4:3 AUTO ASPECT then  
press the a button  
>> 4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
OK  
D0017-EN  
2 Press the 6 buttons to choose a  
ZOOM mode  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOUND menu  
SOUND  
BALANCE  
STEREO/  
BASS  
TREBLE  
BALANCE  
HEADPHONE VOLUME  
3D CINEMA SOUND  
You can adjust the volume balance between  
the left and right speaker.  
2 :turn the left speaker’s volume level up.  
3 : turn the right speaker’s volume level up.  
OK  
HEADPHONE VOLUME  
D0019-EN  
Adjust the volume of the sub-picture sound  
which is heard through the headphones when  
set to 2-pictures multi.  
2 :Reduce volume  
3 : Increase volume  
• Functions in the “SOUND” menu other  
than “HEADPHONE VOLUME” work  
for the TV speakers. They do not work for  
the sound from the headphones.  
• When the headphones are connected and  
only one screen is displayed, only  
• When not set to 2-pictures multi, the  
headphone volume is adjusted with the  
r q (volume) buttons.  
“HEADPHONE VOLUME” can be used.  
STEREO / I • II  
When you are viewing a bilingual broadcast  
programme, you can choose the sound from  
Bilingual I (Sub I) or Bilingual II (Sub II). If  
you have poor reception on a stereo  
broadcast, you can change from stereo to  
mono sound so that you can hear the  
broadcast more clearly and easily.  
3D CINEMA SOUND  
Press the 3 button to set the 3D CINEMA  
SOUND effect when 3D CINEMA SOUND  
is set to ON or MONO.  
Choose 3D CINEMA SOUND. Then  
press the a or 3 button to display  
the sub-menu.  
s: Stereo sound  
v : mono sound  
> 3D CINEMA SOUND  
t : Bilingual I (sub I)  
u : Bilingual II (sub II)  
SURROUND  
BASS BOOST  
MID  
MID  
OK  
• The sound mode you can choose differs  
depending on the TV programme.  
• This function does not work in the EXT  
modes.  
D0111-EN  
SURROUND  
Adjust the surround effect.  
You can choose HIGH, MID or LOW.  
Choosing LOW will reduce the surround  
effect and choosing HIGH will increase the  
surround effect.  
BASS  
You can adjust the low tone of the sound.  
2 :weaker  
3 : strong  
BASS BOOST  
Adjust the bass sound.  
You can choose HIGH, MID or LOW.  
Choosing LOW will reduce the bass sound  
and choosing HIGH will increase the bass  
sound.  
TREBLE  
You can adjust the high tone of the sound.  
2 :weaker  
3 : strong  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES menu  
To cancel the SLEEP TIMER  
function:  
Press the 2 button to set the period of  
time to “OFF”.  
FEATURES  
SLEEP TIMER  
CHILD LOCK  
APPEARANCE  
BLUE BACK  
TYPE A  
ON  
CHILD LOCK  
OK  
When there is a TV channel you do not want  
your children to watch, you can use the  
CHILD LOCK function to lock out the TV  
channel. Even when a child chooses a  
programme number (PR) for a locked TV  
channel the screen will change to blue and  
display n (CHILD LOCK) so the TV channel  
cannot be viewed. Unless you enter a pre-set  
ID number by a special operation, the lock  
cannot be released and the child cannot view  
the TV channel.  
D0023-EN  
SLEEP TIMER  
You can set the TV to automatically turn off  
after a set period of time.  
1 Choose SLEEP TIMER. Then press  
the a or 3 button  
A Sub-menu of the SLEEP TIMER  
function appears.  
To set the CHILD LOCK function  
> SLEEP TIMER  
1 Choose CHILD LOCK, then press  
the 0 button  
0
120  
OFF  
“SET ID NO.” (ID number setting screen)  
appears.  
OK  
>> SET ID NO.  
D0024-EN  
0040  
2 Press the 5 buttons to set the  
period of time.  
OK  
Then press the a button  
You can set the period of time for up to  
120 minutes (2 hours) in 10 minute steps.  
• One minute before the SLEEP TIMER  
function turns off the TV, “GOOD  
NIGHT!” appears.  
• The SLEEP TIMER function cannot  
be used to turn off the TV’s main  
power.  
• When the SLEEP TIMER function is  
on, you can display the sub-menu of  
the SLEEP TIMER function again to  
confirm or change the remaining  
period of time of the SLEEP TIMER  
function. Press the a button to leave  
the menu after confirming or changing  
the remaining time.  
D0025-EN  
2 Set the ID number to your liking  
1 Press the 6 buttons to choose  
a number.  
2 Press the 5 buttons to move  
the cursor.  
3 Press the a button  
The Sub-menu of CHILD LOCK appears.  
> CHILD LOCK  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
LOCK  
OK  
D0026-EK  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES menu  
If you have forgotten the ID  
number:  
Perform step 1 of “To set the CHILD  
LOCK function”. After confirming the ID  
number, press the b button to exit the  
menu.  
4 Press the 6 buttons to choose a  
TV channel  
Every time you press the 6 buttons, the  
Programme number (PR) changes, and the  
picture of the TV channel registered in the  
Programme number (PR) is displayed on  
the screen.  
• Even if you reset the lock temporarily,  
it does not mean that the CHILD  
LOCK function set for the TV channel  
is cancelled. The next time anyone  
tries to view the TV channel, it will be  
locked again.  
• When you want to cancel the CHILD  
LOCK function, you must perform the  
operation “To set the CHILD LOCK  
function” again.  
5 Press the blue button and set the  
CHILD LOCK function.  
Then press the a button  
n (CHILD LOCK) appears and the TV  
channel is locked.  
To reset the CHILD LOCK function:  
Press the blue button again.  
n (CHILD LOCK) disappears.  
• To stop it being easy to choose the  
programme number (PR) of a locked  
TV channel, the programme number  
(PR) has been set so that it cannot be  
chosen with the 6 buttons or the  
buttons of the TV.  
To disable easy resetting of the CHILD  
LOCK function, the menu disappears if  
you choose the CHILD LOCK function  
and press the a button.  
• To stop it being easy to reset the lock,  
“ID NO.” (ID No. input screen) is set  
so that it cannot appear unless you  
To view a locked TV channel  
1 Choose a programme number (PR)  
of a locked TV channel with the  
number buttons or PR LIST  
The screen changes to blue and the n  
(CHILD LOCK) appears. You cannot  
view the TV channel.  
press the  
(Information) button.  
h
APPEARANCE  
Press the 5 button and choose the format  
in which the channel number is displayed  
from the three types: TYPE A, TYPE B and  
TYPE C.  
5
D0027-EN  
2 Press the  
(Information) button to  
h
display “ID NO.” (ID No. input  
screen)  
BLUE BACK  
5
You can set the TV to automatically change  
to a blue screen and mute the sound if the  
signal is weak or absent, or when there is no  
input from an external device.  
ID NO.  
:
D0028-EN  
3 Press the number buttons to enter  
the ID number  
ON:  
This function is turned on.  
The lock is temporarily released so you  
can view the TV channel.  
OFF:  
This function is turned off.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
SET UP  
EDIT/MANUAL  
AUTO PROGRAM  
EDIT/MANUAL  
LANGUAGE  
PICTURE TILT  
DECODER(EXT-2)  
EXT SETTING  
The EDIT/MANUAL functions are divided  
into two types:  
• editing the current programme numbers  
(PR) (EDIT functions); and  
ON  
• manually storing a TV channel you want  
to view on a particular programme  
number (PR) (MANUAL function).  
OK  
D0029-EN  
Here are the details about these functions:  
AUTO PROGRAM  
MOVE:  
This function changes the programme  
number (PR) of a TV channel.  
You can again perform the AUTO  
PROGRAM function TV channel automatic  
registration which was performed in the  
“Initial settings” (page 8).  
To receive SKY 1 you need a satellite tuner.  
You must have the satellite tuner set to SKY  
1 before starting the AUTO PROGRAM  
function.  
ID:  
This function registers a channel name (ID)  
to a TV channel.  
INSERT:  
This function adds a new TV channel in the  
current programme numbers (PR) list by  
using the CH number.  
• You cannot use the INSERT function if  
you do not know the channel number of a  
TV channel. Use the MANUAL function  
to register a TV channel in the programme  
number (PR).  
1 Choose AUTO PROGRAM, then  
press the a or 3 button  
The COUNTRY menu appears as a sub-  
menu of the AUTO PROGRAM function.  
There are two COUNTRY menus.  
Pressing the yellow button changes the  
COUNTRY menu as follows:  
DELETE:  
This function deletes a TV channel you do  
not want to list.  
> COUNTRY  
MANUAL:  
This function manually stores a new TV  
channel in a programme number (PR).  
START  
Caution  
OK  
MORE  
• Using the MOVE, DELETE or INSERT  
functions rewrites the current programme  
numbers (PR) list. Therefore, the  
> COUNTRY  
programme numbers (PR) of some of the  
TV channels will change.  
• Using the MANUAL function for a TV  
channel for which the CHILD LOCK  
function has been set cancels the CHILD  
LOCK function for that channel.  
START  
OK  
• Using the MANUAL function for a TV  
channel for which the DECODER (EXT-2)  
function has been set to ON returns the  
setting of the DECODER (EXT-2) function  
for that channel to OFF.  
• When a TV channel has already been  
registered in PR 99, using the INSERT  
function deletes that TV channel.  
MORE  
D0003-EN  
2 Press the 5 and 6 buttons to  
choose the country where you are  
3 Perform steps 5 and 6 of the “Initial  
settings” (page 9)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
• The CH/CC number is a number  
unique to the TV and corresponds to  
the channel number of a TV channel.  
For the relationship between a channel  
number and a CH/CC number, see  
“CH/CC NUMBER” on page 37.  
Basic operation  
1 Choose EDIT/MANUAL, then press  
the a or 3 button  
The EDIT menu appears.  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
MOVE  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
1 Press the 6 buttons to choose a  
TV channel  
Every time you press the 6 buttons, the  
programme number (PR) changes and the  
picture of the TV channel stored in the  
programme number (PR) appears on the  
screen.  
ID  
MANUAL  
OK  
MOVE  
INSERT DELETE  
D0038-EK  
2 Follow the description for the  
function you want to use  
2 Press the 3 button to start the  
MOVE function  
> EDIT  
3 Press the a button to complete  
the settings  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
CH 21  
The T-V LINK menu appears.  
BBC2 CH 22  
ITV  
CH4  
CH5  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
T-V LINK  
DOWNLOAD TV  
VCR  
OK  
STORE  
OK  
D0030-EK  
EXIT  
D0005-EN  
3 Press the 6 buttons to choose a  
If you do not have a T-V LINK  
compatible VCR connected:  
Press the b button to exit the T-V LINK  
menu.  
new programme number (PR)  
To cancel the MOVE function:  
Press the b button.  
The T-V LINK menu disappears.  
4 Press the 2 button to change the  
programme number (PR) of a TV  
channel to a new programme  
number (PR)  
If you have a T-V LINK compatible  
VCR connected to the EXT-2 terminal:  
Follow “Downloading the data to VCR” on  
page 11 to transmit the programme number  
(PR) data.  
• For programme number PR 0, “AV”  
appears in the programme numbers (PR)  
list.  
• An EXT terminal number does not appear  
in the programme numbers (PR) list.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
DELETE  
4 Press the blue button to display the  
ID LIST (channel name list)  
1 Press the 6 buttons to choose a  
TV channel  
> EDIT  
Every time you press the 6 buttons, the  
programme number (PR) changes and the  
picture of the TV channel stored in the  
programme number (PR) appears on the  
screen.  
CH  
ID LIST  
M6  
MBC  
MCM  
MDR  
MOVIE  
MTV  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
MTV3  
M
2 Press the yellow button to delete  
the TV channel  
OK  
D0033-EK  
The TV channel is deleted from the  
programme numbers (PR) list.  
5 Press the 6 buttons to choose  
the channel name (ID)  
ID  
To cancel the ID function:  
Press the b button.  
1 Press the 6 buttons to choose a  
TV channel  
Every time you press the 6 buttons, the  
programme number (PR) changes and the  
picture of the TV channel stored in the  
programme number (PR) appears on the  
screen.  
6 Press the a button to give a  
channel name (ID) to a TV channel  
• You can give your own unique channel  
name (ID) to the TV channel. When  
you have finished step 3, do not go to  
step 4. Press the 5 buttons to move  
the cursor, and press the 6 buttons  
to choose each character of the channel  
name (ID). Then press the a button  
to register the channel name (ID) to the  
TV channel.  
2 Press the red button to start the ID  
function  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
Before performing INSERT or  
MANUAL operation  
ID LIST  
OK  
• If you register the TV channel (SECAM-  
L system) from a French station, be sure  
to set the COUNTRY setting to  
FRANCE. If the COUNTRY setting is  
not set to FRANCE, perform steps 1 and 2  
of the “AUTO PROGRAM” (page 33)  
procedure and set the COUNTRY setting  
to FRANCE before pressing the a  
button.  
• A CH/CC number unique to this TV and  
corresponding to the Channel number of a  
TV channel is required. Find the  
corresponding CH/CC number from a  
table “CH/CC NUMBER” on page 37  
based on the Channel number of the TV  
channel.  
D0031-EK  
3 Press the 6 buttons to choose  
the first character of a channel  
name (ID) you want to give the TV  
channel  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
M
ID LIST  
OK  
D0032-EK  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
• When the COUNTRY setting is not  
FRANCE, use a two-digit CH/CC  
number. When the COUNTRY setting is  
FRANCE, use a three-digit CH/CC  
number.  
MANUAL  
1 Press the 6 buttons to choose a  
programme number (PR) for a new  
TV channel  
INSERT  
2 Press the blue button to activate  
the MANUAL function  
1 Press the 6 buttons to choose a  
programme number (PR) for which  
you will register a new TV channel  
> MANUAL  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
2 Press the green button and start  
the INSERT function  
> EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
SEARCH+  
FINE-  
OK  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
FINE+  
SEARCH-  
D0035-EK  
To cancel the MANUAL function:  
Press the b button.  
When the COUNTRY setting is  
IRELAND:  
OK  
0
9
CH/CC  
D0034-EK  
At the right side following the CH/CC  
number, the SYSTEM (broadcasting  
system) of the TV channel appears.  
To cancel the INSERT function:  
Press the b button.  
3 When the COUNTRY setting is  
UNITED KINGDOM:  
3 When the COUNTRY setting is  
UNITED KINGDOM:  
Press the number buttons to enter  
the remaining CH number  
• You cannot enter CC numbers.  
When the COUNTRY setting is  
IRELAND:  
Press the 6 buttons to choose  
“CH” or “CC”, then enter the  
remaining CH or CC number  
Continue to step 4  
When the COUNTRY setting is  
IRELAND:  
Press the 3 button to choose the  
SYSTEM (broadcasting system) for  
a TV channel you want to register  
If you do not know the correct  
broadcasting system, set the SYSTEM to  
“I”. If “I” is not correct, you will not hear  
the sound normally when the TV detects a  
TV channel. In this case, retry to set the  
SYSTEM correctly so that no problem  
arises.  
The TV shifts to registration mode.  
When the registration is completed, the  
picture of the TV channel appears on the  
screen.  
• The CH/CC number is a number given  
to each broadcast frequency that  
carries a TV channel. If the TV cannot  
detect the TV channel corresponding  
to the broadcast frequency indicated  
by the CH/CC number, a “no-signal”  
picture appears.  
4 Press the green or red button to  
search for a TV channel  
Scanning stops when the TV finds a TV  
channel. Then the TV channel is  
displayed.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
CH  
Channel  
E2, IR A  
E3, IR B  
E4, IR C  
E5, IR D  
E6, IR E  
E7, IR F  
E8, IR G  
E9  
CH  
Channel  
E40  
E41  
E42  
E43  
E44  
E45  
E46  
E47  
E48  
E49  
E50  
E51  
E52  
E53  
E54  
E55  
E56  
E57  
E58  
E59  
E60  
E61  
E62  
E63  
E64  
E65  
E66  
E67  
E68  
E69  
5 Press the green or red button  
repeatedly until the TV channel you  
want appears  
CH 02  
CH 03  
CH 04  
CH 05  
CH 06  
CH 07  
CH 08  
CH 09  
CH 10  
CH 11  
CH 12  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
CH 30  
CH 31  
CH 32  
CH 33  
CH 34  
CH 35  
CH 36  
CH 37  
CH 38  
CH 39  
CH 40  
CH 41  
CH 42  
CH 43  
CH 44  
CH 45  
CH 46  
CH 47  
CH 48  
CH 49  
CH 50  
CH 51  
CH 52  
CH 53  
CH 54  
CH 55  
CH 56  
CH 57  
CH 58  
CH 59  
CH 60  
CH 61  
CH 62  
CH 63  
CH 64  
CH 65  
CH 66  
CH 67  
CH 68  
CH 69  
If the TV channel reception is poor:  
Press the blue or yellow button to fine-  
tune the TV channel.  
E10, IR H  
E11, IR J  
E12  
6 Press the a button and register  
the TV channel to a Programme  
number (PR)  
E21  
E22  
E23  
The normal EDIT menu is resumed.  
E24  
E25  
CH/CC NUMBER  
E26  
E27  
• When you want to use the INSERT  
function on page 36, find the CH/CC  
number corresponding to the channel  
number of the TV channel from this table.  
If you want to know a particular TV  
channel’s channel menu, look in TV  
listings magazines or contact the  
broadcaster.  
• When the COUNTRY setting is UNITED  
KINGDOM, the CC number channels and  
the channels from CH/CC 02 to CH/CC 12  
cannot be received.  
E28  
E29  
E30  
E31  
E32  
E33  
E34  
E35  
E36  
E37  
E38  
E39  
CC  
Channel  
S1  
CC  
Channel  
S31  
S32  
S33  
S34  
S35  
S36  
S37  
S38  
S39  
S40  
S41  
X
CC 01  
CC 02  
CC 03  
CC 04  
CC 05  
CC 06  
CC 07  
CC 08  
CC 09  
CC 10  
CC 11  
CC 12  
CC 13  
CC 14  
CC 15  
CC 16  
CC 17  
CC 18  
CC 19  
CC 20  
CC 21  
CC 22  
CC 23  
CC 24  
CC 25  
CC 26  
CC 27  
CC 28  
CC 29  
CC 30  
CC 31  
CC 32  
CC 33  
CC 34  
CC 35  
CC 36  
CC 37  
CC 38  
CC 39  
CC 40  
CC 41  
CC 75  
CC 76  
CC 77  
CC 78  
CC 79  
S2  
S3  
S4  
S5  
S6  
S7  
S8  
S9  
S10  
S11  
S12  
S13  
S14  
S15  
S16  
S17  
S18  
S19  
S20  
S21  
S22  
S23  
S24  
S25  
S26  
S27  
S28  
S29  
S30  
Y
Z
Z+1  
Z+2  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
LANGUAGE  
DECODER (EXT-2)  
The LANGUAGE setting which was  
performed in the “Initial settings” (page 8)  
can be changed.  
If you have a decoder connected to a T-V  
LINK compatible VCR, which in turn is  
connected to the EXT-2 terminal, use the  
DECODER (EXT-2) function to unscramble  
the scrambled TV channels.  
1 Choose LANGUAGE, then press  
the a or 3 button  
1 Turn on the decoder power  
A sub-menu of the LANGUAGE function  
appears.  
2 Display the scrambled TV channel  
on the TV  
> LANGUAGE  
Even if the decoder is working, a  
scrambled picture appears.  
3 Display the SET UP menu and  
choose DECODER (EXT-2)  
OK  
SET UP  
D0002(E)-EN  
AUTO PROGRAM  
EDIT/MANUAL  
LANGUAGE  
PICTURE TILT  
DECODER(EXT-2)  
EXT SETTING  
2 Press the 5 and 6 buttons to  
choose a language. Then press the  
a button  
ON  
OK  
PICTURE TILT  
D0029-EN  
There are cases where the Earth’s magnetic  
field may make the picture tilt or make  
unnatural colours appear in the corner of the  
screen. If this happens, you can correct it.  
4 Press the 5 buttons to choose  
ON  
An unscrambled picture appears.  
1 Choose PICTURE TILT, then press  
the a or 3 button  
To cancel the DECODER (EXT-2)  
function:  
Press the 5 buttons to choose OFF.  
The sub-menu of the PICTURE TILT  
function appears.  
5 Press the a button to complete  
the setting  
>> PICTURE TILT  
The T-V LINK menu appears.  
T-V LINK  
DOWNLOAD TV  
VCR  
OK  
D0018-EN  
OK  
2 Press the 6 buttons until the  
picture becomes level. Then press  
the a button  
EXIT  
D0005-EN  
You can send the programme numbers  
data to a VCR with the T-V LINK  
function.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
6 Turn on the VCR, and then press  
the a button to transmit the data  
to VCR  
EXT SETTING  
1 Choose EXT SETTING, then press  
the a or 3 button  
The T-V LINK menu disappears once the  
data transmission ends.  
The EXT SETTING menu appears.  
7 If you have another TV channel  
capable of being unscrambled with  
a Decoder, repeat steps 2 to 6  
> EXT SETTING  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
If the DECODER (EXT-2) function has  
been set to “ON” but the TV channel  
cannot be unscrambled, check the  
following:  
EXT-4  
ID LIST  
• Has the decoder been connected to the  
VCR properly according to the VCR  
and decoder instruction manuals?  
• Has the decoder power been turned  
on?  
OK  
S-IN  
D0020-EN  
2 Follow the instructions for the  
function you want to use and  
operate the function  
• Can the TV channel be unscrambled  
with a decoder?  
S-IN:  
• Do you need to change the VCR  
settings in order to connect the  
decoder? Confirm that the VCR is set  
properly by rechecking the VCR  
instruction manual.  
You can enjoy the high-quality picture of  
the 2 S-VIDEO signal (Y/C signal).  
ID LIST:  
You can have a name for each of the  
devices connected for each EXT terminal.  
DUBBING:  
You can choose a signal source to be  
output from an EXT-2 terminal.  
S-IN (S-VIDEO input)  
You can connect a device (such as an S-VHS  
VCR) to enjoy the high-quality picture of the  
S-VIDEO signal (Y/C signal).  
Preparation:  
• First read the device’s instruction manual  
and “Additional preparation” on page 42  
to connect the device to the TV properly.  
Second, follow the device’s instruction  
manual to set the device so that it sends an  
S-VIDEO signal (Y/C signal) to the TV.  
• Do not set S-IN (S-VIDEO input) to an  
EXT terminal connected to a device  
which cannot output an S-VIDEO (Y/C  
signal). If it is set wrongly, a picture  
cannot appear.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
ID LIST  
1 Press the 5 or 6 buttons to  
You can store a name for each of the devices  
connected to each EXT terminal. Giving a  
name to an EXT terminal makes the EXT  
terminal number appear on the screen,  
together with its name.  
choose an EXT terminal  
> EXT SETTING  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
1 Press the 5 or 6 buttons to  
choose an EXT terminal  
EXT-4  
2 Press the blue button to display the  
name list (ID LIST)  
ID LIST  
OK  
S-IN  
> EXT SETTING  
D0110-EN  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
ID LIST  
VHS  
2 Press the yellow button and set the  
S-IN (S-VIDEO input).  
S-VHS  
DVC  
CAM  
SAT  
Then press the a button  
STB  
EXT-4  
GAME  
DVD  
DVR  
An S-IN (S-VIDEO input) mark is  
displayed. You can view an S-VIDEO  
signal (Y/C signal) instead of the regular  
video signal (composite signal).  
OK  
D0021-EN  
To cancel the S-IN (S-VIDEO input)  
setting:  
Press the yellow button and turn off S-IN (S-  
VIDEO input) mark. The regular video  
signal (composite signal) pictures are  
resumed.  
3 Press the 6 buttons to choose a  
name. Then press the a button  
The ID LIST disappears and the name is  
assigned to the EXT terminal.  
• You cannot assign an EXT terminal  
name not found in the name list (ID  
LIST).  
• The EXT-1 terminal does not support S-  
VIDEO signal (Y/C signal) and you  
cannot set S-IN (S-VIDEO input) in the  
EXT-1 terminal.  
To erase a name assigned to the  
EXT terminal:  
Choose a blank space.  
• Setting S-IN (S-VIDEO input) changes  
the head character from “E” to “S”. When  
an EXT terminal receives a normal video  
signal, “E1”, “E2”, “E3” or “E4” appears  
on the display. This changes to “S2”, “S3”  
or “S5” when it receives an S-VIDEO  
signal.  
4 Press the a button to complete  
the setting  
• Even a device which can output an  
S-VIDEO signal (Y/C signal) may output  
a regular video signal (composite signal)  
depending on the device setting. If a  
picture cannot appear because the S-IN  
(S-VIDEO input) setting has been made,  
read the device instruction manual  
carefully again to check for the device  
settings.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP menu  
TV:  
DUBBING  
The picture and sound of the TV channel  
you are currently viewing are output from  
the EXT-2 terminal.  
You can choose a signal source to be output  
from the EXT-2 terminal.  
You can do this with the output signals of the  
devices connected to other EXT terminals, or  
with the picture and sound from a TV  
channel you are currently viewing.  
• During dubbing, you cannot turn off  
the TV. Turning off the TV also turns  
off the output from the EXT-2  
terminal.  
1 Press the 5 buttons to choose  
• When you choose an EXT terminal as  
an output, you can view a TV  
programme or a picture from the other  
EXT terminal while dubbing the  
picture from a device connected to the  
EXT terminal onto a VCR connected  
to the EXT-2 terminal.  
the arrow from the menu  
> EXT SETTING  
EXT-1  
EXT-3  
EXT-5  
TV  
DUBBING  
EXT-2  
EXT-4  
• The RGB signals from TV games  
cannot be output. Teletext programmes  
cannot be output.  
OK  
D0022-EN  
2 Press the 6 buttons to choose an  
EXT terminal or TV.  
Then press the a button  
The arrow in the menu represents a signal  
flow. The left side of the arrow shows a  
signal source output from the EXT-2  
terminal.  
EXT-1/EXT-3/EXT-5:  
The output signal of the device connected  
to an EXT terminal passes through the TV  
and is output from the EXT-2 terminal.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
Connecting external equipment  
Connect the equipment to the TV, making  
the correct rear panel and front panel  
connections.  
1 VCR (composite signal)  
2 VCR (composite signal/S-VIDEO signal)  
3 T-V LINK compatible VCR (composite  
signal/S-VIDEO signal)  
4 Decoder  
5 DVD player (composite signal/S-VIDEO  
signal)  
Before connecting anything:  
• Read the manuals that came with the  
equipment.  
Depending on the equipment, the  
connection method may be different from  
the diagram. Also, the equipment settings  
may need to change depending on the  
connection method.  
6 DVD player (composite signal/RGB  
signal)  
7 DVD player (component video signals;  
Pr/Pb/Y)  
8 TV game (composite signal/RGB signal)  
9 TV game (composite signal/S-VIDEO  
signal)  
0 Headphones  
- Camcorder (composite signal/S-VIDEO  
signal)  
= SCART cable  
~ Audio cable  
! Video cable  
@ S-VIDEO cable  
# Component cable  
• Turn off all the equipment including the  
TV.  
• The “Specifications” on the back cover  
give the details of the EXT terminals. If  
you are connecting equipment not listed  
in the following connection diagram, see  
the table to choose the best EXT terminal.  
• Connecting cables are not supplied.  
HV-36P38SJE  
Front of the TV  
S
L
R
P
E
X
T
-
5
S
L
R
P
EXT-5  
Back of the TV  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
HV-32P37SJE/HV-28P37SJE  
Back of the TV  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT  
-2  
S
S
R
P
E
X
T
L
EXT-3  
5
S
R
L
A
U
D
I
O
O
U
T
R
S
E
X
T
P
L
5
R
Back of the TV  
EXT-  
4
EXT-1  
Y
Pb  
Pr  
L
EXT-2  
S
R
EXT-3  
S
L
AUDIO OUT  
R
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
Equipment which can output the  
S-VIDEO signal (Y/C signal) such  
as an S-VHS VCR  
TV output from the EXT-1 terminal  
The video/sound signal of a TV channel you  
are viewing is always output from the EXT-1  
terminal.  
Connect the equipment to an EXT terminal  
(but not the EXT-1 terminal).  
• Changing over a programme number (PR)  
also changes over the TV output from the  
EXT-1 terminal.  
• The video/sound signal from an EXT  
terminal cannot be output.  
You can choose between an S-VIDEO signal  
(Y/C signal) and a regular video signal  
(composite signal). For details of how to  
operate the equipment, see “S-IN (S-VIDEO  
input)” on page 39.  
• Teletext programmes cannot be output.  
Connecting speakers/amplifier  
While referring to the audio equipment  
connection diagram, connect the audio  
equipment you want to the TV.  
T-V LINK compatible VCR  
Be sure to connect the T-V LINK compatible  
VCR to the EXT-2 terminal. If not, the T-V  
LINK function will not work properly.  
• When connecting a T-V LINK compatible  
VCR to the EXT-2 terminal, be sure to  
connect the decoder to the VCR. If not,  
the T-V LINK function may not work  
properly. After you have stored TV  
You can use external front speakers to listen  
to the TV sound instead of the TV speakers.  
Before connecting anything:  
• Read the manuals provided with the  
amplifier and speakers.  
channels in the programme numbers (PR)  
list, set the DECODER (EXT-2) function  
for the programme number (PR) to ON to  
unscramble a scrambled TV channel. For  
details, see “EXT SETTING” on page 39.  
• Turn the TV and amplifier off.  
• To prevent magnetism from the speakers  
adversely effecting the TV screen, use  
magnetic-shielded speakers for the front  
speakers.  
• Note that connecting cables are not  
supplied.  
Connecting headphones  
Connect the headphones with a stereo mini-  
jack (3.5 mm diameter) to the headphone  
socket at the TV rear panel.  
Back of the TV  
L
R
• No sound comes from the TV speakers  
when the headphones are connected and  
only one screen is displayed.  
Video or sound signal output from  
the EXT-2 terminal  
1
2
Amplifier  
Front speakers (Magnetic-shielded type)  
You can change over the output of the video/  
sound signal from the EXT-2 terminal. This  
is useful when you want to dub the video/  
sound from another device onto the VCR  
connected to the EXT-2 terminal. For details  
on how to do this, see “DUBBING” on  
page 41.  
• The output from the AUDIO OUT  
terminal is not interrupted by headphone  
connection to the TV. You cannot cut the  
sound from the front speaker even if you  
connect a headphone to the TV.  
• Adjust the volume of the external  
speakers with the amplifier.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
If a problem arises while you are using the TV, please read this troubleshooting guide carefully  
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,  
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may  
think there is a problem with the TV itself.  
Important:  
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you  
have a question when you are operating a function, read the page(s) for that function carefully,  
not this troubleshooting guide.  
• If you follow the advice in this troubleshooting guide without any success, unplug the mains  
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to  
remove the rear cover of the TV.  
–Have the TV and aerial been connected  
properly?  
–Has the aerial cable been damaged?  
–Is the aerial pointing in the right  
direction?  
If you cannot turn on the TV  
• Is the mains plug connected to the mains  
outlet?  
• Is the power lamp lit? If not, press the  
main power button.  
–Is the aerial itself faulty?  
• Make sure you set the VCR/TV/DVD  
switch to the TV position. You cannot  
turn the TV on when the VCR/TV/DVD  
switch is set to the VCR or DVD position.  
• If the TV or aerial suffers interference  
from other equipment, stripes or noise  
may appear in the picture. Move any  
equipment such as an amplifier, personal  
computer, or a hair drier, that can cause  
interference away from your TV. Or try  
moving the TV. If the aerial suffers  
interference from a radio tower or high-  
voltage wire, please contact your local  
dealer.  
• If the TV suffers interference from signals  
reflecting from mountains or buildings,  
double-pictures (ghosting) will occur. Try  
to change the aerial’s direction or replace  
it with one with better directionality.  
• Are your COLOUR SYSTEM settings  
correct? Follow the description  
If you cannot turn off the TV  
• Make sure you set the VCR/TV/DVD  
switch to the TV position. You cannot  
turn the TV off when the VCR/TV/DVD  
switch is set to the VCR or DVD position.  
No picture or no sound  
• Have you chosen a TV channel with very  
poor reception? If so, the BLUE BACK  
function will be activated: the entire  
screen becomes blue, and the sound is  
muted. If you still want to view the TV  
channel, follow the description “BLUE  
BACK” on page 32 to change the BLUE  
BACK function setting to OFF.  
“COLOUR SYSTEM” on page 28 to try  
to solve the trouble.  
• Have the COLOUR and BRIGHT settings  
been adjusted properly? Follow the  
description “BRIGHT” and “COLOUR”  
on page 26 to try to adjust them properly.  
• Videotaping teletext is not recommended  
because it may not record correctly.  
• When a white and bright still image (such  
as a white dress) is displayed on the  
screen, the white part may look as if it is  
coloured. This is unavoidable due to the  
nature of the picture tube itself, and not  
due to a TV failure. When the picture  
disappears from the screen, the unnatural  
colours will also disappear.  
• If the SYSTEM setting for a TV channel  
is incorrect, it may prevent the sound  
from being issued. Follow the description  
“EDIT/MANUAL” on page 33 to use the  
MANUAL function to try to change the  
SYSTEM setting.  
Poor picture  
• If noise (snow) totally blocks out the  
picture, there may be a problem with the  
aerial or aerial cable. Check the following  
to try to solve the problem:  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
• When viewing images from commercially  
available video software products, or  
videos from videotapes which have been  
recorded improperly, the top of the image  
may be distorted. This is due to the  
condition of the video signal. There is  
nothing wrong with the TV.  
Other issues  
• When the SLEEP TIMER function  
operates, the TV is automatically turned  
off. If the TV suddenly turns off, try to  
press the # (standby) button to turn on  
the TV once again. If the TV goes back to  
normal, there is no problem.  
• Since this TV is designed to make full use  
of the resolution of the original video  
source, the motion may appear unnatural  
when the video source is input with 625p  
progressive-scanning component signals.  
If this occurs, change the output setting of  
the connected device to 625i interlace-  
scanning component signal output. See  
the instructions that came with the device  
for more information.  
• When the TV is receiving a wide-screen  
signal (WSS) or a signal from an external  
device affecting the screen size, the  
ZOOM mode automatically changes.  
When you want to resume the previous  
ZOOM mode, press the c button  
again.  
• If you bring magnetised equipment such  
as a speaker near to your TV, the picture  
may be warped or unnatural colours may  
appear at the corners of the screen. In this  
case, keep the equipment away from your  
TV. If speakers cause this to happen, use  
magnetically-shielded speakers instead.  
• A picture may be tilted due to the earth’s  
magnetic field. If so, use the “PICTURE  
TILT” on page 38 to correct the tilt.  
• It takes a short period of time from the  
time an operation such as changing  
channels is performed until an image is  
displayed. This is not a fault. This is the  
time needed for the image to stabilize  
before it can be displayed.  
Poor sound  
• Have you adjusted BASS or TREBLE  
properly? If not, follow the description  
“BASS” or“TREBLE” on page 30.  
• When TV channel reception is poor, it can  
be hard to hear stereo or bilingual sound.  
In this case, follow the description  
“STEREO / I • II” on page 30 to hear the  
sound more easily by changing it to a  
mono sound.  
If the TV does not respond to the  
remote control  
• Have the batteries of the remote control  
worn out? Follow the description “Putting  
the batteries into the remote control” on  
page 8 and replace them with new batteries.  
• Have you attempted to use the remote  
control from the sides or rear of the TV or  
from more than seven metres away from the  
TV? Use the remote control in front of your  
TV or from less than seven metres away.  
• When you are viewing a teletext  
programme, you cannot operate the  
menus. Press the b button to return to  
the ordinary TV programme, and then try  
operating the menus.  
• The TV may make a crackling sound due  
to a sudden change in temperature. The  
picture or sound may be normal. If you  
hear crackling sounds frequently while  
you are viewing the TV, there may be  
other causes. As a precaution, ask your  
service technician to inspect it.  
• Touching the screen may cause you to  
feel a slight electric shock due to its static  
electricity. This is unavoidable due to the  
construction of the picture tube. It is not a  
problem with the TV. You can rest  
assured that this static discharge is not  
harmful.  
• If the TV suddenly stops responding,  
press the main power button on the TV  
and turn off the main power. Press the  
main power button again to turn on the  
TV. If the TV returns to a normal state, it  
is not a failure.  
• When set to 2-pictures multi, adjust the  
headphone sound with HEADPHONE  
VOLUME in the SOUND menu.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
HV-36P38SJE  
When the COUNTRY setting is When the COUNTRY setting is  
UNITED KINGDOM IRELAND  
CCIR B/G, I, D/K, L  
PAL, SECAM  
COUNTRY setting  
Broadcasting systems  
Colour systems  
CCIR I  
PAL  
• The EXT terminals also support the • The EXT terminals also support the  
NTSC 3.58/4.43 MHz system.  
NTSC 3.58/4.43 MHz system.  
Channels and frequencies  
Sound-multiplex systems  
Teletext systems  
E21-E69  
IR A-J, E2-E12, E21-E69, S1-S41, X,  
Y, Z, Z+1, Z+2  
NICAM (B/G, I, D/K, L) system,  
A2 (B/G, D/K) system  
FLOF (Fastext), TOP,  
WST (World Standard System)  
NICAM (I) system  
FLOF (Fastext),  
WST (World Standard System)  
Power requirements  
Power consumption  
Picture tube size  
Audio output  
220 - 240 V AC, 50 Hz  
141 W (Standby: 2.0 W)  
Viewable area 86 cm (measured diagonally)  
Rated Power output: TV: 10 W + 10 W, Woofer: 18 W  
TV: 2 cm round × 2, (3 cm × 10 cm) oval × 4, Woofer: 16 cm round × 1  
Speakers  
EXT-1 terminal  
Euroconnector (21-pin, SCART)  
• Video input, Audio L/R inputs and RGB inputs are available.  
• TV broadcast outputs (Video and Audio L/R) are available.  
EXT-2 terminal  
Euroconnector (21-pin, SCART)  
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are  
available.  
• Video and Audio L/R outputs are available.  
• T-V LINK functions are available.  
EXT-3 terminal  
EXT-4 terminal  
Euroconnector (21-pin, SCART)  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
RCA connectors × 5  
• Component video (Pr, Pb, Y) inputs (625p, 525p, 1125i) and Audio L/R inputs  
are available.  
EXT-5 terminal  
RCA connectors × 3  
S-VIDEO connector × 1  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
AUDIO OUT terminal  
RCA connectors × 2  
• Audio L/R outputs are available.  
• Output level 0.5 Vrms.  
Headphone jack  
Dimensions (W × H × D)  
Weight  
Stereo mini-jack (3.5 mm in diameter)  
TV: 912 mm × 624 mm × 593 mm, Woofer: 435 mm × 230 mm × 120 mm  
TV: 70 kg, Woofer: 4 kg  
Accessories  
Remote control unit × 1 (RM-C1800), Woofer × 1  
AA/R6 dry cell battery × 2  
We may change the design and specifications without notice.  
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any  
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of  
the owners of copyright of the original picture sources, as this would be an infringement of  
copyright.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model  
HV-32P37SJE/HV-28P37SJE  
When the COUNTRY setting is  
UNITED KINGDOM  
When the COUNTRY setting is  
COUNTRY setting  
IRELAND  
Broadcasting systems  
Colour systems  
CCIR I  
PAL  
CCIR B/G, I, D/K, L  
PAL, SECAM  
• The EXT terminals also support the • The EXT terminals also support the  
NTSC 3.58/4.43 MHz system.  
NTSC 3.58/4.43 MHz system.  
Channels and frequencies  
Sound-multiplex systems  
Teletext systems  
E21-E69  
IR A-J, E2-E12, E21-E69, S1-S41, X,  
Y, Z, Z+1, Z+2  
NICAM (B/G, I, D/K, L) system,  
A2 (B/G, D/K) system  
FLOF (Fastext), TOP,  
WST (World Standard System)  
NICAM (I) system  
FLOF (Fastext),  
WST (World Standard System)  
Power requirements  
Power consumption  
220 - 240 V AC, 50 Hz  
HV-32P37SJE: 137 W (Standby: 2.0 W)  
HV-28P37SJE: 127 W (Standby: 2.0 W)  
Picture tube size  
HV-32P37SJE: Viewable area 76 cm (measured diagonally)  
HV-28P37SJE: Viewable area 66 cm (measured diagonally)  
Audio output  
Speakers  
Rated Power output: 10 W + 10 W  
(13 cm × 6.5 cm) oval × 2  
EXT-1 terminal  
Euroconnector (21-pin, SCART)  
• Video input, Audio L/R inputs and RGB inputs are available.  
• TV broadcast outputs (Video and Audio L/R) are available.  
EXT-2 terminal  
Euroconnector (21-pin, SCART)  
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are  
available.  
• Video and Audio L/R outputs are available.  
• T-V LINK functions are available.  
EXT-3 terminal  
EXT-4 terminal  
Euroconnector (21-pin, SCART)  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
RCA connectors × 5  
• Component video (Pr, Pb, Y) inputs (625p, 525p, 1125i) and Audio L/R inputs  
are available.  
EXT-5 terminal  
RCA connectors × 3  
S-VIDEO connector × 1  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
AUDIO OUT terminal  
RCA connectors × 2  
• Audio L/R outputs are available.  
• Output level 0.5 Vrms.  
Headphone jack  
Stereo mini-jack (3.5 mm in diameter)  
Dimensions (W × H × D)  
HV-32P37SJE: 948 mm × 562 mm × 550 mm  
HV-28P37SJE: 854 mm × 508 mm × 493 mm  
Weight  
HV-32P37SJE: 54.0 kg  
HV-28P37SJE: 38.0 kg  
Accessories  
Remote control unit × 1 (RM-C1800)  
AA/R6 dry cell battery × 2  
We may change the design and specifications without notice.  
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any  
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of  
the owners of copyright of the original picture sources, as this would be an infringement of  
copyright.  
LCT1536-001A-U  
0903-T-CR-JMUK  
© 2003 VICTOR COMPANY OF JAPAN, LIMITED  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Intel Telephone DG33TL User Manual
Jasco Satellite TV System TV24713 User Manual
Jenn Air Convection Oven SDV48600P User Manual
Johnson Controls Air Conditioner 13 145 SEER TCGD User Manual
Jonsered Lawn Mower Accessory LT2113 User Manual
JVC DVD Player XV N372S User Manual
JVC Portable CD Player RS WP1WT User Manual
Kenwood DVD Player DVF 3300 User Manual
Klipsch Speaker KL 7502 THX User Manual
KOI Portable Speaker Professional Powered Mini Monitor Speaker System User Manual