®
Stealthbox
I N S T A L L A T I O N G U I D E
START
HERE
for the
SB-T-SEQ/10W3
➔
➔
➔
(Fits 2001 and Up Toyota Sequoia)
STEP 1: Remove the driver’s side rear
STEP 2: Remove the driver’s side rear panel.
STEP 3: Grind off the plastic tabs which hold
storage area cover.
the pocket to the panel.
This Stealthbox is a product
which requires professional
installation skills and tools.
Please read this installation guide
thoroughly before beginning the
project. It will guide you step by
step through the installation. Several
of the steps in this process may
require two people to accomplish.
It is absolutely vital that the
enclosure be properly mounted to
the vehicle according to these
instructions. Failure to mount the
enclosure properly presents two
problems: 1)The sub-bass
performance will suffer due to the
movement of the enclosure caused
by the force exerted by the
woofer(s) and 2) A loose enclosure
presents a serious safety hazard in
the event of a collision or sudden
deceleration.
➔
➔
➔
STEP 4: Remove the pocket from the panel.
STEP 5: Create a notch in the side panel as
shown in the picture.
STEP 6: Create a second notch in the side
panel as shown in the picture.
Please enjoy your JL Audio
Stealthbox responsibly.
➔
Continued on Page 2 ➔
SB-T-SEQ/10W3v2-D2, JL AUDIO, Inc 2002
Page 1
Sheet SKU#011111 Revision 10/30/02
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Page 2
➔
➔
➔
➔
STEP 15: Adjusting the Socket Set Cup
Screw so that the proper length is exposed
(the exposed end of the rod is slotted to
accept a flat-blade screw driver to be used
when adjusting the rod’s position). Place the
3/8” flat washer, 3/8” lock washer and
3/8”bolt, in that order, on the threaded rod.
Do not fully tighten.
STEP 17: Fully tighten the bolt on the top of
the enclosure and the nut on the threaded
rod on the bottom of the enclosure to secure
the enclosure.
STEP 18: Reinstall the factory side panel.
STEP 19: Attach the supplied grill to the
factory side panel.
CONGRATULATIONS!
INSTALL COMPLETE.
Included Hardware:
(2) 1/4" Flat Washer
(2) 1/4" Lock Washer
(1) 1/4” U-Nut
(1) 3/8” Split Lock Washer
(1) 3/8” x 1-1/4” Fender Washer
(1) 3/8” x 2 1/4” Socket Cup Set Screw
(1) 3/8” Hex Nut
(2) 1/4” x 1” Bolt
(1) L-Bracket
(1) Grille
(1) 3” x 3”Wax Square
Mid/High Frequency Driver Information:
Specifications:
Enclosure Type: Acoustic Suspension (Sealed)
Driver Type: One JL AUDIO 10W3v2-D2 Subwoofer
Nominal Impedance: 4Ω
Cont. Power Handling: 300 Watts
Front Applicable JL Audio Products:
TR650-CSi & CXi
VR650-CSi
VR650-CSi & CXi
JLAudio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power the the Audio Stealthbox®.
Amp LP Filter
Mode/Slope
+12VDC
Ground Remote
Preamp Output Section
Output Mode
Bass Control
Infrasonic Filter
Amplifier Input Section
Input Voltage
Input Sens. Signal Sensing
Off/On
Rear Applicable JL Audio Products:
Full-Range/Low-Pass/High-Pass
Off/30Hz
+7
Off/12dB/24dB
Low/High
TR650-CXi,VR650-CXi
+3
+1
+10
+13
JL AUDIO 250/1
monoblock subwoofer amplifier
Left Ch.
Right Ch.
LF Boost (dB) Filter Freq. (Hz)
Left Ch.
Right Ch.
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
TR650-CXi
10369 N. Commerce Pkwy, Miramar, Florida 33025-392
Phone: 954.443.1100
Fax: 954.443.1111
SB-T-SEQ/10W3v2-D2, JL AUDIO, Inc 2002
Page 3
Sheet SKU#011111 Revision 10/30/02
Download from Www.Somanuals.com. All Manuals Search And Download.
|