™
jbl On TIME 200iD
AM/FM RADIO AND SPEAKER DOCK FOR iPod
iPod not included/iPod non inclus
UsEr GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
fcc sTaTEMEnT anD WarnInG
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
MODIFICATIONSNOTEXPRESSLYAPPROVEDBYTHEMANUFACTURERCOULDVOIDTHEUSER’SAUTHORITYTOOPERATETHEEQUIPMENTUNDERFCCRULES.
The normal function of the product may be disturbed by strong electromagnetic interference. If so, simply reset the product to resume normal operation by
following the instruction manual. In case the function could not resume, please use the product in another location.
CAUTION
WarnInG:TO PREVENT FIRE OR
ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
IMpOrTanT:
rIsK Of ElEcTrIc
sHOcK
—
DO nOT OpEn
THE APPROPRIATE ADAPTER MUST BE INSTALLED BEFORE
INSERTING YOUR iPod INTO THE JBL® PRODUCT. MAKE SURE
THAT THE CONNECTOR FOR THE iPod IS PROPERLY ALIGNED
WITH THE JBL PRODUCT’S CONNECTOR WHEN INSTALLING
YOUR iPod. FAILURE TO DO SO MAY CAUSE PERMANENT
DAMAGE TO THE CONNECTOR FOR THE iPod, RENDERING
THE iPod INOPERABLE.
THE LIGHTNING
FLASH AND
ARROWHEAD
WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU
TO DANGEROUS
VOLTAGE INSIDE
THE PRODUCT.
THE EXCLAMATION
POINT WITHIN
CAUTION: TO REDUCE
THE RISK OF SHOCK, DO
NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
THE TRIANGLE IS
A WARNING SIGN
ALERTING YOU
TO IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
WarnInG:THE APPARATUS SHOULD
NOT BE EXPOSED TO DRIPPING OR SPLASHING
AND NO OBJECTS FILLED WITH LIQUID, SUCH AS
VASES, SHOULD BE PLACED ON THE APPARATUS.
WWW.jbl.cOM
3
Download from Www.Somanuals.com. All Manuals Search And Download.
™
jbl On TIME 200iD
The JBL On Time™ 200ID high-performance loudspeaker dock and clock radio for iPod will revolutionize the way you listen to your radio,
use your iPod, and wake from a good night’s sleep.
The JBL On Time 200ID system is a revolution in time travel. Imagine waking up to music on your favorite station or your iPod, with no
more buzzer or bad radio reception. The compact time machine and sound center, when connected to your iPod, MP3 player or other
music source, produces clean, powerful sound while providing time-keeping, alarm and radio features. The system is the world’s first
time machine with an intuitive user interface that is easier than ever to navigate.
The JBL On Time 200ID loudspeaker dock has full ability to navigate your iPod via IR remote. Also, not only can you wake up to your
favorite radio station or song on your iPod, but with the multiple alarm setting option, you can set up to seven different alarms for “His”
and “Hers,” at whatever day or frequency needed.
OnEpOInT DEsIGn
The OnePoint connectors provide the connection to your computer. Connect the standard cable for iPod to the rear of
the JBL On Time 200ID unit, and every time you dock your iPod, you’ll have a connection for synchronizing.
EvErcHarGE TOpOlOGy
The JBL On Time 200ID speaker dock charges your iPod, even when it’s not connected to the computer or the system is off. The system’s
memory is maintained by a backup battery. Even with the power out, it will provide the alarm function.
cOE (cOMpUTEr-OpTIMIzED EqUalIzaTIOn)
The JBL On Time 200ID system equalization is computer-optimized to provide a rich, complete soundstage.
OcT (OpTIMIzED cOMprEssIOn TOpOlOGy)
The JBL On Time 200ID radio and loudspeaker dock utilizes a proprietary compression technology to ensure clean, accurate sound at
high output levels.
DIsplay
The large, backlit LCD enables easy viewing and menu navigation. Automatic dimming sets the correct brightness level in any
room environment.
4
jbl On TIME 200iD UsEr GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
UnpacKInG yOUr jbl On TIME™ 200iD
Carefully unpack your speaker system and identify all its components:
IR remote
FM antenna
JBL On Time™ 200ID
Adapters for iPod
Power supply
Audio cable
AM antenna
qUIcK sETUp InsTrUcTIOns
Choose the appropriate adapter for iPod and place it into the docking station. Then place your iPod into the adapter.
For backup memory, install three AAA batteries in the battery compartment underneath the unit.
Connect the external AM antenna for better reception.
Unwind the FM antenna and straighten the wire for the best reception.
Plug the power adapter into the “DC In” jack and then plug the adapter into a wall outlet.
If an additional audio source is used, connect the source to the “Aux In” jack.
•
•
•
•
•
•
FM ANT
AM ANT
AUX-IN
USB
DC 15V
AAA
A A A
AAA
Aux In
DC In
DC 15V
FM ANT
AM ANT
AUX-IN
USB
WWW.jbl.cOM
5
Download from Www.Somanuals.com. All Manuals Search And Download.
cOnTrOls
Setting the Clock
1. Press Menu/Up Level at any screen to display Top Menu (may require repeated presses, depending on which menu state the unit
was previously in).
2. Use Up/Down arrows to highlight Clock. Press Enter to confirm.
3. Use Up/Down arrows to highlight 12-hour or 24-hour format. Press Enter to confirm.
4. Use Up/Down arrows to set Hour. Press Enter to confirm. Minute field becomes highlighted.
5. Use Up/Down arrows to set Minutes. Press Enter to confirm. AM/PM field becomes highlighted.
6. Use Up/Down arrows to set Day of Week. Press Enter to confirm. The clock is set!
Note: During clock-setting, if there is no user input for 2 seconds, display will return to the Now Playing screen. Press any one of the Enter, Up/Down arrows, or
Menu/Up Level to return to setting selection.
Base Unit Control
Power
Navigation
Select Up
Volume Down
Volume Up
Alarm
Source
Menu/Up Level
Enter
Preset
Select Down
6
jbl On TIME 200iD UsEr GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Music
1. Press Source button to select the source (iPod, AM, FM, Aux).
2. Press “+” button to increase volume.
3. Press “–” button to decrease volume.
Radio Tuning
1. If AM or FM radio is already selected and playing, use Up/Down arrows to
tune frequency; hold either button and release to scan for the next station.
2. Otherwise, press Source until FM or AM is selected.
3. Tune to the desired frequency using Up/Down arrows; hold either button and
release to scan for the next station.
Power
Alarm
Source
Setting Presets
1. While listening to AM/FM radio, press and hold Preset for 2 seconds.
The Radio Preset screen will be displayed.
2. Use Up/Down arrows to select slot to store preset. Press Enter to confirm.
Preset is stored!
Preset
Select Up
Menu/Up Level
Enter
To Select a Preset for Listening
1. Press Preset once at any screen to display the Preset list.
2. Use Up/Down arrows to highlight Preset. Press Enter to confirm. Preset station will begin playing!
Select Down
WWW.jbl.cOM
7
Download from Www.Somanuals.com. All Manuals Search And Download.
cOnTrOls (cOnT.)
Alarm Setting†
1. Press Menu/Up Level at any screen to display Top Menu (may require repeated presses,
depending on which menu state the unit was previously in).
2. Use Up/Down arrows to highlight Alarm. Press Enter to confirm; or press Alarm to go directly to the Alarm menu.
3. Use Up/Down arrows to select an Alarm slot to edit. Press Enter to confirm. Hour field becomes highlighted.
4. Use Up/Down arrows to set Hour. Press Enter to confirm. Minute field becomes highlighted.
5. Use Up/Down arrows to set Minutes. Press Enter to confirm. AM/PM field becomes highlighted.
6. Use Up/Down arrows to set AM/PM. Press Enter to confirm.
7. Use Up/Down arrows to set Day of Week, Weekdays, Weekends, Everyday or One-Time. Press Enter to confirm.
8. Use Up/Down arrows to set Alarm source. Press Enter to confirm. Alarm is set!
Note: During alarm-setting, if there is no user input for 2 seconds, display will return to the Now Playing screen. Press any one of the
Enter, Up/Down arrows, or Menu/Up Level to return to setting selection.
Power
† Use this same procedure to modify a previously set Alarm.
Alarm
Source
To Enable/Disable a Set Alarm
1. Press Menu/Up Level at any screen to display the Top Menu (may require repeated presses,
depending on which menu state the unit was previously in).
Preset
Select Up
2. Use Up/Down arrows to highlight Alarm. Press Enter to confirm;
or press Alarm to go directly to the Alarm menu.
3. Use Up/Down arrows to highlight Alarm. Press Alarm to enable/disable the alarm.
Menu/Up Level
Enter
An icon will be displayed on the left when the alarm is enabled, and the alarm will sound at the set time.
Waking to the iPod
Select Down
1. Use the steps under Alarm Setting and choose “iPod” as the source.
2. On your iPod, choose the song you would like to awaken to and press Play.
3. Set the volume level on the JBL On Time™ 200ID unit.
4. Put your iPod to sleep by holding down the Play/Pause button (older iPod models may vary).
5. The JBL On Time 200ID system can be put to sleep by pressing the Power button.
Note: If you choose the last song on your iPod, please place the iPod in repeat mode, which will ensure that the iPod will continue playing past the last song.
8
jbl On TIME 200iD UsEr GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Contrast/Brightness
1. Press the Menu/Up Level button until you reach the Top Menu screen.
2. Use Up/Down arrows to select Display and press Enter.
3. Use Up/Down arrows to select Brightness or Contrast. Press Enter.
4. Adjust settings using Up/Down arrows.
Note: To set brightness to Auto, press the Down arrow until Auto is highlighted.
Languages/Region
1. Press the Menu/Up Level button until you reach the Top Menu screen.
2. Use Up/Down arrows to select Region and press Enter.
3. Use Up/Down arrows to select language. Press Enter.
4. Use Up/Down arrows to select radio band region type. Press Enter.
Sleep Timer
1. Press the Menu/Up Level button until you reach the Top Menu screen.
2. Use Up/Down arrows to select Sleep and press Enter.
3. Use Up/Down arrows to select minutes and press Enter.
4. The sleep timer is started and the unit will power off when the timer reaches zero.
Snooze Timer Set
1. Press and hold the Snooze button for 3 seconds until you reach the Set Snooze Timer screen.
2. Use Up/Down arrows to select minutes and press Enter.
3. Snooze feature will use this value the next time it is activated.
WWW.jbl.cOM
9
Download from Www.Somanuals.com. All Manuals Search And Download.
rEMOTE navIGaTIOn
Button
Function
Turns main unit power on and off. Button is active in any menu state.
Preset the hot key. A single press brings up the preset screen from any menu. Repeated presses cycle through the preset list to the next
preset slot. Press and hold for 2 seconds when listening to the radio and the Now Playing screen is displayed, to store current radio station.
Volume Increase. Display changes to Volume screen. Increases volume level, turns Amps on if off, then increases volume. If in snooze
mode, cancels snooze mode and turns Amps on. Times out back to current menu.
Volume Decrease. If in snooze mode, no action. If not in snooze mode and Amps are on, displays changes to Volume screen and decreases
volume level. Times out back to current menu. Does not turn Amps on if off.
Enter or Selection Confirmation button. Confirms selection on any JBL On Time™ 200ID settings screen. If Now Playing screen is displayed,
returns to last-used menu screen.
Scroll Up/Tune Up. Moves highlighted box up on any JBL On Time 200ID menu setting screen. Increases digit value when setting Time
(hours and minutes) and Snooze Timer. In radio mode, manually increases tuning frequency; hold for Seek.
Scroll Down/Tune Down. Moves highlighted box down on any menu setting screen. Decreases digit value when setting Time (hours and
minutes) and Snooze Timer. In radio mode, manually decreases tuning frequency; hold for Seek.
Menu or Up Level button. If Now Playing screen is displayed, takes user to top-level menu screen. If in menu settings, steps up one level to
previous field or menu screen. Hold for 2 seconds to return to Now Playing screen.
Alarm hot key. Takes user to Alarms settings of menu tree. Button is active in any menu state. If alarm is sounding, turns alarm off. When
viewing alarms list, enables or disables selected alarm.
Snooze button and Snooze Timer setting hot key. If alarm is sounding, enables snooze mode. Press and hold for 2 seconds to enter Snooze
Timer setting screen.
Directly switches the JBL On Time 200ID source to iPod.
Sends Scroll Down command to iPod navigation. Works in iPod navigation only.
Sends Scroll Up command to iPod navigation. Works in iPod navigation only.
Cycles to next source. AM FM iPod AUX.
A single press starts sleep time countdown, using currently set timer. Press and hold for 2 seconds to enter Sleep Timer setting screen
(similar to base unit).
Next Track in iPod navigation only. Does not affect JBL On Time 200ID menu navigation or function.
Previous Track in iPod navigation only. Does not affect JBL On Time 200ID menu navigation or function.
Enter/Select in iPod navigation only. Does not affect JBL On Time 200ID menu navigation or function. Similar function to the center button
of the iPod.
Menu/Up Level in iPod navigation only. Does not affect JBL On Time 200ID menu navigation or function. Similar function to the Menu
button of the iPod.
Play/Pause/Mute button. When iPod is the active source, a single press sends the Play/Pause command to the iPod. When AM, FM or AUX
is the active source, a single press mutes audio/amp on the JBL On Time 200ID system.
10
jbl On TIME 200iD UsEr GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
jbl On TIME™ 200iD MEnU TrEE
Now Playing
(ON)
Now Playing
(Off)
Clock
Alarm
Display
Sleep
Region
HOT KEY POINT
(on remote)
12H
HR
24H
HR
Set Language:
English
Spanish
French
HOT KEY POINT
(on remote or base unit)
German
Italian
Dutch
AL1-AL7
Brightness
Contrast
Adjust
set sleep timer:
15-30-60
Min
Min
Select Alarm
A Selection command
displays setting
confirmation and returns
state to Top Level Menu
screen.
Enable/
Disable
am/pm
Adjust
Hr
set day
Min
Set Radio Type:
U.S.
Europe
A Selection command
returns state to display
menu screen.
Press and hold for 2 sec at
any point in menu structure,
to return to now Playing
screen.
MO/TU/
WED/TH/FR/
SA/SU/WK/
ED/WE
A Selection command
displays setting
confirmation and returns
state to Top Level Menu
screen.
Japan
AM
FM
iPod
Aux
Tone
A Selection command
displays setting
confirmation and returns
state to Top Level Menu
screen.
A Selection command
displays setting
confirmation and returns
state to Top Level Menu
screen.
WWW.jbl.cOM
11
Download from Www.Somanuals.com. All Manuals Search And Download.
jbl On TIME™ 200iD MEnU TrEE (cOnT.)
PRESET
HOT KEY POINT
(on remote or base unit)
SOURCE
HOT KEY POINT
(on remote or base unit)
SNOOZE
HOT KEY POINT
(hold button for 3 sec on base unit)
SNOOZE
set snooze
timer
Press and hold Preset
button while listening to
radio to store current
station. Select slot 1-10 and
press enter to store.
AM
FM
iPod
Aux
A Selection command
displays setting
confirmation and returns
state to Top Level Menu
screen.
Preset 1-10
Select and
begin playing
preset station
12
jbl On TIME 200iD UsEr GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
spEcIfIcaTIOns
TrOUblEsHOOTInG
Jbl ON tIME™ 200iD
SOuND QuAlItY
Frequency Response: 70Hz – 20kHz
Symptom
Possible Problem
Solution
Note
Power Consumption: 30 Watts maximum
JBL On Time™ 200ID Transducer: Phoenix SE
1-3/4" (45mm) x 2 (full range per channel)
No sound from the
No power to the unit
Make sure the wall power outlet or power strip
has power. Make sure all switches for outlet/
power strip are on and that all switches for speaker
system are on.
Is the display on? If not,
power is not getting to
your JBL On Time 200ID;
try the solutions shown.
JBL On Time™ 200ID unit
Power: 12 Watts per satellite at 1% THD
Input Impedance: >5k Ohms
Incorrect source selection
Make sure the correct source is selected; choose
FM radio as a source. Turn up the volume. Check
the system with a known good source, such as your
iPod. Connect the Aux In cable to the headphone
jack on your iPod.
Signal-to-Noise Ratio: >80dB
Input Sensitivity: 350mV RMS for rated power output
Power (USA/Canada): 120 Volts, 60Hz AC
Power (Europe/UK): 220 – 230 Volts, 50Hz or 60Hz AC
Power (Japan): 100 Volts, 50Hz or 60Hz AC
Power (Australia): 240 Volts, 50Hz or 60Hz AC
UL/CUL/CE-Approved
No sound or weak signal from
the AM/FM radio
Bad reception from current location
Interference
Reposition your JBL On Time 200ID unit until you
find better reception.
If you are still getting a weak signal
from AM broadcasts, connect the
external AM antenna to the AM
antenna jack.
Check surrounding area for any possible
interference; wrap up any excess cables.
Sound comes from one
side/channel only
iPod or audio cable is not seated
properly
Make sure the iPod or Aux In cable is seated all the
way into the JBL On Time 200ID unit.
If you want to use a longer cable,
make sure it’s a 3.5mm mini-jack
stereo male-to-male cable.
Dimensions: 11-3/16" x 5-3/4" x 2-3/4"
(W x D x H) (284mm x 146mm x 70mm)
Distortion (static, crackling or
hissing sounds)
Noise may be caused by interference
from a monitor, cell phone or other
transmitting device
Turn monitor off to see whether noise is eliminated.
Move JBL On Time 200ID unit’s cables farther away
from monitor.
Weight: 1.8 lb (0.8kg)
JBL On Time 200ID unit is being over-
driven by an amplified audio source
Make sure the unit is connected to an appropriate
source device. Make sure all signal cables are
inserted snugly into receptacles.
Remote Battery: CR2025
Volume level may be too high
Check volume of source device; some devices
will distort the output signal if the volume is set to
maximum.
Too much bass or treble
Check the EQ setting on your iPod or
source device
We recommend that the source device EQ be set
to Flat or Off.
DiSPOSAL: Do not dispose of this
product as unsorted municipal
waste. Collection of such waste
separately for special treatment is
necessary.
iMPORTANT: Use UM4/AAA/LR03
alkaline-type nonrechargeable
batteries only.
JBL On Time 200ID unit emits a
loud hum or buzzing noise
Input cables are not plugged in properly
Check input cable connection.
Speaker system experiences
radio frequency interference
or picks up a radio station
Input cable may be picking up
interference
Wrap up excess input cable to make it as short
as possible.
Purchase a ferrite clamp and attach it over the
input cable; a clamp can be purchased at your local
electronics store.
WWW.jbl.cOM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TrOUblEsHOOTInG
ChARgINg AND SYNCINg
Symptom
Possible Problem
Solution
Note
iPod will not charge
Wrong adapter is used
Make sure correct adapter is used for your specific
iPod model.
The iPod is not making full contact with
the docking station
Make sure the iPod is seated securely into the
docking station.
iPod is not recognized by the
computer when docked into
the JBL On Time™ 200ID unit,
or there is an error in data
transfer
Third-party accessories may be conflict-
ing with the USB signal
Make sure you do not have the JBL On Time 200ID
unit connected to a USB hub; connect the unit
directly into the computer’s USB port.
Try connecting the USB cable to another port on the
back of the computer.
USB port is not supplying enough power
ClOCK SEt AND ClOCK MEMORY
Symptom
Possible Problem
Solution
Note
Clock is not set to correct time
Incomplete setup
Be sure to follow the clock setting procedure
through, to the end. A confirmation screen will be
displayed when set completely.
JBL On Time 200ID unit does
not retain memory settings
when there is a power outage,
or if the unit is unplugged
There are no batteries installed in
the unit
Make sure you install three AAA batteries in the
base of the JBL On Time 200ID unit.
Batteries may be low
If you have installed three AAA batteries, replace
them, as they may be defective.
14
jbl On TIME 200iD UsEr GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
WWW.jbl.cOM
15
Download from Www.Somanuals.com. All Manuals Search And Download.
JBL is a trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries.
JBL On Time is a trademark of Harman International Industries, Incorporated.
iPod, Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod” means that an electronic accessory has been designed to
connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
JBL est une marque commerciale de Harman International Industries, Incorporated, déposée aux États-Unis et/ou dans d’autres pays.
JBL On Time est une marque commerciale de Harman International Industries, Incorporated.
iPod, Apple et iTunes sont des marques commerciales de Apple Inc., déposées aux États-Unis et dans d’autres pays. « Made for iPod » signifie que le dispositif électronique a
été spécialement conçu pour se connecter à l’iPod et qu’il est certifié par le développeur comme conforme aux normes de performance Apple. Apple n’est pas responsable du
fonctionnement de ce dispositif ou de sa conformité avec les normes de sécurité ou réglementaires.
Harman Consumer Group, inc.
8500 Balboa Boulevard, Northridge, CA 91329 USA
516.255.4525 (USA only)
© 2008 Harman International Industries, Incorporated. All rights reserved. Tous droits réservés.
Document Number: 950-0232-001 REV05/2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|