EVOLUTION
Owner’s Manual
EVOLUTION ELLIPTICAL
Customer Service
1.800.750.IRON
1.800.750.4766
Ironman Fitness
4009 Distribution Drive
Suite 250
Garland, TX 75041
Model Name : EVO-1
Manufactured Date:
Serial Number :
Write down for future reference
315-00040
01-06 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
WARNING! Before using this unit or starting any exercise program, consult your physician. This is especially
important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer
or distributor assumes no responsibility for personal injury or property damage sustained by or through the use
of this product.
WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is
important to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
1. It is the owner's responsibility to ensure that all users of this unit have read the Owner's Manual and are
familiar with warnings and safety precautions.
2. This unit has a user maximum capacity of 300 pounds.
3. The unit should only be used on a level surface and is intended for indoor use only. The unit should not be
placed in a garage, patio, or near water and should never be used while you are wet. Ironman Fitness recom-
mends a mat be placed under the unit to protect floor or carpet and for easier cleaning.
4. Follow safety information in regards to plugging in your unit. Do not run the power cord underneath your
unit. Do not operate the unit with a damaged or frayed power cord.
5. Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the unit with
bare feet, sandals, socks or stockings.
6. Always examine your unit before using to ensure all parts are in working order.
7. Allow the unit to fully stop before dismounting.
8. Pets should never be allowed near the unit.
9. Do not leave children unsupervised near or on the unit.
10. Never operate the unit where oxygen is being administered, or where aerosol products are being used.
11. Never insert any object or body parts into any opening.
12. For safety and to prevent damage to your unit, no more than one person should use the unit at a time.
13. Always unplug the unit before cleaning and/or servicing. Service to your unit should only be performed by
an authorized service representative, unless authorized and/or instructed by the manufacturer.
14. Failure to follow these instructions will void the unit warranty.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Thank you for purchasing the EVOLUTION Elliptical! This quality product you have chosen was designed
to meet your needs for cardiovascular exercise. Before you start, please read the Owner's Manual and become
familiar with the operation of your new unit.
Remember to take the time to perform the stretching exercises provided to avoid injury.
If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate.
If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set pro-
grams or start an exercise program without first contacting and receiving approval from your physician.
To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. Keys
Fitness recommends a sealed water bottle for beverages consumed while using the unit.
Please review the following drawing below to familiarize yourself with the listed parts.
CONSOLE
WATER BOTTLE HOLDER
PULSE HANDLES
POWER
RECEPTACLE
TRANSPORT WHEEL
ADJUSTABLE FEET
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
INSTRUCTIONS FOR ASSEMBLY:
Unpack the box in a clear area. Check to make sure all components are present and in good condition.
Do not dispose of the packing material until the assembly is completed. Tools have been provided for you
to use when assembling this product.
Step 1
A) Attach the Foot Tube to the Plate and secure in place using three 3/8*20mm Hex Bolts and 3 Large
Washers.
B) Secure the Foot Tube to the Rails using four M8*15mm Button Screws and four Small Washers.
Figure 1
M8*15mm Button Screw
Small Washers
Plate
Rails
Large Washer
Foot Tube
3/8*20mm Hex Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 2
A) Insert Left Handlebar into the opening at the top of the left side on the Main Frame. Secure to the
Pivot Arm using a Small Washer and a M8*45mm Hex Bolt.
B) Slide two of the Cover Plates over the holes for the Short Screws.
C) Attach the Small Cover and secure in place using two Short Screws.
B) Slide a Grommet down the Left Handlebar and snap it onto the Main Frame.
Note: Make sure the Grommet is facing down as shown.
D) Repeat A, B, and C to complete the right side.
Figure 2
Main Frame
Left Handlebar
Grommet
M8*45mm Hex Bolt
Small Cover
Small Washer
Short Screw
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 3
A) Plug the Upper Console Cable, the two Pulse Wires, and the Grounding Wire into the back of the
Console. See Figure 3a
B) Secure the Console to the Console Tube and secure in place using four M5*12mm Screws and four
Small Washers.
Note: Make sure not to pinch the wire when installing the console.
C) Attach the Bottle Holder to the Console Tube using two Screws.
Upper Console Cable
Pulse Wire
Grounding Wire
Figure 3a
Console
Small Washer
M5*12mm Screw
Bottle Holder
Screw
Console Tube
Figure 3b
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 4
A) Plug the Upper Console Wire into the Lower Console Wire and slide the excess cable into the Main
Frame as you lower the Console Tube down.
B) Secure the Console Tube to the Main Frame using four Small Washers and 4 M8*15mm Button
Screws.
Figure 4
M8*15mm Button Screws
Small Washer
Console Tube
Upper Console Wire
Main Frame
Lower Console Wire
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 5:
A) Locate wheel kit and take out of box. Wheel kit will already include one Bolt (2D1E), two Washers
(0J4J), one Wheel (015W) and one Nut (0KMV). Tighten Nut if needed.
B) Attach wheel kit to the front of the frame. Tighten Bolt on the wheel kit.
Note: You will need a 17 mm wrench in order to complete this step.Wrench is provided.
Figure 5
Congratulations!
You have completed the assembly of your new EVOLUTION Elliptical!.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Instructions
Display Function
ꢀ
ꢀ
ꢀ
ꢀ
Data Window - TIME, SPEED, STRIDES, DISTANCE, CALORIES, PULSE, LEVEL, WATTS
Profile Window - Workout program profile and message.
Program Indicator - Indicate which program you are currently using.
Auto Scan Indicator - When this is lit, the DATA WINDOWS will automatically switch which
data is currently being displayed.
Data Windows
Time / Speed
Profile Window
Strides / Distance
Calories / Pulse
Program
Indicators
Level / Watts
Auto Scan
Indicator
Select / Scan
Program
Start / Enter
Stop / Reset
Time
Up / Down
Tension Level
Up / Down
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Instructions
Starting the Console -
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Plug in the power supply to power on the console.
Press START / ENTER key to go to the Quick Start Mode.
Press LEVEL UP and LEVEL DOWN for 2 sec. to go to the Service Mode.
Press TIME UP and TIME DOWN for 2 sec. to go to the Metric Unit Setting Mode.
Press the PROGRAM key to go to the Programming Mode.
After completing the program settings, press the START / ENTER to start the workout.
Stopping the Console -
ꢀ
ꢀ
ꢀ
The console will stop when the time counts down to zero.
Pressing the STOP / RESET key will stop the console time.
When you stop pedaling unit for 5 seconds the console will go into pause mode.
How to Reset the Console -
ꢀ
To reset entry data during the programming mode, press STOP / RESET key will clear the entry to
its default.
ꢀ
To reset console to the programming mode in the middle of a program, press STOP / RESET for 2
seconds during pause mode.
Workout Summary -
Once the program time has counted down to zero, the console will display all the last calculations
ꢀ
for 5 minutes presented as a workout summary. The workout summary will be terminated and
reset to its defaults if any key is pressed during the 5 minutes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Instructions
Key Description
START / ENTER - Press START / ENTER to start time counting or to confirm your setting while
programming the console.
SELECT / SCAN - Press SELECT / SCAN to swap the data window displays or press and hold
it for 2 seconds to alternate the displays automatically in 4 second intervals. The AUTO SCAN
indictor will be lit when the it is automatically shifting the console displays.
PROGRAM -- Press PROGRAM to select the workout program you choose. The PROGRAM
INDICATOR will be lit near the program you choose.
STOP / RESET -- Press STOP / RESET to stop the time from counting or hold it for 2 seconds to
reset your program time and the workout data to zero.
TIME UP / DOWN -- Use the TIME UP / DOWN to adjust the amount of time you wish to work-
out. The time range is from 0:00 to 99:59.
LEVEL UP / DOWN -- Use the LEVEL UP / DOWN to adjust the workout resistance. The resist-
ance range is from 1 to 16, sixteen being the hardest.
Programming Mode
1) Use TIME UP / DOWN to enter the amount of time you wish to workout. The manual profile will
appear on the PROFILE WINDOW and the setting time will be shown on the TIME WINDOW.
2) Press START / ENTER to confirm the workout time.
3) USE LEVEL UP / DOWN to enter the user weight. The message “LB” or “KG” will appear on
the PROFILE WINDOW and the setting weight will be shown on the TIME WINDOW.
4) Press START / ENTER to confirm the user weight.
5) Use PROGRAM key to select which workout program you intend to use.
6) Press START / ENTER and the console will start with the selected workout program and the
parameters you entered.
Quick Start Mode
1) Press the START / ENTER key only. The workout starts with the MANUAL program and has
a 30 minute default program time.
Using Running Mode
1) The console will display and update calculated workout data on each of the DATA WINDOWS.
2) The console will continue counting the program time until it has reached zero.
3) Use LEVEL UP / DOWN to adjust the workout resistance levels during the workout.
4) Use SELECT / SCAN to change the data that is being displayed in the windows or press and
hold SELECT / SCAN to autoscan the displays every 4 seconds.
5) You can change the workout program by pressing the PROGRAM key. Once the program is
selected it will begin at the beginning column but workout data windows will continue from
where they left off.
Sleeping Mode
1) The console will go into Sleeping Mode and shut off the display if there is no speed signal or key
pressed for 3 minutes.
2) Sleeping Mode will end if any key is press or pedaling begins.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Instructions
Console Service Mode
ꢀ
Display Scroll Testing will show on the PROFILE WINDOW and "0"…"9", "A"…"F" on the
DATA WINDOW, press any key to pass the testing.
ꢀ
ꢀ
Keypad Testing will show the key button test results in the PROFILE WINDOW.
Press and hold STOP / RESET key for 2 seconds to pass all the testing.
Metric Unit Setting Mode
1) Default : English
2) Use LEVEL UP / DOWN to change the metric unit display in the PROFILE WINDOW.
3) Press START / ENTER to confirm the settings.
4) Press STOP / RESET for 2 seconds to leave the Unit Setting Mode.
Error Message
ꢀ
The TIME window will show an "Err1" message whenever the brake motor was unable to move
to its target position within 2 seconds of powering on. If this happens the console will immedi-
ately disable any further key operations until the motor error disappears.
ꢀ
Turn the console power off and then on again to see the error message will disappear. If the error
message remains call Ironman Technical Service for more information.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving Instructions
CAUTION! TO REDUCE THE POSSIBILITY OF INJURY WHILE LIFTING, BEND YOUR LEGS AND
KEEP YOUR BACK STRAIGHT. AS YOU LEAN THE UNIT, LIFT USING YOUR LEGS, NOT YOUR
BACK.
Reach down and grab the rear Foot Tube assembly with both hands. Next, carefully tilt the unit up until it rolls
freely on the transport wheels. Using extreme caution, move the unit to the desired location. To set the unit
down, carefully lower unit onto Foot Tube assembly in a resting position. Do not attempt to move the unit
over an uneven or rough surface.
Foot Tube
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Your Heart Rate
Monitoring Your Heart Rate
To obtain the greatest cardiovascular benefits from your exercise workout, it is important to work within your
target heart rate zone. The American Heart Association (AHA) defines this target as 60%-75% percent of your
maximum heart rate.
Your maximum heart rate may be roughly calculated by subtracting your age from 220. Your maximum heart
rate and aerobic capacity naturally decreases as you age. This may vary from one person to another, but use
this number to find your approximate effective target zone. For example, the maximum heart rate for an aver-
age 40 year-old is 180 bpm. The target heart rate zone is 60%-75% of 180 or 108-135 bpm. See Fitness Safety
below.
Before beginning your workout, check your normal resting heart rate. Place your fingers lightly against your
neck, or against your wrist over the main artery. After finding your pulse, count the number of beats in 10 sec-
onds. Multiply the number of beats by six to determine your pulse rate per minute. We recommend taking your
heart rate at these times; at rest, after warming up, during your workout and two minutes into your cool down,
to accurately track your progress as it relates to better fitness.
During your first several months of exercising, the AHA recommends aiming for the lower part of the target
heart rate zone-60%, then gradually progressing up to 75%.
According to the AHA, exercising above 75% of your maximum heart rate may be too strenuous unless you
are in top physical condition. Exercising below 60% of your maximum will result in minimal cardiovascular
conditioning.
Check your pulse recovery rate – If your pulse is over 100 bpm five minutes after you stop exercising, or if
it’s higher than normal the morning after exercising, your exertion may have been too strenuous for your cur-
rent fitness level. Rest and reduce the intensity next time.
Fitness Safety The target heart rate chart indicates average rate zones for different ages. A variety of different
factors (including medication, emotional state, temperature and other conditions) can affect the target heart
rate zone that is best for you. Your physician or health care professional can help you determine the exercise
intensity that is appropriate for your age and condition.
(MHR) = Maximum Heart Rate
(THR) = Target Heart Rate
220 - age = maximum heart rate (MHR)
MHR x .60 = 60% of your maximum heart rate.
MHR x .75 = 75% of your maximum heart rate.
For example, if you are 30 years old, your calculations will be as follows:
220 - 30 = 190
190 x .60 = 114 (low end or 60% of MHR)
190 x .75 = 142 (high end or 75% of MHR)
30 year-old (THR) Target Heart Rate would be 114-142
See Heart Rate Table (on page 15) for additional calculations.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Your Heart Rate
TARGET HEART RATE ZONE
200
100%
195
190
185
180
175
Serious
athletic
training range
170
165
160
155
132
85%
170
150
166
146
162
143
157
139
153
135
Cardiovascular
conditioning
range
149
131
105
145
128
102
140
124
99
136
120
96
75%
Fat burning
range
116
93
60%
120
117
114
111
108
20 25 30 35
40 45 50 55 60 65
AGE
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
EXERCISE GUIDELINES
WARNING! Before beginning this or any exercise program, you should consult your physician. This is espe-
cially important for individuals over the age of 35 or individuals with pre-existing health problems.
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the mus-
cles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise
to warm up. The photos on this page show several forms of basic stretching you may perform before your
workouts. In order to achieve an adequate warm-up, perform each stretch three times.
TOE TOUCH STRETCH
Stand bending your knees slightly and slowly bend forward from your hips.
Allow your back and shoulders to relax as you reach down toward your toes
as far as possible. Hold for 15 counts, then relax. This will stretch your ham-
strings, back of knees, and back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite foot toward you and
rest it against the inner thigh of your extended leg. Reach toward your toes as
far as possible. Hold for 15 counts, then relax. This will stretch your ham-
strings, lower back, and groin.
CALF/ACHILLES STRETCH
With one leg in front of the other, reach forward and place your hands against
a wall. Keep your back leg straight and your back foot flat on the floor. Bend
your front leg, lean forward and move your hips toward the wall. Hold for 15
counts, then relax. To cause further stretching of the Achilles tendon, bend
your back leg as well. This will stretch your calves, Achilles tendons, and
ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and grasp one foot with
your other hand. Bring your heel as close to your buttocks as possible. Hold
for 15 counts, then relax. This will stretch your quadriceps and hip muscles.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees outward. Pull your
feet toward your groin area as far as possible. Hold for 15 counts, then relax.
This will stretch your quadriceps and hip muscles.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Parts List
EVO-1 Parts List Rev A
REF # PART #
0157 306-00282 WHEEL ASSEMBLY
DESCRIPTION
QTY REF # PART #
DESCRIPTION
QTY
4
4
2
1
1
1
2
5
4
2
2
2
1
2
2
1
2
4
2
1
2
1
4
1
2
1
1
1
1
1
4
2
2
1
1
1
2
3
4
4
4
4
4
1
2
1
2
2
4
4
2
3
2
2
2
4
4
4
2
1
2
4
2
4
0K98 302-00116 CR. RE. TRUSS HD. TAPPING SCREW M3.5*18-
0KCB 302-00117 CR. RE. TRUSS HD. TAPPING SCREW M5*12-25
0KDK 302-00111 CR. RE. PAN HD. SCREW M5*0.8-16MM
0KFZ 302-00112 CR. RE. PAN HD. SCREW M5*0.8-125MM
0KMY 302-00122 HEX. NUT M8*1.25 T=6.5MM
0KN1 302-00123 HEX. NUT M5*0.8 T=5MM
0KNE 302-00124 HEX. NUT M6*1.0 T=5MM
0KQY 302-00135 LOCK NUT M8*1.25 T=8MM
0KR9 302-00136 SCREW
0158 302-00095 FLAT WASHER 8.5*32MM
0165 319-00001 IDLER TENSION PLATE, A7E
2872 313-00065 GROUNDING CABLE, A7E
2909 311-00039 IDLER PULLEY ASSEMBLY, A7E
014X 306-00284 END CAP, A7E
2
2
1
5
1
2
2
4
4
2
1
2
2
1
1
1
1
4
1
1
2
2
2
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
014Y 310-00114 LEVELER, A7E
015A 302-00097 SHAFT BUSHING
015D 306-00293 STRAIN RELIEF
015E 330-00039 CENTER SHAFT, A7E
0KRK 302-00144 U-TYPE NUT M5-12MM
0KRV 302-00121 HEX. HD. NUT 3/8*26T
015H 319-00003 LINKAGE, A7E
015N 302-00146 SPRING
0ZLT 302-00143 WRENCH HEX. 5/16"-3 3/4"
2D1E 302-01171 BOLT, HEX HEAD, M10*55MM
21F1 306-00292 PLATE COVER
015P 319-00002 ADJUSTMENT PLATE, A7E
015Q 302-00136 SCREW
015R 311-00040 EDDY CURRENT BRAKE, A7E
015W 306-00291 TRANSPORTATION WHEEL
015Y 302-00096 SHAFT BUSHING
21F2 305-00162 LEFT COVER, EVO-1
21F3 305-00163 RIGHT COVER, EVO-1
21H4 314-00009 WARNING LABEL
016P 330-00041 CRANK ARM, A7E
21HN 310-00115 BREAK CABLE, A7E
016U 330-00040 CENTER SHAFT ASSEMBLY, A7E
017X 306-00290 RUBBER COVER
21MY 302-00106 FLAT WASHER 29*24*0.3MM
21R6 313-00071 TRANSFORMER, 600E
018A 314-00004 INSTRUCTION LABEL, 600E
018D 302-00098 FLAT WASHER 16*20-0.3MM
018E 302-00140 WRENCH
231P 313-00066 CONSOLE HARNESS, A7E
27FK 313-00067 CONTACT HR SENSOR, A7E
280K 313-00068 HAND PULSE HARNESS, A7E
28JH 310-00116 FOAM GRIP, A7E
018F 302-00135 LOCK NUT M8*1.25 T=8MM
01FD 314-00001 LEFT STICKER, 600E
28JV 323-00153 RAIL ASSEMBLY
01FE 314-00002 RIGHT STICKER, 600E
28JY 323-00145 LEFT HANDLEBAR ASSEMBLY
28JZ 323-00146 RIGHT MOVING HANDLE BAR ASSEMBLY
28K0 323-00154 REAR STABILIZER ASSEMBLY
28K5 323-00143 CONSOLE MAST
01HL 307-00055 MOTOR, 600E
01HU 313-00072 POWER SOCKET
01J8 313-00069 REED SWITCH, A7E
0HV4 331-00035 BALL BEARING 6203LLU( 600E)_
0HVP 331-00036 BALL BEARING 6004ZZ ( 600E)
0HWC 331-00037 BALL BEARING 6005Z ( 600E)
0J3Q 302-00141 WRENCH HEX. 5-70MM
0J3R 302-00142 WRENCH HEX. 6-83MM
0J4D 302-00099 FLAT WASHER 5*10-1MM
0J4E 302-00100 FLAT WASHER 6*13-1MM
0J4J 302-00101 FLAT WASHER 10*20-2MM
0J4P 302-00102 FLAT WASHER 8*16-1.4MM
0J57 302-00103 FLAT WASHER 8.2*19-1.4MM
0J5H 302-00138 WASHER 5.2*12-1.0MM
0J6C 302-00101 FLAT WASHER 10*20-2MM
0J7F 302-00105 FLAT WASHER 5/16*7/8-5/64
0JAG 302-00137 SCREW
28R6 323-00308 FRAME, REVISED FOR NEW TRANS WHEEL
28RQ 313-00070 WIRE HARNESS MAIN, A7E
28T4 306-00287 END CAP, A7E
28VS 310-00119 WATER BOTTLE, A7E
28ZR 323-00150 LEFT PIVOT ARM ASSEMBLY
28ZS 323-00149 RIGHT PIVOT ARM ASSEMBLY
28ZT 323-00147 LINKAGE ASSEMBLY
290A 313-00073 REED SWITCH ASSEMBLY
29B2 314-00016 LABEL SHROUD RIGHT, EVO-1
29B3 314-00017 LABEL SHROUD LEFT, EVO-1
29B4 314-00018 MEDALLION, EVO-1
2D3G 306-00622 PEDALS, EVO-1
2
2
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2D4R 328-00051 FOAM GRIPS, EVO-1
2DBE 311-00070 POLY V-BELT PULLET, EVO-1
2DDT 310-00170 WATER BOTTLE CAGE, EVO-1
2DDX 306-00623 END CAP, PEDAL TUBE ASSY, EVO-1
2DDW 306-00624 END CAP, REAR STABILIZER ASSY, EVO-1
2DDV 306-00625 END CAP, FRAME, EVO-1
2DE0 323-00329 PEDAL TUBE, EVO-1
0JED 302-00108 C-RING A-16
0JEG 302-00109 C-RING A-20
0JEH 302-00110 C-RING A-24
0JGQ 302-00147 PARALLEL KEY
0JUX 302-00125 HEX. SOC. HD. CAP BOLT M8*1.25-30MM
0JV0 302-00126 HEX. SOC. HD. CAP BOLT M8*1.25-45MM
0JV2 302-00127 HEX. SOC. HD. CAP BOLT M8*1.25-60MM
0JWJ 302-00128 HEX. SOC. HD. CAP BOLT 3/8"-16UNC-3/4inc
0JWP 302-00129 HEX. SOC. HD. CAP BOLT 3/8*16UNC-2INCH
0JWQ 302-00130 HEX. SOC. HD. CAP BOLT 3/8*16UNC-2"
0JWR 302-00120 HEX. HD. BOLT 3/8*16-3"
0JX8 302-00131 HEX. SOC. SET SCREW M6*1.0-8MM
0K01 302-00132 HEX. SOC. TRUSS HD. SCREW M8*1.25-15 MM
0K03 302-00133 HEX. SOC. TRUSS HD. SCREW M8*1.25-15MM
0K09 302-00134 HEX. SOC. TRUSS HD. SCREW M8*1.25-12MM
0K37 302-00118 CR.RE. PAN HD. SCREW & WASHER M5*0.8-16m
0K4A 302-00119 CR.RE. PAN HD. SCREW & WASHER M5*0.8-20
0K4R 302-00145 CR.-RE. TRUSS HD. SCREW M5*0.8-12MM
0K7H 302-00113 CR. RE. ROUND WASHER HD. SCREW M5*0.8-25
0K94 302-00115 CR. RE. TRUSS HD. TAPPING SCREW M5*12-16
2DEA 307-00089 CONSOLE ASSY, EVO-1
2DEN 323-00330 PEDAL LEVER, EVO-1
2DEQ 323-00331 LEFT PEDAL TUBE ASSY, EVO-1
2DET 323-00332 RIGHT PEDAL TUBE ASSY, EVO-1
2DEU 314-00006 SERIAL LABEL
2DEV 311-00071 POLY V-BELT PULLEY ASSY, EVO-1
2DFE 314-00019 SHROUD LABEL 2 LEFT, EVO-1
2DHG 310-00171 WATER BOTTLE ASSY, EVO-1
2DKB 314-00020 SHROUD LABEL 2 RIGHT, EVO-1
OJLE 311-00072 POLY V-BELT, EVO-1
01H5 310-00172 MAGNET SEAT W/MAGNET, EVO-1
0K4T 302-01189 CR. RE. ROUND WASHER HD. SCREW M5-20MM
0KMV 302-01190 HEX HEAD NUT M10*1.5
#
#
313-00144 POWER SUPPLY, 7.5VDC 1.8A
315-00040 OWNER'S MANUAL EVO-1
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Warranty Information
Residential Warranty
Frame: Lifetime
Parts: 2 Year
Labor: 1 Year
This Limited Warranty applies in the United States and Canada to products manufactured or distributed by
Ironman Fitness (“Ironman”) under the Ironman brand name. The warranty period to the original purchaser is
listed above in the table.
Ironman warrants that the Product you have purchased for use from Ironman or from an authorized Ironman
reseller is free from defects in materials or workmanship under normal use during the warranty period. Your
sales receipt, showing the date of purchase of the Product, is your proof of purchase. This warranty only
extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product
from you. It excludes expendable parts (wear items). Wear items pertain to components that might need to be
replaced due to normal wear and tear. These items vary per product but will include pedal straps, seats, grips,
chains, bottom bracket assemblies, pads, etc. Please contact an Ironman customer service representative for
specifics on wear items. This Limited Warranty becomes VALID ONLY if the product is purchased through an
Ironman Fitness authorized dealer unless otherwise authorized by Ironman Fitness in writing.
During the warranty period Ironman will repair or replace (at Ironman’s option) the product if it becomes
defective, malfunctions, or otherwise fails to conform with this Limited Warranty under normal use. In repair-
ing the Product, Ironman may replace defective parts, or at the option of Ironman, serviceable used parts that
are equivalent to new parts in performance. All exchanged parts and Products replaced under this warranty
will become the property of Ironman. Ironman reserves the right to change manufacturers of any part to cover
any existing warranty.
This warranty DOES NOT COVER shipping charges, export taxes, custom duties and taxes, or any other
charges associated with transportation of the parts or Product.
To obtain warranty service, you must contact an Ironman authorized retailer, service technician or Ironman
Fitness at our phone number located in this manual. Any parts determined to be defective must be returned to
Ironman to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and
taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsi-
ble for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You
must present Ironman with proof-of-purchase documents (including the date of purchase). Any evidence of
alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.
This warranty does not extend to any product not purchased from Ironman or from an authorized Ironman
reseller. This Limited Warranty does not extend to any Product that has been damaged or rendered defective;
(a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Ironman; (c)
by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a
result of service by anyone other than Ironman, or an authorized Ironman warranty service provider. Product
on which the serial number has been defaced or removed is not eligible for warranty service. Should any
Product submitted for warranty service be found ineligible, an estimate of repair cost will be furnished and the
repair will be made if requested by you upon Ironman’s receipt of payment or acceptable arrangements for
payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, IRONMAN MAKES NO OTHER WAR-
RANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IRONMAN EXPRESSLY DISCLAIMS
ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES
THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY.
NEITHER IRONMAN NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO
YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary
from state to state. This is the only expressed warranty applicable to Ironman-branded products. Ironman nei-
ther assumes nor authorizes anyone to assume for it any other express warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO
REGISTER YOUR UNIT WITH IRONMAN FITNESS.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Service
1.800.750.IRON
1.800.750.4766
Ironman Fitness
4009 Distribution Drive
Suite 250
Garland, TX 75041
Ironman and M-dot are registered trademarks of the World Triathlon Corp., used here by permission.
Download from Www.Somanuals.com. All Manuals Search And Download.
|