Owner’s Operator and Maintenance Manual
Get-U-Up™ Lift
DEALER: This manual MUST be given to
the user of this device.
USER: BEFORE using this device, read this
manual and save for future reference.
For more information regarding
Invacare products, parts, and services,
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
TABLE OF CONTENTS
........................................................................................................................................................................6
Assembling the Lift.....................................................................................................................................8
Using the Sling.............................................................................................................................................8
Performing Maintenance...........................................................................................................................9
Introduction...............................................................................................................................................13
Operating the Lift.....................................................................................................................................14
Introduction...............................................................................................................................................17
Moving the Patient to a Commode......................................................................................................21
Transferring to a Wheelchair................................................................................................................22
Standing Procedure..................................................................................................................................24
Part No. 1148115
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
TABLE OF CONTENTS
Maintenance Safety Inspection Checklist............................................................................................27
Detecting Wear and Damage................................................................................................................29
Cleaning the Sling and the Lift...............................................................................................................29
REGISTER YOUR PRODUCT
The benefits of registering include:
1. Safeguarding your investment.
2. Ensuring long-term maintenance and servicing of your product.
3. Receiving updates with product information, maintenance tips and industry news.
Register ONLINE at warranty.invacare.com
Please have your model number and purchase date available to complete your registration.
Any registration information you submit will only be used by Invacare Corporation and protected
as required by applicable laws and regulations.
4
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTES
SPECIAL NOTES
Signal words are used in this manual and apply to hazards or unsafe practices which
could result in personal injury or property damage. Refer to the table below for
definitions of the signal words.
SIGNAL WORD
MEANING
Danger indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
DANGER
Warning indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
WARNING
CAUTION
Caution indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO
CHANGE WITHOUT NOTICE.
Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use.
Contact dealer/carrier for further instruction.
MAINTENANCE
Maintenance MUST be performed ONLY by qualified personnel.
Part No. 1148115
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL LOCATIONS
LABEL LOCATIONS
WARNING - ALWAYS be
aware of the lift arms.
Injury to the patient and/or
assistant may occur.
OPERATION OF THE PATIENT LIFT
The mast (C) includes the steering handles used to
move and guide the lift. The mast is supported in a
socket in the rear center of the base with casters (A).
For transporting the lift in a vehicle, the mast, boom and
pump assembly may be lifted from the base socket for
convenient storage. Each time the mast is returned to
the socket of the base, care should be used to push the
mast as far as possible down into the socket. Rotate
the mast slightly until it locks in the center position. The
bottom of the mast tube is grooved on either side, and
those grooves seat on tabs in the base socket to
prevent any rotation of the mast during the lift
procedure. Secure the mast to the base by securely
tightening the screw located at the rear of the base.
WARNING - ALWAYS be
aware of the footrest,
Refer to the Patient Sling owner’s manual for complete
lifting preparation information.
especially
the
patient’s
The horn (D) is made with knobs on both sides and in
the center to accept the sling that supports the patient
during lift.
Serial
Number
position on the footrest.
Injury to the patient and/or
assistant may occur.
There are two controls on the pump assembly (F), which
are the pump handle (G) and the control valve (H). With
the control valve closed, the pump handle is moved up
and down with slow strokes of even pressure to raise
the horn. A patient in a sling attached to the horn would
be elevated by this operation. The horn is lowered by
opening the control valve and moving the control valve
away from the pump handle. A safety gate is part of the
hydraulic system that prevents sudden lowering of the
horn regardless of how far the control valve is opened.
The knee pad (E) can be adjusted for patient support
and comfort. Pull both adjustment pins outward at the
same time to move the knee pad to the desired
position. Make sure adjustment pins are engaged.
Serial
Number
D
G
C
H
F
B
A
E
I
To raise the footplate (I), position the knee pad (E) in the
highest setting. When the footplate is up, the knee pad
can be adjusted to the desired position.
WARNING: For maximum stability and patient
safety, operate this lift with the base legs in
maximum open position and locked when
lifting a patient.
The shifter handle (B) is used to open the legs of the
base for stability before lifting a patient. The base legs
should be locked in the maximum open position at all
times when a patient is on the lift.
To open the base legs, grasp the shifter handle in one
hand, and place the opposite hand on the steering
handle of the mast for balance. Move the handle to
your right to release the lock pin then bring the handle
towards you in a complete half-circle. The lock pin
should insert into a hole in the plate to lock the legs in
full open position and the shifter handle should once
again be vertical. To close the legs to a narrow position
for storage, reverse the above procedure. If the shifter
handle is not vertical (straight up and down), the lock
pin is not seated in place.
Rev. A
1148135
6
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPICAL PRODUCT PARAMETERS
TYPICAL PRODUCT PARAMETERS
HEIGHT AT SLING
HOOK-UP - MAX.
65.7 inches
HEIGHT AT SLING
HOOK-UP - MIN.
36 inches
37 inches
BASE WIDTH OPEN
BASE WIDTH CLOSED
BASE HEIGHT (CLEARANCE)
BASE LENGTH
23 inches
4.5 inches
40.5 inches
45 inches
OVERALL HEIGHT
OVERALL LENGTH
OVERALL WIDTH
44 inches
23 inches
CASTER SIZE (REAR/FRONT)
SLING OPTIONS
5 inches / 3 inches
Standing or Transport
Polyester
SLING MATERIAL
STANDING SLING
WIDTH
36 inches
13 inches
LENGTH
TRANSPORT SLING
WIDTH
38.5 inches
36 inches
LENGTH
WEIGHT CAPACITY
WEIGHT IN CARTON
350 lbs
100 lbs
88 lbs
WEIGHT OUT OF CARTON
Part No. 1148115
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
SECTION 1—GENERAL GUIDELINES
ꢀ WARNING
SECTION 1 - GENERAL GUIDELINES contains important information for the safe
operation and use of this product.
DO NOT move a person suspended in a sling any distance. The Invacare lift is NOT
a transport device. It is intended to transfer an individual from one resting surface
to another (such as a bed to a wheelchair). Otherwise, injury or damage may occur.
Assembling the Lift
Check all parts for shipping damage before using. In case of damage, DO NOT use the
equipment. Contact the dealer for further instructions.
DO NOT overtighten the mounting hardware. This will damage the mounting brackets.
Using the Sling
ꢀ WARNING
Standing Slings - Individuals that use the standing sling MUST be able to support the
majority of their own weight, otherwise injury can occur. Before lifting the patient,
make sure the bottom edge of the standing sling is positioned on the lower back of
the patient and the patient's arms are outside the standing sling. The belt MUST be
snug, but comfortable on the patient, otherwise the patient can slide out of the sling
during transfer, possibly causing injury.
Transport Slings - Before lifting the patient, make sure the bottom edge of the
transport sling is at the base of the spine and the patient's arms are outside the
transport sling. DO NOT raise the patient to a full standing position while using the
transport sling, otherwise injury may occur.
DO NOT use any kind of material (such as a plastic back incontinence pad or
seating cushion) between the patient and sling material that may cause the patient
to slide out of the sling during transferring.
ALWAYS use the color coded strap on the standing sling closest to the patient
while still maintaining patient stability and comfort. The shortest of the straps must
be at the back of patient for support. Using the long section will leave little or no
support for the patient's back. The loops of the sling are color coded and can be
used to place the patient in various positions. The colors make it easy to connect
both sides of the sling equally. Make sure that there is sufficient head support when
lifting a patient.
8
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
Use an Invacare sling that is recommended by the individual’s doctor, nurse or medical
assistant for the comfort and safety of the individual being lifted.
After each laundering (in accordance with instructions on the sling), inspect sling(s) for
wear, tears, and loose stitching.
Bleached, torn, cut, frayed, or broken slings are unsafe and could result in injury. Discard
immediately.
DO NOT alter slings.
Be sure to check the sling attachments each time the sling is removed and replaced, to
ensure that it is properly attached before the patient is removed from a stationary object
(bed, chair or commode).
Performing Maintenance
Regular maintenance of lifts and accessories is necessary to ensure proper operation.
After the first year of use, the attachment points and the mounting bracket of the lift arm
should be inspected every three months to determine the extent of wear. If these parts
become worn, replacement must be made.
DO NOT overtighten mounting hardware. This will damage mounting brackets.
Casters and axle bolts require inspections every six months to check for tightness, wear,
debris (such as hair and dirt) and that they roll free.
After the first twelve months of operation, inspect all pivot points and fasteners for wear.
If the metal is worn, the parts MUST be replaced. Make this inspection every six months
thereafter.
Top bolt must be checked at least every six months in conjunction with periodic
maintenance.
Part No. 1148115
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
SECTION 2— INSTALLATION
Assembling the Base, Mast and Horn Assembly
ꢀ WARNING
The mast may be removed from the base for storage or transporting. Each time the
mast is removed and returned to the socket of the base, the mast MUST be locked
into the socket of the base assembly.
1. Unpack the components from the shipping cartons.
2. Remove the locking screw from the bottom of the base.
3. Match the notch at the bottom of the mast assembly with the tabs inside the socket of
the base assembly.
4. Insert the mast assembly into the socket and onto the tabs.
5. Attempt to turn the mast assembly.
NOTE: If the mast does not turn, the mast is centered and locked in place.
6. Insert the locking screw into the bottom of the base and tighten securely.
Notch
Mast
Locking
Screw
Socket
Tab
FIGURE 2.1 Assembling Mast to Base
7. Remove the shoulder bolt, steel washers, nylon washers, and locknut from the horn
mounting lugs at the top of the mast assembly.
8. Align the holes of the horn mounting lugs and the horn bushing.
9. Insert the shoulder bolt completely through the holes of the horn mounting lugs, horn
10
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
NOTE: Be sure that the shoulder bolt is completely through the holes of the mast assembly and horn
assembly, and they are not riding on the shoulder of the bolt. The nylon washers must sit between
the horn bushing and horn mounting lugs.
CAUTION
When assembled, the horn and mast assemblies MUST pivot easily.
10. Tighten the shoulder bolt and locknut. The locknut and shoulder bolt can be tightened
completely.
NOTE: The horn assembly will pivot easily if the mounting hardware is aligned properly when the
horn assembly is secured to the mast. To check for correct alignment of the hardware, use the Allen
wrench provided and turn the shoulder bolt by hand (it should rotate without a lot of force being
applied). If excessive force is necessary, the shoulder bolt is NOT aligned properly. Disassemble and
repeat assembly procedures until proper alignment is obtained.
11. To check for tightness of the locknut and shoulder bolt:
A. Raise the horn assembly.
B. Push the control handle away from the pump assembly.
C. If the horn assembly pivots easily, the locknut and shoulder bolt are not too tight.
D. If the horn assembly does not pivot easily or does not pivot at all, the locknut and
bolt are not aligned properly. Repeats steps 7 to 11.
12. Remove the shoulder bolt and locknut from the cylinder lugs on the horn assembly.
13. Align the holes of the cylinder lugs and the cylinder rod.
14. Insert the shoulder bolt completely through the holes.
15. Tighten the locknut and shoulder bolt.
Part No. 1148115
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Shoulder
Bolt
Top View of Mast Assembly
Cylinder Rod
Cylinder Lug
(1of 2)
Steel
Washer
Nylon
Washer
Horn
Mounting
Lug
Locknut
Nylon
Washer
(1of 2)
Locknut
Locknut
Horn
Bushing
Horn
Horn
Mounting
Lug
Nylon
Washer
Steel
Washer
Steel
Washer
Horn Lug
(1 of 2)
Shoulder
Bolt
Shoulder
Bolt
Steel
Washer
Mast Assembly
FIGURE 2.2 Mast Assembly
Base Shifter Handle Assembly
NOTE: For this procedure, refer to FIGURE 2.3.
1. Insert the base shifter handle into the cam lock assembly at the back of the base.
2. Align the holes of the shifter handle and cam lock assembly.
3. Tighten the thumbscrew to secure the shifter handle in place.
NOTE: This should prevent the base shifter handle from being removed.
Thumbscrew
Base Shifter
Handle
Cam Lock
Assembly
FIGURE 2.3 Base Shifter Handle Assembly
12
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE LIFT
SECTION 3—OPERATING THE LIFT
Introduction
ꢀ WARNING
DO NOT attempt any transfer of a patient without approval of the patient's
physician, nurse, or medical assistant. Thoroughly read the instructions in this
owner's manual, observe a trained team of experts performing the lifting
procedures and then perform the entire lift procedure several times with proper
supervision and a capable individual acting as a patient.
ONLY operate the lift with the legs of the lift in the maximum open position for
optimum stability and safety. If the patient is in a sling and it becomes necessary to
move through a narrow passage, close the legs of the stand up lift only as long as it
takes to move through the passage. When the stand up lift is through the passage,
return the legs to the maximum open position.
If it is necessary to close the legs to maneuver the stand up lift under a bed, close
the legs only as long as it takes to position the stand up lift over the patient and lift
the patient off the surface of the bed. When the legs of the stand up lift are no
longer under the bed, return the legs to the maximum open position.
Use common sense in all lifts.
Invacare slings and lift accessories are specifically designed to be used in conjunction
with Invacare lifts. Slings and accessories designed by other manufacturers are not
to be utilized as a component of Invacare’s lift system.
DO NOT exceed maximum weight limitation of the lift. The weight limitation for
the Get-U-Up Lift is 350 lbs.
ALWAYS keep hands, fingers, feet and toes clear of moving parts to avoid injury.
Invacare recommends that two assistants be used for all lifting preparation and
transferring to/from procedures; however, the stand up lift can be operated with one
assistant. The use of one assistant is based on the evaluation of the health care
professional for each individual case.
Part No. 1148115
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE LIFT
Operating the Lift
Opening/Closing the Legs of the Adjustable Base
NOTE: For this procedure, refer to FIGURE 3.1 on page 15.
The shifter handle is used to open/close the legs of the base for stability when lifting a
patient.
Opening
1. Stand at the rear of the lift and grasp the shifter handle in one‐hand and place the
opposite hand on the steering handle of the mast for balance. Refer to Details “A ” and
“B”.
2. Push the shifter handle to your right to release the lock pin from its mounting hole.
3. Turn the handle clockwise until you are able to secure the lock pin into the opposite
mounting hole to fully open the legs of the base. Refer to Detail “C”.
NOTE: The lock pin MUST insert into its mounting hole in the socket assembly to lock the legs in
the full open position. The shifter handle will be in the vertical position and parallel with the mast
assembly.
ꢀ WARNING
If the shifter handle is NOT vertical, the lock pin is NOT seated in the socket
assembly. DO NOT use the lift until the lock pin is properly seated and locked in
place or injury and/or damage may occur.
Closing
1. Stand at the rear of the lift and grasp the shifter handle in one‐hand.
2. Place the opposite hand on the steering handle of the mast for balance. Refer to Details
“A” and “B”.
3. Push the shifter handle to your right to release the lock pin from its mounting hole.
4. Turn the handle counter‐clockwise until you are able to secure the lock pin into the
opposite mounting hole to close the legs of the base. Refer to Detail “C”.
14
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE LIFT
DETAIL “A”
Base
Closed
Shifter
Handle
Base
Open
Shifter
Handle
Mounting
Hole
Lock Pin
Locked
DETAIL “C”
DETAIL “B”
Steering
Handle
Steering
Handle
Shifter
Handle
Shifter
Handle
Mast
Mast
FIGURE 3.1 Opening the Legs of the Adjustable Base
Raising/Lowering Model Hydraulic Lifts
NOTE: For this procedure, refer to FIGURE 3.2 on page 16.
Raising the Lift
1. Ensure the control valve is in the closed position (control valve positioned towards
pump handle).
2. Move the pump handle up and down to raise the lift.
Lowering the Lift
1. Ensure the control valve is in the open position (control valve positioned away from
pump handle).
2. Move the pump handle up and down to lower the lift.
NOTE: The rate of descent is controlled by varying the amount that the control valve is opened.
NOTE: A safety gate is part of the hydraulic system that maintains a SLOW constant descent of
the boom regardless of how far the control valve is opened.
Part No. 1148115
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE LIFT
Pump
Handle
Pump Handle
Closed
Open
Control Valve
FIGURE 3.2 Raising Model Hydraulic Lifts
Adjusting the Knee Pad Height
ꢀ WARNING
Never adjust knee pad while patient is in the standing position.
Never try to adjust knee pad while the lift is moving.
Always make sure that the adjustment pins are engaged in the corresponding height
adjustment holes before using.
NOTE: For this procedure, refer to FIGURE 3.3.
1. Pick a height setting that will be
comfortable to the patient and provide
the necessary support.
Note: The upper adjustment
pins are typically used for
shorter individuals. The
lower adjustment pins are
typically used for taller
individuals.
NOTE: The knee pad should be positioned so
that the knee portion of the leg contacts the pad.
NOTE: The upper adjustment pins are
typically used for shorter individuals. The
lower adjustment pins are typically used for
taller individuals.
2. Using both hands, pull both
adjustment pins outward at the same
time and hold.
Adjustment Pin
Adjustment Pin
Knee Pad
3. Position the knee pad to the desired
height and release adjustment pins into
the corresponding alignment holes.
FIGURE 3.3 Adjusting the Knee Pad Height
4. Check to make sure that both pins are
engaged.
16
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFTING THE PATIENT
SECTION 4—LIFTING THE PATIENT
Introduction
ꢀ WARNING
The legs of the stand up lift MUST be in the maximum open position before lifting
the patient for optimum stability and safety. If it is necessary to close the legs to
maneuver the stand up lift under a bed, close the legs only as long as it takes to
position the stand up lift over the patient and lift the patient off the surface of the
bed. When the legs of the stand up lift are no longer under the bed, return the legs
to the maximum open position.
Invacare recommends that two assistants be used for all lifting preparation and
transferring to/from procedures; however, our equipment will permit proper operation
by one assistant. The use of one assistant is based on the evaluation of the health care
professional for each individual case.
Refer to the patient sling owner’s manual for complete lifting preparation information.
Refer to General Guidelines on page 8 in this manual before proceeding further and
observe all warnings indicated.
Lifting the Patient
ꢀ WARNING
DO NOT move the patient if the sling is not properly connected to the attachment
points of the stand up lift. Check that the sling is properly connected to the attachment
points prior to lifting a patient. If any attachments are not properly in place, correct the
problem. When the sling is elevated a few inches off the stationary surface and before
moving the patient, check again to make sure that all sling attachments are secure. If any
attachments are not properly in place, lower the patient back onto the stationary
surface and correct this problem - otherwise, injury or damage may occur.
Adjustments for safety and comfort should be made before moving the patient.
Patient’s arms should be outside of the straps.
DO NOT use slings and stand up lifts of different manufacturers. Invacare slings are
made specifically for use with Invacare stand up lifts. Injury or damage may occur.
NOTE: For this procedure, refer to FIGURE 4.1 on page 19.
1. Instruct patient to hold onto the handgrips on both sides of the stand up lift. Refer to
Detail “A ” .
2. Instruct the patient to lean back into the standing or transport sling.
Part No. 1148115
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFTING THE PATIENT
ꢀ WARNING
Before positioning the legs of the stand up lift around the patient, make sure the
patient’s feet are out of the way of the footplate, otherwise injury can occur.
Standing Slings - Before lifting the patient, make sure the bottom edge of the
standing sling is positioned on the lower back of the patient and the patient's arms
are outside the standing sling.
Transport Slings - Before lifting the patient, make sure the bottom edge of the
transport sling is at the base of the spine and the patient's arms are outside the
sling. DO NOT raise the patient to a full standing position.
3. Ensure the following:
• Patient’s knees are secure against the knee pad.
• Patientʹs feet are positioned on the footplate.
• The bottom edge of either the standing sling is positioned on the lower back or
the transport sling is at the base of the patientʹs spine.
• The patientʹs arms are outside of the standing or transport sling.
• The legs are in the maximum open position.
ꢀ WARNING
Before transferring, check that the wheelchair weight capacity can withstand the
patient's weight. Refer to Typical Product Parameters in the wheelchair owner’s
manual.
If transferring from a wheelchair, the wheelchair wheel locks MUST be in the locked
position before lowering the patient into the wheelchair. Otherwise, injury may
occur.
4. If transferring from a wheelchair, lock the wheel locks on the wheelchair. Refer to
Detail “B”.
5. Raise the patient above the surface (bed, wheelchair, or commode) high enough to
clear the surface. The patient’s weight will be fully supported by the lift. Refer to Detail
NOTE: The lower center of gravity provides stability making the patient feel more secure and the
lift easier to move.
NOTE: The lift arms will stay in position until lowered.
18
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFTING THE PATIENT
DETAIL “B” - WHEEL LOCK
DETAIL “A” - LIFT
Wheel Lock
Handgrips
Steering
Handle
DETAIL “C” - LIFTING THE PATIENT
Mast
Handle
Sling
Rear
Casters
Knee Pad
Footplate
FIGURE 4.1 Lifting the Patient
Moving the Patient
ꢀ WARNING
DO NOT move a person suspended in a sling any distance. The Invacare lift is NOT
a transport device. It is intended to transfer a seated individual from one resting
surface to another (such as a bed to a wheelchair). Otherwise, injury or damage
may occur.
The legs of the stand up lift MUST be in the maximum open position for optimum
stability and safety. If the patient is in a sling and it becomes necessary to move
through a narrow passage, close the legs of the stand up lift only as long as it takes
to move through the passage. When the stand up lift is through the passage, return
the legs to the maximum open position.
DO NOT roll caster base over objects such as carpet, raised carpet bindings, door
frames, or any uneven surfaces or obstacles that would create an imbalance of the
lift during transfer of a patient suspended in the lift sling. This could cause the lift to
tip over. Use the mast handle at all times to push or pull the lift.
NOTE: For this procedure, refer to Detail “C” of FIGURE 4.1.
1. Ensure the legs of the stand up lift are in the maximum open position. If not, open legs
to the maximum open position.
2. Move the stand up lift away from the surface using the steering handle.
3. Slowly move the patient to the desired surface.
Part No. 1148115
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFERRING THE PATIENT
SECTION 5—TRANSFERRING THE
PATIENT
ꢀ WARNING
DO NOT attempt any transfer of a patient without approval of the patient's
physician, nurse, or medical assistant.
DO NOT move the patient if the sling is not properly connected to the attachment
points of the stand up lift. Check that the sling is properly connected to the
attachment points prior to lifting a patient. If any attachments are not properly in
place, correct the problem. When the sling is elevated a few inches off the
stationary surface and before moving the patient, check again to make sure that all
sling attachments are secure. If any attachments are not properly in place, lower
the patient back onto the stationary surface and correct this problem - otherwise,
injury or damage may occur.
Adjustments for safety and comfort should be made before moving the patient. The
patient's arms should be outside the straps.
Before positioning the legs of the stand up lift around the patient, make sure the
patient’s feet are out of the way of the footplate, otherwise injury can occur.
DO NOT use slings and stand up lifts of different manufacturers. Invacare slings are
made specifically for use with Invacare stand up lifts. Otherwise, injury or damage
may occur.
The legs of the stand up lift MUST be in the maximum open position before lifting
the patient for optimum stability and safety. If the patient is in a sling and it
becomes necessary to move through a narrow passage, close the legs of the stand
up lift only as long as it takes to move through the passage. When the stand up lift is
through the passage, return the legs to the maximum open position. If it is
necessary to close the legs to maneuver the stand up lift under a bed, close the legs
only as long as it takes to position the stand up lift over the patient and lift the
patient off the surface of the bed. When the legs of the stand up lift are no longer
under the bed, return the legs to the maximum open position.
DO NOT roll caster base over objects such as carpet, raised carpet bindings, door
frames, or any uneven surfaces or obstacles that would create an imbalance of the
lift during transfer of a patient suspended in the lift sling. This could cause the lift to
tip over. Use the mast handle at all times to push or pull the lift.
Be sure to check the sling attachments each time the sling is removed and replaced
to ensure that it is properly attached before the patient is removed from a surface.
NOTE: Invacare recommends that two assistants be used for all lifting preparation and
transferring to/from procedures; however, our equipment will permit proper operation by one
assistant. The use of one assistant is based on the evaluation of the health care professional for each
individual case.
20
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFERRING THE PATIENT
Moving the Patient to a Commode
NOTE: For this procedure, refer to FIGURE 5.1.
1. Raise the patient high enough to clear
DETAIL “A” - POSITIONING PATIENT
the arms of the commode chair. Their
weight will be supported by the lift.
Refer to Detail “A ” .
2. Guide the patient onto the commode
chair.
3. Lower the patient onto the commode
chair.
4. Perform one of the following (refer to
Detail “B” or “C”):
• Standing Sling ‐ unhook the
standing sling from the attachment
points on the lift.
DETAIL “B” - UNHOOKING SLING
• Transport Sling ‐
i. Unhook the transport sling from
the bottom attachment points on
the lift.
ii. Lift up on the patient’s legs and
remove the thigh supports from
underneath the patient.
iii. If desired, unhook the transport
sling from the top attachment
points on the lift.
NOTE: The patient can remain in the upper
portion of the transport sling while using the
commode.
DETAIL “C” - UNHOOKING SLING AND
STRAPS
5. Instruct or assist the patient in lifting
their feet off the footplate.
6. Remove the sling from around the
patient.
7. Pull the lift away from the commode.
8. When complete, recheck the sling for
correct attachments.
9. To lift the patient from the commode,
Part No. 1148115
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFERRING THE PATIENT
DETAIL “A” - UNHOOKING SLING AND
STRAPS
Transferring to a
Wheelchair
NOTE: For this procedure, refer to
NOTE: Before transferring, check that the
wheelchair weight capacity can withstand the
patientʹs weight. Refer to Typical Product
Parameters in the wheelchair owner’s manual
1. Ensure the legs of the lift with the
patient in the sling are in the open
position.
DETAIL “B” - LOCKING THE WHEELCHAIR
2. Move the wheelchair into position.
Refer to Detail “A ” .
3. Engage the rear wheel locks of the
wheelchair to prevent movement of the
wheelchair. Refer to Detail “B”.
ꢀ WARNING
DO NOT place the patient in the
wheelchair if the locks are not engaged.
The wheelchair wheel locks MUST be in
a locked position before lowering the
patient into the wheelchair for
DETAIL “C” - LOWERING PATIENT
transport. Otherwise, injury may result.
4. Position the patient over the
wheelchair.
5. Lower the patient into the wheelchair.
Refer to Detail “C”.
6. Unhook the sling from all attachment
points on the lift. Refer to Detail “D”.
DETAIL “D” - UNHOOKING SLING
7. Instruct patient to lift their feet off the
footplate. Assist the patient if
necessary.
8. Remove the sling from around the
patient.
9. Pull the lift away from the wheelchair.
FIGURE 5.2 Transferring to a Wheelchair
22
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFERRING THE PATIENT
Transferring to a Bed
NOTE: For this procedure, refer to FIGURE 5.3.
NOTE: The lower center of gravity provides stability making the patient feel more secure and the
lift easier to move.
NOTE: The lift arms will stay in position until lowered.
1. Position the patient as far over the bed as possible.
NOTE: If patient is being transferred from a surface that is lower than the bed, raise the patient
above the surface of the bed. The patient should be elevated just high enough to clear the bed with
their weight fully supported by the lift.
2. Lower the patient onto the bed.
3. Unhook the sling from all attachment points on the lift.
4. Instruct the patient to lift their feet off of the footplate. Assist the patient if necessary.
5. Remove the standing or transport sling from around the patient.
6. Pull the lift away from the bed.
DETAIL “A” - LOWERING THE
PATIENT
DETAIL “B” - UNHOOKING
THE SLING
FIGURE 5.3 Transferring the Patient to a Bed
Part No. 1148115
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—USING LIFT AS A STANDING AID
SECTION 6— USING LIFT AS A
STANDING AID
NOTE: For this procedure, refer to FIGURE 6.1 on page 25.
NOTE: The Get‐U‐Up lift can be used as an aid to lift a person from a seated to a standing position.
A minimum of two caregivers is required for this procedure.
NOTE: Invacare recommends that two assistants be used for all lifting preparation and
transferring to/from procedures; however, our equipment will permit proper operation by one
assistant. The use of one assistant is based on the evaluation of the health care professional for each
individual case.
Standing Procedure
1. Ensure that the patient is capable of walking.
2. Fold the footplate toward the mast.
3. Use the adjustment pins to move the kneepad to a comfortable position.
4. Ensure that the patient is in a sitting position to begin the procedure.
A. If the patient is in bed and requires assistance to come to a sitting position, raise the
back of the bed.
B. Place the lift over the bed with the lift arms angled toward the patient.
C. Instruct the patient to grasp the lift arms.
D. As the lift arms are raised, the patient should move legs to the side of the bed until
a sitting position on the side of the bed is assumed.
NOTE: The caregivers should assist as needed.
E. Pull the lift away as needed to accommodate the patient’s feet and legs over the
side of the bed.
5. With one caregiver on each side of the patient, place a gait belt on the patient.
6. Ensure that the patient is wearing shoes with skid‐proof soles.
7. If the patient is on the bed, raise the bed (if possible) while ensuring that the patient’s
feet remain on the floor.
8. If a walker is to be used, place the walker in front of the patient.
9. Advance the lift toward the patient so that the patient can easily reach the lift arms.
10. Instruct the patient to grasp the lift arms.
11. Ensure that the patient’s feet are directly under them.
12. Begin raising the lift arms.
13. On a count of three, instruct the patient to pull and stand‐up while the caregivers
support with the gait belt.
24
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—USING LIFT AS A STANDING AID
ꢀ WARNING
DO NOT lift the patient.
14. Remove the lift to allow the patient to walk.
Lift Arm
Lift Arm
Mast
Post
Kneepad
Footplate
Base
Adjustment Pins
Note: The upper adjustment pins
are typically used for shorter
individuals. The lower adjustment
pins are typically used for taller
individuals.
Part No. 1148115
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SECTION 7— TROUBLESHOOTING
SYMPTOMS
FAULTS
SOLUTION
Stand up lift feels loose.
Mast/base joint loose.
Tie-rods are loose.
Tighten the bolt, washer and locknut that secure
the mast to the base.
Refer to Assembling the Base, Mast and Horn
Casters/brakes noisy or stiff.
Fluff or debris in bearings.
Needs lubrication.
Pull down slightly on the lift arms.
Noisy or dry sound from pivots.
Lift arms will not lower in upper-
most position.
Lift arms require a minimum
weight load to lower from the
uppermost position.
NOTE: If problems are not remedied by the suggested means, please contact your dealer or
Invacare.
26
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SECTION 8— MAINTENANCE
Maintenance Safety Inspection Checklist
For individual home use, a full inspection is required prior to each new user.
Regular cleaning will reveal loose or worn parts, enhance smooth operation and extend
the life expectancy of the lift.
Follow the maintenance procedures described in this manual to keep your stand up lift in
continuous service.
INSTITUTIONAL
INSPECT/ADJUST
MONTHLY
IN-HOME
INSPECT
PERIODICALLY
ITEM
INITIALLY
THE CASTER BASE
Inspect for missing hardware.
Base opens/closes with ease.
Inspect casters and axle bolts for tightness.
Inspect casters for smooth swivel and roll.
Inspect and clear casters of debris.
Inspect roll pin to ensure secure to base.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
THE MAST
Mast MUST be securely assembled to lift arms.
Inspect for bends or deflections.
Inspect pivot joints for wear.
X
X
X
X
X
X
X
X
X
THE LIFT ARMS AND LINKAGE
Check all hardware and attachment points.
Inspect for bends or deflections.
Inspect bolted joints of lift arms for wear.
Inspect to ensure that the lift arms are centered
between the base legs.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Ensure that the bolt is tightly secured.
Inspect pivot joints for wear.
SHIFTER HANDLE
Operates smoothly.
Locks adjustable base whenever engaged.
Check roll pin for wear
X
X
X
X
X
X
X
X
X
CLEANING
Whenever necessary.
X
X
X
SLINGS AND HARDWARE
CHECK ALL SLING ATTACHMENTS each time it is
used to ensure proper connection and patient safety.
Inspect sling material for wear.
Inspect straps for wear.
Check that all labels are present and legible. Replace
if necessary.
X
X
X
X
X
X
X
X
X
X
X
X
Part No. 1148115
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
The lift is designed to provide a maximum of safe, efficient and satisfactory service with
minimum care and maintenance.
All parts of the stand up lift are made of the best grades of steel, but metal to metal contact
will wear after considerable use.
There is no adjustment or maintenance of the casters, other than cleaning, lubrication and
checking axle and swivel bolts for tightness. Remove all debris, etc. from the caster and
swivel bearings. If any parts are worn, replace these parts immediately.
If you question the safety of any part of the lift, contact your dealer immediately and
advise them of the problem.
Hydraulic Pump
All parts of the hydraulic pump are precision machined then carefully assembled and
tested to ensure reliable service. The pump assembly is completely enclosed and sealed
with Neoprene rings to prevent leakage of hydraulic oil. A small amount of oil (about a
drop) will accumulate around the piston from time to time and should be removed with
a facial tissue.
ꢀ WARNING
The hydraulic pump is sealed at the factory and if service is required, the pump unit
MUST be returned to the factory for repair. DO NOT attempt to open the
hydraulic pump or obtain local service. This will void the warranty and might result
in damage and costly repair. Consult your dealer or contact Invacare for
information.
Lubricating the Lift
NOTE: For this procedure, refer to FIGURE 8.1.
The Invacare lift is designed for minimum maintenance. However, a six month check and
lubrication should ensure continued safety and reliability.
Keep lift and slings clean and in good
working order. Any defect should be noted
and reported to your dealer as soon as
possible.
The casters MUST swivel and roll
smoothly. A light grease (waterproof auto
lubricant) may be applied to the ball
bearing swivel of the casters once a year.
Apply more frequently if the casters are
exposed to extreme moist conditions.
Caster
(1 of 4)
Lubricate all pivot points. Wipe all excess
lubricant from lift surface.
28
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
The connection between the mast and the base should be cleaned and coated with
petroleum jelly prior to assembly.
Detecting Wear and Damage
It is important to inspect all stressed parts, such as slings, sling attachment knobs, and any
pivot for slings for signs of cracking, fraying, deformation or deterioration. Replace any
defective parts immediately and ensure that the lift is not used until repairs are made.
All sling metal parts should be inspected every three months and if wear is apparent,
replacement must be made.
Check that all labels are present and legible. Replace if necessary.
Cleaning the Sling and the Lift
The sling should be washed regularly in water temperature of 180°F (82°C) and a
biological solution. A soft cloth, dampened with water and a small amount of mild
detergent, is all that is needed to clean the lift. The lift can be cleaned with non‐abrasive
cleaners.
Replacing the Knee Pad
NOTE: For this procedure, refer to FIGURE 8.2.
1. Remove the four button screws and washers that secure existing knee pad to the lift.
2. Remove the existing knee pad from the lift.
3. Position the mounting holes in the new knee pad with the mounting holes in the lift.
4. Using the existing hardware, secure the new knee pad to the lift.
Button Screw and
Washer (1 of 4)
Knee Pad
Adjustment Pin
(1 of 2)
FIGURE 8.2 Replacing the Knee Pad
Part No. 1148115
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
NOTES
30
Part No. 1148115
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
NOTES
Part No. 1148115
31
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH
FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
Invacare warrants the products manufactured to be free from defects in materials and
workmanship for a period of three years on the lift and one year on the hydraulic pump from
the date of purchase. If within such warranty period any such product shall be proven to be
defective, such product shall be repaired or replaced, at Invacare’s option. This warranty does
not include any labor or shipping charges incurred in replacement part installation or repair of
any such product. Invacare’s sole obligation and your exclusive remedy under this warranty
shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare
product. In the event you do not receive satisfactory warranty service, please write directly to
Invacare at the address on the back cover, provide dealer’s name, address, date of purchase,
indicate nature of the defect.
Invacare Corporation will issue a serialized return authorization. The defective unit or parts
MUST be returned for warranty inspection using the serial number, when applicable as
identification within 30 days of return authorization date. Do not return products to our factory
without our prior consent. C.O.D. shipments will be refused; please prepay shipping charges.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY
TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR
DEFACED, PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER
OPERATION, MAINTENANCE OR STORAGE, PRODUCTS MODIFIED WITHOUT
INVACARE’S EXPRESS WRITTEN CONSENT (INCLUDING, BUT NOT LIMITED TO,
MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS;
PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT
WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT DAMAGED BY
CIRCUMSTANCES BEYOND INVACARE’S CONTROL, AND SUCH EVALUATION WILL
BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO
PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THE
INSTRUCTIONS IN THIS MANUAL.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER EXPRESS
WARRANTIES. IMPLIED WARRANTIES, IF ANY, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESSED WARRANTY
PROVIDED HEREIN AND THE REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY
SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT
PURSUANT TO THE TERMS CONTAINED HEREIN. INVACARE SHALL NOT BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
SOME STATES DO NOT ALLOW EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGE, OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE EXCLUSIONS AND LIMITATIONS MAY NOT APPLY TO YOU.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE OR PROVINCIAL
LAWS AND REQUIREMENTS.
Invacare Corporation
USA
Canada
All rights reserved. Trademarks are
One Invacare Way
Elyria, Ohio USA
44036-2125
570 Matheson Blvd E Unit 8 identified by the symbols ™ and ®. All
Mississauga Ontario
L4Z 4G4 Canada
800-668-5324
trademarks are owned by or licensed to
Invacare Corporation unless otherwise
noted.
800-333-6900
© 2007 Invacare Corporation
Part No. 1148115
Rev A - 7/07
Download from Www.Somanuals.com. All Manuals Search And Download.
|