T
TM
intelligent motion systems, inc.
TM
Excellence in Motion
IM481H
ULTRA MINIATURE HIGH PERFORMANCE
MICROSTEPPING DRIVE
OPERATING INSTRUCTIONS
370 N. MAIN ST., PO BOX 457, MARLBOROUGH, CT 06447
PH. (860) 295-6102, FAX (860) 295-6107
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION
PAGE
LIST OF TABLESAND FIGURES ..................................... 1
1
2
3
4
5
6
INTRODUCTION ............................................................... 2
PINASSIGNMENTAND DESCRIPTION ........................... 3
ELECTRICALSPECIFICATIONS ...................................... 4
THERMALSPECIFICATIONS ........................................... 4
MECHANICALSPECIFICATIONS
6.1 DIMENSIONALIMFORMATION ........................................ 5
6.2 MOUNTING INFORMATION .............................................. 6
OUTPUT CURRENT
7
8
7.1 DETERMINING OUTPUT CURRENT ................................. 7
7.2 SETTING OUTPUT CURRENT .......................................... 8
7.3 RESISTOR TABLE ........................................................... 9
MOTOR
8.1
8.2
9
MOTOR SELECTION.......................................................10
CONNECTING THE MOTOR ............................................10
POWER REQUIREMENTS
9.1 MOTOR POWER.............................................................12
9.2 +5 VDC INPUT ................................................................13
10LAYOUTAND INTERFACE GUIDELINES .................................14
11
MICROSTEP SELECTION ...............................................14
12FULLSTEP OUTPUT SIGNAL ...................................................16
13TIMING .....................................................................................16
14INPUTS ....................................................................................17
15AUTOMATIC CURRENTREDUCTION .......................................18
16FAULTPROTECTION ...............................................................19
18THERMAL REQUIREMENTS....................................................19
19OPTIONS/ACCESSORIES .......................................................20
AppendixA- Recommended Cable Configurations........................21
WARRANTY.................................................................................30
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
DIMENSIONALINFORMATION .............................. 4
MOUNTING INFORMATION .................................... 6
SETTING OUTPUT CURRENT ................................ 9
MOTOR CONNECTIONS .......................................12
POWER CONNECTIONS ......................................14
MICROSTEP RESOLUTION SELECTION..............16
INPUTS .................................................................18
FAULTIN/RESET - INTERFACE CIRCUIT ..............18
RESET TIMING .....................................................18
MULTIPLE DRIVES - ONE RESET........................18
AUTOMATIC CURRENTREDUCTION ...................19
LIST OF TABLES
Table 1
Table 2
Table 3
Table 4
Table 5
ELECTRICALSPECIFICATIONS ............................ 4
THERMALSPECIFICATIONS ................................. 4
RESISTOR TABLE ................................................10
POWER SUPPLY SPECIFICATIONS ....................13
MICROSTEP SELECTION.....................................15
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2
INTRODUCTION
The IM481H is a high performance, yet low cost microstepping driver that utilizes
advanced hybrid technology to greatly reduce size without sacrificing features. The
IM481H is exceptionally small, easy to interface and use, yet powerful enough to handle
the most demanding applications.
The IM481H has 14 built in microstep resolutions (both binary and decimal). The
resolution can be changed at any time without the need to reset the driver. This feature
allows the user to rapidly move long distances, yet precisely position the motor at the end
of travel without the expense of high performance controllers.
With the development of proprietary and patented circuits, ripple current has been
minimized to reduce motor heating common with other designs, allowing the use of low
inductance motors improving high speed performance and system efficiency.
The IM481H, because of its ultra small size and low cost, can be used to increase
accuracy and smoothness in systems using higher step angle motors. In many instances
mechanical gearing can be replaced with microstepping, reducing cost and eliminating
potential maintenance.
OPTIONAL INTERFACE BOARD The INT-481 is a plug on interface board which can be
used with the IM481H to facilitate testing or in situations where panel mounting is
preferred
The INT-481 contains extra circuitry which includes: Opto isolators for step clock,
direction, enable, and reset, along with extra fault detection circuits, +5vdc supply, input
capacitor, and fault and power LED’s. Wiring is done through a 15 pin screw terminal
header. A four position dip switch is supplied for microstep resolution selection.
FEATURES
•Very Low Cost
•Ultra Miniature 1.1” x 2.7” x 0.17”
•High Input Voltage (+12 to +48Vdc)
•High Output Current (1.5 Amps RMS, 2.3 Amps Peak)
•Advanced Hybrid Design
•Replaces Mechanical Gearing for Smoothness and Positioning
•Designed for High Performance, Low Inductance Stepping Motors
•20 KHz Chopping Rate
•Up to 10 MHz Step Clock Rate
•14 Selectable Microstepping Resolutions that can be changed On-The-Fly.
•Up to 51,200 Steps/Rev with a 1.8o Motor
•Automatically Switches between Slow and Fast Decay for Unmatched
Performance
•At Full Step Output
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3
PIN ASSIGNMENT AND DESCRIPTION
PIN #
1,2
PIN NAME
PHASE A
PIN FUNCTION
Phase A of the stepping motor is connected between pin 1 and pin 2. See section 8.
CURRENT
REDUCTION
ADJUST
Phase current reduction adjustment input. A resistor connected between this pin and pin
4 ( if used to set motor phase current ) will proportionately reduce current in both
windings approximately .5 seconds after the last positive edge of the step clock input.
See section 15.
3
4
5
6
CURRENT
REFERENCE
Phase current reference output. A resistor is connected between this 1 mA current
source output and the Ground pin ( pin 11 ) to generate the voltage used to set the peak
phase current in the motor. See section 7.
CURRENT
ADJUSTMENT
Phase current adjustment input. A voltage applied to this input sets the peak phase
current in the motor. See section 7.2.
FAULT INPUT
A low signal on this input will generate a latched fault condition. See section 16.
RESOLUTION
SELECT 0-3
Microstep resolution select inputs. Used to select the number of microsteps per step of
the motor. See section 11.
7-
10
SUPPLY
GROUND
Supply voltage ground ( return ). See section 9.
Supply voltage input. See section 9.
11
12
13
14
15
16
17
18
19
+V
RESET INPUT
+5V
When low, this input will reset the driver ( phase outputs will disable ). When released,
the driver will be at its initial state ( phase A off, phase B on ). See section 14.
+5Vdc supply input. This supply is used to power the internal logic. The +5Vdc supply
should be referenced to pin 11( supply ground ). See section 9.2.
STEP CLOCK
INPUT
A positive going edge on this input advances the motor one increment. The size of the
increment is dependent on the microstep select inputs See section 13.
DIRECTION
INPUT
This input is used to change the direction of the motor. Physical direction also depends
on the connection of the motor windings. See section 13.
ENABLE
INPUT
This input is used to enable/disable the output section of the driver. When high, the
outputs are enabled. However, this input does not inhibit the step clock. Therefore when
enabled the outputs will update by the number of clock pulses ( if any ) applied to the
driver while it had been disabled. See section 14.
ON-FULL-
STEP OUTPUT
This totem-pole output indicates when the driver is positioned at a full step. This output
can be used to count the number of full steps the motor has moved, regardless of the
number of microsteps in between. This output is active high. See section 12.
FAULT
OUTPUT
This totem-pole output indicates a short circuit has occurred or a low signal was
detected on the Fault input. This output is active high. See section 16
PHASE B
Phase B of the stepping motor is connected between pin 20 and pin 21. See section 8.
20-
21
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4
ELECTRICAL SPECIFICATIONS
Table 1
Test Parameters: T = 25oC,+V = 48v
A
TEST CONDITION
MIN TYP MAX UNITS
INPUT VOLTAGE ....................................................................................... 12.......45........ 48*.......... V
PHASE OUTPUT CURRENT......................................RMS .......................0.14 ...................1.5 .......... A
PHASE OUTPUT CURRENT..................................... PEAK..................................................2.3 .......... A
QUIESCENT CURRENT (+v, pin 12).......... INPUTS/OUTPUTS FLOATING .....................25......................mA
QUIESCENT CURRENT (+5vdc, pin 14).... INPUTS/OUTPUTS FLOATING ................................... 40........mA
ACTIVE POWER DISSIPATION .......................... I
= 1A RMS ............................................2.0 ......... W
OUT
LOW LEVEL INPUT VOLTAGE ............................. ALL INPUTS ..................... .......................0.8 .......... V
HIGH LEVEL INPUT VOLTAGE...................ALL INPUTS EXCEPT RESET......................2.0 ........................ V
HIGH LEVEL INPUT VOLTAGE................................ RESET ...................................2.3 ......................... V
INPUT PULL-UP RESISTANCE.................FAULT IN, RES SEL 0-3, ENABLE .......4.4 ......4.7 ........5.0 ........kΩ
INPUT PULL-UP RESISTANCE.....................STEP CLOCK, DIRECTION ...........2.1 ......2.2 ........2.3 ........kΩ
INPUT PULL-UP RESISTANCE................................ RESET .......................0.9 ......1.0 ........1.1 ........kΩ
LOW LEVEL OUTPUT CURRENT..................... FAULT, FULLSTEP................ 24..................................mA
HIGH LEVEL OUTPUT CURRENT.................... FAULT, FULLSTEP.................-2..................................mA
LOW LEVEL OUTPUT VOLTAGE ..........................I =24 mA...............................................0.4 .......... V
OL
HIGH LEVEL OUTPUT VOLTAGE..........................I = -2 mA ....................4.5 .................................... V
OH
*
INCLUDES BACK EMF OF MOTOR
SECTION 5
THERMAL SPECIFICATIONS
Table 2
STORAGE TEMPERATURE................................................ -40 TO +125 OC
OPERATING TEMPERATURE................................................0 TO +50 OC
‡REAR MOUNTING SURFACE (MAX) ....................................... +70 OC
‡ADDITIONAL COOLING MAY BE REQUIRED TO LIMIT REAR MOUNTING SURFACE
Care should be taken when choosing a heatsink to ensure that there is good thermal flow,
otherwise hot spots may occur in the IM481H which will reduce the effectivness of the
thermal protection.
W A R N I N G ! Rear mounting surface of driver contains
different voltages and must be keep isolated when attached
to a conductive surface !
An optional thermal pad ( Part # TI-481 ) and heat sink ( Part # H-481 ) is available
for the IM481H
NOTE:
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL SPECIFICATIONS
DIMENSIONAL INFORMATION
SECTION 6.1
Dimensions in Inches (mm)
2.700
(68.6)
2.450
(62.2)
2.225
(56.4)
IM481H
*Wt: 0.512 oz.
14.6 gms.
0.175
2 X Ø 0.150
(3.8)THRU
65°
TYP.
Heat Sink
1.100
This Side
(27.9)
0.175
(4.4)
0.563
(14.3)
PIN 1
0.058
(1.5)
0.225
(5.7)
0.016
(0.4) SQ.
0.100
(25.4)
3.000
(76.2)
INT-481
0.920
(23.37)
*Wt: 1.02 oz.
29.0 gms.
0.620
(15.75)
0.275
(6.99)
2.450
(62.23)
21 Pin Right Angle
Connector
HY481-CN021
21
1
SW1
ENOFF/ENON
MS0
MS1
MS2
MS3
1
3
Heat Sink
This Side
JP2
0.575
(14.6)
1.550
(39.37)
GRN
RED
LED1
2 X Ø 0.143
(3.6 ) Thru
2.872
(72.9)
1.875
H-481
*Wt: 2.40 oz.
68.1 gms.
(47.6)
0.178
(4.5)
0.312
(7.9)
0.498
(12.6)
1.312
(33.3)
2 X Ø 0.177
(4.5) Thru
1.100
(27.9)
0.550
(13.9)
0.211
(5.4)
2 X #6-32
Tapped Thru
2.450
(62.2)
* Does not include mounting hardware.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6.2
MOUNTING INFORMATION
IM481-H Driver and H-481 Heat Sink Direct Mount on PCB
D
NOTE: Components are
described in the table on the
following page.
F
*
4
1
3
C
A
B
G
0.096
(2.43)
PCB
Hole Pattern for Direct PCB Mounting
H-481 Heat Sink
Dimensions are in Inches (mm)
Ø 0.250 +0.003 / - 0.0
(6.35 +0.08 / - 0.0)
0.063
(1.6)
0.240
(6.1)
1.875
(47.63)
Pin #1
0.100 Typ
(2.54 Typ)
0.064 Pad, 0.031 Hole
(1.6 Pad, 0.78 Hole)
NOTE: The hardware items “A” through “H” are supplied with the
H-481 Heat Sink Kit. If the H-481 is not used, the mounting hardware is not supplied.
NOTE: The torque specification for the #6-32 INT-481 and IM481H mounting screw is
5.0 - 7.0 in-lbs. (See the hardware list on the following page.)
* The Isolating Thermal Pad (TI-481) item “4” is supplied with the INT-481 Interface
Board. If the INT-481 is not used, the Thermal Pad must be ordered seperately.
WARNING! The Heat Sink mounting surface must be a smooth, flat surface
with no burrs, protrusions, cuttings or other foreign objects.
WARNING! If you are planning to wash your PCB it must be done prior to
adding the IM481H Driver or damage will occur.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IM481-H Driver, INT-481 Interface Board, H-481 Heat Sink Panel Mount
3
F
E
H
*
4
1
2
0.915
(23.25) Ref.
C
B
A
IM481-H Driver, INT-481 Interface Board Panel Mount without Heat Sink
*
4
1
A
C
B
2
0.180
(4.57) Ref.
Product/Item #
Description
Qty.
1
1
2
3
4
A
B
C
D
E
IM481H Microstepping Driver
INT-481 Interface Board
H-481 Heat Sink
1
1
TI-481 Isolating Thermal Pad
#6-32x5/8" Pan Head Screw
#6 Split Lock Washer
1
2
2
#6 Flat Washer, 0.250" OD, 0.145" ID, 0.030" Thick
#8-32x13/8" Pan Head Screw
2
2
#8-32x2 Pan Head Screw
2
F
#8 Split Lock Washer
2
G
H
#8-32 Internally Threaded Broaching Nut
Spacer, 0.312" OD, 0.171" ID, 0.500" Long
2
2
* The Isolating Thermal Pad (TI-481) item “4” is supplied with the INT-481 Interface
Board. If the INT-481 is not used, the Thermal Pad must be ordered seperately.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OUTPUT CURRENT
SECTION 7.1
DETERMINING THE OUTPUT CURRENT
For any given motor, the OUTPUT CURRENT used for MICROSTEPPING is determined
differently from that of a HALF/FULL STEP driver.
In the IM481H, a sine/cosine output function is used in rotating the motor. Therefore, when
microstepping, the specified phase current of the motor is considered an RMS value.
The CURRENT ADJUSTMENT RESISTOR used to set the output current of the IM481H
sets the peak output of the sine/cosine waves not the RMS value. Therefore the specified
motor current (which is the RMS value) should be multiplied by 1.4 to determine the PEAK
value to which the IM481H will be set.
EXAMPLE:
If a motor has a specified PHASE CURRENT of 0.75 amps per phase, then:
0.75 amps X 1.4 = 1.05 amps peak
The Resistor Value = OUTPUT CURRENT X 1000 or in this example:
1.05 X 1000 = 1050 Ω.
Table 3 shows commercially available 1% resistors for a given current.
NOTE: Stepper motors can be configured as 4, 6, or 8 leads. Each configuration requires
different currents. Shown below are the different lead configurations and the procedures to
determine their output current.
4 Lead Motors: Multiply the specified phase current by 1.4 to determine the peak
output current.
6 Lead Motors: 1) When configuring a 6 lead motor in a half coil configuration ( i.e.
connected from one end of the coil to the center tap (high speed
configuration)) multiply the specified per phase (or unipolar) current
rating by 1.4 to determine the peak output current.
2) When configuring the motor so the full coil is used (i.e. connected
from end to end with the center tap floating (higher torque
configuration)) use the per phase (or unipolar) current rating as the
peak output current.
8 Lead Motors: SERIES CONNECTION: When configuring the motor windings in
series, use the per phase (or unipolar) current rating as the peak
output current, or multiply the bipolar current rating by 1.4 to
determine the peak output current.
PARALLEL CONNECTION: When configuring the motor windings in
parallel, multiply the per phase (or unipolar) current rating by 1.96 or
the bipolar current rating by 1.4 to determine the peak output current.
After determining the peak output current, use table 4 to choose the proper
current reference resistor value.
NOTE:
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7.2
SETTING OUTPUT CURRENT
The OUTPUT CURRENT on the IM481H is set by applying a voltage to pin 5 (current
adjustment). The output current is set as follows:
PEAK OUTPUT CURRENT (Amps) = Volts applied to pin 5
EXAMPLE:
1.4 volts applied to pin 5 will set the peak output current of the IM481H to 1.4
amps per phase.
To generate the reference voltage needed to set the peak output current of the driver, a
1mA current source is provided (pin 4, Current Reference ). By connecting a resistor ( 1/8
watt or higher ) between pin 4 and pin 11 ( Ground ) a reference voltage is generated. Pin
4 is then connected to pin 5 ( Current Adjustment) to set the peak per phase output
current of the driver ( See Figure 3 ).
The relationship between the output current and the resistor value is as follows:
PEAK OUTPUT CURRENT (Amps) x 1000 = Resistor Value (Ohms)
EXAMPLE: To set the peak output current of the IM481H to 1.4 Amps:
1.4 ÷ .001 = Resistor Value = 1400 .
Table 3 shows the standard 1% resistor values with respect to the peak output current.
NOTE: When using the Current Reference output to set the output current of the
IM481H, care should taken to keep the connections as short as possible
to help minimize the noise coupled into the driver.
1
2
3
4
5
6
7
8
9
1 0 1 11 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1
Current
Adjustment
Resistor
Figure 3
WARNING! A Current Adjustment Resistor is always necessary to keep the
Driver and/or Motor in safe operating range.
DO NOT operate the IM481H Driver without a Current Adjustment
Resistor!
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7.3
RESISTOR TABLE
Table 3
PEAK OUTPUT CURRENT
(AMPS)
REFERENCE
(VOLTS)
RESISTOR VALUE (1%)
(OHMS)
0.20................................0.20 .............................200
0.25................................0.25 .............................249
0.30................................0.30 .............................301
0.35................................0.35 .............................348
0.40................................0.40 .............................402
0.45................................0.45 .............................453
0.50................................0.50 .............................499
0.55................................0.55 .............................549
0.60................................0.60 .............................604
0.65................................0.65 .............................649
0.70................................0.70 .............................698
0.75................................0.75 .............................750
0.80................................0.80 .............................806
0.85................................0.85 .............................845
0.90................................0.90 .............................909
0.95................................0.95 .............................953
1.00................................1.00 ........................... 1000
1.05................................1.05 ........................... 1050
1.10................................1.10 ........................... 1100
1.15................................1.15 ........................... 1150
1.20................................1.20 ........................... 1210
1.25................................1.25 ........................... 1240
1.30................................1.30 ........................... 1300
1.35................................1.35 ........................... 1330
1.40................................1.40 ........................... 1400
1.45................................1.45 ........................... 1430
1.50................................1.50 ........................... 1500
1.55................................1.55 ........................... 1540
1.60................................1.60 ........................... 1580
1.65................................1.65 ........................... 1650
1.70................................1.70 ........................... 1690
1.75................................1.75 ........................... 1740
1.80................................1.80 ........................... 1780
1.85................................1.85 ........................... 1820
1.90................................1.90 ........................... 1870
1.95................................1.95 ........................... 1960
2.00................................2.00 ........................... 2000
2.05................................2.05 ........................... 2050
2.10................................2.10 ........................... 2100
W A R N I N G ! Although stepping motors will run hot when
configured correctly, damage may occur to a motor if a higher than
specified current is used. Most specified motor currents are maximum
values. Care should be taken when exceeding these ratings.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTOR
SECTION 8.1
MOTOR SELECTION
The IM481H is a Bipolar driver which works equally well with both Bipolar and Unipolar
motors, ( i.e. 8 and 4 lead motors and 6 lead center tapped motors (see section 8.2,
Connecting the Motor)).
To maintain a given set motor current, the IM481H chops the voltage using a constant
chopping frequency and a varying duty cycle. Duty cycles that exceed 50% can cause
unstable chopping. This characteristic is directly related to the motor’s winding
inductance. To avoid this situation, it is necessary to choose a motor with a low winding
inductance. The lower the winding inductance, the higher the step rate possible.
The maximum per phase motor inductance for the IM481H is calculated as follows:
Max. per Phase Inductance (mH) = 2 x Supply Voltage ÷ 10
NOTE: In calculating the maximum phase inductance, when using an unregulated
power supply, the minimum supply output voltage should be used.
Since the IM481H is a constant current source, it is not necessary to use a motor that is
rated at the same voltage as the supply voltage. What is important is that the IM481H is
set to the motor’s rated current.
The higher the voltage used the faster the current can flow through the motor coils. This in
turn means a higher step rate. Care should be taken not to exceed the maximum voltage
of the driver.
Therefore in choosing a motor for a system design, the best performance for a specified
torque is a motor with the lowest possible winding inductance used in conjunction with the
highest possible driver voltage.
SECTION 8.2
CONNECTING THE MOTOR
Phase A of the Stepping Motor is connected between pins 1 and 2. Phase B of the
Stepping Motor is connected between pins 20 and 21. The following drawings in figure 4
illustrates the connection of 4,6, and 8 Lead Stepping Motors to the IM481H Driver.
NOTE: To reduce the transmission of EMI from the motor cables, a twisted pair
sheilded cable is recommended if the driver to motor cabling is in excess of
one foot. Motor leads should not exceed 100 feet. Refer to Section 10,
Recommended Wiring, for further information.
NOTE: The physical direction of the motor with respect to the direction input will
depend on the connection of the motor windings. To reverse the direction of
the motor with respect to the direction input, switch the wires on either
phase A or phase B outputs.
WARNING! Do not connect or disconnect the AC power leads
or the motor leads with power applied!
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTOR CONNECTIONS
1
2
1
2
PHASE A
PHASE B
PHASE A
PHASE B
20
21
20
21
8 LEAD MOTOR
8 LEAD MOTOR
SERIES CONNECTION
PARALLEL CONNECTION
1
2
1
2
NC
NC
PHASE A
PHASE B
PHASE A
PHASE B
NC
20
21
20
21
NC
6 LEAD MOTOR
6 LEAD MOTOR
HIGHER SPEED CONFIGURATION
( HALF COIL )
HIGHER TORQUE CONFIGURATION
( FULL COIL )
NC: NO CONNECTION
NC: NO CONNECTION
1
2
PHASE A
PHASE B
20
21
4 LEAD MOTOR
Figure 4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER REQUIREMENTS
MOTOR POWER
SECTION 9.1
Pins 11 (ground), and 12 (+V) are used to connect the motor DC power to the IM481H.
Two local capacitors are needed, connected between pins 11 and 12 and located as
close to the pins as possible, to insure stable operation.
The first capacitor is a low impedance, aluminum electrolytic. The continuous operating
voltage of the capacitor should exceed the maximum supply voltage as well as any
additional voltage caused by the motors back EMF. The value of the capacitor should be
approximately 150 microfarads for every 1 amp of peak per phase output current.
EXAMPLE: For a peak output current of 1.4 amps, and a supply voltage of 45 volts, a
220uf 50v capacitor is recommended.
Along with the aluminum electrolytic, a 0.1 microfarad ceramic capacitor must be used to
filter out high frequency noise. It should be located between the IM481H’s power input
pins and the aluminum electrolytic capacitor. The continuous operating voltage of the
capacitor should exceed the maximum supply voltage as well as any additional voltage
caused by the motors back EMF.
POWER SUPPLY SPECIFICATIONS
Table 4
Recommended Type:..............Unregulated DC.
Ripple Voltage............................. ±10% max.
Output Voltage......................... +12 to +45Vdc
*Output Current.................. 0.75 Amps (TYPICAL)
NOTE: RECOMMENDED POWER SUPPLY IMS: PART # ISP200-4
NOTE:
With the exception of IMS Power Supplies, Switching Power Supplies and
regulated linears with overcurrent protection are not recommended because of
their inability to handle surge currents. If multiple drivers are to be run off of one
power supply each drive should have separate power and ground wires that
connect directly to the output capacitor of the power supply.
*THE OUTPUT CURRENT NEEDED IS DEPENDENT ON THE SUPPLY VOLTAGE,
MOTOR SELECTION, AND LOAD.
W A R N I N G : When using an unregulated power supply, care
should be taken that the output voltage does not exceed the
maximum driver input voltage because of variations in line
voltage. It is recommended that a input line filter be used on the
power supply to limit voltage spikes to the driver!!
W A R N I N G : Do not connect or disconnect motor leads with
power applied !! Do not connect or disconnect power supply
with power applied !!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9.2
+5 VDC INPUT
The IM481H requires an external regulated +5Vdc power supply. The supply is connected
between pins 11 (ground), and 14 (+5vdc). A 22 microfarad 10v tantilum capacitor must
be placed as close to the IM481H as possible between the +5vdc input pin (14) and
ground.
The +5vdc supply ground and the motor supply ground should not be connected together
at the power supplies. The common ground connection between the motor power supply
and the +5vdc supply should be made at the ground pin of the additional electrolytic
capacitor used for the motor supply (see section 9.1)
Figure 5 shows the proper connection of the external +5vdc supply to the IM481H.
Care should be taken when using this supply not to couple noise from
external circuits into the IM481H which could cause erratic operation or
damage.
NOTE:
+5VDC
SUPPLY
MOTOR
SUPPLY
Figure 5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10
LAYOUT AND INTERFACE GUIDELINES
Logic level signals should not run parallel to motor phase signals. The motor phase signals
will introduce noise into the logic level signals and can make the system unreliable. Motor
phase signals should run as pairs and should be separated from other signals by ground
traces where possible.
When leaving the board, motor cables should not be run parallel with other wires and
phases should be wired using twisted pairs. If motor cabling in excess of 1 foot is required,
the use of a shielded twisted pair cable is recommended to reduce the transmission of
EMI. The shield must be tied to AC ground at the driver end only. The motor end must be
left floating.
If more then one driver is to be connected to the same power supply, separate power and
ground connections from each driver to the power supply should be used.
The power supply cables need to be a twisted pair if power is connected from a source
external to the board. If multiple drivers are used with an external power source, and it is
not possible to run separate power and ground connections to each driver, a low
impedance electrolytic capacitor equivalent to 2 times the total capacitance of all the driver
capacitors ( see section 9 Power requirements ) and of equal voltage must be placed at
the power input to the board.
MOTOR CABLES
Dual Twisted Pair Shielded (Separate Shields)
< 5 feet ............................................................ Belden Part # 9402 or equivalent 20 Gauge
> 5 feet ............................................................ Belden Part # 9368 or equivalent 18 Gauge
POWER SUPPLY CABLES
Twisted Pair (Jacketed)
< 4 Amps DC current....................................... Belden Part# 9740 or equivalent 18 Gauge
> 4 Amps DC current....................................... Belden Part# 8471 or equivalent 16 Gauge
SECTION 11
MICROSTEP SELECTION
The number of microsteps per step is selected by pins 7 thru 10. Table 5 shows the
standard resolution values along with the associated input settings ( See section 14 -
Inputs ).
The microstep resolution can be changed at any time. There is no need to reset or cycle
power. On-the-fly “gear shifting” facilitates high speed slewing combined with high
resolution positioning at either end of the move.
When the number of microsteps per step are changed such that the IM481H does not fall
on a full step (i.e. zero crossing of the sine/cosine waveforms) the IM481H will re-adjust
itself at the next pulse that would overshoot the full step position. This feature allows the
IM481H to re-adjust the motor to position no matter what resolution is chosen or when it is
changed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MICROSTEP SELECTION
Table 5
RESOLUTION
(Microsteps/Step)
STEPS/REV
RESOLUTION
SELECT 0
PIN 7
RESOLUTION RESOLUTION
RESOLUTION
SELECT 3
PIN 10
(1.8o Step Motors)
SELECT 1
PIN 8
SELECT 2
PIN 9
BINARY
2
4
400
LOW
HIGH
LOW
HIGH
LOW
HIGH
LOW
HIGH
LOW
LOW
HIGH
HIGH
LOW
LOW
HIGH
HIGH
LOW
LOW
LOW
LOW
HIGH
HIGH
HIGH
HIGH
LOW
LOW
LOW
LOW
LOW
LOW
LOW
LOW
800
8
1,600
3,200
6,400
12,800
25,600
51,200
16
32
64
128
256
DECIMAL
5
1,000
2,000
LOW
HIGH
LOW
HIGH
LOW
HIGH
LOW
LOW
HIGH
HIGH
LOW
LOW
LOW
LOW
LOW
LOW
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
10
25
5,000
50
10,000
25,000
50,000
125
250
ILLEGAL SETTINGS: MAY CAUSE ERRATIC OPERATION
LOW
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
Figure 6
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12
FULLSTEP OUTPUT SIGNAL
The FULLSTEP output signal from the IM481H is an active high output at pin 18. This
output is TRUE for the duration of the full step. A full step occurs when either Phase A or
Phase B cross through zero (i.e. full current in one winding and zero current in the other
winding). This fullstep position is a common position no matter what resolution is
selected.
The fullstep output can be used to count the number of mechanical full steps the motor
has traveled without having to count the number of microsteps in between. A controller
that utilizes this output can greatly reduce its position tracking overhead and thus
substantially increasing its throughput.
SECTION 13
TIMING
The Direction and Microstep Resolution Select inputs are syncronized with the positive
going edge of the Step Clock input. When the Step Clock input goes high, the Direction
and Microstep Select inputs are latched and further changes to these inputs are ignored
until the next rising edge of the Step Clock input.
After these signals are latched, the IM481H looks to see if any changes have occured to
the Direction and the Microstep Select inputs. If a change has occurred, the IM481H will
execute the change before taking the next step. Only AFTER the change has been
executed will the step be taken. If no change has occured the IM481H will simply take
the next step. (This feature works as an automatic debounce for the Direction and
Microstep Select inputs.)
The minimum pulse width for the Step Clock input is 75nS. The typical execution time for
a Direction or Microstep Select change is 100nS. The typical execution time for a Step
input is 100nS.
The Reset and Enable inputs are asynchronous to any input and can be changed at any
time.
The Reset requires a minimum pulse width of 10µS (See Section 14 for more
information).
The Fullstep output typically occurs 75nS after the positive edge of the Step Clock
(excluding changes to the Direction or the Microstep Select inputs).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 14
INPUTS
The inputs to the IM481H are internally pulled up
to the +5VDC internal supply. Figure 7 shows the
inputs and their associated pull up resistor
values. See Section 4, Electrical Specifications,
for resistor tolerence.
1
2
3
+5V
4
5
6
7
8
Fault In
Resolution Select 0
Resolution Select 1
Resolution Select 2
Resolution Select 3
4.7k Ω
4.7k Ω
4.7k Ω
4.7k Ω
4.7k Ω
9
10
11
12
13
14
Reset
+5 VDC
1k
Ω
An open collector output is recommended
when interfacing with the IM481H.
Step Clock 15
2.2k Ω
2.2k Ω
4.7k Ω
Direction
Enable
16
17
18
19
20
21
On power up, or if the Reset Input is Closed,
the internal reset circuit will hold the input
low for 100 to 300 milliseconds. The
“holding” time does not begin until the Reset
Input is Opened. (See Figure 9.)
Figure 7
W A R N I N G! When interfacing the FAULT IN or RESET input, an
open collector, tri-state output, or a blocking diode is REQUIRED or
damage may occur to internal circuits. (See Figure 8.)
1N914 OR EQUIVALENT
FAULT IN/RESET
INPUT
Circuit
OR
INTERFACE
CIRCUIT
FAULT IN /RESET
INPUT
Figure 8
RESET BUTTON
Circuit
Open
Circuit Open
Closes at T=0
+5 V
300
Internal Reset Hold Time
Starts When Circuit Opens
0
100
200
Milliseconds
Figure 9
UNIT #1
RESET
13
RESET
BUTTON
When controlling multiple drives with a single
Reset you must install blocking diodes at the
input (Pin 13) of each drive. Because of the
slight differences in Reset timing, this will
prevent the drives from latching the Reset
Input in the LOW state. (See Figure 10.)
INPUT
1N914 OR
EQUIVALENT
UNIT #2
13
13
RESET
INPUT
1N914 OR
EQUIVALENT
UNIT #3
RESET
INPUT
1N914 OR
EQUIVALENT
Figure 10
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 15
AUTOMATIC CURRENT REDUCTION
Built into the IM481H is the ability to automatically reduce the current in the motor
windings after the completion of a move. The reduction occurs approximately .5 seconds
after the last positive going edge of the Step Clock input. The IM481H will then revert
back to the original current setting at the next positive going edge of the Step Clock input.
To utilize this feature, the current reference output must be used to adjust the output
current of the IM481H and a resistor must be connected between pins 3 & 4 (see Figure
6). The value of the resistor will determine the amount of current reduction.
The amount of current per phase in the current reduction mode is related to the value of
the current reference resistor and the current reduction resistor. When the current
reduction circuit is activated, the current reduction resistor is paralleled with the current
adjustment resistor. The parallel combination of the current reference and current
reduction resistors determine the reduced current level. The relationship between the
output current and the resistor's values is as follows:
.001 x *R(Current Adjust) x R(Current Reduction)
Output Current Reduced (Amps)=
R(Current Adjust) + R(Current Reduction)
OR
Output Current Reduced x R(Current Adjust)
R(Current Reduction) =
.001 x R(Current Adjust) - Output Current Reduced
NOTE: Resistor values are in ohms.
CURRENT
REDUCTION
RESISTOR
CURRENT
ADJUSTMENT
RESISTOR
Figure 11
When connecting the current reduction resistor between pins 4 and 5, the
connections should be made as short as possible to help minimize noise
coupled into the driver.
NOTE:
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 16
FAULT PROTECTION
The IM481H is internally protected against over temperature, and over current.
The over temperature set point is between 60 and 70 °C. Care should be taken when
choosing and installing a heat sink so that there is a good thermal conduction, otherwise
hot spots may occur in the IM481H which will reduce the operating thermal range.
The over current protection consists of PHASE to PHASE, and +V to PHASE.
If an output driver in the IM481H detects an over temperature condition it will shut down
but will not activate the fault output. Once the temperature drops to a safe operating
temperature, the IM481H will resume operation.
If an over current fault is detected by the IM481H, the outputs will be disabled and cannot
be re-enabled without resetting the driver or by cycling power. At the same time the active
high FAULT output (pin 19) is enabled.
The FAULT IN input (pin 6) can be used to force a fault condition. When pulled low the
signal is latched and the outputs will be disabled. The fault condition can only be cleared
by cycling power or resetting the driver.
SECTION 17
THERMAL REQUIREMENTS
The IM481H may require heat sinking to maintain a safe operating temperature. Care
should be taken when mounting the IM481H to a heat sink with an electrically conductive
surface that an isolating thermal pad is used.
W A R N I N G ! Rear mounting surface of driver contains
different voltages and must be kept isolated when attached
to a conductive surface !
An optional thermal pad ( Part # TI-481 ) and heat sink ( Part # H-481 ) is available
for the IM481H
NOTE:
The watts dissipated by the IM481H can be calculated as follows:
Watts Dissipated = ( 0.6 x ( Peak per Phase Output Current )2 )
EXAMPLE: Peak per Phase Output Current = 1.4 amps
Watts Dissipated = 1.18
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 18
OPTIONS/ACCESSORIES
DESCRIPTION
PART NUMBER
Thermal Pad
TI - 481
Interface Board
INT-481
H-481
Heat Sink ( Includes mounting hardware )
21 Pin Right Angle Connector
Small End Screw Driver
HY481-CN021
SD1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P E N D I X A
R e c o m m e n d e d C a b le C o n f ig u r a t io n s :
D C S u p p ly t o IM S D r iv e r
Cable length, wire gauge and power conditioning devices play a major role
in the performance of your IMS Driver and Motor.
NOTE: The length of the DC power supply cable to the IMS Driver should
not exceed 50 feet.
Example A demonstrates the recommended cable configuration for DC
power supply cabling under 50 feet long. If cabling of 50 feet or longer is
required, the additional length may be gained by adding an AC power
supply cable (see Examples B & C).
Correct AWG wire size is determined by the current requirement plus cable
length. Please see the IMS Driver Supply Cable AWG Table in this
Appendix.
Exa m p le
A
–
Ca b lin g Un d e r 5 0 Fe e t , DC P o we r
To IMS Driver
-
π Type RFI Filter
≥ Required Current
Ferrite
Beads
Shielded Twisted Pair
(Wire Size from
IMS Driver Supply Cable AWG Table)
Cable Length
less than 50 Feet
DC Voltage from
Power Supply
Shield to Earth Ground
on Supply End Only
-
500 µf
Per Amp
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Exa m p le
B
–
Ca b lin g 5 0 Fe e t o r Gr e a t e r ,
AC P o we r t o Fu ll W a ve Br id g e
NOTE:
To Cable A
Connect the cable illustrated
in Example A to the output of
the Full Wave Bridge
-
Full Wave Bridge
Cable Length
as required
Shielded Twisted Pair
(Wire Size from
IMS Driver Supply Cable AWG Table)
π Type RFI Filter
≥ Required Current
Shield to Earth Ground
on Supply End Only
Transformer :
0 to 28 VAC RMS
for 48 VDC Systems
20 to 48 VAC RMS
for 75 VDC Systems
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Exa m p le
C
–
Ca b lin g 5 0 Fe e t o r Gr e a t e r ,
AC P o we r t o P o we r S u p p ly
DC Volts Out
NOTE:
To Cable A
Connect the cable illustrated
in Example A to the output of
the Power Supply
-
Power Supply
Cable Length
as required
Shielded Twisted Pair
(Wire Size from
IMS Driver Supply Cable AWG Table)
π Type RFI Filter
≥ Required Current
Shield to Earth Ground
on Supply End Only
120 or 240 VAC
Dependent on
Power Supply
24
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: These recommendations will provide optimal
protection against EMI and RFI. The actual cable type,
wire gauge, shield type and filtering devices used are dependent
on the customer’s application and system.
IMS Driver Supply Cable AWG Table
1 Ampere (Peak)
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 20 20 18 18 16
2 Amperes (Peak)
Length (Feet)
10 25 50* 75* 100*
Minimum AWG 20 18 16 14 14
3 Amperes (Peak)
Length (Feet)
10 25 50* 75* 100*
Minimum AWG 18 16 14 12 12
4 Amperes (Peak)
Length (Feet)
10 25 50* 75* 100*
Minimum AWG 18 16 14 12 12
* Use the alternative methods innustrated in
Examples B and C when the cable length is
≥
50
feet. Also, use the same current rating when the
alternate AC power is used.
Driver Supply Cable Wire Size
NOTE: Always use Shielded/Twisted Pairs for the IMS Driver
DC Supply Cable, the AC Supply Cable and the IMS Driver to
Motor Cable.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
R e c o m m e n d e d C a b le C o n f ig u r a t io n s :
IM S D r iv e r t o M o t o r
Cable length, wire gauge and power conditioning devices play a major role
in the performance of your IMS Driver and Motor.
NOTE: The length of the DC power supply cable between the IMS Driver
and the Motor should not exceed 50 feet.
Example A demonstrates the recommended cable configuration for the IMS
Driver to Motor cabling under 50 Feet long. If cabling of 50 feet or longer is
required, the additional length can be gained with the cable configuration in
Example B.
Correct AWG wire size is determined by the current requirement plus cable
length. Please see the IMS Driver to Motor Cable AWG Table in this Appendix.
Exa m p le
A
-
Ca b lin g Un d e r 5 0 Fe e t ,
IM S Dr ive r t o M o t o r
Phase A
Phase A
Phase B
Phase B
Ferrite
Beads
Cable Length
less than 50 Feet
Two Shielded/Twisted Pairs
(Wire Size from
IMS Driver to Motor Cable AWG Table)
Phase A
Phase A
Phase B
Phase B
Shield to Earth Ground
on Supply End Only
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Exa m p le
B
- Ca b lin g 5 0 Fe e t o r Gr e a t e r ,
IM S Dr ive r t o M o t o r
Phase A
Phase A
Phase B
Phase B
Ferrite
Beads
Cable Length
50 Feet or greater
Two Shielded/Twisted Pairs
(Wire Size from
IMS Driver to Motor Cable AWG Table)
Phase A
Phase A
Shield to Earth Ground
on Supply End Only
Common Mode
Line Filters (2x)
Phase B
Phase B
*L ≈ 0.5 MH
* 0.5 MH is a typical starting point for the
Common Mode Line Filters. By increasing
or decreasing the value of L you can set the
drain current to a minimum to meet your requirements.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
IMS Driver to Motor Cable AWG Table
1 Ampere (Peak)
5 Amperes (Peak)
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 20 20 18 18 16
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 16 16 14 12 12
2 Amperes (Peak)
6 Amperess (Peak)
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 20 18 16 14 14
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 14 14 14 12 12
3 Amperes (Peak)
7 Amperess (Peak)
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 18 16 14 12 12
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 12 12 12 12 12
4 Amperes (Peak)
* Use the alternate method illustrated in Example B
Length (Feet) 10 25 50* 75* 100*
Minimum AWG 18 16 14 12 12
when cable length is
≥
50 feet.
Driver to Motor Supply Cable Wire Size
NOTE: These recommendations will provide optimal
protection against EMI and RFI. The actual cable type,
wire gauge, shield type and filtering devices used are dependent on
the customer’s application and system.
NOTE: Always use Shielded/Twisted Pairs for the IMS Driver
DC Supply Cable, the AC Supply Cable and the IMS Driver to
Motor Cable.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
TWENTY-FOUR (24) MONTH LIMITED WARRANTY
Intelligent Motion Systems, Inc. (“IMS”), warrants only to the purchaser of the Product
from IMS (the “Customer”) that the product purchased from IMS (the “Product”) will be free
from defects in materials and workmanship under the normal use and service for which the
Product was designed for a period of 24 months from the date of purchase of the Product by
the Customer. Customer’s exclusive remedy under this Limited Warranty shall be the repair
or replacement, at Company’s sole option, of the Product, or any part of the Product,
determined by IMS to be defective. In order to exercise its warranty rights, Customer must
notify Company in accordance with the instructions described under the heading “Obtaining
Warranty Service.”
This Limited Warranty does not extend to any Product damaged by reason of alteration,
accident, abuse, neglect or misuse or improper or inadequate handling; improper or
inadequate wiring utilized or installed in connection with the Product; installation, operation
or use of the Product not made in strict accordance with the specifications and written
instructions provided by IMS; use of the Product for any purpose other than those for which
it was designed; ordinary wear and tear; disasters or Acts of God; unauthorized attachments,
alterations or modifications to the Product; the misuse or failure of any item or equipment
connected to the Product not supplied by IMS; improper maintenance or repair of the Product;
or any other reason or event not caused by IMS.
IMS HEREBY DISCLAIMS ALL OTHER WARRANTIES, WHETHER WRITTEN OR
ORAL, EXPRESS OR IMPLIED BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE. CUSTOMER’S SOLE REMEDY FOR ANY DEFECTIVE
PRODUCT WILL BE AS STATED ABOVE, AND IN NO EVENT WILL THE IMS BE LIABLE
FOR INCIDENTAL, CONSEQUENTIAL, SPECIAL OR INDIRECT DAMAGES IN
CONNECTION WITH THE PRODUCT.
This Limited Warranty shall be void if the Customer fails to comply with all of the terms set
forth in this Limited Warranty. This Limited Warranty is the sole warranty offered by IMS with
respect to the Product. IMS does not assume any other liability in connection with the sale of
the Product. No representative of IMS is authorized to extend this Limited Warranty or to
change it in any manner whatsoever. No warranty applies to any party other than the original
Customer.
IMS and its directors, officers, employees, subsidiaries and affiliates shall not be liable for
any damages arising from any loss of equipment, loss or distortion of data, loss of time, loss
or destruction of software or other property, loss of production or profits, overhead costs,
claims of third parties, labor or materials, penalties or liquidated damages or punitive damages,
whatsoever, whether based upon breach of warranty, breach of contract, negligence, strict
liability or any other legal theory, or other losses or expenses incurred by the Customer or
any third party.
OBTAINING WARRANTY SERVICE
Warranty service may obtained by a distributor, if the Product was purchased from IMS by
a distributor, or by the Customer directly from IMS, if the Product was purchased directly
from IMS. Prior to returning the Product for service, a Returned Material Authorization (RMA)
which an RMA Authorization Form with RMA number will then be faxed to you. Any questions,
contact IMS Customer Service (860) 295-6102.
Include a copy of the RMA Authorization Form, contact name and address, and any
additional notes regarding the Product failure with shipment. Return Product in its original
packaging, or packaged so it is protected against electrostatic discharge or physical damage
in transit. The RMA number MUST appear on the box or packing slip. Send Product to:
Intelligent Motion Systems, Inc., 370 N. Main Street, Marlborough, CT 06447.
Customer shall prepay shipping changes for Products returned to IMS for warranty service
and IMS shall pay for return of Products to Customer by ground transportation. However,
Customer shall pay all shipping charges, duties and taxes for Products returned to IMS from
outside the United States.
Download from Www.Somanuals.com. All Manuals Search And Download.
P.O. Box 457, 370 North Main Street
Marlborough, CT 06447 U.S.A.
Phone: 860/295-6102
Fax: 860/295-6107
Email: [email protected]
IMS EUROPE GmbH
Hahnstrasse 10, VS-Schwenningen
Germany D-78054
Phone: +49/7720/94138-0
Fax: +49/7720/94138-2
European Sales Management
4 Quai Des Etroits
TECHNICAL SUPPORT
Eastern U.S.
Phone: 860/295-6102
Fax: 860/295-6107
E-mail: [email protected]
Western U.S.
Phone: 760/966-3162
Fax: 760/966-3165
69005 Lyon, France
Phone: +33/4 7256 5113
Fax: +33/4 7838 1537
E-mail: [email protected]
German Sales/Technical Support
Phone: +49/35205/4587-8
Fax: +49/35205/4587-9
IMS MOTORS DIVISION
105 Copperwood Way, Suite H
Oceanside, CA 92054
Email: [email protected]
Phone: 760/966-3162
Fax: 760/966-3165
E-mail: [email protected]
IM481H Operating Instructions
Revision 051205
Download from Www.Somanuals.com. All Manuals Search And Download.
|