|
Copyright©2008
All Right Reserved - Printed in China
W476 / W576 Notebook User's Manual
Original Issue: 2008/08
This manual guides you in setting up and using your new Notebook PC. Information in the manual has been carefully checked for
accuracy and is subject to change without notice.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, photocopy, recording, or otherwise, without prior written consent.
Trademarks
Product names used herein are for identification purposes only and may be the trademarks of their respective companies.
Microsoft®, MS-DOS, Windows®, and Windows® Sound System are trademarks of Microsoft Corporation.
Intel®, Centrino™, Centrino Duo™, Pentium® M, Banias, Calexico are registered trademarks of Intel Corporation.
Sound Blaster, Sound Blaster Pro are trademarks of Creative Technology.
All other brands or product names mentioned in this manual are trademarks or registered trademarks of their respective companies.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
• When traveling, do not check your notebook as baggage. You can
put your notebook through an X-ray security machine, but never
put your notebook through a metal detector. If you have your note-
book checked by hand, be sure to have a charged battery ready in
case you are asked to turn on your notebook.
pulled out evenly in order not to bend its connecting pins. Also, be-
fore you connect the power cord, make sure that both connectors
are correctly oriented and aligned.
• Before you clean your notebook, turn it off first, unplug it from its
power source, and remove the battery.
• When traveling with the hard drive removed from your notebook,
wrap the drive in an insulated material, such as cloth or paper. If
you have the drive checked by hand, you may be asked to install
the drive into your notebook. Your can have the hard drive checked
through an X-ray machine, but never put the drive through a metal
detector.
• Handle interior components with care. When removing a compo-
nent, please hold it by the edge and not on the connecting pins
(such as the memory module).
When using your telephone equipments, safety instructions
should always be followed in order to prevent fire, electrical
shock or injuries, these instructions include:
• When traveling, do not place your notebook in the overhead stor-
age compartment where it could shift around. Do not drop your
notebook or subject it to other mechanical shocks.
• Do not use this product near water, for example, near a bath-
tub, washing basins, kitchen/laundry sinks, wet basements or
swimming pools.
• Protect your notebook, battery, and hard drive from environmental
hazards such as dirt, dust, food, liquids, extreme temperature, and
direct exposure to sunlight.
• Avoid using cordless phones during an electrical storm as light-
ening may cause electrical shocks.
II
• When you move your notebook in environments where there is a
substantial difference of temperature or humidity level, condensa-
tion may form on or within your notebook. To avoid damaging your
notebook, please allow sufficient time for the moisture to evaporate
before continue using.
• Do not use the telephone to report a gas leak within the leak-
age area.
WARNING: Void of Warranty
* If the battery is not properly handled, there may be a risk of
explosion; make sure you are using the same or compatible
battery.
NOTICE: When taking your notebook from a colder to a warmer environ-
ment or vice versa, allow your notebook enough time to adapt to the
new environment before turning on power.
* Please discard used batteries according to the instructions given
by the manufacturer.
* Please be aware that use of cracked, severely scratched or poor
quality discs may damage the optical drive and corrupt data in
the disc. Such discs may break while drive operates in high-
speed, in this case, your product warranty may be voided.
•When unplugging the power cord, please make sure that you pull
on its connector or on its strain relief loop, and not on the power
cord itself. As you pull out the connector, please ensure that it is
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communications Commission (FCC)
PART 68 Warning
Regulatory Notices
Federal Communications Commission Notice
This equipment complies with Part 68 of the FCC Rules. On the
bottom of the computer is a label that contains, among other in-
formation, the FCC Registration Number and Ringer Equivalence
Number (REN) for this equipment. You must, upon request, provide
this information to your telephone company.
This equipment has been tested and found to comply with the limits
for a Class B digital service, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
FCC Part 68 Registration Number: 6CTTAI - 25876 - FB - E
REN: 0.8B
Any changes or modifications made to this equipment may void the
user’s authority to operate this equipment. This equipment gener-
ates, uses, and can radiate radio frequency energy. If not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
The REN is useful to determine the quantity of devices you may
connect to your telephone and still have those devices ring when
your number is called. In most, but not all areas, the sum of the
REN’s of all devices should not exceed five (5.0). To be certain of
the number of devices you may connect to your line, as determined
by the REN, you should call your local telephone company to de-
termine the maximum REN for your calling area.
III
● Reorient or relocate the receiving antenna.
If your MODEM causes harm to the telephone network, the local
Telephone Company may discontinue your service temporarily. If
possible, they will notify you in advance. However, if advanced no-
tice isn’t practical, you will be notified as soon as possible. You will
be informed of your right to file a complaint with the FCC.
● Increase the separation between the equipment and receiv-
er.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician
for help.
Your telephone company may make changes in its facilities, equip-
ment, operations, or procedures that could affect the proper func-
tioning for your equipment. I they do, you will be notified in advance
to give you an opportunity to maintain an uninterrupted telephone
service.
● All external cables connecting to this basic unit must be
shielded.
For cables connecting to PCMCIA cards, see the option
manual or installation instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
CE Notice (European Union)
This symbol
indicates this W476 / W576 notebook computer
The symbol above must be attached to the product indicating
compliance with the BSMI standard.
complies with the EMC Directive and the European Union’s Low
Voltage Directive. This symbol also indicates that W451U meets the
following technical standards:
•
•
•
EN 55022 — “Limitations and Methods of Measurement for the
Radio Interferences of Information Technology Equipment.”
EN 55024 — “Information technology equipment - Immunity char-
acteristics - Limits and methods of measurement.”
CCC Notice (China Only)
• For W476 only
On Class A systems, the following warning will appear near the
regulation label:
EN 61000-3-2 — “Electromagnetic compatibility (EMC) - Chapter
3: Limits - Section 2: Limits on the harmonic current emissions
(Equipment input current up to and including 16 A per phase).”
EN 61000-3-3 — “Electromagnetic compatibility (EMC) - Chapter
3: Limits - Section 3: Limits on the voltage fluctuations and flicker
in low-voltage power supply systems for equipment with rate cur-
rent up to and including 16 A.”
Warning: This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case users may be
required to take adequate measures.
•
•
IV
Caution: Suggest to operate under 35˚C
EN 60950 — “Safety of Information Technology Equipment.”
NOTE: EN 55022 emissions requirements provide for two
classificaatios
• Class A governs commercial use
• Class B is governs residential use
BSMI Notice (Taiwan Only)
Most notebook computers are classified by the Bureau of Stan-
dards, Meteorology and Inspection (BSMI) as Class B information
technology equipment (ITE).
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Congratulations on your purchase of a Notebook computer! Your
new notebook features the most innovative features in portable
computing technology. It combines state-of-the-art ergonomics with
sophisticated architecture, providing you with a personal computer
that is compact, powerful, and easy to use. Designed for a wide
range of general, business, and personal productivity applications,
this notebook is an ideal choice for use in the office, at home, and
on the road.
This Manual contains all the information you need to set up and
use your notebook computer, It describes all of its features in a
thorough yet easy-to-read manner.
V
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
2.7 PCI Express card/Newcard...................................................18
2.8 Connecting to the HDMI Port ...............................................19
2.9 MS/ MS PRO/MS DUO/MMC/SD Cards...............................19
2.10 Using your Bluetooth (optional) and Wireless devices. ........20
Content
Safety instructions ......................................................................... I
Regulatory Notices........................................................................ III
Preface..........................................................................................V
Chapter 3 Troubleshooting
3.1 Frequently Asked Questions.................................................22
Appendix A W476 Specifications..................................................24
Appendix B W576 Specifications..................................................26
Appendix C Service Centers ........................................................28
Chapter 1 Operating Basics
1.1 Using the Battery Pack .........................................................02
1.2 Connecting the AC Adapter..................................................03
1.3 Turning Your Notebook On and Off......................................03
1.4 Installing W476 / W576 Device Drivers ................................04
1.5 Using the Power button ........................................................04
1.6 Keyboad Functions...............................................................05
1.7 Using the Touchpad..............................................................08
1.8 Storage .................................................................................09
1.9 Inroducing the Camera .........................................................10
1.10 Graphics Display...................................................................10
1.11 Protecting Your W476 / W576 Notebook Computer.............12
VI
Chapter 2 Connecting Peripherals
2.1 Using the USB Port...............................................................15
2.2 Connecting to an External Monitor via the D-sub Port .........15
2.3 Using the Port Replicator Connector ...................................16
2.4 Using the LAN Port...............................................................17
2.5 Using the Modem Port..........................................................17
2.6 Using the e-SATA Port ........................................................18
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
Chapter 1 Operating Basics
This chapter will show you how to operate your W476 / W576
notebook computer, including connecting the AC adaptor, turning
the computer on/off, using touch-pad, keyboard, hot keys, battery,
and so on. If you are new to computers and to the operating
system, this chapter will guide you through some of the new
exciting features.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
►Replacing the Battery◄
1.1 Using the Battery Pack
The battery will gradually weaken over time. We recommend that
you replace your battery when you notice a significant decrease of
battery capacity.
W476 / W576 notebook computer is designed to operate with one
of the following power sources:
• AC power
To change the battery pack, follow the steps below:
1. Turn off the computer.
(using the AC adapter connected to an electrical outlet)
• Lithium-Ion (Li-Ion) battery pack
2. Close the lid and flip the computer over.
3. Slide the side battery latch (1) to the left. Continue to hold it
until the battery is removed.
You should use the AC adapter whenever possible; use the battery
pack only when AC power is unavailable. The rechargeable Li-
Ion battery pack allows you to operate your notebook computer
without an external power source. When you use the AC adapter
to connect your notebook to a power outlet, the internal battery will
begin to recharge. While the battery is charging, the Battery Charge
icon on the indicator panel will be on. Once the battery is fully
charged, the Battery Charge icon will turn off. Quick charging time
is 2.5 hours for the Lithium-Ion (Li-Ion) battery when the computer
is turned off, while the normal battery charging time is 3.5 hours.
4. Make sure the replacement battery is properly oriented before
inserting it into the battery compartment.
Note: The battery can not be charged to 100% when remaining
battery is no less than 95%. It is based on the supplier’s advice,
and to extend charging frequency and battery life.
►Maintenance of the AC Adapter◄
ꢂ
• Do not connect the adapter to any other device.
•
Do not step on the power cord or place heavy objects on top of it. Ca-
refully route the power cord and keep cables away from all traffic.
• Operating a fax modem, video, or audio equipment can increase
the use of your computer’s power.
• When unplugging the power cord, do not pull on the cord itself but
on the plug instead.
• Decreasing monitor brightness can also save power.
• When the battery is not fully charged, allow your battery to be
charged completely before using it (i.e., before disconnecting AC
power). Calibrating the battery before use is also highly recom-
mended.
• If you are using an extension cord, make sure that the devices
plugged onto the cord do not exceed its total capacity. Furthermo-
re, the devices plugged into the electrical outlet shall not exceed
the fuse’s total ampere rating.
• Please verify power voltage before connecting the electrical cord
to the power outlet. If you are uncertain of its power specification,
please consult with your local vendors or power company for more
details.
• Li-Ion Battery is vulnerable, do not charge it with other power adap-
ter, otherwise fire or explosion may occur.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
1.2 Connecting the AC Adapter
1.3 Turning Your Notebook On and Off
The AC adapter converts AC power to DC power and reduces the
voltage supplied to the computer. It can automatically adjust to any
voltage from 100 to 240 volts and outputs power at 19V, 4.74A for
W476V / W576V (19V, 3.42A for W476M / W576M), allowing you to
use your notebook computer in almost any region.
►Turning on the power◄
Open the notebook lid, press and hold the power button for one or
two seconds. The power indicator will glow blue once the computer
is powered on.
►Turning off the power◄
CAUTION: Use only the AC adapter and the power cord we
recommend. Using the wrong adapter may damage your computer.
We assume no responsibilities for damages arising from misuse of
AC adapters.
If you are not going to use your notebook computer for a while,
it is best to turn off its power. Before turning off power, close all
programs first and shut down the operating system.
After turning off your notebook computer, make it a habit to leave
the LCD panel open for a while after it has been used for an
extended period of time. This allows the interior of your notebook
computer to cool off. Closing the panel will force the heat up
against the LCD screen, and doing so after a while may damage
the screen. More importantly, never close the LCD panel for a long
period of time when the computer is on or when the power saving
function is disabled.
To properly connect the adapter, follow the steps as below:
ꢁ
2
3
1
►Suspend mode◄
You can adjust default power management settings in the Power
Option/Advanced dialog box. The Power Options dialog box
provides several operating functions after your computer has been
idle for a while.
1. Connect the power cord to the AC adapter.
2. Connect the AC adapter to the DC power port of your computer.
3. Connect the AC adapter power cord to an AC outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Installing W476 / W576 Device Drivers
1.5 Using the Power button
If your W476 / W576 Notebook Computer already has an operating
system installed, it is best to install all necessary device drivers in
order for he hardware to properly function.
The power button located on the top side allow you to power on.
Before installing drivers, check with your vendors to see if they
have already installed all the drivers with the operating system, if
not, please follow the steps below:
1. You can find the Utility Driver CD like the one shown below:
ꢄ
2. Put the CD into the CD R-W or DVD-RW (optional) Drive. An
Auto Run installation screen will appear.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
1.6 Keyboad Functions
W476 / W576 notebook computer is equipped with a standard
typewriter-layout keyboard and has extra features.
<Shift> key. Press this key in combination with letters
to produce uppercase letters in typing. Use this key
in combination with those two-character keys (found
on the second row of the keyboard) to produce the
upper marked keys. Also used in most programs
in combination with other keys to execute a certain
command.
Basic Keypad
Keypad
Function Desription
<Enter> key. Execute a command. Within many text
editing programs, the <Enter> key inserts a hard carriage
return, just like what an ordinary typewriter does.
<Esc> key. Press this key to cancel or escape from a
command or function.
<Tab> key. Press this key to move the cursor to the
next tab on the right. This key works much the same
way as on an ordinary typewriter.
<Ins> key. Known as the Insert key. Press this key to
change from insert to type over mode.
<Ctrl> key. Known as the Control key. Used in most
programs in combination with other keys to execute a
command.
ꢃ
<Fn>+<PrtSc> key. Known as the Print Screen key.
Press this key to map the whole screen to share memory
for your specific usage.
+
<Alt> key. Known as the Alternate key. Used in most
programs in combination with other keys to execute a
command.
<Del> key. Known as the Delete key. Press this key to
delete the character to the right of the cursor, or delete
marked texts or items.
<Pause> key. Press this key to temporarily halt execution
of a command. Pressing any other keys to resume
execution of a command.
Download from Www.Somanuals.com. All Manuals Search And Download.
<Num Lk> key. Activates the embedded 15-key numeric
keypad.
Special Function Keys
►Embedded Numeric Keypad◄
<Fn>+<Scr Lk> key. Used in most programs to scroll the
screen without having to move the cursor. The keys are
in color-coded blue.
+
<Cap Lock> key. Used in most programs to always
activate uppercase letters.
Up arrow key. Moves the cursor up one line at a time.
Down arrow key. Moves the cursor down one line at a
time.
The embedded numeric keypad functions like the one on a desktop
keyboard. It is indicated by small characters located on the upper
left-hand corner of the keycaps.
Left arrow key. Moves the cursor to the left one space at
a time.
Desired Access
Num Lock On
Num Lock Off
ꢆ
Right arrow key. Moves the cursor to the right one space
at a time.
Number keys on
Type numbers in a
normal manner
embedded keypad
<Home> key. Moves the cursor to the beginning of a
screen or line.
Note: If an external keyboard or keypad is connected to your
notebook computer, the Numlock automatically shifts from an
internal keyboard to the external keyboard or keypad.
<PgUp> key. Moves the cursor up one screen at a time.
<PgDn> key. Moves the cursor down one screen at a
time.
<End> key. Moves the cursor to the end of a screen or a
line.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
►Windows Keys◄
►Basic keypad◄
you can input letters, numbers, punctuation marks, and special
symbols with it.
►Fn Keys◄
Key
+[F1]
+E
Description
By pressing the Fn key with other keys, it can simulate all keyboard
functions of a regular desktop keyboard.
Opens help and support
Explores my computer
Finds document
ꢅ
Suspend switch
[Fn]+[F1]
Activate or deactivate wireless functions
[Fn]+[F2]
Switch between LCD or CRT monitor
[Fn]+[F3]
+F
Increase screen brightness
[Fn]+[F4]
Decrease screen brightness
[Fn]+[F5]
[Fn]+[F6]
+M
Minimizes all
Audio mute
Decrease audio volume
[Fn]+[F7]
[Fn]+[F8]
+ Shift + M Undoes minimize all
Increase audio volume
+ R
Displays run dialog box
Play or pause media player
Stop media player
[Fn]+[F9]
[Fn]+[F10]
[Fn]+[F11]
[Fn]+[F12]
[Fn]+[Esc]
+ Tab
Activates next taskbar button
Media player skip backward
Media player skip forward
Enable or disable Bluetooth function
Download from Www.Somanuals.com. All Manuals Search And Download.
►Double Clicking◄
1.7 Using the Touchpad
Move the pointer over to the item with your finger on the pad, and
click twice on the left button to select menu items, or simply tap
twice on the touchpad.
The Touchpad is a pressure-sensitive pointing device that provides
all of the features of a two-button mouse; its primary function is to
move the cursor around the screen.
►To drag and drop◄
Touchpad
Move the pointer over to the item with your finger on the pad, click
once on the left button beneath the Touchpad and select the item
you want, once the item is selected, you can then drag the item by
gliding your finger on the Touchpad (clicking twice on the Touchpad
buttons equals to the speed of a double-click on a regular mouse).
Touchpad
buttons
►The Scroll buttons◄
If you are scrolling through the document, you may do so by gliding
your finger on the Touchpad while holding the scroll button.
ꢈ
You may adjust your Touchpad settings by going into Start/Control
Panel /Mouse/Buttons. You can change the Touchpad’s operating
orientations through these settings, for example changing from
right-handed to left-handed operations. You may also adjust cursor
speed as well as response time of mouse clicks.
Since the Touchpad is a pressure-sensitive device, therefore
proper care should be attended to in order to prevent damage.
Please also note the following precautions:
• Make sure the touchpad does not come into contact with dirt,
liquid or grease.
• Do not touch the touchpad if your fingers are dirty.
• Do not place heavy objects on the touchpad or on the touchpad
buttons.
►Clicking◄
You can move the pointer over to the item with your finger on the
pad, and click once on the left button below to select it, or simply
tap once on the touchpad.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
4. Slide the tray back until it clicks shut.
1.8 Storage
►Hard Disk◄
2
W476 / W576 notebook computer is equipped with a built-in large
capacity 2.5 inch IDE hard disk drive where you store or install
your computer operating system as well as software programs. The
internal hard disk is normally assigned as Drive C after formatting.
1
If you wish to replace your hard disk, contact your local
vendor for information about your notebook computer’s
hardware setup.
Warning: When the computer is reading from the optical drive, the
indicator light for ODD will flash on. Do not attempt to remove the
disc while the indicator light is still active.
You can increase the system’s storage capacity by replacing
the standard hard disk drive with a drive of a greater capacity.
Always turn off your notebook computer before removing the
hard drive. Failure to do so will damage the computer and the
hard disk. Avoid jarring or moving your computer while the
hard disk is still being accessed.
Warning: Do not insert any foreign objects into the disc tray. Do not
force the tray to open or close. When the drive is not in use, keep
the tray closed in order to prevent dust or dirt from entering the drive.
If you experience difficulty when removing a disc, stick a paper clip (or
use a pin or a thin metal rod) into the emergency eject hole, the CD
disc tray should eject immediately. This procedure can also be used
to remove a CD from the drive when the notebook is powered off.
Please refer to figure below.
ꢇ
►Optical Disc Drive (ODD)◄
W476 / W576 notebook computer is equipped with one of the DVD
Super Multi
The optical drive is normally used for installing operating system
and software programs. To insert and remove a disc from the drive:
1. Press the button on the front of the drive to eject the disc tray
and gently pull out the tray.
2. Place the disc on the tray with label side up.
3. Place the disc on the spindle and press it down gently until the
disc clicks into place.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.9 Inroducing the camera
1.10
Graphics Display
Your computer has a high-performance graphics display system, which
can easily handle the demands of today’s multimedia computing.
Your W476 / W576 notebook computer comes with a built-in cam-
era.With this camera, you can conduct videoconferences with your
friends or colleagues whenever and wherever as if they are right in
front of you. It also works as a digital camera (with a resolution up to
2.0 Megapixel) that you can use to take snapshots instantly.
►Screen Controls◄
Brightness
Function keys can increase or decrease the brightness of the monitor.
• <Fn> + <F4> decreases the LCD panel brightness.
• <Fn> + <F5> increases the LCD panel brightness.
►W476 / W576 camera
Resolution
1. Click My Computer/Control Panel/Appearance and Themes/ Display.
Click on the Settings tab. The dialog box will display your monitor’s
current resolution.
2. Under “Screen resolution,” use the slide bar to adjust monitor’
s resolution. Normally, you should use the resolution your LCD
monitor was designed for.
ꢀ0
Note: Using a lower resolution than the screen was designed for will
reduce the displaying area. Using the computer in DOS mode produces
the same effect, because it uses a 640 by 480 resolution by default.
►Dual Displays◄
Under Windows operating system, you may use an external monitor
and your notebook’s LCD screen simultaneously. You may also choose
to only use the external monitor with the LCD disabled or vice versa.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
1. Open Control Panel.
2. Double-click on Display. The Display Properties window will
open.
3. Click on the Settings tab.
4. Click on the Advanced button.
■ W476V / W576V
Click on GeForce 9300 (W476V) or 9600 (W576V) tab.
Choose nView Display Settings to adjust.
Single Display (for both W476V / W576V and W476M / W576M)
In Single Display mode, you can choose which device to apply as
the Primary display. The video display hot keys are available. You
can select different video outputs by pressing Fn+F3 repeatedly.
ꢀꢀ
Clone (for W476V / W576V)
Extended Desktop (for W476M / W576M)
In Clone/Extended Desktop mode, the video display hot keys
are available. You can select different video outputs by pressing
Fn+F3 repeatedly. If the external monitor is connected, the display
on LCD and external monitor is the same.
Dualview (for W476V / W576V)
Dual Display Clone (for W476M / W576M)
In Dualview/Dual Display Clone mode, choose the monitor for
extended display. Dualview/Dual Display Clone mode is controlled
by the driver. You can adjust the type of video output in the Menu.
Fn+F3 has no switch function under this mode.
■ W476M / W576M
Choose Intel Graphics Media Accelerator Driver for mobile.
Click Graphics Properties to adjust.
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip: In order to ensure problem-free video display, when you
use an external monitor, change the output mode in the Display
properties dialog box first. After changing the output mode, you
can then use the video display hot keys.
1.11
Protecting Your W476 / W576 Notebook
Computer
W476 / W576 Notebook Computer provides both hardware and
software security locks to protect your computer.
Note: Light or dark pixels may appear on the LCD screen as a
result of LCD’s manufacturing limitations, however, this will not
effect your LCD screen’s normal functions.
Using a security lock:
A security lock notch can be found on the right side of the com-
puter. This notch allows you to connect a Kensington-compatible
security lock to it.
►W476 security lock
ꢀꢂ
►W576 security lock
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
• Supervisor Password
Using a system protecing:
A Supervisor Password is required before you set User Password.
After selecting Change Supervisor Password, enter a new pass-
word then re-enter it to confirm. The password you enter should
contain up to 6 alphanumeric characters. If you make a mistake
while entering your password, you can always press Esc to start
over.
You can only enter the BIOS setup utility only when the computer
is turned on, in another word, between the time it’s turned on and
before the Windows splash screen appears. If your computer is
already turned on, reboot your computer and press the F2 key to
enter the setup utility.
►Security menu◄
• User Password
You can enter into the setup utility to change or remove user pass-
words; however, you can not change or remove the Supervisor
Password, nor can you access the diskette.
• HDD Password
To input, change, or disable hard drive password. When shown as
[Locked], the hard drive password currently can not be changed
or disabled. To change or disable the function, turn off the system
and enter Setup right after turning it back on.
ꢀꢁ
* Please remember the password when you decide to use HDD
Password. Your notebook service center may not be able to re-
store the HDD once the password is missing.
Help
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Connecting Peripherals
This chapter will show you step-by-step how to connect your
peripherals to the W476 / W576 notebook computer.
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
1. Turn off your W476 / W576 notebook and make sure the
monitor power switch is turned off.
2. Connect the connector cable of the monitor to the D-sub port
on the left side of your notebook. Secure the cable connection
with the screws provided.
2.1 Using the USB Port
The USB port allows multiple peripherals to run simultaneously on
a single computer. These peripherals may include: floppy drives,
mouse, digital cameras, scanners, printers, optical disk drive,
keyboards, and games devices...etc. The USB Port can also act as
a hub or as an external workstation.
3. Connect the monitor power cable and plug it into a properly
grounded wall outlet.
4. Turn on the monitor.
►W476 USB Port
5. Turn on your W476 / W576 notebook. Both the LCD panel and
the monitor screen will show the display. Your notebook is set
at default to run at simultaneous display mode.
6. If you only want to show the display on the external monitor
(CRT/LCD) and shut off the LCD display, you can use the <Fn>
+ <F3> hot-key to switch display type between LCD and CRT.
Keep pressing the hot-key until you get the display to external
CRT/LCD only.
►W476 D-sub Port
ꢀꢃ
►W576 USB Port
►W576 D-sub Port
2.2 Connecting to an External Monitor via the D-sub Port
The notebook comes with a D-sub port for you to connect to an
external monitor. To connect an external monitor, please follow the
steps below:
Download from Www.Somanuals.com. All Manuals Search And Download.
1. DC Power Port
2.3 Using the Port Replicator Connector(
)
W576 Only
Lets you connect the AC power adapter in supplying continuous
power to your Port Replicator.
Port Replicator Connector allows you to connect an external port
replicator devices (optional). This external device is an easy one-
step connectivity solution whether at home or the office.
2
Serial Port
The serial port, or COM port, allows you to connect serial
devices, such as printers or scanners.
3. External Monitor Port
The external monitor port allows you to connect an external
monitor.
4. Parallel Port
The parallel port, or LPT port, allows you to connect parallel
devices, such as a printer to your notebook.
5. USB V2.0 Port
The two USB ports allow you to connect USB devices such
as external game pads, pointing devices, key boards and/or
speakers.
ꢀꢆ
6. RJ45 10/100/1000Mbps Ethernet LAN Port
Internal LAN port connects your notebook to other computers/
networks through a local area network (LAN)
7. Stereo Line-out Port
The optional stereo line-out port allows you to connect a set of
speakers or a headphone to your notebook.
8. Power Switch
To power up or off the port replicator.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
2.4 Using the LAN Port
2.5 Using the Modem Port
1. Connect one end of the cable into the network wall outlet or the
The built-in fax/data modem allows you to connect a phone line to
a phone jack.
HUB.
2. Connect the other end of the cable into the computer’s LAN
port.
►
W476
Modem Port
►
LAN Port
W476
ꢀꢅ
►
LAN Port
►
W576
Modem Port
W576
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Using the e-SATA Port
2.7 PCI Express card/Newcard
The PCI Express card (or Newcard) slot can be used as an
interface between your computer and a variety of communication
devices, such as network adapters, fax/modems or external
storage devices.
With the built-in e-SATA port, you can connect your e-SATA-
compatible peripherals for data backup. The Windows operating
system will automatically recognize the device and install
appropriate driver(s) for it. Yet it is still recommended to install
the drivers that came with your peripherals. For more information,
please refer to your hardware manuals.
►Inserting a Card◄
1. Insert the card with label side up, make sure that the metal
connector is inserted into the card slot.
►
W476
e-SATA Port
2. Insert the card into the slot. You will feel some resistance as the
card reaches to the end.
3. Your PCI Express cards require drivers, or programs that
allow the operating system to use the device. Your Windows
operating system should already contain the driver for your
device, if not, you will be prompted to install the driver.
ꢀꢈ
►W476 Newcard slot
►
W576
e-SATA Port
►W576 Newcard slot
►Removing a Card◄
Press the eject button on the card slot to release the eject
button, then press the eject button again to release the card.
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
2.8 Connecting to the HDMI Port
2.9 MS/ MS PRO/MS DUO/MMC/SD Cards
Your W476 / W576 notebook computer comes with an HDMI port
which allows you to connect your computer to an external television
set. This is possible by using an HDMI cable:
Multimedia card slot is located on the right side of your W476 /
W576 notebook computer, it accepts MS/ MS PRO/MS DUO/
MMC/SD cards.
►W476 HDMI port
►W476 Multimedia card slot
ꢀꢇ
►W576 HDMI port
►
W576 Multimedia card slot
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 Using your Bluetooth (optional) and Wireless
devices.
Your W476 / W576 computer supports both Bluetooth and Wi-Fi
compatible devices. You can press Fn+Esc to enable or disable
Bluetooth function only and press Fn+F2 to turn on/off wireless
function only.
****For how to connect your Bluetooth and wireless device to your
computer, please refer to the manual from your hardware
manufacturers.****
ꢂ0
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
Chapter 3 Troubleshooting
In this chapter, we will list some frequently encountered technical
problems and tell you how to resolve them.
ꢂꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
the volume bar.
3.1 Frequently Asked Questions
My computer switches to hibernation mode much too quickly
What kind of external microphone can I use with my notebook
computer?
and I have to constantly hit a key or move the mouse to bring
back the screen. What can I do?
You will need to use a self-amplifying microphone.
This is part of Windows Power Management. Access Power
Management by clicking on Start / Control Panel / Performance
and Maintenance / Power Options, and change the time next to
the “Turn off monitor” option to the time you want. You have the
choice of either adjusting time for the power supply or for the
battery.
There are echoes coming from my speakers. What can I do?
Double click on the Speaker icon on the task bar. Then, under
Microphone Balance, check the Mute box.
Because of a software problem, I was unable to shut the
computer down from Windows, I pressed the power button to
I’ve heard that cleaning and rearranging files on the hard drive
will improve program’s launch speed. How do I do this?
power off the computer, but it didn’t work. How can I force a
power off?
ꢂꢂ
Good disk maintenances can improve program launch
speed. This normally includes deleting unnecessary files, and
defragmenting hard disk so that files can be more efficiently
grouped. Windows contains maintenance utilities for these
tasks; run Disk Cleanup to remove unnecessary files, and Disk
Defragmenter to defragment fragmented file blocks. For more
information about these utilities, please refer to your Windows
documentation.
Make sure you press the power button for at least 4 seconds.
Normally, this will force the computer to shut off.
Why can’t I charge the battery of my notebook computer after it
is out of use for some time?
After your notebook computer has not been used for a long
time (for example: more than one month), the battery will enter
into low voltage protection mode. Under this circumstance,
restoring to normal voltage will require the battery to be slowly
charged for several hours. Once the battery has been fully
charged, your computer will resume to normal operation.
The dial tone volume of the internal fax/modem is too low. How
can I increase its volume?
Go to Start/Control Panel/Sounds, Speech, and Audio Devices,
under Device volume, adjust your speaker volume by controlling
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
Caution
My computer says: “CMOS Battery Low”, what should I do?
Unplugging or ejecting a device that supports safe removal
without first using the Safe Removal application to warn the
system can cause data to be lost or your system to become
unstable. For example, if a device is unplugged during a data
transfer, data loss is likely. If you use Safe Removal, however,
you can warn the system before you unplug or eject a device,
preventing possible loss of data.
If your computer is without power (i.e. unplug the computer
power source from the power outlet and remove the battery
pack from it) for over 45 days, you would lose the information
stored in CMOS.
Please follow the steps below to reconfigure your CMOS
settings:
1. Press F2 to enter into the BIOS setup utility.
2. Select “Load Optional Defaults?”. When you see the
following prompt, choose <OK> and then press <Enter>.
3. Select “Save Changes and Exit”, select <OK> and press
<Enter> to restart your computer.
Note
For removable storage devices that can safely be removed
while the system is on, the system disables write caching by
default. It does this so the devices can be removed without loss
of data. When write caching is disable, however, the system
will likely experience slower performance, so be sure to enable
write caching when you have finished removing the device.
How to unplug or eject devices
ꢂꢁ
1. In the notification area next to your task bar, double-click the
Safe Removal icon. Safe removal displays a list of Plug and
Play devices that support safe removal and that are currently
attached to the system. If you do not see the Safe Removal
icon, your device does not support safe removal, and you
cannot unplug or eject your device using Safe Removal.
2. In Safely Remove Hardware, in the list of devices, select the
device that you want to unplug or eject, and then click Stop.
This tells the system that you will be unplugging or ejecting
the device.
3. In Stop a Hardware device, click OK.
A notification appears stating that it is now safe to unplug or
eject the device.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A W476 Specifications
This appendix lists technical and hardware specifications of
your W476 notebook computer. Please note that the information
mentioned here may not completely match your notebook
computer’s actual specifications. Specification is subject to change
without notice, and the present manual may be modified at a later
time.
ꢂꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
Microprocessor
Connectivity
• Intergrated 10/100 Mbps Fast Ethernet connection
• Built-in 56Kbps V.92 fax/data modern
• Three Universal Serial Bus (USB) 2.0 ports
• Dual band antenna Intel® Wireless LAN Shirley Peak (1x2) a/g/n
(Intel® WiFi Link 5100) (Option)
• Intel® Centrino® 2 Processor Technology
• 45nm Intel® Core™2 Duo processor (Penryn) 2.26G~2.8G
• Intel® Celeron® processor (Montevina)
• PGA package478pin, Socket P
• 1066MHz FSB
Audio
Core Logic
• Built-in High Definition Audio
• Intel® PM45/ ICH9M (W476V)
• Intel® GM45/ ICH9M (W476M)
• Built-in two stereo speakers Dual Array Microphone
• Separate audio ports for headphone-out and microphone-in
devices
Memory
•
512MB to maximum 8GB 667/800MHz DDR2 SDRAM with two
SODIMM memory sockets
Keyboard and pointing devices
• 86-key US/87-key EU/90-key JP with Windows function keys
• Ergonomically-centered touchpad pointing device with scroll
function
• 1 MB flash ROM BIOS
Data Storage
• SATA hard disk, 5400 rpm, available in 160GB/250GB/320GB
• One modularized 5.25”/12.7mm slim DVD-COMBO/DVD-Dual/
Super Multi
I/O ports
• One e-SATA / USB2.0 combo Port
• One RJ-11 phone jack (V.92, 56Kbps modem)
• One RJ-45 network jack
ꢂꢃ
• 5-in-1 MS/ MS PRO/MS DUO/MMC/SD Card Reader
• One DC-in jack (AC adapter)
• One D-SUB
• One speaker/headphone-out jack (3.5mm mini jack)
• One MIC-in jack (3.5mm mini jack)
• One PCI Express Card
Graphics
• NVIDIA® Geforce 9300M GS 256MB (W476V)
• Intel® Graphics Media Accelerator (GMA 4500MHD) (W476M)
Display and Video
• 14.1” TFT-LCD, WXGA (1280x800), Glare Type
• Simulataneous LCD and CRT display support
• Dual indenpendent display
• One HDMI Port for W476V
• Two USB 2.0 Ports
Dimensions and Weight (with battery and optical drive)
• 14.1” display model; about 2.38kg (W476V), 2.36kg (W476M)
• 338(W)x239(D)x29.8~38.4(H) mm
Power: 90W AC adapter, 19V 4.74A (W476V)
65W AC adapter, 19V 3.42A (W476M)
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B W576 Specifications
This appendix lists technical and hardware specifications of
your W576 notebook computer. Please note that the information
mentioned here may not completely match your notebook
computer’s actual specifications. Specification is subject to change
without notice, and the present manual may be modified at a later
time.
ꢂꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
Microprocessor
Connectivity
• Intergrated 10/100/1000 Mbps Fast Ethernet connection
• Built-in 56Kbps V.92 fax/data modern
• Three Universal Serial Bus (USB) 2.0 ports
• Dual band antenna Intel® Wireless LAN Shirley Peak (1x2) a/g/n
(Intel® WiFi Link 5100) (Option)
• Intel® Centrino® Processor Technology
• 45nm Intel® Core™2 Duo processor (Penryn) 2.26G~2.8G
• Intel® Celeron® processor (Montevina)
• PGA package478pin, Socket P
• 1066MHz FSB
Audio
Core Logic
• Built-in High Definition Audio
• Intel® PM45/ ICH9M (W576V)
• Intel® GM45/ ICH9M (W576M)
• Built-in two stereo speakers Dual Array Microphone
• Separate audio ports for headphone-out and microphone-in
devices
Memory
•
512MB to maximum 8GB 667/800MHz DDR2 SDRAM with two
SODIMM memory sockets
Keyboard and pointing devices
• 86-key US/87-key EU/90-key JP with Windows function keys
• Ergonomically-centered touchpad pointing device with scroll
function
• 1 MB flash ROM BIOS
• 2GB
®
or
4GB Intel Turbo Memory (Option)
Data Storage
I/O ports
• SATA hard disk, 5400 rpm, available in 160GB/250GB/320GB
• One modularized 5.25”/12.7mm slim DVD-COMBO/DVD-Dual/
Super Multi
• One e-SATA / USB2.0 combo Port
• One RJ-11 phone jack (V.92, 56Kbps modem)
• One RJ-45 network jack
• One DC-in jack (AC adapter)
• One D-SUB
• One speaker/headphone-out jack (3.5mm mini jack)
• One MIC-in jack (3.5mm mini jack)
• One PCI Express Card
ꢂꢅ
• 5-in-1 MS/ MS PRO/MS DUO/MMC/SD Card Reader
Graphics
• NVIDIA® Geforce 9600M GS 512MB (W576V)
• Intel® Graphics Media Accelerator (GMA 4500MHD) (W576M)
Display and Video
• One HDMI Port
• Two USB 2.0 Ports
• 15.4” TFT-LCD, WXGA (1280x800), Glare Type
• Simulataneous LCD and CRT display support
• Dual indenpendent display
Dimensions and Weight (with battery and optical drive)
• 15.4” display model; about 2.66kg (W576V), 2.6kg (W576M)
• 357(W)x257(D)x29.8~38.8(H) mm
Power: 90W AC adapter, 19V 4.74A (W576V)
65W AC adapter, 19V 3.42A (W576M)
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Service Centers
This appendix will list our global service centers for your W476 /
W576 notebook computer.
ꢂꢈ
Download from Www.Somanuals.com. All Manuals Search And Download.
W476 / W576 NOTEBOOK SERIES USER’S MANUAL
Wuhan
Taiwan (Headquarters) GIGA-BYTE TECHNOLOGY CO., LTD.
TEL: +86-27-87851312
FAX: +86-27-87851330
Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei 231, Taiwan
TEL: +886 (2) 8912-4000
FAX: +886 (2) 8912-4004
Xian
TEL: +86-29-85531943
FAX: +86-29-85519336
Shenyang
TEL: +86-24-83992901
FAX: +86-24-83992909
U.S.A. G.B.T. INC.
Shen Zhen
TEL: +86-755-82408099
FAX: +86-755-82408066
TEL: +1 (626) 854-9338
FAX: +1 (626) 854-9339
Ningbo
TEL: +86-574-86869292
FAX: +86-574-86860781
ꢂꢇ
China
G.B.T. TECH. TRADING CO., LTD.
Russia
Moscow Representative Office of Giga-Byte Technology Co., Ltd.
Guangzhou
TEL: +86-20-87540700
FAX: +86-20-87544306
TEL: +7-495-9136685
Beijing
TEL: +86-10-62102838
FAX: +86-10-62102848
Germany
HAMBURG Representative Office of Giga-Byte Technology Co.,
Ltd.
Chengdu
TEL: +86-28-85236930
FAX: +86-28-85256822
TEL: +49 40 25330433
Address: BULLENKOPPEL 16 22047 HAMBURG
Download from Www.Somanuals.com. All Manuals Search And Download.
|