Intel Computer Hardware LXD972M User Manual

Intel® LXD972M Transceiver  
Demo Board (Board Rev A1)  
Preliminary User’s Guide  
October 2004  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Contents  
Features of Intel® LXD972M Demo Board............................................................................6  
2.0 Using the Intel® LXD972M Demo Board .........................................................................................7  
2.4.1 Optional Test Setup, Using Two Intel® LXD972M Demo Boards ..........................11  
3.0 Intel® LXD972M Demo Board Schematics....................................................................................15  
Figures  
Intel® LXD972M Transceiver Demo Board ................................................................................10  
Schematic: Intel® LXD972M Transceiver Demo Board Power Control ......................................16  
Schematic: Intel® LXD972M Transceiver Demo Board MII Port.................................................17  
Schematic: Intel® LXD972M Transceiver Demo Board Twisted-Pair Port..................................18  
Schematic: Intel® LXD972M Transceiver Demo Board Configuration........................................19  
Tables  
Preliminary User’s Guide  
3
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Revision History  
Revision Number 002  
Revision Date: October 2004  
Page  
Description  
Section 1.3, “Features of Intel® LXD972M Demo Board”. Text changed.  
Figure 2 “Intel® LXD972M Transceiver Demo Board” changed.  
Section 2.4.5, “CFG Pin Configuration Options”. Text changed and new table added.  
Section 3.0, “Intel® LXD972M Demo Board Schematics”. Schematics changed.  
Revision Number 001  
Revision Date: July 2004  
Page  
Description  
Initial release.  
4
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
1.0  
Introduction  
This document describes the typical hardware set-up procedures for the Intel® LXD972M  
Transceiver Demo Board (called hereafter the LXD972M Demo Board). The LXD972M Demo  
Board is a platform for evaluation of the Intel LXT972M Single-Port 10/100 Mbps PHY  
Transceiver (called hereafter the LXT972M Transceiver).  
The LXD972M Demo Board allows system designers to test the following:  
10 Mbps and 100 Mbps link performance  
Auto-negotiation  
Register functionality  
The LXD972M Demo Board requires only a single 3.3V power supply.  
1.1  
1.2  
About this Demo Board Kit  
This Demo Board kit includes the following:  
LXD972M Demo Board  
Intel® LXD972M Transceiver Demo Board (Board Rev A1) User’s Guide  
Related Documents  
Table 1 lists related documentation.  
Table 1. Related Documents  
Document  
Document Number  
Intel® LXT972M Single-Port 10/100 Mbps PHY Transceiver Datasheet  
302875  
Intel® LXT971A, LXT972A, LXT972M Single-Port 10/100 Mbps PHY Transceivers  
Specification Update  
249354  
Preliminary User’s Guide  
5
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
1.3  
Features of Intel® LXD972M Demo Board  
3.3V operation, with option for 2.5V I/O voltage  
Low power consumption (300 mW typical)  
Quick setup and clear visibility of application settings for complete system demonstration  
Auto-negotiation protocol compliant. Compatible with systems not supporting auto-  
negotiation.  
LED indicators for major functions  
JTAG boundary scan port  
Configurable through MDIO port or hardware jumpers  
Standard half-duplex or full-duplex operation at 10 Mbps or 100 Mbps  
6
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
2.0  
Using the Intel® LXD972M Demo Board  
This document includes information on the following items concerning using the LXD972M Demo  
Board:  
Chapter 3.0, “Intel® LXD972M Demo Board Schematics”  
2.1  
Equipment Requirements  
The LXD972M Demo Board is populated with all components needed for twisted-pair evaluation.  
However, the following additional equipment is also required:  
SmartBits Advanced Multi-port Performance Test Box configured with firmware version 4.39  
or newer  
PC with Smart Windows (version 6.0 or newer) installed  
One MII Cable (male to male)  
One external NIC card  
One Category 5 Unshielded Twisted-Pair (UTP) crossover cable  
External power supply  
Preliminary User’s Guide  
7
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
2.2  
Typical Test Setup  
Figure 1 shows a typical test setup for standard operation of the LXD972M Demo Board.  
The LXD972M Demo Board plugs into a SmartBits Advanced Performance Test Box through a  
standard 40-pin MII cable (not included with the LXD972M Demo Board). The LXD972M Demo  
Board RJ-45 jack connects to the RJ-45 card in the SmartBits test box through a Twisted-Pair  
cable. Operation can be set for evaluation of 10 Mbps, 100 Mbps, and auto-negotiation capabilities.  
Figure 1. Typical Test Setup  
Computer with  
Smart Windows  
SmartBits  
Advanced Multi-port  
RS-232  
Performance  
Tester  
RJ-45 Card  
or  
External NIC Cards  
MII  
Cards  
MII Cables  
MII  
Connectors  
Twisted Pair  
Crossover  
Cable  
LXD972M  
LXT972M  
B3570-03  
8
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
2.3  
Quick-Start Checklists  
Use the quick-start checklists in this section to set up the LXD972M Demo Board, shown in Figure  
2, “Intel® LXD972M Transceiver Demo Board” on page 10.  
The following quick-start setup procedure sets all ports to the default condition, which includes  
Auto-Negotiation enabled, advertising dual-speed, and full-duplex/half-duplex capabilities.  
1. Set the jumpers as listed in Table 2.  
The following jumpers are defined as follows: LED1 has the functionality of LED/CFG1,  
LED2 has the functionality of LED/CFG2, and CFG has the functionality of LED/CFG3 as  
defined by the LXT972M Transceiver datasheet.  
2. Set SW1 switches as listed in Table 3.  
3. Connect the MII port of the LXD972M Demo Board to the Smartbits test box through the MII  
connector/cable. A male-to-male cable is required to interface the Smartbits test box to the  
LXD972M Demo Board and is available from Newark* (.5m cable - Newark 91F9746).  
4. Connect the twisted-pair port through a Twisted-Pair crossover cable to the RJ-45 card in the  
SmartBits test box.  
5. Power up the Smartbits test box.  
6. When the LXD972M Demo Board is configured according to desired test settings, apply the  
desired power connections per Table 4 options in Section 2.4.2, “Power Supply Voltage Source  
and Clock Options” on page 12 and press Reset switch S2.  
7. Proceed with testing.  
Table 2. Quick-Start Checklist for Jumper Settings  
Jumper  
Label  
Setting  
Configuration  
JP1,  
JP2,  
JP3  
LED1,  
LED2,  
CFG  
"Sets Port Configuration to 111 for Auto-Negotiation,  
Jumper 10/100 Mbps, Full-Duplex. For details, see Section  
Pins 1, 2  
Routes power from VCCD connector (BN4) through  
JP12 to the VCCA input.  
JP12  
VCCA  
Jumpered  
JP16  
JP17  
MDIO  
MDC  
Pins 2, 3  
Pins 2, 3  
Pins 1, 2  
Jumper Routes MDIO through MII 40-pin Connector P1.  
Jumper Routes MDC through MII 40-pin Connector P1.  
Open  
Disables output of clock oscillator Y2.  
JP18  
JP19  
Clock Select  
Reset  
Pins 3, 4  
Pins 5, 6  
Jumper  
Jumper  
Connects crystal across XI and XO to enable Y1.  
Pins 1,2  
Jumper Connects reset button  
Table 3. Quick-Start Checklist for Switch Settings  
Switch / Label  
SW1-1 / ID EN  
Setting  
Configuration  
Off  
Off  
Off  
Off  
Not applicable for LXT972M Transceiver.  
Sets ADDR0 = 0 (“Off” position)  
SW1-2 / ADDR0  
SW1-3 / ADDR1  
Sets ADDR1 = 0 (“Off” position)  
SW1-4 / LINKHOLD / RBIAS  
Not applicable for LXT972M Transceiver.  
Preliminary User’s Guide  
9
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Figure 2. Intel® LXD972M Transceiver Demo Board  
SILKSCREEN TOP  
BOARD ID  
SERIAL #  
B3798-001  
Note: In Figure 2, the format of the Board ID on the LXD972M Transceiver Demo Board can be either  
one of the following:  
For leaded: LXD972M Rev.A1  
For lead-free: LXD972MLF Rev.A1  
In Figure 2, the format of the Serial Number on the LXD972M Transceiver Demo Board can be  
either one of the following:  
For leaded: 972M-xxxx-A1  
For lead-free: 972MLF-xxxx-A1  
10  
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
2.4  
Configurations  
2.4.1  
Optional Test Setup, Using Two Intel® LXD972M Demo Boards  
Figure 3 shows an optional test setup using two LXD972M Demo Boards. Each Demo Board plugs  
into a SmartBits Advanced Performance Test Box through standard 40-pin MII cables. The two  
LXD972M Demo Boards are linked through a Twisted-Pair crossover cable connected to the RJ-45  
jack on each board. Operation can be set for evaluation of 10 Mbps, 100 Mbps, and auto-  
negotiation capabilities.  
Figure 3. Optional Test Setup  
Computer with  
Smart Windows  
SmartBits  
Advanced Multi-port  
RS-232  
Performance  
Tester  
MII  
Cards  
MII Cable  
MII  
MII  
Connector  
Connector  
LXD972M  
LXD972M  
LXT972M  
LXT972M  
RJ-45  
RJ-45  
Twisted-Pair  
Crossover  
Cable  
B3572-05  
Preliminary User’s Guide  
11  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
2.4.2  
Power Supply Voltage Source and Clock Options  
Table 4 lists banana lead power connectors (BNn) for the LXD972M Demo Board. For details on  
the power supplies, see the schematic in Chapter 3.0, “Intel® LXD972M Demo Board  
Table 4. Power Supply Voltage Source Connector Options  
Reference  
Designators  
Signal  
Supply Description  
+3.3V.  
BN1  
BN2  
BN3  
VCC  
GND  
For components on the LXD972M Demo Board other than LXT972M Transceiver.  
Ground  
+3.3V or +2.5V.  
VCCIO  
I/O voltage for the LXT972M Transceiver.  
+3.3V.  
BN4  
VCCD  
LXT972M digital power. If JP12 jumper is on, analog power is provided for the  
LXT972M Transceiver.  
Table 5 lists internal and external jumper settings to configure the power supply source for the  
transmit magnetic center-tap voltage.  
Table 5. Magnetic Center-Tap Voltage Source Configuration Options  
Desired  
Power Supply Source  
Setting  
Description  
3.3V Power Supply from  
VCCA  
Jumper  
JP4  
Use Jumper JP4 to apply 3.3V power from VCCA for center-tap  
operation.  
Ope n  
JP4  
Use Jumper JP4 to supply either 2.5V or 3.3V power supply for  
center-tap operation. Connect the power supply to pin 2 of JP4.  
Alternate Power Supply  
Table 6 lists the LXT972M Demo Board analog power supply (VCCA) configuration options.  
Table 6. Analog Power Supply (VCCA) Configuration Options  
Desired  
Configuration  
Setting  
Description  
3.3V Power  
Supply to VCCA  
Jumper Use Jumper JP12 to route power from the VCCD Power Connector  
JP12  
(BN4) through JP12 to the VCCA input of the LXT972M Transceiver.  
1. Remove jumper from JP12 to disable for VCCA input.  
2. Apply external power from an alternate power supply through  
pin 2 of JP12. For power supply requirements, see the LXT972M  
Transceiver datasheet.  
Analog  
External Power  
Supply to VCCA  
Open  
JP12  
12  
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Table 7 lists clock configuration options.  
Table 7. Clock Configuration Options  
Desired  
JP18 Settings  
Configuration  
Description  
Remove jumper from pins 1 and 2 to disable the clock oscillator Y2  
output.  
Pins 11, 2  
Open  
Enable Crystal  
Oscillator Y1  
Pins 3, 4  
Pins 5, 6  
Place a jumper on pins 3 and 4 and pins 5 and 6, which connects a  
crystal across XI and XO to enable Y1.  
Jumper  
Place a jumper on pins 1 and 2, which enables the output of clock  
oscillator Y2.  
Pins 1, 2 Jumper  
Enable Clock  
Oscillator Y2  
Pins 3, 4  
Open  
Pins 5, 6  
Remove jumper from pins 3 and 4, and remove jumper from pins 5  
and 6, which disables a crystal connection across XI and XO to Y1.  
1. Pin 1 is located on the lower-right corner of JP18.  
2.4.3  
MDIO Configuration Options  
The default configuration of the MDIO and MDC signals is to route the MDIO through the MII  
connector to the SmartBits Test Box by installing jumpers JP16 and JP17.  
Note: The RJ-11 feature is not supported. As a result, do not jumper the MDIO and MDC signals to the  
RJ-11 connector.  
Table 8 lists the desired MDIO configuration settings.  
Table 8. MDIO Configuration Options  
Desired Configuration  
Jumper  
Setting  
Description  
JP16  
JP17  
JP16  
JP17  
Jumper Pins 2, 3  
Jumper Pins 2, 3  
Jumper Pins 1, 2  
Jumper Pins 1, 2  
Routes MDIO through 40-pin MII Connector P1  
Routes MDC through 40-pin MII Connector P1  
Routes MDIO through RJ-11 Connector J2  
Routes MDC through RJ-11 Connector J2  
Route MDIO and MDC  
through MII  
Route MDIO and MDC  
through RJ-11  
2.4.4  
LED Configuration Options  
The LXD972M Demo Board provides three programmable LEDs. Each LED can display one of  
several available status conditions as selected by the LED Configuration Register (Address 20).  
Programmable LEDs (LED/CFG1, LED/CFG2, LED/CFG3) are set in default mode and are  
programmable with the MDIO pin. Register address 20 also provides optional LED pulse  
stretching up to 100 ms. Register bits 20.3:2 select one of three possible stretch times. (For details,  
see the LXT972M Transceiver datasheet.)  
Note: The active LED state is determined by the CFG pin function. When the LED/CFG pin is pulled  
High, the LED becomes active Low. When the LED/CFG pin is pulled Low, the LED becomes  
active High.  
Preliminary User’s Guide  
13  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
2.4.5  
CFG Pin Configuration Options  
Three control jumpers pull the associated port configuration pins High or Low to select the desired  
mode (auto-negotiation, speed, and duplex). When auto-negotiation is enabled with LED/CFG1  
(JP1) = 1, then LED/CFG2 (JP2), and LED/CFG3 (JP3) are used to configure default advertising  
characteristics of the LXD972M Demo Board. The desired modes and jumper configuration  
settings are listed in Table 9. For specific register definitions and functions, see the LXT972M  
Transceiver datasheet.  
Table 9. Jumper Configuration Settings for LED/CFG Pins  
Mode  
Jumper Settings  
JP1  
LED/CFG1  
Setting  
JP2  
LED/CFG2  
Setting  
JP3  
LED/CFG3  
Setting  
Auto-  
Negotiation  
Speed Duplex  
Half  
Pins 2 & 3  
Pins 2 & 3  
Pins 2 & 3  
Pins 1 & 2  
Pins 1 & 2  
Pins 2 & 3  
10  
Full  
Pins 2 & 3  
Pins 2 & 3  
Pins 2 & 3  
Pins 1 & 2  
Pins 1 & 2  
Pins 2 & 3  
Pins 1 & 2  
Pins 2 & 3  
Disabled  
Half  
100  
Full  
Half  
Pins 2 & 3  
Pins 2 & 3  
Pins 1 & 2  
Pins 1 & 2  
Jumper  
Jumper  
Jumper  
100  
Full /  
Half  
Pins 1 & 2  
Pins 1 & 2  
Pins 1 & 2  
Pins 1 & 2  
Pins 2 & 3  
Pins 1 & 2  
Enabled  
Half  
10/100  
Full /  
Half  
2.5  
JTAG Test Signals  
The boundary scan test port is accessed through JP14 for board level testing. Table 10 lists the  
JTAG test signal descriptions.  
Table 10. JTAG Test Signal Descriptions  
JP14 Pin  
Symbol  
Number  
Description  
1
3
5
7
8
TRST_L Test Reset. Test reset input sourced by testing device.  
TCK  
TMS  
TDO  
TDI  
Test Clock. Test clock input sourced by testing device.  
Test Mode Select.  
Test Data Output. Test data driven with respect to the falling edge of TCK.  
Test Data Input. Test data sampled with respect to the rising edge of TCK.  
14  
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
3.0  
Intel® LXD972M Demo Board Schematics  
This section includes schematics for the LXD972M Demo Board:  
Figure 4, “Schematic: Intel® LXD972M Transceiver Demo Board Power Control” on page 16  
Figure 5, “Schematic: Intel® LXD972M Transceiver Demo Board MII Port” on page 17  
Figure 6, “Schematic: Intel® LXD972M Transceiver Demo Board Twisted-Pair Port” on  
Figure 7, “Schematic: Intel® LXD972M Transceiver Demo Board Configuration” on page 19  
Note: Page 1 of 5 of the schematics is not included (the title page of the schematics).  
Preliminary User’s Guide  
15  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Figure 4. Schematic: Intel® LXD972M Transceiver Demo Board Power Control  
1
1
C V C A  
1
1
C V C A  
C V C D  
G N D A  
1 3  
1 6  
3 9  
G N D D  
3 8  
O
O
C V C I  
C V C I  
O
O
O
G N D I  
G N D I  
G N D I  
2 9  
6
3 0  
9
5
1
16  
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Figure 5. Schematic: Intel® LXD972M Transceiver Demo Board MII Port  
1
T P 4 3  
1
T P 4 2  
1
T P 4 1  
X
X
X
X
X
R 8 1  
R 8 0  
R 7 9  
R 7 8  
R 7 7  
1
T P 2 2  
1
T P 2 1  
1
T P 2 0  
1
T P 1 9  
1
T P 1 8  
1
T P 3 0  
1
1
T P 1 7  
T P 2 9  
T P 2 8  
1
1
T P 1 6  
1
T P 2 7  
1
1
T P 1 5  
T P 2 6  
1
T P 2 5  
1
T P 2 4  
C
V C  
G N D  
1 0  
2 0  
C
V C  
G N D  
1 0  
2 0  
Preliminary User’s Guide  
17  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Figure 6. Schematic: Intel® LXD972M Transceiver Demo Board Twisted-Pair Port  
+
|
+
|
+
|
+
|
18  
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Figure 7. Schematic: Intel® LXD972M Transceiver Demo Board Configuration  
1
1
1
1
1
1
Preliminary User’s Guide  
19  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
4.0  
Bill of Materials  
Table 11 lists the bill of materials for the LXD972M Demo Board Rev A1.  
Table 11. Bill of Materials (Sheet 1 of 3)  
Board Reference  
Description  
Manufacturer  
Part Number  
Quantity  
Designator  
CONN BANANA NUT  
SILVER (BANANA_NUT)  
BN1-4  
EF JOHNSON  
108-0740-001  
4
C1, C2, C5, C8, C9, C11,  
C13, C38-C42, C45, C46  
LABELS NOT USED IN SCHEMATIC.  
C3, C6, C10, C14-16,  
C50-51  
HEADER 3X1 (SIP\3P)  
BERG  
BERG  
AVX  
08055C104KATMA  
ECU-V1H102JCX  
08055C103KATMA  
X
8
4
2
1
5
4
HEADER 4X2  
(HEADER2X4)  
C4, C7, C12, C52  
C17, C49  
CAP 0.01uF X7R 10%  
(0805)  
C53 (NOT INSTALLED)  
C18, C47-48, C58-59  
C31, C34, C54, C56  
NOT INSTALLED  
CAP 1000pF 20% 2KV X7R  
(1812)  
AVX  
1812GC102KAT1A  
ECS-TOJY106R  
CAP 10uF 6.3V TANT  
(CASEA)  
PANASONIC  
C32-33  
CAP 18pF 50V 5% (0805)  
CAP 100uF 6.3V (CASED)  
CAP 20PF 50V 5% (1206)  
CAP 270pF NPO (1206)  
PANASONIC  
PANASONIC  
PANASONIC  
AVX  
ECU-V1H180JCN  
ECE-V0JA101P  
ECU-V1H200JCM  
12061A271JATTA  
2
3
1
2
C36, C55, C57  
C37  
C43-44  
DIODE RECTIFIER DL4001  
1A 50V MELF SMD  
D1  
DIODES INC.  
DL4001-13  
1
DIODE LED GREEN SS  
TYPE LOW CUR SMD  
(LED\SMD\SS)  
D2-D8  
PANASONIC  
BERG  
LNJ308G8LRA  
68000-240-2  
7
7
DTP1-4, JP4, JP12, JP19  
FB1, FB2  
HEADER 2X1 (SIP\2P)  
LABELS NOT USED IN SCHEMATIC.  
FBEAD 60 OHM@100MHZ  
0.10OHM@DC 1.5A (1210) STEWARD  
(BEAD3225)  
FB3-5  
MI1210K600R-00  
3
FB6 (NOT INSTALLED)  
J1  
NOT INSTALLED  
X
1
1
CONN MOD JACK 8-8  
AMP  
555164-1  
LOW PROFILE  
CONN MOD JACK 6-6  
J2  
J3  
RJ11 UNSHIELDED  
BLOCK RJ11-6L-B  
CORCOM  
RJ11-6L-B  
1
1
CONN SMB VERTICAL PC JOHNSON  
MOUNT (SMB\SM) COMPONENTS  
131-3711-201  
20  
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Table 11. Bill of Materials (Sheet 2 of 3)  
Board Reference  
Designator  
Description  
Manufacturer  
Part Number  
Quantity  
JP5-JP11, JP13, JP15  
LABELS NOT USED IN SCHEMATIC.  
JP1-3, JP16-17  
HEADER 3X1 (SIP\3P)  
BERG  
BERG  
BERG  
AMP  
68000-240-3  
C9192-280-4  
C9192-280-3  
787171-4  
5
1
1
1
HEADER 4X2  
(HEADER2X4)  
JP14  
JP18  
P1  
HEADER 3X2  
CONN MII 40 PIN FEMALE  
R/A (CON40F\RT\4ROW)  
RES 182 OHM 1/8W 1%  
(1206) SMD  
R1-3  
PANASONIC  
PANASONIC  
ERJ-8ENF1820V  
ERJ-8ENF49R9V  
3
R4-9, R12-13, R23-25,  
R27, R29, R31, R33, R35,  
R40-44, R46-47, R70,  
R76, R82, R83  
RES 49.9 1/8W 1% (1206)  
27  
R26, R28, R30, R32, R34, RES 22 OHM 1/8W 1%  
9C08052A22R0FK  
HFT  
YAGEO AMERICA  
PANASONIC  
10  
5
R36-38, R45, R48  
(0805)  
R58, R60-62, R66  
RES 4.7K 1/8W 5% (1206)  
ERJ-8GEYJ472V  
ERJ-8ENF1003V  
RES 100K 1/8W 1% (1206)  
SMD  
R65  
R67  
PANASONIC  
1
RES 10K 1/8W 1% (1206)  
NOTE: R3 is shown as 180  
Ohm resistor in  
PANASONIC  
PANASONIC  
ERJ-8ENF1002V  
1
schematic.  
RES 100 OHM 1/8W 1%  
(1206)  
R68  
R69  
R72  
ERJ-8ENF1000V  
ERJ-8ENF2212V  
ERJ-8GEYJ221V  
1
1
1
RES 22.1K 1/8W 1% (1206) PANASONIC  
RES 220 OHM 1/8W 5%  
PANASONIC  
(1206)  
R73, R75, R77-R82 (NOT  
INSTALLED)  
NOT INSTALLED  
X
8
R10, R11, R14-22, R39,  
R49-57, R59, R63-64, R71  
LABELS NOT USED IN SCHEMATIC.  
RES 0 OHM 1/8W 5%  
PANASONIC  
R74  
S2  
ERJ-8GEY0R00V  
KT11P2JM  
1
1
(1206) SMD  
SWITCH PB MOM KEY J-  
C&K  
LEAD SMD  
COMPONENTS  
(SWITCH\RESET\SM)  
SWITCH DIP 4 POS THRU  
SW1  
T1  
HOLE SEALED BLACK  
(SWITCH\8)  
AMP  
4-435166-9  
1
IC XFMR TG110-S050N2  
16 PIN SOIC  
HALO  
BERG  
TG110-S050N2  
68000-240-1  
1
TP2-5, TP15-22, TP24-30,  
TP34-43  
HEADER 1X1  
29  
Preliminary User’s Guide  
21  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Intel® LXD972M Transceiver Demo Board (Board Rev A1)  
Table 11. Bill of Materials (Sheet 3 of 3)  
Board Reference  
Designator  
Description  
Manufacturer  
Part Number  
Quantity  
TP1, TP6-14, TP23,  
TP31-33  
LABELS NOT USED IN SCHEMATIC.  
IC LOGIC 74LVC244 LOW  
TEXAS  
U1, U3  
VOLTAGE BUFFER 20 PIN  
SN74LVC244ADW  
LXT977/LXT972M  
2
1
INSTRUMENTS  
SOIC  
IC PHY LXT977/LXT972M  
DUAL PORT (LQFP48C)  
U2  
U4  
INTEL  
LABELS NOT USED IN SCHEMATIC.  
IC LOGIC 74LVX14 HEX  
SCHMITT TRIG INV 14 PIN TOSHIBA  
SOIC  
U5  
TC74LVX14FN  
1
CRYSTAL 25.000MHZ  
(HC49)  
Y1  
Y2  
CTS  
MP250  
1
1
OSC 25.000MHZ FULL  
SIZE ( )  
CTS  
MX045-25.0000  
22  
Preliminary User’s Guide  
Document Number: 303125  
Revision Number: 002  
Revision Date: October 22, 2004  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Washer IWE 6125 User Manual
Jackson Dishwasher Tempstar TGP User Manual
JAI Webcam TM 1400 User Manual
Jenn Air Refrigerator JCD2295KE User Manual
Jura Capresso Espresso Maker 65349R3 User Manual
JVC Sleep Apnea Machine DT V2000SU User Manual
JVC Stereo Amplifier KS AX4302 User Manual
JVC Stereo System 0410YOMMDWCDT User Manual
Keating Of Chicago Fryer 18 BB Electric User Manual
Kenmore Car Stereo System 79042003 User Manual