8I845PE-RZ /
8I845PE-RZ-C
Intel® Pentium® 4 Processor Motherboard
User's Manual
Rev. 1002
12ME-I845PERZ-1002
Copyright
© 2004GIGABYTETECHNOLOGYCO., LTD
CopyrightbyGIGA-BYTETECHNOLOGYCO.,LTD. ("GBT"). Nopartofthismanualmaybereproduced ortransmitted inanyfrom
withoutthe expressed,written permission ofGBT.
Trademarks
Third-partybrandsandnamesarethepropertyoftheirrespectiveowners.
Notice
Please do not remove anylabelson motherboard, thismayvoid the warrantyofthismotherboard.
Due to rapid change in technology, some of the specificationsmightbe outofdatebefore publication ofthisbooklet.
The authorassumesnoresponsibilityfor anyerrorsoromissionsthatmayappearin thisdocument nordoesthe authormake a
commitmentto updatetheinformationcontained herein.
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing Your Computer
Computer motherboards and expansion cards contain very delicate Integrated Circuit(IC) chips. To
protectthem againstdamagefrom static electricity, youshouldfollowsomeprecautions wheneveryou
work on your computer.
1. Unplug yourcomputer when working onthe inside.
2. Use agroundedwrist strap beforehandlingcomputer components.Ifyou do nothaveone,
touch both ofyour hands to a safelygrounded object or to a metal object, such as the power
supplycase.
3. Hold components bythe edges and trynottouch the IC chips, leads or connectors, or other
components.
4. Place components on agrounded antistatic pad or on thebag thatcame withthe components
whenever the componentsare separated from the system.
5. Ensure that theATX power supply is switched off before you plug inor remove the ATX power
connectoronthemotherboard.
Installing the motherboard to the chassis
Ifthe motherboard hasmounting holes, buttheydon'tline upwith the holes on the baseand there
are no slots to attach the spacers, do notbecome alarmed you can still attach the spacers to the
mounting holes. Justcut the bottom portion ofthe spacers (the spacer maybe a little hard to cutoff, so
be careful ofyour hands). In this wayyoucan stillattach the motherboard to the base withoutworrying
aboutshort circuits.Sometimes youmay need to use the plastic springs to isolate the screw from the
motherboard PCB surface,because the circuit wire maybe near bythe hole.Be careful, don't letthe
screw contactany printed circuit write or parts on the PCB thatare near the fixing hole, otherwise it
maydamagethe board orcauseboard malfunctioning.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter1 Introduction ................................................................................................5
FeaturesSummary...........................................................................................................................5
8I845PE-RZSeriesMotherboardLayout.........................................................................................6
BlockDiagram ..................................................................................................................................7
HardwareInstallation Process .........................................................................................................8
Step 1: Install the Central Processing Unit (CPU) ..........................................................................8
Step 1-1: CPU Installation .................................................................................................9
Step 1-2: CPU Cooling Fan Installation ............................................................................9
Step 2: InstallMemory Modules ....................................................................................................10
Step 3: Install AGP Card ............................................................................................................... 11
Step 4: Install I/O Peripherals Cables ........................................................................................... 11
Step 4-1: I/O Back Panel Introduction ............................................................................. 11
Step 4-2: Connectors Introduction ...................................................................................12
Chapter 2 BIOS Setup ............................................................................................. 19
The Main Menu (For example: BIOS Ver. : Fac) .........................................................................19
StandardCMOSFeatures .............................................................................................................21
Advanced BIOS Features .............................................................................................................23
IntegratedPeripherals .....................................................................................................................24
PowerManagementSetup .............................................................................................................26
PnP/PCIConfigurations .................................................................................................................28
PC Health Status............................................................................................................................29
Frequency/VoltageControl .............................................................................................................30
TopPerformance .............................................................................................................................31
LoadFail-SafeDefaults ...................................................................................................................32
LoadOptimizedDefaults .................................................................................................................32
SetSupervisor/User Password.....................................................................................................33
Save & Exit Setup .........................................................................................................................34
Exit Without Saving ........................................................................................................................34
Chapter 3 Install Drivers ........................................................................................... 35
8I845PE-RZ Series Motherboard
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
Features Summary
CPU
—
Socket 478 for Intel® Pentium® 4 (Northwood, Prescott (Note 1)) with HT
Technology
—
—
—
—
—
—
—
—
—
—
Intel® Pentium® 4 800(Note 2)/533/400M Hz FSB
2nd cache depends on CPU
Chipset
North Bridge: Intel® 82845PE M CH
South Bridge: Intel® 82801 (ICH4)
3 184-pin DDR DIMM sockets, supports up to 2GB DRAM (Max)
Supports DDR400(Note 3)/DDR333/DDR266 DIMM
Supports only 2.5V DDR SDRAM
1 AGP slot 4X (1.5V) device support
5 PCI slots support 33M Hz & PCI 2.2 compliant
2 IDE controller provide IDE HDD/CD-ROM(IDE1, IDE2) with PIO, Bus
Master (Ultra DM A33/ATA66/ATA100) operation modes
Can connect up to 4 IDE devices
1 Floppy portsupports 2 FDD with 360K, 720K,1.2M,1.44M and 2.88M bytes
1 Parallel port supports Norm al/EPP/ECP mode
2 Serial port (COMA/COM B)
6 USB 2.0/1.1 ports (2 x Rear, 4 x Front by cable)
1 Front Audio connector
1 PS/2 Keyboard
1 PS/2 Mouse
Builit-in RTL8100C chipset *
1 RJ45 port *
CM edia 9761A CODEC
Support 2/4/6 channel
Line Out / Line In / Mic In
Memory
Slots
On-Board IDE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
On-Board Floppy
On-Board Peripherals
On-Board LAN *
On-Board Sound
SPDIF Out /SPDIF In
CD In/ AUX_IN/ Game Port
Licensed AWARD BIOS
Supports Q-Flash™
BIOS
I/O Control
Hardware M onitor
ITE8712
CPU/System Fan Revolution detect
CPU/System Fan Fail Warning
CPU Overheat Warning
System Voltage Detect
Additional Features
Overclocking
Supports @BIOS™
Supports EasyTune 4™
Over Voltage (DDR/AGP/CPU) by BIOS
Over Clock (DDR/AGP/CPU) by BIOS
ATX size form factor, 29.5cm x 21cm
Form Factor
(Note1) Prescottprocessorswith upto 533MHzFSBaresupported.
(Note2) ANorthwood processorwith 800MHzFSB canbe supported through overclockingin BIOS.
(Note3) When 800MHzFSBisselected asprocessor frequency, memorywill automaticallyadjustto DDR400.
"*"For 8I845PE-RZ only.
- 5 -
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
8I845PE-RZ Series Motherboard Layout
21 cm
KB_MS
CPU_FAN
ATX
SOC KET 478
ATX_12V
SUR_CEN
F_AU DIO
Intel 845PE
FDD
AGP
RTL8100C
*
PCI1
PCI2
CLR_CMOS
SYS_FAN
CODEC
CD_IN
Intel IC H4
PCI3
AUX_IN
BAT
PCI4
PCI5
BIOS
IDE2
IDE1
F_U SB2
F_U SB1
SPDIF_IO
CI
PWR_LED
F_PANEL
"*"For 8I845PE-RZ only.
"#"For8I845PE-RZ-C only.
8I845PE-RZ Series Motherboard
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Block Diagram
Pentium 4
Socket 478
CPU
CPUCLK+/- (100/133MHz)
AGP 4X
AGPCLK
(66MHz)
System Bus
400/533MHz
DDR
266/333MHz
GMCHCLK(66MHz)
Intel 845PE
HCLK+/- (100/133MHz)
5 PCI
RJ45 *
66MHz
33 MHz
14.318 MHz
48 MHz
RTL8100C *
BIOS
ICH4
Game Port
Floppy
AC97 Link
LPC BUS
24 MHz
IT8712
LPT Port
AC97
PS/2
PCICLK
CODEC
KB/Mouse
(33MHz)
33 MHz
6 USB
Ports
ATA33/66/100
IDE Channels
COM
Ports
GMCH CLK(66MHz)
CPUCLK+/- (100/133MHz)
AGPCLK (66MHz)
PCICLK (33MHz)
USBCLK (48MHz)
14.318 MHz
CLK GEN
HCLK+/- (100/133MHz)
33 MHz
"*"For 8I845PE-RZ only.
- 7 -
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation Process
To set up your computer, you must complete the following steps:
Step 1- Install the Central Processing Unit (CPU)
Step 2- Install mem ory modules
Step 3- Install expansion cards
Step 4- Connect ribbon cables, cabinet wires, and power supply
Step 4
Step 1
Step 2
Step 4
Step 3
Step 4
Step 1: Install the Central Processing Unit (CPU)
Before installing the processor, adhere to the following warning:
1. Please m ake sure the CPU type is supported by the m otherboard.
2. The processor will overheat without the heatsink and/or fan, resulting in perm anent
irreparable damage.
3. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause im proper
installation. Please change the insert orientation.
4. Apply thermal grease between the processor and cooling fan.
5. Never run the processor without the heatsink properly and firmly attached. Perm anent
damage will result.
6. Please set the CPU host frequency in accordance with your processor's specifications.
We don't recomm end you to set the system bus frequency over the CPU's specification
because these specific bus frequencies are not the standard specifications for CPU,
chipset and most of the peripherals. Whether your system can run under these specific
bus frequencies properly will depend on your hardware configurations, including CPU,
Memory, Cards… etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your com puter system
requires all of the following platform components:
- CPU: An Intel® Pentium 4 Processor with HT Technology
- Chipset: An Intel® Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optim izations for HT Technology
8I845PE-RZ Series Motherboard
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1-1: CPU Installation
Figure 1.
Socket
Actuation
Lever
Pull the rod to the 90-degree directly.
Figure 2.
Locate Pin 1 in the socket and look for a (golden) cut edge on the
CPU upper corner. Insert the CPU into the socket. (Do not force the
CPU into the socket.) Then m ove the socket lever to the locked
position while holding pressure on the center of the CPU.
Step 1-2: CPU Cooling Fan Installation
Figure 1.
Apply the therm al tape(or grease) to provide better heat conduction
between your CPU and cooling fan.
Figure 2.
Fasten the cooling fan supporting-base onto the CPU socket on the
motherboard.
Figure 3.
Make sure the CPU fan is plugged to the CPU fan connector, than
install complete.
- 9 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Install Memory Modules
Before installing the m emory modules, adhere to the following warning:
1. Please note that the DIMM module can only fit in one direction due to the one notch.
Wrong orientation will cause im proper installation. Please change the insert orientation.
2. Due to (Intel 845PE/GE) chipset architecture limitation, a FSB 533 Pentium 4 processor
will support DDR333/DDR266 memory m odule. A FSB 400 Pentium 4 processor will
only support DDR266 memory module.
The motherboard has 3 dual inline memory m odule (DIM M) sockets. The BIOS will automatically
detects memory type and size. To install the memory module, just push it vertically into the DIMM
socket. The DIM M module can only fit in one direction due to the notch. M emory size can vary between
sockets.
Notch
DDR
1. The DIMM socket has a notch, so the DIMM
memory module can only fit in one direction.
2. Insert the DIMM mem ory module vertically into
the DIM M socket. Then push it down.
3. Close the plastic clip at both edges of the DIMM
sockets to lock the DIM M m odule.
Reverse the installation steps when you wish to
rem ove the DIM M module.
8I845PE-RZ Series Motherboard
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Install AGP Card
1. Read the relateAGP card's instruction documentbefore install the AGP card into the computer.
2. If your AGP card has "AGP 4X(1.5V) notch" (show below), please make sure your AGP card is AGP
4X(1.5V).
3. Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to
install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firm ly
down on the slot .M ake sure your AGP card is locked by the sm all white- drawable bar.
Step 4: Install I/O Peripherals Cables
Step 4-1: I/O Back Panel Introduction
v
y
u
}*
w
x
~
{
z
|
u
v
PS/2 Keyboard and PS/2 Mouse connector
This connector supports standard PS/2 keyboard and PS/2 m ouse.
Parallel port (LPT)
Device like printer can be connected to Parallel port.
w/x Serial port (COMA/COMB)
Mouse and modem etc. can be connected to Serial port.
y
z
{
Game/MIDIport
This connector supports joystick, M IDI keyboard and other relate audio devices.
Line Out jack
Connect the stereo speakers or earphone to this connector.
Line In jack
Devices like CD-ROM , walkm an etc. can be connect to Line In jack.
"*"For 8I845PE-RZ only.
- 11 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
|
MIC In jack
Microphone can be connect to MIC In jack.
After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software
selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to
"Line In" jack and connect "Center/Subwoofer" to "MIC In" jack.
LAN port *
LAN is fast Ethernet with 10/100M bps speed.
USB port
}
~
Before you connect your device(s) into USB connector(s), please make sure your device(s)
such as USB keyboard, mouse, scanner, zip, speaker...etc. Have a standard USB interface.
Also m ake sure your OS supports USB controller. If your OS does not support USB controller,
please contact OS vendor for possible patch or driver upgrade. For more information please
contact your OS or device(s) vendors.
Step 4-2: Connectors Introduction
3
1
2
6
10
9
16
12
11
4
17
5
13
7
14 15
8
1) ATX_12V
2) ATX
10) SUR_CEN
11) CD_IN
3) CPU_FAN
4) SYS_FAN
5) IDE1 / IDE2
6) FDD
12) AUX_IN
13) SPDIF_IO
14) CI
15) F_USB1 / F_USB2
16) CLR_CMOS
17) BAT
7) PWR_LED
8) F_PANEL
9) F_AUDIO
"*"For 8I845PE-RZ only.
8I845PE-RZ Series Motherboard
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1) ATX_12V (+12V Power Connector)
This connector (ATX_12V) supplies the CPU operation voltage (Vcore).
If this "ATX_12V connector" is not connected, system cannot boot.
Pin No.
Definition
GND
4
3
2
1
2
3
4
GND
+12V
+12V
1
2) ATX(ATX Power)
AC power cord should only be connected to your power supply unit after ATX power cable and
other related devices are firmly connected to the mainboard.
Pin No. Definition
Pin No. Definition
1
11
1
2
3
4
5
6
7
8
9
10
3.3V
11
12
13
14
15
16
17
18
3.3V
3.3V
-12V
GND
GND
VCC
PS_ON(softon/off)
GND
GND
GND
GND
-5V
VCC
GND
PowerGood
20
10
5VSB (stand by +5V) 19
+12V 20
VCC
VCC
3) CPU_FAN (CPU Fan Connector)
Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running
under abnormal condition or damaged by overheating. The CPU fan connector supports Max.
current up to 600 m A.
Pin No.
Definition
GND
1
2
3
1
+12V
Sense
- 13 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
4) SYS_FAN (System Fan Connector)
This connector allows you to link with the cooling fan on the system case to lower the system
temperature.
Pin No.
Definition
GND
1
2
3
1
+12V
Sense
5) IDE1 / IDE2 (IDE1 / IDE2 Connector)
Im portant Notice: Please connect first hard disk to IDE1 and connect CD-ROM to IDE2. The red
stripe of the ribbon cable must be the sam e side with the Pin1.
IDE2
IDE1
39
40
1
2
6) FDD (Floppy Connector)
Please connect the floppy drive ribbon cables to FDD. It supports 360K, 1.2M, 720K, 1.44M and
2.88M bytes floppy disk types.
The red stripe of the ribbon cable must be the sam e side with the Pin1.
34
33
2
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1
8I845PE-RZ Series Motherboard
7) PWR_LED
PWR_LED is connect with the system power indicator to indicate whether the system is on/off.
It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn
to another color.
Pin No.
Definition
MPD+
MPD-
1
2
3
1
MPD-
8) F_PANEL (2 x 10 pins Connector)
Please connect the power LED, PC speaker, reset switch and power switch etc of your chassisfront
panel to the F_PANEL connector according to the pin assignment below.
Soft Po we r
Con nector
Sp eaker Co nne ctor
Messa ge L ED/
Po we r/
Slee p LED
IDE Ha rd Disk Active LED
Reset Switch
HD (IDEHard DiskActive LED)
SPK(SpeakerConnector)
Pin 1:LED anode(+)
Pin2:LEDcathode(-)
Pin1:VCC(+)
Pin 2-Pin 3:NC
Pin4:Data(-)
RES(ResetSwitch)
Open:NormalOperation
Close:ResetHardwareSystem
Open:NormalOperation
Close:PowerOn/Off
Pin 1:LED anode(+)
Pin2:LEDcathode(-)
NC
PW(SoftPowerConnector)
MSG (MessageLED/Power/Sleep LED)
NC
- 15 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
9) F_AUDIO (Front Audio Connector)
If you want to use Front Audio connector, you must rem ove 5-6, 9-10 Jumper.
In order to utilize the front audio header, your chassis must have front audio connector. Also please
make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To
find out if the chassis you are buying support front audio connector, please contact your dealer.
Please note, you can have the alternative of using front audio connector or of using rear audio
connector to play sound.
Pin No.
Definition
MIC
1
2
3
4
5
6
7
8
9
10
GND
REF
Power
10
2
9
1
FrontAudio (R)
RearAudio (R)
Reserved
No Pin
FrontAudio (L)
RearAudio (L)
10) SUR_CEN (Surround Center Connector)
Please contact your nearest dealer for optional SUR_CEN cable.
Pin No.
1
Definition
SUROUTL
SUROUTR
GND
6
2
5
1
2
3
4
5
6
No Pin
CENTER_OUT
BASS_OUT
11) CD_IN (CD In Connector)
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No.
Definition
CD-L
1
2
3
4
1
GND
GND
CD-R
8I845PE-RZ Series Motherboard
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
12) AUX_IN (AUX In Connector)
Connect other device(such as PCI TV Tunner audio out)to the connector.
Pin No.
Definition
AUX-L
GND
1
2
3
4
1
GND
AUX-R
13) SPDIF_IO (SPDIF In/Out Connector)
The SPDIF output is capable of providing digital audio to external speakers or com pressed AC3
data to an external Dolby Digital Decoder. Use this feature only when your stereo system has
digital input function. Be careful with the polarity of the SPDIF_IO connector. Check the pin
assignment carefully while you connect the SPDIF_IO cable, incorrect connection between the
cable and connector will m ake the device unable to work or even dam age it. For optional
SPDIF_IO cable, please contact your local dealer.
Pin No.
Definition
VCC
1
2
3
4
5
6
2
1
6
5
No Pin
SPDIF
SPDIFI
GND
GND
14) CI (CASE OPEN)
This 2-pin connector allows your system to enable or disable the "Case Open" item in BIOS, if the
system case begin rem ove.
Pin No.
Definition
Signal
GND
1
2
1
- 17 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
15) F_USB1 / F_USB2 (Front USB Connector)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while
you connect the front USB cable, incorrect connection between the cable and connector will m ake
the device unable to work or even damage it. For optional front USB cable, please contact your
local dealer.
Pin No.
Definition
Power
1
2
3
4
5
6
7
8
9
10
Power
USBDX-
USBDy-
USBDX+
USBDy+
GND
2
1
10
9
GND
No Pin
NC
16) CLR_CMOS (Clear CMOS)
You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily
shor 1-2 pin. Default doesn't include the "Shunter" to prevent from im proper use this jumper.
1
Open: Normal
1
Short: Clear CMOS
17) BAT(BATTERY)
CAUTION
Dangerofexplosion if batteryisincorrectlyreplaced.
Replace onlywith the same or equivalenttype
recommendedbythemanufacturer.
Dispose ofused batteriesaccording to the
+
manufacturer'sinstructions.
Ifyou wantto erase CMOS...
1. Turn OFF thecomputerand unplugthe powercord.
2. Remove the battery, waitfor 30 second.
3. Re-install the battery.
4. Plug the powercord and turn ON the computer.
8I845PE-RZ Series Motherboard
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 BIOS Setup
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the
basic system configuration. This type of inform ation is stored in battery-backed CMOS RAM so that it
retains the Setup information when the power is turned off.
ENTERING SETUP
Powering ON the com puter and pressing <Del> immediately will allow you to enter Setup. If you require
more advanced BIOS settings, please go to "Advanced BIOS" setting m enu. To enter Advanced BIOS
setting menu, press "Ctrl+F1" key on the BIOS screen.
CONTROL KEYS
<
>< >< ><
>
Move to select item
<Enter>
<Esc>
Select Item
Main M enu - Quit and not save changes into CMOS Status Page Setup Menu
and Option Page Setup Menu - Exit current page and return to Main M enu
Increase the numeric value or make changes
Decrease the num eric value or make changes
General help, only for Status Page Setup Menu and Option Page Setup M enu
Item Help
<+/PgUp>
<-/PgDn>
<F1>
<F2>
<F5>
<F6>
<F7>
Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
Load the file-safe default CM OS value from BIOS default table
Load the Optimized Defaults
<F8>
Q-Flash utility
<F9>
System Inform ation
<F10>
Save all the CMOS changes, only for M ain Menu
MainMenu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible
selections for the highlighted item . To exit the Help Window press <Esc>.
The Main Menu (For example: BIOS Ver. : Fac)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the
screen. The M ain Menu allows you to select from eight setup functions and two exit choices. Use
arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
}
}
}
}
}
}
}
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
higf: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Time, Date, Hard Disk Type...
- 19 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Ifyoucan'tfindthesettingyou want,pleasepress"Ctrl+F1"to searchthe advanced
optionhidden.
•
•
•
•
•
•
•
•
•
StandardCMOS Features
This setup page includes all the item s in standard com patible BIOS.
AdvancedBIOS Features
This setup page includes all the items of Award special enhanced features.
IntegratedPeripherals
This setup page includes all onboard peripherals.
PowerManagementSetup
This setup page includes all the items of Green function features.
PnP/PCI Configuration
This setup page includes all the configurations of PCI & PnP ISA resources.
PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
Frequency/VoltageControl
This setup page is control CPU clock and frequency ratio.
TopPerformance
If you wish to m aximize the perform ance of your system , set "Top Performance" as "Enabled".
LoadFail-Safe Defaults
Fail-Safe Defaults indicates the value of the system param eters which the system would be in safe
configuration.
•
•
LoadOptimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would be in
best performance configuration.
Set Supervisor Password
Change, set, or disable password. It allows you to limit access to the system and Setup, or just
to Setup.
•
•
•
Set User Password
Change, set, or disable password. It allows you to lim it access to the system.
Save & Exit Setup
Save CMOS value settings to CM OS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
8I845PE-RZ Series Motherboard
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Fri, Jan 9 2004
22:31:24
Item Help
Menu Level}
Change the day, month,
year
} IDE Primary Master
} IDE Primary Slave
} IDE Secondary Master
} IDE Secondary Slave
[None]
[None]
[None]
[None]
<Week>
Sun. to Sat.
Drive A
Drive B
Floppy 3 Mode Suport
[1.44M, 3.5"]
[None]
[Disabled]
<Month>
Jan. to Dec.
<Day>
1 to 31 (or maximum
allowed in the month)
Holt On
[All, But Keyboard]
Base Memory
Extended Memory
Total Memory
640K
127M
128M
<Year>
1999 to 2098
higf: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10: Save
F6: Fail-Save Default
ESC: Exit F1: General Help
F7: Optimized Defaults
Date
The date form at is <week>, <m onth>, <day>, <year>.
Week
Month
Day
The week, from Sun to Sat, determ ined by the BIOS and is display only
The month, Jan. Through Dec.
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1999 through 2098
Year
Time
The tim es format in <hour> <minute> <second>. The tim e is calculated base on the 24-hour
military-tim e clock. For example, 1 p.m. is 13:00:00.
IDE Primary Master, Slave / IDE Secondary Master, Slave
The category identifies the types of hard disk from drive C to F that has been installed in the
computer. There are two types: auto type, and manual type. Manual type is user-definable; Auto type
which will automatically detect HDD type.
Note that the specifications of your drive m ust m atch with the drive table. The hard disk will not work
properly if you enter improper information for this category.
Ifyou selectUser Type, related information will be asked to enter to the following items. Enter the information
directly from the keyboard and press <Enter>. Such information should be provided in the documenta-
tion form your hard disk vendor or the system m anufacturer.
Cylinder
Head
Precomp
Number of cylinders
Number of heads
Write precomp
Landing Zone Landing zone
Sector
Number of sectors
If a hard disk has not been installed, select NONE and press <Enter>.
- 21 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the
com puter.
None
No floppy drive installed
360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity.
1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 M ode is Enabled).
720K, 3.5"
3.5 inch double-sided drive; 720K byte capacity
1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity.
2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled
Drive A
Drive B
Both
Normal Floppy Drive. (Default value)
Drive A is 3 mode Floppy Drive.
Drive B is 3 mode Floppy Drive.
Drive A & B are 3 m ode Floppy Drives.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
No Errors
The system boot will not stop for any error that m ay be detected and you
will be prompted.
All Errors
Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
errors. (Default value)
All, But Diskette
The system boot will not stop for a disk error; it will stop for all other errors.
All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all
other errors.
Memory
The category is display-only which is determ ined by POST (Power On Self Test) of the BIOS.
BaseMemory
The POST of the BIOS will determine the amount of base (or conventional) memory installed
in the system.
The value of the base memory is typically 512K for systems with 512K m emory installed on
the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.
ExtendedMemory
The BIOS determines how much extended memory is present during the POST.
This is the am ount of mem ory located above 1 M B in the CPU's memory address map.
8I845PE-RZ Series Motherboard
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Advanced BIOS Features
First Boot Device
Second Boot Device
Third Boot Device
Boot Up Floppy Seek
Password Check
[Floppy]
[HDD-0]
[CDROM]
[Disabled]
[Setup]
[Enabled]
[AGP]
Item Help
Menu Level}
Select Boot Device
priority
#
CPU Hyper-Threading
Init Display First
[Floppy]
Boot from floppy
[LS120]
Boot from LS120
[HDD-0]
Boot from First HDD
[HDD-1]
Boot from Second HDD
higf: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10: Save
F6: Fail-Save Default
ESC: Exit F1: General Help
F7: Optimized Defaults
" # " System will detect automatically and show up when you install the Intel® Pentium®
processor with HT Technology.
4
First / Second / Third Boot Device
Floppy
LS120
HDD-0~3
SCSI
CDROM
ZIP
Select your boot device priority by Floppy.
Select your boot device priority by LS120.
Select your boot device priority by HDD-0~3.
Select your boot device priority by SCSI.
Select your boot device priority by CDROM.
Select your boot device priority by ZIP.
Select your boot device priority by USB-FDD.
Select your boot device priority by USB-ZIP.
USB-FDD
USB-ZIP
USB-CDROM Select your boot device priority by USB-CDROM.
USB-HDD
LAN
Disabled
Select your boot device priority by USB-HDD.
Select your boot device priority by LAN.
Select your boot device priority by Disabled.
Boot Up Floppy Seek
During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360K type is
40 tracks 720K, 1.2M and 1.44M are all 80 tracks.
Enabled
Disabled
BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that
BIOS can not tell from 720K, 1.2M or 1.44M drive type as they are all 80 tracks.
BIOS will not search for the type of floppy disk drive by track number. Note that
there will not be any warning message if the drive installed is 360K. (Default value)
PasswordCheck
System
The system can not boot and can not access to Setup page will be denied if the
correct password is not entered at the prompt.
Setup
The system will boot, but access to Setup will be denied if the correct password
is not entered at the prompt. (Default value)
- 23 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
CPUHyper-Threading
Enabled
Enables CPU Hyper Threading Feature. Please note that this feature is only working
for operating system with multi processors mode supported. (Default value)
Disables CPU Hyper Threading.
Disabled
Init Display First
Select the first initation of m onitor or display from AGP or PCI VGA card.
AGP
Set Init display first to AGP. (Default value)
PCI
Set Init display first to PCI.
Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Integrated Peripherals
On-Chip Primary PCI IDE
On-Chip Secondary PCI IDE
IDE1 Conductor Cable
IDE2 Conductor Cable
USB Controller
[Enabled]
[Enabled]
[Auto]
Item Help
Menu Level}
[Auto]
[Auto]
Auto-detect IDE
cable type
[Enabled]
[Disabled]
[Disabled]
[Auto]
[Enabled]
[Disabled]
[3F8/IRQ4]
[2F8/IRQ3]
[378/IRQ7]
[SPP]
USB Keyboard Support
USB Mouse Support
AC97 Audio
[ATA66/100/133]
Set Conductor cable
to ATA66/100/133(80
-pins)
*
Onboard H/W LAN
Onboard LAN Boot ROM
*
Onboard Serial Port 1
Onboard Serial Port 2
Onboard Parallel Port
Parallel Port Mode
x ECP Mode Use DMA
Game Port Address
Midi Port Address
Midi Port IRQ
[ATA33]
Set Conductor cable
to ATA33(40-pins)
3
[201]
[330]
[10]
higf: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10: Save
F6: Fail-Save Default
ESC: Exit F1: General Help
F7: Optimized Defaults
On-Chip Primary PCI IDE
Enabled
Enable onboard 1st channel IDE port. (Default value)
Disabled
Disable onboard 1st channel IDE port.
On-Chip Secondary PCI IDE
Enabled
Enable onboard 2nd channel IDE port. (Default value)
Disabled
Disable onboard 2nd channel IDE port.
IDE1Conductor Cable
Auto
Will be automatically detected by BIOS. (Default value)
ATA66/100
Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is com patible with ATA66/100).
ATA33
Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
IDE2Conductor Cable
Auto Will be automatically detected by BIOS. (Default value)
ATA66/100
Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is com patible with ATA66/100).
ATA33
Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
"*"For 8I845PE-RZ only.
8I845PE-RZ Series Motherboard
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Controller
Enabled
Disabled
Enable USB controller. (Default value)
Disable USB controller.
USB Keyboard Support
Enabled
Enable USB keyboard support.
Disabled
Disable USB keyboard support. (Default value)
USB Mouse Support
Enabled
Enable USB mouse support.
Disabled
Disable USB mouse support. (Default value)
AC97 Audio
Auto
Disabled
Enable onboard AC'97 audio function. (Default value)
Disable this function.
Onboard H/W LAN *
Enabled
Enable onboard H/W LAN function. (Default value)
Disabled
Disable this function.
Onboard H/W LAN Boot ROM *
This function decide whether to invoke the boot ROM of the onboard LAN chip.
Enabled
Disabled
Enable this function.
Disable this function. (Default Value)
Onboard Serial Port 1
Auto
BIOS will autom atically setup the port 1 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 1 and address is 3F8. (Default value)
Enable onboard Serial port 1 and address is 2F8.
Enable onboard Serial port 1 and address is 3E8.
Enable onboard Serial port 1 and address is 2E8.
Disable onboard Serial port 1.
Onboard Serial Port 2
Auto
BIOS will autom atically setup the port 2 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 2 and address is 3F8.
Enable onboard Serial port 2 and address is 2F8. (Default value)
Enable onboard Serial port 2 and address is 3E8.
Enable onboard Serial port 2 and address is 2E8.
Disable onboard Serial port 2.
Onboard Parallel port
378/IRQ7
278/IRQ5
Disabled
3BC/IRQ7
Enable onboard LPT port and address is 378/IRQ7. (Default value)
Enable onboard LPT port and address is 278/IRQ5.
Disable onboard LPT port.
Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP
Using Parallel port as Standard Parallel Port. (Default value)
EPP
ECP
ECP+EPP
Using Parallel port as Enhanced Parallel Port.
Using Parallel port as Extended Capabilities Port.
Using Parallel port as ECP & EPP mode.
"*"For 8I845PE-RZ only.
- 25 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
ECP Mode Use DMA
3
Set ECP Mode Use DMA to 3. (Default value)
1
Set ECP Mode Use DM A to 1.
Game Port Address
201
Set Game Port Address to 201. (Default value)
209
Disabled
Set Game Port Address to 209.
Disable this function.
Midi Port Address
300
Set Midi Port Address to 300.
330
Disabled
Set Midi Port Address to 330. (Default value)
Disable this function.
Midi Port IRQ
5
Set M idi Port IRQ to 5.
10
Set M idi Port IRQ to 10. (Default value)
Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Power Management Setup
ACPI Suspend Type
Power LED in S1 state
Soft-Off by PWR-BTTN
PME Event Wake Up
[S1(POS)]
[Blinking]
[Instant-Off]
[Enabled]
[Enabled]
[Disabled]
Everyday
Item Help
Menu Level}
[S1]
Set suspend type to
Power On Suspend under
ACPI OS
ModemRingOn
Resume by Alarm
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm
Power On by Mouse
0 : 0 : 0
[Disabled]
[Disabled]
Enter
[S3]
Set suspend type to
Suspend to RAM under
ACPI OS
Power On by Keyboard
x KB Power ON Password
AC Back Function
[Soft-Off]
higf: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10: Save
F6: Fail-Save Default
ESC: Exit F1: General Help
F7: Optimized Defaults
ACPI Suspend Type
S1(POS)
S3(STR)
Set ACPI suspend type to S1. (Default value)
Set ACPI suspend type to S3.
Power LED in S1 state
Blinking
In standby m ode(S1), power LED will blink. (Default value)
Dual/OFF
In standby m ode(S1):
a. If use single color LED, power LED will turn off.
b. If use dual color LED, power LED will turn to another color.
Soft-off by PWR-BTTN
Instant-off
Press power button then Power off instantly. (Default value)
Delay 4 Sec.
Press power button 4 sec to Power off. Enter suspend if button is pressed
less than 4 sec.
8I845PE-RZ Series Motherboard
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PME Event Wake Up
Disabled
Disable this function.
Enabled
Enable PM E as wake up event. (Default value)
ModemRingOn
Disabled
Disable Modem Ring on function.
Enabled
Enable Modem Ring on function. (Default value)
Resumeby Alarm
You can set "Resume by Alarm" item to enabled and key in Date/time to power on system.
Disabled
Enabled
Disable this function. (Default Value)
Enable alarm function to POWER ON system.
If RTC Alarm Lead To Power On is Enabled.
Date (of Month) Alarm :
Time (hh: m m: ss) Alarm :
Everyday, 1~31
(0~23) : (0~59) : (0~59)
Power On By Mouse
Disabled
Disabled this function. (Default value)
Double Click
Double click on PS/2 mouse left button to power on system.
Power On By Keyboard
Password
Enter from 1 to 5 characters to set the keyboard power on password.
Disabled
Disabled this function. (Default value)
Keyboard 98
If your keyboard have "POWER Key" button, you can press the key to
power on your system .
KB Power ON Password
Enter
Input password (from 1 to 5 characters) and press Enter to set the keyboard
power on password.
ACBack Function
Soft-Off
Mem ory
Always in Off state when AC back. (Default value)
System power on depends on the status before AC lost.
Always power on the system when AC back.
Full-On
- 27 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
PnP/PCI Configurations
PCI 1/PCI 5 IRQ Assignment
PCI 2 IRQ Assignment
PCI 3 IRQ Assignment
PCI 4 IRQ Assignment
[Auto]
[Auto]
[Auto]
[Auto]
Item Help
Menu Level}
Device(s) using this
INT:
Display Cntrlr
-Bus 1 Dev 0 Func 0
higf: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10: Save
F6: Fail-Save Default
ESC: Exit F1: General Help
F7: Optimized Defaults
PCI 1/PCI 5 IRQ Assignment
Auto
Auto assign IRQ to PCI 1/PCI 5. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1/PCI 5.
PCI 2 IRQ Assignment
Auto
Auto assign IRQ to PCI 2. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
PCI 3 IRQ Assignment
Auto
Auto assign IRQ to PCI 3. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
PCI 4 IRQ Assignment
Auto
Auto assign IRQ to PCI 4. (Default value)
3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 4.
8I845PE-RZ Series Motherboard
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
PC Health Status
Reset Case Open Status
Case Opened
Vcore
[Disabled]
Yes
1.54V
Item Help
Menu Level}
DDR25V
+3.3V
+12V
2.544V
3.360V
11.92V
41° C
4440 RPM
0 RPM
Don't reset case
open status
Current CPU Temperature
Current CPU FAN Speed
Current SYSTEM FAN Speed
CPU Warning Temperature
CPU FAN Fail Warning
SYSTEM FAN Fail Warning
Clear case open
status at next boot
[Disabled]
[Disabled]
[Disabled]
higf: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10: Save
F6: Fail-Save Default
ESC: Exit F1: General Help
F7: Optimized Defaults
Reset CaseOpen Status
Disabled
Don't reset case open status. (Default value)
Enabled
Clear case open status at next boot.
CaseOpened
If the case is closed, "Case Opened" will show "No".
If the case have been opened, "Case Opened" will show "Yes".
If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and save
CM OS, your computer will restart.
Current Voltage (V) Vcore / DDR25V / +3.3V / +12V
Detect system 's voltage status autom atically.
Current CPUTemperature
Detect CPU temperature autom atically.
Current CPU/SYSTEM FAN Speed (RPM)
Detect CPU/SYSTEM Fan speed status automatically.
CPU Warning Temperature
60oC / 140o F
70oC / 158o F
80oC / 176o F
90oC / 194o F
Disabled
Monitor CPU temperature at 60oC / 140oF.
Monitor CPU temperature at 70oC / 158oF.
Monitor CPU temperature at 80oC / 176oF.
Monitor CPU temperature at 90oC / 194oF.
Disable this function. (Default value)
CPU FAN Fail Warning
Disabled
Fan warning function disable. (Default value)
Enabled
Fan warning function enable.
SYSTEM FAN Fail Warning
Disabled
Fan warning function disable. (Default value)
Enabled
Fan warning function enable.
- 29 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequency/Voltage Control
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Frequency/Voltage Control
CPU Clock Ratio
[15X]
[Disabled]
100
Disabled
[Auto]
266
Item Help
Menu Level}
CPU Host Clock Control
ø CPU Host Frequency(Mhz)
ø Fixed PCI/AGP Frequency
Host/DRAM Clock ratio
Memory Frequency(Mhz)
PCI/AGP Frequency(Mhz)
33/66
higf: Move Enter: Select
F5: Previous Values
+/-/PU/PD: Value F10: Save
F6: Fail-Save Default
ESC: Exit F1: General Help
F7: Optimized Defaults
ø Those items will be available when "CPU Host Clock Control" is set to Enabled.
CPU Clock Ratio
This setup option will automatically assign by CPU detection.
The option will display "Locked" and read only if the CPU ratio is not changeable.
CPU Host Clock Control
Please note that if your system is overclocked and cannot restart, please wait 20secs.
for automatic system restart or clear the CMOS setup data and perform a safe restart.
Disabled
Enabled
Disable CPU Host Clock Control. (Default value)
Enable CPU Host Clock Control.
CPU Host Frequency(MHz)
100M Hz ~ 355MHz
Set CPU Host Clock from 100MHz to 355MHz.
If you use FSB400 Pentium 4 processor, please set "CPU Clock" to 100MHz.If you use FSB533
Pentium 4 processor, please set "CPU Clock" to 133MHz.
Incorrect using it may cause your system broken. For power End-User use only!
Fixed PCI/AGP Frequency
You can choose those mode to adjust PCI/AGP frequency. (Select PCI/AGP frequency
asynchronous with CPU frequency).
8I845PE-RZ Series Motherboard
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Host/DRAM Clock Ratio
(Warning: wrong frequency may m ake system can boot, clear CMOS to overcom e wrong
frequency issue)
for FSB(Front Side Bus) frequency=400MHz,
2.66
Memory Frequency = Host clock X 2.66.
Auto Set M em ory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=533MHz,
2.0 Memory Frequency = Host clock X 2.0.
2.5 Memory Frequency = Host clock X 2.5.
Auto Set M em ory frequency by DRAM SPD data. (Default value)
MemoryFrequency(Mhz)
The values depend on CPU Host Frequency(Mhz).
PCI/AGP Frequency(Mhz)
The values depend on PCI/AGP Divider.
Top Performance
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
}
}
}
}
}
}
}
Standard CMOS Features
Advanced BIOS Features
Integrated Peri
Top Performance
Load Fail-Safe Defaults
efaults
assword
Top Performance
Power Managemen
Disabled.........................[n]
PnP/PCI Configu
ng
Enabled..........................[ ]
PC Health Statu
Frequency/Volta
ESC: Quit
em
hi: Move
ENTER: Accept
F8: Q-Flash
Setup
ESC: Abort
If you wish to m aximize the perform ance of your system , set "Top Performance" as "Enabled".
Disabled Disable this function. (Default Value)
Enabled Enable Top Performance function.
"Top Performance" will increase H/W working speed. Different system configuration (both H/W
com ponent and OS) will effect the result. For exam ple, the sam e H/W configuration might not run
properly with Windows XP, but works sm oothly with Windows NT. Therefore, if your system is not
perform enough, the reliability or stability problem will appear sometimes, and we will recomm end you
disabling the option to avoid the problem as mentioned above.
- 31 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
}
}
}
}
}
}
}
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
PnP/PCI Load Fail-Safe Defaults(Y/N)?N
PC Health Status
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
higf: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Fail-Safe Defaults
Fail-Safe defaults contain the most appropriate values of the system parameters that allow minim um
system performance.
Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
}
}
}
}
}
}
}
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
PnP/PCI Load Optimized Defaults(Y/N)?N
PC Health Status
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
higf: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Optimized Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the system autom atically
detects.
8I845PE-RZ Series Motherboard
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
}
}
}
}
}
}
}
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Enter Password:
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
higf: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Change/Set/Disable Password
When you select this function, the following message will appear at the center ofthe screen to assist you
in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password.
Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not
enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A m essage
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS
Setup program function. When enabled, the Supervisor password is required for entering the BIOS
Setup program and having full configuration fields, the User password is required to access only basic
items.
If you select "System " at "Password Check" in Advance BIOS Features Menu, you will be prom pted
for the password every time the system is rebooted or any tim e you try to enter Setup M enu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only
when you try to enter Setup.
- 33 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
}
}
}
}
}
}
}
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Save to CMOS and EXIT(Y/N)?Y
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
higf: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Save Data to CMOS
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
}
}
}
}
}
}
}
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Quit Without Saving (Y/N)?N
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
higf: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Abandon all Data
Type "Y" will quit the Setup Utility without saving to RTC CM OS.
Type "N" will return to Setup Utility.
8I845PE-RZ Series Motherboard
- 34 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Install Drivers
Install Drivers
Pictures below are shown in Windows XP
Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM
device icon in "My computer", and execute the setup.exe.
INSTALL CHIPSET DRIVER
This page shows the drivers that need to be installed for the system. Click each item to install the driver
manually or switch to the
to install the drivers automatically.
The "Xpress Install" uses the"Click and Go" technology to install the drivers automatically. Just select the
drivers you want then click the "GO" button. The will execute the installation for you by itself.
We recommend that you install all components in the list.
Massage: Some device drivers will restart your
system automatically. After restarting your system the
"Xpress Install" will continue to install other drivers.
Click "GO".
- 35 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver Installation
Driver install finished!! you have to reboot system!!
Item Description
n
n
n
n
n
n
Intel Chipset Software Installation Utility
Tell the operating system how the chipset components will be configured.
Intel Application Accelerator
Designed to improve performance of the storage sub-system and overall system performance.
USB Pacth for WinXP
This patch driver can help you to resolve the USB device wake up S3 hang up issue in XP.
RealTek LAN Driver *
RealTek 10/100 LAN driver for 81xx series chips.
C-Media AC97 Audio Driver
Install C-Media AC97 audio driver.
Intel/NEC USB 2.0 Driver
It is recommended that you use the Microsoft Windows update for the most updated driver
for XP/2K.
"*" For 8I845PE-RZ only.
8I845PE-RZ Series Motherboard
- 36 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 37 -
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
8I845PE-RZ Series Motherboard
- 38 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 39 -
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTACT US
Contact us via the information in this page all over the world.
—
Taiwan
—
The Netherlands
Gigabyte Technology Co., Ltd.
Giga-Byte Technology B.V.
Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien,
Taiwan, R.O.C.
Address: Verdunplein 8 5627 SZ, Eindhoven, The Netherlands
Tel: +31 40 290 2088
Tel: 886 (2) 8912-4888
Fax: 886 (2) 8912-4004
Tech. Support:
NL Tech.Support : 0900-GIGABYTE (0900-44422983, 0.2/M)
BE Tech.Support : 0900-84034 ( 0.4/M)
Fax: +31 40 290 2089
Non-Tech. Support (Sales/Marketing issues):
Tech. Support:
Non-Tech. Support (Sales/Marketing issues):
—
USA
G.B.T. INC.
—
China
Address: 17358 Railroad St, City of Industry, CA 91748.
Tel: 1 (626) 854-9338
NINGBO G.B.T. Tech. Trading CO., Ltd.
Tech. Support:
Fax: 1 (626) 854-9339
Tech. Support:
Non-Tech. Support (Sales/Marketing issues):
Non-Tech. Support (Sales/Marketing issues):
Beijing
Tel: 86-10-82856054, 86-10-82856064, 86-10-82856094
Fax: 86-10-82856575
—
Germany
G.B.T. Technology Trading GmbH
Tel: 49-40-2533040
Chengdu
Tel: 86-28-85236930
49-01803-428468 (Tech.)
Fax: 86-28-85256822
Fax: 49-40-25492343 (Sales)
49-01803-428329 (Tech.)
GuangZhou
Tel: 86-20-87586273
Tech. Support:
Fax: 86-20-87544306
Non-Tech. Support (Sales/Marketing issues):
Shanghai
Tel: 86-21-64737410
Fax: 86-21-64453227
Shenyang
—
Japan
Tel: 86-24-23960918, 86-24-23960893
Wuhan
Nippon Giga-Byte Corporation
Tel: 86-27-87854385, 86-27-87854802
Fax: 86-27-87854031
Xian
Tel: 86-29-5531943
Fax: 86-29-5539821
—
U.K
G.B.T. TECH. CO. LTD.
Tel: 44-1908-362700
Fax: 44-1908-362709
Tech. Support:
Non-Tech. Support (Sales/Marketing issues):
8I845PE-RZ Series Motherboard
- 40 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|