OPERATOR’S MANUAL
SB30X-XXX-X
RELEASED:
REVISED:
(REV. G)
2-18-00
5-27-10
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
3" SHOCK BLOCKER®
METALLIC PULSATION DAMPENER
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to the Model Description Chart to match the pump material
options.
637330-3X for repair of the diaphragms and “O”rings (see page 4).
PUMP DATA
Models. . . . . . . . . . . . . . . . . see Model Description Chart for “-XXX-X”
Pulsation Dampener Type . . . . . . . . . . . . . Metallic
Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Model Description Chart
Weight . . . . SB30X-XAX-X . . . . . . . . . . . . . . 41 lbs (18.6 kgs)
SB30X-XCX-X . . . . . . . . . . . . . . 94 lbs (42.6 kgs)
SB30X-XSX-X. . . . . . . . . . . . . . . 96 lbs (43.5 kgs)
Material Inlet / Outlet
SB30X-AXX-X . . . . . . . . . . . . . . 3 - 8 N.P.T.F. - 1
SB30X-BXX-X . . . . . . . . . . . . . . Rp 3 (3 - 11 BSP parallel)
Air Inlet (female) . . . . . . . . . . . . . . . . . . . . . . . 3/4 - 14 N.P.T.
Maximum Air Inlet Pressure . . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure. . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Temperature Limits (diaphragm / seal material)
E.P.R. / EPDM . . . . . . . . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)
Nitrile . . . . . . . . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)
Santoprene® . . . . . . . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)
PTFE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)
Viton®. . . . . . . . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)
Maximum Fluid Volume . . . . . . . . . . . . . . . 367 in.3 (6.01 lit.)
Dimensional Data. . . . . . . . . . . . . . . . . . . . . . see page 7
Figure 1
MODEL DESCRIPTION CHART
SB30 X - X X X - X
Air Section Material
A - Aluminum
S - Stainless Steel
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or
the factory if you have questions concerning availability.
Fluid Connection
A - 3 - 8 N.P.T.F. - 1
B - Rp 3 (3 - 11 BSP, parallel)
Fluid Cap Material
A - Aluminum
C - Cast Iron
S - Stainless Steel
Hardware Material
P - Carbon Steel
S - Stainless Steel
Diaphragm Material
A - Santoprene
G - Nitrile
T - PTFE / Santoprene
V - Viton
Fluid Section Service Kit Selection
SB30X - XXX - X
637330 - 3 X
Diaphragm
EXAMPLE: Model #SB30A-BAP-G
Fluid Section Service Kit # 637330-3G
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX(800) 892-6276
CCN 99828618
© 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL DESCRIPTION
FLUID SECTION DISASSEMBLY
1. Remove (107) reducing bushing.
2. Remove six (26) screws, releasing two (4) flanges and (11) “O”
rings.
3. Remove eight (27) screws and (29) nuts, releasing (15) fluid cap.
4. Secure (14) screw in a vise, with (101) air valve body upward.
5. Using a 15/16” socket on (186) screw, unthread and remove
(186) screw and (10) washer.
6. Remove (68) air cap from (7) diaphragm and components.
7. Remove (14) screw from the vise. Unthread and remove (1) rod,
releasing (2) stopper, (5) back-up washer, (196) cushion, (7) or (7
and 8) diaphragms, (6) washer, (3) “O” ring and (9) washer from
(14) screw.
8. Remove four (131) screws, releasing (101) air valve body from
the (68) air cap.
The ARO® shock blocker pulsation dampener is designed to work
with 1:1 ratio pumps having an outlet pressure not exceeding 120
p.s.i. (8.3 bar). The shock blocker will effectively reduce material
pressure variations, surges and shock to piping and delivery in fluid
systems during pump reversal. It can significantly contribute to
pulse reduction in low pressure spray applications.
Accurate selection of wetted material will assure longest service life
and minimize down time. Several material options are available for
the body and diaphragm materials. Fluid section materials avail-
able include: aluminum, cast iron and stainless steel. For specific
fluid compatibility, consult the chemical manufacturer.
The shock blocker uses a single air pressurized, flexible diaphragm
working against the fluid line pressure. Several diaphragm material
options are available to allow custom matching to the fluid mate-
rial for best compatibility (refer to the model description chart).
Shock blocker units can also be added in series to provide addi-
tional dampening on the material.
9. Remove (144) “U”cup from (68) air cap.
10. Remove (103) sleeve from (101) air valve body.
Pressure relief through the exhaust port is a normal compensating
function of the control valve in the shock blocker. It will automati-
cally adjust itself to the required operating pressure once the mate-
rial pressure has been applied. The pressure supplied to the shock
blocker needs to be equal to the material pressure to provide the
proper dampening effect.
FLUID SECTION REASSEMBLY
Clean and inspect all parts. Replace worn or damaged parts
with new parts as required. Lubricate all replacement parts and
metallic moving parts with Lubriplate® FML-2 grease upon re-
assembly.
y
1. Grease and assemble two (172) “O”rings to (103) sleeve.
2. Assemble (103) sleeve into the (101) air valve body.
3. Grease and assemble (70 and 173) “O” rings to (101) air valve
body.
AIR AND LUBE REQUIREMENTS
EXCESSIVE AIR PRESSURE. Can cause pulsation
WARNING
dampener damage, personal injury or property damage.
A filter capable of filtering out particles larger than 50 microns
should be used on the air supply. There is no lubrication re-
quired other than the “O” ring lubricant which is applied during
assembly or repair.
If lubricated air is present, make sure that it is compatible with
the “O”rings and seals in the air motor section of the pump.
4. Grease and assemble (144) “U”cup into (68) air cap.
5. Assemble (101) air valve body to (68) air cap.
6. Assemble four (131) screws, securing (68) air cap. NOTE: Tighten
(131) screws to 20 - 30 ft lbs (27.1 - 40.7 Nm).
7. Assemble (9) washer, (3) “O” ring, (6) washer, (7) or (7 and 8)
diaphragms, (196) cushion, (5) back-up washer and (2) stopper
to (14) screw. NOTE: For models with PTFE diaphragms: Item
(8) Santoprene diaphragm is installed with the side marked
“AIR SIDE” towards the pump center body. Install the PTFE dia-
phragm (7) with the side marked “FLUID SIDE” towards the (15)
fluid cap.
8. Assemble (1) rod to (14) screw.
9. Grease and assemble two (173) “O”rings to (1) rod.
10. Place this assembly into (68) air cap.
11. Assemble (10) washer and (186) screw into (101) air valve body
and thread into (1) rod. Clamp (14) screw in a vise, with (186)
screw upward, and tighten (186) screw to 65 - 70 ft lbs (88.1 -
94.9 Nm).
12. Remove assembly from the vise and assemble to (15) fluid cap,
securing with eight (27) screws and (29) nuts. NOTE: Tighten (27)
screws to 60 - 70 ft lbs (81.3 - 94.9 Nm).
y
y
OPERATION
DO NOT EXCEED 120 P.S.I. (8.3 BAR). Operating
CAUTION
at higher pressure can cause explosion, resulting in property
damage or severe injury.
Pressure relief through the exhaust port is a normal compen-
sating function of the control valve in the shock blocker. It will
automatically adjust itself to the required operating pressure
once the material pressure has been applied.
Operate the system for a few minutes to equalize air and fluid
chambers of the pulsation dampener.
y
y
PARTS AND SERVICE KITS
Refer to the part views and descriptions as provided on pages 4
and 5 for parts identification and Service Kit information.
13. Grease and assemble two (11) “O”rings to two (4) flanges.
14. Assemble two (4) flanges to (15) fluid cap, securing with six (26)
screws. NOTE: Tighten (26) screws to 60 - 70 ft lbs (81.3 - 94.9
Nm).
15. Apply Lubriplate FML-2 grease to threads of (101) air valve
body. Apply PTFE tape to threads of (107) reducing bushing
and assemble to (101) air valve body.
Certain ARO “Smart Parts” are indicated which should be avail-
able for fast repair and reduction of down time.
y
y
MAINTENANCE
Provide a clean work surface to protect sensitive internal mov-
ing parts from contamination from dirt and foreign matter dur-
ing service disassembly and reassembly.
Keep good records of service activity and include pump in pre-
ventive maintenance program.
Before disassembling, empty captured material in the fluid cap
by tipping the pulsation dampener on end.
y
y
Viton® is registered trademarks of the DuPont Company Santoprene® is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P.
y
y
y
Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) ARO® and Shock Blocker® are registered trademarks of Ingersoll-Rand Company
y
y
y
SB30X-XXX-X (en)
Page 3 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / SB30X-XXX-X
Indicates parts included in 637330-3X service kit. Service kit also includes 94276 Lubriplate FML-2 grease packet.
DIAPHRAGM OPTIONS SB30X-XXX-X
SB30X-XXX-A
Qty Part No. [Mtl] Part No.
637330-3A 637330-3G
SB30X-XXX-G
[Mtl] Part No.
637330-3T
SB30X-XXX-T
[Mtl] Part No.
637330-3V
SB30X-XXX-V
(size)
Item Description
[Mtl]
Service Kit
Diaphragm
Diaphragm
7
8
(1) 94091-A
(1) - - - - -
[Sp] 94091-G
- - - - - - - -
[B] 94090-T
- - - 94110-A
[B] Y328-248
[T] 95345
[Sp] - - - - -
[V]
- - -
[V]
(1/8" x 5" o.d.)
11 "O" Ring
(2) 95187
[E] Y325-248
[T] Y327-248
AIR SECTION PART OPTIONS SB30X-XXX-X
Aluminum
SB30A-XXX-X
Qty Part No. [Mtl] Part No.
Stainless Steel
SB30S-XXX-X
(size)
Item Description
[Mtl]
[SS]
[SS]
[SS]
[SS]
[SS]
5
Back-up Washer
(1) 94831-1
(1) 94030-3
(1) 94839
[C] 94831-2
[A] 94031-4
[A] 94843
68 Air Cap
101 Air Valve Body
107 Reducing Bushing
(1-1/2 - 11-1/2 N.P.T. male x 3/4 - 14 N.P.T. female)
(1) Y45-22-C
(2) - - - - -
[I]
Y45-322-T
(5/32" o.d. x 3/4" long)
181 Roll Pin
- - - Y178-56-S
MATERIAL CODE
FLUID CAP MATERIAL OPTIONS SB30X-XXX-X
[A]
=
=
=
=
=
=
=
=
=
=
=
=
=
=
Aluminum
Nitrile
Aluminum
Cast Iron
Stainless Steel
SB30X-XSX-X
[B]
[Br]
[Bz]
[C]
[CI]
[Co]
[D]
[E]
Brass
Bronze
Carbon Steel
Cast Iron
Copper
Acetal
SB30X-XAX-X
SB30X-XCX-X
(size)
Item Description
Qty Part No.
[Mtl] Part No.
[Mtl] Part No.
[Mtl]
[SS]
[SS]
[SS]
(N.P.T.F.)
Flange
(2) 94846
(2) 94846-1
(1) 94024
[A] 94847
[A] 94847-1
[A] 94106
[CI] 94940
[CI] 94940-1
[CI] 94107
4
(BSP)
E.P.R.
[I]
Iron
Santoprene
Stainless Steel
PTFE
15 Fluid Cap
[Sp]
[SS]
[T]
[V]
Viton
EXTERNAL HARDWARE OPTIONS SB30X-XXX-X
Carbon Steel
Stainless Steel
SB30X-XXP-X
SB30X-XXS-X
(size)
Item Description
Qty Part No.
[Mtl] Part No.
[C] 94412-2
[C] 94991
[C] 95053
[Mtl]
[SS]
[SS]
[SS]
(M12 x 1.75 - 6g x 45 mm)
26 Screw
27 Screw
(6) 94412-1
(8) 94991-1
(8) 95053-1
(M12 x 1.75 - 6g x 60 mm)
(M12 x 1.75 - 6h)
29 Nut
COMMON PARTS
(size)
(size)
Item Description
Qty Part No.
[Mtl]
[C]
Item Description
Qty Part No.
(4) Y325-111
(1) 94836
[Mtl]
[B]
(3/32” x 5/8” o.d.)
1
2
3
6
9
Rod
(1) 94941
70 “O” Ring
103 Sleeve
Stopper
“O” Ring
Washer
(1) 94837
[D]
[Bz]
[C]
(1/8” x 1” o.d.)
(M10 x 1.5 - 6g x 30 mm)
(1) Y328-210
(1) 94942
[T]
131 Screw
(4) 94845
(3/16” x 1-3/8” o.d.)
[SS]
[SS]
[SS]
[SS]
[C]
144 “U” Cup
172 “O” Ring
173 “O” Ring
(1) Y186-51
(2) Y325-24
(3) Y330-117
(1) Y5-105-C
(1) 94631
[B]
(13/16” i.d. x 2” o.d.)
(1/16” x 1-1/4” o.d.)
(3/32” x 1” o.d.)
Washer
(1) Y13-12-T
(1) 93065
[B]
(0.630” i.d. x 1.687” o.d.)
10 Washer
[B]
(3/4” - 16 x 2-1/2”)
(5/8” - 18 x 1”)
14 Screw
(1) Y5-131-T
(1) Y254-178-Z
(1) 93004
186 Screw
[C]
(1/4” - 20 x 1/2”)
19 Screw, Self-Tapping
43 Ground Lug
196 Cushion
201 Muffler
[Sp]
[Br]
[Co]
(1) 20312-1
Page 4 of 8
SB30X-XXX-X (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / SB30X-XXX-X
ASSEMBLY TORQUE REQUIREMENTS
)
(
NOTE: DO NOT OVERTIGHTEN FASTENERS.
107
186
(14) screw, 65 - 70 ft lbs (88.1 - 94.9 Nm).
(26) screws, 60 - 70 ft lbs (81.3 - 94.9 Nm).
(27) screws, 60 - 70 ft lbs (81.3 - 94.9 Nm).
(131) screws, 20 - 30 ft lbs (27.1 - 40.7 Nm).
10
Apply Lubriplate FML-2 grease
LUBRICATION / SEALANTS
101
19
Apply Lubriplate FML-2 grease (94276) to all “O” rings, “U”
cups and mating parts.
c
d
Apply anti-seize compound to threads and bolt and nut
flange heads which contact pump case when using stain-
less steel fasteners.
43
201
NOTE: Lubriplate FML-2 is a white food grade petroleum grease.
c
173
3
1
c
c
172
70
c
144
103
5
7
8
6
181
d
29
68
2
4
131
173
)
Torque Sequence
c
View for SB30X-XXX-T (PTFE diaphragm) configuration only.
1
2
8
Santoprene
5
7
PTFE
196
7
6
COLOR CODE
Diaphragm
Color
Material
Nitrile
Black
Tan
Santoprene
c
3
Santoprene (back-up) Green
PTFE
Viton
White
Yellow (-)
9
(-) Dash
14
11
)
d
c
d
26
4
26
)
(
d
(
c
15
27
11
4
Figure 3
SB30X-XXX-X (en)
Page 5 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPICAL CROSS SECTION
Figure 4
TROUBLE SHOOTING
No dampening effect or erratic performance.
Air bubbles in product discharge.
y
y
Check for diaphragm rupture.
Check connections of the pump’s suction plumbing.
Check tightness of (14) diaphragm screw.
y
y
y
Check for blocked or restricted outlet hoses.
Check the air supply. Make certain the air pressure to the shock
blocker is equal to the fluid pressure.
Fluid leakage:
- from exhaust port.
Check for diaphragm rupture.
Constant air leakage:
- from exhaust port.
y
- from flange.
Check for damaged (172 and 173) “O”rings.
Check for damaged (11) “O”ring.
y
y
y
- from air cap.
Check the tightness of (26) screws.
Check the tightness of (27) screws.
- from fluid cap.
y
Check air pressure to the valve block (relieve fluid pressure).
Check the tightness of (27) screws.
Check for cracks. Discontinue use.
y
y
y
Page 6 of 8
SB30X-XXX-X (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONAL DATA
Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
3/4 - 14 N.P.T. Air inlet
15”
(381 mm)
10-7/8”(276 mm)
20-5/8”(524 mm)
3 - 8 N.P.T.F. - 1 or
Rp 3 (3 - 11 BSP parallel)
15”
(381 mm)
Figure 5
SB30X-XXX-X (en)
Page 7 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
PN 97999-867
Page 8 of 8
SB30X-XXX-X (en)
Download from Www.Somanuals.com. All Manuals Search And Download.
|