TSS-4000
TOTAL SPEAKER SOLUTIONS
TSS-CENTER4000
Owner’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Tilting the Speaker
Wall-Mounting the TSS-CENTER4000 Using the
If needed, the enclosed stand allows you to tilt the speaker
across a wide range (i.e., up a maximum of 18˚ or down a
maximum of 7˚), as shown in Figure 3.
Included Wall Bracket
The customer is responsible for proper selection and use of
mounting hardware, and for correctly and safely wall-mounting
the speakers.
Important!
Do not exceed the tilt range. Doing so may cause the speaker to
fall out of its stand.
Step One
Remove the wall bracket cover by removing the four wall bracket
screws on the ends as shown.
Step Two
Run the speaker wire behind the wall bracket and out the hole
in the center. After deciding where to place the center speaker,
attach the wall bracket (in a horizontal position) to the wall
using the appropriate screws and anchors.
Center Hole
Figure 3.
Wall Bracket
Mounting Screws and Anchors
Not Included
Step Three
Run the speaker wires out through the hole in the center of
the wall bracket cover. Resecure in place with the four wall
bracket screws, as shown.
3
TSS-CENTER4000
Download from Www.Somanuals.com. All Manuals Search And Download.
Step Six
Step Four
The wall-bracket design allows for rotation of the speakers
at angles up to 30 degrees of center. Position the speakers
so they face toward the primary listening position, before
fully tightening.
Using the included Allen wrench, remove the top and bottom
end caps of the speaker by unscrewing the single center screw
on bottom.
End Cap
End Cap
1/4-20 x 3/4"
Screw
Step Five
Connect the wires (page 5). Replace the end caps while
capturing the wall bracket between parts A and B of the
end cap, securing it in place.
Wall-Mount
End Cap B
Wall-Mount
End Cap A
4
TSS-CENTER4000
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING THE SPEAKER
CARE OF YOUR SPEAKER SYSTEM
After placing the speaker, you are ready to connect it to your
system. First, turn off all audio system power. Use high-quality
speaker wire to make the connections. Consult the owner’s
manuals included with your amplifier or receiver for connection
and operation procedures.
When needed, use a soft cloth to remove any fingerprints or
to wipe off dust. Do not use any cleaning products or polish.
Clean the grille by gentle vacuuming.
Surround Modes
When using the TSS-CENTER4000 in a Dolby* Digital or DTS®
home theater system, make sure the receiver’s/processor’s
center channel speaker modes are set to“Small.”
Wiring and Polarity
The TSS-CENTER4000 speaker has gold-plated terminals that
can accept bare wire.To ensure proper polarity, connect each
+ terminal on the back of the amplifier or receiver to the
respective + (red) terminal on each speaker, as shown in
Figure 4. Connect the – (black) terminals in a similar way.
See the owner’s manuals that were included with your
amplifier or receiver to confirm connection procedures.
Important!
Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will degrade the imaging and bass
response of the home theater system.
After correctly placing and wiring the TSS-CENTER4000 and
the rest of your speaker system, adjust the levels for all of the
channels as recommended by the manufacturer of your
receiver/processor.
ᕡ
ᕢ
–
+
Figure 4.This example shows how to connect bare wires to the
terminals. Banana plugs may also be inserted directly into the
rear of the connector.
ᕡ Loosen the terminals.
ᕢ Insert bare ends; tighten terminals.
5
TSS-CENTER4000
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TSS-CENTER4000
Frequency Response
120 – 20kHz ( 3dB)
8 ohms
Nominal Impedance
Sensitivity
89dB
(2.83V @ 1m)
Recommended Amplifier
Power Range
10 – 150 watts
Crossover Frequencies
Low Frequency Drivers
1,000Hz, 3,800Hz; 24dB/octave
(4) 3-1/2" (89mm) MMD®,
magnetically shielded
Mid Frequency Drivers
High Frequency Driver
(2) 3-1/2" (89mm) MMD,
magnetically shielded
3/4" (19mm) MMD,
elliptical waveguide,
magnetically shielded
Dimensions (H x W x D)
Weight
4-1/8" x 23" x 4-3/8"
(105mm x 584mm x 111mm)
12.7 lb (5.8kg)
Infinity continually strives to update and improve existing products, as well as create new ones.
The specifications and construction details in this and related Infinity publications are therefore
subject to change without notice.
Declaration of Conformity
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the product
described in this owner’s manual is in compliance
with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Robin Marshall
Harman Consumer International
Chateau-du-Loir, France 10/04
6
TSS-CENTER4000
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2004 Harman International Industries, Incorporated
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (USA only) www.infinitysystems.com
*Trademarks of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. Infinity and MMD are registered trademarks,
and Total Solutions is a trademark, of Harman International Industries, Incorporated.
Part No. 400-OMCNTR 10/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|