Operating instructions
DISHWASHER
Contents
EN
Installation, 2-3-4
Positioning and levelling
English,1
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Electrical connection
Description of the appliance, 5
Overall view
Control panel
Loading the racks, 6
Lower rack
Cutlery basket
Upper rack
Start-up and use, 7-8
Starting the dishwasher
Measuring out the detergent
Wash options
IDP 148
Wash cycles, 9
Table of wash cycles
Rinse aid and refined salt, 10
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 11
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 12
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the water outlet hose
Anti-condensation strip*
EN
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 4 cm. Alternatively, rest it over a
sink or tub; the free end of the hose should not remain
immersed in water.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt dispenser
with water and add only then approximately 1 kg of salt (see
chapter entitled Rinse aid and refined salt). The water may
overflow: this is normal and is not a cause for concern. Select
the water hardness value (see chapter entitled Rinse aid and
refined salt). - After the salt has been poured into the
machine, the LOW SALT indicator light* switches off.
The special plastic elbow*
A
makes it easier to find the best
layout: fix the elbow to the wall
securely in order to prevent the
outlet hose from moving and
spilling the dirty water.
The part of the hose marked
with the letter A should be
between 40 and 100 cm above
the ground (see figure).
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
We advise against the use of hose extensions.
Electrical connection
Technical data
Before inserting the plug into the electrical socket, make sure
that:
width 60 cm
height 85 cm
depth 60 cm
Dimensions
• The socket is earthed and complies with current
regulations.
Capacity
14 standard place-settings
• The socket can withstand the maximum load of the
appliance, which is indicated on the data plate located on
the inside of the door (see chapter entitled Description of
the appliance).
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply
voltage
See appliance data plate
See appliance data plate
See appliance data plate
• The power supply voltage falls within the values indicated
on the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance. If
this is not the case, ask an authorised technician to replace
the plug (see Assistance); do not use extension cables or
multiple sockets.
Total absorbed
power
Fuse
This dishwasher conforms to
the following European
Community Directives:
-2006/95/CE dated 16/01/2007
(Low Voltage) and subsequent
modifications
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
-2002/96/ CE Waste Electrical
and Electronic Equipment
(WEEE)
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
to prevent all potential hazards. (See Assistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
* Only available in selected models.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
As the colours of the wires in the mains lead may not
Electrical Connection
EN
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or
coloured Red.
If your appliance is supplied with a 13 amp. fused plug
it can be plugged into a 13 amp socket for immediate
use. Before using the appliance please read the
instruction below.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
Connect Blue wire to terminal marked “N” or coloured
Black.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
If a 13 amp plug (BS 1363) is used it must be fitted with
a 13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used, and
the fuse cover re-fitted. If the fuse cover is lost, the
plug must not be used until a replacement is obtained.
If you are in any doubt about the electrical supply to
your machine, consult a qualified electrician before
use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colours as indicated by the coloured marking
or the colour that is embossed in words on the base of
the plug. Replacements can be obtained directly from
your nearest Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
“NEUTRAL” (“N”)
“LIVE” (“L”)
Removing the plug:
BROWN
Ifyour appliance has a non-rewireable moulded plug
and you should wish to remove it to re-route the mains
cable through partitions, units etc., please esure that
either:
GREEN AND YELLOW “EARTH” (“E”) or
- the plug is replaced by a fused 13 amp re-wireable
plug
- or:
bearing the BSI mark of approval
- the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instruction for connecting cable to an altenative
plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Disposing of the appliance:
Green & Yellow
Blue
- Earth
- Neutral
- Live
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible to
the plug body and dispose of it as described above.
Brown
CAUTION:
- Once the appliance has been installed, the electrical plug
and socket should remain accessible.
- The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the
appliance
Overall view
EN
1.
Upper rack
2.
Upper sprayer arm
Tip-up compartments
Rack height adjuster
Lower rack
3.
4.
5.
6.
Lower sprayer arm
Cutlery basket
7.
8.
Washing filter
9.
Salt dispenser
10.
11.
12.
Detergent and rinse aid dispensers
Data plate
Control Panel***
Control panel
Select wash
cycle button
Display
Start/Pause button
and indicator light
ON/OFF/RESET
button
Half load
button
Delayed start
button
Multi-functional
Tablets button
Washing
indicator light
Drying
indicator light
Low Rinse aid
indicator light*
Time remaining
light-up display
Wash cycle number
light-up indicator
Delayed start
indicator light
Multi-functional tablets
indicator light
Low Salt
indicator light*
Half load
indicator light
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the racks
Before loading the racks, remove all food residues from the
crockery and empty liquids from glasses and cups.
After loading the appliance, check that the sprayer arms
can rotate freely.
Tip-up compartments with adjustable tilt
- The tilt feature can be used to increase the space in the upper
rack, to position wine glasses with different stem lengths safely
and to improve drying performance.
EN
Tilt A
Tilt B
Tilt C
Lower rack
The lower rack can hold pans, lids, plates, salad bowls, cutlery,
etc. as seen in the Loading examples.
Plates and large covers should be placed at the sides of the
rack, ensuring that they do not block the rotation of the upper
sprayer arm.
Some dishwasher
- Lift the tip-up compartment, slide it gently and position it in the
desired tilt angle.
models are fitted
with tip-up
sections*, which
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower level.
can be used in a
vertical position when arranging plates or in a horizontal position
when arranging pans and salad bowls.
The height of the upper rack should ideally be adjusted
WHEN THE RACK IS EMPTY.
Cutlery basket
The type of cutlery basket may vary according to the
dishwasher model: it may be modular, non-modular or a sliding
version. The non-modular basket must only be positioned at
the front of the lower rack.
Never lift or lower the rack on one side only.
Open the left and right guide rail stops and
pull out the rack; position it higher or lower
as required, slide it along the guide rails
until the front wheels are in place and close
the stops (see figure).
The modular basket
may be separated into
two parts, a solution
which is recommended
If the rack is fitted with “Dual Space”
handles*(see figure), pull out the upper
rack until it reaches its stop point, grip the
handles at the sides of the rack and move it
upwards or downwards, then slowly let it fall
back into place.
when performing a half
load wash (only in models offering this option), is available in a
sliding version (positioned at any point on the lower rack by
sliding it between the fixed or tip-up inserts.
- Both versions are fitted with a collapsible sliding system which
means the cutlery can be arranged in the best possible way.
Knives and other utensils with sharp edges must be placed in
the cutlery basket with the points facing downwards, or they
must be positioned horizontally in the tip-up compartments on
the upper rack.
Loading examples for the upper/lower rack
Cutlery basket positioning examples
Items which should not be washed in the dishwasher
• Wooden items, objects with wooden or horn handles or glued-
on parts.
• Items made from aluminium, copper, brass, pewter or tin.
• Items made from plastic material which is not heat-resistant.
• Antique or hand-painted porcelain.
Upper rack
Load this rack with delicate and lightweight crockery: glasses,
tea and coffee cups, saucers, small salad bowls, saucepans
and small saucepans which are not too soiled, using the
Loading examples as a guide.
• Antique silver. Silver which is not antique may, however, be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other metals.
• Mugs and cups, long sharp knives and serving utensils:
place these on the tip-up compartments**.
We recommend the use of crockery which is dishwasher safe.
*Only available in selected models.
** The number and position may vary.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up and use
Starting the dishwasher
Measuring out the detergent
EN
A good wash result also depends on the correct
amount of detergent being used; exceeding the stated
amount does not result in a more effective wash and
increases environmental pollution.
1. Turn the water tap on.
2. Press the ON/OFF button: all the indicator lights on
the control panel will light up for a few seconds.
3. Open the door and pour in a suitable amount of
detergent (see below).
Only use detergent which has been
4. Load the racks (see Loading the racks) and shut the
door.
specifically designed for dishwashers.
DO NOT USE washing up liquid.
5. Select the wash cycle in accordance with the type
of crockery and its soil level (see Table of wash
cycles) by pressing the P button.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle
has ended.
6. Select the wash options* (see adjacent
information).
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
7. Start the cycle by pressing the Start/Pause button
(fixed light). A long beep signals the start of the wash
cycle; the wash cycle indicator light is illuminated and
the time remaining until the end of the cycle is
displayed.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid liquid
and salt should be used.
8. Two short beeps and one long one indicate the end
of the wash cycle; the Start/Pause button switches off
and the word END appears on the display. Switch off
the appliance by pressing the ON/OFF button, shut off
the water valve and unplug the appliance from the
electricity socket.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
D
1. Open cover C by pressing
button D.
A
B
9. Wait for a few minutes before removing the
crockery, in order to avoid burns. Unload the racks,
beginning with the lower level.
2. Pour in the detergent after
consulting the Table of wash
cycles:
• For powder detergent use
compartments A and B.
• For detergent in tablet form:
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that
it has only just begun: once the wash cycle has started,
switch off the machine by pressing and holding the ON/
OFF/Reset button. Switch it back on using the same
button and select the desired wash cycle and options.
C
when the cycle requires 1 tablet, place it in compartment
A and close the cover; when it requires 2, place the
second tablet at the bottom of the appliance.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
Adding extra crockery
Press the Start/Pause button (the corresponding
indicator light will flash). Open the door, taking care to
avoid the escaping steam, and place the crockery inside
the appliance. Press the Start/Pause button (fixed light):
the cycle starts from the point at which it was interrupted.
If the Start/Pause button is pressed so as to pause the
machine, the wash cycle or the Delayed Start* function
(if selected) is interrupted.
At this stage it is not possible to change the wash cycle.
Accidental interruptions
If the door is opened during the wash cycle, or if there is
a power cut, the cycle stops. It starts again from the point
at which it was interrupted once the door has been shut
or once the electricity supply is restored.
* Only available in selected models.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash options
Half load
EN
If there are not many dishes to be washed, a half load
cycle may be used in order to save water, electricity and
detergent. Select the wash cycle and press the HALF
LOAD button: the indicator light will illuminate.
The OPTIONS may only be set, modified or reset after
the wash cycle has been selected and before the
Start/Pause button has been pressed.
Only the options which are compatible with the type of
wash cycle set may be selected. If an option is not com-
patible with the selected was cycle (see Table of wash
cycles), the corresponding LED flashes rapidly 3 times.
Remember to halve the amount of detergent.
It is better to use powder detergent in this case.
This option is incompatible with the following wash
cycle: Rapid wash, Intensive Speed+ and Normal
Speed+.
If an option is selected which is incompatible with another
option or wash cycle selected previously, the incompat-
ible option light will flash 3 times and switches off, while
the most recently selected setting remains lit.
Multi-functional tablets (Tabs)
This option optimises washing and drying results.
When using multi-functional tablets, press the MULTI-
FUNCTIONAL TABLETS button. The corresponding indicator
light will illuminate. The “Multi-functional tablets” option
results in the lengthening of the wash cycle.
To deselect an option which has been set by mis-
take, press the corresponding button again.
Delayed start
The start of the wash cycle may be delayed for a period
of time between 1 and 24 hours.
The MULTI-FUNCTIONAL TABLETS option remains
set for subsequent wash cycles if it is not deselected.
1. After selecting the desired wash cycle and any other
options, press the DELAYED START button: the
corresponding indicator light will illuminate. Use the
same button to select the time at which you wish the
wash cycle to begin (after a period of 1 to 24 hours).
2. Confirm your selection using the Start/Pause button;
the countdown will begin. The selected delay period
indicator light is displayed and the Start/Pause button
stops flashing (the light becomes fixed instead).
3. When the set time has elapsed, a long beep sounds,
the DELAYED START indicator light switches off and the
wash cycle begins.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL TABLETS
option.
This option is not recommended for use with wash
cycles which do not specify the use of multi-functional
tablets (see Table of options).
This option is incompatible with the following wash
cycle: Soak.
A
B
C
To deselect the DLEAYED START option, press the
DELAYED START button repeatedly until the text OFF
appears.
Table of options
Delayed Half
Tabs
Start
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Load
Yes
Yes
Yes
Yes
No
1. Intensive
2. Time4you
3. Soak
Yes
Yes
No
The Delayed Start function cannot be set once the
wash has been started.
4. Eco
Yes
Yes
Yes
Yes
Yes
5. Rapid
6. Delicate
Yes
No
7. Intensive Speed+
8. Normal Speed+
No
* Only available in selected models.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash cycles
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
EN
The number and type of wash cycles and options may vary depending on the dishwasher model.
For available OPTIONS please refer to the Table of options on the Start-up and use page.
Detergent
(A) = compartment A
(B) = compartment B
Wash
cycle
duration
(tolerance
10%)
Wash
cycles
which
include
drying
Wash cycle selection
instructions
Wash cycle
Options
Powder
Liquid
Tablets
Hrs. Min.
Heavily soiled dishes and pans
(not to be used for delicate
items).
1.Intensive
35 g (A)
35 ml (A)
1 (A)
1 (A)
Yes
Yes
A-B-C
A-B-C
2:15’
1:45’
Normally soiled pans and
dishes. Standard daily wash
cycle.
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
2. Time4you
Pre-wash for dishes while
awaiting completion of the load
with the dishes from the next
meal.
3. Soak
No
No
No
No
A-B
0:08’
2:40’
Environmentally-friendly wash
cycle with low energy
consumption levels, suitable for
pans and dishes.
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
4. Eco*
1 (A)
Yes
A-B-C
Economic and fast wash to be
used for lightly soiled dishes.
(Run cycle immediately after
use) (2 plates + 2 glasses + 4
pieces of cutlery + 1 saucepan
+ 1 small frying pan).
5. Rapid
wash
25 g (A)
25 ml (A)
1 (A)
1 (A)
No
A-C
0:25’
1:30’
Economic and fast wash for
delicate items which are
sensitive to high temperatures.
(Run cycle immediately after
use) (glasses upper rack +
delicate plates lower rack).
6. Delicate
35 g (A)
35 g (A)
35 g (A)
Yes
A-B-C
Quick wash and dry cycle,
suitable for heavily soiled
crockery and pans (not suitable
for delicate items).
7. Intensive
Speed+
35 ml (A)
1 (A)
1 (A)
Yes
Yes
A-C
A-C
1:40’
1:20’
Quick wash and dry cycle,
suitable for crockery and pans
with a normal soil level.
8. Normal
Speed+
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
Notes:
Optimum performance levels when using the "Rapide wash" cycles can be achieved by observing the maximum amounts of crockery
specified.
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid
*The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less
energy and is les harmful to the environment.
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following
address: [email protected]
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rinse aid and refined salt
button repeatedly until the desired hardness level has been
Only use products which have been
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
EN
reached (1-2-3-4-5* see Water hardness table), up to a
maximum of five levels.
- To exit the function, wait approximately 30 seconds or switch
off the machine using the ON/OFF button.
Follow the instructions given on the packaging.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
If using a multi-functional product it is not necessary to
add rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard. Follow the instructions given on the packaging.
Water Hardness Table
°dH
0
°fH
mmol/l
level
6
0
10
0
1
1
2
3
4
If you do not add salt or rinse aid, the LOW
SALT* and LOW RINSE AID* indicator lights
remain lit.
6
11 11
20 1.1
30 2.1
60 3.1
90 6.1
2
3
6
9
12 17 21
17 34 31
34 50 61
*
5
For values between 0°f and 10°f, we do not
Measuring out the rinse aid
recommend the use of salt.
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
* this setting may cause a slight increase in the
duration of the cycle.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
The rinse aid dispenser should be filled:
• When the LOW RINSE AID*indicator light on the control
panel/dislay is illuminated;
1. Open the dispenser by turning
the lid (G) in an anticlockwise
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty.
Refined salt removes limescale from the water, thus
avoiding the formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher (see Description) and should be filled:
• When the green float* cannot be seen by simply looking at
the cap of the salt dispenser.
direction.
2. Pour in the rinse aid, making
sure it does not overflow from the
dispenser. If this happens, clean
F
the spill immediately with a dry
G
cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly into the appliance tub.
• When the LOW SALT*indicator light on the control panel/
display is illuminated;
Adjusting the amount of rinse aid
1. Remove the lower rack and unscrew
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
• If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
the container cap (anticlockwise).
2. The first time you do this: fill the water
tank right up to its edge.
3. Position the funnel*(see figure) and
fill the salt container right up to its edge
(this should hold approximately 1 kg); it is not unusual for a
little water to leak out.
• If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
4. Remove the funnel* and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it
on, the head facing downwards so as to let the water flow out
of the four cracks which are arranged in a star shape on the
lower part of the cap. (Salt cap with green float*)
It is advisable to perform this procedure every time you
add salt to the container.
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from your local water supplier.
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
- Switch on the appliance by pressing the ON/OFF button.
- Press the P button and hold for approximately 5 seconds;
two short beeps will sound, the text H2O will appear on the
display and the set hardness number will flash (the water
softening system is set by default to number 3). Press the P
* Only available in selected models.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Clean the water inlet filter at the tap outlet regularly.
Shutting off the water and electricity
supplies
• Turn off the water tap after every wash cycle to avoid
EN
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter and
clean it carefully under running water.
leaks.
- Replace the filter and screw the water hose back into
• Always unplug the appliance when cleaning it and
when performing maintenance work.
position.
Cleaning the dishwasher
Cleaning the filters
• The external surfaces of the machine and the control
panel may be cleaned using a non-abrasive cloth
which has been dampened with water. Do not use
solvents or abrasive products.
The filter assembly consists of three filters which remove food
residues from the washing water and then recirculate the
water. They should be cleaned if you wish to achieve the best
results in every wash.
• Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a
little vinegar.
Clean the filters regularly.
The dishwasher should not be used without filters, or if the
filter is loose.
Preventing unpleasant odours
• Always keep the door of the appliance ajar in order to
avoid moisture from forming and being trapped inside
the machine.
• After several washes, check the filter assembly and if
necessary clean it thoroughly under running water, using a
non-metallic brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction
and pull it out (fig. 1).
• Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This will
avoid food becoming trapped in the seals, which is
the main cause behind the formation of unpleasant
odours.
2. Remove the cup filter B by exerting a slight pressure on the
side flaps (fig. 2).
3. Slide out the stainless steel plate filter A (fig. 3).
4. Inspect the trap and remove any food residue. NEVER
REMOVE the wash cycle pump (black detail) (fig. 4).
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer
arms and block the holes used to spray the water. It is
therefore recommended that the arms are checked from
time to time and cleaned with a small non-metallic
brush.
B
C
The two sprayer arms may both be removed.
C
1
2
To remove the upper sprayer
arm, rotate the locking ring in
an anti-clockwise direction.
The upper sprayer arm should
be replaced with the holes
facing upwards.
A
The lower sprayer arm can be
removed by pressing on the
side tabs and pulling it
upwards.
3
4
After cleaning the filters, replace the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
Leaving the machine unused for extended
periods
• Disconnect the appliance from the electricity supply and
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it
is clear and free of impurities before performing the
necessary connections. If this precaution is not taken,
the water inlet could become blocked and damage the
dishwasher.
shut off the water tap.
• Leave the door of the appliance ajar.
• When you return, run a wash cycle when the dishwasher is
empty.
* Only available in selected models.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
This appliance was designed and manufactured in
Saving energy and respecting the
environment
EN
compliance with current international safety standards. The
following information has been provided for safety reasons
and should therefore be read carefully.
Saving water and energy
• Only begin a wash cycle when the dishwasher is full. While
waiting for the dishwasher to be filled, prevent unpleasant
odours using the Soak cycle (see Wash cycles).
• Select a wash cycle which is suited to the type of crockery
and to the soil level of the crockery using the Table of wash
cycles:
General safety
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
- For dishes with a normal soil level, use the Eco wash
cycle, which guarantees low energy and water
consumption levels.
• Children should be supervised to ensure that they do not
play with the appliance.
- If the load is smaller than usual activate the Half load
option*(see Start-up and use).
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial use.
• The appliance must be used by adults only, to wash
domestic crockery in accordance with the instructions in
this manual.
• If your electricity supply contract gives details of electricity
saving time bands, run wash cycles during the periods
when a lower tariff is applied. The Delayed start*button
(see Start-up and use) helps you organise the wash cycles
accordingly.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
machine exposed to rain and storms.
Phosphate-free and chlorine-free detergents
containing enzymes
• Do not touch the appliance when barefoot.
• When unplugging the appliance always pull the plug from
the mains socket, do not pull on the cable.
• We strongly recommend that you use detergents that do
not contain phosphates or chlorine, as these products are
harmful to the environment.
• The water supply tap must be shut off and the plug should
be removed from the electrical socket before cleaning the
appliance or carrying out any maintenance work.
• If the appliance breaks down, do not under any
circumstances touch the internal parts in an attempt to
perform the repair work yourself.
• Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result detergents
containing enzymes can be used in conjunction with low-
temperature wash cycles in order to achieve the same
results as a normal 65°C wash cycle.
• Never touch the heating element.
• Do not lean or sit on the open door of the appliance: this
may cause the appliance to overturn.
• To avoid wasting detergent, use the product in appropriate
quantities based on the manufacturer’s recommendations,
the hardness of the water and the soil level and quantity of
crockery to be washed. Even if they are biodegradable,
detergents contain substances which may alter the balance
of nature.
• The door should not be left open as it may create a
dangerous obstacle.
• Keep detergent and rinse aid out of reach of children.
• The packaging material should not be used as a toy.
Disposal
• Disposal of packaging materials: observe local legislation
so that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using the
normal solid urban waste cycle. Exhausted appliances
should be collected separately in order to optimise the cost
of re-using and recycling the materials inside the machine,
while preventing potential damage to the atmosphere and
to public health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations regarding
separated waste collection.
For further information relating to the correct disposal of
household appliances, owners may contact the relevant
public authority or the local appliance dealer.
* Only available in selected models.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for
Assistance.
EN
Malfunction:
Possible causes / Solutions:
The dishwasher does not start.
• The plug has not been inserted into the electrical socket properly, or
there is no power in the house.
• The dishwasher door has not been shut properly.
see Start-up and use
• A delayed start has been programmed (
).
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet finished.
see Installation
• The water outlet hose is bent (
• The drain duct is blocked.
).
• The filter is clogged up with food residues.
The dishwasher makes
excessive noise.
• The dishes are rattling against each other or against the sprayer arms.
•
An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
The dishes and glasses are
covered in a w hite film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to
see Rinse aid and salt
the hardness of the water (
).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
• The rinse aid dosage is too high.
streaked or have a bluish tinge.
The crockery has not been
dried properly.
• A wash cycle without a drying programme has been selected.
see Rinse aid
• The rinse aid has been used up or the dosage is too low (
and salt
).
• The rinse aid dispenser setting is not high enough.
The dishes are not clean.
•
•
•
•
•
The racks are overloaded (see Loading the racks).
The crockery has not been arranged well.
The sprayer arms cannot move freely.
The wash cycle is too gentle (see W ash cycles).
An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
•
•
•
The lid on the rinse aid compartment has not been shut correctly.
The filter is dirty or blocked (see Care and maintenance).
The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take
any water in/Tap shut-off alarm.
(several short beeps are emitted)
•
•
•
•
There is no water in the mains supply.
see Installation
The water inlet hose is bent (
).
Turn on the tap and the appliance will start after a few minutes.
The appliance lock has been activated because no action was taken
when the beeps sounded. Switch off the m achine using the ON/OFF
button, turn on the tap and switch the machine back on after 20
seconds by pressing the same button. Re-programme the machine and
restart the wash cycle.
(The display shows A:6).
W ater intake solenoid valve
malfunction alarm
(The display shows A:2).
•
•
Switch off the appliance by pressing the ON/OFF button and switch it
back on after one minute. If the alarm continues, shut off the water tap
to eliminate the risk of flooding, remove the plug from the electrical
socket and contact Assistance.
W ater inlet hose alarm/W ater
inlet filter blocked.
Switch off the appliance by pressing the ON/OFF button. Shut off the
water tap to eliminate the risk of flooding and remove the plug from the
electrical socket.
(the display shows A:7).
Make sure the water inlet filter has not become blocked by various
impurities. (see “Care and maintenance” chapter).
* Only available in selected models.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
195075755.00
02/2009 - Xerox Fabriano
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|