Indesit Dishwasher IDE 1000 User Manual

IDE 1000  
IDE 1005  
Dishwasher  
Installation and use  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Is a Good Habit to Get Into  
NOTICE  
5.Keep detergents out of the reach of children, who must also be  
kept away from the dishwasher when it is open.  
6.This appliance cannot be installed outdoors, not even if the area in  
which it is installed is covered by a roof; it is also very dangerous to  
leave it exposed to the rain and elements.  
7.Do not touch the heating element during or after a wash cycle.  
8.Do not lean or sit on the door when it is open, as this could overturn  
the dishwasher.  
9.If the appliance malfunctions, turn off water supply to the appliance  
and disconnect the plug from the wall socket. Then, consult the  
section entitled, " Troubleshooting." If you cannot resolve the  
problem, contact a service centre.  
Carefully read the instructions contained in this manual, as they  
provide important information which is essential to safe and proper  
installation, use and maintenance of the appliance.  
This appliance complies with the following EEC directives:  
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent  
modifications;  
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)  
and subsequent modifications.  
- 97/17/EEC Labelling  
1.Carefully dispose of the packing material.  
10.Appliances which are no longer being used must be made  
inoperable by cutting the power supply cord and removing the door  
lock.  
2.After removing the packing, check to make sure that the appliance  
is not damaged. If in doubt, contact a qualified professional.  
3.The dishwasher must only be used by adults for the washing of  
household dishes and cooking utensils.  
4.Fundamental rules to follow when using the appliance:  
- Never touch the dishwasher when barefoot or with wet hands or  
feet;  
- We discourage the use of extension cords and multiple sockets;  
- During installation, the power supply cord must not be excessively  
or dangerously bent or flattened;  
To maintain the EFFICIENCY and SAFETY of this  
appliance, w e recommend:  
l call only the Service Centers authorized  
by the manufacturer  
l alw ays use original Spare Parts  
- If the appliance is not operating properly or maintenance must  
be performed, disconnect the appliance from the power supply.  
Close-up View (control panel)  
H
D
R
A
Time 4 You  
Eco  
eco  
Rapid'25  
Intensive  
Soak  
Crystal Care  
Just You  
E
G
C
F
H: Display  
E: "Extra drying" button  
F: "Half load" button  
A: ON-OFF button  
C: Door handle  
R: Start/Reset Button  
G: Delayed start select button  
L
H
T
G: "Extra drying" indicator light  
H: Cycle phase indicator lights  
L: Alphanumeric indicator  
N: Half load indicator light  
S: Low salt indicator light  
T: Low rinse aid indicator light  
I: Delayed start indicator light  
S
I
G
N
GB  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Close-up View (Interior)  
E
G
F
H
J
I
K
L
Bottom Sprayer Arm  
Upper Rack  
Salt Container Cap  
Washing Filter  
Top Sprayer Arm  
Rack Height Adjustor  
Low er Rack  
Detergent and Rinse Aid Dispenser  
7HFKQLFDO ꢀꢀꢀꢀꢀꢀFKDUDFWHULVWLFV  
Width  
cm. 60  
Depth  
cm. 60  
Height  
cm. 85  
12 standard place settings  
Capacity  
Mains water pressure  
Power voltage  
Total absorber power  
Fuse  
4,3 psi - 145 psi (30 KPa÷ 1MPa) (0,3 ÷10 bar)  
See data plate  
See data plate  
See data plate  
GB  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Salt ......  
Salt  
Adjusting Salt Consumption  
The hardness of the water varies from place to place. If  
hard water is used in the dishwasher, deposits will form on  
the dishes and utensils.  
The dishwasher is designed to allow for adjusting the  
amount of salt consumed based  
on the harness of the water  
The appliance is equipped with a special softener that uses  
a salt specifically designed to eliminate lime and minerals  
from the water.  
used. This is intended to  
optimize and customize the  
level of salt consumption so that  
it remains at a minimum.  
Your Local Water Board can  
supply the degree of hardness  
Loading the Salt into the Softener  
Always use salt intended  
for use with dishwashers.  
of the water  
The salt container is  
in your area.  
located beneath the  
To adjust salt consumption, pro-  
lower rack and should be  
ceed as follows:  
filled as follows:  
1. Remove the lower rack  
and then unscrew and  
remove the cap from the  
salt container;  
2. If you are filling the  
container for the first  
1) Unscrew the cap from the salt container.  
2) There is a ring on the container with an arrow on it (see  
figure to the side), if necessary, rotate the ring in the anti-  
clockwise direction from the "_" setting towards the " +"  
sign, based on the hardness of the water being used.  
It is recommended that adjustments be made in accord-  
ance with the following schema:  
time, fill it with water;  
3. Place the end of the funnel (supplied) into the hole and  
introduce about 2 kg of salt. It is normal for a small amount  
of water to come out of the salt container.  
4. Carefully screw the cap back on.  
Water Hardness  
The salt container should be filled up w hen the low  
salt indicator light "S" flashes.  
Once you have loaded the salt for the first time, it is normal  
that the low salt indicator light stays on or flashes for about  
5 consecutive cycles.  
Salt  
Autono-  
consu-  
Clarke  
degrees  
Selector  
position  
my  
°fH  
mmol/l  
mption  
(grams/-  
cycle)  
(cycles\2-  
kg)  
0 - 14  
0 - 17  
0 -1,7  
/
0
/
Warning: To prevent rust from forming, we advise you to  
load the salt before starting a wash cycle.  
14 - 36  
18 - 44 1,8 - 4,4  
"-"  
20  
40  
60  
60  
40  
25  
36 - 71 45 - 89 4,5 - 8,9  
>71 > 89 > 8,9  
MED  
"+"  
GB  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Detergent and Rinse Aid ....  
Rinse Aid  
Detergent  
This product makes dishes sparkle more as it improves their  
drying. The rinse aid container is situated on the inside of  
the appliance door; you should refill it when the low rinse  
aid indicator light "T" flashes.  
Detergent specifically intended for use with dishwashers  
must be used. The dispenser must be refilled before the  
start of each wash cycle following the instructions provided  
in the " Wash Cycle Table." The detergent dispenser is  
located on the inside panel of the door.  
Loading the Rinse Aid  
To open the dispenser, turn the "C" cap in the anti-clockwise  
direction and then pour in the rinse aid, making sure not to  
overfill. The amount of rinse aid used for each cycle can be  
regulated by turning the "F" dose adjustor, located beneath  
the " C" cap, with a screwdriver. There are 6 different  
settings; the normal dosage setting is 4.  
Loading the detergent  
To open lid "A", press button "B". The cleaning detergent  
should be introduced into the two containers " C"and  
"D" up to the rim.  
After pouring in the detergent, replace the lid, pressing  
down until it clicks.  
Dishwasher detergent in tablets is now available on the  
market, in which case you should place one tablet into  
container "D" and replace the lid.  
F
C
C
B
D
Important:  
Proper dosage of the rinse aid improves drying.  
If drops of water remain on the dishes or spotting occurs,  
the dosage adjustor should be turned to a higher setting. If  
the dishes have white streaks, turn the dosage adjustor to  
a lower setting.  
A
Notice: To facilitate closing the cover, remove any  
excess detergent on the edges of the dispenser.  
Warning  
Three-in-one dishwasher tablets are now available on the market, and combine detergent, salt and rinse aid all in one.  
If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent the  
formation of white streaks on your dishes or on the interior of the appliance.  
Using a three-in-one product means it is no longer necessary to put rinse aid into the relevant container.  
If you want to achieve perfectly dry dishes, you may add rinse aid as long as the dosage adjuster is set to no.2.  
In any case, please read the manufacturer's instructions on the packet.  
If you use only these products, it is normal for the salt and rinse aid indicator lights to flash permanently after a certain number  
of cycles.  
GB  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Loading the Dishw asher  
Before placing the dishes in the racks, remove the largest  
scraps of food left over on your plates, you will thus avoid  
blocking the filter, which would reduce the efficacy of the  
wash.  
Load examples  
low er rack  
upper rack  
If the saucepans and frying pans are very dirty, allow them to  
soak before being washed.  
You will thus avoid having to wash them again.  
To make it easier to load your dishes, pull the racks out fully.  
How to use the low er rack  
We recommend you place the most difficult dishes to wash  
into the lower rack: saucepans, lids, soup dishes and plates  
(load examples are shown in the photo).  
• Serving dishes and large lids: place them on the sides  
of the rack.  
• Saucepans, salad bow ls: must always be placed upside  
down.  
Very deep dishes: place them obliquely, thus allowing  
water to run down them and cleaning them better.  
The cutlery basket (Figures A)  
Insert the cutlery into the basket: knives and utensils with  
sharp blades or tips should be positioned with the sharp  
parts at the bottom. Position all cutlery items so that they  
don't touch.  
A
A
If the rack has side baskets, the spoons should be loaded  
individually into the appropriate slots (see fig. A).  
- Especially long utensils should be placed in the horizon-  
tal position at the front of the upper rack.  
How to use the upper rack  
Place delicate and lightweight dishes in the upper rack:  
glasses, tea cups and coffee cups, saucers - but plates too  
- shallow salad bowls, slightly dirty frying pans and shallow  
pans (the photo illustrates a few examples).  
Position lightweight dishes in such as way as to avoid their  
being moved by the spray of water.  
- The upper rack can be equipped with one or two special  
tip-up compartments for mugs and cups, as well as spoons,  
knives and forks, which should be fitted in the slots  
provided. Stemmed glasses can be hooked onto these  
compartments by threading the stems into the slots  
provided (see fig. D).  
fig. D  
After loading the dishes, remember to check that the blades  
on the sprayer arms can turn freely without knocking  
against any dishes.  
1
2
4
How to adjust the upper rack ….  
The upper rack can be set in a high or low position. To do  
so, open the rail stop flaps and pull the rack out completely;  
now place it with the back wheels in high or low position,  
then slide it along the guide rails until the front wheels also  
go in; now close the rail stop flaps (see fig. F).  
3
Fig. F  
GB  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning on the Appliance  
You've left out a dish?  
First of all  
You can interrupt a wash cycle by pressing the "ON-OFF"  
button, then place the forgotten dishes into the appliance,  
which will start up, after approximately 10 seconds, from  
where it was interrupted when you turn it back on.  
After performing all the operations described in the previous  
paragraphs, turn the water tap on completely and press ON-  
OFF button " A": you will hear a short beep, the display lights  
up and the wash cycle time selected on the knob will flash.  
There's been a pow er failure? Has the dishw asher door  
been opened?  
The wash cycle stops and 3 dashes appear on the display;  
the cycle restarts as soon as the electricity comes back on or  
when the door is shut.  
Selecting and starting a w ash cycle.  
• Select the desired wash cycle by turning knob " D"  
clockwise from wash cycle 1 to 7 and anticlockwise from 7  
to 1; the display indicates the average duration of the wash  
cycle and the cycle phases it consists of (consult the wash  
cycle table contained on page 7, especially when first using  
the appliance).  
At the end of the w ash cycle  
The end of the wash cycle is indicated by two short beeps  
and the word "END" flashes on the display.  
• Press the Start button "R" and the wash cycle starts up,  
emitting a double beep; the approximate amount of time  
left until the end of the wash cycle is displayed.  
Warning:  
Turn the appliance off by pressing button “A”, unplug  
the appliance from the electricity socket to cut off the  
p o w e r su p p ly; t h e p o w e r su p p ly ca b le sh o u ld  
consequently be easily accessible.  
If the time indicated at the start of the wash cycle does  
not correspond to the actual duration of the cycle itself, this  
could be for a number of reasons: the temperature of the  
inlet water, the degree of soil, prolonged attempts by the  
appliance to clean the wash filter from food residue clogging  
it, etc.  
Turn off the water tap.  
Empty the lower rack first.  
Cycle phase under w ay indicator  
While the wash cycle is under way, the symbols corresponding  
to the cycle phases light up in sequence.  
Make sure the wash cycle has ended before removing the  
dishes!  
Here are the symbols corresponding to each cycle phase:  
Warning: when you open the dishwasher door after the wash  
cycle has just ended or is under way, take care not to scald  
yourself with the hot steam.  
Pre-wash  
Wash  
Rinses  
Drying  
Cancelling and modifying a w ash cycle in progress  
Premise: a wash cycle in progress can only be modified if it  
hasn't been running for long.  
Keep the Reset button " R" pressed for about 3 seconds:  
a prolonged beep will sound, followed by three short beeps.  
The cancelled cycle time will flash on the display. Turn the  
knob to select a new wash cycle.  
How to set the extra drying  
Press button "E". After a prolonged beep, indicator light  
"G" lights up and the time corresponding to the wash cycle  
selected on the knob will flash on the display.  
Note: The time indicated on the display is extended due to  
the extra drying time.  
To disable the extra drying option, press the same button  
and indicator light "G" will be turned off after a beep is  
sounded.  
This option is incompatible with the soak cycle.  
GB  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting a half load and a delayed start  
How to set a delayed start  
You w ant to w ash on one rack only?  
When you have loaded the dishes, you can choose when to  
start your dishwasher before setting the wash cycle desired.  
• Press button "G" repeatedly to postpone the start of the  
wash cycle from 1 hour to 24h.  
Remember to use half the amount of detergent.  
When you only have little cutlery to wash, you can run just  
half a load on the upper rack, saving on both water and  
electricity.  
If you press the button again, the word "OFF" is displayed  
(no selection made).  
Once you have made your selection, make sure the appliance  
door is shut and start the wash cycle by pressing the START  
button.  
• Press button " F"; you will hear a beep and the symbol  
corresponding to the half load will light up.  
Once you have made your setting, start the wash cycle by  
pressing the START button.  
- This option is available with all wash cycles.  
- The Just You wash cycle is programmed to wash on the  
upper rack only.  
Symbol " I" lights up on the display and the countdown  
begins.  
• Once the countdown is up, the wash cycle begins and the  
approximate amount of time left until the end of the wash  
cycle is displayed.  
Have you changed your mind?  
If you change your mind, you can set a shorter time delay:  
press button "G" to select it. You need not reset the wash  
cycle.  
Warning: if the display indicates the word "dON" when you turn  
your dishwasher on, this means the demo mode is in operation. This  
mode is useful for exhibitors in that it simulates the wash cycles  
without actually carrying them out.  
To quit this mode, keep the START/RESET button "R" pressed for  
approximately 4 seconds. The word "dOF" will be displayed once  
you have quit the demo mode successfully.  
If you have changed your mind and wish to start the wash  
cycle immediately, press button " G" until the countdown is  
fully reset. Indicator light " I" will turn off and the cycle will  
start at the sound of a beep.  
The indicator light corresponding to the cycle phase under  
way will come up on the display and the countdown to the  
estimated cycle end begins.  
GB  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wash Cycle Table  
Dishw asher w ashing guarantees your dishes w ill be cleaned in a hygienic setting for  
safer, cleaner results.  
:DVKꢀF\FOH  
GXUDWLRQ  
ꢃ“ꢄꢅꢆ  
PDUJLQ  
ZLWKRXW  
H[WUD  
'HWHUJHQW  
IRUꢀSUHꢁ  
ZDVKꢀꢂ  
ZDV K  
&\FOHꢀVHOHFWLRQ  
LQVWUXFWLRQV  
&\FOH  
&\FOHꢀGHVFULSWLRQ  
5LQVHꢀ$LG  
GU\LQJꢇ  
Pre-wash with hot water at 40°C  
Wash at 65°C  
2 cold rinses  
Hot rinse at 65°C  
Drying. .  
Ve ry d ir ty d is he s a nd  
pans (not to be used  
for delicate items)  
ꢄꢉꢅꢋ  
ꢎꢉꢋ  
ꢈꢂꢉꢈꢀJ  
ꢍꢅꢀJ  
,QWHQVLYH  
Normally dirty pans  
and dishes. Standard  
daily cycle.  
Wash at 50°C.  
Cold rinse  
Hot rinse at 70°C  
Drying.  
7LPHꢀꢌꢀ<RX  
Environmentally-frien-  
dly cycle, with low  
energy consumption  
levels, suitable for  
normally dirty pans  
and dishes.  
2 pre-washes with cold water  
Wash at 50°C  
Hot rinse at 65°C  
ꢈꢂꢉꢈꢀJ  
ꢄꢉꢅꢋ  
Drying  
(FR  
Economic and fast  
cycle to be used for  
slightly dirty dishes.  
Run cycle immediately  
after use. Without  
drying except when  
the extra drying option  
has been selected.  
Short wash at 50°C  
Rinse at 62°C  
Drying only if selected  
ꢉꢈꢀJ  
ꢉꢈꢋ  
(with extra  
drying)  
5DSLGꢀꢉꢈꢋ  
6RDN  
Preliminary wash cycle  
for dishes and pans  
awaiting completion of  
the load with the dishes  
from the next meal.  
Short cold wash to prevent food from  
drying onto the dishes.  
ꢄꢉꢋ  
ꢏꢐꢋ  
Special cycle to be  
used for delicate  
items, which are more Hot rinse at 65°C  
sensitive to high  
temperatures.  
Wash at 52°C  
Rinse at 45°C  
ꢉꢈꢀJ  
ꢉꢈꢀJ  
Drying  
&U\VWDOꢀ&DUH  
Quick and economic  
wash for a daily load  
of dishes. This may  
only be done on the  
upper rack.  
Wash at 50°C  
Hot rinse at 67°C  
ꢌꢅꢋ  
-XVWꢀ<RX  
GB  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Energy Saving Tips  
- Use the right amount of detergent: if you use too much  
detergent, the result will not be cleaner dishes, but, rather,  
a greater negative impact on the environment.  
- It is important to try and run the dishwasher when it is  
fully loaded in order to save on energy. In order to prevent  
odors from forming and food from caking onto the dishes,  
you can run the hold cycle.  
- There is no utility in rinsing dishes, cookware and utensils  
before placing them in the dishwasher.  
- Choose the right wash cycle: the choice of cycle depends  
on the type of dishware, cookware and utensils being  
washed and how dirty they are.  
How to Keep Your Dishw asher in Shape  
When You Go on Holiday  
After Every Wash  
When you go on holiday, it is recommended that you run a  
wash cycle with the dishwasher empty and then remove  
the plug from the socket, turn off the water supply and  
leave the door of the appliance slightly ajar. This will help  
the seals last longer and prevent odors from forming within  
the appliance.  
After every wash, turn off the water supply to the appliance  
and leave the door slightly ajar so that moisture and odors  
are not trapped inside.  
Remove the Plug  
Before cleaning or performing maintenance, always remove  
the plug from the socket. Do not run risks.  
Moving the Appliance  
If the appliance must be moved, try to keep it in the vertical  
position. If absolutely necessary, it can be positioned on its  
back.  
No Solvents or Abrasive Cleaning Products  
To clean the exterior and rubber parts of the dishwasher,  
do not use solvents or abrasive cleaning products. Rather,  
use only a cloth and warm soapy water.  
Seals  
To remove spots or stains from the surface of the interior,  
use a cloth dampened with water and a little white vinegar,  
or a cleaning product made specifically for dishwashers.  
One of the factors that cause odors to form in the  
dishwasher is food that remains trapped in the seals. Periodic  
cleaning with a damp sponge will prevent this from occuring.  
GB  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning and Special Maintenance  
The filter assembly  
If you want consistent good results from your dishwasher,  
you need to clean the filter  
assembly.  
The food particles are  
removed from the wash  
water, allowing it to be  
recirculated during the  
cycle, filtered perfectly. For  
this reason, it is a good idea  
to remove the larger food  
particles trapped inside the  
cup “C” and the semi-circular filter A after each wash; pull  
the cup handle upwards to remove them. Just rinse them  
under running water.  
For cleaning, use a non metallic brush.Reassemble the filter  
parts (as shown in the figure) and reinsert the whole assembly  
into the dishwasher. Position it into its housing and press  
downwards.  
The dishwasher is not to be used without filters. Improper  
replacement of the filters may reduce the efficiency of the  
wash and even damage your dishwasher.  
1
A
B
2
Cleaning the Sprayer Arms  
It may happen that food particle become encrusted on the  
sprayer arms and block the holes (see " Close up view  
(interior)", letters F-I). Check the sprayer arms periodically  
and clean them when needed.  
C
The entire filter assembly should be cleaned thoroughly once  
a month: cup C + semi-circular filter A + cylindrical filter B.  
Rotate filter “Banticlockwise to remove it.  
Troubleshooting  
It may occur that the dishwasher does not function or does not  
function properly. Before calling for assistance, let us see what can  
be done first: have you forgot to press one of the buttons or to  
perform an essential operation?  
The Dishw asher Does Not Start  
Have you checked whether:  
- the plug is pushed into the socket correctly;  
- the power is on in the house;  
- the door is closed properly;  
Error messages.  
Your dishwasher is equipped with a safety system which is able to  
detect any operating anomalies.  
These anomalies or faults are signalled by several codes consisting of  
letters and numbers that flash up on the display. Make a note of the  
error code that appears, turn the appliance off, turn off the water  
tap and call for technical assistance.  
Tap off alarm  
- the ON-OFF switch is on "ON";  
- the water supply is turned on.  
The Dishw asher Does Not Load Water  
Have you checked whether:  
- the water is turned on and the hose is connected properly;  
- the water supply to the house is on and has sufficient  
pressure;  
- the water supply hose is crimped or bent;  
- the filter for the water supply hose is clogged.  
The Dishes Are Not Clean  
Have you put the right amount of detergent into the dispenser?  
Is the wash cycle suitable for the dishes you have placed inside the  
appliance?  
If you have forgotten to turn on the water tap, the appliance will  
remind you with a series of prolonged beeps and the wording H2O  
will flash up on the display. Turn the tap on and the wash cycle will  
start up after a few minutes.  
If you are not there when the H2O signal appears, the appliance will  
switch to alarm mode and the code "A06" will flash on the display.  
Turn the appliance off at button "A", turn on the water tap and wait  
approximately 20 seconds before turning the appliance back on, the  
wash cycle will start up again.  
Clogged filter alarm  
If the appliance is blocked and the code "A05" is flashing, this  
means the filter is clogged by large particles of food residue. Turn  
the appliance off at the ON-OFF button, clean the filter thoroughly  
and reposition it in its seat, then turn the appliance back on. The  
wash cycle will start up as normal after a few seconds.  
Are the filter and microfilter clean?  
Can the sprayer arms turn freely?  
The Dishw asher Does Not Drain  
Have you checked whether:  
- the drain hose is crimped or bent.  
Lime Deposits or a White Film Form on the Dishes  
Have you checked whether:  
- the lid to the salt container is closed properly;  
- the rinse aid dosage is correct.  
Water load solenoid valve malfunction alarm  
If the code "A02" flashes, first of all turn off the water tap to avoid  
any flooding and then cut off the electricity supply and call for  
assistance.  
If, despite all these checks, the dishwasher still does not function  
and/or the problem persists, contact the nearest authorised service  
centre and provide them with the following information:  
- the nature of the problem;  
If the display indicates the w ord "dON" w hen you turn your  
dishw asher on, this means the demo mode is in operation.  
Read the instructions on pages 7.  
- the model type number (Mod. ...) and the serial number (S/N ....),  
which are indicated on the plate located on the side of the inner part  
of the door.  
Never call on unauthorised technicians and refuse to allow  
parts to be installed that are not original spare parts.  
GB  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Positioning the Appliance  
Drain Hose Connection  
A
Position the appliance in the desired location. The back  
should rest against the wall behind it, and the sides, along  
the adjacent cabinets or wall. The dishwasher is equipped  
with water supply and drain hoses that can be positioned  
to the right or the left to facilitate proper installation.  
Fit the drain pipe into a drain  
line with a minimum diameter  
of 4 cm or place it over the  
sink. Avoid restricting or  
bending it. Use the special  
plastic elbow provided (see fi-  
gure) to position it in the best  
possible way. The part of the  
pipe marked with the letter A  
should be between 40 and 100  
cm above the ground.  
Levelling the Appliance  
Once the appliance is positioned, adjust the feet (screwing  
them in or out) to adjust the height of the dishwasher,  
making it level. In any case, the appliance should not be  
inclined more than 2°.  
If the appliance is level, it will help ensure proper perfor-  
mance.  
The pipe should not be immersed in water.  
Attention: The special plastic hose support must be solidly  
fastened to the wall to prevent the drain hose from moving  
and allowing water to spill outside the drain.  
This dishwasher model can be built under a single worktop  
(please read the relevant instruction sheet).  
Cold Water Connection  
Electrical Connection  
This electric household appliance should be connected to  
the water mains using the cold water supply hose provided  
with the appliance only. Do not use a different hose. In the  
event of replacements, use original spare parts only.  
Connect the cold water supply hose to a threaded 3/4 (gas)  
connector and making sure that it is fastened tightly in place.  
If the water pipes are new or have not been used for an  
extended period of time, let the water run to make sure that  
the water is clear and free of impurities. If this precaution is  
not taken, there is a risk that the water inlet can get blocked  
and damage the appliance.  
After making sure that the voltage and frequency values for  
the current in the home correspond to those on the rating  
plate (located on the stainless steel inner door of the  
appliance) and that the electrical system is sized for the  
maximum voltage on the rating plate, insert the plug into  
an electrical socket which is earthed properly (the earthing  
of the appliance is a safety requirement mandated by law).  
If the electrical socket to which the appliance must be  
connected is not appropriate for the plug, replace the plug,  
rather than using adpators or the like as they could cause  
overheating and burns.  
Hot Water Connection  
Should the electricity supply cable be damaged, we  
recommend that you only contact authorised Technical  
Service Centres for the replacement.  
The water supply to the appliance can also be connected to  
the house's hot water line (centralised system, heating  
system), as long as it does not exceed a temperature of 60°  
C.  
The plug  
In this case, the wash cycle time will be shortened by about  
15 minutes and the wash efficiency slightly reduced.  
The connection must be made to the hot water line following  
the same procedures as those for the connection to the cold  
water line.  
The dishwasher plug must be accessible even when the  
appliance is installed as a built-in unit so that maintenance  
can be done safely.  
GB  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical Connection  
Electrical Connection  
As the colours of the wires in the mains lead may not  
correspond with the coloured markings identifying the  
terminal in your plug, proceed as follows:  
connect Green & Yellow wire to terminal market “E” or  
coloured Green or Green & Yellow.  
If your appliance is supplied with a 13 amp. fused plug it  
can be plugged into a 13 amp socket for immediate use.  
Before using the appliance please read the instruction below.  
WARNING: THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE CARRIED  
OUT BY A QUALIFIED ELECTRICIAN.  
Connect Brown wire to terminal marked “L” or coloured  
Red.  
Connect Blue wire to terminal marked “N” or coloured  
Black.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA approved  
fuse to BS 1362 should always be used, and the fuse cover  
re-fitted. If the fuse cover is lost, the plug must not be used  
until a replacement is obtained.  
If a 13 amp plug (BS 1363) is used it must be fitted with a  
13 amp fuse. A15 amp plug must be protected by a 15  
amp fuse, either in the plug or adaptor or at the  
distribution board.  
If you are in any doubt about the electrical supply to your  
machine, consult a qualified electrician before use.  
Replacemente fuse covers:  
If a replacement fuse cover is fitted, it must be of the correct  
colours as indicated by the coloured marking or the colour  
that is embossed in words on the base of the plug.  
Replacements can be obtained directly from your nearest  
Service Depot.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in accordance  
with the following code:  
Removing the plug:  
BLUE  
BROWN  
GREEN AND YELLOW  
“NEUTRAL(“N”)  
LIVE” (L)  
EARTH” (“E”)  
Ifyour appliance has a non-rewireable moulded plug and  
you should wish to remove it to re-route the mains cable  
through partitions, units etc., please esure that either:  
- the plug is replaced by a fused 13 amp re-wireable plug  
bearing the BSI mark of approval  
- or:  
GREEN &  
YELLOW  
- the mains cable is wired directly into a 13 amp cable outlet,  
controlled by a switch, (in compliance with BS 5733) which  
is accessible without moving the appliance.  
13 amp fuse  
BROWN  
BLUE  
Disposing of the plug:  
CROSS-BAR  
CORD GRIP  
Ensure that before disposing of the plug itself, you make  
the pins unusable so that it cannot be accidentally inserted  
into a socket.  
Instruction for connecting cable to an altenative plug:  
Important: the wires in the mains lead are coloured in  
accordance with the following code:  
Green & Yellow  
Blue  
Brown  
- Earth  
- Neutral  
- Live  
Disposing of the appliance:  
When disposing of the appliance please remove the plug  
by cutting the mains cable as close as possible to the plug  
body and dispose of it as described above  
CAUTION:  
The dishwasher plug must be accessible even when the  
appliance is installed as a built-in unit so that maintenance  
can be done safely.  
GB  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Merloni Elettrodomestici  
Viale Aristide Merloni 47  
60044 Fabriano  
Italy  
Tel +39 0732 6611  
Fax +39 0732 662501  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Jeep Motorized Toy Car 74383 User Manual
John Deere Automobile 772A User Manual
Joovy Stroller 350 User Manual
JVC Security Camera TK C700U User Manual
Kawasaki Drill 840517 User Manual
Kenmore Freezer 297310600 User Manual
Kensington Video Game Keyboard K39561 User Manual
Kenwood CD Player DP R6090 User Manual
Kenwood CD Player D R350 User Manual
King Canada Saw KC 514B C User Manual