Dishwasher
Instructions for installation and use
DE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Is a Good Habit to Get Into
NOTICE
6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.
Carefully read the instructions contained in this manual,
as they provide important information which is essential
to safe and proper installation, use and maintenance of
the appliance.
7.Do not touch the heating element during or after a wash
cycle.
This appliance complies w ith the follow ing
EEC directives:
8.Do not lean or sit on the door when it is open, as this
could overturn the dishwasher.
- 73/ 23/ EEC o f 19/ 02/ 73 (Lo w Vo lt a g e ) a n d
subsequent modifications;
- 89/ 336/ EEC o f 03/ 05/ 89 (Ele ct ro m a g n e t ic
Compatibility) and subsequent modifications.
9.If the appliance malfunctions, turn off water supply to
the appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "Troubleshooting." If you
cannot resolve the problem, contact a service centre.
10.Appliances which are no longer being used must be
made inoperable by cutting the power supply cord and
removing the door lock.
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that
the appliance is not damaged. If in doubt, contact a
qualified professional.
3.The dishwasher must only be used by adults for the
washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet
hands or feet;
To maintain the EFFICIENCY and SAFETY of this
appliance, w e recommend:
- We discourage the use of extension cords and multiple
sockets;
l call only the Service Centers authorized
by the manufacturer
l alw ays use original Spare Parts
- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the
power supply.
5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.
GB
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (control panel)
B
M
E
F
H
D
I
Intensive Normal
After
Delicates
Rapid
Hot rinse
Soak
dinner
25
1
5
70
55
55
50
45
Reset
2
4
7
3
6
A
C
N
G
L
Cycle phase underw ay indicator
Delayed start indicator light
ON-OFF Button
ON-OFF Indicator light
Door opening handle
Button for selection Upper or Low er Rack
Multifunction numeric indicator
Delayed start setting button
Low salt indicator light
Cycle selection knob
Racks indicators
M
N
Low rinse aid indicator light
GB
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (Interior)
E
G
F
H
J
I
K
L
Bottom Sprayer Arm
Upper Rack
Salt Container Cap
Washing Filter
Top Sprayer Arm
Rack Height Adjustor
Low er Rack
Detergent and Rinse Aid Dispenser
Technical characteristics
Width
cm. 60
Depth
cm. 60
cm. 85
Height
Capacity
12 standard place settings
20 KPa÷ 1MPa (0,2 ÷10 bar)
See data plate
Mains water pressure
Power voltage
Total absorber power
Fuse
See data plate
See data plate
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt ......
Salt
Adjusting Salt Consumption
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The dishwasher is designed to allow for adjusting the amount
of salt consumed based on the
harness of the water used. This
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
is intended to optimize and cus-
tomize the level of salt con-
sumption so that it remains at a
minimum.
Your Local Water Board can
Loading the Salt into
the Softener
supply the degree of hardness
Always use salt intended
of the water
for use with dishwashers.
in your area.
The salt container is
To adjust salt consumption, pro-
located beneath the lower
ceed as follows:
rack and should be filled
as follows:
1. Remove the lower rack
and then unscrew and
remove the cap from the
salt container;
2. If you are filling the
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti-
clockwise direction from the "_" setting towards the " +"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord-
ance with the following schema:
container for the first time, fill it with water;
3. Place the end of the funnel (supplied) into the hole and
introduce about 2 kg of salt. It is normal for a small amount
of water to come out of the salt container.
4. Carefully screw the cap back on.
Water Hardness
The salt container should be filled up w hen the low
salt indicator light "E" flashes on the LCD.
Salt
Autono-
consu-
Clarke
degrees
Selector
position
my
°dH
mmol/l
mption
(grams/-
cycle)
(cycles\2-
kg)
Warning: To prevent rust from forming, we advise you to
load the salt before starting a wash cycle.
0 ¸ 14
0 ¸ 17
0 ¸ 1,7
/
0
/
14¸ 36
18 ¸ 44 1,8 ¸ 4,4
"-"
20
40
60
60
40
25
36 ¸ 71 45 ¸ 89 4,5 ¸ 8,9
>71 > 89 > 8,9
MED
"+"
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and Rinse Aid ....
The rinse aid
Detergent
This product makes dishes sparkle more and it improves their
drying. The rinse aid container is situated on the inside of the
door; it should be filled up when the low rinse aid indicator
light "F" flashes on the LCD.
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the " Wash Cycle Table." The detergent dispenser is
located on the inside panel of the door.
Loading the Rinse Aid
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the "F" dose adjustor, located beneath
the " C" cap, with a screwdriver. There are 6 different
settings; the normal dosage setting is 4.
Loading the detergent
To open lid "A", press button "B". The cleaning detergent
should be introduced into the two containers "C"and "D"
up to the rim.
After pouring in the detergent, replace the lid, pressing
down until it clicks.
F
A
D
C
22 gr.
8
gr.
C
B
Important:
Dishwasher detergent in tablets is now available on the
market, in which case you should place one tablet into
container " D" and replace the lid.
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting. If
the dishes have white streaks, turn the dosage adjustor to a
lower setting.
Those Institutes which carry out comparative tests should
keep to the dosage indications contained in the wash cycle
table..
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Dishw asher
Top Rack
Bottom Rack
Before placing the dishes in the dishwasher, remove the
larger food particles to prevent the filter from becoming
clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they be allowed to
soak before they are washed. This will eliminate the need
for extra wash cycles.
Pull out the racks to facilitate loading the dishwasher.
How to Use the Low er Rack
We recommend that you place the most difficult to clean
items on the bottom rack: pots, pans, lids, serving dishes
and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the
sides of the racks in order to avoid blocking the rotation
of the top spray arm.
Load for 12 Standard Settings (for IEC- EN 50242 tests:
upper rack at top position)
Top Rack
Bottom Rack
- Pots, serving bowls, etc. must always be placed top
down.
- Deep pots should be
slanted to allow the water
to flow out.
- The bottom rack features
fold down tine rows (see
figure B) so that larger or
more pots and pans can be
Normal Daily Load
loaded.
fig. A
-The silverware basket can
be doubled (see figure A)
Fig. B
1
so that only one section may be used when the silver-
ware load is light. This also makes space for additional
pots and pans, and it can also be placed in the upper
rack.
2
- Silverware should be placed in the silverware basket
with the handles at the bottom; If the rack has side
baskets, the spoons should be loaded individually into
the appropriate slots. Especially long utensils should be
placed in the horizontal position at the front of the upper
rack.
fig. C
How to Use the Upper Rack
The upper rack is designed to hold more delicate and
lighter dishware, such as glasses, coffee and tea cups
and saucers, as well as plates, small bowls and shallow
pans (as long as they are not too dirty).
- Position the dishes and cookware so that they do not
get moved by the spray of water.
The upper rack can be adjusted for height by using the
knobs located on the sides of the rack itself (see figure
C).
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the Appliance
How to start a w ash cycle…
At the end of the w ash cycle….
After performing all the operations described in the previous
chapters, turn the water tap on completely, press ON-OFF
button "A" situated on the control panel, indicator light "B"
comes on.
The display turns on and the 3 dashes appear, indicating that
the dishwasher is awaiting instructions.
The end of the wash cycle is signalled by 2 beeps, and a
flashing "END" will come up on the display. Bring the selector
back to the RESET position, and the 3 dashes for
programming cancellation will appear.
Turn the appliance off by pressing the ON-OFF button, turn
off the water tap and open the door. Wait a few minutes
before removing the dishes: this way you won't have to
handle them while they're still hot and they will dry better.
Starting and setting the cycle.
Turn the cycle selector " M" until the reference notch on the
knob corresponds with the symbol or number of the cycle
you wish to set (consult the wash cycle table contained in
this manual, especially when first using the appliance).
After a few seconds, a beep indicates the wash cycle has
started and indicator " G" displays the phase with which it
has begun. The counter "L" will indicate the amount of time
left until the end of the wash cycle.
How to eliminate the drying phase.
To eliminate the drying phase from the wash cycle you wish
to start, just turn the knob to the Reset position then first
and foremost set any preferences as to:
Þ
Þ
upper or lower rack
delayed start
Cancelling or modifying a w ash cycle in progress…..
Premise: a wash cycle in progress can only be modified if it
hasn't been running for long.
Start the wash cycle by following the instructions. Symbol
relating to the drying phase will flash for approximately
4 seconds; immediately press button "I" and the symbol will
disappear, thus indicating that the drying phase has been
eliminated.
To modify a wash cycle in progress, turn knob " M" until it
reaches the RESET position.
After a few seconds, you will hear 4 beeps, indicator " G"
relating to the phase under way will come off and 3 dashes
will appear. At this point, all the settings will have been
cancelled.
To select a new wash cycle, repeat the instructions contained
in the paragraph entitled "Starting and setting the cycle"
If you have left out a dish…
You can interrupt a wash cycle by pressing the ON-OFF button,
then place the forgotten dishes into the appliance, which
will start up from where it was interrupted when you turn it
back on.
Cycle phase underw ay indicator
Your dishwasher is equipped with an indicator "G" comprising
4 symbols which represent the different phases of a wash
cycle. When the wash cycle has started, the display will indi-
cate the phases underway in sequence.
These phases are:
pre-wash,
wash, rinses, drying.
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dishw asher delayed start programming
Dishw asher delayed start programming
Premise: before selecting a wash cycle as indicated in the
paragraph entitled "Starting and setting a wash cycle…", a
delayed start can be set.
Press button "D" (see close-up view "control panel") to delay
the start of a wash cycle by 1 to 24 hours. Each time you
press the button, the counter "L" will display the number of
hours the cycle start has been delayed by in sequence; choose
the time you prefer.
Wash cycle modification buttons
Half load selection button on upper or low er rack.
This can be selected before setting any wash cycle, yet we
remind you that you should halve the amount of detergent
recommended for the wash cycle you have selected (see
wash cycle table).
Press button " I" and you will hear a beep, the indicator "N"
appears on the display: you can select which rack to perform
the half load on. Each time the button is pressed, you will
The delayed start indicator light " H" flashes and when the
appliance starts, the counter will begin the countdown to
the delayed start.
When this time is up, the wash cycle will begin and the
counter will now serve to display the amount of time left
until the end of the wash cycle.
hear a beep, and symbol
appears indicating the wash
indicates the wash
on the upper rack, whereas symbol
on the lower rack. Press the button again and you will hear
another beep, thereby resetting the selection and the
appliance will consequently wash on both racks.
To use the racks correctly, we recommend you read the
chapter entitled "Loading the dishes".
NOTE:
n
it is best if you keep from modifying anything during
countdown; if this is absolutely necessary, then turn the knob
to the RESET position: 4 beeps and the 3 dashes appearing
indicate that all settings have been cancelled
Repeat the operations for " dishwasher delayed start
programming" and for "starting and setting the wash cycle"
following the instructions in the relative paragraphs.
n
Should there be a power failure or should the door of
the appliance be opened during the countdown, the latter
will come to a stop and will re-start either when the power
comes back on or when the door is closed.
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
Detergent
for pre-w ash
+ w ash
Rinse Aid
Cycle
Cycle selection
instructions
Cycle description
Pre-wash with cold water
Pre-wash with hot water at 45°C.
Extended wash at 70°C.
1 rinse with cold water.
Hot rinse at 70°C.
Very dirty dishes and
pans (not to be used
for delicate items).
8+22 g.
*
1) Intensiv
Drying.
2 pre-washes with cold water.
Extended wash at 55°C.
Hot rinse at 70°C.
Drying.
Normally dirty pans
and dishes. Standard
daily cycle.
2) Normal
(IEC-EN 50242)
8+22 g.
8+22 g.
*
*
2 Pre-washes with cold water.
Wash at 55°C.
Hot rinse at 70°C.
Drying.
Normally dirty pans
and dishes with no
dry residue.
3) After Dinner
Economic and fast
cycle to be used for
more delicate items
which are sensitive to
high temperatures.
Run cycle
Wash at 50°C.
Lukewarm rinse.
Hot rinse at 70°C.
Drying.
22 g.
*
immediately after
use.
4) Delicates
Economic and fast
cycle to be used for
slightly dirty dishes.
Run cycle
immediately after
use. No drying.
Short wash at 45°C.
Cold rinse.
22 g.
5) Rapid 25’
6) Hot Rinse
To be used for dishes
that only need to be
rinsed.
Hot rinse at 70°C.
Drying.
*
Preliminary wash
cycle for dishes and
pans awaiting
completion of the
load with the dishes
from the next meal.
Short cold wash to prevent food
from drying onto the dishes.
7) Soak
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. In order to prevent odors
from forming and food from caking onto the dishes, you
can run the hold cycle.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.
How to Keep Your Dishw asher in Shape
After Every Wash
When You Go on Holiday
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
Moving the Appliance
No Solvents or Abrasive Cleaning Products
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
To clean the exterior and rubber parts of the dishwasher, do
not use solvents or abrasive cleaning products. Rather, use
only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
Seals
One of the factors that cause odors to form in the dishwasher
is food that remains trapped in the seals. Periodic cleaning
with a damp sponge will prevent this from occuring.
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must
positioning in its seat and
pressing downward.
be cleaned .
The dishwasher must
never be used without the
The filter efficiently removes food particles from the wash
A
B
water, allowing it
to be recirculated
during the cycle.
For this reason, it
is a good idea to
filters.
Improper
replacement of the filters
may reduce the perfor-
mance level of the
appliance and damage
dishes and utensils.
remove
larger
the
food
Cleaning the Sprayer
Arms
particles trapped
in the filter after
each wash cycle
by rinsing the
It may happen that food particle become encrusted on the
sprayer arms and block the holes (see " Close up view
(interior)" , letters F-I). Check the sprayer arms periodically
and clean them when needed.
" A" semi-circular filter and cup under running water. To
remove the filter assembly, pull on the cup handle in the
upward direction. The entire filter assembly (made up of
the "A" semicircular filter and the " B" fine filter) should be
cleaned at least once a month.
To clean the filter and the fine filter, use a cleaning brush.
Then, reassemble the filter parts as shown in the figures
below and reinsert the entire assembly in the dishwasher,
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter (see figure 2 under
"Installation") located on the outlet of the water supply tap.
After turning off the water tap, unscrew the end of the water
supply hose, remove the filter and clean it carefully under
running water. Then, return the filter to its place and tighten
the water supply hose back into position.
Troubleshooting
It may occur that the dishwasher does not function or does
not function properly. Before calling for assistance, let us
see what can be done first.
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
The Dishw asher Does Not Start
Have you checked whether:
Error messages
The dishwasher is equipped with a safety system which is
able to detect any operating anomalies. These anomalies
are signalled by some messages flashing on the counter. When
H2O is flashing, you should cancel the wash cycle as described
in the paragraph entitled “Cancelling or modifying a wash
cycle in progress”, then check whether there is any water in
the mains supply and that the water tap has been turned on.
Restart the appliance following the instructions provided and
if the message persists, then call for Technical Assistance. In
all other cases, remember the message which is flashing on
the counter, turn the appliance off and call for technical
assistance, stating which message was flashing.
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on " ON" ;
- the water supply is turned on.
The Dishw asher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you put the right amount of detergent into the
dispenser?
Is the wash cycle suitable for the dishes you have placed
inside the appliance?
Are the filter and microfilter clean?
Can the sprayer arms turn freely?
The Dishw asher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
If, despite all these checks, the dishwasher still does not
function and/or the problem persists, contact the nearest
authorised service centre and provide them with the
following information:
- the nature of the problem;
- the model type number (Mod. ...) and the serial number
(S/N ....), which are indicated on the plate located on the
side of the inner part of the door.
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Appliance
Drain Hose Connection
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned to
the right or the left to facilitate proper installation.
Insert the drain hose into a
drain pipe with a minimum
diameter of 4 cm., or let it run
into the sink, making sure to
avoid bending or crimping it.
Use the speical plastic support
that comes with the appliance
(see figure to the right). The
free end of the hose must be
at a height between 40 and
100 cm.and must not be
immersed in water.
A
This dishwasher model can be built-in under the one worktop,
and it therefore comes provided with an assembly kit com-
plete with an instructions sheet.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher, making
it level. In any case, the appliance should not be inclined
more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.
Attention: The special plastic hose support must be solidly
fastened to the wall to prevent the drain hose from moving
and allowing water to spill outside the drain.
Electrical Connection
Cold Water Connection
After making sure that the voltage and frequency values for
the current in the home correspond to those on the rating
plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
Connect the cold water supply hose to a threaded 3/4 (gas)
connector, inserting the small
filter supplied with the
dishwasher and making sure
that it is fastened tightly in
place (see figure 2).
If the water pipes are new or
have not been used for an
extended period of time, let the
water run to make sure that
the water is clear and free of
impurities. If this precaution is
not taken, there is a risk that
A
Fig.2
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical
Service Centres for the replacement.
the water inlet can get blocked and damage the appliance.
Hot Water Connection
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of 60°
C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
GB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
Electrical Connection
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction below.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT
BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colours as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
BLUE
BROWN
GREEN AND YELLOW
“NEUTRAL” (“N”)
“LIVE” (“L”)
“EARTH” (“E”)
Removing the plug:
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 amp fuse
BROWN
BLUE
Disposing of the plug:
CROSS-BAR
CORD GRIP
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above
CAUTION:
The dishwasher plug must be accessible even when the
appliance is installed as a built-in unit so that maintenance
can be done safely.
GB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel +39 0732 6611
Fax +39 0732 662501
Download from Www.Somanuals.com. All Manuals Search And Download.
|