Dishwasher
Instructions for installation and use
D 61
Download from Www.Somanuals.com. All Manuals Search And Download.
D 61
Dishwasher
Installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Is a Good Habit to Get Into
NOTICE
- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the power
supply.
5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash
cycle.
Carefully read the instructions contained in this manual, as
they provide important information which is essential to safe
and proper installation, use and maintenance of the
appliance.
This appliance complies w ith the follow ing EEC
directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)
and subsequent modifications.
8.Do not lean or sit on the door when it is open, as this
could overturn the dishwasher.
9.If the appliance malfunctions, turn off water supply to the
appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "Troubleshooting." If you
cannot resolve the problem, contact a service centre.
10.Appliances which are no longer being used must be
made inoperable by cutting the power supply cord and
removing the door lock.
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that the
appliance is not damaged. If in doubt, contact a qualified
professional.
3.The dishwasher must only be used by adults for the washing
of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet
hands or feet;
- We discourage the use of extension cords and multiple
sockets;
- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
To maintain the EFFICIENCY and SAFETY of this
appliance, w e recommend:
l call only the Service Centers authorized
by the manufacturer
l alw ays use original Spare Parts
Close-up View (control panel)
D
B
1
2
3
4
A
C
Handle For Opening Door
Knob For Selecting Cycles
ON - OFF Button
ON - OFF Light
GB
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (Interior)
E
G
F
H
J
I
K
L
Upper Rack
Bottom Sprayer Arm
Salt Container Cap
Washing Filter
Top Sprayer Arm
Rack Height Adjustor
Low er Rack
Detergent and Rinse Aid Dispenser
Technical characteristics
Width
cm. 60
Depth
cm. 60
cm. 85
Height
Capacity
12 standard place settings
20 KPa÷ 1MPa (0,2 ÷10 bar)
See data plate
Mains water pressure
Power voltage
Total absorber power
Fuse
See data plate
See data plate
GB
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt ......
Salt
Adjusting Salt Consumption
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The dishwasher is designed to
allow for adjusting the amount
of salt consumed based on the
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
harness of the water used. This
is intended to optimize and cus-
tomize the level of salt consump-
tion so that it remains at a mini-
mum.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and
should be filled as follows:
Your Local Water Board can
supply the degree of hardness of
the water
1. Remove the lower rack and then unscrew and remove
the cap from the salt container;
2. If you are filling the container for the first time, fill it with
water;
3. Place the end of the funnel (supplied) into the hole and
introduce about 2 kg of salt. It is normal for a small amount
of water to come out of the salt container.
4. Carefully screw the cap back on.
in your area.
To adjust salt consumption, proceed as follows:
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti-
clockwise direction from the "_" setting towards the " +"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord-
ance with the following schema:
Water Hardness
Salt
Autono-
consu-
Clarke
degrees
Selector
position
my
°dH
mmol/l
mption
(grams/-
cycle)
(cycles\2-
kg)
0 ¸ 14
0 ¸ 17
0 ¸ 1,7
/
0
/
14¸ 36
18 ¸ 44 1,8 ¸ 4,4
"-"
20
40
60
60
40
25
The salt container should be filled after about every
30 w ash cycles.
36 ¸ 71 45 ¸ 89 4,5 ¸ 8,9
>71 > 89 > 8,9
MED
"+"
Warning: To prevent rust from forming , we advise you to
load the salt before beginning a wash cycle.
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and Rinse Aid ....
Rinse Aid
Detergent
This product makes dishes sparkle and helps them to dry
without spotting. The dispenser is located on the inside panel
of the door and should be filled after every 80 wash cycles
(or when the rinse aid indicator light comes on for those
models with this feature).
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the " Wash Cycle Table." The detergent dispenser is
located on the inside panel of the door.
Loading the Rinse Aid
Loading the detergent
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the "F" dose adjustor, located beneath
the " C" cap, with a screwdriver. There are 6 different
settings; the normal dosage setting is 4.
To open lid "A", press button "B". The cleaning detergent
should be introduced into the two containers "C"and "D"
up to the rim.
After pouring in the detergent, replace the lid, pressing
down until it clicks.
A
F
D
C
22 gr.
8
gr.
C
B
Important:
Dishwasher detergent in tablets is now available on the
market, in which case you should place one tablet into
container "D" and replace the lid.
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting. If
the dishes have white streaks, turn the dosage adjustor to a
lower setting.
Those Institutes which carry out comparative tests should
keep to the dosage indications contained in the wash cycle
table.
Notice: To facilitate closing the cover, remove any
excess detergent on the edges of the dispenser.
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Dishw asher
Before placing the dishes in the dishwasher, remove the
larger food particles to prevent the filter from becoming
clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they be allowed to
soak before they are washed. This will eliminate the need
for extra wash cycles.
Upper Rack
Bottom Rack
Pull out the racks to facilitate loading the dishwasher.
How to Use the Low er Rack
We recommend that you place the most difficult to clean
items on the bottom rack: pots, pans, lids, serving dishes
and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the
sides of the racks in order to avoid blocking the rotation
of the top spray arm.
Load for 12 Standard Settings (For IEC- EN 50242: upper
rack at top position)
Upper Rack
Bottom Rack
- Pots, serving bowls, etc. must always be placed top
down.
- Deep pots should be slanted to allow the water to flow
out.
- Silverware should be placed in the silverware basket
with the handles at the bottom; If the rack has side
baskets, the spoons should be loaded individually into
the appropriate slots. Especially long utensils should be
placed in the horizontal position at the front of the upper
rack.
Normal Daily Load
How to Use the Upper Rack
The upper rack is designed to hold more delicate and
lighter dishware, such as glasses, coffee and tea cups
and saucers, as well as plates, small bowls and shallow
pans (as long as they are not too dirty).
- Position the dishes and cookware so that they do not
get moved by the spray of water.
1
2
4
How to adjust the Upper rack ...
The top rack can be adjusted using the two rack heights
(top and bottom). To adjust the rack, open up the tabs
that lock the guides and pull out the rack. Arrange the
rack with the back wheels in either the top or bottom
position and then insert it along the guides until the front
wheels are on as well. Close the tabs to lock the rack in
place (see Fig. F)
3
Fig. F
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the Appliance
Starting a w ash cycle....
1. Make sure that the plug for the appliance is inserted into
the wall socket.
2. Make sure that the water supply is turned on to full
pressure.
Press the ON-OFF button, and the ON light will turn off. Rota-
te the knob in the clockwise direction to the desired cycle
setting (see the section entitled, "Starting a wash cycle...").
Then, turn the dishwasher back on using the ON-OFF button.
3. Load the dishwasher (see the section entitled, "Loading
the Dishwasher").
4. Pour in the detergent (see the section entitled, "Salt,
Detergent and Rinse Aid").
If you forget to load some of the dishes...
The wash cycle can be interrupted by pressing the ON-OFF
button. You can then load additional dishes and turn the
appliance back on. The cycle will start where it left off.
5. Turn the knob located on the right of the control panel in
the clockwise direction until the number or symbol for the
cycle setting is aligned with the reference mark (see the
section entitled, "Wash Cycle Table").
6. Press the ON-OFF botton, and the ON-OFF light will turn
on. At this point, the wash cycle will begin.
At the end of the w ash cycle...
When the knob stops turning and is aligned with a STOP
mark (see figure), the cycle has finished. Turn off the
appliance using the ON-OFF button, turn off the water supply
and open the door of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid
handling the dishes and utensils while they are still hot and
more susceptible to breakage. They will also dry better.
Cancelling or modifying a w ash cycle setting...
Premise: A cycle that is underway can only be modified if it has
only been running for a short time. Otherwise, the detergent may
have already been used, and the appliance may have already drained
the wash water. If this is the case, the detergent dispenser must be
refilled (see the paragraph entitled, "Loading the Detergent").
STOP
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
Detergent
for
Pre-w ash
+ Wash
Rinse Aid
Cycle
Cycle
Selection
Information
Description of Cycle
Very dirty dishes,
pots and pans
(not to be used
with delicate
items).
Pre-wash with hot water
Pre-wash with cold water
Extended wash at 65°C.
Rinse with hot water at 70°C.
Drying.
1) Heavy Duty
8+22 gr.
8+22 gr.
*
*
Normally dirty
dishes, pots and
pans. Standard
daily cycle.
2 pre-washes with cold water.
Extended wash a 65°C.
Rinse with hot water at 70°C.
Drying.
2) Normal Wash
(IEC-EN 50242)
Economic, fast
cycle to be used
to on not very
dirty dishes right
after they are
used. No drying
cycle.
Short wash at 65°C.
Cold rinse.
3) Rapid Wash
22 gr.
Pre-wash of
dishes, pots and
pans while
waiting for the
load to be
Short cold wash to prevent food
residue from drying on the dishes.
4) Soak
completed after
the subsequent
meal.
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. In order to prevent odors
from forming and food from caking onto the dishes, you
can run the hold cycle.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.
How to Keep Your Dishw asher in Shape
When You Go on Holiday
After Every Wash
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do
not use solvents or abrasive cleaning products. Rather, use
only a cloth and warm soapy water.
Seals
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
One of the factors that cause odors to form in the dishwasher
is food that remains trapped in the seals. Periodic cleaning
with a damp sponge will prevent this from occuring.
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must
be cleaned frequently.
The filter efficiently removes food particles from the wash
water, allowing it to be recirculated during the cycle. For
this reason, it is a good
The dishwasher must never
be used without the filters.
Improper replacement of
the filters may reduce the
performance level of the
appliance and damage
dishes and utensils.
A
B
idea to remove the
larger food particles
trapped in the filter after
each wash cycle by
rinsing the " A" semi-
circular filter and cup
under running water. To
Cleaning the Sprayer Arms
remove the filter
assembly, pull on the
It may happen that food particles become encrusted on the
sprayer arms and block the holes. Check the sprayer arms
periodically and clean them when needed (see “Close-up
View [interior]”, letters F-I).
cup handle in the upward direction. The entire filter assembly
(made up of the "A" semicircular filter and the "B" fine
filter) should be cleaned at least once a week.
To clean the filter and the fine filter, use a cleaning brush.
Then, reassemble the filter parts as shown in the figures
below and reinsert the entire assembly in the dishwasher,
positioning in its seat and pressing downward.
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter (see figure 2 under
"Installation") located on the outlet of the water supply tap.
After turning off the water tap, unscrew the end of the water
supply hose, remove the filter and clean it carefully under
running water. Then, return the filter to its place and tighten
the water supply hose back into position.
Troubleshooting
inside the appliance?
Are the filter and microfilter clean?
Can the sprayer arms turn freely?
It may occur that the dishwasher does not function or does
not function properly. Before calling for assistance, let us
see what can be done first: have you forgot to press one of
the buttons or to perform an essential operation?
The Dishw asher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
The Dishw asher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on " ON" ;
- the water supply is turned on.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
If, despite all these checks, the dishwasher still does not
function and/or the problem persists, contact the nearest
authorised service centre and provide them with the
following information:
The Dishw asher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the nature of the problem;
- the model type number (Mod. ...) and the serial number
(S/N ....), which are indicated on the plate located on the
side of the inner part of the door.
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you put the right amount of detergent into the
dispenser?
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
Is the wash cycle suitable for the dishes you have placed
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Drain Hose Connection
Positioning the Appliance
Insert the drain hose into a drain
pipe with a minimum diameter
of 4 cm., or let it run into the
sink, making sure to avoid
bending or crimping it. Use the
speical plastic support that
comes with the appliance (see
figure to the right). The free end
of the hose must be at a height
between 40 and 100 cm and
must not be immersed in water.
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned to
the right or the left to facilitate proper installation.
A
This dishwasher model can be built-in under the one worktop,
and it therefore comes provided with an assembly kit com-
plete with an instructions sheet.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher, making
it level. In any case, the appliance should not be inclined
more than 2°.
Attention: The special plastic hose support must be solidly
fastened to the wall to prevent the drain hose from moving
and allowing water to spill outside the drain.
If the appliance is level, it will help ensure proper perfor-
mance.
Electrical Connection
After making sure that the voltage and frequency values for
the current in the home correspond to those on the rating
plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas)
connector, inserting the small
filter supplied with the
dishwasher and making sure
that it is fastened tightly in place
(see figure 2).
If the water pipes are new or
have not been used for an
extended period of time, let the
water run to make sure that the
water is clear and free of
impurities. If this precaution is
A
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical Service
Centres for the replacement.
Fig.2
not taken, there is a risk that the water inlet can get blocked
and damage the appliance.
Hot Water Connection
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of 60°
C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E”or
coloured Green or Green & Yellow.
Electrical Connection
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction below.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT
BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colours as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
BLUE
BROWN
GREEN AND YELLOW
“NEUTRAL” (“N”)
“LIVE” (“L”)
“EARTH” (“E”)
Removing the plug:
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 amp fuse
BROWN
BLUE
Disposing of the plug:
CROSS-BAR
CORD GRIP
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above
CAUTION:
The dishwasher plug must be accessible even when the
appliance is installed as a built-in unit so that maintenance
can be done safely.
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel +39 0732 6611
Fax +39 0732 662501
Download from Www.Somanuals.com. All Manuals Search And Download.
|