ScreenPlay 7210
User’s Guide
[ English • Français • Deutsch • Español • Italiano • Norsk • Nederlands ]
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Warning
ENGLISH
Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conform to the following
directives and norms:
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Declaration of Conformity
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
--Reorient or relocate the receiving antenna.
EN 55024
EN 61000-3-2
EN 61000-3-3
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
--Consult the dealer or an experienced radio/TV technician for help.
February, 2004
Changes or modifications not expressly approved by InFocus Corporation can void
the user's authority to operate the equipment.
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Digital Light Processing is a trademark or reg-
istered trademark of Texas Instruments. Faroudja, DCDi, and TrueLife are trade-
marks or registered trademarks of Faroudja. InFocus and ScreenPlay are trademarks
or registered trademarks of InFocus Corporation.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, CUL, NOM, IRAM, GOST, C-tick
Other specific Country Approvals may apply. Please see product certification label.
InFocus reserves the right to alter product offerings and specifications at any time
without notice.
Ver. 12-04
1
Download from Www.Somanuals.com. All Manuals Search And Download.
For complete details on connecting and operating the projector, refer to this
User’s Guide. Electronic versions of this User’s Guide in multiple languages
Table of Contents
Introduction
4
6
The website also has technical specifications (an interactive image size cal-
culator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration.
Positioning the projector
Video connections
7
Connecting a video device
Displaying a video image
Connecting a computer
Shutting down the projector
Troubleshooting your setup
Using the keypad buttons
Using the remote control
Optimizing video images
Customizing the projector
Using the menus
8
9
11
12
12
20
21
22
22
23
24
29
31
31
32
34
34
34
35
36
37
Picture menu
Settings menu
Maintenance
Cleaning the lens
Replacing the projection lamp
Appendix
Red LED behavior and projector errors
Projected image size
Source compatibility
Projector dimensions for ceiling mount installations
RS-232 terminal specifications
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Operating Considerations
Do not place objects in the areas along the side and in the front of the projector
•
Place the projector in a horizontal position no greater than 15 degrees
off axis. See “Positioning the projector” on page 6.
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
2 ft (.6m)
2 ft (.6m)
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
•
•
Use only InFocus-approved ceiling mounts.
Use only the power cord provided. A surge-protected power strip is
recommended.
2 ft (.6m)
•
•
Refer to this manual for proper startup and shutdown procedures.
In the unlikely event of the lamp rupturing, discard any edible items
placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
the ruptured lamp. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or
federal ordinances and regulations. For more information see
Do not place objects or people in the 2 foot (.6m) area along the front of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the warranty section at
the end of this User's Guide.
5 ft (1.5m)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector components and features
Introduction
keypad
Congratulations and thank you for your excellent choice of a superior digi-
tal image projection device. Your new ScreenPlay™ 7210 projector from
remote
control
receiver (IR)
®
InFocus is specifically designed for home cinema applications. The
ScreenPlay 7210 sets the standard for high-definition digital perfection, fea-
turing true High Definition 1280x720 resolution using the latest DLP™ tech-
nology and new DCDi video processing from Faroudja™. Calibrated to D65
color mastering standards, the ScreenPlay 7210 reproduces colors and
details the way the director intended. Whether you are watching movies or
High Definition broadcasts or playing the latest video game, you will enjoy
breathtaking image quality.
IR
air intake
vent
elevator foot release
threaded
focus
ring
zoom
The focus ring is threaded, similar to a camera lens, for adding external
optical filters to customize your viewing experience. The thread is made to
accommodate some standard 72mm SLR-type filters.
heat vent
I/O panel
Product specifications
To read the latest specifications on your digital image projector, be sure to
visit our website, as specifications are subject to change. Web address infor-
mation is located on the inside back cover of this User’s Guide.
IR
remote control
receiver (IR)
Accessories
The standard accessories that came with your projector can be found on the
included packing list. Optional accessories are listed in the Accessories cata-
log that came with the projector and can also found on our website. See the
inside back cover for the Web address.
exhaust
leveling
foot
Online Registration
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside back cover for
the Web address.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Panel
The projector provides eight discreet video connectors:
remote control
receiver (IR)
IR input
D5
video
video/computer
1 & 2
video
•
•
•
•
•
•
two red-green-blue RCA (SD/ED/HD component)
two S-video
12v triggers
s-video
1
Y
Y
one composite RCA
IR in
2
trigger 1
trigger 2
8
1
D5
M1-DA
vesa
2
Pb
Pr
Pb
Pr
7
video
one M1-DA (HD, RGBHV, HD component, DVI, and computer)
one VESA (HD, RGBHV, HD component, and computer)
one D5 (SD/ED/HD component, RGB SCART)
4
serial control
5
s-video
6
component
3
component
It also has a mini-jack input for a Niles or Xantech-compatible IR repeater
and an RS-232 connector for serial control. The Command Line Interface
(CLI) specifications and commands are listed in the Appendix starting on
page 37.
power
connector
component
video
serial
connector
lock
Two 3.5mm mini-jack triggers provide 12 volt current. Trigger 1 provides a
constant output while the projector is on. For example, if you connect your
projection screen to Trigger 1, when you turn on the projector the screen will
move down; when you turn the projector off, the screen will return to the
storage position. Trigger 2 provides a 4:3 aspect trigger. When you select 4:3
in the Aspect Ratio menu or from the Resize button on the remote, a 12v
signal will be sent after a five second delay. Use this trigger for screens with
4:3 aspect curtains. When you switch back to 16:9 format, the curtains open
to reveal the entire screen.
+12v
ground
3.5mm mono plug for
12 volt current
connection
For details on each connector type and their inputs, see page 35.
to screen relay (see screen manufacturer
for details)
.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning the projector
There are a number of factors to consider when determining where to set up
the projector, including the size and shape of your screen, the location of
your power outlets, and the distance between the projector and the rest of
your equipment. Here are some general guidelines.
1 Position the projector on a flat surface at a right angle to the screen.
The projector must be within 10 feet (3 m) of your power source. To
ensure adequate cable access, place the projector at least 6 inches
(0.15m) from a wall or other objects. Place the projector at least 5.6 feet
(1.7 m) from the projection screen.
If you install the projector on the ceiling, refer to the installation guide
that comes with the Ceiling Mount Kit for more information. To turn
the image upside down, see page 29. InFocus recommends use of an
authorized InFocus ceiling mount. The Ceiling Mount Kit is sold sepa-
rately.
10’ high
image
2 Position the projector the desired distance from the screen.
The distance from the lens of the projector to the screen, the zoom set-
ting, and the video format determine the size of the projected image.
For more information about projected image sizes, see page 34.
The image exits the projector at a given angle. This image offset is 116%.
This means that if you have an image 10’ high, the bottom of the image will
be 1.6’ above the center of the lens.
bottom of image
1.6’ above lens
lens center
tor.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1: Video connections
Video connections
You can connect VCRs, DVD players, camcorders, digital cameras, video
games, HDTV receivers, and TV tuners to the projector. (You cannot directly
connect the coaxial cable that enters your house from a cable or satellite
company; the signal must pass through a tuner first. Examples of tuners are
digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.
Basically, any device that can change channels is considered a tuner.) Audio
must be provided by your own speakers, as the projector has no separate
audio controls. If there is more than one output, select the highest quality
one. DVI, Component video and RGB (M1, HD15) have the best quality, fol-
lowed by S-video, and then composite video.
Video Game
VESA
Composite video
S-video
VESA 2
Video 7
S-video 4, 5
Component 3, 6
Component video
video
M1-DA
VESA
s-video
1
Y
Y
IR in
2
trigger 1
8
1
D5
M1-DA
vesa
2
Pb
Pr
Pb
Pr
7
video
Table 1: Video connections
trigger 2
4
serial control
5
s-video
6
component
3
component
Connector label
Input signal
Connector
on projector
Standard Broadcast TV (not
HDTV), via cable, digital
cable, satellite TV, DirectTV
Component video
S-video
Composite video
Component 3, 6
S-video 4, 5
Video 7
component
video
For a complete list of compatible sources, see page 35 of the Appendix.
HDTV
Component video
VESA
DVI
Component 3, 6
VESA 2
M1-DA 1
DVD
Component video
S-video
Composite video
Component 3, 6
S-video 4, 5
Video 7
VCR
Composite video
S-video
Component video
Video 7
S-video 4, 5
Component 3, 6
Video Camera
Composite video
S-video
Video 7
S-video 4, 5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a video device
If your video device has more than one output, select the highest quality
one. DVI video has the best quality, followed by Component video, S-video,
and then composite video.
If the video device uses component cable connectors, plug the cable’s green
connectors into the green component-out connector on the video device and
into the green component connector (labeled “Y”) on the projector. Plug the
component cable’s blue connectors into the blue component-out connector
on the video device and into the blue component connector (labeled “Pb”)
on the projector. Plug the component cable’s red connectors into the red
component-out connector on the video device and into the red component
connector (labeled “Pr”) on the projector.
1
2
Y
Y
connect component cable
connect S-video cable
IR in
M1-DA
1
D5
8
trigger
trigger
1
2
vesa
2
Pb
Pr
Pb
Pr
7
video
4
serial control
5
s-video
6
component
3
component
1
2
Y
Y
I
R
i
n
trigger
trigger
1
2
M1-DA
1
D5
8
vesa
2
Pb
Pr
Pb
Pr
7
video
4
5
serial control
s-video
6
component
3
component
If the video device uses a round, four-prong S-video connector, plug an
S-video cable into the S-video connector on the video device and into the S-
video connector on the projector.
connect composite video cable
1
2
Y
Y
I
R
i
n
M1-DA
1
D5
8
trigger
trigger
1
2
vesa
2
Pb
Pr
Pb
Pr
7
video
4
5
serial control
s-video
3
component
6
component
If the video device uses a yellow composite video connector, plug a compos-
ite video cable’s yellow connector into the video-out connector on the video
device. Plug the other yellow connector into the yellow Video connector on
the projector.
1
2
Y
Y
connect M1-D cable
connect VESA cable
I
R
i
n
M1-DA
1
D5
8
trigger
trigger
1
vesa
2
Pb
Pr
Pb
Pr
7
video
2
4
serial control
5
s-video
3
component
6
component
If the video device uses a DVI connector, plug an M1-D cable into the video-
out connector on the video device. Plug the other connector into the M1-DA
connector on the projector.
1
2
Y
Y
If the video device uses a VESA connector, plug a VESA cable into the
video-out connector on the video device. Plug the other connector into the
VESA connector on the projector.
I
R
i
n
M1-DA
1
D5
8
trigger
trigger
1
2
vesa
2
Pb
Pr
Pb
Pr
7
video
4
ser
5
s-video
3
component
6
component
1
2
Y
Y
I
R
i
n
Connecting the power cable
M1-DA
1
D5
8
trigger
1
2
vesa
2
Pb
Pr
Pb
Pr
7
video
trigger
4
5
serial control
s-video
3
component
6
component
connect power cable
Connect the power cable to the connector on the back of the projector and to
your electrical outlet. The Power LED on the keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying a video image
Remove the lens cap.
remove lens cap
press Power
Press the Power button on the top of the projector.
The projector chimes if the chime feature is enabled (page 30). The LED
flashes green and the fans start to run. When the lamp comes on, the startup
screen displays and the LED is steady green. It can take a minute for the
image to achieve full brightness.
? No startup screen? Get help on page 12.
Plug in and turn on the video device.
turn on video device
An image from the video device should appear on the projection screen. If it
doesn’t, press the Source button on the keypad.
Adjust the height of the projector by pressing the release button to extend
the elevator foot. Rotate the leveling foot, if necessary.
adjust height
rotate
leveling
foot
elevator
foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 34 for a table listing screen projected image
sizes and distances to the screen.
adjust distance
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the zoom or focus rings by rotating them until the desired image size
and sharpness are produced.
adjust zoom and focus
zoom
focus
If the image is not square, adjust the keystone using the buttons on the key-
pad. Press the upper Keystone button to reduce the width of the upper por-
tion of the image, and press the lower Keystone button to reduce the width
of the lower portion.
adjust keystone
You can also adjust the horizontal and vertical keystone via the Picture
menu. See page 24
The Contrast, Brightness, Color, and Tint are factory calibrated to D65 col-
ors, but you can adjust these settings in the Picture menu if necessary.
adjust Picture menu
See page 23 for help with the menus.
add a lens filter
The focus ring is threaded, similar to a 35mm camera lens. To put a filter on
your lens, simply screw it clockwise onto the threaded focus ring.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a computer
connect computer cable
1
2
Y
Y
I
R
i
n
trigger
trigger
1
2
M1-DA
1
D5
8
vesa
2
Pb
Pr
Pb
Pr
7
video
4
se
5
s-video
6
component
3
component
Connect either a VESA cable or M1 cable into the appropriate connector on
the projector. Connect the other end to the video port on your computer. If
you are using a desktop computer, you first need to disconnect the monitor
cable from the computer’s video port.
1
2
Y
Y
I
R
i
n
M1-DA
1
D5
8
trigger
trigger
1
2
vesa
2
Pb
Pr
Pb
Pr
7
video
4
5
serial control
s-video
3
component
6
component
1
2
Y
Y
Connect the power cable to the connector on the back of the projector and to
your electrical outlet.
IR in
M1-DA
1
D5
8
trigger
1
2
vesa
2
Pb
Pr
Pb
Pr
7
video
connect power cable
trigger
4
serial control
5
s-video
6
component
3
component
The Power LED on the projector’s keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector.
Turn on the projector, then your computer.
You can control the projector from an LCD control panel or computer by
connecting an RS-232 cable to the projector’s Serial connector. Specific
RS-232 commands can be found in the Appendix starting on page 38 and in
the Service and Support section of our website at www.infocushome.com/
support.
connect RS-232 cable
1
2
Y
Y
I
R
i
n
M1-DA
1
D5
8
trigger
1
2
vesa
2
Pb
Pr
Pb
Pr
7
video
trigger
4
serial control
5
s-video
6
component
3
component
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutting down the projector
Troubleshooting your setup
Power Save
If your image appears correctly on the screen, skip to the next section
(page 20). If it does not, troubleshoot the setup.
The projector has a Power Save feature in the System menu that automati-
cally turns the lamp off after no signals are detected for 20 minutes. After 10
additional minutes with no signal, the projector powers down. If an active
signal is received before the projector powers down, the image is displayed.
You must press the Power button to display an image after 30 minutes have
passed.
The LED on top of the projector’s keypad indicates the state of the projector
and can help you troubleshoot.
Table 2: LED behavior and meaning
Turning off the projector
LED color/behavior
Meaning
To turn off the projector, press the Power button. The lamp turns off and the
LED blinks green for about one minute while the fans continue to run to
cool the lamp. When the lamp has cooled, the LED lights green and the fans
stop. Unplug the power cable to completely power off the projector.
solid green
The projector is plugged in, or the projec-
tor has been turned on and the software
has initialized. The projector has been
turned off and the fans have stopped.
blinking green
The Power button has been pressed and
the software is initializing, or the projec-
tor is powering down and the fans are
running to cool the lamp.
blinking red
The projector will not start up if the LED
A fan (blinks 4 times) or lamp (blinks 3
times) failure has occurred. Turn off the
is blinking red. You must correct the prob- projector and wait one minute, then turn
lem, disconnect and reconnect the power
cable, then power on the projector.
the projector on again. Also check for a
blocked vent or a stopped fan (blinks 5
times).
See page 34 for more information on
blinking red LEDs.
solid red
An unidentifiable error: please contact
Technical Support.
The following table shows some potential problems. In some cases, more
than one possible solution is provided. Try the solutions in the order they
are presented. When the problem is solved, you can skip the additional
solutions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Solution
Result
Plug power cable in and remove lens cap
press Power button
No startup screen
Correct image
ScreenPlay
Correct image
Move projector, adjust zoom, adjust height
Image not centered on screen
zoom
Adjust horizontal or vertical position in
Picture>Keystone menu
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust keystone on keypad or Keystone
menu
Square image
Image not square
Change aspect ratio to 16:9 in
Picture>Aspect ratio menu
Correct image
Image does not fit 16:9 screen
Turn Overscan on in the Picture>Overscan
menu
Correct image
Edges of image distorted
A B
A B
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Adjust color, tint, color temperature,
brightness, or contrast in the menus.
2. Pick another gamma setting
3. Pick another color space
1. Projected colors don’t match source
2. Colors are washed out or too deep
3. Image from component source appears greenish
Correct image
COLOR
COLOR
Correct image
Turn off Ceiling in Settings>System menu
Image upside down
B
A
A B
Image reversed left to right
Turn off Rear in Settings>System menu
Correct image
A
A B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Video Standard in
Picture>Advanced menu
Correct image
Video image “torn” and fragmented
AB
A
A B
Unplug projector; wait one minute; plug in
projector and turn it on: lamp lights
B
Make sure vents aren’t blocked; allow
projector to cool for one minute
Lamp won’t turn on, LED blinking red (page 12)
ScreenPlay
blinks
red
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer-specific troubleshooting
Only startup screen appears
Press the Source button
Computer image projected
Activate laptop’s external port
ScreenPlay
A
A
A
or restart
laptop
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating
system)
No computer image, just the words “Signal out of
range”
Computer image projected
A
A
Signal
range
out
A
of
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab, select
1280x720)
Image clear and not cropped
Image fuzzy or cropped
A
A
A
For a laptop,
disable laptop
monitor
or turn-on dual-
display mode
The video embedded in my PowerPoint
presentation does not play on the screen
Turn off the internal LCD display on your
laptop
Embedded video plays correctly
A
A
A
B
B
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Still having problems?
If you need assistance, visit our website or call us. See the inside of the back
cover for support contact information.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an over-
view of their functions:
Power–turns the projector on (page 9) and off (page 9).
Menu–opens the on-screen menus (page 23).
Select–confirms choices made in the menus (page 23).
Up/down arrows–navigates to and adjusts settings in the menus (page 23).
Auto image–resets the projector to the source.
menu navigation buttons
Presets–cycles through the 3 available user preset settings (page 26).
Keystone–adjusts squareness of the image (page 10).
Brightness–adjusts intensity of the image (page 24).
Resize–changes the aspect ratio (page 24).
Source–changes the active source (page 29).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote control
The remote uses two (2) provided AAA batteries. They are easily installed
by sliding the cover off the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
navigation buttons
To operate, point the remote at the projection screen or at the projector (not
at the video device or computer). The range of optimum operation is up to
30 feet (9.14m).
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 23 for more info on the menus.
The remote also has:
backlight button
•
Power button to turn the projector on and off (see page 12 for shut-
down info)
•
•
•
backlight button to light the remote’s buttons in the dark
Brightness and Contrast buttons to adjust the image
Blank button to display a blank screen instead of the current image (to
change the color of the blank screen, see page 30)
•
Source buttons to switch among sources (to assign a particular source
to a source button, see page 29) and a source toggle
•
•
•
•
Resize button to change the Aspect Ratio (see page 24)
Auto Image button to resynchronize the projector to the source
Preset button to restore stored settings (see page 26)
Overscan button to remove noise in a video image (page 26)
Troubleshooting the remote
•
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Make sure you’re pointing the remote at the projector or the screen, not
at the video device or the computer, and are within the remote range of
30 feet (9.14m).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing video images
Customizing the projector
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 23.
You can customize the projector for your specific setup and needs. See
page 29 to page 31 for details on these features.
•
•
For rear projection, turn Rear mode on in the Settings>System menu.
•
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source in the menus, or press the Resize button on the remote to
cycle through the options. See page 24.
For ceiling mounted projection, turn Ceiling mode on in the Set-
tings>System menu.
•
•
•
Turn the projector’s display messages and power-on chime on and off.
Turn on power saving features.
Specify blank screen colors and startup logos. Make the menus translu-
cent.
•
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu. See page 24.
•
Specify the menu language.
Select a different Color Temperature or use the Color Control to adjust
the gain and offset of the red, green, and blue color. See page 28.
•
•
Select a specific Color Space or Gamma. See page 26 and page 28.
Select a different Video Standard. Auto tries to determine the standard
of the incoming video. Select a different standard if necessary. See
page 28.
•
•
•
Turn Overscan on to remove noise around the video image. See
page 26.
Fine tune component inputs using the TrueLife™ adjustments. See
page 27.
Tune colors to your specifications using Blue Only and ADC Calibra-
tion. See page 31.
•
•
Choose High Power to maximize the light output. See page 29.
Make sure your DVD player is set for a 16:9 television. See your DVD
player’s user’s guide for instructions.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
To open the menus, press the menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button.
Menu
button
Main menu
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Previous, then press Select to go to
the previous menu; press the Menu button at any time to close the menus.
Keypad navigation
buttons
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to five (the most nested menus).
Dots
The menus are grouped by usage:
•
•
The Picture menu provides image adjustments.
The Settings menu provides set-up type adjustments that are not
changed often.
Settings menu
•
The About menu provides a read-only display of information about the
projector and source.
Picture menu
Certain menu items may be hidden until a particular source is connected.
For example, Tint is only available for NTSC video sources and will be hid-
den when other sources are active. Other menu items may be grayed out
when they are not available. For example, Brightness is grayed out until an
image is active.
About menu
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture menu
To adjust the following five settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes. All menu defaults are listed in a table starting on page 38.
Keystone: adjusts the image vertically and horizontally to make a squarer
image. The two keystones ranges are interdependent. The combined num-
ber of steps for both is 50. If one keystone is set to 65, it is 15 steps above the
center position of 50. This leaves 35 steps that the other keystone can vary
from the center of 50. This means it cannot go below 15 or above 85.
Keystone
Picture menu
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Brightness: changes the intensity of the image. You can also adjust bright-
ness from the keypad.
Color: (video sources only) adjusts a video image from black and white to
fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the
image.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
1.78:1, or 16:9. You can choose Native, 4:3, 16:9, Letterbox, or Natural Wide.
The default is 16:9. The goal is to show the most detail on the screen while
preserving the ratio of width to height. The native resolution of the projec-
tor is 1280x720. Use Native, 4:3 or Natural Wide for 4:3 input sources; use
Native, 16:9 or Letterbox for 16:9 input. Pressing the Resize button on the
remote cycles through these options.
Aspect ratio
Native: this mode bypasses the internal scaler, displaying the image with no
resizing. Since the native resolution is 1280x720 and 4x3 video images are
approximately 640x480, 4x3 images will always be smaller than the display
and will be centered in the display. Computer images 1024x768 or smaller
will also be centered in the display. If a 16x9 video source or a 1280x1024 or
larger computer source is viewed, it will display up to 1280 pixels and 720
lines from the center of the input.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
16:9: the default is 16:9, which preserves the 16:9 aspect ratio and is
designed to be used with content that is Enhanced for Widescreen TVs.
16:9 image
16:9 image input
16:9
aspect ratio
9
9
16
16
4:3: resizes the image from its original version to fit a standard 4:3
aspect ratio screen. If you have a 4:3 source on a 16:9 screen, the image
is placed in a 16:9 space, so black bars appear at the sides of the image.
4:3 image input
4:3 image on 16:9 screen
3
4:3 aspect ratio
9
16
4
Letterbox: preserves the 16:9 aspect ratio. If you have a 16:9 source and
screen, the image fills the screen. If your source is letterboxed, the
image is expanded to fill the screen.
letterbox image input
black bars
16:9 image fills 16:9 screen
letterbox
aspect ratio
9
3
black bars
4
16
Natural Wide: this mode stretches a 4:3 image to fill the entire 16:9
screen. The center two-thirds of the image is unchanged; the edges of
the image are stretched. The mode is only available when TrueLife is
active (see page 27).
4:3 image input
4:3 image fills 16:9 screen
natural wide
aspect ratio
3
9
16
4
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Presets: This allows you to customize settings and save the settings to be
restored later. To restore the factory default settings, choose Factory Reset in
the Settings>Service menu.
Save User Presets
Presets
To set a preset for the current source, adjust the image, select Save Settings
in the Presets menu, then choose Save User 1, 2, or 3. You can recall these
settings in the future by selecting the appropriate user presets.
Gamma: Gamma tables contain preset intensity configurations optimized
for the input source. You can select a gamma table that has been specifically
tuned for either film, CRT (Cathode Ray Tube), video, Bright Room, or PC
input. (Film input is material originally captured on a film camera, like a
movie; video input is material originally captured on a video camera, like a
TV show or sporting event.) White Peaking increases the brightness of
whites that are near 100%.
Gamma
NOTE: Your viewing preferences may vary. Cycle through the gamma
options and pick the one you like the best.
Overscan
Overscan: (video sources only) removes noise around the video image.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
The following 4 options are for computer or HDTV sources only.
Phase: adjusts the phase of the video signal’s digital conversion.
Tracking: adjusts the frequency of the video signal’s digital conversion.
Horizontal/Vertical Position: adjusts the position of the source.
Advanced
Sync Threshold Adjust: If a hardware device, such as a DVD player, is not
syncing properly with the projector, adjust this option to help it to sync
when connected to the projector.
TrueLife: This option refers to Faroudja’s TrueLife processing of the image.
All standard definition interlaced video signals (composite, S-video and
component) are routed through this processor. Extended and High Defini-
tion progressive component sources are not routed though this processor by
default. You can turn TrueLife on to route these signals through the proces-
sor and then adjust the following 3 options:
TrueLife
Chroma Detail: This adjusts the color sharpness.
Luma Detail: This adjusts the overall sharpness (edge enhancement) of
the Luma signal.
Chroma Delay: aligns the Luma and Chroma signals.
Film Mode
CCS: (Cross Color Suppression) processes the signal to remove any color
information from the luma portion of the signal. It is On for all composite
signals, Off for all component signals, and can be turned on or off for all S-
video signals.
Film Mode: controls deinterlacing. If 2:2/3:2 Enable is selected, the deinter-
lacer attempts to perform a 3:2 pulldown, assuming the source was origi-
nally created on 24fps film. If the original source is 30fps film, you should
select NTSC 2:2 pulldown.
Noise Reduction
Noise Reduction: adjusts signal noise reduction. Choose Off to have no
noise reduction, choose Auto to have the software determine the amount of
noise reduction, or choose Manual and adjust the Level. Skintone Bypass
prevents the noise reduction from being performed on skin tones, thus pre-
venting them from appearing overly softened.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Space: This option applies to computer and HDTV sources (it won’t
appear in the menu for video sources). It allows you to select a color space
that has been specifically tuned for the video input. When Auto is selected,
the projector automatically determines the standard. To choose a different
setting, turn off Auto, then choose RGB for computer sources, choose
REC709 for component 1080i or 720p sources, or choose REC601 for compo-
nent 480p or 576p sources.
Color Space
Color Temperature: changes the intensity of the colors. Select a listed
value.
Color Temperature
Color Control: allows you to individually adjust the gain (relative warmth
of the color) and the offset (the amount of black in the color) of the red,
green, and blue colors.
Color Control
Video Standard
Video Standard: When it is set to Auto, the projector attempts to pick the
video standard automatically based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If
the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
dard menu.
VCR: When checked, the VCR option is used to eliminate discoloration of
about 25% of the image near the top caused by poor quality input image
content.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings menu
Sources: allows you to assign a particular input to a specific source key on
the remote and enables or disables Autosource. When Autosource is not
checked, the projector defaults to the last-used source. If no source is found,
a blank screen displays. When Autosource is checked, the projector checks
the last-used source first at power up. If no signal is present, the projector
checks the sources in order until a source is found or until power down.
Settings menu
Sources
You can use the Source Enable feature to eliminate certain sources from this
search, which will speed the search. By default, the check boxes for all
sources are checked. Uncheck a source’s box to eliminate it from the search.
System
All options in this menu toggle between on and off.
Source Enable
Source 1
Rear: reverses the image so you can project from behind a translucent
screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
NOTE: It is recommended that all final image adjustments in Ceiling
mode are made once the unit has fully warmed up (approximately 20
minutes).
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector receives power. This
allows control of ceiling mounted projectors with a wall power switch.
System menu
Display Messages: displays status messages (such as “Searching”) in
the lower-left corner of the screen.
High Power: Turn this on to increase the light output of the lamp. This
also shortens lamp life and increases fan noise.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Translucent OSD: makes the menus translucent. This prevents the
image from being completely covered by the menus while you are
making image adjustments.
Chime: turn this on to hear a sound when the Power button is pressed.
System menu
Sleep Timer: allows you to force the projector to automatically shutoff
after 4 hours.
Power Save: when On, the lamp is automatically turned off after no
signals are detected for 20 minutes. After 10 additional minutes with no
signal, the projector powers down. If an active signal is received before
the projector powers down, the image will be displayed.
Startup logo
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen at startup and when no source is detected.
Blank Screen: determines what color displays when you press the Blank
button on the remote or when no source is active.
Blank Screen
Language: allows you to select a language for the onscreen display of
menus and messages.
Language
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default
after displaying a confirmation dialog box.
Service menu
Test Patte rn: displays a test pattern when the Blank button on the remote is
pressed. To select the patterns, use the up/down arrows on the remote or
keypad. Press the remote’s Blank button to exit test pattern mode.
Blue Only: turns off the Red and Green portions of the input, allowing you
to properly adjust the color balance with a SMPTE color bar pattern.
ADC Calibration: allows adjustment of the calibrated ADC values so that
color accuracy can be optimized. Adjust the slidebars for each value and
note the change in the appropriate color. Use a component input when
adjusting the Component controls.
Service Code: only used by authorized service personnel.
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the projection lamp
The lamp hour timer in the About menu counts the number of hours the
lamp has been in use. Twenty hours before the lamp life expires, the mes-
sage “Change lamp” appears on the screen at startup. If the maximum lamp
time is exceeded, the lamp will not light. In this case, after replacing the
lamp you must reset the lamp hours by simultaneously pressing both
Brightness buttons on the keypad and holding them for 10 seconds. You
can order new lamp modules from your dealer.
Lamp hours used
turn off and unplug
the projector
1 Turn off the projector and unplug the power cable.
2 Wait 60 minutes to allow the projector to cool thoroughly.
wait 60 minutes
3 Turn the projector upside down and remove the lamp door by removing
the two screws and sliding the lamp door tabs out of the three tab bays.
CAUTION: Never operate the projector with the lamp door removed.
This disrupts the air flow and causes the projector to overheat.
4 Loosen the captive screw on the lamp module.
loosen the screw on lamp module
bail wire
32
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS:
•
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
•
•
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
•
Be extremely careful when removing the lamp module. In the unlikely
event of the lamp rupturing, discard any edible items placed in the sur-
rounding area and thoroughly clean the area along all sides of the pro-
jector. Wash hands after cleaning the area and handling the ruptured
lamp. This product has a lamp which contains a very small amount of
mercury. Dispose of it as required by local, state or
federal ordinances and regulations. For more information see
5 Carefully remove the lamp module by grasping and lifting the metal
bail wire. Dispose of the lamp in an environmentally proper manner.
6 Install the new lamp module, making sure that it is properly seated.
7 Tighten the single screw.
8 Replace the lamp door by sliding the tabs into the tab bays and tighten-
ing the two screws.
9 Plug in the power cable, then press the Power button to turn the projec-
tor back on.
10 Reset the lamp hour timer.
Resetting the lamp timer
To reset the lamp age, simultaneously holding down the two Brightness
buttons on the projector’s keypad for 10 seconds.
1
2
Y
Y
IR in
trigger
trigger
1
2
8
1
D5
M1-DA
vesa
2
Pb
Pr
Pb
Pr
7
video
4
serial control
5
s-video
Using the security lock
6
component
3
component
The projector has a security lock for use with a PC Guardian Cable Lock
System. Refer to the information that came with the lock for instructions on
how to use it.
security lock
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Projected image size
Appendix
Table 4:
Range of projection distances for a given screen size
Red LED behavior and projector errors
If the projector is not functioning properly and the red LED is blinking, con-
sult Table 2 to determine a possible cause. There are two second pauses
more details on the red LED error codes.
Projection Distance
16:9 Screen
dimensions
(inches/m)
Screen
diagonal
(inches/m)
Maximum
zoom
Minimum
zoom
(feet/m)
(feet/m)
27x48
.7x1.2
55.1/1.4
68.8/1.75
82.6/2.1
91.8/2.3
99.8/2.5
105.6/2.7
110.1/2.8
119.3/3.0
133.1/3.4
6.7/2.03
8.3/2.5
8.3/2.54
10.4/3.2
12.5/3.8
13.9/4.2
15.1/4.6
16.0/4.9
16.7/5.1
18.1/5.5
20.1/6.1
Table 3: Red LEDs
34x60
.9x1.5
Red LED Behavior
Explanation
41x72
1.0/1.8
10.0/3.0
11.1/3.4
12.1/3.7
12.8/3.9
13.3/4.1
14.4/4.4
16.1/4.9
One (1) blink
The lamp won't strike after five (5)
attempts. Check the lamp and lamp door
installations for loose connections.
45x80
1.1x2.0
49x87
1.2/2.2
Three (3) blinks
The projector has shut down the lamp.
Turn off the projector, wait one minute,
then turn it back on. Or, replace the lamp.
Contact Technical Support for repair if
replacing the lamp does not solve the
problem.
52X92
1.3X2.3
54X96
1.4X2.4
59X104
1.5X2.6
Four (4) blinks
Five (5) blinks
The fan has failed. Replace the lamp (the
lamp module contains a fan). Contact
Technical Support for repair if replacing
the fan does not solve the problem.
65X116
1.7X2.9
The projector is overheating. Check for a
blocked air vent. Contact Technical Sup-
port for repair if clearing the air vents
does not solve the problem.
tive image size calculator.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Source compatibility
Table 5:
Table 6:
Source Compatibility
Projector Inputs and Outputs
Video
Component and RGB HDTV (720p, 1035i, 1080p, 1080p-24Hz)
DVI/HDCP for digital video and encrypted digital video
Component EDTV (480p, 576p progressive scan),
SECAM: M, Component, Composite and S-Video standard
video (480i, 576i, 576i RGB SCART with adapter,
NTSC, NTSC M 4.43,
2-Component
(Gold RCA)
HDTV, EDTV, and Standard TV component
1-Component
(D5)
HDTV, EDTV, Standard TV, RGB SCART with adapter
PAL: B, H, I, M, N)
2-S-Video
Standard Video
Standard Video
Computer
Digital and analog PC, Macintosh, 1280x1024 resolution
USB and RS-232
1-Composite
(RCA)
Communi-
cation
1-M1-DA VESA HDTV RGB, HDTV component, DVI, computer, and USB
1-HD15 VESA
HDTV RGB, HDTV component, computer
RS-232
1-9-pin Dsub
male
1-3.5 mm mini
jack
IR Repeater (Niles/Xantech compatible)
2-3.5 mm mini
jack
1-12v screen drop, 1-12v 4:3 aspect “curtains”
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector dimensions for ceiling mount installations
2.1”
53.7mm
2.3”
57.8mm
8.7”
221.4mm
2.6”
64.9mm
11.3”
288.1mm
4.3”
109.5mm
0.14”
3.6mm
8.5”
216mm
12.3”
312.7mm
dimensions of optional cable cover: 12.4 x 3.9 x 3.2” (315 x 100 x 82mm)
total length with optional cable cover: 16.2” 411.5mm)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
A read command returns the range and the current setting, for example:
RS-232 terminal specifications
Communication configuration
Function
Brightness
Lamp hours
Command
(BRT?)
Response
(0-22, 10)
To control the projector from an LCD control panel, connect an RS-232 cable
to the serial control connector on the projector and set your computer’s
serial port settings to match this communication configuration:
(LMP?)
(0-9999, 421)
Setting
Value
19,200
8
A write request example: (AAA####) where
Bits per second
Data bits
(
starts the command
denotes the command
AAA
####
Parity
None
1
denotes the value to be written
(leading zeros not necessary)
Stop bits
Flow control
Emulation
None
VT100
)
ends the command
Some commands have ranges, while others are absolute. If a number
greater than the maximum range is received, it is automatically set to the
maximum number for that function. If a command is received that is not
understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on.
The one exception is the Power command, where 0 is off and 1 is on.
Command format
All commands consist of 3 alpha characters followed by a request, all
enclosed in parentheses. The request can be a read request (indicated by a
“?”) or a write request (indicated by 1 to 4 ASCII digits).
A read request format: (AAA?) where
Function
Brightness
Power
Command
(BRT10)
Response
(
starts the command
denotes the command
denotes the read request
ends the command
Sets the brightness to 10
Turns power off
Turns power on
?
(PWR0)
AAA
Power
(PWR1)
?
)
Power
(PWR9999)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported commands
Color Temp
TMP
0-2
2
0 = 9300
1 = 8200
2 = 6500
Function
Command Range
Default
Aspect Ratio
ARZ
0-4
0 = Native
1 = 16:9
2 = 4:3
3 = Letterbox
4 = Natural Wide
1
Contrast
CON
CCS
DMG
RST
4-252
0-1
128
0
CCS
Display Messages
Factory Reset (Write only)
Gamma Table
0-1
1
0-1
n/a
3
GTB
0-5
0 = CRT
1 = Film
2 = Video
3 = Bright Room 1
4 = Bright Room 2
5 = PC
Auto Chime Enable
Auto Power
Auto Source
Blank
ACE
APO
ASC
BLK
BSC
0-1
0-1
0-1
0-1
1
0
0
0
0
Blank Screen
0-2
0 = black
1 = blue
2 = white
Green Color Offset
Green Gain
GCO
GCG
HPE
1-63
32
32
0
1-63
High Power Enable
Horizontal Position
Keystone (Vertical)
Keystone (Horizontal)
Lamp Hours (Read only)
Lamp Reset
0-1
Blue Color Offset
Blue Gain
BCO
BCG
BRT
1-63
1-63
2-254
0-1
32
32
128
0
HPS
n/a
n/a
128
128
0
DKC
DKH
LMP
53-203
63-193
0-32767
0-32767
0-20
Brightness
Ceiling
CEL
Chroma Detail
Color
CDE
CLR
CSM
0-20
2-254
0
LMR
LDE
0
128
7
Luma Detail
0
Color Space
0-7
0 = RGB
3 = REC601
2 = REC709
7 = Auto
Menu
MNU
NAV
0-1
0
Menu Navigation
0-4
0 = up
1 = down
4 = select
n/a
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Language
LAN
0-11
0
Red Color Offset
Red Gain
RCO
RCG
SBE
1-63
1-63
0-1
32
32
0
0 = English
1 = French
2 = German
3 = Spanish
4 = Chinese Tradi-
tional
5 = Japanese
6 = Korean
7 = Portuguese
8 = Russian
9 = Norwegian
10 = Chinese Sim-
plified
Skintone Bypass Enable
Source
SRC
0-7
2
0 = Video 1, M1
1 = Video 2, VESA
2 = Video 3, Com-
ponent 1
3 = Video 4,
S-Video 1
4 = Video 5,
S-Video 2
5 = Video 6,
Component 2
6 = Video 7,
Composite
11 = Italian
NTSC 2:2 Pulldown Enable
Noise Reduction Enable
NPE
NRE
0-1
0
0
0-2
7 = Video 8, D5
0 = Off
1 = Auto
2 = Manual
Startup Logo
Tint
DSU
TNT
MTS
TOE
TLE
0-1
2-254
n/a
1
128
n/a
1
Noise Reduction Level
Overscan
NRL
OVS
0-10
5
Tracking
127=Crop
128=Off
129=Zoom
128
Translucent OSD
TrueLife Enable
Vertical Position
Video Standard
0-1
0-1
n/a
0
VPS
n/a
0
Phase
MSS
PWR
PSV
0-31
0-1
n/a
0
VSU
0-3
Power
0 = Auto
1 = NTSC
2 = PAL
3 = SECAM
Power Save
Presets
0-1
1
PST
0-2
0
0 = User 1
1 = User 2
2 = User 3
Rear Project
REA
0-1
0
39
Download from Www.Somanuals.com. All Manuals Search And Download.
computer 11
power cable 8
video device 8
connector panel 5
contacting InFocus 19
Contrast 24
Numerics
12v triggers 5, 35
16x9 5, 14, 22, 24, 25
4x3 25
4x3 aspect trigger 5
A
ADC Calibration 31
adjusting image 10, 24
Advanced menu 27
Aspect Ratio 24
Auto Power 29
Autosource 29
B
Blank Screen 30
blinking green 12
blinking red 12
Blue Only 31
customer service contact information 19
D
D65 colors 10
dimensions of projector 36
Display Messages 29
DVI connector 8
E
error codes 34
F
Factory Reset 31
Faroudja video proecessing 27
Film Mode 27
focus 10
C
cable box 7
CCS 27
Ceiling 29
Chime 30
focus ring
threaded 10
fuzzy image 18
G
Chroma Delay 27
Chroma Detail 27
cleaning the lens 31
CLI commands 38
Color 24
Color Control 28
Color Space 28
Color Temperature 28
colors are incorrect 15
command line interface commands 38
component cable connector 8
composite video connector 8
computer, connecting 11
connecting
Gamma 26
H
HDTV 7, 22, 24, 35
HDTV sources 27, 28
height, adjusting 9
High Power 29
Horizontal Position 27
I
image
display video 9
focussing 10
size 6
zooming 10
40
Download from Www.Somanuals.com. All Manuals Search And Download.
image does not fit screen 14
image edges distorted 14
image not centered 13
image not square 14
image offset 6
image reversed 15
image size matrix 34
image sizes 6
N
Native 24
Natural Wide 25
no computer image 17
no startup screen 13
Noise Reduction 27
O
offset 6
image torn 16
only startup screen appears 17
Overscan 26
P
image upside down 15
InFocus website 2
inputs 35
IR repeater 5
K
keystone 10, 24
L
lamp replacement 32
lamp timer, resetting 33
lamp won’t turn on 16
Language 30
Phase 27
Picture menu 24
Power button 9
power cable 8, 11
Power Save 12, 30
Presets 26
projection distance 6, 34
projector
adjusting height 9
cleaing the lens 31
compatible sources 35
connecting a video device 8
connector panel 5
controlling projection screen 5
customizing 22
dimensions 36
LED
blinking green 12
blinking red 16
solid green 12
LED behavior 12, 34
Lens cleaning 31
Letterbox 25
Luma Detail 27
M
displaying a video image 9
image sizes 34
Main menu 23
Maintenance 31
menus 23
inputs and outputs 35
LED behavior 12
maintaining 31
menus 23
optimizing images 22
overview 4
changing the language 30
making translucent 30
positioning 6, 9
41
Download from Www.Somanuals.com. All Manuals Search And Download.
remote control 21
replacing the lamp 32
resetting lamp timer 33
saving settings 26
security lock 33
System menu 29
T
Test Pattern 31
threaded focus ring 10
Tint 24
setting up 6
Tracking 27
shutting down 12
troubleshooting 12
Translucent OSD 30
triggers 5
R
Troubleshooting 12, 13, 17
TrueLife settings 27
TV tuner 7
Rear 29
registering your projector 4
remote control 21
replacing the lamp 32
resetting the lamp timer 33
Resize button 24
resolution 4
RS-232
connecting 5, 11
RS232
V
Vertical Position 27
VESA connector 8
video connections 7
video images, optimizing 22
video processing 27
W
warranty 19
website 2
White Peaking 26
Z
specifications 37
S
security lock 33
Serial connection 11
serial connection 5, 37
Service Code 31
Service menu 31
Settings menu 29
shutting down the projector 12
Sleep Timer 30
zoom 10
solid green 12
solid red 12
source compatibility 35
Source troubleshooting 13, 17
Sources 29
Startup Logo 30
S-video connector 8
Sync Threshold Adjust 27
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
WARRANTY LIMITATION AND EXCLUSION
THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR
ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-
CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.
InFocus shall have no further obligation under the foregoing Limited War-
ranty if the Product has been damaged due to abuse, misuse, neglect, smoke
exposure (cigarette or otherwise), accident, unusual physical or electrical
stress, unauthorized modifications (including use of an unauthorized
mount), tampering, alterations, or service other than by InFocus or its
authorized agents, causes other than from ordinary use or failure to prop-
erly use the Product in the application for which said Product was intended.
This Limited Warranty excludes Product cleaning, repair, or replacement of
plastics due to cosmetic damage and damage as a result of normal wear.
Product repair outside of the terms of the Limited Warranty will be on a
time and materials basis. Prolonged Product “demonstration” causes
unusual Product wear and is not considered normal use under the terms of
this Limited Warranty.
Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-
poration (“InFocus”) warrants that the Projector, Lamps and Accessories
(hereinafter collectively or individually referred to as “Product” as appro-
priate) purchased from InFocus, an InFocus distributor, or an InFocus
reseller will conform to InFocus’ specifications and be free from defects in
material or workmanship for the respective Limited Warranty period pro-
vided below. InFocus does not warrant that the Product will meet the spe-
cific requirements of the end-user customer.
If the Product while subject to this Limited Warranty, is defective in material
or workmanship during the warranty period, then InFocus, at its option,
will REPAIR or REPLACE the Product.
All exchanged parts and Products replaced under this Limited Warranty
will become property of InFocus. InFocus' sole obligation is to supply (or
pay for) all labor necessary to repair the Product found to be defective
within the Limited Warranty period and to repair or replace defective parts
with new parts or, at the option of InFocus, serviceable used parts that are
equivalent or superior to new parts performance. Limited Warranty periods
are as follows:
The Accessory Product Limited Warranty covers the accessory item only
and excludes normal wear. The Lamp Product Limited Warranty excludes
expected lamp degradation.
Remanufactured Products and Software Products are exempt from the fore-
going Limited Warranty. Please refer to the appropriate Remanufactured
Product Limited Warranty or Software Product Limited Warranty for appli-
cable Warranty information.
•
Projector Product Limited Warranty Period (Excluding Lamps):
Two ( 2 ) ye a r s from date of purchase.
•
Lamp Product Limited Warranty Periods: From the date of Projector
Product purchase, the original installed lamp shall have a 90-day or 500
hours usage Limited Warranty Period, whichever comes first.
Replacement Lamps purchased at the time of Projector Product pur-
chase will have a 90-day or 500 hours usage Limited Warranty Period
from the date of installation, whichever comes first.
Replacement lamps purchased after the time of Projector Product pur-
chase shall have a 90-day or 500 hours usage Limited Warranty Period
from the date of replacement lamp purchase, whichever comes first.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-
CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND
THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED
OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.
SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS
MAY NOT APPLY TO YOU.
•
Accessory Product Limited Warranty Period: one (1) year from date
of purchase.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty Period
No repair or replacement of Product or part thereof shall extend the Limited
Warranty period as to the entire Product. Warranty on the repair part and
workmanship shall only be effective for a period of ninety (90) days follow-
ing the repair or replacement of that part or the remaining period of the
Product Limited Warranty whichever is greater.
The Limited Warranty periods hereof commence on the date of purchase by
the end-user customer. These Limited Warranty provisions shall apply only
to the end-user purchaser (first person or entity that purchased a new Prod-
uct for personal or business use and not for the purpose of distribution or
resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS
WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE
DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL
SUCH CONSUMER RIGHTS.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY
WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN
NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF
THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND
UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-
CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE
STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING
INFOCUS’ LIABILITY.
Limitation on Bringing Action - No action, regardless of form, arising out
of the agreement to purchase the Product may be brought by purchaser
more than one year after the cause of action has accrued.
Governing Law - Any action, regardless of form, arising out of the agree-
ment to purchase the Product is governed by Oregon law.
Mandatory Arbitration – Any action, regardless of form, arising out of the
agreement to purchase the Product is subject to mandatory arbitration.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS, DEPENDING ON JURISDIC-
TION.
To Be Eligible For Limited Warranty Coverage
Any person exercising a claim under this Limited Warranty must establish
to the satisfaction of InFocus both the date of purchase and that the Product
was purchased new. The sales receipt or invoice, showing the date of pur-
chase of the Product is the proof of the date of purchase.
To Obtain Warranty Service
During the Limited Warranty period, to exercise this Limited Warranty, the
purchaser must first contact 1) InFocus, 2) a service facility authorized by
InFocus or 3) the place of original purchase. InFocus Customer Service –
For Warranty service, the purchaser will be advised to return or deliver the
defective Product freight and all fees prepaid, to an InFocus Service Center
or to a service facility authorized by InFocus. When returning Product to
InFocus, a Service Request Number (SR #) is required and must be clearly
displayed on the outside of the shipping carton or a similar package afford-
ing an equal degree of protection. InFocus or the service facility authorized
by InFocus will return the repaired/replaced Product freight prepaid to the
purchaser.
Products returned for Warranty service must be accompanied by a written
letter that: (i) explains the problem; (ii) provides proof of date of purchase;
(iii) provides the dealer’s name; and (iv) provides the model and serial
number of the Product. Upon request of InFocus Corporation or an autho-
rized repair center for InFocus, proof of legal import must accompany the
warranty repair Product, otherwise the Product must be returned to the
place of original purchase, to the manufacturer (Purchaser must bear all tax,
duty and freight), or the Purchaser must bear charges for the warranty
repair.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
|