InFocus Projector IN5102 User Manual

IN5102/IN5104/IN5106  
Regulatory models W50, W55  
User’s Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation is subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interferences received,  
including interference that may cause undesired operation.  
Declaration of Conformity  
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon  
97070 USA  
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands  
We declare under our sole responsibility that this projector conform to the following  
directives and norms:  
EMC Directive 2004/108/EC  
EMC: EN 55022  
EN 55024  
EN 61000-3-2  
EN 61000-3-3  
Changes or modifications not expressly approved by InFocus Corporation may void  
authority to operate the equipment.  
EN 55022 Warning  
This is a Class A product. In a domestic environment it may cause radio interference,  
in which case the user may be required to take adequate measures. The typical use is  
in a conference room, meeting room or auditorium.  
Low Voltage Directive 2006/95/EC  
Safety: IEC 60950-1: 1st Edition  
Canada  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.  
Trademarks  
Agency Approvals  
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple  
Computer, Inc. IBM is a trademark or registered trademark of International Business  
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered  
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or  
registered trademarks of Adobe Systems Incorporated. HDMI, the HDMI logo and  
High-Definition Multimedia Interface are trademarks or registered trademarks of  
HDMI Licensing LLC. InFocus, In Focus, and INFOCUS (stylized) are either  
registered trademarks or trademarks of InFocus Corporation in the United States and  
other countries.  
UL, CUL  
Other specific Country Approvals may apply, see please product certification label.  
InFocus reserves the right to alter product offerings and specifications at any time  
without notice.  
This document applies to model W50: IN5106, C500, IN5102, C447.  
Input ratings: 100-120/220-240Vac, 5.0/2.1A, 50/60Hz  
FCC Warning  
Battery Safety Information  
This equipment has been tested and found to comply with the limits for a Class A  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the  
instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference at his  
own expense. This device complies with part 15 of the FCC Rules.  
CAUTION: Risk of explosion if the battery in this projector is replaced with the  
incorrect type of battery. See page 35 for battery replacement instructions.  
Remote Control Warning  
Laser radiation class II product; wavelength 650nm; maximum output 1mW. Remote  
control complies with applicable requirements of 21 CFR 1040.10 and 1040.11. Remote  
control complies with applicable requirements of EN 60825: 1994+A11+A2.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not look into laser beam emitted from the front of the remote control  
Do not look into laser beam emitted from the front of the remote control  
Location of laser beam warning labels on remote  
Location of laser beam warning labels on remote  
OR this label  
OR this label  
Location of laser beam warning labels on remote  
Location of laser beam warning labels on remote  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
For complete details on connecting and operating the projector, refer to this  
User’s Guide. Electronic versions of this User’s Guide in multiple languages  
are available on our website.  
Introduction  
5
Included Items  
Positioning the projector  
Connecting a computer  
5
7
8
8
10  
11  
12  
13  
15  
15  
The website also has technical specifications (an interactive image size cal-  
culator, laptop activation commands, connector pin outs, a glossary, the  
product data sheet), a web store to buy accessories, and a page for online  
registration. See the inside of the back cover for a list of all relevant web  
addresses.  
Required computer connections  
Displaying a computer image  
Adjusting the image  
Connecting a video device  
Displaying a video image  
Shutting down the projector  
Troubleshooting your setup  
Using the keypad buttons  
Using the remote control  
Using the audio  
22  
23  
24  
Optimizing computer images  
Presentation features  
Optimizing video images  
Customizing the projector  
25  
25  
26  
26  
Using the menus  
Picture menu  
27  
28  
31  
Settings menu  
Maintenance  
35  
35  
35  
36  
38  
38  
Cleaning the lens  
Replacing the clock batteries  
Replacing the projection lamp  
Cleaning the dust filter  
Using the security lock  
Appendix  
39  
39  
42  
Projected image size  
RS-232 commands  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Operating Considerations for Safety  
Place the projector in a horizontal position no greater than 8 degrees off  
axis.  
Locate the projector in a well-ventilated area without any obstructions  
to intake or exhaust vents. Do not place the projector on a tablecloth or  
other soft covering that may block the vents.  
Locate the projector at least 4' (1.2 m) away from any heating or cooling  
vents.  
m
5
8
.
/ 1  
/ 2  
.
4
m
5
Use only approved ceiling mounts.  
Warning: To prevent eye injury if the projector is ceiling mounted,  
wear protective eyewear before opening lamp door. A warning sticker  
is included with the user documentation. Place this sticker on the lamp  
door if the projector is mounted on the ceiling.  
Follow these instructions to help ensure image quality and lamp life over  
the life of the projector. Failure to follow these instructions may affect the  
warranty. For complete details of the warranty, see the Warranty booklet.  
Only genuine InFocus lamps are tested for use in this projector. InFocus  
is not liable for the performance, safety or certification of any other  
lamps. The use of other lamps violates the projector warranty and  
voids all certification marks on this projector.  
Use only the power cord provided. A surge-protected power strip is  
recommended.  
Refer to this manual for proper startup and shutdown procedures.  
Hg – Lamp contains mercury. Manage in accordance with local  
disposal laws. See www.lamprecycle.org.  
In the unlikely event of a lamp rupture, particles may exit through the  
projector vents. When the projector is turned on, keep people, food,  
and drinks out of the "keep out" area under and around the projector, as  
indicated by the "X" areas.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projector components and features: front  
Introduction  
Your new multimedia projector provides three computer, three video, and  
four audio inputs, one audio output, and RS-232 and Network control. It  
has XGA 1024x768 resolution. Optional user-changeable short, fixed short,  
long and ultra long throw lenses make this a flexible product suitable for  
many different uses. The projector is easy to connect, easy to use, and easy  
to maintain.  
zoom/focus/offset door  
remote  
control  
receiver  
Product specifications  
To read the latest specifications on your multimedia projector, be sure to  
visit our website. Web address information is located on the back inside  
cover of this User’s Guide.  
air intake  
vent  
heat vent  
elevator foot release  
leveling foot  
Online Registration  
Register your projector on our website to receive product updates,  
announcements, and registration incentives. See the inside back cover for  
the web address.  
Projector components and features: back  
Included Items  
lamp door  
projector  
remote  
lens cap*  
power cable  
VESA computer cable  
power switch  
power plug  
A/V cable  
connectors  
documentation  
*the lens cap tether can attach the lens cap to the projector if desired.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connector Panel  
The projector provides three computer and three video connection options:  
component video  
BNC  
remote  
control  
receiver  
(IR)  
audio in 1,2  
USB  
one VESA computer  
VESA computer  
RS232  
RJ-45  
lock  
serial control  
one HDMI™ (High Definition Multimedia Interface)*  
HDMI  
monitor  
one component BNC (G/Y, B/C /P , R/C /P , H, V)  
B
B
R
R
one component RCA video (Pr, Pb, Y)  
one S-video  
one composite RCA video  
The projector provides computer and video connectors for audio support:  
two composite RCA stereo audio (L, R)  
one audio out  
composite  
video  
audio in 3,4  
power connector and switch  
wired remote  
s-video  
external  
speakers  
(audio out)  
two audio ins  
speaker  
The projector also provides the following connectors:  
one wired remote  
one monitor out  
RS-232 serial connector (for serial control)  
RJ-45 connector (for networked control)  
The RS-232 Command Line Interface (CLI) specifications and commands  
are available in the Appendix and on our website. See the back inside cover  
of this User’s Guide for website information.  
* HDMI is an industry standard, uncompressed, all-digital audio/video  
interface that connects between sources, such as set-top boxes, DVD play-  
ers, and receivers and your projector. To take advantage of HDMI 1.3 you  
must have a 1.3-compatible source. The HDMI, because it is a digital signal,  
yields the highest quality image. It is common for these signals to be  
encrypted with HDCP (high-bandwidth digital-content protection). Your  
new projector ships standard with decryption codes so you can enjoy these  
high quality, all digital images.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Positioning the projector  
To determine where to position the projector, consider the size and shape of  
your screen, the location of your power outlets, and the distance between  
the projector and the rest of your equipment. Here are some general guide-  
lines:  
Projection angle in 4:3 mode (default)  
10 ft high image  
9:1  
1:1  
Position the projector on a flat surface at a right angle to the screen. The  
projector (with the standard lens) must be at least 3 feet (0.9m) from the  
projection screen.  
9:1  
bottom of image  
10% below  
lens center  
Position the projector within 10 feet (3m) of your power source and  
within 6 feet (1.8m) of your video device (unless you purchase exten-  
sion cables). To ensure adequate cable access, do not place the projector  
within 6 inches (.15m) of a wall or other object.  
lens center  
1:1  
bottom of image  
50% below  
lens center  
If you are installing the projector on the ceiling, refer to the installation  
guide that comes with the Ceiling Mount Kit for more information. To  
turn the image upside down, see “Ceiling” on page 31. We recom-  
mends using an authorized ceiling mount. The Ceiling Mount Kit is  
sold separately; visit our website for more information.  
Position the projector the desired distance from the screen. The distance  
from the lens of the projector to the screen, the zoom setting, and the  
video format determine the size of the projected image. For information  
about image sizes at different distances, see “Projected image size” on  
page 39.  
For the standard lens that comes with the projector, the image exits at a  
given angle. However, the lens shift feature makes the image offset  
variable. The image offset is 90% at a 9:1 ratio when the projector is in  
4:3 mode (default mode). This means that if you have an image 10’  
high, the bottom of the image will be 1’ below the center of the lens.  
The image offset is 50% when the lens shift is at a 1:1 ratio. This means  
that if you have an image 10’ high, the bottom of the image will be 5’  
below the center of the lens.  
For information about the optional lenses image offsets, see “Projected  
image size” on page 39.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a computer  
connect computer cable  
Required computer connections  
Connect one end of the VESA computer cable to the Computer 2 connector  
on the projector. Connect the other end to the video port on your computer.  
If you are using a desktop computer, you first need to disconnect the moni-  
tor cable from the computer’s video port.  
Connect the black power cable to the connector on the back of the projector  
and to your electrical outlet.  
connect power cable  
NOTE: Always use the power cable that shipped with the projector.  
Optional computer connections  
You can also connect to your computer using optional BNC or HDMI cables.  
Connect the BNC connectors on the BNC cable to the appropriate Com-  
puter 3 connectors on the projector. Connect the other end to the video port  
on your computer. If you are using a desktop computer, you first need to  
disconnect the monitor cable from the computer’s video port.  
connect BNC cable  
connect HDMI cable  
Or, connect the HDMI cable to the Computer 1 connector.  
To have sound with your presentation, connect the audio cable to your com-  
puter and to the corresponding computer Audio In connector on the projec-  
tor. You can assign a particular source to a particular audio in connector, see  
page 31.  
connect audio cable  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you are using a desktop computer and want to see the image on your  
computer screen as well as on the projection screen, plug the monitor cable  
to the Monitor out connector on the projector.  
connect monitor cable  
connect RS-232 cable  
You can control the projector from an LCD control panel, touch screen, or  
other control device or computer by connecting an RS-232 cable to the pro-  
jector’s Serial Control connector. Specific RS-232 commands can be found  
in the Service and Support section of our website and in the Appendix.  
The projector can be managed by networking software through its Network  
(RJ-45) connector. Detailed instructions on this feature can be found on our  
website.  
connect CAT-5 cable  
Network  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Displaying a computer image  
Remove the lens cap.  
remove lens cap  
Press the power switch on the back of the projector to the on (I) position.  
The Power light on the Status Indicator Panel (page 15) lights green.  
press Power switch press Power button  
2
Press the Power button on the top of the projector or the remote.  
The Power light blinks green and the fans start to run. When the lamp  
comes on, the startup screen is displayed and the light is steady green. It can  
take a minute for the image to achieve full brightness.  
1
? No startup screen? Get help on page 16.  
turn on computer  
Turn on your computer.  
The computer’s image should appear on the projection screen. If it doesn’t,  
press the Source button on the keypad or remote.  
activate laptop’s external port  
Make sure your laptop’s external video port is active.  
Many laptops do not automatically turn on their external video port when a  
projector is connected. Usually a key combination like FN + F5 is used to  
turn the external display on and off. Refer to your computer’s documenta-  
tion to learn your computer’s key combination.  
? No computer image? Get help on page 16.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the image  
release  
button  
adjust height  
release  
button  
Adjust the height of the projector, if necessary, by pressing the release but-  
tons on each side of the projector’s front to extend the elevator feet.  
elevator  
foot  
elevator  
foot  
Position the projector the desired distance from the screen at a 90 degree  
angle (perpendicular) to the screen.  
adjust distance  
See page 39 for a table listing screen sizes and distances.  
Adjust the zoom or focus by rotating the Zoom or Focus rings inside the  
lens door until the desired image size and focus are produced.  
adjust zoom and focus  
adjust lens shift  
If the image is not on the screen or viewing area, adjust it by using the lens  
shift dials inside the lens door.  
Use the right dial to shift the lens left or right. Use the left dial to shift the  
lens up or down.  
adjust Contrast or Brightness  
contrast  
brightness  
Adjust the Contrast or Brightness in the Picture menu.  
See page 27 for help with the menus.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a video device  
Standard video connections  
connect A/V cable  
Plug the audio/video (A/V) cable’s yellow connector into the video-out  
connector on the video device. Plug the other yellow connector into the yel-  
low Video 3 connector on the projector. Plug a white connector into the left  
audio out connector on the video device and plug a red connector into the  
right audio out connector on the video device. Plug the remaining white  
connector into a left audio in connector on the projector, and plug the red  
connector into a right audio in connector on the projector. You can assign a  
particular source to a particular audio in connector, see page 31.  
connect power cable  
Connect the black power cable to the connector on the back of the projector  
and to your electrical outlet.  
NOTE: Always use the power cable that shipped with the projector.  
Optional video connections  
If the video device uses a round, four-prong S-video connector, plug an  
S-video cable (sold separately) into the S-video connector on the video  
device and into the Video 2 connector on the projector. Use the A/V cable’s  
audio connectors as described directly above (the yellow connectors on the  
A/V cable are not used).  
connect S-video and video cables  
If the video device uses component cable connectors (sold separately), plug  
the cable’s green connectors into the green component-out connector on the  
video device and into the Video 1 green component connector (labeled “Y”)  
on the projector. Plug the component cable’s blue connectors into the blue  
component-out connector on the video device and into the blue component  
connector (labeled “Cb/Pb”) on the projector. Plug the component cable’s  
red connectors into the red component-out connector on the video device  
and into the red component connector (labeled “Cr/Pr”) on the projector.  
Use the A/V cable’s audio connectors as described above (the yellow con-  
nectors on the A/V cable are not used). NOTE: The component connectors  
can be used for HDTV sources (480i, 480p, 720p, 576i and 1080i formats).  
connect component cables  
and video cables  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Displaying a video image  
Remove the lens cap.  
remove lens cap  
Press the power switch on the back of the projector to the on (I) position.  
The Power light on the Status Indicator Panel (page 15) lights green.  
press Power switch  
press Power button  
Press the Power button on the top of the projector or the remote.  
2
The Power light blinks green and the fans start to run. When the lamp  
comes on, the startup screen is displayed and the light is steady green. It can  
take a minute for the image to achieve full brightness.  
1
? No startup screen? Get help on page 16.  
Plug in and turn on the video device.  
turn on video device  
The video device’s image should appear on the projection screen. If it  
doesn’t, press the Source button on the keypad or remote.  
adjust height  
release  
button  
release  
button  
Adjust the height of the projector, if necessary, by pressing the release but-  
tons on each side of the projector’s front to extend the elevator feet. Rotate  
the feet, if necessary, to level the projector.  
elevator  
foot  
elevator  
foot  
adjust distance  
Position the projector the desired distance from the screen at a 90 degree  
angle to the screen. See page 39 for a table listing screen sizes and distances  
to the screen.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjust the zoom or focus by rotating the Zoom or Focus rings inside the  
lens door until the desired image size and focus are produced.  
adjust Zoom and Focus  
If the image is not on the screen or viewing area, adjust it by using the lens  
shift dials inside the lens door.  
adjust Lens Shift  
Use the right dial to shift the lens left or right. Use the left dial to shift the  
lens up or down.  
adjust volume  
Adjust the volume in the Audio menu.  
adjust Picture menu  
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.  
See page 27 for help with the menus.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Status Indicator Panel on top of the projector indicates the state of the  
projector and can help you troubleshoot.  
Shutting down the projector  
The projector automatically blanks the screen after no active source is  
detected for 5 minutes. This blank screen helps preserve the life of the pro-  
jector. The image returns when an active source is detected or a remote or  
keypad button is pressed.  
Screen Save  
Table 1: Status indicator light behavior and meaning  
You can make the blank screen appear after five minutes by turning on  
Screen Save in the Settings>System menu. See page 32.  
Status Indicator Panel icons  
Meaning  
Power Save  
Power, solid green  
The power button has been pressed and  
the software has initialized or the projec-  
tor has been powered off.  
The projector also has a Power Save feature that automatically turns the  
lamp off after no signals are detected for 20 minutes. After 10 additional  
minutes with no signal, the projector powers down. If an active signal is  
received before the projector powers down, the image is displayed. You  
must press the Power button to display an image after 30 minutes have  
passed. When Power Save is enabled, Screen Save is disabled. See page 32.  
Power, blinking green  
Thermometer  
The power button has been pressed and  
the software is initializing, or the projec-  
tor is powering down and the fans are  
running to cool the lamp.  
Turning off the projector  
To turn off the projector, press the power button and verify that you want to  
turn the projector off by pressing the power button again within 3 seconds.  
You can cancel the shutdown by not pressing the power button a second  
time. The lamp turns off and the Power light blinks green for over 1 minute  
while the fans continue to run to cool the lamp. When the lamp has cooled,  
the Power light is solid green and the fans stop. Press the power switch on  
the back of the projector and unplug the power cable to completely power  
off the projector.  
The projector is too hot. Make sure the  
vents aren’t blocked (see page 20). Turn  
off the projector and wait one minute,  
then turn the projector on again. Contact  
Technical Support if the problem persists.  
Lamp  
Turn off the projector and wait one  
minute, then turn the projector on again.  
If the lamp light turns on again, replace the  
lamp and reset the lamp timer.  
Troubleshooting your setup  
If your image appears correctly on the screen, skip to the next section. If it  
does not, troubleshoot the setup.  
Wrench/Service  
Turn off the projector and wait one  
minute, then turn the projector on again.  
If the service lamp turns on again, service  
is required. Visit our website to contact  
Service.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem  
Solution  
Result  
Plug power cable in, press power switch and  
power button. Remove lens cap.  
No startup screen  
Correct image  
3
startup  
screen  
2
1
Computer image projected  
Only startup screen appears/no computer image  
Press the Source button  
Activate laptop’s external port  
A
A
A
or restart  
laptop  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer image projected  
Adjust computer refresh rate in Control  
Panel>Display>Settings>Advanced>  
Adapter (location varies by operating  
system)  
No computer image, just the words “Signal out of  
range”  
Signal  
range  
out  
of  
A
A
A
You may also need to set a different  
resolution on your computer, as shown  
in the following problem, “Image fuzzy  
or cropped”  
Set your computer’s display resolution to  
the native resolution of the projector  
(Start>Settings>Control  
Panel>Display>Settings tab,  
select1024x768)  
Image clear and not cropped  
Image fuzzy or cropped  
A
A
A
For a laptop,  
disable laptop  
monitor  
or turn-on dual-  
display mode  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projector troubleshooting  
Problem  
Solution  
Result  
Square image  
Image not square  
Adjust keystone the Picture menu  
Correct image  
Adjust the focus ring or Sharpness in the  
Picture>Advanced menu  
Image not sharp  
A B  
A B  
Change aspect ratio to 16:9 in  
Picture>Aspect ratio menu  
Correct image  
Image does not fit 16:9 screen  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turn on/off Ceiling in Settings>System  
menu  
Correct image  
Image upside down  
B
A
A B  
Image reversed left to right  
Turn on/off Rear in Settings>System menu  
Correct image  
A
A B  
Correct image  
Projected colors don’t match source  
Adjust color, tint, color temperature,  
brightness, contrast in the menus  
COLOR  
COLOR  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Make sure vents aren’t blocked; allow  
projector to cool for one minute  
Unplug projector; wait 20 minutes; plug in  
projector and turn it on: lamp lights  
Lamp won’t turn on, Temp light is lit (page 15)  
Temperature light  
startup  
screen  
Lamp may need to be replaced (page 36)  
Lamp won’t turn on, Lamp light is lit (page 15)  
Lamp turns on  
Lamp light  
startup  
screen  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Correct image  
Move projector, adjust zoom or lens shift,  
adjust height  
Image not centered on screen  
Adjust horizontal or vertical position in  
Picture>Advanced menu  
Still having problems?  
If you need assistance, visit our website or call us. See the inside of the back cover for a list of all relevant web addresses.  
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we  
recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its  
full value.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the keypad buttons  
power–turns the projector on (page 10) and off (page 15).  
menu–opens the on-screen menus (page 27).  
up/down arrows–navigates to and adjusts settings in the menus (page 27).  
select–confirms choices made in the menus (page 27).  
source–switches among active sources  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LED  
navigation buttons  
Using the remote control  
laser  
button  
The remote uses two (2) provided AAA batteries (Hitachi Maxell, part num-  
ber LR03). They are easily installed by sliding the cover off the remote's  
back, aligning the + and - ends of the batteries, sliding them into place, and  
then replacing the cover.  
To operate, point the remote at the projection screen or at the projector (not  
at the computer). The range of optimum operation is about 16 feet (5m).For  
best results, aim the remote directly at the projector.  
backlight button  
source buttons  
To use the laser pointer, press and hold the Laser button. The laser turns off  
when the button is released, or times out after two (2) minutes of continu-  
ous operation.  
WARNING: Do not look into the laser beam emitted from the top of the  
remote control.  
The remote contains four Source buttons that allow you to assign a particu-  
lar input to a specific source. Simply press the numbered Source buttons to  
travel to whatever four sources you wish to have available.  
Troubleshooting the remote  
Make sure the batteries are installed in the proper orientation and are  
not dead. The LED at the top of the remote lights when any button is  
pressed when the battery power is adequate.  
Press the remote's Menu button to open the projector's menu system. Use  
the arrow buttons to navigate, and the Select button to select features and  
adjust values in the menus.  
Make sure you’re pointing the remote at the projector, not the com-  
puter, and are within the remote range of 16 feet (5m).  
The remote also has a power button to turn the projector on and off, volume  
buttons and a mute button to control the sound, a backlight button to light  
the remote's buttons in the dark, and a video and computer button to switch  
between those two sources.  
Two presentation-specific features are also provided. Use the blank button  
to display a blank screen instead of the current slide; use the effect button to  
invoke a user-definable action, such as freeze, PiP, or magnify.  
The Auto Image button reacquires the computer image and the Presets but-  
ton lets you customize the settings for each source. Up to three Preset set-  
tings can be customized and saved.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the audio  
connect audio cable  
To play sound from the projector, connect your source to an Audio In con-  
nector on the projector.  
To adjust the volume, mute, or loudness, use the Audio menu (see page 31).  
Troubleshooting audio  
If there is no sound, check the following:  
Make sure the audio cable is connected.  
Make sure mute isn’t active.  
adjust volume  
Make sure the volume is turned up enough.  
Make sure you are connected to the corresponding audio in for your  
source. By default, Audio 1 corresponds to Computer 2, Audio 2 cor-  
responds to Computer 3, Audio 3 corresponds to Video 2 and 3, and  
Audio 4 corresponds to Video 1. You can change these assignments,  
see page 31.  
Adjust the audio source.  
If playing a video, make sure the playback has not been paused.  
Connecting external speakers  
The projector can be attached to external speakers that have their own  
power source by plugging a speaker cable into the projector’s Audio Out  
connector.  
external speakers  
speaker  
cable  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optimizing computer images  
Presentation features  
After your computer is connected properly and the computer’s image is on  
the screen, you can optimize the image using the onscreen menus. For gen-  
eral information on using the menus, see page 27.  
Several features are provided to make giving presentation easier. The fol-  
lowing is an overview, details are found in the menu section on page 27.  
The Custom key, available on several optional remotes only, allows  
you to assign various features to the key. The default effect is Source  
Info. You can select from Blank, Mute, AV Mute, Aspect Ratio, Source,  
Auto Image, Freeze, Magnify, Source Info, and Service Info. See page 33  
for details.  
Adjust the Keystone, Contrast, or Brightness in the Picture menu.  
Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to  
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV  
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your  
input source. See page 28 for details.  
The Freeze effect allows you to freeze the displayed image. This is use-  
ful if you want to make changes on your computer without your audi-  
ence seeing them.  
Adjust the Color Temperature in the Advanced menu.  
Adjust the Phase, Tracking, or Horizontal or Vertical position in the  
Advanced menu.  
The Startup Logo menu option lets you change the default startup  
screen to a black, white, blue, or a custom logo screen via Capture New.  
See page 32.  
Once you have optimized the image for a particular source, you can  
save the settings using Presets. This allows you to quickly recall these  
settings later. See page 29.  
Two menu options, Power Save and Screen Save, are provided to auto-  
matically shut down the projector after several minutes of inactivity or  
display a blank screen. This helps preserve lamp life. See page 32.  
A Low Power menu option is also available to help lower the projec-  
tor’s fan sound volume. See page 31.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optimizing video images  
Customizing the projector  
After the video device is connected properly and the image is on the screen,  
you can optimize the image using the onscreen menus. For general informa-  
tion on using the menus, see page 27.  
You can customize the projector for your specific setup and needs. See  
page 31 to page 34 for details on these features.  
For rear projection, turn Rear mode on in the Settings>System menu.  
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture  
menu. See page 28.  
For ceiling mounted projection, turn Ceiling mode on in the Set-  
tings>System menu.  
Change the Aspect ratio. Aspect ratio is the ratio of the image width to  
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV  
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your  
input source. See page 28.  
Specify which source the projector checks first for an active signal dur-  
ing power-up.  
Turn the projector’s on-screen display messages on and off.  
Turn on power saving features.  
Select a Sharpness setting. See page 29.  
Specify blank screen colors and startup logos.  
Specify the menu language.  
Adjust the Color Temperature. Select a listed value, or select User and  
individually adjust the intensity of the red, green, and blue color. See  
page 29.  
Control your projector using RS232 commands. See page 9 and page 42.  
Customize the projector for your specific installation using optional  
long or short throw lenses. See the inside back cover of this User’s  
Guide for ordering information.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the menus  
To open the menus, press the menu button on the keypad or remote. (The  
menus automatically close after 60 seconds if no buttons are pressed.) The  
Main menu appears. Use the arrow buttons to move up and down to high-  
light the desired submenu, then press the Select button.  
Menu  
button  
To change a menu setting, highlight it, press Select, then use the up and  
down arrow buttons to adjust the value, select an option using radio but-  
tons, or turn the feature on or off using check boxes. Press Select to confirm  
your changes. Use the arrows to navigate to another setting. When your  
adjustments are complete, navigate to Previous, then press Select to go to  
the previous menu; press the Menu button at any time to close the menus.  
Keypad navigation  
buttons  
Main menu  
Dots appear before the menu name. The number of dots indicate the menu’s  
level, ranging from one (the Main menu) to five (the most nested menus).  
Dots  
The menus are grouped by usage:  
The Picture menu provides image adjustments.  
The Settings menu provides set-up type adjustments that are not  
changed often.  
The Source Info menu provides a read-only display of information  
about the projector and source.  
Settings  
menu  
Picture  
menu  
Certain menu items may be grayed out until a particular source is con-  
nected. For example, Tint is only available for video sources and will be hid-  
den when a computer source is active. Other menu items may be grayed out  
when they are not available. For example, Brightness is grayed out until an  
image is active.  
Source Info menu  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture menu  
To adjust the following six settings, highlight the setting, press Select, use  
the up and down arrows to adjust the values, then press select to confirm  
the changes.  
Keystone Vertical  
increasing keystone  
decreasing keystone  
Keystone Vertical: adjusts the image vertically and makes a squarer image  
by using an adjustable scale band.  
Keystone Horizontal: adjusts the image horizontally and makes a squarer  
image by using an adjustable scale band.  
Contrast: controls the degree of difference between the lightest and darkest  
parts of the picture and changes the amount of black and white in the  
image.  
Keystone Horizontal  
Brightness: changes the intensity of the image.  
Color: (Computer 1 and video sources only) adjusts a video image from  
black and white to fully saturated color.  
Tint: (Computer 1 and NTSC video sources only) adjusts the red-green  
color balance in the image.  
Auto Image: resynchs the projector to the source.  
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.  
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are  
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or  
down to fill the display area.  
Aspect Ratio  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Presets: Presets are provided that optimize the projector for displaying  
computer presentations and video images in different lighting conditions  
and on different backgrounds.  
There are also user-definable presets. To set a preset for the current source,  
adjust the image, select Save Settings in the Presets menu, then select Save  
User Presets 1 (or 2 or 3). You can recall these settings in the future by select-  
ing the User 1 preset. If you select User Presets then further adjust the  
image, Presets Off will automatically be selected in the Preset menu to indi-  
cate changes have been made.  
Save Settings  
To restore the factory default settings, choose Factory Reset in the Set-  
tings>Service menu.  
Presets  
Advanced settings  
Sharpness: changes the clarity of the edges of a video image. Select a sharp-  
ness setting.  
Color Space: This option applies to computer and component video  
sources (except 480i/576i). It allows you to select a color space that has been  
specifically tuned for the input signal. When Auto is selected, the projector  
automatically determines the standard. To choose a different setting, turn  
off Auto, then choose RGB for computer sources, RGB Video for HDMI  
computer sources, and either REC709 or REC601 for component video  
sources.  
Sharpness  
Color Temperature: changes the intensity of the colors. Select a listed  
value, or select User and individually adjust the intensity of the red, green,  
and blue colors.  
Color Space  
Color Temperature  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Standard: when set to Auto, the projector attempts to automatically  
pick the video standard based on the input signal it receives. (The video  
standard options may vary depending on your region of the world.) If the  
projector is unable to detect the correct standard, the colors may not look  
right or the image may appear “torn.” If this happens, manually select a  
video standard by selecting NTSC, PAL, or SECAM from the Video Stan-  
dard menu.  
.
Video Standard  
Active Iris  
Active Iris: when on, the projector monitors the image brightness and mod-  
ifies the light output if the image is dark, which improves black levels. In  
Presentation mode, it looks at peak brightness, in Theater mode it looks at  
average brightness.  
Overscan: (Computer 1 and video sources only) removes noise around the  
video image.  
The following 4 options are for computer sources only:  
Phase: adjusts the horizontal phase of computer 2, 3 and component (except  
480i and 576i) sources.  
Tracking: adjusts the horizontal scan of a computer source (except Com-  
puter 1).  
Horizontal / Vertical Position: adjusts the position of a computer source  
(except Computer 1) and Video 1 source (except 480i and 576i).  
Computer 2  
Computer 3  
Computer 2: allows you to turn Sync on Green on for this source.  
Computer 3: allows you to turn Sync on Green on for this source.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PC Screen Saver Off: prevents your notebook computer from going into  
Screen Save mode. The projector must be connected to the PC via a USB  
cable for this feature to work.  
Settings menu  
Audio: allows adjustments to the volume. Also allows you to turn on and  
off the Internal speakers and assign a particular source to a specific audio  
input. If your HDMI source has problems with its audio stream, you can  
mute it by selecting HDMI Noise Cancel.  
Settings  
menu  
Sources: allows you to assign a particular input to a specific source key  
when using the remote. Also allows selection of a default Startup Source  
and enables or disables Autosource.  
Audio  
Sources>Power-up Source: this determines which source the projector  
checks first for active signal during power-up.  
Sources>Autosource: When Autosource is not checked, the projector  
defaults to the source selected in Powerup Source. If no source is found, a  
blank screen displays. When Autosource is checked, Powerup Source deter-  
mines which source the projector defaults to at power-up. If no signal is  
present, the projector checks the sources in order until a source is found or  
until power down.  
System>Rear: reverses the image so you can project from behind a  
translucent screen.  
Ceiling: turns the image upside down for ceiling-mounted projection.  
WARNING: To prevent eye injury if the projector is ceiling mounted,  
wear protective eyewear before opening lamp door. A warning sticker is  
included with the user documentation. Place this sticker on the lamp  
door if the projector is mounted on the ceiling.  
Powerup  
Source  
Sources  
IR Receivers: turns individual IR receivers off or on to avoid environ-  
mental interference.  
Auto Power: When Auto Power is checked, the projector automatically  
goes into the startup state after the projector is powered on. This allows  
control of ceiling mounted projectors with a wall power switch.  
Display Messages: displays status messages (such as “Searching”) in the  
lower-left corner of the screen.  
Low Power: toggles between on and off. Turn it on to lower the light out-  
put of the lamp. This also lowers the fan speed, making the projector qui-  
eter.  
IR Receivers  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Power Save: automatically turns the lamp off after no signals are  
detected for 20 minutes. After 10 additional minutes with no signal, the  
projector powers down. If an active signal is received before the projec-  
tor powers down, the image will be displayed.  
Screen Save  
Screen Save: automatically blanks the screen after no signals are  
detected for five minutes. The image returns when an active source is  
detected or a remote or keypad button is pressed. Screen Save is disabled  
when Power Save is enabled.  
Startup Logo: allows you to display a blank Black, White, or Blue screen  
instead of the default screen when no source is detected at startup. It also  
allows you to capture and display a custom startup screen.  
To capture a custom logo, display the image you want to capture on your  
computer and select the Capture New option. From the Capture New  
menu, use the Capture Position X and Capture Position Y adjustments to  
frame the logo to be captured. Press Capture Start in the Capture New  
menu. The projector will let you know if the capture was a success or a  
failure.  
Capture New  
Startup Logo  
The next time you start the projector, the custom logo you captured dis-  
plays.  
Blank Screen  
Blank Screen: determines what color is displayed when you press the  
Blank button on an optional remote.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Custom Key (for use with optional remote only): allows you to assign a dif-  
ferent function to the Custom key on the optional remote to quickly and  
easily use the effect. Only one effect can be enabled at a time. The default is  
Source Info; highlight an effect and press Select to choose a different one.  
Network Restart: Disconnects the projector from the network, gets a  
new IP address, and reconnects.  
Network Info: Provides information on the network configuration.  
Blank: shows an empty screen.  
Mute: turns off all sound.  
AV Mute: turns off all sound and displays a blank screen.  
Aspect Ratio: sets the ratio of the image width to image height.  
Source: cycles through the available sources.  
Auto Image: causes all sources to be reacquired.  
Freeze: pauses the projected image.  
Custom Key  
Magnify: allows you to enlarge a section of the projected image.  
Source Info: displays the Source Info menu.  
Service Info: displays the Service Info menu.  
Network: The projector has an RJ45 Ethernet connector that supports net-  
work connections and TCP/IP protocols. This will allow for the control and  
management of the projector over a corporate network. Visit our website for  
complete details on using the networking functionality. The following fields  
are accessible when DHCP is not checked and available for manual entry of  
data.  
Network  
IP Address: Identifies the projector on the network.  
Subnet Mask: Separates the network address part of the IP address.  
Default Gateway: The IP address of the local router.  
DNS Server: Shows the address of the DNS server.  
Network  
Info  
DHCP: Select this to automatically obtain an IP address, Subnet mask,  
and Default gateway.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Language: allows you to select a language for the onscreen display of  
menus and messages.  
Language  
Service: to use these features, highlight them and press Select.  
Factory Reset: restores all settings (except Lamp and Filter Hours and Net-  
work settings) to their default after displaying a confirmation dialog box.  
Reset Lamp Hours: resets the lamp hours counter in the Service Info menu  
to zero. Do this only after changing the lamp. It displays a confirmation dia-  
log box.  
Reset Filter Hours: resets the filter counter in the Service Info menu to  
zero. Do this only after cleaning the filter. It displays a confirmation dialog  
box.  
Lens Type: change this setting only if you purchase an optional lens. The  
projector customizes its keystone settings based on the lens used. Select  
your optional lens from the menu. A sticker containing a number between 1  
and 5 is attached to the lens to help you identify which type of lens you pur-  
chased.  
Lens Type  
Service menu  
Service Info: provides information for service.  
Service Code: only used by authorized service personnel.  
Service Info  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
clean the lens  
with a soft dry cloth  
and non-abrasive  
cleaner  
Cleaning the lens  
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.  
Avoid using an excessive amount of cleaner, and don’t apply the  
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh  
chemicals might scratch the lens.  
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you  
don’t intend to use the projector immediately, replace the lens cap.  
turn off and unplug  
the projector  
Replacing the clock batteries  
The projector has a lithium Hitachi Maxell battery (part number CR2032) on  
the bottom that is used to power the clock used for networking applications.  
Visit our website for complete details on using the networking functionality.  
wait 45 minutes  
1 Turn off the projector and unplug the power cable.  
open battery cover  
2 Wait 45 minutes to allow the projector to cool thoroughly.  
3 Turn the projector upside down and use a coin to turn the battery cover  
12'0  
to the “Open” position.  
4 Remove the battery and dispose of in an environmentally proper man-  
ner.  
5 Install a new battery with the “+” side facing up.  
%.15'  
6 Press the battery into place, then replace the battery cover.  
install new battery,  
+ side up  
NOTE: The clock time will need to be reset in the web browser application  
after replacing the battery.  
press battery into position  
close battery cover  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
the lamp compartment and dispose of cleaning materials. Wash hands  
after lamp replacement.  
Hg – Lamp contains mercury. Manage in accordance with local  
disposal laws. See www.lamprecycle.org.  
Replacing the projection lamp  
The lamp hour timer in the Service Info menu counts the number of hours  
the lamp has been in use. Twenty hours before the specified end of the  
lamp’s life, the message “Change lamp” briefly appears on the projected  
screen.  
NOTE: You can order new lamp housings from www.infocus.com (in select  
areas), your retailer or your dealer. Only genuine InFocus lamps are tested  
for use in this projector. InFocus is not liable for the performance, safety or  
certification of any other lamps. The use of other lamps violates the projec-  
tor warranty and voids all certification marks on this projector.  
lamp hours  
1 Turn off the projector and unplug the power cable.  
2 Wait 45 minutes to allow the projector to cool thoroughly.  
turn off and unplug  
the projector  
3 Loosen the lamp cover screw on the right side of the projector (marked  
by the arrow) then slide and lift the lamp cover off.  
WARNINGS:  
wait 45 minutes  
To avoid burns, allow the projector to cool for at least 45 minutes before  
you replace the lamp.  
Only genuine InFocus lamps are tested with this projector. Use of other  
lamps may cause electrical shock and fire.  
To prevent eye injury if the projector is ceiling mounted, wear protec-  
tive eyewear before opening lamp door. A warning sticker is included  
with the user documentation. Place this sticker on the lamp door if the  
projector is mounted on the ceiling.  
Do not drop the lamp module. The glass may shatter and cause injury.  
Do not touch the glass lamp screen. Fingerprints can obscure projection  
sharpness.  
lamp cover screw  
Be extremely careful when removing the lamp housing. In the unlikely  
event that the bulb ruptures, small glass fragments may be generated.  
The lamp housing is designed to contain these fragments, but use cau-  
tion when removing the lamp housing. Before replacing the lamp, clean  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4 Loosen the three captive screws (marked by the arrows) on the lamp  
module. When replacing the lamp, never touch any screws without the  
arrow mark.  
loosen the captive screws on lamp module  
5 Carefully remove the lamp module by grasping and lifting the handle.  
lamp module handle  
Dispose of the lamp in an environmentally proper manner.  
6 Install the new lamp module, making sure that it is properly seated, and  
tighten the three captive screws.  
7 Replace the cover over the lamp module by sliding it back into place and  
tightening the screw.  
8 Plug in the power cable, press the power switch then press the Power  
button to turn the projector back on. Reset the lamp hour timer by navi-  
gating to the Settings>Service menu and selecting Reset Lamp Hours.  
reset lamp hours in Service menu  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning the dust filter  
1 Turn off the projector and unplug the power cable.  
2 Wait 45 minutes to allow the projector to cool thoroughly.  
WARNING: To avoid burns, allow the projector to cool for at least 45  
minutes before you clean or replace the dust filter.  
wait 45 minutes  
3 Remove the dust filter cover on the side of the projector by pressing up  
on the two tabs at the cover’s bottom.  
4 Pull the tab on the center of the black dust filter bracket and lift it off.  
5 Clean the filter, cover, and vent using a vacuum set on low power.  
Replace the filter if it is damaged or too dirty to clean.  
6 Replace the dust filter and the bracket on the cover, then replace the dust  
filter cover.  
7 Reset the filter hour timer by navigating to the Settings>Service menu  
and selecting Reset Filter Hours.  
dust filter cover  
tabs  
reset filter hours in Service menu  
Using the security lock  
The projector has a security lock for use with a cable lock system. See the  
Accessories catalog that came with the projector, or visit our website, for  
ordering information. Refer to the information that came with the lock for  
instructions on how to use it.  
security lock  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional lenses  
Appendix  
WARNING: When replacing the lens, turn off the projector and pull out the  
power cord from the receptacle. Loosen the screws marked with a triangle  
to remove the lens.  
Projected image size  
NOTE: Visit the Service section of our website for interactive image size cal-  
culators for the standard and optional lenses.  
NOTE: You can order optional lenses from www.infocus.com (in select  
areas), your retailer or your dealer.  
Table 2: Projection sizes: Standard lens (1.5 - 1.8:1 throw ratio)  
Table 3: Projection sizes: Short Fixed lens (0.8:1 throw ratio)  
Minimum Image  
Maximum Image  
Projection Distance  
(inch/m)  
Diagonal  
Image  
(feet/m)  
Image  
Width  
(feet/m)  
Diagonal  
Image  
(feet/m)  
Image  
Width  
(feet/m)  
Distance  
(feet/m)  
Screen Size (inch/m)  
40/1  
Minimum  
24/0.6  
Min Distance  
2.1/0.66  
1.7/0.53  
2.6/0.79  
2.1/0.63  
3/0.9  
60/1.5  
35/0.9  
5/1.5  
3.5/1.1  
7.0/2.1  
2.8/0.86  
5.6  
4.2/1.3  
1.7  
3.4/1.0  
8.3/2.5  
10/3  
70/1.8  
43/1.1  
10/3.0  
15/4.6  
20/6.1  
25/7.6  
100/2.5  
63/1.6  
10.4/3.2  
13.8/4.2  
17.2/7.6  
20.6/6.3  
8.3/2.5  
11/3.4  
13.8/4.2  
16.5/5  
12.5/3.8  
16.6/5.1  
20.7/6.3  
24.8/7.6  
120/3  
75/1.9  
13.3/4  
16.6/5  
19.8/6.1  
150/3.8  
94/2.4  
200/5.1  
130/3.3  
161/4.1  
193/4.9  
224/5.7  
Max Distance  
30/9.1  
250/6.4  
300/7.6  
The image offset range for the standard lens is 9:1 (90%) to 1:1 (50%).  
350/8.9  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 4: Projection sizes: Short Zoom lens (1.2 -2.0:1 throw ratio range)  
Projection Distance (inch/m)  
Table 5: Projection sizes: Long Throw lens (1.9 - 3.9:1 throw ratio range  
Projection Distance (inch/m)  
Screen Size  
(inch/m)  
Screen Size  
(inch/m)  
Minimum  
39/1.0  
Maximum  
63/1.6  
Minimum  
59/1.5  
Maximum  
122/3.1  
40/1  
60/1.5  
40/1  
60/1.5  
59/1.5  
94/2.4  
94/2.4  
185/4.7  
70/1.8  
67/1.7  
110/2.8  
157/4.0  
189/4.8  
240/6.1  
319/8.1  
402/10.2  
480/12.2  
559/14.2  
70/1.8  
110/2.8  
157/4.0  
189/4.8  
236/6.0  
319/8.1  
402/12.2  
480/16.3  
642/20.4  
803/20.4  
217/5.5  
100/2.5  
120/3  
98/2.5  
100/2.5  
120/3  
311/7.9  
118/3.0  
150/3.8  
197/5.0  
248/6.3  
299/7.6  
350/8.9  
374/9.5  
150/3.8  
200/5.1  
250/6.4  
300/7.6  
350/8.9  
150/3.8  
200/5.1  
250/6.4  
300/7.6  
400/10.2  
500/12.7  
467/11.9  
630/16.0  
787/23.9  
94532.0  
126040.1  
1579/40.1  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6: Projection sizes: Ultra Long Throw lens (3.9 - 7.4:1 throw ratio  
range  
Projection Distance (inch/m)  
Screen Size  
(inch/m)  
40/1  
Minimum  
122/3.1  
Maximum  
236/6.0  
60/1.5  
70/1.8  
189/4.8  
354/9.0  
220/5.6  
513/10.5  
594/15.1  
717/18.2  
898/22.8  
1197/30.4  
1496/45.6  
1795/53.3  
2398/60.9  
3000/76.2  
100/2.5  
120/3  
315/8.0  
382/9.7  
150/3.8  
200/5.1  
250/6.4  
300/7.6  
400/10.2  
500/12.7  
476/12.1  
638/16.2  
799/24.4  
961/28.5  
1283/32.6  
1602/40.7  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A read command returns the range and the current setting, for example:  
RS-232 commands  
Communication Configuration  
Visit our website for additional RS-232 settings and information.  
Read Command Examples  
Function  
Brightness  
Volume  
Command  
(BRT?)  
Response  
(96-160,128)  
(0-32, 0)  
To control this projector via RS-232, connect a null modem cable and set the  
control system serial port settings to match the following communication  
configuration:  
(VOL?)  
RS-232 Port Settings  
Lamp Hours  
(LMP?)  
(0-32766, 42)  
Setting  
Value  
19,200  
8
A write request example:  
(AAA####) where  
Bits per second  
Data bits  
(starts the command  
Parity  
None  
1
AAA denotes the command  
#### denotes the value to be written  
(leading zeros not necessary)  
) ends the command  
Stop bits  
Flow control  
Emulation  
None  
VT100  
Some commands have ranges, while others are absolute. If a number greater  
than the maximum range is received, it is automatically set to the maximum  
number for that function. If a command is received that is not understood, a  
"?" is returned. With absolute settings, "0" is off, 1-9999 is on. The one excep-  
tion is the Power command, where 0 is off and 1 is on.  
Command Format  
All commands consist of 3 alpha characters followed by a request, all  
enclosed in parentheses. The request can be a read request (indicated by a  
"?") or a write request (indicated by 1 to 4 ASCII digits).  
A read request example:  
(AAA?) where  
To assure the projector can process a command, wait 3 seconds before enter-  
ing the next command.  
(starts the command  
AAA denotes the command  
? denotes the read request  
) ends the command  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Write Command Examples  
St  
e
p
Com-  
mand  
Function  
Min Max  
Default  
Function  
Brightness  
Power  
Command  
(BRT140)  
(PWR0)  
Response  
Sets the brightness to 140  
Turns power off  
About (Source Info)  
0: n/a  
1: enable  
ABT at W  
0
0
1
2
n/a  
Power  
(PWR1)  
Turns power on  
Active Iris  
0: Off  
1: Presentation  
2: Film  
IRI at RW  
1
2
Error Conditions  
Not all commands are supported for all projectors. If an unsupported com-  
mand is issued, the command will be ignored. If a command is received that  
is not understood, a ‘?’ character will be returned indicating the command  
was not understood.  
Aspect Ratio  
0: Native  
1: 16:9  
ARZ at RW  
0
2
Limitations  
2: 4:3  
The projector cannot respond to commands coming in at a high-rate. There-  
fore, a delay must occur between commands to ensure that the command  
gets properly executed. To assure the projector can process a command,  
wait 3 seconds before entering the next command.  
Auto Image  
0: n/a  
1: enable  
AIM at W  
0
0
0
0
1
1
1
1
n/a  
0
Auto Power  
0: disable  
1: enable  
APO at RW  
ASC at RW  
BLK at RW  
The Step column refers to increasing or decreasing the menu bar position  
since the On-screen Display is not an exact match of values. For example,  
Step 2 changes the data by 2 through the CLI (Command Line Interface).  
The menu bar is up (or down) by 1.  
Auto Source  
0: disable  
1: enable  
1
Blank  
0: off  
1: on  
0
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blank Screen  
0: black  
BSC at RW  
0
2
1
Custom Key (Effect)  
0: blank  
EFK at RW  
0
15  
7
1: blue  
1: mute  
2: white  
2: aspect ratio  
3: source  
4: auto image  
5: freeze  
Blue Gain  
Brightness  
BCG at RW  
BRT at RW  
CEL at RW  
64  
96  
0
192  
160  
1
128  
128  
0
1
1
6: zoom  
7: Source Info  
8: Service Info  
15: AV Mute  
Ceiling  
0: disable  
1: enable  
Display Messages  
0: disable  
1: enable  
DMG at RW  
RST at W  
0
0
0
1
1
1
1
Color  
CLR at RW  
CSM at RW  
96  
0
160  
4
128  
0
1
Color Space  
0: Auto  
1: RGB  
2: REC709  
3: REC601  
4: RGB Video  
Factory Reset  
0: not reset  
1: reset  
n/a  
0
Freeze  
FRZ at RW  
0: disable  
1: enable  
Color Temp  
0: 9300K  
1: 6500K  
2: 7200K  
3: User  
TMP at RW  
CON at RW  
0
3
2 (computer  
2,3)  
0 (other)  
Green Gain  
GCG at RW  
DKH at RW  
HNC at RW  
HPS at RW  
64  
38  
0
192  
218  
1
128  
128  
1
1
1
Horizontal Keystone  
HDMI Noise Cancel  
Horizontal Position  
Contrast  
96  
160  
128  
1
def:-  
128  
def:+1 auto  
28  
1
Internal Sound Enable INT at RW  
0
1
1
0: disable  
1: enable  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IR Receiver front  
0: disable  
1: enable  
IRF at RW  
IRR at RW  
IRT at RW  
LAN at RW  
0
0
0
0
1
1
1
0
0
Lamp Lit  
0: not lit  
1: lit  
LML at R  
LRT at W  
0
0
1
IR Receiver rear  
0: disable  
1: enable  
1
Reset Lamp Hours  
0: not reset  
1: reset  
1
n/a  
IR Receiver top  
0: disable  
1: enable  
1
Number of Lamp  
Resets  
LMR at R  
LMT at R  
LB1 at R  
LB2 at R  
LB3 at R  
LPE at RW  
0
0
0
0
0
0
32766  
0
0
0
0
0
0
Lamp Total On Time  
(All Bulbs)  
21474  
83646  
Language  
17  
0 = English  
1 = French  
2 = German  
3 = Italian  
5 = Korean  
6 = Norwegian  
7 = Portuguese  
8 = Russian  
9 = Simplified  
Chinese  
10 = Spanish  
11 = Traditional  
Chinese  
12 = Swedish  
13 = Dutch  
14 = Polish  
15 = Turkish  
16 = Danish  
17 = Finnish  
Time In Hours Last  
Bulb1 Lasted  
32766  
32766  
32766  
1
Time In Hours Last  
Bulb2 Lasted  
Time In Hours Last  
Bulb3 Lasted  
Low Power  
0: disable  
1: enable  
Magnify  
MAG at RW  
MGE at RW  
0
0
48  
1
0
0
1
Magnify Enable  
0: disable  
1: enable  
Magnify Position Hor- MPH at RW  
izontal  
0
0
64  
64  
32  
32  
1
1
Lamp Hours  
LMP at R  
0
32766  
0
1
Magnify Position Ver-  
tical  
MPV at RW  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
0: disable  
1: enable  
MNU at RW  
NAV at W  
0
0
1
4
0
Power-up Source  
0: computer 1  
1: computer 2  
2: computer 3  
3: video 1  
DSC at RW  
0
0
5
1
Menu Navigation  
0: up  
1: down  
n/a  
4: video 2  
5: video 3  
4: select  
Presets  
0: user 1  
1: user 2  
2: user 3  
3: Presets Off  
5: presentation  
7: video  
10: bright  
11: whiteboard  
PST at RW  
11  
computer  
2,3:5  
computer 1,  
video:7  
Mute  
0: disable  
1: enable  
MTE at RW  
NTR at W  
NND at RW  
0
0
0
1
1
1
0
Network Restart  
0: not restart  
1: restart  
n/a  
1
NND (PC Screen  
Saver Off)  
0: disable  
Rear  
0: disable  
1: enable  
REA at RW  
0
1
0
1: enable  
Overscan  
0: disable  
1: enable  
OVS at RW  
0
1
0
Red Gain  
RCG at RW  
FRT at W  
64  
0
192  
1
128  
n/a  
1
Reset Filter Hours  
0: not reset  
1: reset  
Phase  
MSS at RW  
0
0
31  
1
0
0
1
Power  
0: disable  
1: enable  
PWR at RW  
Save User Presets 1  
0: not saved  
1: saved  
US1 at W  
US2 at W  
0
0
1
1
n/a  
n/a  
Power Save  
0: disable  
1: enable  
PSV at RW  
0
1
0
Save User Presets 2  
0: not saved  
1: saved  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Save User Presets 3  
0: not saved  
1: saved  
US3 at W  
SSV at RW  
0
0
1
5
n/a  
0
Audio for Source 0  
0: audio 1  
1: audio 2  
2: audio 3  
3: audio 4  
SA0 at RW  
0
5
4
Screen Save  
0: 5 minutes  
1: 10 minutes  
2: 15 minutes  
3: 20 minutes  
4: 25 minutes  
5: 30 minutes  
4: HDMI Internal  
5: mute  
Audio for Source 1  
0: audio 1  
1: audio 2  
2: audio 3  
3: audio 4  
SA1 at RW  
0
0
5
2
0
1
3
2
2
Source 2:SA2  
Source 3:SA3  
Source 4:SA4  
Source 5:SA5  
Sharpness  
SHP at RW  
SRC at RW  
5
0
9
5
7 (computer  
and video 1)  
6 (video 2  
and 3)  
5 = Sharpest  
6 = Sharper  
7 = Standard  
8 = Softer  
5: mute  
Startup Logo  
0: blank screen  
1: default  
DSU at RW  
1
9 = Softest  
2: captured  
Source  
0
0: computer1  
1: computer2  
2: computer 3  
3: video 1  
Sync on Green  
0: Sunc on G off  
1: Auto  
SOG at RW  
0
1
1
4: video 2  
5: video 3  
Tint  
TNT at RW  
MTS at RW  
96  
160  
128  
1
1
Tracking  
def:  
-384  
def:  
+384  
auto  
Source 1  
SR1 at RW  
0
5
0
1
3
4
0: computer 1  
1: computer 2  
2: computer 3  
3: video 1  
Source 2:SR2  
Source 3:SR3  
Source 4:SR4  
4: video 2  
5: video 3  
Unit Total Time On  
Vertical Keystone  
ONL at R  
0
21474  
83646  
0
DKC at RW  
38  
218  
128  
1
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Vertical Position  
VPS at RW  
if  
def  
auto  
1
def<  
128:  
0
+128  
else:  
def -  
128  
Video Standard  
0: Auto  
1: NTSC  
2: PAL  
VSU at RW  
VOL at RW  
0
3
0
3: SECAM  
Volume  
0
32  
16  
1
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX  
Display Messages 31  
displaying  
Numerics  
1024x768 resolution 5  
A
Aspect Ratio 33  
audio 24  
Audio In connector 8, 12  
Auto Image 33  
Auto Power 31  
Autosource 31  
B
computer image 10  
video images 13  
dust filter, cleaning 38  
E
elevator foot 11, 13  
F
Factory Reset 34  
filter, resetting hours 34  
focus 11, 14  
Freeze 33  
Blank 33  
BNC 8  
fuzzy image 17  
H
Brightness 11  
HDMI 6  
C
HDTV sources 12  
I
image  
Capture Position 32  
Capture Start 32  
cleaning the dust filter 38  
cleaning the lens 35  
clock batteries 35  
Color 14  
colors are incorrect 19  
component cable connector 12  
computer connections  
optional 8  
display computer 10  
display video 13  
size 7  
image does not fit screen 18  
image not centered 21  
image not sharp 18  
image not square 18  
image reversed 19  
image size matrix 39  
image upside down 19  
IP Address 33  
IR Receivers 31  
L
required 8  
computer image  
displaying 10  
optimize 25  
connector panel 6  
contacting service 21  
Contrast 11, 14  
custom logo startup screen 32  
customer service contact information 21  
D
lamp hours, resetting 37  
lamp replacement 36  
lamp won’t turn on 20  
Language 34  
laptop  
Default gateway 33  
DHCP 33  
connecting 8  
external video port 10  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
lens, cleaning 35  
Low Power 31  
M
resetting lamp hours 37  
RS-232  
cable 9  
Magnify 33  
connecting 6  
S
screen saver, turning off 31  
security lock 38  
serial connection 6, 9  
Service 34  
Main menu 27  
menu system 27  
Monitor connector 9  
Mute 33  
N
Network 33  
Service Code 34  
Service Info 34  
Settings menu 31  
shutting down projector 15  
Source 33  
Source troubleshooting 16  
Sources 31  
Subnet mask 33  
S-video connector 12  
T
Tint 14  
troubleshooting 15, 16  
V
video connections  
optional 12  
Network connector 9  
Network Info 33  
no computer image 17  
no startup screen 16  
O
only startup screen appears 16  
Overscan 30  
P
PC Screen Saver Off 31  
Picture menu 28  
power cable 8, 12  
Power Save 32  
Power-up Source 31  
presentation features 25  
projection distance 7  
projector  
standard 12  
Video connector 12  
video image  
displaying 13  
video images  
optimizing 26  
Video Standard 30  
volume adjustment 14  
W
connector panel 6  
customizing 26  
height 11, 13  
positioning 7, 11, 13  
setting up 7  
shutdown 15  
troubleshooting problems 15  
R
Rear 31  
warranty 21  
X
remote control 23  
replacing the clock batteries 35  
replacing the lamp 36  
Reset Filter Hours 34  
XGA 5  
Z
zoom 11, 14  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  

InFocus Projector LS700 User Manual
Intel Outboard Motor LXD386 User Manual
Invacare Wheelchair 1141448 User Manual
IOGear Computer Drive GHE225U User Manual
JBL Speaker JRX212 User Manual
Jet Tools Planer 707400 User Manual
John Deere Lawn Mower 717 Z TRAK User Manual
Johnson Controls Automobile Parts VA 8051 User Manual
Kenwood Speaker System KFC X1720P User Manual
KitchenAid Cooktop W10240581 User Manual