TM
ZTR®
Safety Instructions & Operator’s Manual
Model Year 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Page
SAFETY & WARNING....................................4 -15
WARRANTY.........................................................16
SPECIFICATIONS..............................................17
CONTROLS..................................................18-21
OPERATION INSTRUCTIONS....................22-32
CARE & MAINTENANCE............................33-49
TROUBLESHOOTING..................................50-51
STANDARD SERVICE PARTS LIST...............52
SilverTip™
Part Number 12881-1104
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
RIDING LAWN MOWERS,
IF IMPROPERLY OPERATED
CAN CAUSE SERIOUS INJURY OR DEATH
Pictured below are the most common causes of injury to
the operator or bystander. Please read and understand
this manual to prevent injuries.
Blade Contact
Tip Over
Run Over
Back Over
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Safety Alert Symbol
When you see this symbol, BE ALERT
to the potential for injury.
Follow the recommended safety precautions and
safe operating practices.
DANGER
(highlighted in red)
indicates an imminently hazardous
situation which, if not avoided, will result
in death or serious injury.
WARNING
(highlighted in orange)
indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION
(highlighted in yellow)
indicates a potentially
hazardous situation which,
if not avoided, may result in minor
or moderate injury. It may also
be used to alert against
unsafe practices.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
GENERAL OPERATION:
Read, understand, and follow all instructions in this
manual and on the mower before starting.
Only allow responsible adults, who are familiar with the
instructions, to operate the mower.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing.
Stop mower if anyone enters the area.
Be aware of the mower discharge direction and do not
point it at anyone. Mower blades can throw rocks or other
debris.
Do not operate the mower without either the entire grass
catcher or the deflector in place. This will decrease the
possibility of injury from objects being thrown by the
mower blades.
Never carry passengers. They may fall off and become
seriously injured or interfere with safe operation of the
mower.
Mowing in reverse is not recommended because it is
difficult to maintain a clear vision of the mowing path.
However, should it become necessary to back up,
remember to look down and behind before and while
backing.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
GENERAL OPERATION (continued):
Never leave a running mower unattended. Always turn off
blades, set parking brake, stop engine and remove key
before dismounting.
Turn off blades when not mowing. Injury could occur from
contact with moving parts.
Under no circumstances should you place hands or feet
under the mower deck or in the chute while blades or
impeller are still running.
To avoid personal injury from accidental clutch engage-
ment, stop engine before removing grass catcher or
unclogging chute.
Mow only in daylight or good artificial light.
Do not operate the mower while under the influence of
alcohol or drugs.
Slow down before turning to reduce the risk of tip-over.
Watch for traffic when operating near or crossing road-
ways.
Use extra care when loading or unloading the mower into
a trailer or truck. Push, do not ride the mower when
loading and unloading.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
GENERAL OPERATION (continued):
Protect your eyes.Always wear safety goggles or safety
glasses with side shields when operating mower.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-
related injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
To protect against possible tip-over, follow the
manufacturer’s recommendation for wheel weights and
counterweights and ROPS.
Maintain or replace safety & instruction labels as
needed.
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
SLOPE OPERATION:
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result in
severe injury or death.
All slopes require extra caution. If you feel uneasy
on a slope, do not mow it!
DO
Mow across the slope with your Dixon® ZTR® --
never up or down. This will decrease the risk of
tip-over.
Remove obstacles such as rocks, tree limbs, wires
and other foreign objects that can be thrown by
mower blades.
Watch for holes, ruts, roots and bumps. Uneven
terrain could overturn the mower. Tall grass can
hide such obstacles.
Use slow speed. Tires may lose traction on slopes
even though the brakes are functioning properly.
Avoid starting or stopping on a slope. If tires lose
traction, disengage the blades and proceed slowly
down the slope.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
SLOPE OPERATION (continued):
DO (continued):
Keep all movement on the slopes slow and
gradual. Do not make sudden changes in speed
or direction.
Use extreme caution when operating the mower
with attachments to prevent tip-over or roll-over.
If front wheels lift off the ground, pull levers back to
stabilize the mower. Discontinue mowing the
slope!
Properly install and use a Rollover Protection
System (ROPS).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
SLOPE OPERATION (continued):
DO NOT
Do not turn on slopes unless necessary, and then,
turn slowly and gradually downhill, if possible. Rapid
uphill turns may cause tip-over.
Do not mow near drop-offs, ditches, or embank-
ments. The mower could suddenly turn over if a
wheel is over the edge of a cliff or ditch or if an
edge caves in.
Do not mow on wet grass. Reduced traction could
cause sliding.
Do not try to stabilize the mower by putting your foot
on the ground.
Do not use grass catcher or other attachments on
steep slopes. The added weight may change the
stability of the mower thus creating the potential for
tip-over.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
FIRE HAZARDS:
Use extra care when handling gasoline and other
fuels. They are flammable and vapors are explosive.
Store all fuel in approved containers specifically
designed for that purpose.
Allow engine to cool before refueling. Never remove
fuel cap or add fuel with engine running.
Do not smoke while refueling or operating the mower.
To reduce fire hazard, keep mower free of grass,
leaves and other debris build-up.
If gasoline is spilled, do not attempt to start the
engine. Move mower away from the area of the spill.
Do not create any source of ignition until gas vapors
have dissipated. Wipe up spilled fuel and dispose of
waste properly.
If fuel is spilled on clothing, change clothing immediately.
Before storing, allow mower to cool. Clean fuel and
oil spillage.
Never store the mower or fuel container inside a
building where there is an open flame.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
FIRE HAZARDS (continued):
To prevent fire or explosion, keep sparks and open flames
away from battery.
Keep electrical connections clean and tight. Inspect them
often. Loose connections and corrosion increase fire risk.
Before disconnecting the negative ground cable, make sure
all switches are off. This decreases the chance of sparking
and fire.
Use care when backing to avoid pushing the grass bags
into the frame or “hot” exhaust muffler of the engine. Fire
could result.
To prevent fire and explosion caused by static electricity:
Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers
on the ground away from your vehicle before filling.
When practical, remove fuel powered equipment from
the truck or trailer and refuel it on the ground. If this is
not possible, refuel such equipment on a trailer with a
portable container, rather than from a fuel dispenser
nozzle.
If a fuel dispenser nozzle must be used, keep the
nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
CHILDREN:
Tragic accidents can occur if the operator is not
alert to the presence of children.
Children are attracted to lawn mowers and the
mowing activity.
NEVER assume children will stay where they
were last seen.
Be alert to avoid accidents.
Keep children out of the mowing area and under the
watchful care of another responsible adult.
Be alert and turn mower off if a child enters the area.
Before and during backing look BEHIND and DOWN
for small children.
Never carry children. They may fall off and be seriously
injured or interfere with safe mower operation.
Never allow children to operate the mower.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to observe the following safety instructions
could result in serious injury or death.
SERVICE:
Never run a mower inside a closed area or without proper
ventilation.
Keep nuts and bolts tight, especially blade attachment
bolts, and keep equipment in good condition.
Never tamper with safety devices. Check their proper
operation regularly.
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
Never make adjustments or repairs with the engine running
unless otherwise specified.
Grass catcher components are subject to wear, damage
and deterioration which could expose moving parts or allow
objects to be thrown. Frequently check components.
Replace with original equipment parts when necessary.
(Grass catchers are not available for all Dixon® ZTR®
mowers.)
Mower blades are sharp and can cut. Wrap blades or wear
gloves, and use extra caution when servicing them.
Batteries contain sulfuric acid. To prevent burns, avoid
contact with skin, eyes and clothing.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIXON® ZTR® PRO SERIES COMMERCIAL/RESIDENTIAL WARRANTY POLICY
Kodiak™, Grizzly™ & SilverTip™ Mowers
DIXON® WARRANTS ITS ZTR® MOWERS AGAINST DEFECTS IN MATERIAL AND WORKMANSHIP
FOR THE PERIODS SET FORTH BELOW. THE SOLE REMEDY UNDER THIS WARRANTY IS
REPLACEMENT OR REPAIR OF PARTS INCLUDING LABOR COSTS.
THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMITATIONS:
1. COMMERCIAL WARRANTY (use other than, or in addition to, mowing at owner’s primary place of
residence):
a. First two years - 100% parts and labor subject to the conditions and limitations described herein
with the exception of non-covered items specified below.
b. Third year - limited to 100% parts cost as shown in the current Dixon® Parts Price List and
subject to the conditions and limitations as described herein.
c. Attachments marketed through or approved by Dixon Industries, Inc. are warranted for one year
parts and labor in commercial use applications.
d. Pro Series Models are not subject to hour meter restrictions.
e. Warranty applies to new and unused mowers and is transferable.
2. RESIDENTIAL WARRANTY (used only at owner’s primary place of residence):
a. Three years - 100% parts and labor subject to the conditions and limitations described herein for
a period of three years from date of purchase by the original owner.
b. Attachments marketed through or approved by Dixon Industries, Inc., are warranted for two
years parts and labor in residential use applications.
c. Warranty applies to new and unused mowers and is transferable.
3. Lifetime warranty on all frames and leading edge of all fabricated (welded) decks.
4. All Dixon® warranty must be accomplished by authorized Dixon® dealers and in accordance with
Dixon® warranty policy and allowances. All warranty claims must be submitted to Dixon Industries
for approval.
5. Warranty labor reimbursement to dealers based on published Dixon® flat rate schedule.
6. Warranty does not apply to damage in transit or incidents of misuse, negligence, accidents,
or alteration. The use of parts or components other than those supplied by Dixon Industries
VOIDS ALL WARRANTY.
7. Battery warranty is limited to 90 days from date of purchase.
8. The following items are not covered by this warranty policy:
(a) Routine maintenance or adjustments to include any oils, filters or other fluids used.
(b) Belts, blades and tires.
(c) Pick up and delivery charges for transportation of mower to and from an authorized
Dixon® dealer’s place of business.
(d) Engines. These are covered under a separate warranty by each individual engine
manufacturer. Consult engine manual for warranty details.
(e) Any costs or expense of providing substitute equipment while repair work is being
performed on a warranted mower.
9. THERE IS NO OTHER EXPRESS WARRANTY. TO THE EXTENT PERMITTED BY LAW, ALL
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXCLUDED; OTHERWISE, ALL SUCH IMPLIED WARRANTIES ARE
LIMITED TO THE SAME DURATION AND REMEDIES AS THE EXPRESS WARRANTY. ALL
LIABILITIES FOR CONSEQUENTIAL DAMAGES UNDER ANY EXPRESS OR IMPLIED WARRANTY
ARE EXCLUDED.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SilverTip™ ZTR® 60” & 72”
CHASSIS:
SEAT:
11GA-rectangulartube, 7GAreinforcement
Designedforoperatorcomfortwithpaddedback&arm rests. Seatis
adjustablefore&aft.Mountedonoperatorsuspensionsystem.
MOWER DECK:
2decksareavailable.Bothdecksaremadeof10GA fabricatedwelded
constructionwith1/4"reinforcement plate. 3bladescombineforeither
a 60" or 72" cut width. Deep deck with discharge tunnel. Cut height
approximately1.5"to6"via10positionlift handle.
BLADE DRIVE:
"V" Belt with Electric clutch
DRIVE SYSTEM:
EachrearwheelisindependentlydrivenbyaParkerpumpandwheel
motor.
ENGINE:
27HP Kohler or Kawasaki Twin, Liquid Cooled 4-Cycle, V-
Configuration,OverheadValve,Gasoline,Horizontal Shaft,
Aluminum Head and Crankcase with Cast Iron Liners, Full
PressureLubrication/FullFlowFilter,FixedJetCarburetor,
ElectronicIgnition, In-LineFuelFilter, HeavyDutyCanisterAir
Cleaner.
STARTING SYSTEM:
TIRES:
Electricbykeyswitchoperationwithsafetyinterlockson parkingbrake,
bladedriveclutchandcontrollevers.
Front 13-6.5x6
Rear 24-12x12
RECOMMENDED
TIRE PRESSURE:
Front 16-20lbs.
Rear 8-14lbs.
CAPACITIES:
DIMENSIONS:
Fuel-11gallons(approx)
Hydrostatoilsystem-4quartwithin-line25micronfilter
Hydrostat oil recommendation - Dixon Blue™ 15W50 Synthetic
HydrostaticFluid
Engine-2quart.SAE10W30motoroil
Width
73.5"(60"Deck),85.5"(72"Deck)
Height
Length
Weight
54"
87"
1020 lbs.(60" Deck),1054lbs.(72"Deck)
Additional information may be provided elsewhere in this manual.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
CONTROL LEVERS
Note: For access to the seat, move control levers to neutral
position and swing them outward.
TO GO FORWARD
•From neutral position, gently push control levers for-
ward.
•To increase speed, move levers further forward.
TO GO BACKWARDS
•From neutral position, gently pull control levers toward
you.
TURNING
•Turning is controlled by moving one control lever slightly
forward or rearward of the other.
•To turn left, move left lever rearward of the right lever.
•To turn right, move right lever rearward of the left lever.
•To turn on mower’s own axis (zero turning radius), stop
and move one lever to reverse position and the other to
forward position.
BRAKING
•To brake mower, move both levers in direction opposite
of travel.
LEFT TURN OPPOSITE
Note: The pressure required to operate the mower is very light.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
PARKING BRAKE:
A parking brake is located to the left of the seat.
The engine will kill if control levers are not in the outboard
position when the parking brake is engaged.
To engage brake:
pull up and back
To disengage brake:
push forward and down
Note: The parking brake is not intended to be used as
a service brake.
Note: Always set parking brake before dismounting.
Release the parking brake before moving mower.
Note: Engage parking brake before starting engine.
MOWER DECK CUT HEIGHT LIFT LEVER:
Located to the right and front of the operator.
Controls the cutting height.
Ten positions of adjustment.
Depress trigger and move lever forward to lower deck.
Depress trigger and pull lever back to raise deck.
Select cut height & insert pin into first hole below the lift lever.
Ten holes are provided for a down stop so you can easily return
from transport to desired cut height.
SEAT:
Fore & Aft: Move lever, slide seat fore & aft to desired position,
release.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
MOWER BLADE SWITCH:
To engage blades: pull up on switch
To disengage blades: push down
IGNITION SWITCH:
•Turn to start position to crank engine.
Release when it starts.
•For headlights - rotate switch one notch
counter-clockwise from run.
Note: Remove key when mower is not in use.
CHOKE CONTROL LEVER:
•Located on the control panel to the operator’s right.
THROTTLE CONTROL LEVER:
•Located on control panel to operator’s right.
•Controls engine speed.
•While mowing, throttle control should be set to MAXIMUM
or wide open setting to insure adequate cooling of the
engine and to maintain mower deck blade speed.
CIRCUIT BREAKER:
•If circuit breaker pops up, it disconnects the power. Wait 2
minutes and push to reset.
•If it pops up again, there is a short circuit. Stop and find
fault or contact your dealer.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
The safe and successful operation of the SilverTip™
ZTR™ will depend upon the operator having the correct
knowledge of all controls used on the mower and
making good judgements about the terrain to be
mowed.
NEVER allow anyone to operate the mower without
complete knowledge of all controls and their functions.
During initial operation, “learning to drive”, set throttle
at slow speed.
Sound judgement by the operator will prevent
accidents.
BEFORE OPERATING MOWER:
1.
Read engine manufacturer’s operating and
maintenance instructions.
2.
Read and observe all safety instructions on your
mower and in the manual.
3.
4.
5.
6.
7.
Check engine oil.
Check fuel cap to be sure it is in place.
Be sure parking brake is on.
Be sure mower blade drive is off.
Know how to stop engine. (Turn key to off
position).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TOWING TRAILERS AND OTHER ATTACHMENTS:
Towing a trailer or other attachment that is too heavy could damage
the drive or cause the mower to become unstable. Limit loads to 500
pounds or less with this mower.
TO FREE WHEEL MACHINE
(UNLOCK TRANSMISSION):
Always turn off engine before engaging or disengaging the
hydro release (free wheel) valves. Never attempt to move the
valves with the engine running.
The hydro release valves are located beneath the seat on the
top of the hydro pumps on each side of the machine. To unlock
the transmission, lift the seat , rotate the transmission hex valve
located on the top of each transmission approximately two full
turns counter-clockwise.
To re-engage the transmission, rotate each transmission hex
valve clockwise to the end of its travel. Return the seat to the
operating position.
Note: Before pushing or towing the tractor, the transmission
must be unlocked and the parking brake released.
The tractor should never be pulled more than two
miles per hour or for any appreciable distance.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
STARTING INSTRUCTIONS:
1. Operator must be seated in normal operating
position.
2. Set parking brake.
3. Move control levers to outboard position.
4. Assure blade clutch is off.
5. Push throttle control lever to 1/2 setting.
6. Push choke control lever forward.
*If engine is warm, turn choke off immediately after
engine starts.
*If engine is cold, slowly move choke to off as the
engine warms up.
7. Insert Ignition key and turn to start position. When
engine starts, release ignition key. Key will return to
“run” position.
8. Move throttle control lever to the wide open or
maximum setting for actual operation of the mower
deck. Engine must be operated at wide open or
maximum setting to insure adequate lubrication,
cooling and cut quality of the mower deck.
Do not operate the engine in an enclosed area
due to the harmful exhaust gas produced.
CAUTION
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING INSTRUCTIONS:
CAUTION Be sure that deflector is properly
installed on the discharge chute.
1. Start engine and set throttle at full speed.
2. Set desired cut height.
3. Release park brake.
CAUTION Check the area to assure there is
no one near.
4. Engage mower blades.
5. Move control levers in and operate per the control
instructions on Page 18.
STOPPING INSTRUCTIONS:
1. Turn mower blades off.
2. Move control levers to outboard position.
3. Set parking brake.
4. Move throttle control to slow. Allow engine to run
a short time to cool down then turn ignition key to
“OFF” and remove key.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TESTING OF SAFETY INTERLOCK SYSTEMS:
Do not operate mower if safety switches are not
operating properly.
Your Zero Turning Radius Mower is equipped with
control interlocks for your safety.
1. The engine will not start if the mower
blades are engaged.
2. The engine will not start unless the steering
control levers are neutral “OUT” position.
3. The engine will stop if the mower blade
clutch is engaged and the operator leaves
the driver’s seat.
4. The engine will stop if the park brake is ON
and the steering control levers are moved
to the “IN” position.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
INTERLOCK SWITCH TEST
Note: Operator must be seated in normal operating position
to perform these tests.
1. With engine off, turn mower blade on and attempt
to start engine.
ENGINE SHOULD NOT START.
2. With engine off, move control levers in and attempt
to start engine.
ENGINE SHOULD NOT START.
3. In a SAFEAREA, away from bystanders, start the
engine, place throttle setting at maximum or full.
Engage the blade drive through the electric clutch
switch. Raise slightly off of seat.
ENGINE SHOULD STOP!
4. With engine running, set parking brake and move
levers inboard.
ENGINE SHOULD STOP!
If any safety check fails, do not operate the mower
until the system has been checked and repaired by
an authorized Dixon® ZTR® dealer.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT:
Mulching or recycling the grass clippings requires a
totally different mowing approach than would be normal
when side discharging or bagging the grass. There
may be instances or conditions where it is not possible
to hide all the recycled or mulched clippings.
In order to achieve the best results, please read and
follow the mulching tips listed below:
1. Read and follow the installation instructions that are
included with your mulcher.
2. Set the engine speed control to the wide open or full
setting.
3. Place the mower deck cut height selector in either
the top or second notch. Never cut more than 3/4” to
1” off the grass at any one time. Attempting to cut
more grass will result in the deck plugging and cause
the engine to stall.
4. It may be necessary to cut the lawn twice to achieve
acceptable mulching performance especially on first
cuttings or if the lawn is heavily fertilized.
5. Do not attempt to cut grass when it is wet. Mulching
performance will be very poor in wet grass conditions.
6. Maintain sharp blades throughout the cutting season.
This is very important. Optimal mulching performance
cannot be obtained with a dull or nicked up blade.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT
(continued):
7. Keep the underside of the mower deck clean.
Remove all grass and dirt build-up from the under-
side of the pan, the baffles and deflectors after each
use. Never, under any circumstances, should
you place hands or feet under the mower deck
or in the chute while blades or impeller are still
turning.
8. Alternate mower direction. This will evenlydisperse
the mulched grass clippings over the lawn for even
fertilization.
If the mulching quality of the mower does not seem
to be satisfactory, try one or more of the following
tips:
a. Raise the height-of-cut setting on your
mower.
b. It may be necessary to cut your grass
more frequently.
c. Operate the mower at a slower ground
speed.
d. Overlap cutting swaths instead of cutting
a full swath with each pass.
e. Mow across the marginal areas a second
time.
f. CUT HIGH - MOW OFTEN!
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
SIDE DISCHARGE OF THE CLIPPINGS:
In order to achieve optimum performance when side
discharging the grass clippings, please read and follow
the tips listed below. Additional information can be
found in the Troubleshooting guide.
CAUTION To avoid personal injury, be sure that the
deflector is properly installed on the
discharge chute.
1. Set engine speed control to the wide open or full
setting.
2. Do not attempt to cut grass when it is wet. Wet
grass will clog the underside of the deck and
discharge area.
3. If the grass is tall, place the mower deck cut height
lever in the top or second notch. “Initially” overlap
cutting swaths instead of a full swath with each pass.
Some applications may require a second cutting.
4. Keep the underside of the mower deck clean.
Frequent removal of dried grass and dirt will allow
the clippings to discharge correctly. Never, under
any circumstances, should you place hands or
feet under the mower deck or in the chute while
blades or impeller are still turning.
5. Maintain sharp blade(s) throughout the cutting
season.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
GRASS HEIGHT & CUTTING SUGGESTIONS:
Do not attempt to cut grass when it is wet.
If the grass is tall, place the mower deck cut height
lever in the top or second notch. “Initially” overlap
cutting swaths instead of a full swath with each pass.
Some applications may require a second cutting.
Keep the underside of the mower deck clean.
Maintain sharp blades throughout the cutting season.
As a rule of thumb, never cut off more than 1/3 of the
total grass blade length. Correct mowing height can
reduce weeds and disease by 50% to 80%.
The following grass cut heights are based on adequate
moisture conditions and normal thatch build-up in a
healthy lawn. Some locations and applications may
require slightly different cut heights. If in doubt, consult
your local lawn professional for assistance.
Grass Types
Bermudagrass
Bluegrass
Buffalograss
Ryegrass
Best Cut Heights
1 - 2”
2 - 3”
11/2 -3”
2 - 3”
Tall Fescue
Zoysiagrass
3-31/2”
1 - 3”
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TO LIFT SEAT:
To lift the seat, move the control levers to the neutral
“OUT” position. Release the seat latch and rotate
the counterbalanced seat support frame upward and
forward.
To return the seat to the operating position, push the
counterbalance seat frame support rearward and
down until it rests firmly on the tractor frame.
SPRINGS:
Three seat springs are provided. The center spring
may be removed for a softer ride.
TIRES:
Correct tire pressure is essential for efficient operation
of the mower. Check tire pressure periodically. Inflate
tires to the pressure listed below.
Front tires
Rear tires
13 x 6.50 - 6 16-21 lbs.
24 x 12.0 - 12 8-14 lbs.
Lug nuts or lug bolts should be checked regularly for tightness.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
WARNING
Failure to observe the following instructions may result in personal injury.
Before performing any maintenance, turn off engine,
allow to cool & remove key.
Use extreme care when working on machinery.
Do not wear watch or jewelry.
Do not wear loose fitting clothes, and observe all
common safety practices with tools.
MAINTENANCE SCHEDULE
•Check deck drive belt tension adjustment..................after 5 hours break-in
(adjust spring tension to 7 to7-1/2 inside to inside spring hook dimension.
Check belt tension periodically. Make adjustments as necessary)
•Check deck serpentine belt....................................after 20 hours break-in
(adjust bumper to approximately 1/2” thick)
•Check crankcase oil level..................................................before each use
•Clean grass from hydrostat fans and radiator screen...........before each use
•Clean grass & debris from muffler & manifold area..............before each use
•Check air intake screen.......................................................after each use
•Clean grass under deck.......................................................after each use
•Check tire pressure..............................................................every 10 hours
•Inspect mower blades for sharpness.......................................every 10 hours
•Clean air filter element...........................................................every 25 hours
•Check hydrostatic transmission fluid......................................every 25 hours
•Grease all zerks...................................................................every 50 hours
•Check drive and fan belt.........................................................every 50 hours
•Replace air filter element.....................................annually or every 100 hours
•Check spark plugs..............................................annually or every 100 hours
•Change engine oil filter.........................................................every 100 hours
•Change engine crankcase oil.....................(5 hours break-in) every 100 hours
•Change hydrostat oil & oil filter..............(100 hours break-in) every 500 hours
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
CAUTION
Stop engine and remove ignition key for safety.
Wear heavy, thick gloves when holding onto
cutter blade, avoid the sharp edge of the blade.
MOWER BLADES:
Check sharpness of mower blades after every 10 hours
of operation. To sharpen blades, proceed as follows.
1. Remove bolt and flat washer mounting blade on
shaft. Remove blade.
2. Blades should be discarded when worn excessively.
3. Sharpen blade with a hand file, electric grinder or
blade sharpener. Wear gloves and eye protection
when sharpening. Grind blade at original 25
degree bevel.
4. Check balance of blade by positioning the blade on
a nail or blade balance pedestal. Grind the blade
on the end that is heavier until both sides balance.
5. Install blade, flat washer & bolt. Make sure to tighten
bolt to 60 ft. lbs.
Blades should be discarded when worn excessively.
DANGEROUS!
DO NOT USE
BLADE IN THIS
CONDITION!
New Blade
When notch starts,
discard blade
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
ENGINE:
For complete maintenance and operating information of
the engine, please refer to the maintenance instructions
furnished by the engine manufacturer and included in
your Zero Turn Radius mower information packet.
Note:
Air intake screen must be kept clean. If
plugged, engine may be seriously damaged
by overheating.
BATTERY:
This is a maintenance-free battery and the fluid level
cannot be checked.
OFF SEASON BATTERY STORAGE:
DO NOT remove battery from mower.
Clean top of battery and terminals with baking soda and
water.
Identify each cable so they can be reconnected to the
correct terminal.
Disconnect cables from terminals. ALWAYS disconnect
ground cable first and reconnect last.
Charge battery.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
LUBRICATION:
ENGINE:
Follow engine manufacturer’s
recommendation.
DECK SPINDLES: Lubricate with 3 “shots” only, every
100 hours.
MOWER CHASSIS: Lubricate with 3 “shots” only, every 50
hours (see zerk locations below).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
BELTS:
Check belts every 50 hours. Replace any belts found to
be in poor condition.
BELT TENSION:
Mower Deck Serpentine Belt
P/N 9758 (60”) 12033 (72”)
Manual adjustment.
Refer to illustrationfor adjustment procedure.
Idler Weldment
Idler Shock Mount
“L” Rod
Hex Nut
3/4”
(60” & 72” Serpentine)
Tighten or Loosen
Hex Nut to achieve
this dimension
Engine to Mower Deck Belt
12807 (60” & 72”)
The engine to mower deck drive belts are automatically
held in proper tension by springs which push the deck
assembly forward and do not require any additional
adjustment to be made.
Note:
Belt deflection or movement should be approximately 1/4” when
measured at mid-point between pulleys. Periodically inspect both
belt and idler systems.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HOT oil may cause burns. Allow
engine to cool before draining oil.
CAUTION
CHANGING THE ENGINE OIL:
1. The “Dapco” oil drain valve is located on either side
of the engine crankcase (depending on the type of
engine installed on your ZTR®).
2. Place a suitable container under the drain valve
hose.
3. To drain, turn hex head valve stem counter-clockwise
with a 10mm wrench or socket. Open to full open
(approximately 7 turns).
4. After engine is drained, tighten hex stem.
5. Change oil filter.
6. Fill with oil (see steps on next page).
NOTE:
Refer to engine manufacturer’s recommenda-
tions for frequency of oil changes.
Hex Head Valve
Stem
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HOT oil may cause burns. Allow
CAUTION
engine to cool before draining oil.
OIL FILL:
1. Clean any spilled oil from engine and chassis.
2. Refill engine with type, and quantity of oil recom-
mended by the engine manufacturer in engine
literature.
NOTE: Engine oil changes on the SilverTip™ will
require replacement of the oil filter. These
filters may be available from your local
Dixon® Dealer.
OIL FILTERS:
1. Replace filter each time the oil is changed.
2. Oil Filters can be obtained from your authorized
engine dealer.
3. The use of any other oil ftiler may cause damage to
the engine.
PLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS.
PROTECT YOUR ENVIRONMENT.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HYDROSTATIC TRANSMISSION FLUID &
FILTER SERVICE:
Dirt or water in fluid can ruin the hydrostatic transmissions.
SERVICE INTERVALS:
1. Initial filter service - 100 hours
2. Every 500 hours or once a year thereafter.
RECOMMENDED FLUID:
All temperatures -
Dixon Blue™ 15W-50 Synthetic Hydrostatic Fluid
~or if not available~
Normal Operating Temperatures - 20W50 ENGINE OIL
Cold climate usage - 10W40 ENGINE OIL
Use engine oil with an API classification of SG/CD.
Dixon Blue™ 15W-50 Synthetic Hydrostatic Fluid is
specifically formulated to provide excellent all-climate
performance and extended time between oil changes.
FLUID FILTER: P/N 18045 - IMPORTANT
The fluid filter is a special design for use on
“vacuum or suction” oil flow systems.
DO NOT:
Use automotive engine oil filters. These
filters require a “pressure” to allow oil flow.
Usage will result in an “air-lock” condition
with possible damage.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HYDROSTAT FLUID MAINTENANCE
PROCEDURE:
Check the fluid level in hydrostatic transmisison fluid
reservoir after every 25 hours of usage. Clean the fluid
reservoir cap and the area around it prior to removal.
Check the fluid level. Fluid should be approximately
1/4” below top of fluid tank baffle. Replenish as needed
with Dixon Blue™ 15W-50 Synthetic Hydrostatic
Fluid. DO NOT OVERFILL. When checking the fluid
level, be very careful to keep the reservoir clean.
Change the fluid in the reservoir and hydrostatic
transmission fluid filter after the first 100 hours of use,
then every 500 hours after that. Remove the filter and
be sure all fluid has drained from the reservoir. Replace
with a new OEM filter (P/N 18045) and Dixon Blue™
15W-50 Synthetic Hydrostatic Fluid.
CAUTION: Dixon Blue™ is only compatible with
standard 20W-50 motor oil or similar synthetic
motor oils.
DO NOT USE OR ADD STANDARD (RED) HYDRAULIC/
TRANSMISSION OILIN YOUR DIXON HYDROSTATIC
DRIVE. DAMAGE TO THE DRIVE COMPONENTS MAY
OCCUR. USE ONLY APPROVED DIXON BLUE™
15W-50 SYNTHETIC HYDROSTATIC FLUID OR 20W-50
TYPE ENGINE OIL.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HYDROSTATIC PUMPS:
Before each use, check to be sure that the cooling fins
of the hydrostatic pumps are clean. Excessive accu-
mulation of oil, dirt, or trash may cause the pumps to
overheat. NEVER WASH ACROSS TOP OF RESER-
VOIR WITH WATER OR STEAM. Fill reservoir as
required per the maintenance schedule listed in this
book.
HYDROSTAT DRIVE BELT REPLACEMENT
PROCEDURE:
To remove hydrostat pump drive belt:
(The hydrostat pump drive is equipped with a spring
loaded belt take-up).
1. Raise seat.
2. Remove hold down bolts from belt cover. Remove
belt cover.
3. Rotate the spring loaded take-up idler towards the
left hand hydro pump to provide belt slack for re-
moval.
4. Remove belt.
To install hydrostat pump drive belt:
1. Rotate the spring loaded take-up idler
towards the left hand hydro pump.
2. Install belt per diagram.
3. Re-attach belt cover.
4. Return the seat to the
operating position.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
PARKING BRAKE ADJUSTMENT
1. Raise rear of machine.
2. Remove tire and wheel assembly.
3. Adjust the 3/8” adjustment nut clockwise to
increase and counter-clockwise to decrease
brake holding power. As the brake holding
power is increased, the force required on the
handle to engage the brake increases.
4. Set the brake for the holding power required
for the intended use and the desired force
required to activate it.
5. Install wheel & tire assembly.
6. Repeat steps 2-5 for opposite side.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HEADLIGHT ADJUSTMENT
1. Loosen the 1/2” retaining nut underneath the
headlight and slide the headlight forward out of
the recessed area of the fuel tank.
2. Loosen the 1/2” nut on the “U” shaped holding
bracket and swivel the headlight vertically to
adjust the height of the beam. Tighten the bracket
nut.
3. Replace headlight into recessed area of the fuel
tank.
4. Swivel the headlight horizontally to illuminate the
desired area and tighten the headlight retaining
nut.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
STEERING CONTROL ADJUSTMENTS:
To adjust neutral:
1. Lift seat.
2. Block up the unit so that the drive wheels are off the
ground.
3. Loosen ball joint jam nuts on control rod.
Note: The front jam nuts are left hand threads.
4. With steering control arms in the “out” neutral position,
start the engine and run at fast idle.
5. Adjust the neutral position by turning the control rod until
the wheels do not rotate.
6. Re-tighten the jam nuts on the control rod and check to
see that the drive wheels are not turning.
7. Repeat steps 3-6 for the other side.
8. Shut off engine before removing the blocks.
9. Return the seat to the operating position.
To adjust neutral springs:
1. Loosen set screws of front and rear spring stop
collars located on the control rods. (Requires a 1/8”
Allen wrench).
2. Move control handle full forward.
3. Move front spring stop collar rearward until it com-
presses spring approximately 1/16” and tighten collar
set screw.
4. Move control handle full rearward.
5. Move rear spring stop collar forward until it compresses
spring approximately 1/16” and tighten collar set screw.
6. Repeat steps 1-5 for opposite side.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
STEERING CONTROL ADJUSTMENTS
(continued):
To adjust steering control levers:
1. Loosen the front and rear bolts retaining the bel-
lows hold down plate and slide the bellows and
plate up the steering lever to expose the steering
control mechanism.
2. Move the levers inboard to the operating position.
3. Loosen the set screw of the clamp collars which
lock the upper arms to the lower arms.
4. Raise or lower the arms for desired height. There
is approximately 3” of height adjustment available.
Upper shaft should have a minimum of 1-1/2”
engagement in lower shaft.
5. Rotate arms until they have the
desired orientation front to
back.
6. Tighten the clamp collar set
screws.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
STEERING CONTROL ADJUSTMENTS
(continued):
To adjust “In” position of the steering controls
1. Move the levers inboard to the operating position.
2. Adjust the steering lever stops until the steering levers
have the desired clearance.
To adjust for straight forward tracking.
1. Drive tractor with both control levers in the full forward
position.
2. Stop the machine and shut off the engine.
3. Adjust the forward stop of the control levers on the
side which appears to be faster to limit the forward
travel of the control levers until the mower tracks in a
straight line.
Note: Variations in the turf and tire pressure can
cause variations in speed and tracking.
When all alignment adjustments are satisfactory, slide
the hold down plate and bellows down the control levers
and secure with screws.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
LEVELING THE DECK:
1. Set the tire pressure on all four tires.
2. Front casters must be rotated in the direction of
forward travel.
3. Move the tractor to a hard level surface.
4. Put the mower deck in the number 3 deck height
position.
5. Rotate the 2 outer spindles so the blades point
outboard.
6. Adjust front hangers to level deck side to side.
7. Rotate all 3 spindles until the blades are fore and aft.
8. Adjust rear hangers until deck is level to 1/4” higher
in the rear.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
ELECTRICAL SYSTEMS:
Keep all connections clean and tight.
CLEANING THE MOWER:
Wash mower periodically. Clean above and below
deck.
High pressure washing and alkaline based soaps can
cause damage to bearings and other parts of the
mower. After washing your mower, start the engine and
engage the mower deck for a few minutes to disperse
any water that may have accumulated in bearings,
pulleys or fans.
Note:
Allow mower to cool before washing. If
bearings are hot, they will draw moisture
inside as they dry and cause corrosion.
SERIAL NUMBERS:
The serial number is located on the rear left of the frame
at rear of engine.
WARRANTY:
Refer to warranty information (page 16).
PARTS/SERVICE:
See your Dixon® dealer for replacement parts, warranty
or service.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
1. ENGINE WON’T TURN OVER
Mower blades engaged- - - - - - - - - - - - - - - - - - - - - - - - - - - -disengage blades
Drive not in neutral - - - - - - - - - - - - - - - - - move control levers to neutral “OUT”
Circuit breaker trips- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -reset breaker
Dead battery- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -charge or replace
Solenoid- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
Ignition switch- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Starter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
Parking brake not on- - - - - - - - - - - - - - - - - - - - - - - - - - -engage parking brake
2. ENGINE WILL TURN OVER BUT WON’T START
No fuel - - - - - - - - - - - refuel and/or clean or replace fuel filters/open fuel valve
Over or under choked- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - adjust choke
Spark plug not firing- - - - - - - - - - - - - check spark plug/contition or reset gap*
Carburetor maladjusted- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Ignition Switch- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
3. HARD TO START ENGINE
Fuel line clogged- - - - - - - - - - - clean fuel line/check fuel filter/open fuel valve
Faulty fuel pump- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
Spark plug wire loose or grounded- - - - - - - - - - - - - - - -check spark plug wires
Spark plugs faulty or improperly gapped- - -check spark plug/condition or reset gap*
Electronic ignition defective- - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
Dirty or maladjusted carburetor- - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
4. ENGINE STARTS BUT CUTS OUT
Water in fuel- - - - - - - - - - - - - - - - - - - - - - drain old fuel-replace with new fuel
Clogged fuel line- - - - - - - - - - - - - - - - - - - - - - - check fuel filter/clean fuel line
Fuel tank vent plugged- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -check vent
Faulty fuel pump- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Maladjusted carburetor- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
Engine dies when control levers moved “IN”- - - - - - - - - release parking brake
5. ENGINE KNOCKS
Low oil level- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -check and add oil
Ignition timing off- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
Fuel octane too low- - - - - - drain & replace with higher octane fuel
Over heated engine- - - - - - - - - - - - - - - - -shut off engine/allow to cool
*See engine manual for engine adjustments
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
6. ENGINE OVERHEATED
Radiator coolant level- - - - - - - - - - - - - - - - - - - - - - - - - - - -add coolant mixture
Air intake screen or fins clogged- - - - - - - - - - - - -clean intake screen and fins
Fuel mixture too lean- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Improper ignition timing- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Oil level too low or too high- - - - - - - - - - - - - - - - - - - - - - - - - - -adjust oil levell
Running engine too slow- - - - - - - - - - - - - - - - - - - - - - - - - - - -run engine faster
(NOTE: Always mow at full throttle setting)
7. ENGINE SOMETIMES SKIPS AT HIGHER SPEEDS
Incorrect ignition timing- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Carburetor maladjusted- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Faulty spark plug- - - - - - - - - - - -check spark plug or condition and reset gap*
8. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD
Drive belt broken or slipping- - - - - - - - - - - - - - - - - - - - - - - - replace drive belt
Pump arm loose or disconnected- - - - - - - - - - - - - - - - - - tighten or reconnect
Hydraulic oil system low- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -add oil
By-pass valves in free wheel position- - - - - - - - - - - - - - tighten by-pass valves
Hydrostat oil filter plugged- - - - - - - - - - - - - - - - - - - - - - - - - - - - - replace filter
Faulty pump or wheel motor - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
9. ENGINE STALLS WHEN BLADES ARE ENGAGED
Operator not on seat- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - sit on seat
Faulty interlock system- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Blade spindle bearing failed - - - - - - - - - - - - - - - - - - - - - - - - - - -consult dealer
Deck drive belt improperly routed- - - - - - - - - - - - - - - - - - - - - - - - - - - - reroute
Blades blocked by foreign material- - - - - - - - - - - - - - - - - - - clean under deck
10. ENGINE BACKFIRES
Carburetor maladjustment- - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
11. ENGINE IDLES POORLY
Carburetor maladjustment- - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Improper spark plug gap- - - - - - - - - - - - - - - - - - - - - - - check and re-gap plug*
51
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD SERVICE PARTS LIST
SilverTip™ ZTR®
Blades (60”)
Standard Lift
Hi-Lift
Standard Lift Fusion
Hi-Lift Fusion
Super Hi-Lift Fusion
Gator Mag Fusion
P/N 13957
P/N 13956
P/N 13958
P/N 13922
P/N 13870
P/N 13960
Blades (72”)
Standard Lift
Hi-Lift
Standard Lift Fusion
Hi-Lift Fusion
Super Hi-Lift Fusion
Gator Fusion
P/N 13962
P/N 13961
P/N 13963
P/N 13923
P/N 13871
P/N 12509
Engine to Mower Deck Belt
Serpentine Belt (60”)
Serpentine Belt (72”)
Engine to Hydro Belt
P/N 12807
P/N 9758
P/N 12033
P/N 12012
Hydrostatic Transmission Filter
P/N 18045
Air and Oil Filter
Refer to engine manufacturer’s manual for recommenda-
tions regarding frequency of service required for engine oil
changes and air filter maintenance.
Protect your engine investment, use only original equip-
ment filters. Ask your Dixon® Dealer for assistance.
IMPORTANT:
Some applications, extreme dirt conditions, or the use of
a grass catcher may require that the engine used on the
SilverTip™ ZTR® be fitted with an optional fresh air filter
system. Check with your engine service center for
availability.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
53
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
54
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S INFORMATION
Date of Purchase
Mower Model Number
Mower Serial Number
Purchased From
Name
Address
DATE OIL CHANGED
DATE ENGINE TUNED
Dixon Industries, Inc.~P.O. Box 1569~Coffeyville, Ks~620-251-2000~Fax 620-251-4117
Download from Www.Somanuals.com. All Manuals Search And Download.
Dixon® and ZTR® are registered trademarks of
Dixon Industries, Inc.
The engine exhaust from this product contains
WARNING: chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
DIXON INDUSTRIES, INC.
P.O. Box 1569
Coffeyville, Ks 67337-0945
620-251-2000
SilverTip™
Part No. 12881-1104
Download from Www.Somanuals.com. All Manuals Search And Download.
|