Cub Cadet Lawn Mower 20HP Enforcer 44 22HP Enforcer 48 23HP Enforcer 54 User Guide

Hydrostatic Zero-Turn

Commercial Riding Mower

Professional Turf Equipment

MODEL

20HP Enforcer 44

22HP Enforcer 48

23HP Enforcer 54

OPERATOR’S AND SERVICE MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

FOREWORD

The Hydrostatic Zero-Turn Riding Mower provides superb maneuverability and mid-mount cut-

ting. The machine incorporates many safety features that should be studied by all operators

before use. The list of safety precautions should receive particular attention.

This manual presents all of the operating and maintenance instructions necessary to keep

your mower at peak efficiency. If operated and maintained properly, your mower will give

dependable service.

CAUTION:

Only thoroughly trained persons should operate and maintain this

mower. This machine can cause serious injury to anyone who mis-

uses it and does not understand its operation. For their personal

safety, all operators are required to read this entire manual before

operating the mower.

Hazard control and accident prevention are partially dependent

upon the design and configuration of the equipment. Awareness,

concern, prudence and proper training of the personnel involved in

the operation, transport, maintenance and storage of the equip-

ment, are essential for hazard control and accident prevention.

NOTE: The engine manufacturer is responsible for all engine-related issues with

regards to performance, power-rating, specifications, warranty and service.

Please refer to the engine manufacturer’s owner’s/operator’s manual,

packed separately with your unit, for more information.

MODELS LISTED IN THIS MANUAL

20HP 44”,

22HP 48”,

23HP 54”,

53AH3AGF050

53AH3AGN050

53AH3AGT050

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

•

The engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals

known to the State of California to cause cancer, birth defects or other reproductive harm.

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved

forest-covered, brush-covered, or grass-covered land unless the engine’s exhaust system is equipped with a

spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be main-

tained in effective working order by the operator.

•

In the State of California, the above is required by law (Section 4442 of the California Public Resources

Code). Other States may have similar laws. Federal laws apply to federal lands. A spark arrester muffler

may be available.

IMPORTANT

SAFE OPERATION PRACTICES

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED,

COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTH-

ERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO

OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN

PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL-

HEED ITS WARNING.

Your lawn mower was built to be operated according to the rules for safe operation

in this manual. As with any type of power equipment, carelessness or error on the

part of the operator can result in injury. This lawn mower is capable of amputating

hands and feet or throwing objects. Failure to observe the following safety instruc-

tions could result in serious injury or death.

DANGER

5. Be sure the area is clear of other people

GENERAL SAFETY

OPERATIONS

before mowing. Stop machine if anyone

enters the area.

6. Never carry passengers.

7. Disengage the blades before shifting into

reverse and backing up. Always look down

and behind before and while backing.

8. Be aware of the mower and attachment dis-

charge direction and do not point it at anyone.

Do not operate the mower without either the

entire grass catcher or the chute guard in

place.

A. GENERAL OPERATION

1. Read, understand and follow all instructions in

the manual and on the machine before start-

ing. Keep this manual in a safe place for

future and regular reference and for ordering

replacement parts.

2. Only allow responsible individuals familiar with

the instructions to operate the machine. Know

the controls and how to stop the machine

quickly.

9. Slow down before turning. Operate the

machine smoothly. Avoid erratic operation

and excessive speed.

3. Do not put hands or feet under the cutting

deck or near rotating parts.

10. Never leave a running machine unattended.

Always turn off the blades, place the transmis-

sion in neutral, set the parking brake, stop the

engine and remove key before dismounting.

11. Turn off blades when not mowing.

12. Stop the engine and wait until the blades

come to a complete stop before (a) removing

the grass catcher or unclogging chute, or (b)

making any repairs, adjusting or removing any

grass or debris.

13. Mow only in daylight or good artificial light.

14. Do not operate the machine while under the

influence of alcohol or drugs.

15. Watch for traffic when operating near or cross-

ing roadways.

4. Clear the area of objects such as rocks, toys,

wire, etc. which could be picked up and thrown

by the blades. A small object may have been

overlooked and could be accidentally thrown

by the mower in any direction and cause injury

to you or a bystander. To help avoid a thrown

objects injury, keep children, animals,

bystanders and helpers at least 75 feet from

the mower while it is in operation. Always

wear safety glasses with side shields or safety

goggles during operation or while performing

and adjustment or repair, to protect eyes from

foreign objects. Stop the blades when cross-

ing gravel drives, walks or roads.

16. Use extra care when loading or unloading the

machine into a trailer or truck. This unit

Download from Www.Somanuals.com. All Manuals Search And Download.

should not be driven up or down a ramp onto

a trailer or truck under power, because the

unit could tip over causing serious personal

injury. The unit must be pushed manually on

a ramp to load or unload properly.

• Watch for holes, ruts or bumps. Uneven terrain

could overturn the machine. Tall grass can hide

obstacles.

• Use slow speed. Choose a low enough speed

so that you will not have to stop while on the

slope.

• Follow the manufacture’s recommendations for

counterweights with attachments to improve sta-

bility.

• Use extra care with grass catchers (material

collection systems) or other attachments. These

can change the stability of the machine.

• Keep all movement on the slopes slow and

gradual. Do not make sudden changes in speed

or direction. Rapid acceleration or deceleration

could cause the front of the machine to lift and

rapidly flip over backwards, which could cause

serious injury.

17. Never make a cutting height adjustment while

the engine is running if the operator must dis-

mount to do so.

18. Wear sturdy, rough-soled work shoes and

closefitting slacks and shirts. Do not wear

loose fitting clothes or jewelry. They can be

caught in moving parts. Never operate a unit

in bare feet, sandals or sneakers.

19. Check overhead clearance carefully before

driving under power lines, wires, bridges or

low hanging tree branches, before entering or

leaving buildings, or in any other situation

where the operator may be struck or pulled

from the unit, which could result in serious

injury.

20. Disengage all attachment clutches, set the

parking brake to the on position and put the

lap bars to the neutral or out position, before

attempting to start the engine.

• Avoid starting or stopping on a slope. If the

tires lose traction, disengage the blades and pro-

ceed slowly straight down the slope.

DO NOT:

• Do not turn on slopes unless necessary; then,

turn slowly and use extra care.

• Do not mow near drop-offs, ditches or embank-

ments. The mower could suddenly turn over if a

wheel is over the edge of a cliff or ditch, or if an

edge caves in.

21. Your mower is designed to cut normal resi-

dential grass of a height no more than 10”.

Do not attempt to mow through unusually tall,

dry grass (e.g. pasture) or piles of dry leaves.

Debris may build up on the mower deck or

contact the engine exhaust presenting a

potential fire hazard.

• Do not mow on wet grass. Reduced traction

could cause sliding.

22. Use only accessories approved for this

machine by Cub Cadet. Read, understand

and follow all instructions provided with the

approved accessory.

23. Do not operate or store the machine or fuel

container inside where there is an open

flame, spark or pilot light such as a water

heater, furnace, clothes dryer, etc.

• Do not try to stabilize the machine by putting

your foot on the ground.

• Do not use the grass catcher on steep slopes.

C. CHILDREN

Tragic accidents can occur if the operator

is not alert to the presence of children.

Children are often attracted to the

machine and the mowing activity. Never assume

that children will remain where you last saw

them.

1. Keep children out of the mowing area and in

watchful care of an adult other than the opera-

tor.

B. SLOPE OPERATION

Slopes are a major factor related to loss of

control and tip-over accidents, which can

result in severe injury or death. All slopes

require extra caution. If you cannot back up the

slope or if you feel uneasy on it, do not mow it.

2. Be alert and turn the machine off if children

enter the area.

For your safety, use the slope gauge included as

a part of this manual (see pg. 27) to measure

slopes before operating this unit on a sloped or

hilly area. If the slope is greater than 15 degrees

as shown on the slope gauge, do not operate this

unit on that area or serious injury could result.

DO:

3. Before and when backing up, look behind and

down for small children.

4. Never carry children, even with the blades off.

They may fall off and be seriously injured or

may interfere with safe machine operation.

5. Never allow children under 14 years old to

operate the machine. Children 14 years and

over should only operate the machine under

close parental supervision and proper instruc-

tion.

• Mow across slopes, not up and down.

• Remove obstacles such as rocks, limbs, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Use extra care when approaching blind cor-

ners, shrubs, trees or other objects that may

obscure your vision of a child or other hazard.

7. Remove the key when the machine is left

unattended to prevent unauthorized opera-

tion.

expose moving parts or allow objects to be

thrown. For your safety protection, frequently

check the components and replace with man-

ufacturers recommended parts when neces-

sary.

10. Mower blades are sharp and can cut. Wrap

the blades or wear gloves, and use extra cau-

tion when servicing blades.

11. Check park brake operation frequently. Adjust

and service as required.

12. Muffler, engine and belt guards become hot

during operation and can cause a burn. Allow

to cool down before touching.

13. Do not change the engine governor settings

or overspeed the engine. Excessive engine

speeds are dangerous.

D. SERVICE

1. Use extreme care in handling gasoline and

other fuels. They are extremely flam-

mable and the vapors are explosive.

Use only an approved container.

Never remove fuel cap or add fuel with

the engine running. Allow the engine

to cool at least two minutes before

refueling.

14. Observe proper disposal laws and regula-

tions. Improper disposal of fluids and materi-

als can harm the environment and the

ecology.

Replace the fuel cap securely (it will

“click” when correct) and wipe off any

spilled fuel before starting the engine

as it may cause a fire or explosion.

Extinguish all cigarettes, cigars, pipes

and other sources of ignition.

Never refuel the machine indoors

because fuel vapors will accumulate in

the area.

Prior to disposal, contact your local

Environmental Protection Agency to

determine the proper method for dis-

posing of the waste. Recycling cen-

ters are established to properly

dispose of materials in an environmen-

tally safe fashion.

Never store the fuel container or

machine inside where there is an open

flame or spark, such as a gas hot

water heater, space heater or furnace.

Use proper containers when draining

fluids. Do not use food or beverage

containers that may mislead someone

into drinking from them. Properly dis-

pose of the containers immediately fol-

lowing the draining of fluids.

DO NOT pour oil or other fluids into the

ground, down drain or into a stream,

pond, lake or other body of water.

Observe Environmental Protection

Agency regulations when disposing of

oil, fuel, coolant, brake fluid, filters,

batteries, tires and other harmful

waste.

2. Never run a machine inside a closed area.

3. To reduce fire hazard, keep the machine free

of grass, leaves or other debris build-up.

Clean up oil or fuel spillage. Allow the

machine to cool at least 5 minutes before stor-

ing.

4. Before cleaning, repairing or inspecting, make

certain the blade and all moving parts have

stopped. Disconnect the spark plug wire, and

keep the wire away from the spark plug to pre-

vent accidental starting.

5. Check the blade and engine mounting bolts at

frequent intervals for proper tightness. Also

visually inspect blades for damage (e.g.,

excessive wear, bent, cracked). Replace with

blades which meet original equipment specifi-

cations.

6. Keep all nuts, bolts and screws tight to be

sure the equipment is in safe working condi-

tion.

15. We do not recommend the use of high pres-

sure washers to clean your unit. They may

cause damage to electrical components; spin-

dles; pulleys; bearings; or the engine.

E. Related to Batteries

Batteries are stored electrical energy devices that

may be serviceable with removable caps (the electro-

lyte levels can be checked), or may be non-service-

able (no attempt should be made to open the vents).

7. Never tamper with safety devices. Check

their proper operation regularly. Use all

guards as instructed in this manual.

8. After striking a foreign object, stop the engine,

remove the wire from the spark plug and thor-

oughly inspect the mower for any damage.

Repair the damage before restarting and

operating the machine.

Batteries may contain lead (Pb) and sulfuric acid,

and they must be re-cycled and not disposed of nor

abandoned. Sulfuric acid can cause severe burns,

and in the event of contact, the areas should be

flushed with water and a physician contacted. Battery

cases should not be punctured. Lead is poisonous

9. Grass catcher components are subject to

wear, damage and deterioration, which could

Download from Www.Somanuals.com. All Manuals Search And Download.

attach towed equipment except at the hitch

point.

2. Follow the manufacturers recommendation for

weight limits for towed equipment and towing

on slopes.

and is contained within the positive and negative ter-

minals as well as within the battery’s internal grid-

work of plates and active materials.

A. Explosive gases are generated when batteries

are re-charged, so sparks, flames and heat sources

should be avoided. Loose connections at the battery

terminals can produce sparks and heat...connections

to the terminals must be kept tight, and the terminals

and battery surfaces kept clean of acids and corro-

sion. If batteries are re-charged or “jumped” from

external sources, make sure that the connections are

made properly and in the correct sequence...connect

to the positive terminal of the good battery first, then

connect that to the positive terminal of the weak bat-

tery. The third connection should be to the negative

terminal of the good battery, followed by the negative

terminal of the weak battery. If sparks are observed

or heating of the wiring or connectors is detected,

disconnect in reverse order (I.E., the negative termi-

nal of the weak battery first). Batteries should be re-

charged at a constant voltage...generally 14.5 +/- 0.5

volts DC for a nominal 12 volt DC battery.

3. Never allow children or others in or on towed

equipment.

4. On slopes, the weight of the towed equipment

may cause loss of traction and loss of control.

Note: 5 degrees (9%) maximum slope.

5. Travel slowly and allow extra distance to stop.

H. Suspension Seat

1. This unit is equipped with a heavy-duty vinyl

fabric-covered seat incorporating adjustable

armrests, an adjustable seatback, an adjust-

able fore/aft track, a weight/ride adjustable

mechanical suspension system, and an

Operator Presence Sensor (OPS).

2. An OPS in the form of a switch, is integrated

into the seat bottom and is connected to the

machine electrical system. The weight/ride

adjustment lever is located on the right side

of the seatback and incorporates three set-

tings: light = 110 lbs, medium = 195 lbs, and

heavy = 286 lbs. Lever up is light and down is

heavy. Weight adjustment should be made

without the operator sitting in the seat. The

seatback recline adjustment is also on the

right side between the seat back and seat

bottom, and it provides up to 10 degrees.

3. The fore/aft single-locking adjustment tracks

operate on roller-bearings for smooth and

almost effortless operation. The lever for seat

track actuation is near the right front corner

of the seat bottom, and allows fore/aft adjust-

ment of 4”.

F. Related to Fuel

1. Fuel is highly flammable and its vapors can

explode if ignited. Please respect it.

2. Do not smoke or permit others to smoke

while handling fuel.

3. Always use approved containers for fuel and

fill slowly to decrease the chance of static

electricity buildup and spillage.

4. Store fuel in well ventilated and unoccupied

buildings away from sparks and flames.

5. When dispensing gasoline into approved con-

tainers, place the container on the ground

when refueling to avoid a possible static elec-

tricity ignition of fuel vapors.

6. Do not fill containers while it is inside a vehi-

cle, trunk, the bed of a pickup or floor of a

trailer.

7. Always shut off the engine and permit it to

cool before removing the fuel tank cap.

8. Always fill the fuel tank outdoors.

9. If the fuel container spout will not fit inside the

fuel tank opening, use a funnel.

4. The seat is attached to pivotal brackets,

which allow the seat assembly to pivot for-

ward onto the foot platform area.

Note: The Operator Presence Sensor must

be connected to the electrical wiring harness.

10. When filling the fuel tank, stop when the fuel

reaches one inch from the top. This space is

necessary for tank expansion. Do not overfill

11. Wipe up any spilled fuel.

G. Towing

1. Tow only with a machine that has an

approved hitch designed for towing. Do not

WARNING-YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who

read, understand and follow the warnings and instructions in this manual and on the machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY DECALS AND LABELS

Part Number: 777I22444

Part Number: 777I22757

TO REDUCE THE RISK OF INJURY,

O T

R A T

O W

N L

DISCHARGE CHUTE COVERORGRASS

C A T C H E

IS I N I T

R O P

L A C E

D A N G E R

K E E P H A N D S a n d FE E T A W A Y

Part Number: 777S32598

Part Number: 777S30145

Part Number: 777I22741

Part Number: 777S32839

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL INFO.

Controls:

Engine ignition and start switch; throttle & choke; left and right

steering levers; electric blade clutch switch; parking brake;

mower deck lift

Parking Brake:

Seat:

Mechanical linkage attached to the brake handle

Weight adjustable suspension seat with adjustable seat back

and armrest. 4" Adjustment front-to-rear

Frame:

Instrumentation:

Structural steel, all welded construction

Hour meter

Front Caster Wheels: 13 x 5.00 - 6

Drive Wheels:

Tire Pressure:

Fuel Tank:

Ground Speed:

Net Weight:

20 x 8.00-10 for 44” & 48”; 20 x 10.00-10 for 54”

8-10 psi rear, 20-25 psi front caster

Two 5 gallons with individual shut off valves

0-8 MPH forward. 0-4 MPH reverse

726 lbs 44”; 742 lbs 48”; 759 lbs 54”

ENGINE INFO.

Engine:

20HP Kohler Command 44”; 22HP Kohler Command 48”; 23HP

Kohler Command 54”

Type:

Vertical air cooled V-Twin

Air Cleaner:

Lube System:

Starter:

Paper element and foam precleaner

Pressurized with oil filter, drain valve with hose

12-volt electric

Clutch:

Electric blade brake clutch

TRACTION DRIVE INFO.

Traction Drive:

Variable-speed integrated hydraulic charged ZT-2800 pumps

and wheel motors on each drive wheel

CUTTER DECK INFO.

Cutter Deck;Drive:

Deck Lift:

44", 48”, 54” belt driven fabricated deck

Foot lever w/ lock for height adjustment

1" to 4" in 1/4” increments

Cutting Height:

No. of Blades:

3, belt-driven, power take-off from engine

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

Figure. 1

Figure. 2

parking brake

Engine throttle

Hour Meter

Ignition Switch

Electric Blade

Clutch Switch

Choke

maintain the uphill side lap bar “essen-

tially” in a fixed position.

E. General

1. When Mowing:

a. Keep adults, children, and pets away from

k. Be careful when crossing gravel paths or

roadways. Always turn off the blade clutch

switch and wait until the blades stop rotat-

ing and raise the cutting deck to the trans-

port position. Always allow other vehicles

to have the right of way.

l. If you hit a solid object while mowing, turn

off the blade clutch switch, place the steer-

ing levers in the neutral, opened-out posi-

tion, move the throttle to slow, set the

parking brake, shut off the engine, and

take the key from the ignition switch.

Inspect for damage. Repair the damage.

Make sure the blades are in good condition

and that the blade bolts are tight before

restarting the engine.

m. Never leave the mower unattended without

performing the following: turn off the blade

clutch switch, placing the steering levers in

the neutral open-out position, moving the

throttle to slow, setting the parking brake,

shutting off the engine and taking the key

from the ignition switch.

n. Never walk or stand on the discharge side

of the mower when the engine is running.

Turn off the blade clutch switch if another

person approaches while you are operat-

ing the mower.

the area to be mowed.

b. When operating this mower, in the forward

direction, do not allow the steering levers

to return to neutral on their own. Always

maintain a firm grip on the levers, operate

them smoothly and avoid any sudden

movements of the levers when starting and

stopping.

c. If the mower is equipped for side dis-

charge, never use the mower without the

discharge chute installed and placed in the

down position.

d. Always remove debris and other objects

from the area to be mowed (Note: debris

and loose grass will reduce traction).

e. Mow only in daylight or good artificial light.

f. Watch for holes, sprinkler heads, and other

hidden hazards.

g. Avoid driving too close to trees, creeks,

ditches, sand traps, and other obstacles.

h. Before backing up, check behind and

watch where you are going.

i. Always reduce speed when making a turn,

and when grass is wet.

j. Always mow across slopes, never up and

down the slope. Do not operate on steep

slopes and slow down before turning.

Avoid turning downhill if possible, start at

the bottom and work up to the top. Use

extra care and go slowly when turning

downhill. Control the speed and direction

of the zero turn machine “primarily” with

the speed/directional control (lap bar) of

the downhill side of the machine...I.E.,

o. Never attempt to operate the traction unit

without having the mowing deck attached.

p. Keep the mower and especially the engine

and hydraulic components clean and free

of grease, grass, and leaves to reduce the

chance of fire and permit proper cooling.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Safety Awareness when Mowing

a. Do not operate on steep slopes, those

above 15 degrees (27% slope).

b. Avoid turning downhill if possible, use extra

care and go slowly.

c. Avoid turning when going downhill, traction

is at a minimum going downhill.

d. Do not operate with discharge side of the

mower toward streets, buildings, play-

grounds, parking lots, other machines, ani-

mals, and other people.

e. Avoid operation or use extreme care if the

traction surface is wet, unstable, or slip-

pery.

next and each subsequent time that the

area is mowed.

F. Controls

1. Engine Ignition and Start Switch: (See Fig-

ure 1.) Located on the instrument housing

below the right side of the operator’s seat.

When the key is inserted and turned clock-

wise, 45 degrees, the ignition circuit is closed.

Turning the switch further against spring pres-

sure starts the engine. The engine will only

start if the blade clutch switch is in the “off”

position, the parking brake is engaged and

the left and right steering levers are in the

neutral, opened-out position. The key should

always be removed from the switch if the

operator leaves the mower’s seat.

f. Use extra care when grass clippings,

leaves, pine needles, or debris are present

as traction can be reduced.

2. Engine Throttle Control: (See Figure 2.)

Located on the left side of the mower next to

the operator’s seat. Moving the throttle control

from the rear to the front will increase the

engine speed from slow to fast. Stop at the

detent, or the choke will be activated.

g. Slow-down before turning and come to a

complete stop before any zero turn maneu-

ver.

h. Do not stop machine or park machine over

combustible materials such as dry grass,

leaves, debris, etc.

3. Left and Right Steering Levers: (See Figure

3.) These hinged levers open out to the side

in any position to permit the operator to be

seated or to leave the mower’s seat. The

operator, when seated, can pull the levers up

to the operating position, a comfortable fore-

arm’s length away. These levers control all of

the movements of the mower. Pushing both

levers forward causes the mower to move for-

ward. Pulling both levers back causes the

mower to move backward. Pushing one lever

ahead of the other lever causes the traction

wheel on the side where the lever is ahead to

rotate faster than the other traction wheel,

making the mower turn toward the side where

the lever is behind. When one lever is pushed

forward and the other lever pulled back the

same amount, one traction wheel will turn in

reverse and the mower will turn within its own

length.

3. To Mow Grass and Produce a Striped Pat-

tern

a. Pick a point on the opposite side of the

area to be mowed (post, tree, shrub, etc.).

b. If on a hillside, start at the bottom so that

the turns are uphill rather than downhill.

c. Align the mower so as to head directly

toward the object on the far side.

d. Slowly increase the speed of the machine

to match cutting conditions, terrain, and

operator familiarity with the controls and

keep the machine headed directly toward

the alignment object. Do not go fast as to

reduce cut quality or to be uncomfortable

in controlling the speed and direction of the

machine.

e. When approaching the other end of a strip,

slow down or stop before turning. A U-turn

is recommended unless a zero turn is

required. The speed of a U-turn that will

allow for machine controllability and mini-

mal turf defacement will be dependent on

several factors including: the speed during

turning, the radius of the turn, the tire tread

pattern, the traction coefficient of the tire to

the traction surface, the slope of the trac-

tion surface.

In order to start the engine, both steering

levers must be in the neutral position; the

parking brake must be engaged; and the

blade clutch switch must be “off”. However,

once the engine starts, the parking brake

must be released before the operator can

move the steering levers.

f. Remember, a zero turn requires that the

forward or reverse travel of the machine be

stopped prior to the initiation of the turn or

severe turf defacement can occur.

g. To prevent rutting or grooving of the turf,

change the direction that the strips are

mowed by approximately 45 degrees the

Note: The Steering Lever will return toward

neutral when released, but they should be

placed in neutral by the driver. If the Drive

Handles are not placed in neutral, the tractor

may creep.

Download from Www.Somanuals.com. All Manuals Search And Download.

Steering Levers

Figure. 4

Fuel Shutoff Valve

8. Seat Position Adjustment Lever: The Seat

Position Adjustment Lever is located beneath

the seat. The Seat Position Adjustment Lever

is used to move the seat forward and back-

ward. To place the seat in the desired position

pull the seat adjustment lever to the left then

push the seat forward or back to the desired

position. Release the lever so the seat will

lock in place.

9. Weight Adjustment Lever: The weight

adjustment lever is located on the right side of

the seatback and incorporates three settings:

upper is 110 lbs, middle is 195 lbs, and lower

is 285 lbs.

Figure. 3

Deck Lift Pedal

4. Electric Blade Clutch Switch: (See Figure

1.) Located on the right side of the mower

beside the ignition switch. This is an “on/off”

push-pull switch that controls the electric

blade clutch which supplies power to the cut-

ting blades through the PTO. The switch must

be turned off to start the engine and should

be turned off for safety any time another per-

son approaches the mower or the mowing

deck is raised to the transport position. Power

to the electric clutch will also be cut off if the

operator leaves the operator’s seat.

5. Parking Brake: (See Figure 3.) Located on

the left side of the traction unit. The handle is

an overcenter lever which applies the drum

brakes on the drive wheels when the handle is

pulled to the rear. The brake must be engaged

in order to start the engine.

6. Deck Lift Pedal: (See Figure 3.) Located on

the panel in front of the seat. Raise the mow-

ing deck to the transport position, by pushing

the upper part of the pedal. To lower the mow-

ing deck, push on the upper part of the pedal

and lower it to the desired position.

7. Fuel Shutoff Valve: (See Figure 4.) Located

on top of each fuel tank. When turned in a

clockwise direction until it stops, it will shut off

the flow of fuel to the engine. When turned in

a counterclockwise direction it will open and

allow fuel to flow to the engine. Close this

valve if you are not going to run the mower for

a period of 30 minutes or more to prevent

flooding the engine.

10. Seatback Recline Knob: The seatback

recline knob is located on the right side

between the seat back and seat bottom

Turning it clockwise adds additional recline up

to 10 degrees.

11. Hour Meter: (See Figure 1) Located on the

right side of the mower behind the ignition

switch. The hour meter displays running time.

Note:An optional meter provides engine

speed (RPM), service reminders (oil, lube),

and running time (hours).

12. Choke Lever: (See Figure 2) The Choke

knob is located on the left side control panel

next to the operator’s seat. Having the Choke

in the ON (up) position helps the engine to

start during initial start-up. During normal

operation the Choke should be in the OFF

(down) position.

Download from Www.Somanuals.com. All Manuals Search And Download.

engine, remove the key from the ignition

switch, remove connection of the spark plugs

and using the foot pedal, lower the mowing

deck into the cutting position.

G. Initial Adjustments

1. Check the fluid levels and tires:

Note:These checks should be made daily,

before starting the engine.

b. Using a ruler, pencil and paper, measure and

note the distance from the paved surface to

the bottom edge of the mowing blade at the

front and the back of the deck on each side of

the mower. (Four dimensions.)

a. Fuel: Using a good grade of unleaded, regu-

lar gasoline, fill the fuel tank (beside the

engine on the left side of the mower). When

the fuel reaches one inch from the top of the

tank, stop. DO NOT OVERFILL. Space must

be left for expansion.

b. Engine Oil: (Filled at the factory before ship-

ment.) Pull out the oil dipstick, wipe it off and

reinsert it. Pull it out again and read the oil

level. If it is below the operating range, add oil

through the fill tube using a funnel to bring it

up to the top of the operating range.

Note:The front edge of the mowing deck

should be 1/8"-1/4" (1/8” for 1-1/2” and 1/16” for

1”) below the rear edge of the deck so that the

blades are cutting grass in only the front half of

their circular path. This decreases friction and

reduces the drive power required.

c. If the dimension at the front of the mowing

deck is 1/8"-1/4" (1/8” for 1-1/2” and 1/16” for 1”)

lower than the dimension at the rear of the

deck (pitch) on each side of the mower, do

not adjust. If not, you will need to adjust the

Lift Links (See Figure 5).

Note:Gasoline Engine: For the recommended

oil weight refer to engine manual.

c. Hydraulic Oil: (Filled at the factory before

shipment.) The hydraulic oil is contained

within the integrated hydrostatic transaxles

and an expansion tank which should be

maintained with a 1/2” to 1” above the bottom

of the tank.

outer nuts

Trailing Link

jam nut

Left Side

Note: See Maintenance Schedule Section E,

page 23.

d. Tires: 8-10 psi rear, 20-25 psi front caster

rear nuts

tires

Note:New tires are overinflated in order to

Adjustable Lift Link

properly seat the bead to the rim. The normal

working pressure for the traction tires is 8-10 psi.

The front caster wheels should be inflated to 20-

25 psi.

Figure. 5

2. Check that all Nuts, Bolts and Screws are

Tight.

3. Check the tension of the deck drive belts.

a. Remove the deck cover

b. The tension of the deck drive belts are main-

tained by a spring mechanism that adjusts for

wear and stretch.

c. Examine the belts for cuts, fraying, and

excessive wear. Replace if any of these are

detected.

d. To level the deck (side to side), place the

deck in the (3” suggested) cutting position.

With a 3/4” wrench loosen the lower jam nut

of the left side of the Lift Link. To adjust the

side of the deck up or down turn the upper

jam nut clockwise (to raise) or counter clock-

wise (to lower) a few turns.

e. To change the pitch (front to rear), loosen the

lower nuts on the rear Lift Links. With a few

turns, adjust clockwise (to raise) or counter

clockwise (to lower) the upper nuts of the rear

Lift Links. Once the deck is adjusted,

retighten lower nuts.

f. Raise the mowing deck to the transport posi-

tion using the deck lift pedal.

g. Use the deck lift pedal to lower the mowing

deck to the cutting position and repeat step

“b.” above to make sure that the desired cut-

ting height and pitch and level have been

attained. If the dimensions are not correct,

repeat steps “c.” through “f.” above.

d. Replace the deck cover.

4. Adjust the Mowing Deck: The cutting height is

set in 1/4” increments in the range of 1" to 4". Do

not attempt to raise the mower deck higher than

4” because you will damage components on

your mower. You may need to adjust the mowing

deck to achieve the proper angle for mowing.

Follow the procedures below to set the appropri-

ate angle to the mowing deck.

a. Park the mower on a flat paved surface,

engage the parking brake, shut off the

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Lubricate all fittings listed in the mainte-

nance section.

1. Make sure the park brake is set to the “ON”

position, both lap bars are in the neutral/

start position, and the Power Take Off (PTO

also referred to as blade control switch) is

in the “off” (down) position.

H. Zero Turn Break-In And Operating Pro-

cedures

2. Move the choke and the engine speed con-

trol (throttle) forward to the end of the slot.

3. Insert the ignition key, turn the switch

toward the spring-loaded “Start” position,

maintain the Start position until the engine

begins to run, then release the switch (it will

return to the “Run” position).

4. Move the choke/speed control slowly by

moving it rearward. If the engine is “cold”,

the choke may need to be partially applied

for a few minutes. Be sure to move the

choke/throttle after the engine has

DANGER:

Reread the “When Mowing” Safety Precautions.

The following procedures are suggested for operators

of ride-on machines which have zero turn capabilities.

1. Orientation:

a. Read the entire Operator’s Manual.

b. Sit on the machine, adjust the seat fore-and-

aft, then adjust the speed/directional (lap bar)

controls (they can be adjusted fore-and-aft,

as well as up-and-down — 9/16" wrench

required).

“warmed up” to the detent.

g. Check safety devices:

c. Become familiar with all of the machine con-

trols, instrumentation, safety and instruction

signs, and safety devices.

d. Move (or have moved) the machine to a safe,

level area with no obstructions including

objects, pedestrians, and animals.

2. Initial Operation:

a. Use protective equipment for eyes, hands,

hearing, feet, legs, head and other areas of

the body if needed — safety eye glasses,

gloves, earplugs, boots, hats, etc.

1. With the park brake engaged, try to move

one of the lap bars (speed/directional con-

trol) from the neutral/start position, it

should not move.

2. Repeat this procedure with the opposite

side lap bars.

3. With the park brake engaged and the lap

bars in the neutral/start position, advance

the engine speed control completely for-

ward (Hi-idle), engage the PTO control

switch (pull upward), then lift off the seat —

the engine should stop running. Sit down

and the engine should run. Turn off the

PTO by pushing the control switch down.

h. To drive in the FORWARD direction:

1. Set the engine speed to 2000 to 2500 rpm

(refer to optional tachometer on right con-

trol panel). This must be increased to full

speed (3525-3675 rpm) after becoming

familiar with the machine.

WARNING:

Hearing Protection is required for all operator

exposure exceeding two (2) hours.

b. Ensure that the area is free of animals and

bystanders, especially children!

c. Survey the area where the equipment is to be

used to make sure it is free of debris, sticks,

stones, wires, bones, and other foreign

objects which could cause injury to bystand-

ers, damage to the machine, or damage to

nearby facilities.

d. Inspect the machine to make sure:

1. All guards, shields (including mower chute

deflector) are in their proper place, are

secure, and are functional.

2. That there are no spilled or leaking fuel or

oil sources, nor loose fuel or hydraulic tank

caps, hoses or fittings.

3. That there are no loose or missing hard-

ware nor any missing items.

2. Release the park brake.

3. Slowly, move both lap bars toward the front

of the machine until the machine begins to

move forward — release the lap bars and

the machine should stop. The more that the

lap bars are moved toward the front of the

machine, the faster the machine will move

in the forward direction. Release the lap

bars and the machine should stop traveling

forward. (This is a safety check, the normal

procedure is for the operator to slowly bring

the lap bars to the neutral position).

4. Do not advance the lap bars rapidly as this

could cause turf defacement, loss of trac-

tion, and/or instability.

4. That no non-approved devices are

installed.

5. To turn, advance one lap bar ahead of the

other and the machine will turn toward the

opposite from the side that was advanced

— I.E. to turn clockwise (to the Right),

move the LEFT lap bar forward more than

the right side, and to turn counter-clock-

wise (to the LEFT), move the RIGHT lap

5. That all safety signs and decals are prop-

erly installed and legible.

e. This is a one person machine, operator only!

Riders are not permitted under any circum-

stance!

f. To start the engine on the machine:

Download from Www.Somanuals.com. All Manuals Search And Download.

bar forward more than the left side. NOTE:

If one lap bar is in the neutral position and

the other is advanced, the turn side tire will

not rotate and a “pivot turn” will be exe-

cuted — turf defacement could occur (if on

grass) as well as potential damages to the

traction surface and the tire. If the lap bar

on the turn side is not brought all the way to

neutral, then the turn side tire will continue

to rotate and a “U-turn” will be executed

with a low potential for turf defacement as

well as traction surface and tire damage.

i. To drive in the REVERSE direction:

1. Make sure no bystanders, animals, or

objects are behind the machine. Look

behind the machine, and use extreme care.

2. Slowly, move both lap bars toward the rear

of the machine until the machine begins to

move rearward. Release the lap bars and

the machine should stop. The more the lap

bars are moved toward the rear of the

machine, the faster the machine will move

in the reverse direction. Release the lap

bars and the machine should stop traveling

in reverse (this is a safety check, the nor-

mal procedure is for the operator to slowly

bring the lap bars to the neutral position).

3. Do not move the lap bars rapidly as this

could cause turf defacement and/or loss of

traction.

4. To turn, move one lap bar ahead of the

other and the machine will turn toward the

same side that was moved — I.E., to turn

counter-clockwise (to the LEFT), move the

LEFT lap bar rearward more than the right

side, and to turn clockwise (to the RIGHT),

move the RIGHT lap bar rearward more

than the left side. NOTE: If one lap bar is in

the neutral position and the other is moved,

the turn side tire will not rotate and a “pivot

turn” will be executed. Turf defacement

could occur (if on grass) as well as poten-

tial damages to the traction surface and the

tire. If the lap bar on the turn side is not

brought all the way to neutral, then the turn

side tire will continue to rotate and a “U-

turn” will be executed with a low potential

for turf defacement as well as traction sur-

face and tire damage.

3. To turn counter-clockwise, slowly move the

RIGHT lap bar forward while simulta-

neously moving the LEFT lap bar rearward.

Release both lap bars and the machine

should stop turning (this is a safety check,

the normal procedure is for the operator to

slowly bring the lap bars to the neutral posi-

tion).

Note: If low traction conditions occur, follow

these procedures for “zero turns”:

To turn clockwise (front of machine moves toward RIGHT)

when traveling FORWARD:

1. Come to a stop,

2. Then slowly move both lap bars rearward (no more

than 1/2 maximum reverse speed) to initiate REVERSE

travel,

3. Then slowly move the LEFT lap bar forward while

maintaining the RIGHT lap bar in the rearward travel

position.

4. To stop the turn and reintiate FORWARD travel,

slowly move the RIGHT lap bar from the REVERSE

travel position to a FORWARD travel position equal to

that of the LEFT lap bar.

5. Alternatively, release both lap bars and the machine

should stop turning, (this is a safety check, the normal

procedure is for the operator to slowly bring the lap bars

to the Neutral psoition).

To turn counter-clockwise (front of machine moves toward

LEFT) when traveling FORWARD:

1. Come to a stop,

2. Then slowly move both lap bars rearward (no more

than 1/2 maximum reverse speed) to initiate REVERSE

travel,

3. Then slowly move the RIGHT lap bar forward while

maintaining the LEFT lap bar in the rearward travel

position.

4. To stop the turn and reintiate FORWARD travel,

slowly move the LEFT lap bar from the REVERSE travel

position to a FORWARD travel position equal to that of

the RIGHT lap bar.

5. Alternatively, release both lap bars and the machine

should stop turning, (this is a safety check, the normal

procedure is for the operator to slowly bring the lap bars

to the Neutral psoition).

3. Start the Engine:

a. Open the fuel shutoff valve.

b. Sit on the Seat. Set the parking brake “On”.

c. Move the left and right steering levers to the

neutral position.

d. Turn the electric blade clutch switch “Off”.

e. Push the choke/throttle control to the full for-

ward position.

j. To perform a “zero turn”:

1. Please note, a zero turn maneuver can not

be executed while the machine is moving in

the forward or, reverse directions, the

machine must come to a stop first.

f. Insert the key in the ignition and start switch

and turn the switch to “On”.

g. Turn the ignition key in a clockwise direction

to the “Start” position until the engine starts.

2. To turn clockwise, slowly move the LEFT

lap bar forward while simultaneously mov-

ing the RIGHT lap bar rearward. Release

both lap bars and the machine should stop

turning.

Note:Do not hold the key in the “Start” posi-

tion for more than 10 seconds or you may dam-

age the starter. If the engine does not start in this

time, wait about 30 seconds and try again.

Download from Www.Somanuals.com. All Manuals Search And Download.

h. Gasoline Engine: Once the engine starts,

move the choke/throttle to the detent as

the engine warms.

b. Use the Deck Lift pedal to raise the mow-

ing deck to the transport position.

c. Drive the mower to the cleanup or storage

area.

d. Move the throttle to slow.

e. Place the steering levers in the neutral

position.

f. Set the parking brake.

g. Turn off the ignition switch and take the key

from the switch.

4. Operating the Mower: Operating a zero-turn-

ing-radius mower is not like operating a trac-

tor-type riding mower. The zero-turning-radius

mower is much more maneuverable and

much less fatiguing to operate. However, get-

ting used to the fingertip control of the zero-

turning-radius mower takes some practice.

We strongly recommend that you locate a

“test area” where you can operate the mower

for about 30 minutes without being disturbed.

a. Get into the operator’s seat.

h. Close the fuel shutoff valves.

i. Never park near open flames or ignition

sources.

I. Mower Cutting Blades

b. Start the engine.

The blades normally “factory installed” on a mower

afford the best grass cutting performance on the

majority of grasses and mowing conditions; however,

there will be occasions whereby the grass type,

stage of grass growth, soil conditions, and weather

conditions will require different cutting blade types.

Since the mower decks are designed so that over-lap

of the cutting blades generally exceed 1.5”, there is

no need for orientation of one cutting blade to an

adjacent blade (I.E., the blades do not need to be

“timed” nor synchronized).

c. Use the deck lift pedal to raise the mowing

deck to the transport position. Make sure

the blade clutch switch is off.

d. After the engine has warmed, adjust the

throttle to the fast position.

e. Release the parking brake.

f. Fold in the steering levers to the operating

position.

WARNING:

When operating this mower forward, do not

allow the steering levers to return to the neu-

tral position on their own. Always maintain a

firm grip on the steering levers, operate them

smoothly and avoid any sudden movements of

the levers when starting or stopping.

Hi-lift- These are generally the best cutting blades

for most grasses and mowing conditions. These

blades will provide extra “lift” for the thinner leaf

grasses, will handle lush grasses, and will provide

maximum grass and debris discharge. These blades

are generally required for material collection sys-

tems. More horsepower is required for these blades

when compared to others, and they generally pro-

duce the highest noise levels.

g. To go forward, move both steering levers

slightly forward and the mower will slowly

move forward. The farther you move the

levers forward the faster the mower will go

forward.

h. To back up, move both steering levers

slightly backward and the mower will

slowly move backward. The farther you

move the levers backward the faster the

mower will go backward.

i. To turn, pull the lever back on the side to

which you want to turn. The farther back

you pull the lever, the faster and more

sharply you will turn. Initially, you will have

to be careful to avoid turning too fast and

too far.

j. After you have mastered operating the

mower, use the transport lever to lower the

mowing deck to the cutting position and

pull on the electric blade clutch switch to

start the blades rotating.

Medium-lift- These blades require less horsepower

than the hi-lift, and they generally work well in wider

leaf grasses and some mulch applications.

Low-lift- These blades require less horsepower than

hi-lift and medium-lift blades, and they generally work

best with wide leaf grasses, sparse grass growth,

and sandy soil conditions. They generally produce

the lowest noise levels. Bahia blades are configured

without offset, and with a maximum amount of sharp-

ened cutting edge.

Mulch- These blades are generally designed for use

in cutting decks equipped with mulch baffles. The

shape of the blade generally produces higher turbu-

lence in order that the grass can be repeatedly cut

and re-cut into smaller pieces. These blades gener-

ally require more horsepower than other blades.

Mulch blades work best when the grasses are cut at

the highest levels, minimal lengths of grasses are

removed, and grass conditions are generally dry.

k. Practice mowing in straight passes. When

you feel confident, slowly practice mowing

around obstacles such as trees.

5. Parking the Mower:

a. Push off the electric blade clutch switch.

Download from Www.Somanuals.com. All Manuals Search And Download.

m. Clean up the grass clippings and other

materials washed from underneath the

mower deck, and dispose of them properly.

MAINTENANCE AND

SERVICE

Hose Coupler

(Shown without

Hose Attached)

WARNING:

Disconnect the spark plug wires or remove the

key from the ignition to prevent the engine

from accidentally starting before performing

any maintenance on this mower.

Water Port

A. Cleaning your Deck

Use the Deck Wash System to rinse grass clip-

pings fro the deck’s underside and prevent the

buildup of corrosive chemicals. Complete the fol-

lowing steps after each mowing:

IMPORTANT: Make certain the machine’s dis-

charge chute is directed away from people, chil-

dren, animals, and your house, garage, parked

cars, etc.

a. Drive the machine to a level, clear spot on

your lawn, near enough to a water faucet

(spigot) for your garden hose to reach.

b. Make sure that the PTO (mower deck

blade engage) control is in the “OFF” posi-

tion.

c. Move shift lever or speed control into the

“Neutral” position.

d. Set the parking brake, and turn the ignition

key to the “STOP” position to stop the

engine.

Figure. 6

B.Mower Deck

1. Removing the Mower Deck:

a. Apply the parking brake. Remove ignition

key and both spark plug caps.

b. Lower the cutter deck to the lowest setting

and capture the lift pedal by placing the

height of cut clevis pin into the “Lock” hole.

c. Remove tension of the PTO belt by moving

the belt tensioning spring.

Note:There is a certain amount of spring

tension due to the weight of the deck. When

removing the lift linkage from the deck the ten-

sion of the springs will go from the deck to the

deck lift pedal. Not capturing the deck lift

pedal while removing the lift linkage from the

deck will cause it to snap back.

e. Thread hose coupler (packaged with this

manual) onto the end of your garden hose.

See Figure 6.

f. Attach the hose coupler to the water port

on your mower deck’s surface. See Figure

6. Turn the water on.

d. Detach the mower drive belt.

g. While sitting in the machine operator’s

position, re-start the engine and place

throttle lever in the Fast (rabbit) position.

h. Move the PTO control to the “ON” position.

i. Remain in the machine operator’s position,

and with the mower deck engaged for a

minimum of two minutes per wash out,

start with the trim (operator’s left) side, and

allow the underside of the cutting deck to

thoroughly rinse.

j. Move the PTO control to the “OFF” posi-

tion.

k. Turn the engine off.

l. Turn the water off, and detach the hose

coupler from the water port on your mower

deck.

e. Remove the four hair pins from the right

and left side of the mower. Shift the deck

forward until the Trailing Link is free and

you are able to remove the deck.

f. Turn front caster wheels outward.

g. To install reverse the process

2. Changing a Blade:

a. Remove the key from the ignition and dis-

connect the spark plugs.

b. Jack up the front of the mowing deck about

one foot and block it in that position.

c. Wrap a rag around one end of the blade

and grasp it to prevent it from turning, or

secure the blade by placing a block of

wood between the blade and the deck

housing.

d. Use a 1-1/8" socket wrench on the pulley

side of the spindle bolt.

e. Remove the hex nut at the blade using a 1-

1/8" wrench.

Download from Www.Somanuals.com. All Manuals Search And Download.

Trailing Link

hair pin

hair pins

Figure. 7

f. Remove the blade.

b. Unscrew the nuts from the deck covers

g. To replace the blade reverse the above

process and tighten nut to 100-120 lb ft.

and remove both covers.

c. Using a 1/2" socket breaker bar or socket

ratchet insert the drive end into the 1/2"

square opening in the lower idler arm

assembly and push the idler arm counter-

clockwise. While holding the idler arm

back, loosen the blade drive belt from the

pulley and slide the belt away from the pul-

ley.

d. Remove tension of the PTO belt by moving

the belt tensioning rod. Loosen the belt

retaining bolt.

e. Pull the tensioner pulley away from the belt

and remove the PTO belt then remove the

blade drive belt.

Note: Add a small amount of multi-purpose

grease to the bolt threads to avoid corrosion

and galvenic action

WARNING:

Never mow with dull blades! Blades that are

bent should be replaced! The cutting blades

are sharp and can cause severe injury. Wrap

the cutting surface of the blade with a rag to

avoid injury.

3. Sharpening the Blade:

f. Reverse the process to install the belt.

a. Set the parking brake.

b. Clean any debris from the blades. Keep

blades sharp and free of build up at all

times.

c. Sharpen blades evenly at the original 30°

angle to maintain balanced cutting blades.

Do not sharpen the underside of the

blades. Use a electric blade sharpener, a

conventional electric grinder or a hand file

to sharpen the blades.

Note:When replacing belts do not over-

tighten. Adjust the idler pulley so that a ten-

pound pull with a spring scale between two

pulleys deflects the belt about 1/2".

d. Replace any blade with severe nicks or

dents that cannot be removed by filing.

e. Check the balance of the blade after

sharpening by placing it on a blade bal-

ancer. Do not use un-balanced blades.

f. If the blade dips on one end, file stock off

of the cutting surface on that end.

Note:Blades that cannot be easily bal-

anced—REPLACE.

4. Changing the Blade Drive Belts:

a. Set the parking brake. Remove ignition key

and both spark plug caps.

Download from Www.Somanuals.com. All Manuals Search And Download.

D.Electrical Circuit

Danger:

Read General Safety Precautions Nos. 9 and 10.

1. Battery: The battery is located beneath the

operator’s seat. If so equipped, remove the

fillcaps and check the level of the liquid elec-

trolyte in the battery every 50 operating hours.

If the level in any of the six cells has dropped

below the bottom of the split ring inside the fill

hole, refill the cell with distilled water. To keep

the outside of the battery clean, brush on a

strong solution of bicarbonate of soda and

water and rinse with clean water. Keep the

contacts and cable ends clean with a wire

brush and make sure the connections are

tight. Coat the terminals with petroleum jelly

to prevent corrosion.

Spindle

Figure 8

2. Battery Removal

5. Changing the Spindle Assembly

a. Jack up the front of the mowing deck about

one foot and block it in that position.

b. Make sure the blade clutch is disengaged.

c. Remove the deck cover.

Warning:

When removing the cables from the battery

follow these steps to avoid a short between

the wrench and the frame.

d. Remove the drive belts. (See 4. Changing

Blade Drive Belts.)

e. Remove the cutter blade. (See 2. Chang-

ing a Blade.)

a. Remove the negative (black) cable.

b. Remove the positive (red) cable.

c. Release the hold down straps.

d. Remove the battery without tipping.

3. Battery Storage: When storing the mower for

long periods of time the following guidelines

should be performed.

f. Using a wrench or socket ratchet remove

four hex nuts, and the four hex head cap

screws. Remove the spindle assembly.

g. Reverse the process to install the spindle

assembly.

a. Disconnect the battery cables from the ter-

minals and remove the battery.

C.Hydrostatic Drive System

1. Your zero turn riding mower is equipped with

b. Clean the battery before storing. A dirty

battery will lose its charge over time.

c. Store the battery with a full charge. A dis-

charged battery will freeze (refer to the

table below).

dual integrated hydrostatic pumps, motors, and

gear reduction transaxles The fluid level in the

expansion tank must be maintained at 1/2” to 1”

above the bottom of the tank. See Figure 9.

Specific Gravity

1.265

Freezing Temp (°F)

expansion tank

-71

-62

-16

1.250

1.200

Hydrostatic

Transaxles

1.150

1.100

d. Recharge battery when ever the specific

gravity value is less than 1.225

4. Installing the Battery

Figure 9

Note: See Maintenance Schedule, Section E,

page 23.

Note:The battery is delivered from the fac-

tory fully charged and filled with electrolyte.

Download from Www.Somanuals.com. All Manuals Search And Download.

a. Attach the positive (red) cable.

b. Attach the negative (black) cable.

c. Attach the rubber battery strap.

5. Jump Starting

and all sparkplug wires. The air-gap should

be checked with feeler gages in the three

slots of the BBC (PTO Clutch). The air-gap

should be adjusted to 0.012" to 0.015". There

are three inspection slots in the brake cover.

To adjust, successively tighten each of the

three gap adjustment nuts an equal amount.

Insert a feeler gage (0.012" to 0.015") into

each slot as the air gap adjustment nut are

tightened. The correct adjustment occurs

when slight contact with the feeler gage

occurs. Engage the BBC (PTO Clutch) a cou-

ple of times, and re-check the air-gap. If it is

not between 0.012" and 0.015", repeat the

adjustment procedure.

Warning:

Failure to use this starting procedure can cause

sparking, and the gases in the battery to

explode.

a. Attach the end of the red jumper cable to the

positive terminal (+) of the charged battery.

b. Attach the other end of the red jumper cable

to the positive terminal (+) of the low charge

battery.

c. Attach the end of the black jumper cable to

the negative terminal of the charged battery.

d. Attach the other end of the black jumper

cable to the frame of the unit with the low

charge battery.

6. Fuses: There is one fuse located in the wiring

between the battery and ignition start switch.

This is a standard plug-in type automotive fuse

rated at 20 amp.

7. Safety Switches: There are three safety

switches in the electrical circuit which control the

engine. They are (1) the blade clutch switch, (2)

the parking brake/lap bar switch, (3) the seat

switch.They operate so that in order to start the

engine, the blade clutch switch must be off, the

parking brake must be engaged, and both steer-

ing levers must be in the neutral position. Once

the engine is started, the seat must be occupied

and the parking brake must be released before

either of the steering levers can be moved. Also,

the seat must be occupied before the blade

clutch switch can cause the blades to rotate.

8. Safety Switch Operation Checks: The follow-

ing operational checks should be made daily.

a. Blade Clutch Switch: Sit in the operator’s

seat. With both steering levers in the neutral

position and the parking brake engaged, turn

the blade clutch switch “on” and try to start

the engine. The engine should not start. If it

does, the blade clutch switch must be

b. Parking Brake Switch: Sit in the operator’s

seat. With both steering levers in the neutral

position and the blade clutch switch “off”,

release the parking brake and try to start the

engine. The engine should not start. If it

does, the parking brake switch must be repo-

sitioned or perhaps replaced. If the engine

does not start, engage the parking brake and

start the engine. Swing one steering lever up

to the operating position and the engine

should stop. If the engine does not stop, the

parking brake switch must be repositioned or

replaced.

c. Seat Switch: With both steering levers

opened-out to the neutral position, the park-

ing brake engaged and the blade clutch

switch in the “off” position, start the engine.

Now release the parking brake, hold down on

the back of the operator’s seat against spring

pressure, and swing one of the steering

levers up to the operating position. Release

the operator’s seat and the engine should

stop. If the engine does not stop, the seat

switch must be replaced. With both steering

levers folded out in the neutral position, the

parking brake engaged and the blade clutch

switch in the “off” position, sit in the opera-

tor’s seat and start the engine. Turn the blade

clutch switch to the “on” position and the

blades should start to rotate. Raise up slightly

off the operator’s seat and the blades should

stop. If the blades do not stop when you dis-

mount from the operator’s seat, the seat

switch must be replaced.

replaced. If the engine does not start, turn

the blade clutch switch “off” and start the

engine. Now turn the blade clutch switch “on”

and the blades should rotate. If the blades do

not turn, the blade clutch switch must be

replaced, the seat switch must be replaced or

the electric PTO clutch must be repaired. The

air-gap should be checked every 100 hrs. (or

less, if severe operating conditions exist such

as when there are many on/off cycles, mulch-

ing operations, material collection systems

used, and dusty/dirty conditions), and the air-

gap adjusted if more than 0.025". To inspect,

remove the “negative” cable from the battery

d. Electric PTO Clutch: This clutch operates

when the engine is running, the operator is in

the operator’s seat and the blade clutch

switch is turned on. This electric clutch is a

fairly trouble free device. If a problem devel-

ops and the blades do not turn, first check the

20 amp fuse in the yellow, 16-gauge wire

between terminal “L” on the ignition switch

and the hour meter and then investigate the

wiring harness and the connections to the

Download from Www.Somanuals.com. All Manuals Search And Download.

seat switch, the blade clutch switch and the

electric blade clutch. Then check the seat

switch, the blade clutch switch and finally the

electric blade clutch.

and repeat the inspection. If the leaks you find

are pin hole size to 1/16" diameter, the tire can

be repaired. If the leaks are larger than 1/16"

diameter, the tire can be repaired. If the tire

bead is damaged, the tire can be repaired or the

tire will have to be replaced.

E.Tires

The two front wheels are caster wheels that are free to

swivel to accommodate the direction of the mower.

3. Creeping: Creeping is the slight forward or

backward movement of the mower when the

throttle is on and the lapbars are in the opened-

out position. If your mower creeps do the follow-

ing.

The two rear wheels are used to propel the mower in the

direction of input from the drive handles. Inflation

pressure of the rear tires is important for stability while

the mower is in operation. If the tire diameter is not

equal between the two tires, the mower will pull to one

side.

a. Jack up rear of unit.

b. Place Lapbars in the neutral position.

c. If the tires are rotating, the neutral position

that side transaxle linkage will need to be

adjusted. Contact your service representa-

tive.

1. Inflation Pressure:

a. Traction Tires—20 psi max; 8-10 psi recom-

mended

F. Brakes

b. Front Caster Wheel—28 psi max; 20-25 psi

recommended

While the mower is in motion, all braking is performed

dynamically through the hydraulic pumps and traction

motors, controlled by the two steering levers. When the

mower is parked with the engine shut off, the hydraulic

system locks the traction wheels.

c. Cutting Deck Ball Wheels—Solid Polyure-

thane.

Use the Following guidelines for maintaining the tires:

a. Balance inflation pressure between the rear

tires to help maintain straight travel (see tire

side wall for proper inflation pressure).

b. Keep the valve caps tightened to prevent air

pressure loss.

Note:To move the mower forward or in

reverse by pushing, you must release the

dynamic braking. Locate the release levers at the

rear of the machine. Pull them toward the rear

and lower the wide area of the rod into the key-

hole slot. (See photo below).

2. Leaking Tires: When a flat tire occurs, repair or

replace immediately. The normal procedure is to

remove the wheel and replace it. If a tire is get-

ting soft, park the mower on the nearest level,

paved area. If the leaking tire is on a traction

wheel, put blocks on each side of the opposite

traction wheel and jack up the tire that leaks

about an inch off the ground. Loosen and

remove the lug nuts and remove the wheel.

Mount a wheel and tire, replace the lug nuts, and

using a torque wrench, tighten them to 60 10

ft-lbs.

If the leaking tire is on a front caster wheel,

block both traction wheels and raise the caster

wheel so that the tire is an inch off the ground.

Loosen and remove the locknut from the axle

assembly and pull the axle assembly from the

caster yoke. The wheel and two spacer sleeves

will drop free. Slip the axle assembly through

one side of the caster yoke, through a spacer

sleeve, a wheel, the other spacer sleeve and

finally through the other side of the caster yoke.

Then tighten the locknut on the end of the axle

assembly.

Hydro Release Valve

When the mower is parked with the engine running and

the steering levers in the neutral position, the parking

brakes should be applied. The parking brakes are

internal gear/pawl brakes mounted in each transaxle.

They are both engaged by the same operating lever.

1. Adjustments: The parking brake handle is an

over-center lever in a slot that should engage

with moderate force. The parking brakes pro-

vide a positive means to hold a machine station-

ary that is similar to “Park” on an automobile.

Lower the mower off the jack and continue

mowing. The wheel with the leaking tire should

be inflated to 20 psi and the wheel placed in a

large bucket of water. Carefully inspect the tire,

rim and valve for escaping air bubbles which

indicate a leak. Mark each leak with a yellow

marking crayon and then deflate the tire to 8 psi

Note:The parking brakes normally do not

need to be adjusted.

To adjust either brake individually, loosen the jam nuts

Download from Www.Somanuals.com. All Manuals Search And Download.

on the cable near the brake arm on the transaxle. If

the brake is not holding, adjust the nuts so that the

brake cable housing moves away from the lever.

tor. Start the engine and allow it to run out

of fuel. This will prevent gum and varnish

deposits from forming. Replace the fuel fil-

ter.

2. Repair: The mower is equipped with internal

gear/pawl brakes and will not normally require

maintenance. If they are not working properly,

please contact your service center.

g. Gasoline Engine Only: Remove the spark

plugs and pour approximately one ounce

of oil into each cylinder. Crank the engine

one or two turns to spread the oil evenly on

the cylinder walls. Replace the spark

plugs.

G. Hydraulic System

1. Hydrostatic Pumps and Motors: The pumps

in the transaxles are the hardest-working

components in the hydraulic system. They are

in operation all the time the engine is running.

Because of extremely close tolerances, wear

is an important factor in their life.

h. Clean the battery and make sure it is fully

charged.

i. Jack the mower up and store it on blocks to

take the weight off of the tires.

2. To Put the Mower Back in Service:

a. Check the battery. Charge if necessary.

b. Gasoline Engine Only: Remove the spark

plugs and wipe them off. Using the starter,

crank the engine to pump the excess oil

out of the spark plug holes. Replace the

spark plugs and the ignition leads. Refill

the fuel tank with fresh gasoline.

Note:The pumps and motors are not

owner-repairable. If a pump fails, contact your

Cub Cadet dealer. Do not disassemble the

pump/motors. For proper maintenance refer

to the Maintenance Schedule, Section E, page

23.

2. Steering Lever Adjustments: Place the

mower on level ground with the engine run-

ning, parking brake off and steering levers in

neutral position. If the mower begins to creep

contact your service representative.

c. Check the level of the oil in the crankcase

and the hydraulic tank.

d. Lower the mower off the block and check

the tire pressure.

e. Push the mower outdoors and start the

engine. Let the engine idle until it has

warmed up completely (4 to 5 minutes).

H. Storage

1. General: If your mower will not be in service

for a few months, it should be stored in a dry

location that is not subject to drastic changes

in temperature. Before storing, the following

maintenance procedures should be per-

formed.

a. Clean the mower. The entire tractor and

cutting deck should be washed and

cleaned.

b. Sharpen the blades so that the mower will

be ready to use when needed.

c. Protect the metal surfaces. Repair

scratches with the appropriate touch-up

spray paint. Brush a rust preventive oil on

any unpainted surfaces including the pul-

leys and blades. (Be careful not to get any

oil on the drive belts.)

d. Lubricate the mower.

e. Drain the engine oil. The engine should be

warm so that all the oil drains. Replace the

engine oil filter and refill the crankcase with

fresh oil.

f. Gasoline Engine: Drain all the fuel. Close

the fuel tank shutoff valve. Disconnect the

fuel line from the carburetor and put the

end into an approved fuel container. Open

the fuel tank shutoff valve and drain the

fuel tank and line into the approved con-

tainer. Replace the fuel line on the carbure-

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Lubricate all grease fittings. Follow the

MAINTENANCE SCHEDULE

Lubrication Chart.

A. Daily Checks

D. Every 100 Hour Checks

1. Change the engine oil filter. (Every 50 hours

under heavy duty operation.)

1. Before starting engine:

a. Check the fuel level by viewing in the tank.

b. Check the engine oil level.**

c. Check the hydraulic transaxels for leaks.

d. Check the tires and tire pressure.

Drive Tires: 8-10 psi.

2. Check the engine spark plugs.

3. Check the air gap on the blade brake clutch

(PTO Clutch) and if it exceeds 0.025” adjust to

0.012” - 0.015”.

Front Caster Wheels: 20-25 psi.

e. Check the spindle belt, the mower drive

belt and the hydro drive belt.

f. Check the blades. Make sure they are

sharp and that the blade securing cap

screws are tight.

E. Every 300 Hour Checks

1. Change the hydrostatic fluid in the transaxles.

2. Change the filter in the transaxles.

* Perform maintenance more frequently under dusty

conditions.

g. Check the cutting height.

2. When ready to start the engine:

a. Check the seven safety switches for proper

operation.

**Reference Engine Owner’s Manual

3. After mowing:

a. Clean the mower.

b. Clean the engine air screen.

c. lubricate the wear points. Follow the Lubri-

cation Chart.

d. After the first five hours, change the engine

oil and engine oil filter.

B. Every 25 Hour Checks

1. Service the engine foam element air cleaner.*

2. Grease the three spindle bearings.

3. Check fluid level in the transaxle expansion

tank. The level should be maintained

between 1/2” and 1” when “cold”.

C. Every 50 Hour Checks

1. Change the engine oil. (Every 25 hours under

heavy duty operation.)

2. Clean or replace the engine’s paper air

cleaner element.*

3. Check the battery’s electrolyte level, if

equipped with fill caps.

4. Clean the engine cooling fins and external

surfaces.*

5. Lubricate wear points. Follow the Oil Chart.

Download from Www.Somanuals.com. All Manuals Search And Download.

OIL CHART

Apply a few drops of SAE 15W-40 engine oil, grease, or use a spray

lubricant. Apply the oil to both sides of pivot points. Wipe off any excess.

Start engine and operate mower briefly to insure that oil spreads evenly.

Number of Oil Points

Description

DAILY

Deck Suspension Pivots

Height Adjustment Turnbuckle Clevis Pin

Height Adjustment Handle Pivots

Height Adjustment Stop Pivots

Deck Lift Linkage Pivots

Transport Handle Pivots

Transport Handle Pin

Deck Frame Up-and-Down Pivots

WEEKLY

Seat Hinge

Steering Lever Linkage Rod End Bearings

Lever Return Assembly Rod End Bearings

Pump Control Lever Pivots

Grass Collection System Lid Hinges

(If Mower is so equipped)

LUBRICATION CHART

Use a grease-gun filled with NO. 2 Multipurpose Grease

No. of Grease Fittings

Description

EVERY 25 HOURS

Blade Spindle Bearings

WEEKLY

Front Caster Wheels

Front Caster Wheel Spindles

Mowing Deck Pivots

Deck Take-Up Idler Pivots

Mower Deck Ball Wheels

Engine oil: Rimula 15W40 recommended or 10W40 engine oil rated SJ or higher.

Hydrostatic Fluid: Rimula 15W40 recommended. To fill the expansion tank to proper level, about 1”

above the tank bottom where “cold”. If the filter and fluid are removed, a new filter should be used and the tran-

saxle filled via the expansion tank with Rimula 15W40.

Spindle Lubricant: Use only Shell Alvania RL 2 grease. This grease is an amber-colored grease

designed for high speed bearing applications. It has a base oil viscosity that reduces running losses, has been

formulated for low noise, has excellent corrosion protection, and has excellent bearing lubrication.

General Purpose Lubricant: Use any NLGI grade 2 multi-purpose grease. Shell Albida EP2 is recom-

mended. Shell Albida EP 2 is a red-colored multi-purpose grease designed for heavy-duty bearing applica-

tions. It has high base oil viscosity for mechanical stability, has been formulated for high load, low-speed

applications, and has excellent lubrication and corrosion protection.

Download from Www.Somanuals.com. All Manuals Search And Download.

B. Engine RPM Check and Adjustment

Performance Adjustments

Table 1

Description

High RPM Spec. Low RPM Spec.

3400 +/-75 1550 +/-100

A. High Speed Tracking Adjustment

20, 22, 23 Kohler

If mower tracks to one side with both lap bars in fully

forward position:

NOTE: RPM Specs. are for free running engines under no load.

1. Verify that the lap bars are in the neutral posi-

tion, the parking brake is on, and the PTO

drive is disengaged.

2. Start the mower and let it run at approximately

half throttle for 3-5 minutes to bring the engine

up to operating temperature.

3. Locate the (optional) Hour Meter/Tachometer/

Service Minder display on the right hand

operator control panel if so equipped, or use a

hand-held tachometer. (see Fig.1 on page 10

of the manual) This display defaults to the

tachometer mode when engine is running.

4. Move the throttle lever to the high speed posi-

tion and note the RPM reading on the display.

5. Move the throttle lever back to the low speed

position and again note the displayed RPM’s.

6. Compare these noted RPM readings to the

specifications in Table 1, for the engine that is

on your mower.

1. Check air pressure in all four tires:

a. Pressure should be within specified ranges

and balanced side-to-side.

b. Rear tires 8-10 psi recommended (20 psi

MAX.)

c. Front tires 20-25 psi recommended (28 psi

MAX.

2. Verify that the mower does not creep when

the engine is running, the lap bars are in the

neutral position and the parking brake is

released. (Refer to section E-3 on page 21 of

this manual if this condition exists).

3. Recheck the tracking after any adjustments

based on the above.

4. If uneven tracking persists, adjust as follows.

(see Fig. 10)

a. Unit tracks to the RIGHT, adjust Left lap

bar stop bolt to make it longer.

7. If the readings do not correspond to the

ranges in the table, refer to the engine

owner’s manual for the proper adjustment pro-

cedures.

8. If adjustments per the engine operator’s man-

ual do not result in proper RPM readings, con-

tact your service technician.

9. Note: The throttle cable sheath may shrink or

slip over time, changing the relationship

between the throttle lever on the left hand

operator control panel and the throttle arm on

the engine. To readjust the throttle cable:

a. Make sure the engine is off, place lap bars

in the neutral position, set the parking

brake, and disconnect and ground both of

the spark plug wires.

b. Unit tracks to the LEFT, adjust Right lap

bar stop bolt to make it longer.

5. Re-check the tracking and make any fine tun-

ing adjustments to the lap bar stop bolts as

required.

Note:If stop bolt is adjusted too far, track-

ing problem will change sides. Make the fine

tuning adjustments by shortening the same

bolt.

b. Locate and loosen the cable clamp on the

engine throttle plate.

c. Place the operator’s throttle lever to the

high speed position and then slide the

cable through the clamp until the throttle

arm is in the full throttle position. (ref.

engine owner’s manual)

d. Tighten the cable clamp.

e. Move the operator’s throttle lever between

high and low speed and verify that the

engine throttle arm also moves through it’s

full range of motion.

Figure. 10

Lap Bar Stop Bolt

f. Repeat as required to obtain proper throt-

tle adjustment.

g. Verify proper throttle adjustment by check-

ing RPM readings as outlined above.

Download from Www.Somanuals.com. All Manuals Search And Download.

c. Replace the bolts and nuts, and tighten to

28-34 ft-lbs.

C. Deck Corner Ball Wheel Roller Settings

1. Matching the set heights of the ball rollers on

the four corners of the mower deck to the

desired cut height will prevent edge scalping

and minimize any side-to-side variance in cut

height.

2. There are five height adjustment holes in the

bracket that mount the ball rollers to the deck.

a. Use the top set of holes for cut heights of 2

inches or lower.

1. If angular adjustments are also required,

nuts can be tightened until snug at this

point.

d. The same adjustments should be made to

both sides of the mower.

5. To adjust the front-to-rear angle of the lap bars,

a. Loosen the nuts on the lap bar mounting

bolts, leaving the bottom one fairly snug.

b. The top hole is slotted, allowing the lap bar

to pivot on the bottom bolt.

b. Use the middle set of holes for a 2-1/2 - 3-1/2

inch cut height.

c. Use the bottom set of holes for cut heights of

4 inches.

c. Move lap bar to the desired angle and

tighten the nuts to 28-34 ft-lbs.

Note:In the neutral position, the handles of

the lap bars should be aligned with approxi-

mately a one inch gap between the tips. Widen

the gap by adding shim washers to the top

mounting bolt between the lap bar and the

mounting block.

D. Deck Center Anti-Scalp Roller

1. The front roller helps prevent the scalping of

high spots and uneven terrain across the cen-

ter section of the deck.

2. The roller on the front of the deck is fixed at

the factory and can not be adjusted.

d. Check the results of any adjustments to

the conditions described in section a,

above. Repeat any adjustment procedures

as required until all conditions are met.

E. Lap Bar Adjustment

1. Proper lap bar and seat adjustment will result

in the following:

a. In the neutral position with hands on the

lap bars,

1. Operator’s upper arms should be relaxed

and approximately vertical.

2. Operator’s forearms should be approxi-

mately horizontal.

b. In the full forward position,

1. Operator’s back should stay in contact

with the seat back.

2. Lap bars should not contact operator’s

legs.

c. In the full reverse position,

1. Lap bars should not contact the opera-

tor’s legs or torso.

2. Set the seat to the preferred operating position.

a. Adjustment lever is located under the front

edge of the seat.

Figure. 11

Lap Bar Mounting Bolt and Nuts

b. The seat has five inches of front-to-rear

adjustment available.

3. Check factory settings of lap bars for the con-

ditions listed above.

Note:If lap bar adjustments are required,

height adjustments should be made prior to

angular adjustments.

4. To adjust the height of the lap bars,

a. Remove the nuts from the lap bar mounting

bolts (see Fig. 11 ).

b. Remove the bolts and lap bar and reposi-

tion to the second set of holes in the mount-

ing block.

Download from Www.Somanuals.com. All Manuals Search And Download.

F.Deck leveling Procedure

Front

of Unit

Outer Jam Nuts

Trailing Link

1. Park the mower on a flat paved surface, engage

the parking brake, shut off the engine, remove

the key from the ignition switch, disconnect the

spark plug wires and using the lift pedal, posi-

tion the mowing deck into the 3" height of cut

position. (The 3" height of cut position is recom-

mended in order for one to see and obtain a

measurement. Any height of cut position is

acceptable as long as a proper measurement

can be taken.)

jam nut

Left Side

inner Jam Nuts

2. Check the right and left front tire pressure.

Adjust as necessary to 20-25 psi. Tire pressure

can affect blade height by as much as a 1/4”.

3. Check the right and left rear Drive tire pressure.

Adjust as necessary to 8-10 psi.

4. Measure blade-to-ground height at the front tip

of the right blade. To obtain an accurate mea-

sure, align blades in parallel with mower center-

line, (i.e. front to back).

5. Measure blade-to-ground height at the front tip

of the left blade. Be sure to measure at the

blade tip with the blades arranged in proper

position.

Right

Side

Adjustable Lift Link

Figure. 12

6. To level the deck (side to side), place the deck in

the (3” suggested) cutting position. With a 3/4”

wrench loosen the lower jam nut of the left side

of the Lift Link. To adjust the side of the deck up

or down turn the upper jam nut clockwise (to

raise) or counter clockwise (to lower) a few

turns.

7. Measure the blade-to-ground height at the right

rear blade tip. Again be sure to measure at the

blade tip at the rear of the right blade when

aligned along the mower centerline. The blade-

to-ground height at the rear of the blade tip

should be 1/8" to 1/4” (1/8” for 1-1/2” and 1/16”

for 1”) higher than the front tip. This is referred to

as blade pitch. The same height difference

should be true for the left blade, measured front

and back.

8. To change the pitch (front to rear), loosen the

lower nuts on the rear Lift Links. With a few

turns, adjust clockwise (to raise) or counter

clockwise (to lower) the upper nuts of the rear

Lift Links. Once the deck is adjusted, retighten

lower nuts.

9. The final adjustment would be to set the Trailing

Link by adjusting the jam nuts on the threaded

link. Loosen the jam nuts and tighten the inner

nut to achieve the correct length and belt ten-

sion. (see Fig. 12).

10. In many cases it will be necessary to adjust

deck height using both eyebolt adjustments and

pitch adjustment to achieve the correct blade-to-

ground heights. If you remember that the front

right blade tip adjustment is fixed and you level

to that height, adjusting the decks will be simpli-

fied.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRING DIAGRAM

GD: 02003651

Download from Www.Somanuals.com. All Manuals Search And Download.

SLOPE GAUGE

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE RECORD

DATE

WORK PERFORMED

DATE

WORK PERFORMED

Download from Www.Somanuals.com. All Manuals Search And Download.

MANUFACTURER’S LIMITED WARRANTY FOR CUB CADET COMMERCIAL

ENFORCER ZERO-TURN COMMERCIAL RIDING MOWER

IMPORTANT: To obtain warranty coverage owner may be required

present proof of purchase and applicable maintenance records to the

servicing dealer. Please see the operator’s manual for information on

required maintenance and service intervals. In addition, Cub Cadet

may deny warranty coverage if the hour meter, or any part thereof, is

altered, modified, disconnected or otherwise tampered with.

This limited warranty does not provide coverage in the following cases:

Routine maintenance items such as lubricants, filters, blade

sharpening, tune-ups, brake adjustments, clutch adjustments,

deck adjustments, control linkages, drive system, engines,

and normal deterioration of the exterior finish due to use or

exposure.

Service completed by someone other than an authorized

service dealer.

The limited warranty set forth below is given by Cub Cadet LLC with

respect to new merchandise used for commercial and related purposes c.

purchased and used in the United States and/or its territories and

possessions, and by MTD Products Limited with respect to new

merchandise purchased and used in Canada and/or its territories and

For products sold or exported outside of the United States

and/or Canada, and their respective possessions and

territories, except those sold through Cub Cadet’s authorized

channels of export distribution.

possessions (either entity respectively, “Cub Cadet”).

Damage or failure resulting from the use of defective or

improper peplacement parts and\or accessories other than

genuine Cub Cadet parts.

Cub Cadet warrants this product (excluding its No-Fault Components,

and Batteries as described below) against defects in material and

workmanship for a period of two (2) years from the date of original

retail purchase or lease and will, at its option, repair or replace, free of

charge, any part found to be defective in materials or workmanship.

Transportation charges and service calls.

Failure to operate and maintain the product in accordance with

the Operator’s Manual furnished with the product,

Damages and failures resulting from misuse, abuse, neglect,

accident, improper maintenance, alteration, vandalism, theft,

fire, water, or damage because of other peril or natural

disaster.

Batteries have a one-year prorated limited warranty against defects in

material and workmanship, with 100% replacement during the first

three months. After three months, the battery replacement credit is

based on the months remaining in the twelve (12) month period dating

back to the original date of original sale or lease. Any replacement

battery will be warranted only for the remainder of the original warranty

period.

There are no implied warranties, including without limitation any

implied warranty of merchantability or fitness for a particular

purpose. No warranties shall apply after the applicable period of

express written warranty above. No other express warranties

beyond those mentioned above, given by any person or entity,

including a dealer or retailer, with respect to any product, shall

bind Cub Cadet. The exclusive remedy is repair or replacement

of the product as set forth above. The terms of this warranty

provide the sole and exclusive remedy arising from the sale

and/or lease of the products covered hereby. Cub Cadet shall not

be liable for any incidental or consequential loss or damage

including, without limitation, expenses incurred for substitute or

replacement lawn care services or for rental expenses to

temporarily replace a warranted product.

No-Fault Components include only belts, tires, seats and grass bags

which are warranted to be free from defects in material and

workmanship for a period of thirty (30) days from the date of original

purchase or lease.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH

PROOF OF PURCHASE AND APPLICABLE MAINTAINCE

RECORDS, through your local authorized service dealer. To locate the

dealer in your area;

Some jurisdictions do not allow the exclusion or limitation of incidental

or consequential damages, or limitations on how long an implied

warranty lasts, so the above exclusions or limitations may not apply to

you. This limited warranty gives you specific legal rights, and you may

also have other rights that vary in different jurisdictions.

In the U.S.A.:

Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box

361131, Cleveland, Ohio 44136-0019, or call 1-877-282- 8684, or log

on to our Web site at www.cubcadetcommercial.com.

In Canada:

For all provinces excluding Quebec contact Modern Power Products

d/o MTD Canada Ltd. At 60 Ottawa Street South, Kitchener, Ontario

N2G 3S7 or call 1-800-567-6775 or log on to our website at

www.cubcadet.ca.

In no event shall recovery of any kind be greater than the amount of

the purchase price of the product sold. Alteration of safety features

of the product shall void this warranty. You assume the risk and

liability for loss, damage, or injury to you and your property and/or to

others and their property arising out of improper use, misuse or

inability to use the product. This limited warranty shall not extend to

anyone other than the original purchaser/Leasee or to the person for

whom it was purchased or leased as a gift.

In Quebec contact Les Distributions RVI Ltee. d/o MTD Canada Ltd.

2955 jean-Baptiste Deschamps, Ville Lachine, Quebec H8T 1C5 or

call 1-800-361-5770 or log on to our website at www.cubcadet.info.

Cub Cadet LLC - P.O. Box 361131, Cleveland, Ohio 44136-0019; Phone 1-877-282-8684

Form No. 02004994 Rev. 08-0 11/21/2007

Download from Www.Somanuals.com. All Manuals Search And Download.

Agri Fab Lawn Aerator 45 03431 User Manual
Alamo Lawn Mower ST10 User Manual
Bolens Lawn Mower 116 312 000 User Manual
Dixon Lawn Mower ZTR 428 User Guide
Husqvarna Lawn Mower LGT24K54 User Manual
Snapper Lawn Mower 12LTG36 User Guide
Snapper Lawn Mower CAP21509R User Manual
Stiga Lawn Mower 47 S User Guide
Troy Bilt Lawn Mower 13A 344 563 User Guide
Weed Eater Lawn Mower Accessory 532 43 46 60 User Guide