NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE MULTI
PURPOSE FID BENCH
Hardware Identifier
Assembly Instruction
Parts List
SB 680
Warranty
Ordering Parts
Model
SB 680
Retain This
Manual for
Reference
06-05-03
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine be assembled by two or
more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Main Frame (#1) to the Front Stabilizer (#2). Secure it with two M10 x 2 ¾”
Carriage Bolts (#21), one Bracket (#15), two ∅ ¾” Washers (#27), and two M10 Aircraft
Nuts (#28).
B.) Attach the Main Frame (#1) to the Rear Stabilizer (#3). Secure it with two M10 x 2 ¾”
Carriage Bolts (#21), one Bracket (#15), two ∅ ¾” Washers (#27), and two M10 Aircraft
Nuts (#28).
DIAGRAM 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Slide the Sliding Block (#5) onto the Incline Adjustment Bar (#4).
B.) Attach both ends of Incline Adjustment Bar to the open brackets on the Main Frame
(#1). Secure each end with one M10 x 2 ½” Carriage Bolt (#22), Ø ¾” Washer (#27),
and M10 Aircraft Nut (#28).
C.) Use a Lock Knob (#16) to lock the desired incline position.
DIAGRAM 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the lower holes on the Backrest Supports (#7) to the pivot on the Sliding Block
(#5). Secure them with one M12 x 5 ¾” Allen Bolt (#19), two ∅ 1” Washers (#25), and
one M12 Aircraft Nut (#26).
B.) Attach the Seat Support Frame (#6) to the hole on the Backrest Support (#7). Make
sure the Seat Support Frame is on the outside of the Backrest Support. Align the holes
and secure them with one M12 x 2 ½” Allen Bolt (#20), two Ø 1” Washers (#25), and
one M12 Aircraft Nut (#26). Repeat the same step to install the other side. Note: The
Bolt must be inserted from inside of Backrest Support to the outside of the Seat
Support Frame.
C.) Loosen up the Knob Bolt on the Sliding Track to adjust the position so the front end of
the two Seat Support Frames (#6) can be aligned to the pivot on the Main Base Frame
(#1). Secure them with one M12 x 7 5/8” Allen Bolt (#18), two Ø 1” Washers (#25), and
one M12 Aircraft Nut (#26).
DIAGRAM 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Insert the Foam Tube (#10) halfway through the hole on the Main Frame (#1).
Push two Foam Rolls (#12) onto the Foam Tube from both ends. Plug the Foam
Roll End Caps (#11) into the ends.
B.) Place the Seat (#8) onto the Seat Support Frames (#6). Secure it with four M8 x 2”
Allen Bolts (#23) and ∅ 5/8” Washers (#24).
C.) Place the Backrest Board (#9) onto the Backrest Supports (#7). Secure it with four
M8 x 2” Allen Bolts (#23) and ∅ 5/8” Washers (#24).
DIAGRAM 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DIAGRAM
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
Main Frame
Front Stabilizer
Rear Stabilizer
Incline Adjustment Bar
Sliding Block
Seat Support Frame
Backrest Support
Seat
Backrest Board
Foam Tube
Foam Roll End Cap
Foam Roll
Sliding Block Sleeve
2 ¾” x 2” End Cap
Bracket
1
1
1
1
1
2
2
1
1
1
2
2
2
4
2
1
12
1
1
2
4
2
8
8
8
4
6
6
1
1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Lock Knob
1 5/8” x ¾” End Cap
M12 x 7 5/8” Allen Bolt
M12 x 5 ¾” Allen Bolt
M12 x 2 ½” Allen Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M8 x 2” Allen Bolt
∅ 5/8” Washer
Ø 1” Washer
M12 Aircraft Nut
Ø ¾” Washer
M10 Aircraft Nut
#8 Allen Wrench (Tool)
#5 Allen Wrench (Tool)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|