Impex Fitness Equipment SM 6200 User Manual

NOTE:  
Please read all instructions  
carefully before using this  
product  
Table of Contents  
Safety Notice  
MARCY  
DELUXE SMITH MACHINE  
SM-6200  
Hardware Identifier  
Assembly Instruction  
Parts List  
Warranty  
Ordering Parts  
Model  
SM-6200  
Retain This  
Manual for  
Reference  
08-06-09  
OWNER'S  
MANUAL  
IMPEX® INC.  
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746  
Tel: (800) 999-8899 Fax: (626) 961-9966  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRECAUTIONS  
This exercise machine is built for optimum safety. However, certain precautions apply  
whenever you operate a piece of exercise equipment. Be sure to read the entire manual before  
you assemble or operate your machine. In particular, note the following safety precautions:  
1. Keep children and pets away from the machine at all times. DO NOT  
leave children unattended in the same room with the machine.  
2. Only one person at a time should use the machine.  
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal  
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.  
4. Position the machine on a clear, leveled surface. DO NOT use the machine  
near water or outdoors.  
5. Keep hands away from all moving parts.  
6. Always wear appropriate workout clothing when exercising. DO NOT wear  
robes or other clothing that could become caught in the machine. Running  
or aerobic shoes are also required when using the machine.  
7. Use the machine only for its intended use as described in this manual. DO  
NOT use attachments not recommended by the manufacturer.  
8. Do not place any sharp object around the machine.  
9. Disabled person should not use the machine without a qualified person or  
physician in attendance.  
10. Before using the machine to exercise, always do stretching exercises to  
properly warm up.  
11. Never operate the machine if the machine is not functioning properly.  
12. A spotter is recommended during exercise.  
CARE AND MAINTENANCE  
1. Lubricate moving parts with WD-40 or light oil periodically.  
2. Inspect and tighten all parts before using the machine.  
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.  
DO NOT use solvents.  
4. Maximum user’s weight on Bench: 300 lbs.  
5. Maximum weight on the Weight Bar: 300 lbs.  
6. Maximum weight on the Bar Catch: 300 lbs  
7. Maximum weight on Leg Developer: 100 lbs.  
8. Maximum Weight Capacity including user weight: 600 lbs  
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR  
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE  
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL  
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.  
IMPEX INC.  
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY  
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.  
SAVE THESE INSTRUCTIONS.  
2
WARNING LABEL PLACEMENT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The warning labels shown here have been placed on the Cross Brace, Rear Stabilizer and Upper  
Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for  
replacements. Apply the labels in the location shown.  
3
SMITH MACHINE HARDWARE PACK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SMITH MACHINE HARDWARE PACK  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SMITH MACHINE HARDWARE PACK  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SMITH MACHINE ASSEMBLY INSTRUCTION  
Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen  
Wrenches.  
NOTE: It is strongly recommended that two or more people assemble this machine to  
avoid possible injury.  
STEP 1 (See Diagram 1)  
A.) Do not tighten all nuts and bolts until instructed to do so.  
B.) Attach one Base Frame (#1) to the Left Vertical Frame (#3). Attach the Cross Brace (#6)  
to the back of the Left Vertical Frame. Align the holes and secure the Base Frame, Left  
Vertical Frame, and the Cross Brace together with two M10 x 2 3/8” Carriage Bolts (#83),  
Ø ¾” Washers (#89), and M10 Aircraft Nuts (#90). Repeat the same procedure to install  
the other side.  
C.) Attach a Guide Rod (#12) onto the Base Frame (#1). Secure it to the Base Frame with  
one M10 x 1” Allen Bolt (#77) and Ø ¾” Washer (#89) from the bottom.  
D.) Slide one Lower Safety Stop Frame (#17) onto the Guide Rod from the top then slide one  
Safety Stop Frame (#16) onto the Guide Rod.  
E.) Attach a Front Vertical Frame (#2) onto the Base Frame (#1). Secure it with two M10 x 2  
3/8” Carriage Bolts (#83), one 6” x 2 ¾” Bracket (#33), two Ø ¾” Washers (#89), and two  
M10 Aircraft Nuts (#90).  
F.) Attach a Safety Hook (#18) to the Lower Safety Stop Frame (#17). Securely it with one  
M10 x 1” Allen Bolt (#77), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90).  
Attach the Safety Hook onto the selected slot on the back of the Front Vertical Frame.  
G.) Repeat Procedure C through F above to install the other side.  
H.) Place the Front Top Beam (#5) onto the two Front Vertical Frames (#2).  
I.) Insert the top of the Guide Rods (#12) into the holes on the Front Top Beam. Secure each  
Guide Rod to the Front Top Beam with one M10 x 1” Allen Bolt (#77) and Ø ¾” Washer  
(#89).  
J.) Secure each Front Vertical Frame (#2) to the Front Top Beam (#5) with two M10 x 2 3/8”  
Carriage Bolts (#83), one 6” x 2 ¾” Bracket (#33), two Ø ¾” Washers (#89), and two M10  
Aircraft Nuts (#90).  
K.) Secure the Front Top Beam to the Left Vertical Frame (#3) with four M10 x 4” Carriage  
Bolts (#85), two Triangle Brackets (#20), four Ø ¾” Washers (#89), and four M10 Aircraft  
Nuts (#90). Repeat the same procedure to secure the other side.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM 1  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 2 (See Diagram 2)  
A.) Attach the Vertical Frame Base (#9) to the Cross Brace (#6) from the bottom. Attach the  
Rear Vertical Frame (#8) onto the Cross Brace on the top. Align the holes and secure  
them together with two M10 x 2 3/8” Carriage Bolts (#83), Ø ¾” Washers (#89), and M10  
Aircraft Nuts (#90).  
B.) Attach the Backrest Board (#45) to the Rear Vertical Frame (#8). Secure it with two M8 x 2  
3/8” Allen Bolts (#75) and Ø 5/8” Washes (#88).  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 3 (See Diagram 3)  
A.) Attach the Weight Glide Post (#11) to the bracket on the Vertical Frame Base  
(#9). Secure it with one 3 1/8” x 1 ¾” Bracket (#31), M10 x 2 ½” Carriage Bolt  
(#84), Ø ¾” Washer (#89), and M10 Aircraft Nut (#90) to the upper hole, one  
M10 x 2 ½” Allen Bolt (#81) and one Ø ¾” Washer (#89) to the lower hole.  
B.) Slide the Sliding Weight Post (#19) onto the Weight Glide Post (#11)) from the  
top. Make sure the triangular cable connecting bracket on the Sliding Weight  
Post faces up.  
C.)Attach the Upper Frame (#7) onto the Front Top Beam (#5). Secure it with one  
M10 x 4 ½” Allen Bolt (#82), two Ø ¾” Washers (#89), and one M10 Aircraft Nut  
(#90).  
D.)Attach the rear of the Upper Frame (#7) to the top of the Rear Vertical Frame  
(#8). Secure it with one 4 3/8” x 1 ¾” Bracket (#34), M10 x 2 ½” Allen Bolt (#81),  
and Ø ¾” Washer (#89) to the upper hole. Secure the bottom hole with one M10  
x 2 ½” Carriage Bolt (#84), Ø ¾” Washer (#89), and M10 Aircraft Nut (#90).  
E.) Attach the two Cover Brackets (#10) to the Rear Vertical Frame (#8) and Weight  
Glide Post (#11) from both sides.  
F.) Secure the Cover Brackets to the Rear Vertical Frame and Weight Glide Post  
with four M10 x 2 ½” Carriage Bolts (#84), Ø ¾” Washers (#89), and M10 Aircraft  
Nuts (#90).  
G.)Securely tighten all Nuts and Bolts previously installed.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DAIGRAM 3  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 4 (See Diagram 4)  
A.) Attach the Butterfly Base (#37) to the Rear Vertical Frame (#8). Secure it with two M10 x 2  
½” Carriage Bolts (#84), Ø ¾” Washers (#89), and M10 Aircraft Nuts (#90).  
B.) Attach two Swivel Pulley Brackets (#35) to the open brackets on the Rear Vertical Frame  
(#8). Secure each Bracket with one M10 x 2 ½” Allen Bolt (#81), two Ø ¾” Washers (#89),  
and one M10 Aircraft Nut (#90). Do not over tighten the nuts and bolts. Make sure the  
brackets are able to swivel on the bolts.  
C.)Insert the axle on the Left Butterfly (#38) through the holes on the Butterfly Base from the  
bottom. Secure it with one Lock Ring (#47), Ø ¾” Washer (#89), and M10 x ¾” Allen Bolt  
(#76).  
D.)Attach one Butterfly Arm Pad (#43) to the Left Butterfly. Secure it with two M8 x 2 1/8” Allen  
Bolts (#74) and Ø 5/8” Washers (#88).  
E.) Repeat Procedures C & D above to install the other side.  
DIAGRAM 4  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CABLE LOOP DIAGRAM  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 5 (See Diagram 5 & Cable Loop Diagram)  
A.) Attach the 142” Upper Cable (#40) to the front opening on the Upper Frame (#7). Attach a Pulley  
(#59) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#79), two Ø 1 1/8” x 3/8” Pulley  
Bushings (#52), and one M10 Aircraft Nut (#90). Make sure the ball stopper on the Cable is  
underneath the Frame.  
B.) Draw the Cable over the Pulley along the Upper Frame to the opening in between the two Cover  
Brackets (#10). Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#81), two  
Ø 1” x 5/8” Pulley Bushings (#51), one L-shaped Cable Retainer (#30) and M10 Aircraft Nut (#90).  
C.)Draw the Cable around the Pulley then downward. Attach a Pulley in between the two Double  
Floating Pulley Brackets (#21). Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#78), two Ø ¾”  
Washers (#89), and one M10 Aircraft Nut (#90). Let the Bracket hanging for now.  
D.)Draw the Cable around the Pulley then up to the opening on top of the Weight Glide Post (#11).  
Attach a Pulley (#59) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#80), two Ø 1” x  
½” Pulley Bushings (#50), and one M10 Aircraft Nut (#90).  
E.) Draw the Cable around the Pulley then down to the Sliding Weight Post (#19). Secure the Cable  
to the Sliding Weight Post with one M10 x 1” Allen Bolt (#77), two Ø ¾” Washers (#89), and one  
M10 Aircraft Nut (#90). Attach two Olympic Sleeves (#60) to the Sliding Weight Post. Attach two  
Spring Clips (#73) to the Sleeves.  
F.) Connect the Lat Bar (#27) to the Cable with a Short Chain (#70) and two C-Clips (#72).  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 6 (See Diagram 6 & Cable Loop Diagram)  
A.) Attach one end of the 86” Butterfly Cable (#42) to the clip on the Right Butterfly (#39). Draw  
the Cable to the right open Swivel Pulley Bracket (#35).  
B.) Attach a Small Pulley (#58) to the Swivel Pulley Bracket. Secure it with one M10 x 1 ¾” Allen  
Bolt (#78), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90).  
C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating  
Pulley Bracket (#36). Install a Pulley (#59) to the Bracket. Secure it with one M10 x 1 ¾”  
Allen Bolt (#78), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90).  
D.) Let the Bracket hanging for now.  
E.) Draw the Cable upward to the left open Swivel Pulley Bracket. Repeat Procedure B above to  
install another Small Pulley.  
F.) Draw the Cable around the Pulley they clip the end to the Left Butterfly (#38).  
DIAGRAM 6  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 7 (See Diagram 7 & Cable Loop Diagram)  
A.) Insert the tip of the 127” Lower Cable (#41) through the opening on the Foot Plate (#26)  
to the opening on the Vertical Frame Base (#9).  
B.) Attach a Small Pulley (#58) to the opening. Attach the Foot Plate to the Frame. Align the  
holes and secure the Foot Plate, Vertical Frame Base, and the Small Pulley with one M10  
x 2 ¾” Allen Bolt (#93), two Ø 1” x ¾” Pulley Bushings (#53), and one M10 Aircraft Nut  
(#90). Secure the Foot Plate to the Vertical Frame Base with one M10 x 2 ½” Carriage  
Bolt (#84), Ø ¾” Washer (#89), and M10 Aircraft Nut (#90).  
C.)Draw the Cable underneath the Pulley to the open bracket on the Vertical Frame Base.  
Install a Pulley (#59) with a M10 x 1 ¾” Allen Bolt (#78), two Ø ¾” Washers (#89) and one  
M10 Aircraft Nut (#90).  
D.)Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket  
(#21) previously installed in Step-5. Install another Pulley with one M10 x 1 ¾” Allen Bolt  
(#78), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90). Note: After finishing the  
entire cable assembly, come back to this step and adjust the tension of the cables. To  
increase the tension, move up the Pulley on the Double Floating Pulley Brackets. To  
decrease the tension, move the Pulley down.  
E.) Draw the Cable around the Pulley then downward to the open bracket on the back of the  
Rear Vertical Frame (#8). Install another Pulley.  
F.) Draw the Cable around the Pulley and upward to the Single Floating Pulley Bracket (#36)  
previously installed in Step-6. Secure the Cable to the Bracket with one M10 x 1” Allen  
Bolt (#77), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90).  
G.)Connect the Long Chain (#71) to the Cable with a C-clip (#72). Depends on the exercise,  
connect the Shiver Bar (#29), Ankle Strap (#91), or Single Handle (#92) to the Long  
Chain with another C-clip.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM 7  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 8 (See Diagram 8)  
A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting  
Sleeve (#13) in between the two Safety Stop Frames (#16). Align the holes and insert the  
Weight Bar (#15) all the way through. Center the bar and use the two M8 x 3/8” Allen Bolts  
(#86) on the two Safety Stop Frame to secure the Weight Bar on each side.  
B.) Turn the safety catch hook forward on the Lifting Sleeve to secure its position on the  
selected holes on the Front Vertical Frames (#2). Attach a Long Olympic Sleeve (#61) to  
each end of the Weight Bar. Attach a Spring Clip (#73) to the Sleeve.  
C.)Attach six Weight Posts (#14) to the Left & Right Vertical Frames (#3 & 4). Secure each  
Weight Post with one M10 x ¾” Allen Bolt (#76) and Ø ¾” Washer (#89).  
D.)Attach six Olympic Sleeves (#60) to the Weight Posts. Attach six Spring Clips (#73) to the  
sleeves. Insert the Left & Right Bar Holders (#24 & 25), the Left & Right Safety Catches  
(#22 & 23) into the selected holes on the Front Vertical Frames.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SMITH CAGE EXPLODED DIAGRAM  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SMITH CAGE PARTS LIST  
KEY NO.  
DESCRIPTION  
Q’ty  
1
2
3
4
5
6
7
8
9
Base Frame  
Front Vertical Frame  
Left Vertical Frame  
Right Vertical Frame  
Front Top Beam  
Cross Brace  
Upper Frame  
Rear Vertical Frame  
Vertical Frame Base  
2
2
1
1
1
1
1
1
1
2
1
2
1
6
1
2
2
2
1
4
2
1
1
1
1
1
1
1
1
1
1
1
4
1
2
1
1
1
1
1
1
1
2
1
1
2
2
4
4
2
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
Ø 1” x 5/8” Pulley Bushing  
Ø 1 1/8” x 3/8” Pulley Bushing  
Ø 1” x ¾” Pulley Bushing  
1 ½” Sleeve  
5 ¾” x 2” Rubber Bumper  
3 3/8” 2” Rubber Bumper  
6” Handle Grip  
Small Pulley  
Pulley  
Olympic Sleeve  
Long Olympic Sleeve  
Ø 1 ½” Con-shaped End Cap  
1 ¾” End Cap  
2” Square End Cap  
2” x 1 ¾” End Cap  
1 ½” Square End Cap  
Ø 1” End Cap  
Ø 1 ½” x 1” Bushing  
Ø 1 ½” Washer  
Short Chain  
2
2
2
4
2
2
4
3
8
8
2
2
2
1
2
1
10  
2
1
1
1
4
10  
4
2
8
8
7
1
1
5
1
14  
8
8
2
10 Cover Bracket  
11 Weight Glide Post  
12 Guide Rod  
13 Lifting Sleeve  
14 Weight Post  
15 Weight Bar  
16 Safety Stop Frame  
17 Lower Safety Stop Frame  
18 Safety Hook  
19 Sliding Weight Post  
20 Triangle Bracket  
21 Double Floating Pulley Bracket  
22 Left Safety Catch  
23 Right Safety Catch  
24 Left Bar Holder  
25 Right Bar Holder  
26 Foot Plate  
27 Lat Bar  
28 Shiver Bar Handle  
29 Shiver Bar  
30 L-shaped Cable Retainer  
31 3 1/8” x 1 ¾” Bracket  
32 4 3/8” x 1 ¾” Bracket  
33 6” x 2 ¾” Bracket  
34 4 3/8” x 1 ½” Bracket  
35 Swivel Pulley Bracket  
36 Single Floating Pulley Bracket  
37 Butterfly Base  
Long Chain  
Hook  
Spring Clip  
M8 x 2 1/8” Allen Bolt  
M8 x 2 3/8” Allen Bolt  
M10 x ¾” Allen Bolt  
M10 x 1” Allen Bolt  
M10 x 1 ¾” Allen Bolt  
M10 x 2 1/8” Allen Bolt  
M10 x 2 3/8” Allen Bolt  
M10 x 2 ½” Allen Bolt  
M10 x 4 ½” Allen Bolt  
M10 x 2 3/8” Carriage Bolt  
M10 x 2 ½” Carriage Bolt  
M10 x 4” Carriage Bolt  
M8 x 3/8” Allen Bolt  
ST2.9 Screw  
Ø 5/8” Washer  
Ø ¾” Washer  
M10 Aircraft Nut  
Ankle Strap  
Single Handle  
M10 x 2 ¾” Allen Bolt  
8
6
72  
48  
1
38 Left Butterfly  
39 Right Butterfly  
40 142” Upper Cable  
41 127” Lower Cable  
42 86” Butterfly Cable  
43 Butterfly Arm Pad  
44 Decal  
45 Backrest Board  
46 Ø 1 1/8” x 1 1/8” Rubber Bumper  
47 Lock Ring  
1
1
48 Ø 2” x Ø 1 ½” Bushing  
49 Safety Stop Frame Sleeve  
50 Ø 1” x ½” Pulley Bushing  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULTI-PURPOSE BENCH HARDWARE PACK  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION  
Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen  
Wrenches. NOTE: It is strongly recommended that this machine be assembled by two or  
more people to avoid possible injury.  
STEP 1 (See Diagram 1)  
A.) Attach the Left & Right Rear Stabilizer (#2 & #3) to the Main Frame (#1) from each side.  
B.) Secure them together with two M10 x 2 3/8” Carriage Bolts (#37) from bottom, one 3” x 2”  
Bracket (#14), two Ø ¾” Washers (#44), and two M10 Aircraft Nuts (#47).  
C.)Secure them together with two M10 x 4” Carriage Bolts (#36), two Ø ¾” Washers (#44), and  
two M10 Aircraft Nuts (#47) from the side.  
DIAGRAM 1  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 2 (See Diagram 2)  
A.) Align the bracket on the Backrest Adjustment Support (#6) in between the two  
Backrest Supports (#12). Secure it with four M8 x 1 5/8” Allen Bolts (#40), eight Ø 5/8”  
Washers (#45), and four M8 Aircraft Nuts (#48). Do not tighten the Nuts and Bolts  
yet.  
B.) Insert the Backrest Adjustment Support (#6) into the opening on the Main Frame (#1).  
Press or step down on the Backrest Adjustment Lever (#9) to allow the Support to go  
through.  
C.)Attach the Seat Bracket (#5) to the pivot on the Main Frame. Attach the bottom side-  
holes on the Backrest Supports (#12) to the Seat Bracket. Align the holes. Secure  
them together with one M12 x 6 ¾” Allen Bolt (#38), two Ø 1” Washers (#43), and one  
M12 Aircraft Nut (#46).  
D.)Securely tighten all Nuts and Bolts installed.  
DIAGRAM 2  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 3 (See Diagram 3)  
A.) Place the Seat Pad (#17) onto Seat Bracket (#5). Secure it with four M8 x 1 3/8” Allen Bolts  
(#41) and Ø 5/8” Washers (#45).  
B.) Attach the Backrest Board (#16) to the two Backrest Supports (#12). Secure it with four M8 x 1  
3/8” Allen Bolts (#41) and Ø 5/8” Washers (#45).  
C.)When adjusting the Backrest Board to an incline position, simply pull up the Board. When  
adjusting the Board to a decline position, press or step down on the Backrest Adjustment Lever  
(#9) to disengage the Lever to allow the Board to go down.  
D.)Attach the Arm Curl Pad (#18) to the Arm Curl Stand (#7). Secure it with two M8 x 5/8” Allen  
Bolts (#42) and two Ø 5/8” Washers (#45).  
E.) Insert the Arm Curl Stand into the Leg Developer holder on the Main Frame (#1). Use the M18  
Lock Knob (#27) to lock the Stand at desired position.  
DIAGRAM 3  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 4 (See Diagram 4)  
A.) Attach the Leg Developer (#4) to the open bracket on the Leg Developer holder on Main  
Frame (#1). Secure it with an Axle (#15), two M10 x 5/8” Allen Bolts (#35), and two Ø ¾”  
Washers (#44).  
B.) Insert two Foam Tubes (#13) halfway through the holes on the Leg Developer. Push four  
Foam Rolls (#22) onto the Tubes from both sides. Plug four Foam Roll End Caps (#28) into  
the ends of the Tubes.  
C.)Attach an Olympic Sleeve (#26) onto the weight post on the Leg Developer. Attach a Spring  
Clip (#20) to the Olympic Sleeve.  
D.)Attach the Curl Bar Handle Support (#8) to the Leg Developer. Secure it with a Lock Pin  
(#11).  
E.) Remove the Curl Bar Handle Support when doing Leg Developer exercises.  
DIAGRAM 4  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULTI-PURPOSE BENCH PARTS LIST  
KEY NO.  
1
2
3
4
5
6
7
8
DESCRIPTION  
Main Frame  
Left Rear Stabilizer  
Right Rear Stabilizer  
Leg Developer  
Seat Bracket  
Backrest Adjustment Support  
Arm Curl Stand  
Curl Bar Handle Support  
Backrest Adjustment Lever  
¾” Curl Bar Support End Cap  
Lock Pin  
Backrest Support  
Foam Tube  
3” x 2” Bracket  
Axle  
Backrest Board  
Seat Pad  
Arm Curl Pad  
2” x 1 ¾” Sleeve  
Spring Clip  
Spring  
Foam Roll  
Q’ty  
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
4
2
1
2
1
1
4
1
4
2
2
1
2
2
2
2
1
1
4
8
2
2
8
18  
1
5
4
1
1
1
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
Ø 2” End Cap  
Ø 1 ¼” x 1 3/8” End Cap  
Ø 1” x 3/8” Bushing  
Olympic Sleeve  
M18 Lock Knob  
Foam Roll End Cap  
Ø 1” End Cap  
1” Square End Cap  
Ø 2” Leg Developer Bushing  
3 1/8” x 1 5/8” End Cap  
Lever Cover  
6” Grip  
M10 x 5/8” Allen Bolt  
M10 x 4” Carriage Bolt  
M10 x 2 3/8” Carriage Bolt  
M12 x 6 ¾” Allen Bolt  
M10 x 2 ½” Allen Bolt  
M8 x 1 5/8” Allen Bolt  
M8 x 1 3/8” Allen Bolt  
M8 x 5/8” Allen Bolt  
Ø 1” Washer  
Ø ¾” Washer  
Ø 5/8” Washer  
M12 Aircraft Nut  
M10 Aircraft Nut  
M8 Aircraft Nut  
#6 Allen Wrench (Tool)  
#5 Allen Wrench (Tool)  
#4 Allen Wrench (Tool)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPEX® INC.  
LIMITED WARRANTY  
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal  
use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty  
extends only to the original purchaser.  
repairing, at IMPEX's option.  
IMPEX's obligation under this Warranty is limited to replacing or  
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer  
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the  
customer. This warranty does not extend to any product or damage to a product caused by or attributable to  
freight damage, abuse, misuse, improper or abnormal usage or repairs. No other warranty beyond that  
specifically set forth above is authorized by IMPEX.  
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection  
with the use or performance of the product or other damages with respect to any economic loss, loss of property,  
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential  
damages or whatsoever natures.  
Some states do not allow the exclusion or limitation of incidental or  
consequential damages. Accordingly, the above limitation may not apply to you.  
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of  
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.  
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation  
may not apply to you.  
This warranty gives you specific legal right. You may also have other rights which vary from state to state.  
IMPEX® INC.  
14777 Don Julian  
City of Industry, CA 91746  
ORDERING REPLACEMENT PARTS  
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899  
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.  
When ordering replacement parts, always give the following information.  
1.Model  
2.Description of Parts  
3.Part Number  
4.Date of Purchase  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Baby Accessories ISPS040AB User Manual
Grizzly Hunting Equipment H5844 User Manual
Grizzly Planer G1017 User Manual
Hasbro Games Talking Game User Manual
Hearth and Home Technologies Fan GFK4B User Manual
HP Hewlett Packard Printer 1022 User Manual
HP Hewlett Packard Router t5730 User Manual
Hunter Fan Ventilation Hood 82001 User Manual
IBM Computer Monitor 31P6259 User Manual
Impex Fitness Equipment MD 823 User Manual