Operator′s manual
223R
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Contents
Note the following before starting:
KEY TO SYMBOLS
Please read the operator’s manual carefully.
Symbols .......................................................................
CONTENTS
WARNING! Long-term exposure to noise can
result in permanent hearing impairment. So
always use approved hearing protection.
Contents ......................................................................
Note the following before starting: ................................
INTRODUCTION
!
!
Dear Customer, ............................................................
WHAT IS WHAT?
5
WARNING! Under no circumstances may the
design of the machine be modified without
the permission of the manufacturer. Always
use genuine accessories. Non-authorized
modifications and/or accessories can result
in serious personal injury or the death of the
operator or others.
What is what on the clearing saw? ..............................
GENERAL SAFETY PRECAUTIONS
Important ......................................................................
Personal protective equipment .....................................
Machine′s safety equipment ........................................
Cutting equipment ........................................................
ASSEMBLY
WARNING! A clearing saw, brushcutter or
trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.
Fitting the handlebar .................................................... 11
Fitting blades and trimmer heads ................................. 11
Fitting a blade guard, grass blade and grass cutter ..... 12
!
Fitting a trimmer guard and Superauto II 1” trimmer
head ............................................................................. 12
Fitting other guards and cutting attachments ............... 13
Adjusting the harness and clearing saw ...................... 13
Standard harness ........................................................ 13
FUEL HANDLING
Fuel safety ................................................................... 14
Fuel .............................................................................. 14
Fuelling ........................................................................ 15
STARTING AND STOPPING
Check before starting ................................................... 16
Starting and stopping ................................................... 16
WORKING TECHNIQUES
General working instructions ....................................... 18
MAINTENANCE
Carburettor ................................................................... 20
Muffler .......................................................................... 22
Cooling system ............................................................ 22
Bevel gear .................................................................... 22
Air filter ......................................................................... 23
Drive shaft .................................................................... 23
Spark plug .................................................................... 23
Maintenance schedule ................................................. 24
TECHNICAL DATA
Technical data .............................................................. 25
EC-declaration of conformity ........................................ 26
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear Customer,
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the
Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.The
location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During the
more than 300 years of beeing, the Husqvarna factory has produced a lot of different products, from wood stoves to modern kitchen
appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first motor driven lawn mowers appeared, followed by chain
saws in 1959, and it is within this area Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority.
The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for
building and construction industry. Husqvarna′s aim is also to be in the front edge according to ergonomics, usability, security and
environmental protection. That is the reason why we have developed many different features to provide our products within these
areas.
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to
come. The purchase of one of our products gives you access to professional help with repairs and service whenever this may be
necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the address of your nearest service
workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s
manual as a valuable document.By following its′ content (using, service, maintenance etc) the life span and the second-hand value
of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator′s manual.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
What is what on the clearing saw?
1
2
3
4
5
6
7
8
9
Blade
17 Handle adjustment
Grease filler cap, bevel gear
Bevel gear
18 Locking nut
19 Support flange
20 Support cup
Cutting attachment guard
Shaft
21 Drive disc
Handlebar
22 Trimmer head
23 Socket spanner
24 Operator′s manual
25 Transport guard
26 Allen key
Throttle control
Stop switch
Throttle lockout
10 Suspension ring
11 Cylinder cover
12 Starter handle
13 Fuel tank
27 Locking pin
28 Harness
29 Start throttle button
30 Adjusting the throttle wire
31 Spark plug cap and spark plug
14 Choke control
15 Air purge
16 Air filter cover
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Important
Personal protective equipment
IMPORTANT!
IMPORTANT!
The machine is only designed for trimming grass.
A clearing saw, brushcutter or trimmer can be dangerous if
used incorrectly or carelessly, and can cause serious or
fatal injury to the operator or others. It is extremely
important that you read and understand the contents of this
operator’s manual.
The only accessories you can operate with this engine unit
are the cutting attachments we recommend in the chapter
on Technical data.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect your
vision, your judgement or your co-ordination.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen. Ask
your dealer for help in choosing the right equipment.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
Never use a machine that has been modified in any way
from its original specification.
WARNING! Listen out for warning signals or
shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual.Some maintenance and service measures must be
carried out by trained and qualified specialists. See
instructions under the heading Maintenance.
!
HELMET
A protective helmet where there is a risk of falling objects
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition lead
are undamaged to avoid the risk of electric shock.
The machine operator must ensure that no people or
animals come closer than 15 metres while working. When
several operators are working in the same area the safety
distance should be at least twice the tree height and no less
than 15 metres.
HEARING PROTECTION
Wear hearing protection that provides adequate noise
reduction.
WARNING! The ignition system of this
machine produces an electromagnetic field
during operation.This field may under some
!
circumstances interfere with pacemakers.To
reduce the risk of serious or fatal injury, we
recommend persons with pacemakers to
consult their physician and the pacemaker
manufacturer before operating this machine.
EYE PROTECTION
Always wear approved eye protection. If you use a visor then
you must also wear approved protective goggles. Approved
protective goggles must comply with standard ANSI Z87.1 in
the USA or EN 166 in EU countries.
WARNING! Running an engine in a confined
or badly ventilated area can result in death
due to asphyxiation or carbon monoxide
poisoning.
!
GLOVES
WARNING! Never allow children to use or be
in the vicinity of the machine. As the
machine is equipped with a spring-loaded
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
!
stop switch and can be started by low speed
and force on the starter handle, even small
children under some circumstances can
produce the force necessary to start the
machine.This can mean a risk of serious
personal injury.Therefore remove the spark
plug cap when the machine is not under
close supervision.
BOOTS
Wear boots with steel toe-caps and non-slip sole.
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
CLOTHING
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Wear clothes made of a strong fabric and avoid loose clothing
that can catch on twigs and branches. Always wear heavy,
long pants. Do not wear jewellery, shorts sandals or go
barefoot. Secure hair so it is above shoulder level.
FIRST AID KIT
Always have a first aid kit nearby.
Press the throttle lockout and make sure it returns to its
original position when you release it.
Machine′s safety equipment
This section describes the machine′s safety equipment, its
purpose, and how checks and maintenance should be carried
out to ensure that it operates correctly. See the ”What is
what?” section to locate where this equipment is positioned
on your machine.
Check that the throttle control and throttle lockout move freely
and that the return springs work properly.
The life span of the machine can be reduced and the risk of
accidents can increase if machine maintenance is not carried
out correctly and if service and/or repairs are not carried out
professionally. If you need further information please contact
your nearest service workshop.
IMPORTANT! All servicing and repair work on the machine
requires special training. This is especially true of the
machine′s safety equipment.If your machine fails any of the
checks described below you must contact your service
agent.When you buy any of our products we guarantee the
availability of professional repairs and service. If the retailer
who sells your machine is not a servicing dealer, ask him for
the address of your nearest service agent.
See instructions under the heading Start. Start the machine
and apply full throttle. Release the throttle and check that the
cutting attachment stops and remains at a standstill. If the
cutting attachment rotates with the throttle in the idle position
then the carburettor idle setting must be checked. See
instructions under the heading Maintenance.
WARNING! Never use a machine with faulty
safety equipment.The machine’s safety
equipment must be checked and maintained
as described in this section. If your machine
fails any of these checks contact your
service agent to get it repaired.
!
Throttle lockout
Stop switch
The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the lock (A)
(i.e.when you grasp the handle) it releases the throttle control
(B). When you release the handle the throttle control and the
throttle lockout both move back to their original positions.This
movement is controlled by two independent return springs.
This arrangement means that the throttle control is
automatically locked at the idle setting.
Use the stop switch to switch off the engine.
A
Start the engine and make sure the engine stops when you
move the stop switch to the stop setting.
B
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Cutting attachment guard
WARNING! Overexposure to vibration can
lead to circulatory damage or nerve damage
in people who have impaired circulation.
Contact your doctor if you experience
symptoms of overexposure to vibration.
Such symptoms include numbness, loss of
feeling, tingling, pricking, pain, loss of
strength, changes in skin colour or
!
This guard is intended to prevent loose objects from being
thrown towards the operator. The guard also protects the
operator from accidental contact with the cutting attachment.
condition.These symptoms normally appear
in the fingers, hands or wrists.The risk
increases at low temperatures.
Quick release
There is an easily accessible, quick release fitted at the front
as a safety precaution in case the engine catches fire, or in
any other situation that requires you to free yourself from the
machine and harness. See instructions under the heading
Adjusting the harness and clearing saw.
Check that the guard is undamaged and not cracked.Replace
the guard if it has been exposed to impact or is cracked.
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
!
Check that the harness straps are correctly positioned. Once
the harness and machine have been adjusted, check that the
harness quick release works correctly.
Vibration damping system
Muffler
Your machine is equipped with a vibration damping system
that is designed to minimize vibration and make operation
easier.
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user. A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
Using incorrectly wound cord or a blunt or incorrect cutting
attachment (wrong type or incorrectly filed, see instructions
under the heading Filing the blade) increases the level of
vibration.
In countries that have a warm and dry climate there is a
significant risk of fire. We therefore fit certain mufflers with a
spark arrestor mesh. Check whether the muffler on your
machine is fitted with this kind of mesh.
The machine′s vibration damping system reduces the transfer
of vibration between the engine unit/cutting equipment and
the machine′s handle unit.
Regularly check the vibration damping units for cracks or
deformation. Check that the vibration damping element is
undamaged and securely attached.
For mufflers it is very important that you follow the instructions
on checking, maintaining and servicing your machine.
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Never use a machine that has a faulty muffler.
Locking nut
A locking nut is used to secure some types of cutting
attachment.
Regularly check that the muffler is securely attached to the
machine.
When fitting, tighten the nut in the opposite direction to the
direction of rotation of the cutting attachment. To remove it,
undo the nut in the same direction as the cutting attachment
rotates. (CAUTION! The nut has a left-hand thread.) Tighten
the nut using the socket spanner.
If the muffler on your machine is fitted with a spark arrestor
mesh this must be cleaned regularly. A blocked mesh will
cause the engine to overheat and may lead to serious
damage.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
The nylon lining inside the locking nut must not be so worn
that you can turn it by hand. The lining should offer a
resistance of at least 1.5 Nm. The nut should be replaced
after it has been put on approx. 10 times.
!
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
WARNING! The inside of the muffler contain
chemicals that may be carcinogenic. Avoid
contact with these elements in the event of a
damaged muffler.
•
•
•
Reduce the risk of blade thrust.
!
Obtain maximum cutting performance.
Extend the life of cutting equipment.
WARNING! Bear in mind that:
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
!
The exhaust fumes from the engine are hot
and may contain sparks which can start a
fire. Never start the machine indoors or near
combustible material!
Refer to the instructions for the cutting attachment to check
the correct way to load the cord and the correct cord
diameter.
Keep the teeth of the blade correctly sharpened! Follow our
recommendations. Also refer to the instructions on the
blade packaging.
Maintain the correct blade setting! Follow our instructions
and use the recommended file gauge.
WARNING! Always stop the engine before
doing any work on the cutting attachment.
This continues to rotate even after the
throttle has been released. Ensure that the
cutting attachment has stopped completely
and disconnect the HT lead from the spark
plug before you start to work on it.
!
WARNING! Using an incorrect cutting
attachment or an incorrectly sharpened
blade increases the risk of blade thrust.
!
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Cutting equipment
Sharpening grass cutters and grass
blades
Grass blades and grass cutters are intended for cutting
coarse grass.
•
•
See the cutting attachment packaging for correct
sharpening instructions. Sharpen blades and cutters
using a single-cut flat file.
A trimmer head is intended for trimming grass.
Sharpen all edges equally to maintain the balance of the
blade.
General rules
WARNING! Always discard a blade that is
bent, twisted, cracked, broken or damaged
in any other way. Never attempt to straighten
a twisted blade so that it can be reused. Only
use original blades of the specified type.
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
!
Trimmer head
Keep the teeth of the blade correctly sharpened! Follow our
instructions and use the recommended file gauge. An
incorrectly sharpened or damaged blade increases the risk of
accidents.
IMPORTANT!
Always ensure the trimmer cord is wound tightly and evenly
around the drum, otherwise the machine will generate
harmful vibration.
•
Only use the recommended trimmer heads and trimmer
cords.These have been tested by the manufacturer to suit
a particular engine size.This is especially important when
a fully automatic trimmer head is used. Only use the
recommended cutting attachment. See the chapter on
Technical data.
Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be replaced.
•
•
Smaller machines generally require small trimmer heads
and vice versa. This is because when clearing using a
cord the engine must throw out the cord radially from the
trimmer head and overcome the resistance of the grass
being cleared.
The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of the
same diameter.
•
•
Make sure that the cutter on the trimmer guard is intact.
This is used to cut the cord to the correct length.
To increase the life of the cord it can be soaked in water
for a couple of days.This will make the line tougher so that
it lasts longer.
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fitting the handlebar
Fitting blades and trimmer heads
•
Remove the screw at the rear of the throttle handle.
WARNING!
•
Slide the throttle handle onto the right side of the
handlebar, (see diagram).
!
When fitting the cutting attachment it is
extremely important that the raised section
on the drive disc/support flange engages
correctly in the centre hole of the cutting
attachment. If the cutting attachment is fitted
incorrectly it can result in serious and/or
fatal personal injury.
•
Align the screw hole in the throttle handle with the hole in
the handlebar.
•
•
Refit the screw in the hole in the rear of the throttle handle.
Screw the screw through the handle and handlebar.
Tighten it.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
!
•
Fit the mounting components as shown.
IMPORTANT! If a saw blade or grass blade are to be used
the machine must be equipped with the correct handlebar,
blade guard and harness.
•
The handle mounting must be fitted between the arrows
on the shaft.
•
•
Loosely tighten the four screws.
Put on the harness and hang the machine from the
support hook. Now make a final adjustment so that the
machine is in a comfortable working position when it
hangs from the harness. Tighten the screws.
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fitting a blade guard, grass blade
and grass cutter
Fitting a trimmer guard and
Superauto II 1” trimmer head
K
G
F
E
G
K
F
B
I
C
J
D
I
A
B
A
C
•
Fit the correct trimmer guard (A) for use with the trimmer
head. Hook the trimmer guard/combination guard onto
the fitting on the shaft and secure with the bolt (L).
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
Hook the blade guard/combination guard (A) onto the
fitting on the shaft and secure with the bolt.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
CAUTION! Use the recommended blade guard. See the
Technical data section.
To fit the trimmer head, first separate the two halves (see
diagram). Proceed as follows:
•
•
Fit the drive disc (B) on the output shaft.
Insert a finger into the centre hole of the cover (I) while
grasping the cover with your other fingers.Using the index
finger and thumb of your other hand, release the two
catches (J) that engage in the cut-outs in the bottom half
(K). Pull apart the trimmer head, grasping the cover firmly.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Place the blade (D), support cup (E) and support flange
(F) on the output shaft.
•
•
Place the cover (I) and the support flange (F) on the
output shaft.
•
Fit the nut (G). The nut must be tightened to a torque of
35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool
kit. Hold the shaft of the spanner as close to the blade
guard as possible. To tighten the nut, turn the spanner in
the opposite direction to the direction of rotation (Caution!
left-hand thread).
Fit the nut (G). Tighten the nut to a torque of 35-50 Nm
(3.5-5 kpm). Use the socket spanner in the tool kit. Grasp
the handle of the spanner as close to the trimmer guard
as possible.
•
To tighten the nut, turn the spanner in the opposite
direction to the direction of rotation (Caution! left-hand
thread).
•
Fit the bottom half of the trimmer head (K) to the cover (I)
by pressing them together, with the cut-outs on the bottom
half aligned with the catches on the cover.
•
To dismantle, follow the instructions in the reverse order.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Spreading the load on your shoulders
Fitting other guards and cutting
attachments
A well-adjusted harness and machine makes work much
easier. Adjust the harness for the best working position.
Tension the side straps so that the weight is evenly distributed
across both shoulders.
•
Fit the trimmer guard/combination guard (A) intended for
use with the trimmer head/plastic blades. Hook the guard
onto the fitting on the shaft and secure it with the bolt (L).
Correct height
Adjust the shoulder strap so that the cutting attachment is
parallel to the ground.
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
H
Correct balance
Let the cutting attachment rest lightly on the ground. Adjust
the position of the suspension ring to balance the clearing
saw correctly.
H
•
To dismantle, follow the instructions in the reverse order.
Adjusting the harness and clearing
saw
WARNING! When using a clearing saw it
must always be hooked securely to the
harness. Otherwise you will be unable to
control the clearing saw safely and this can
result in injury to yourself or others. Never
use a harness with a defective quick release.
!
Standard harness
Quick release
At the front is an easily accessible, quick release. Use this if
the engine catches fire or in any other emergency situation
that requires you to free yourself from the machine and
harness.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Petrol
Fuel safety
Never start the machine:
1
2
If you have spilt fuel on it. Wipe off the spillage and allow
remaining fuel to evaporate.
CAUTION! Always use a quality petrol/oil mixture at least 90
octane (RON). If your machine is equipped with a catalytic
converter (see chapter on Technical data) always use a good
quality unleaded petrol/oil mixture. Leaded petrol will destroy
the catalytic converter.
If you have spilt fuel on yourself or your clothes, change
your clothes.Wash any part of your body that has come in
contact with fuel. Use soap and water.
3
If the machine is leaking fuel. Check regularly for leaks
from the fuel cap and fuel lines.
Use low-emission petrol, also known as alkylate petrol, if it is
available.
Transport and storage
•
Store and transport the machine and fuel so that there is
no risk of any leakage or fumes coming into contact with
sparks or naked flames, for example, from electrical
machinery, electric motors, electrical relays/switches or
boilers.
•
•
The lowest octane recommended is 90 (RON). If you run
the engine on a lower octane grade than 90 so-called
knocking can occur. This gives rise to a high engine
temperature, which can result in serious engine damage.
•
•
When storing and transporting fuel always use approved
containers intended for this purpose.
When storing the machine for long periods the fuel tank
must be emptied. Contact your local petrol station to find
out where to dispose of excess fuel.
When working at continuous high revs a higher octane
rating is recommended.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
Two-stroke oil
The transport guard must always be fitted to the cutting
attachment when the machine is being transported or in
storage.
•
For best results and performance use HUSQVARNA two-
stroke engine oil, which is specially formulated for our air-
cooled two-stroke engines.
•
In order to prevent unintentional starting of the engine, the
spark plug cap must always be removed during long-term
storage, if the machine is not under close supervision and
when performing all service measures.
•
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
•
•
Never use oil intended for four-stroke engines.
A poor oil quality and/or too high oil/fuel ratio may
jeopardise function and decrease the life time of catalytic
converters.
WARNING! Take care when handling fuel.
Bear in mind the risk of fire, explosion and
inhaling fumes.
!
•
Mixing ratio
1:50 (2%) with HUSQVARNA two-stroke oil.
Fuel
1:33 (3%) with oils class JASO FB or ISO EGB formulated
for air-cooled, two-stroke engines.
CAUTION! The machine is equipped with a two-stroke
engine and must always been run using a mixture of petrol
and two-stroke engine oil. It is important to accurately
measure the amount of oil to be mixed to ensure that the
correct mixture is obtained. When mixing small amounts of
fuel, even small inaccuracies can drastically affect the ratio of
the mixture.
Two-stroke oil, litre
Petrol, litre
2% (1:50)
0,10
3% (1:33)
0,15
5
10
15
20
0,20
0,30
0,30
0,45
WARNING! Fuel and fuel fumes are highly
0,40
0,60
inflammable and can cause serious injury
when inhaled or allowed to come in contact
with the skin. For this reason observe
caution when handling fuel and make sure
there is adequate ventilation.
!
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixing
Fuelling
•
Always mix the petrol and oil in a clean container intended
for fuel.
•
Always start by filling half the amount of the petrol to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of petrol.
WARNING!Taking the following precautions,
will lessen the risk of fire:
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
!
Do not smoke or place hot objects near fuel.
Always shut off the engine before refuelling.
Always stop the engine and let it cool for a
few minutes before refuelling.
When refuelling, open the fuel cap slowly so
that any excess pressure is released gently.
Tighten the fuel cap carefully after refuelling.
Always move the machine away from the
refuelling area before starting.
•
•
Do not mix more than one month’s supply of fuel at a time.
•
•
Always use a fuel container with an anti-spill valve.
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Clean the area around the fuel cap. Contamination in the
tank can cause operating problems.
•
Ensure that the fuel is well mixed by shaking the container
before filling the tank.
WARNING! The catalytic converter muffler
gets very hot during and after use.This also
applies during idling. Be aware of the fire
hazard, especially when working near
flammable substances and/or vapours.
!
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Check before starting
Starting and stopping
•
Check the blade to ensure that no cracks have formed at
the bottom of the teeth or by the centre hole. The most
common reason why cracks are formed is that sharp
corners have been formed at the bottom of the teeth while
sharpening or that the blade has been used with dull
teeth. Discard a blade if cracks are found.
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
and cause personal injury.
!
Always move the machine away from the
refuelling area before starting. Place the
machine on a flat surface. Ensure the cutting
attachment cannot come into contact with
any object.
Make sure no unauthorised persons are in
the working area, otherwise there is a risk of
serious personal injury.The safety distance
is 15 metres.
•
Check that the support flange is not cracked due to fatigue
or due to being tightened too much. Discard the support
flange if it is cracked.
Starting
Primer bulb: Press the air purge repeatedly until fuel begins
to fill the bulb. The bulb need not be completely filled.
•
•
Ensure the locking nut has not lost its captive force. The
nut lock should have a locking force of at least 1.5 Nm.
The tightening torque of the locking nut should be 35-50
Nm.
Check that the blade guard is not damaged or cracked.
Replace the blade guard if it is exposed to impact or is
cracked.
Choke: Set the choke control in the choke position.
•
Check that the trimmer head and trimmer guard are not
damaged or cracked. Replace the trimmer head or
trimmer guard if they have been exposed to impact or are
cracked.
WARNING! When the engine is started with
the choke in either the choke or start throttle
positions the cutting attachment will start to
rotate immediately.
!
Hold the body of the machine on the ground using your left
hand (CAUTION! Not with your foot!). Grip the starter handle,
slowly pull out the cord with your right hand until you feel
some resistance (the starter pawls grip), now quickly and
powerfully pull the cord.Never twist the starter cord around
your hand.
Repeat pulling the cord until the engine starts. When the
engine starts. return choke control to run position and apply
full throttle; the throttle will automatically disengage from the
start setting.
•
•
Never use the machine without a guard nor with a
defective guard.
All covers must be correctly fitted and undamaged before
you start the machine.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
CAUTION! Do not pull the starter cord all the way out and do
not let go of the starter handle when the cord is fully extended.
This can damage the machine.
Stopping
Stop the engine by switching off the ignition.
CAUTION! Do not put any part of your body in marked area.
Contact can result in burns to the skin, or electrical shock if
the spark plug cap has been damaged. Always use gloves.
Do not use a machine with damaged spark plug cap.
CAUTION! The stop switch automatically returns to the start
position. In order to prevent unintentional starting, the spark
plug cap must be removed from the spark plug when
assembling, checking and/or performing maintenance.
Set the throttle to the start position by first pressing the throttle
lockout and the throttle trigger, then pressing the start throttle
button (A). Then release the throttle lockout and the throttle
trigger, followed by the start throttle button. The throttle
function is now activated. To return the engine to idle, press
the throttle lockout and throttle trigger again.
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
7
8
Keep the cutting attachment below waist level.
General working instructions
Switch off the engine before moving to another area. Fit
the transport guard before carrying or transporting the
equipment any distance.
IMPORTANT!
This section describes the basic safety precautions for
working with clearing saws and trimmers.
9
Never put the machine down with the engine running
unless you have it in clear sight.
If you encounter a situation where you are uncertain how to
proceed you should ask an expert. Contact your dealer or
your service workshop.
WARNING! Neither the operator of the
Avoid all usage which you consider to be beyond your
capability.
machine nor anyone else may attempt to
remove the cut material while the engine is
running or the cutting equipment is rotating,
as this can result in serious injury.
!
You must understand the difference between forestry
clearing, grass clearing and grass trimming before use.
Stop the engine and cutting equipment
before you remove material that has wound
around the blade shaft as otherwise there is
a risk of injury.The bevel gear can get hot
during use and may remain so for a while
afterwards.You could get burnt if you touch
it.
Basic safety rules
1
•
Look around you:
To ensure that people, animals or other things cannot
affect your control of the machine.
WARNING! Watch out for thrown objects.
Always wear approved eye protection. Never
lean over the cutting attachment guard.
Stones, rubbish, etc. can be thrown up into
the eyes causing blindness or serious injury.
•
To ensure that people, animals, etc., do not come into
contact with the cutting attachment or loose objects that
are thrown out by the cutting attachment.
!
•
CAUTION! Do not use the machine unless you are able to
call for help in the event of an accident.
Keep unauthorised persons at a distance.
Children, animals, onlookers and helpers
should be kept outside the safety zone of 15
m. Stop the machine immediately if anyone
approaches. Never swing the machine
2
Inspect the working area. Remove all loose objects, such
as stones, broken glass, nails, steel wire, string, etc. that
could be thrown out or become wrapped around the
cutting attachment.
around without first checking behind you to
make sure no-one is within the safety zone.
3
4
Do not use the machine in bad weather, such as dense
fog, heavy rain, strong wind, intense cold, etc. Working in
bad weather is tiring and often brings added risks, such as
icy ground, unpredictable felling direction, etc.
Basic working techniques
Make sure you can move and stand safely.Check the area
around you for possible obstacles (roots, rocks, branches,
ditches, etc.) in case you have to move suddenly. Take
great care when working on sloping ground.
Always slow the engine to idle speed after each working
operation. Long periods at full throttle without any load on the
engine can lead to serious engine damage.
WARNING! Sometimes branches or grass
get caught between the guard and cutting
attachment. Always stop the engine before
cleaning.
!
WARNING! Machines fitted with saw blades
or grass blades can be thrown violently to
the side when the blade comes into contact
!
with a fixed object.This is called blade
thrust. A blade thrust can be violent enough
to cause the machine and/or operator to be
propelled in any direction, and possibly lose
control of the machine. Blade thrust can
occur without warning if the machine snags,
stalls or binds. Blade thrust is more likely to
occur in areas where it is difficult to see the
material being cut.
5
6
Keep a good balance and a firm foothold.
Always hold the machine with both hands. Hold the
machine on the right side of your body.
Avoid cutting with the area of the blade
between the 12 o'clock and 3 o'clock
positions. Because of the speed of rotation
of the blade, blade thrust can occur if you
attempt to cut thick stems with this area of
the blade.
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Clearing
Grass clearing using a grass blade
•
The clearing technique removes all unwanted vegetation.
Keep the trimmer head just above the ground and tilt it.Let
the end of the cord strike the ground around trees, posts,
statues and the like. CAUTION! This technique increases
the wear on the cord.
•
Grass blades and grass cutters must not be used on
woody stems.
•
•
A grass blade is used for all types of tall or coarse grass.
The grass is cut down with a sideways, swinging
movement, where the movement from right-to-left is the
clearing stroke and the movement from left-to-right is the
return stroke. Let the left-hand side of the blade (between
8 and 12 o’clock) do the cutting.
•
•
The cord wears quicker and must be fed forward more
often when working against stones, brick, concrete, metal
fences, etc., than when coming into contact with trees and
wooden fences.
When trimming and clearing you should use less than full
throttle so that the cord lasts longer and to reduce the
wear on the trimmer head.
Cutting
•
•
If the blade is angled to the left when clearing grass, the
grass will collect in a line, which makes it easier to collect,
e.g. by raking.
Try to work rhythmically. Stand firmly with your feet apart.
Move forward after the return stroke and stand firmly
again.
•
The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower. Keep the cord parallel
to the ground when cutting. Avoid pressing the trimmer
head against the ground as this can ruin the lawn and
damage the tool.
•
•
Let the support cup rest lightly against the ground. It is
used to protect the blade from hitting the ground.
Reduce the risk of material wrapping around the blade by
following these instructions:
1
2
Always work at full throttle.
Avoid the previously cut material during the return
stroke.
•
Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting. Constant
contact of this type can cause damage and wear to the
trimmer head.
•
Stop the engine, unclip the harness and place the
machine on the ground before you start to collect the cut
material.
Sweeping
Grass trimming with a trimmer head
•
The fan effect of the rotating cord can be used for quick
and easy clearing up. Hold the cord parallel to and above
the area to be swept and move the tool to and fro.
Trimming
•
Hold the trimmer head just above the ground at an angle.
It is the end of the cord that does the work. Let the cord
work at its own pace. Never press the cord into the area
to be cut.
•
When cutting and sweeping you should use full throttle to
obtain the best results.
•
•
The cord can easily remove grass and weeds up against
walls, fences, trees and borders, however it can also
damage sensitive bark on trees and bushes, and damage
fence posts.
Reduce the risk of damaging plants by shortening the
cord to 10-12 cm and reducing the engine speed.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Basic setting
Carburettor
•
The basic carburettor settings are adjusted during testing
at the factory. The basic setting is richer than the optimal
setting and should be maintained for the first few hours the
machine is in use. The carburettor should then be finely
adjusted. Fine adjustment should be carried out by a
skilled technician.
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions. After the engine has used 8-10 tanks of fuel the
engine will be run-in.To ensure that it continues to run at peak
performance and to minimise harmful exhaust emissions
after the running-in period, ask your dealer/service workshop
(who will have a rev counter at their disposal) to adjust your
carburettor.
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
Rec. idle speed 2700 rpm
!
Recommended max. speed: See theTechnical data section.
and cause personal injury.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
Function
!
•
The carburettor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the carburettor.
The air/fuel mixture is adjustable. Correct adjustment is
essential to get the best performance from the machine.
Fine adjustment
•
When the machine has been ”run-in” the carburettor
should be finely adjusted. The fine adjustment should be
carried out by a qualified person. First adjust the L-jet,
then the idling screw T and then the H-jet.
•
•
Adjusting the carburettor means that the engine is
adapted to local operating conditions, e.g. climate,
altitude, petrol and the type of 2-stroke oil.
Conditions
The carburettor has three adjustment controls:
L = Low speed jet
•
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted. If you adjust
the carburettor when the air filter is dirty it will result in a
leaner mixture when the filter is finally cleaned. This can
lead to serious engine damage.
H = High speed jet
T = Idle adjustment screw
•
•
•
Carefully turn both jets, L and H, so that they are midway
between fully screwed in and fully screwed out.
Do not attempt to adjust the L and H jets beyond either
stop as this could cause damage.
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
CAUTION! If the cutting attachment rotates when the
engine is idling the idle adjustment screw T should be
turned anti-clockwise until the cutting attachment stops.
•
•
The L and H-jets are used to adjust the supply of fuel to
match the rate that air is admitted, which is controlled with
the throttle. If they are screwed clockwise the air/fuel ratio
becomes leaner (less fuel) and if they are turned anti-
clockwise the ratio becomes richer (more fuel). A lean
mixture gives a higher engine speed and a rich mixture
gives a lower engine speed.
Low speed jet L
Try to find the highest idle speed by turning the low speed jet
L clockwise then anti-clockwise.When the highest speed has
been found, turn the low speed jet L 1/4 turn anti-clockwise.
The T-screw regulates the throttle setting at idle speed. If
the T-screw is turned clockwise this gives a higher idle
speed; turning it anti-clockwise gives a lower idle speed.
+ 1/4
L
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION! For optimum adjustment of the carburettor,
contact a qualified dealer/service workshop that has a
revolution counter at their disposal.
Fine adjustment of the idle speedT
Adjust the idle speed using the idle adjustment screw T, if it is
necessary to readjust. First turn the idle adjustment screw T
clockwise until the cutting attachment starts to rotate. Then
turn the screw anticlockwise until the cutting attachment
stops. The idle speed is correctly adjusted when the engine
will run smoothly in every position.The idle speed should also
be well below the speed at which the cutting attachment starts
to rotate.
Correctly adjusted carburettor
When the carburettor is correctly adjusted the machine will
accelerate without hesitation and burble a little at maximum
speed. It is also important that the cutting attachment does
not rotate at idle. If the low speed jet L is set too lean it may
cause starting difficulties and poor acceleration.
If the high speed jet H is set too lean it will result in less power,
less performance, poor acceleration and/or damage to the
engine.
If both the L and H jets are set too rich it will results in
acceleration problems or too low a working speed.
Adjusting the start throttle speed
The correct start throttle speed is set by means of an adjuster
on the rear of the handle next to the cable. Use this screw (4
mm Allen screw) to increase or decrease the start throttle
speed.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
!
High speed jet H
The high speed jet H affects the engine power, speed,
temperature and fuel consumption. If the high speed jet H is
set too lean (screwed in too far) the engine speed will be too
high and cause engine damage. Do not let the engine run at
full speed for more than 10 seconds.
4 mm
Proceed as follows:
1
2
Run the machine at idle.
Press the start throttle lock as described under the
heading Starting and stopping.
3
If the start throttle speed is too low (below 4000 rpm), turn
the adjuster screw A clockwise until the cutting
attachment starts to rotate. Then turn A clockwise a
further 1/2 turn.
Apply full throttle and turn the high speed jet H very slowly
clockwise until the engine slows down. Then turn the high
speed jet H very slowly anticlockwise until the engine starts to
run unevenly. Now turn the high speed jet H slowly clockwise
a little way until the engine runs smoothly.
4
If the start throttle speed is too high, turn the adjuster
screw A anticlockwise until the cutting attachment stops.
Then turn adjuster screw A clockwise a further 1/2 turn.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
Note that the engine should not be under load when you
adjust the high speed jet H.You should therefore remove the
cutting attachment, nut, support flange and drive disc before
adjusting the high speed jet H.
!
The high speed jet H is adjusted correctly when the machine
burbles a little. If the machine races then the setting is too
lean. If the engine produces a lot of smoke and burbles a lot
then the setting is too rich.
H
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Muffler
Cooling system
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether your
machine is fitted with a catalytic converter.
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
4
The muffler is designed to reduce the noise level and to direct
the exhaust gases away from the operator. The exhaust
gases are hot and can contain sparks, which may cause fire
if directed against dry and combustible material.
3
2
1
The cooling system consists of:
1
2
3
4
Air intake on the starter.
Fins on the flywheel.
Cooling fins on the cylinder.
Cylinder cover (directs cold air over the cylinder).
Some mufflers are equipped with a special spark arrestor
mesh. If your machine has this type of muffler, you should
clean the mesh at least once a week.This is best done with a
wire brush.On mufflers without a catalytic converter the mesh
should be cleaned weekly, or replaced if necessary. On
mufflers fitted with a catalytic converter the mesh should be
checked, and if necessary cleaned, monthly. If the mesh is
damaged it should be replaced. If the mesh is frequently
blocked, this can be a sign that the performance of the
catalytic converter is impaired. Contact your dealer to inspect
the muffler. A blocked mesh will cause the machine to
overheat and result in damage to the cylinder and piston.
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
Bevel gear
The bevel gear is filled with the right quantity of grease at the
factory. However, before using the machine you should check
that the bevel gear is filled three-quarters full with grease.Use
HUSQVARNA special grease.
CAUTION! Never use a machine with a defective muffler.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
!
The grease in the bevel gear does not normally need to be
changed except if repairs are carried out.
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Air filter
Spark plug
The air filter must be regularly cleaned to remove dust and dirt
in order to avoid:
The spark plug condition is influenced by:
•
•
Incorrect carburettor adjustment.
•
•
•
•
•
Carburettor malfunctions
Starting problems
An incorrect fuel mixture (too much or incorrect type of
oil).
Loss of engine power
•
A dirty air filter.
Unnecessary wear to engine parts.
Excessive fuel consumption.
These factors cause deposits on the spark plug electrodes,
which may result in operating problems and starting
difficulties.
If the machine is low on power, difficult to start or runs poorly
at idle speed: always check the spark plug first before taking
any further action. If the spark plug is dirty, clean it and check
that the electrode gap is 0.5 mm. The spark plug should be
replaced after about a month in operation or earlier if
necessary.
Clean the filter every 25 hours, or more regularly if conditions
are exceptionally dusty.
Cleaning the air filter
Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water. Ensure that the filter is dry before
refitting it.
CAUTION! Always use the recommended spark plug type!
An air filter that has been in use for a long time cannot be
cleaned completely.The filter must therefore be replaced with
a new one at regular intervals. A damaged air filter must
always be replaced.
Use of the wrong spark plug can damage the piston/cylinder.
If the machine is used in dusty conditions the air filter should
be soaked in oil.See instructions under the heading Oiling the
air filter.
Oiling the air filter
Always use HUSQVARNA filter oil, art. no. 531 00 92-48.The
filter oil contains a solvent to make it spread evenly through
the filter.You should therefore avoid skin contact.
Put the filter in a plastic bag and pour the filter oil over it.
Knead the plastic bag to distribute the oil. Squeeze the
excess oil out of the filter inside the plastic bag and pour off
the excess before fitting the filter to the machine. Never use
common engine oil. This would drain through the filter quite
quickly and collect in the bottom.
Drive shaft
The drive shaft must be greased every three months during
full-time use. Contact your dealer if you are uncertain about
the procedure.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More
extensive work must be carried out by an authorised service workshop.
Daily
maintenance
Weekly
maintenance
Monthly
maintenance
Maintenance
Clean the outside of the machine.
X
Make sure the throttle trigger lock and the throttle function correctly from a
safety point of view.
X
Check that the stop switch works correctly.
Check that the cutting attachment does not rotate at idle.
Clean the air filter. Replace if necessary.
X
X
X
Check that the guard is undamaged and not cracked. Replace the guard if
it has been exposed to impact or is cracked.
X
X
Check that the trimmer head is undamaged and not cracked. Replace the
trimmer head if necessary.
Check that the locking nut of the cutting equipment is tighten correctly.
Check that nuts and screws are tight.
X
X
X
Check that there are no fuel leaks from the engine, tank or fuel lines.
Check the starter and starter cord.
X
X
Check that the vibration damping elements are not damaged.
Clean the outside of the spark plug. Remove it and check the electrode
gap. Adjust the gap to 0.5 mm or replace the spark plug. Check that the
spark plug is fitted with a suppressor.
X
Clean the machines cooling system.
X
X
X
X
Clean or replace the spark arrestor mesh on the muffler (only applies to
mufflers without a catalytic converter).
Clean the outside of the carburettor and the space around it.
Check that the bevel gear is filled three-quarters full with lubricant. Fill if
necessary using special grease.
Check the fuel filter from contamination and the fuel hose from cracks or
other defects. Replace if necessary.
X
X
X
Check all cables and connections.
Check the clutch, clutch springs and the clutch drum for wear. Replace if
necessary by an autorized service workshop.
Replace the spark plug. Check that the spark plug is fitted with a
suppressor.
X
X
Check and clean the spark arrestor mesh on the muffler (only applies to
mufflers fitted with a catalytic converter).
Lubricate the drive shaft with the special grease.
Do this every three months.
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
Technical data
Engine
223R
3
Cylinder displacement, cm
Cylinder bore, mm
Stroke, mm
24,5
32,0
27
Idle speed, rpm
2700
Recommended max. fast idle speed, rpm
Speed of output shaft, rpm
11000-11500
8014
Max. engine output, acc. to ISO 8893, kW/ rpm
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
0,8/9000
No
Yes
Manufacturer/type of ignition system
Spark plug
Walbro MB
NGK BPMR 7A/Champion RCJ 7Y
0,5
Electrode gap, mm
Fuel and lubrication system
Manufacturer/type of carburettor
Fuel tank capacity, litre
Zama C1Q
0,5
Weight
Weight without fuel, cutting attachment and guard, kg
Noise emissions
4,5
(see note 1)
Sound power level, measured dB(A)
109
110
Sound power level, guaranteed L
Noise levels
dB(A)
WA
(see note 2)
Equivalent noise pressure level at the operator’s ear,
measured according to EN/ISO 11806 and ISO 7917,
dB(A), min./max.:
98/99
Vibration levels
Vibration levels at handles, measured according to EN/
2
ISO 11806 and ISO 7916, m/s
At idle, left/right handles, min.:
2,7/2,5
2,7/2,7
5,0/4,6
6,1/5,9
At idle, left/right handles, max.:
At max. speed, left/right handles, min.:
At max. speed, left/right handles, max.:
Note 1: Noise emissions in the environment measured as sound power (L ) in conformity with EC directive 2000/14/EC.
WA
Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various
working conditions with the following time distribution: 1/2 idling and 1/2 max speed.
NOTE! The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting
attachments for the machine. The table indicates the lowest and highest values.
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Approved accessories
Type
Cutting attachment guard, Art. no.
Centre hole in blades/cutters, Ø 25,4 mm
Blade shaft thread M10
Grass 255-4 1" (Ø 255 4-teeth)
503 93 42-02
Grass blade/grass cutter
Plastic blades
Grass 255-8 1" (Ø 250 8-teeth)
503 93 42-02
Tricut Ø 300 mm
Trimmy Fix
Superauto II 1"
S35
503 93 42-02 / 503 97 71-01
503 93 42-02 / 503 97 71-01
503 93 42-02 / 503 97 71-01
503 93 42-02 / 503 97 71-01
503 93 42-02 / 503 97 71-01
Trimmer head
Support cup
T35
Fixed
-
EC-declaration of conformity
(Applies to Europe only)
We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Husqvarna 223R with
serial numbers dating from 2006 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with
the requirements of the COUNCIL’S DIRECTIVE:
- of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
- of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.
- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. Conformity assessment according to Annex V.
For information relating to noise emissions, see the chapter Technical data. The following standards have been applied: EN ISO
12100-2, CISPR 12:2005, EN ISO 11806
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type examination on
behalf of Husqvarna AB. The certificates are numbered: SEC/05/1094, 01/164/048, 01/164/049
Huskvarna January 3, 2006
Bo Andréasson, Development manager
26 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Super Auto II
Super Auto II 1
"
1
2
3
6
4
5
4,0 m
13'
15 cm
~2,0 m
6,5
6
"
'
15 cm
6
8
7
"
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
T35
1
2
3
8,5 m
28'
10 cm
4"
4,3 m
14'
4
5
7
6
8
"Clic"
15 cm
6"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S35
1
2
3
8,5 m
28'
10 cm
4"
4,2 m
14'
4
5
7
6
8
"Clic"
10
11
15 cm
6"
´®z+R9@¶6^¨
´®z+R9@¶6^¨
Download from Www.Somanuals.com. All Manuals Search And Download.
S35
1
2
4,25 m
14'
4,25 m
14'
4
3
5
15 cm
6"
B
A
15 cm
6"
Download from Www.Somanuals.com. All Manuals Search And Download.
1150253-26
´®z+R9@¶6^¨
´®z+R9@¶6^¨
2006-07-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|
