1
530508-3_A
Portable Transducer
Assembling the Metal Bracket
Thank You
Portable Transducer
Assembly
Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by
designing and manufacturing top-quality, thoroughly reliable marine equipment. Genuine Humminbird® accessories
offer the opportunity to upgrade and expand the capabilities of your Humminbird® product.
Phillips-head
Screw
NOTE: Your transducer may not look exactly like the transducer shown in the illustrations, but it will mount in exactly
the same way.
Suction
Cup
Your Humminbird® is designed for trouble-free use in even the harshest marine environment. In the unlikely event
that your Humminbird® does require repairs, we offer an exclusive Service Policy - free of charge during the first year
after purchase, and available at a reasonable rate after the one-year period. For complete details, see the Warranty
section included in this manual.
Wing-Nut
Screw
Contact our Customer Resource Center at either 1-800-633-1468 or visit our website at www.humminbird.com.
Assembling the Plastic Bracket
Installation Overview
Following are instructions for the installation of this accessory. Before you start installation, we encourage you to
read these instructions carefully in order to get the full benefit from your Humminbird® accessory.
Suction Cup
Portable Transducer
Assembly
If you find that any items are missing from your installation kit, call our Customer Resource Center at
Phillips-head
Screw
In addition to the hardware supplied with your transducer, you will need various hand tools.
Wing-Nut
Washer
Installation
Phillips-head
Screw
Lock Washer
Perform the procedures in the following sections to install the transducer on your boat.
NOTE: The suction cup mount is designed for quick, easy installation and removal, NOT for high speed operation. If you
intend to operate your boat at any speed faster than trolling speeds, remove the suction cup transducer from the water.
Assembling the Plastic Bracket
NOTE: Humminbird® portable transducers use either a metal or plastic bracket. The type of transducer that came with
your Humminbird® unit will determine which bracket to use. Refer to the illustration that corresponds with your
transducer and bracket type.
Suction Cup
Portable Transducer
Assembly
It is important that the mounting position allows the transducer to rest beneath the surface of the water, pointing
straight down. You can mount the transducer anywhere on the side of the boat if your boat remains stationary. If you
are trolling, it is best to mount the transducer on the transom of the boat.
Phillips-head
Screw
Lock Washer
Wing-Nut
Washer
Phillips-head
Screw
1.
Testing the Transducer Prior to Installation
Prior to installation, test the transducer to make sure that no damage occurred during shipping.
1. After connecting the transducer to the control head, hold the transducer in the water over the side of the boat to
confirm proper operation. If the transducer is working properly, you should be able to see the bottom on the control
head display.
Assembling the Plastic Bracket
Suction Cup
Portable Transducer
Assembly
2.
Assembling the Mounting Bracket
Phillips-head
Screw
Washer
NOTE: Please be aware that the transducer design has changed. If you are replacing or adding mounting hardware to
your current transducer, make sure that you have selected the appropriate hardware. If you are replacing a transducer,
you will need to replace the mounting bracket and hardware as well. Contact our Customer Resource Center at either
Bolt
Wing-Nut
1. Assemble your transducer mounting bracket using the hardware provided and refer to the illustration that matches your
transducer mounting bracket type.
Ratchet
© 2006 Humminbird®, Eufaula AL, USA.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
530508-3_A
Portable Transducer
Maintenance
All repair work is performed by factory-trained technicians to meet exacting
factory specifications. Factory-serviced units go through the same rigorous
testing and quality control inspections as new production units.
If your boat remains in the water for long periods of time, algae and other
marine growth can reduce the effectiveness of the transducer. Periodically
clean the face of the transducer with hot water. Pivoting the transducer up in
the bracket may allow better access for inspection or cleaning.
After the original warranty period, a standard flat rate service charge will be
assessed for each repair (physical damage and missing parts are not
included). Any repairs made after the original warranty will be warranted for
an additional 90 days after service has been performed by our factory
technicians. You can contact our Customer Resource Center or visit our
website to verify the flat rate repair fee for your product (visit the Product
Support section):
If your boat remains out of the water for a long period of time, it may take
some time to wet the transducer after it is returned to the water. Small air
bubbles can cling to the surface of the transducer and interfere with proper
operation. These bubbles will dissipate with time, or you may wipe the face of
the transducer with your fingers after the transducer is in the water.
1-Year limited Warranty
We warrant the original retail purchaser that products made by Humminbird®
have been manufactured free from defects in materials and workmanship.
This warranty is effective for one year from the date of original retail purchase.
Humminbird® products found to be defective and covered by this warranty will
be replaced or repaired free of charge at Humminbird® option and returned to
the customer freight prepaid. Humminbird® sole responsibility under this
warranty is limited to the repair or replacement of a product that has been
deemed defective by Humminbird®. Humminbird® is not responsible for
charges connected with the removal of such product or reinstallation of
replaced or repaired parts.
We reserve the right to deem any product unserviceable when replacement
parts are no longer available or impossible to obtain. This Service Policy is
valid in the United States only. This applies only to Humminbird® products
returned to our factory in Eufaula, Alabama. This Service Policy is subject to
change without notice.
Returning Your Unit for Service
Before sending your unit in for repair, please contact the factory, either by
phone or by email, to obtain a Repair Authorization Number for your unit.
Please have your product model name and serial number available before
calling the factory. If you contact the factory by e-mail, please include your
product model name and serial number in the e-mail, and use Request for
Repair Authorization Number for your e-mail subject header. You should
include your Repair Authorization Number in all subsequent communications
about your unit.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended in the product
installation and operation instructions;
• Damaged or has failed because of an accident or abnormal operation;
• Repaired or modified by entities other than Humminbird®.
For IN-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird® Customer
Resource Center.
Please retain your original receipt as a proof of the purchase date. This will be
required for in-warranty service.
• Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD® AND WILL BE
THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE
IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN
DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN NO
EVENT WILL HUMMINBIRD® BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY RELATING TO THE PRODUCTS.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date of purchase).
• Return product freight prepaid to Humminbird®, using an insured carrier
with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird® Customer
Resource Center.
Some states do not allow limitations on an implied warranty, or the exclusion
of incidental or consequential damages, so the above exclusions may not
apply to you. You may also have other rights, which vary from state to state.
• Include payment in the form of credit card number and expiration date,
money order or personal check. Please do not send cash.
• Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
Humminbird® Service Policy
Even though you'll probably never need to take advantage of our incredible
service policy, it's good to know that we back our products this confidently.
We do it because you deserve the best. We will make every effort to repair
your unit within three business days from the receipt of your unit at our
factory. This does not include shipping time to and from our factory. Units
received on Friday are typically shipped by the following Wednesday, units
received Monday are typically shipped by Thursday, etc.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird®, using an insured carrier
with delivery confirmation.
© 2006 Humminbird®, Eufaula AL, USA.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
530508-3_A
Portable Transducer
Contact Humminbird®
Contact the Humminbird® Customer Resource Center
in any of the following ways:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
For direct shipping, our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
WARNING! Do not touch an active transducer during operation, as this may
cause physical discomfort and may result in personal injury in the form of tissue
damage. Handle the transducer only when the power to the control head is off.
WARNING! This device should not be used as a navigational aid to prevent
collision, grounding, boat damage, or personal injury. When the boat is moving,
water depth may change too quickly to allow time for you to react. Always
operate the boat at very slow speeds if you suspect shallow water or
submerged objects.
WARNING! Disassembly and repair of this electronic unit should only be
performed by authorized service personnel. Any modification of the serial
number or attempt to repair the original equipment or accessories by
unauthorized individuals will void the warranty. Handling and/or opening this
unit may result in exposure to lead, in the form of solder.
WARNING! This product contains lead, a chemical known to the state of
California to cause cancer, birth defects and other reproductive harm.
© 2006 Humminbird®, Eufaula AL, USA.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|