Portable Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
REQUIRED TOOLS AND MATERIALS:
WARNING!
• Garden Hose or
Sand
• 2 People
• (2 each) Wrenches and/or
Socket Wrenches and
Sockets (Deep-Well Sockets
are Recommended).
• Tape Measure
• Wood Board (scrap)
7/16"
1/2"
9/16"
3/4"
AND/OR
• Sawhorse or
Support Table
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• Step Ladder
8ft. (2.4 m)
• Hammer
7/16"
1/2"
9/16"
3/4"
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
• Tape
• Optional: Large &
Small Adjustable
Wrenches
• Phillips Screwdriver
• Extension is Recommended.
PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632-792
Internet Address: www.huffysports.com
1
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
•
•
If using a ladder during assembly, use extreme caution.
Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
•
Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to seperate during play and/or during transport of the system.
Climate, corrosion or misuse could result in system failure.
If technical assistance is required, contact Huffy Sports.
Minimum operational height is 6'-6" (1.98m) to the bottom of backboard.
•
•
•
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
NOTICE TO ASSEMBLERS
ALL Huffy Sports basketball systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to instructions. Failure to follow instructions could
result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
WARRANTY CARD:
Please remember to complete your product
registration form either on-line at:
www.huffysports.com/warrantycard or mail-in
the enclosed postcard.
3
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST (See Hardware Identifier)
Item Qty. Part No. Description
Item Qty. Part No. Description
204856 Handle, Right
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
4
2
1
7*
1
1
2
20*
1
2
1
1
9*
1
1
1
2
2
6
2
2
4
1
1
2
2*
1
1
1
4
1
900026
908107
908028
200188
202822
200117
203124
203063
906410
202662
203218
203220
200516
203798
203100
203223
226401
200123
200512
203232
206252
206948
203330
900122
900223
203103
226403
206940
206938
206956
904866
Top Pole Section, Black
Middle Pole Section, Black
Bottom Pole Section, Black
Rod, Zinc 3/8 x 5-1/4 Long
Eyebolt, 3/8–16 x 3-3/4 Long
Base
Stake, Tie Down
Lock Nut, Nylon Insert, 3/8–16
Struts, Base
Bolt, 5/16-18 x 4-1/2 Long
Washer, Flat, 5/16 x 7/8 O.D.
Lock Nut, Nylon Insert, 5/16-18
Vinyl, Bolt Cover, 5/16
Bolt, Hex Flange, 5/16-18 x 1-1/2 Long
Lock Nut, Whiz, 5/16-18
Bolt,Carriage 5/16-18 X 1.00” Long
Wheel 4” Diameter
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
1
1
1
1
1
1
1
2
1
2
12
1
2
2
1
3
1
2
6
7
4
4
4
4*
2
1
1
2
8
1
1
1
200118
204872
206219
203814
201568
204832
203053
206990
204859
201219
203038
201129
900846
240017
206360
203493
900183
204847
206340
201682
201611
265601
203309
904807
207103
201139
900867
202862
204837
Front Cover
Label, Height Indicator
Cap, Base-Black
Label, Height and Moving
Anchor Strap
Bracket, Pole Mount
9
Bolt, Carriage, 5/16-18 x 4 Long
Reinforcement Bracket
Cover
Smart Clip, Net Holder
Bolt, Carriage, 5/16-18 x 2.75" Long
Spacer, Metal, .5 O.D. x .402 I.D. x 1.8 Long
Board Bracket
Bolt, Hex Head, 1/4-20 x 2-1/4 Long
Bolt, Hex Head, 3/8-16 x 2.625 Long
Lock Nut, Hex Center-lock, 1/4-20
Elevator Tube, Lower (Long)
Bolt, Hex Head, 1/2-13 x 9-1/2 Long
Lock Nut, 1/2-13
Spacer, Black, .56 I.D. x .683 O.D. x 1.88 Long
Bolt, Hex Flange, 5/16-18 x 3 Long
Bolt, Carriage, 5/16-18 x 3-1/2 Long
Washer, Flat, 1" O.D.
Elevator Tubes, Upper (Short)
Pole Cap
Bolt, Hex Head, 1/2-13 x 4-1/2 Long
Triangle Plate
Spacer, Plastic, 1/2 I.D., 1-1/4 Long
Spring
Net
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Upper Pivot Bracket
Bolt, Hex Head,3/8-16 x 3-1/2 Long
Washer, 3/8 I.D., x 3/4 O.D.
Bolt, Hex Head, 3/8-16 x 1 Long
Lower Pivot Bracket
Bolt, Hex Head, 3\8-16 x 4-1/2 Long
Hinge Tubes
Wheel Bracket
Bolt, Carriage, 5/16-18 x 2 Long
Wheel 6” Diameter
Axle, .461 O.D. x 21 Long
Push Caps
Disc, Plastic, 5” O.D. x .0625 Thick
Height Adjustment Rod
204858 Spacer, Plastic, Biscuit
204857 Spacer, Metal 1/2” O.D. x 1.44 Long
204853 Lanyard, Black Coil
204850 Pin, Locking
204803 Screw, Phillips Head
201124
Rim
35
36
37
38
Lock Nut, Hex, 3/8-16
204855 Handle, Left
NOTE:
*You may have extra parts
with this model
WARRANTY CARD:
Please remember to complete your product
registration form either
on-line at:
or mail-in the enclosed postcard.
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS
DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-
FREE NUMBER FOR FREE REPLACEMENT:
U.S. 1-800-558-5234; CANADA: 1-800-284-8339;
P/N 211574
09/04
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #4 (1)
Item #57 (6)
Item #65 (1)
Item #10 (1)
Item #5 (1)
Item #23 (1)
Item #19 (1)
Item #16 (1)
Item #54 (3)
Item #26 (6)
Item #53 (1)
Item #21 (1)
Item #50 (1)
Item #60 (4)*
Item #61 (4)
Item #14 (2)
Item #46 (2)
Item #36 (1)
HARDWARE IDENTIFIER (CONTINUED)
5
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (NUTS & WASHERS)
Item #37 (3)*
Item #55 (1)
Item #15 (20)*
Item #58 (7)
Item #11 (7)*
Item #8 (4)
Item #20 (8)*
Item #62 (4)*
Item #12 (1)
HARDWARE IDENTIFIER (STEEL SPACERS, RODS & CLIPS)
Item #51 (2)
Item #33 (2)*
HARDWARE IDENTIFIER (PLASTIC SPACERS, CAPS & CLIPS)
Item #13 (1)
Item #67 (8)
Item #59 (4)
Item #49 (12)
Item #32 (2)
Item #29 (4)
*You may have extra parts with this model.
P/N 211574
09/04
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU START!
To ensure optimal playability of backboard system, a close tolerance fit between the elevator
components and hardware is required. Test-fit large bolts into large holes of elevator tubes,
backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out
any excess paint from holes if necessary.
AVANT DE COMMENCER !
Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien
ajustés (serrés). À titre d'essai, insérez les gros boulons dans les gros trous des tubes du système élévateur, des supports
du panneau et des plaques triangulaires. Basculez-les avec précaution en imprimant un mouvement circulaire pour
éliminer l'excédent de peinture, si nécessaire.
¡ANTES DE COMENZAR!
Para asegurar el óptimo rendimiento del sistema del respaldo en el juego, se requiere un ajuste de tolerancia estrecha
entre los componentes del elevador y el herraje. Pruebe el ajuste de los pernos grandes en los orificios grandes de los
tubos elevadores, soportes del respaldo y placas triangulares. Cuidadosamente muévalos en círculos para eliminar
cualquier exceso de pintura, si es necesario.
VORBEREITENDE MASSNAHMEN
Um sicherzustellen, dass das Korbwandsystem optimal für den Spielbetrieb geeignet ist, müssen die Komponenten der
Verlängerungsvorrichtung und die verschiedenen Befestigungsteile fest miteinander verschraubt werden. Große Schrauben
zur Probe in die großen Löcher der Verlängerungsrohre, Korbwandklammern und Dreiecksplatte stecken und diese
vorsichtig in einer Kreisbewegung hin- und herbewegen, um eventuelle Farbrückstände aus den Bohrungen zu entfernen.
7
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDDLE
Identify pole sections.
1.
2
5"
(13 cm)
3
ID Sticker
1
TOP
BOTTOM
5"
(13 cm)
ID Sticker
While maintaining alignment, bounce middle pole section (2) into top section (1)
using a wood scrap as shown until the top pole no longer moves toward the pole
identification sticker on the middle pole.
2.
NOTE:
IMPORTANT!:
Align dimple of top pole section (1)
into trough of middle pole section (2)
as shown.
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM)
MINIMUM OVERLAP.
CAUTION!
m i d d l e p o l e
ID
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-
1/2" BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
STICKER
TROUGH
2
5"
m i d d l e p o l e
1-1/2"
DIMPLE
1
WOOD SCRAP
(NOT SUPPLIED)
HOLE
P/N 211574
09/04
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Bounce top and middle pole assembly (1 & 2) onto bottom pole section (3) using a
wood scrap as shown. Bounce until the top and middle pole assembly no longer
moves toward the pole identification mark on the bottom pole.
3.
NOTE:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM)
IMPORTANT!:
MINIMUM OVERLAP.
Align dimple of middle pole section (2)
into trough of bottom pole section (3)
as shown.
CAUTION!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-
1/2" BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
ID
STICKER
1-1/2"
Bottom pole
TROUGH
5"
1
Bottom pole
DIMPLE
RODS SHOWN ARE
FOR VISUAL
REPRESENTATION
OF ALIGNMENT
AND ARE NOT
HOLE
2
SUPPLIED WITH
THE HARDWARE
3
WOOD SCRAP
(NOT SUPPLIED)
9
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Install wheels (17) onto axle (28) and wheel bracket (25) with push caps (29) as shown.
4.
17
29
25
28
17
29
Position base as shown. Secure wheel bracket assembly with bolt (16) and nut (15) as shown.
5.
15
15
16
P/N 211574
09/04
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Install rod (4) through holes in bottom pole section (3) and eyebolt (5).
Insert pole assembly into tank (6) and through center hole on wheel assembly as shown. Secure
pole assembly with strap (44), washer (11) and lock nut (8).
6.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
4
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
1
2
3
5
4
5
44
11
8
11
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as shown.
7.
3
12
11
WARNING!
11
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
10
13
9
NOTE:
ORIENTATION OF STRUTS
Rotate the non-secured ends of base struts (9)
as shown.
9
9
P/N 211574
09/04
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure base struts (9) to base using bolt (14) washers (11) and nut (15).
8.
14
WARNING!
9
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
11
11
15
Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut (8) as shown.
9.
8
20
18
19
13
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured during step 13.
Carefully place base assembly on its side. Install lower pivot bracket (22) with bolt (23), washers
(20) and lock nut (8) as shown.
10.
IMPORTANT!:
DO NOT OVER
TIGHTEN
21
8
18
20
20
22
23
Secure both hinge tubes (24) to second wheel bracket (25) with carriage bolts (26) and
flange nuts (15).
11.
26
24
25
15
24
IMPORTANT!:
WICHTIG!:
¡IMPORTANTE!:
NOTE ORIENTATION
NOTEZ L'ORIENTATION.
DIE KORREKTE AUSRICHTUNG BEACHTEN.
NOTE LA ORIENTACIÓN.
P/N 211574
09/04
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown.
12.
27
IMPORTANT!:
25
29
28
27
29
SIDE OF WHEEL WITH
LONGER PLASTIC
AXLE NEEDS TO FACE
THE WHEEL BRACKET.
Position base as shown. Secure wheel
bracket assembly with disc (30), washer
(20) and nut (8) as shown.
Carefully reposition entire
assembly as shown:
13.
14.
21
30
20
8
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
IMPORTANT!:
DO NOT OVER
TIGHTEN
15
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Install pole mount bracket (45) and reinforcement bracket (47) with carriage bolts
(46) as shown. Tighten flange nuts (15) completely.
15.
15
45
15
47
46
46
1
Attach spacers (32, 33) to pole mount bracket (45) with bolts (54), washers (20),
and lock nuts (37) as shown. IMPORTANT! Tighten just until washers (20) stop
moving.
16.
45
20
37
20
20
20
32
54
33
33
32
P/N 211574
09/04
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble lanyard (34) to locking pin (35) as shown (FIG A). Attach covers (48) onto
pole mount bracket (45) with carriage bolt (50) and nut (15) as shown.
17.
IMPORTANT!:
48
15
Loop end of pin
lanyard (34) over
carriage bolt (50)
as it passes
through the pole
mount bracket
(45) during this
assembly.
45
48
FIG. A
34
50
50
34
FRONT
SIDE
35
35
Apply logo and height indicator labels (41) to
adjustment rod (31) as shown. Attach handle
parts (38, 39) to adjustment rod with screw
(36), carriage bolts (26), and flange nuts (15)
as shown.
18.
41
31
IMPORTANT!:
41
Indicator labels
should be applied
as close to holes
as possible to
prevent labels from
being damaged
during height
15
adjustment.
39
26
36
15
38
26
17
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert handle assembly through pole mount assembly as
shown. Lock pole assembly in place at the 10’ (3.05 m)
mark with pin (35).
19.
35
Install spacers (51) onto backboard brackets (52), with bolts (53, 54) and lock
nuts (55, 37) as shown.
20.
52
55
37
51
53
54
IMPORTANT!:
KEEP HARDWARE LOOSE
UNTIL AFTER STEP 25 IS
COMPLETED.
P/N 211574
09/04
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Identify elevator tubes (63 & 56).
21.
Toward
Board
Toward
Pole
63
56
Upper Elevator tube
Lower Elevator tube
Toward
Board
Toward
Pole
Attach lower elevator tubes (56) and counter balance spring (68) to backboard
support brackets (52) using spacers (59), bolt (57), and nut (58) as shown.
58
59
52
56
59
68
57
56
19
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting with nuts (15) flush
against bracket (52) secure rim
(70) and bracket to backboard.
15
22.
52
68
15
IMPORTANT! For spring
loaded rim assembly, refer
to instructions included with
rim hardware.
NOTE: Rim mounting nuts
and bolts supplied with rim
hardware.
NOTE: DO NOT use washers
here on spring return style
rims.
62
60
70
Attach upper elevator tubes (63) to backboard support brackets (52) using spacers
(59), bolt (57), and nut (58) as shown.
23.
58
59
52
59
63
57
63
P/N 211574
09/04
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Support pole on sawhorse. Attach backboard assembly to top pole section (1)
as shown. Install pole cap (64). NOTE: Two people are recommended for this
step. Use caution; elevator assembly is heavy.
24.
58
56
67
66
1
58
64
66
65
67
56
57
25. Install upper elevator tubes (63) to triangle plates (66) as shown. Install handle
assembly to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as
shown.
NOTE: Before going on to next step, set adjustable system assembly to the 10’
(3.05 m) setting.
58
58
67
63
51
67
1
67
56
66
WARNING!
56
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
67
57
IMPORTANT!:
TIGHTEN ALL HARDWARE
FROM STEP 20-25 AFTER
THIS ASSEMBLY IS
57
63
COMPLETED.
21
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert bolt (57) through left side upper elevator tube (63), then stretch spring
(68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63)
and secure with nut (58).
26.
WARNING!
USE EYE PROTECTION
WHEN INSTALLING
SPRINGS.
58
63
57
63
68
P/N 211574
09/04
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION D: INSTALL FRONT COVER & HANDLE
Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (42) in place.
27.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
42
8
WARNING!
DO NOT LEAVE
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
OVER.
CAUTION!
ADD TWO GALLONS (7.6
LITERS) OF NON-TOXIC
ANTIFREEZE IN SUB-
FREEZING CLIMATES.
NOTE:
44
IF USING SAND:
2 GALLONS OF
ANTI-FREEZE IS
NOT REQUIRED
Attach front cover (40) to hinge tubes (18) using carriage bolts (51) and flange nuts (22)
as shown.
28.
24
15
40
61
23
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
Roll assembly to desired playing area. Secure assembly
to ground using strap (44) and tie down stake (7).
29.
30.
Apply height and moving label
(43) to front of pole as
shown.
8
HEIGHT ADJUSTMENT
TO ADJUST BACKBOARD:
1. While holding handle, remove pin.
44
2. Move elevator up or down to
desired height.
43
10 feet
(3.05m)
3. Replace pin full length to lock
system at desired height.
7
MOVING SYSTEM
1. Adjust basketball backboard
height to lowest position.
1
2. Rotate handle forward until
wheels engage ground.
3. Move basketball system to
desired location.
4. Rotate handle back to original
position.
2
3
5. Reattach ground restraint and
check system for stability.
4
203814
03/04
ELEVATOR HEIGHT ADJUSTMENT
31
WARNING!
DO NOT ALLOW
CHILDREN TO
ADJUST HEIGHT.
31.
35
A. While holding handle, remove pin (35).
B. Move elevator up or down to desired height.
C. Replace pin (35) full length to lock system at
desired height.
A.
C.
B.
P/N 211574
09/04
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Install net clips.
Installez les pinces du filet. Netzhalteklammern anbringen. Instale los sujetadores de la red.
32
WARNING: Use of this product without proper installation
of net clips, or when all net clips are not present could result in
bodily harm. Be sure to follow directions carefully.
CLIP “ARM”
" BRAS " DE LA
PINCE
AVERTISSEMENT L'utilisation de ce produit sans installer
correctement ou toutes les pinces du filet risque de causer des
blessures. Veillez à suivre scrupuleusement les instructions.
:
CLIP-ARM
WARNUNG: Ein Gebrauch dieses Produkts ohne ordnungsgemäß
angebrachte Netzhalteklammern bzw. ohne den Gebrauch der
Netzhalteklammern kann Verletzungen nach sich ziehen. Die Anleitung
genau befolgen.
"BRAZO" DEL
SUJETADOR
CLIP “BODY”
" CORPS " DE LA PINCE
CLIP-HAUPTTEIL
ADVERTENCIA: Si este producto se usa con los sujetadores de la red
incorrectamente instalados, o si no están todos presentes, se pueden
ocasionar lesiones corporales. Asegúrese de seguir cuidadosamente
las instrucciones.
"CUERPO" DEL
SUJETADOR
70
Insert one “arm” of clip (70) into ram (49) as shown. Twist “body” of clip slightly so that second “arm”
slides over the top of the first “arm” as shown.
Push in direction indicated by arrows.
Insérez un " bras " de la pince (70) dans l'éperon (49), comme illustré. Tournez légèrement le corps de la
pince de sorte que le second bras glisse par-dessus le premier, comme illustré.
Einen Arm des Clips (70) wie gezeigt in die Spirale (49) einsetzen. Den Hauptteil des Clips etwas drehen,
sodass der zweite Arm wie gezeigt oben über den ersten Arm geschoben werden kann.
A
Introduzca un "brazo" del sujetador (70) en el accionador (49) como se muestra. Tuerza ligeramente el
"cuerpo" del sujetador de manera que el segundo "brazo" se deslice sobre el primer "brazo" como se
muestra.
49
Push second “arm” back and into ram as shown.
Poussez dans le sens des flèches.
In die durch die Pfeile angezeigte Richtung schieben.
Empuje hacia la dirección que indican las flechas.
B
Twist “body” of clip slightly again to spread “arms” of clip.
Clip “arms” must be flat and touching edge to edge as shown, not overlapping.
Tournez légèrement le corps de la pince une nouvelle fois pour en étaler les bras.
Den Hauptteil des Clips noch einmal leicht drehen, um die Arme des Clips zu spreizen.
Otra vez tuerza ligeramente el "cuerpo" del sujetador para abrir los "brazos" del
sujetador.
C
25
09/04
P/N 211574
Download from Www.Somanuals.com. All Manuals Search And Download.
70
33.
Install net.
SIDE VIEW
VUE DE CÔTÉ
SEITENANSICHT
VISTA LATERAL
Installez le filet.
Das Netz anbringen
Instale la red.
NETCLIP
PINCE DE FILET
NETZHALTEKLAMMER
SUJETADOR DE LA RED
69
49
NET
FILET
NETZ
RED
Insert net into bottom of clip as shown.
Insérez le filet dans la base de la pince, comme illustré.
Das Netz wie gezeigt unten in den Clip stecken.
Introduzca la red en la parte inferior del sujetador como se muestra.
Twist net until it snaps into position.
Net must be centered through clip.
NETCLIP
PINCE DE FILET
NETZHALTEKLAMMER
SUJETADOR DE LA RED
SIDE VIEW
VUE DE CÔTÉ
SEITENANSICHT
VISTA LATERAL
Tournez le filet jusqu'à ce qu'il s'enclenche en position.
Das Netz drehen, bis es einschnappt.
Tuerza la red hasta que quede conectada en su posición.
Le filet doit être centré dans la pince.
Das Netz muss im Clip zentriert werden.
NET
FILET
NETZ
RED
La red debe quedar centrada a través del sujetador.
P/N 211574
09/04
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|