REQUIRED TOOLS
AND MATERIALS:
Portable System
Owners Manual
• 2 People
• Tape Measure
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
• Wood Board
(scrap)
• Sawhorse or
Support Table
• Tape
• Safety Glasses
• #3 Phillips
Screwdriver
• Needle-Nose Pliers
• (2 each) Wrenches
7/16" 1/2" 9/16" 3/4"
AND/OR
• Socket Wrenches and Sockets
(Deep-Well Sockets are
Recommended).
7/16" 1/2" 9/16" 3/4"
• Garden Hose or Sand
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• Step Ladder 8ft. (2.4 m)
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
OPTIONAL TOOLS
AND MATERIALS:
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
• Large & Small Adjustable
Wrenches
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 7921
Internet Address: http://www.huffysports.com
1
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
HEIGHT ADJUSTMENT
SAFETY INSTRUCTIONS
CAUTION!
DO NOT LET GO OF HANDLE
UNTIL THE RIM IS RESET AT
LOWEST POSTION OR
DESIRED HEIGHT.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND
WILL VOID WARRANTY.
FAILURE TO FOLLOW THIS
READ BEFORE
Owner must ensure that all players know and follow these
rules for safe operation of the system.
WARNING COULD RESULT
OPERATING
IN SERIOUS INJURY AND/OR
ELEVATOR
PROPERTY DAMAGE.
SYSTEM
To ensure safety, do not attempt to assemble this system
without following the instructions carefully. Proper and
complete assembly, use and supervision is essential for
proper operation and to reduce the risk of accident or injury.
A high probability of serious injury exists if this system is not
installed, maintained, and operated properly. Check entire box
and inside all packing material for parts and/or additional
instructional material. Before beginning assembly, read the
instructions and identify parts using the hardware identifier
and parts list in this document.
3.
2.
1.
• If using a ladder during assembly, use extreme
caution.
TO RESET OR REPOSITION BACKBOARD:
• Two (2) capable adults are recommended for this
operation.
1. Grasp handle firmly and pull down to raise rim PAST
highest position (above 10 feet).
• Check base regularly for leakage. Slow leaks could
cause system to tip over unexpectedly.
• Seat the pole sections properly (if applicable). Failure
to do so could allow the pole sections to separate
during play and/or transport of the system.
• Climate, corrosion, or misuse could result in system
failure.
2. While still holding handle firmly, CAREFULLY lower
rim to lowest position.
3. Raise to desired height by pulling down on handle.
1. Adjust basketball
backboard height to
lowest position.
MOVING
SYSTEM
• Minimum operational height is 6' 6" (1.98 m) to the
bottom of backboard.
2. While holding pole,
• This equipment is intended for home recreational use
only and NOT excessive competitive play.
• Read and understand the warning label affixed to
pole.
rotate basketball
system forward until
wheels engage with
ground.
• The life of your basketball pole depends on many
conditions. The climate, placement of the pole,
location of the pole, exposure to corrosives such as
pesticides, herbicides, or salts are all important.
3. Move basketball
system to desired
location.
4. Carefully rotate
basketball system
upright.
•
If technical assistance is required, contact Customer
Service.
• Adult supervision is recommended when adjusting
height.
5. Check system for
stability.
522730 06/05
Most injuries are caused by misuse and/or not following
instructions.
25
Use caution when using this system.
3
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE TO ASSEMBLERS
Adult Assembly Required. Dispose of ALL packaging materials promptly. As with all products,
periodically inspect for loose small parts.
ALL basketball systems, including those used for DISPLAYS, MUST be assembled and installed
according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is
NOT acceptable to devise a makeshift support system.
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED
IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE
NUMBER:
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
PRODUCT REGISTRATION:
Please remember to complete your product registration form on-
line at:
4
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system...
FRONT VIEW
BACK VIEW
BACKBOARD
BACKBOARD
RIM
RIM
POLE
POLE
ELEVATOR ADJUSTMENT
SUPPORT STRUT
SUPPORT STRUT
BASE
BASE
5
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - See Hardware Identifier
Item Qty. Part No. Description
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
9
1
1
2
1
1
1
1
1
6
2
1
206657 Tank, (Black)
200628 Wheel Axle
25
26
1
1
522730 Label, Height Adjustment and Moving
Net
201160 Pawl Lever
801159 Ratchet
900964 Backboard Bracket
226401 Wheel, 4” (Black)
908242 Top Pole Section
908246 Middle Pole Section
908247 Bottom Pole Section
202820 Rod, 3/8 O.D. x 4-3/4 Long
202822 Eyebolt, 3/8-16 x 2-1/2 Long
203063 Lock Nut, 3/8-16
906206 Tank Strut
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
1
1
2
1
1
1
4
1
1*
1
1
7
1
1
4
7
4
1*
1
1
1
1
203472 Spring, Black, Slam Jam
200318 Bracket, Reinforcement, Slam Jam
900033 Bracket Slam Jam
202587 Spacer .520 I.D. x .750 O.D. x 1.0 Long
206305 Clevis Pin 1/4 x 2-3/8 Long
206360 Bolt, Hex 3/8-16 x 2.65 Long
203796 T-Bolt, 3/8-16 x 5 Long
203470 Washer Flat, Slam Jam
206340 Lock Nut 1/2-13
203795 Nut, Special, Slam Jam
201125 Spring, Ratchet Return
206311 Spacer .520 I.D. x .750 O.D. x .50 Long
206304 Bolt 1/2-13 x 6-5/16 Long
908178 Elevator Tubes
201129 Spacer .402 I.D. x .500 O.D. x 1.8 Long
201642 Spacer Plastic, .63 Long
281159 Handle
10
11
201625 Bolt,Yellow Dichromate, 5/16-18 X 3.60
Long
12
13
14
15
16
17
18
19
20
21
22
23
24
6
1
4
6
6*
4
2
1
2
1
1
1
2
203218 Washer, Flat, 5/16
203099 Lock Nut, 5/16-18
204961 Bolt, Hex Head, 3/8-16 x 0.625 Long
205528 Bolt, Hex Flange, 5/16-18 x 1 Long
203100 Nut, Hex Flange, 5/16-18
201651 Spacer .500 I.D. x .25 Long
206303 Washer 1/4 Flat
200627 Wheel Bracket
204558 Screw, Phillips, 1/4 x .375 Long, Type 25
Rim
206219 Cap, Pole Top 3”
202603 Washer, Nylon
203617 Plug Cap
908176 Tube, Handle, Outer
908177 Tube, Handle, Inner
* You many have extra parts with this model.
NOTE: Hardware kit is designed for more than one style of basketball system.
Not all hardware will be used.
6
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & PINS)
Item #14 (4)
Item #15 (6)
Item #8 (1)
Item #35 (1*)
Item #20 (2)
Item #11 (1)
Item #34 (1)
Item #42 (7)
Item #36 (1)
HARDWARE IDENTIFIER (NUTS & WASHERS)
Item #13 (1)
Item #9 (1)
Item #16 (6*)
Item #38 (7)
Item #18 (2)
Item #39 (1)
Item #12 (6)
Item #23 (1)
Item #37 (1)
* You may have extra parts with this model.
7
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (STEEL SPACERS & RODS)
Item #7 (1)
Item #44 (1*)
HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS)
Item #33 (4)
Item #41 (4)
Item #45 (1)
Item #17 (4)
HARDWARE IDENTIFIER (OTHER)
Item #40 (1)
Item #31 (1)
Item #30 (1)
Item #32 (1)
8
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION A: ASSEMBLE THE BASE
ITEMS REQUIRED FOR THIS SECTION
This is what your system will look like when
you’ve finished this section.
(2) 1/2” and (2) 9/16" Wrenches
AND/OR
(2) Socket Wrenches and Sockets
1/2”
9/16”
Tape
Correctly identify each pole section and mark indicated distance from ends with
tape as shown.
1.
TOP POLE 31”
4
5
MIDDLE POLE 43”
6
BOTTOM POLE 43”
9
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood
scrap as shown until the top pole no longer moves toward the pole identification sticker on the
middle pole.
2.
CAUTION!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-1/2"
BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
IMPORTANT!
Align dimple of top pole section (4)
into trough of middle pole section (5)
as shown.
m i d d l e p o l e
ID
STICKER
5
5"
m i d d l e p o l e
1-1/2"
DIMPLE
4
WOOD SCRAP
(NOT SUPPLIED)
HOLE
10
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap
as shown. Bounce until the top and middle pole assembly no longer moves toward the pole
identification mark on the bottom pole.
3.
IMPORTANT!
Align dimple of middle pole section (5)
into trough of bottom pole section (6)
as shown.
CAUTION!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-1/2"
BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
1-1/2"
Bottom pole
5"
ID
STICKER
4
Bottom pole
DIMPLE
RODS SHOWN ARE
FOR VISUAL
REPRESENTATION
OF ALIGNMENT
AND ARE NOT
HOLE
5
SUPPLIED WITH
THE HARDWARE
6
WOOD SCRAP
(NOT SUPPLIED)
11
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Install rod (7) through holes in bottom pole section (6) and
eyebolt (8).
4.
5.
7
8
Install wheel axle (2) through wheel carriage (19) and
install wheels (3) onto wheel axle (2) with spacers (17) as
shown. Insert pole assembly into tank assembly as
shown. Secure bottom pole (6) section to tank and wheel
carriage as shown. A deep socket is recommended.
WARNING!
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING
COULD RESULT IN SERIOUS
INJURY AND/OR PROPERTY
DAMAGE.
IMPORTANT!
19
3
17
17
3
2
THE SPACER (17) WILL
FIT LOOSELY UNTIL
SECURED INTO THE
CAVITY OF THE BASE.
6
7
8
IMPORTANT!
The Warning Label
should be facing
towards the front.
9
IMPORTANT!
DO NOT OVER
TIGHTEN
12
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure base struts (10) to pole using bolt (11), washers (12), and nut (13), as
shown. Rotate the non-secured ends of base struts (10) as shown.
6.
12
12
13
6
11
10
6
10
1
10
7.
WARNING!
Secure both base struts (10)
to base using bolts (15),
TIGHTEN BOLT (11) IN LOCK NUT (13) UNTIL FLUSH
(EVEN) WITH LOCK NUT’S OUTER EDGE.
washers (12), and nuts (16).
10
15
NOTE:
ORIENTATION OF STRUTS
12
10
15
12
12
1
16
12
16
13
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION B: ATTACH THE BACKBOARD
ITEMS REQUIRED FOR THIS SECTION
This is what your system will
look like when you’ve
finished this section.
(2) 1/2”, (2) 9/16” and (2) 3/4” Wrenches
AND/OR
(2) Socket Wrenches and Sockets
3/4”
1/2”
9/16”
Assemble backboard brackets (29) using bolts (14) and
nuts (9) as shown.
1.
9
9
IMPORTANT!
DO NOT TIGHTEN
COMPLETELY
14
29
NOTE
ORIENTATION.
29
14
Identify elevator tubes (43).
2.
43
Toward
Board
Toward
Pole
Elevator tube
14
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Fit spacer (44) into pawl (27). Then secure to brackets (29) using bolt (35) and nut (52) as shown.
3.
IMPORTANT!
DO NOT OVER TIGHTEN!
29
It is necessary for all
parts to be installed
properly for this
9
mechanism to work
safely and properly.
35
27
44
Attach lower elevator tubes (43) to backboard brackets (29)
using spacers (17, 23, 41, and 45), bolts (42) ratchet (28),
and nuts (38) as shown.
45
4.
23
28
29
17
27
23
45
17
43
38
41
38
17
41
TOP VIEW OF
RATCHET
28
42
ASSEMBLY
17
IMPORTANT!
TIGHTEN ALL
COMPONENTS
42
COMPLETELY (STEP 1-4)
43
15
01/06 ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure pawl (27) in place with clevis
pin (34) and washers (18) as shown.
Stretch spring (40) into position with pliers from
clevis pin (34) to board bracket (29).
5.
6.
WARNING!
34
USE EYE PROTECTION
WHEN INSTALLING
SPRINGS.
18
27
27
43
18
40
43
Insert T-bolt (36) through Slam Jam bracket (32) as shown. Secure
Slam Jam bracket (32) and backboard bracket (29) assemblies to
backboard. Using bolt (15) and nut (16) as shown.
7.
43
16
16
29
36
32
15
15
16
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (43) to backboard brackets (29) using spacers (41) bolt (42) and
nut (38) as shown.
8.
43
43
41
38
42
41
Support pole on sawhorse. Attach upper and lower elevator tubes (43) to upper pole section (4)
using bolts (42) and nuts (38) as shown. Attach pole cap (22) as shown.
9.
38
38
43
4
22
43
42
42
17
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach outer handle tube (47) to upper elevator tubes (43) using bolt (42) spacers (33) and
nut (38) as shown.
10.
A
42
33
47
43
33
38
Attach outer handle tube (47) to lower elevator tubes (43) using bolt (42) spacers (33) and
nut (38) as shown.
10.
B
42
33
43
33
43
47
43
38
18
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Slide inner handle tube (48) into outer handle tube (47) as shown.
11.
47
48
Secure inner handle tube (48) to outer handle tube (47) using screws (20) as shown.
Slide handle (46) onto inner handle tube (48).
12.
20
47
48
46
20
19
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Rim to Backboard
A. Fit rim (21) securely into bracket (32) as shown. Allow T-bolt (36) to slip through center hole
13.
in rim (21).
B. Install reinforcement bracket (31) onto T-bolt (36) as shown.
C. Install spring (30) onto T-bolt (36) as shown.
D. Install special nut (39) and washer (37) onto T-bolt (36).
E. Tighten special nut (39) until flush with end of T-bolt (36).
B
NOTE:
A
31
ORIENTATION
OF BRACKET
21
36
36
32
31
37
39
C
D
30
36
37
36
39
E
20
ID# M732201 01/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Roll the completed assembly to the desired playing area. Fill tank with 33 gallons of water.
14.
WARNING!
TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING
COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
DO NOT LEAVE
ASSEMBLY
24
UNATTENDED WHEN
EMPTY; IT MAY TIP
OVER.
24
NOTE:
IF USING SAND:
2 GALLONS OF
ANTI-FREEZE IS
NOT REQUIRED
Apply the height adjustment and moving label (25) to the front of the pole as shown.
15.
WARNING!
DO NOT ALLOW
CHILDREN TO
HEIGHT ADJUSTMENT
ADJUST HEIGHT.
TO RESET OR
REPOSITION
BACKBOARD:
HEIGHT ADJUSTMENT
CAUTION!
DO NOT LET GO OF HANDLE
UNTIL THE RIM IS RESET AT
LOWEST POSTION OR
DESIRED HEIGHT.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
READ BEFORE
OPERATING
ELEVATOR
SYSTEM
1. Grasp handle firmly and
pull down to raise rim
PAST highest position
(above 10 feet).
1.
2.
3.
25
TO RESET OR REPOSITION BACKBOARD:
1. Grasp handle firmly and pull down to raise rim PAST
highest position (above 10 feet).
2. While still holding handle firmly, CAREFULLY lower
rim to lowest position.
3. Raise to desired height by pulling down on handle.
10 ft.
1. Adjust basketball
backboard height to
lowest position.
MOVING
SYSTEM
(3.05 m)
2. While holding pole,
rotate basketball
system forward until
wheels engage with
ground.
2. While still holding handle
firmly, CAREFULLY lower
rim to lowest position.
3. Move basketball
system to desired
location.
4. Carefully rotate
basketball system
upright.
5. Check system for
stability.
522730 06/05
3. Raise to desired height
by pulling down on
handle.
21
01/06
ID# M732201
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Fitness Equipment 3A2096D User Manual
Grindmaster Coffeemaker B 3 User Manual
Grundig Stereo System CDC 477 User Manual
Hamilton Beach Oven 31116Y User Manual
HANNspree Flat Panel Television DT06 10C1 User Manual
Harbor Freight Tools Drill 40209 User Manual
Harbor Freight Tools Sander 43477 User Manual
Hasbro Motorized Toy Car 23732 User Manual
Hotpoint Washer HVL 241 User Manual
HP Hewlett Packard Network Card AD465A User Manual