Owner’s Manual
for
Multi-Speed Comfort Bicycles
This manual contains important safety, assembly,
operation and maintenance information.
Please read and fully understand this
manual before operation.
Save this manual for future reference.
HComfort EN 071913 m0073
Copyright Huffy Corporation 2013
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Bicycle Identification Record
NOTE: This information is only available on the bicycle itself. It is not available from
Huffy.
Each Huffy bicycle has a Serial Number
stamped into the frame. The Serial
Number (1) can be found on the bottom
of the crank housing as shown.
1
Write this number below to keep it for future reference.
If the bicycle is stolen, give this number and a description of the bicycle to the police.
This will help them find the bicycle.
Model / Serial Number:
Purchase Date:
Model Name:
Fitting the Rider to the Bicycle
1
3
2
To determine the correct size of bicycle for the rider:
• Straddle the assembled bicycle with feet shoulder width apart and flat on the
ground.
• There must be at least 1 inch (2.5 cm) of clearance (1) between the highest part
of the top tube (2) and the crotch of the rider with tires properly inflated.
• The minimum leg-length for the rider is the highest part of the top tube plus one
inch (3).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety Information
Meanings of Warnings:
a
This symbol is important. See the word “CAUTION” or “WARNING” which
follows it.
The word “CAUTION” is before mechanical instructions. If you do not obey these
instructions, mechanical damage or failure of a part of the bicycle can occur.
The word “WARNING” is before personal safety instructions. If you do not obey
these instructions, injury to the rider or to others can occur.
• Do not add a motor to the product.
• Do not tow or push the product.
• Do not modify the product.
• Replace worn or broken parts immediately.
• If anything does not operate properly, discontinue use.
Reflectors
WARNING: For your own safety, do not ride the bicycle if the reflectors are
incorrectly installed, damaged, or missing. Make sure the front and rear reflectors are
vertical. Do not allow the visibility of the reflectors to be blocked by clothing or other
articles. Dirty reflectors do not work well. Clean the reflectors, as necessary, with
soap and a damp cloth.
Rules of the Road
WARNING: Failure of the rider to obey the following “Rules of the Road” can
result in injury to the rider or to others.
• Obey all traffic regulations, signs, and signals.
• Always wear a bicycle helmet that meets safety standards, as well as local safety
standards.
• Ride on the correct side of the road, in a single file, and in a straight line.
• If possible, avoid riding at night, dusk, dawn and any other time of poor visibility.
• If you must ride at night or at time of poor visibility:
• Purchase, install, and use a headlight and taillight.
• Headlights are required by all states for nighttime riding and taillights are re-
quired in some states.
• Battery-powered lights or flashing safety lights are also recommended.
• Make sure the reflectors of your bicycle are correctly positioned. Do not remove
the reflector or replace the reflectors with lighted devices that look similar to
reflectors.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Rules of the Road - continued
• Make yourself more visible to motorists:
• Wear light-colored or reflective clothing, such as a reflective vest and reflec-
tive bands for your arms and legs.
• Use reflective tape on your helmet.
• Do not let anything cover the reflectors.
• Use extra caution in wet weather:
• Ride slowly on damp surfaces because the tires will slide more easily.
• Avoid these hazards to prevent loss of control or damage to your wheels:
• Be aware of drain grates, soft road edges, gravel or sand, pot holes or ruts, wet
leaves, or uneven paving.
• Cross railroad tracks at a right angle to prevent the loss of control.
• Avoid unsafe actions while riding.
• Do not carry any passengers.
• Do not carry any items or attach anything to your bicycle that could hinder your
vision, hearing, or control.
• Do not ride with both hands off the handlebar.
• Do not add a motor to the product.
• Do not tow or push the product.
• Do not modify the product.
• Replace worn or broken parts immediately.
• If anything does not operate properly, discontinue use.
The Owner’s Responsibility
WARNING: This bicycle is made to be ridden by one rider at a time for general
transportation and recreational use. It is not made to withstand the abuse of stunting
and jumping.
If the bicycle was purchased unassembled, it is the owner’s responsibility to follow
all assembly and adjustment instructions exactly as written in this manual, and any
“Special Instructions” supplied and to make sure all fasteners and components are
securely tightened.
NOTE: Periodically check that all fasteners and components are securely tightened.
If the bicycle was purchased assembled, it is the owner’s responsibility, before riding
the bicycle for the first time, to make sure the bicycle has been assembled and ad-
justed exactly as written in this manual, and any “Special Instructions” supplied and
to make sure all fasteners and components are securely tightened.
NOTE:
If product is assembled, please proceed to pages 16 and 19: Testing Stem,
Handlebar and Seat Clamp tightness.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Assembly View
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Assembly List
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This Owner’s Manual is made for several different bicycles:
• Some illustrations may vary slightly from the actual product.
• Follow instructions completely.
• If the bicycle has any parts that are not described in this manual, look for separate
“Special Instructions” that are supplied with the bicycle.
• Models may have different accessory items such as bags, baskets, reflectors, cup
holders, racks, etc.
• All features, components and accessories are not included on all models.
• Use the Index page to locate specific sections of this manual.
• Please read through this entire manual before beginning assembly or maintenance.
WARNING: Keep small parts away from children during assembly.
NOTE: All of the directions (right, left, front, rear, etc.) in this manual are as seen by
the rider while seated on the bicycle.
Do not dispose of the carton and packaging until you complete the assembly of the
bicycle. This can prevent accidentally discarding parts of the bicycle.
Tools Needed
Small Adjustable Wrench
(Jaws must open at least 9/16 inch.)
Open-end Wrenches
Phillips Screwdriver
Metric Allen Wrenches
Flat-blade Screwdriver
Slip-Joint Pliers
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Fender Install (various models)
Loosen the Front Brakes:
1. Squeeze the two Brake arms together
(A).
B
2. Lift out the Brake Cable Guide (B) from
the Guide Bracket (C).
C
A
A
C
B
Note: Turn Fork so that Brake Arms are toward front of bike.
Use Screw Driver and Wrench:
1. Front fender attaching hardware has
been pre-assembled onto the fork. Re-
8
9
move the Bolt (8) and Washer (9) and
Nut (10) from the fork crown.
2. Remove lower mounting Bolts (7) and
Washers (6) from the dropout before
starting (fig 01).
10
6
7
fig 01
continued >>
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Fender Install (various models) - continued
3. Place the Fender (3) in the fork with the
longer fork mounting tab (A) on the rear
side of the fork (fig 02).
4. Insert the Bolt (8) through the Washer
(9) and Fender tabs and fork mounting
9
hole.
8
10
5. Install Washer (9) and Nut (10) onto Bolt
(8) and tighten securely.
9
A
3
fig 01
fig 02
6. Line up the lower Fender Braces (B) with
the Fork Mounting Tabs (C) (fig 03).
7. Insert each lower mounting Bolt (7) and
Washer (6) into the Fork Mounting Tabs
(C) and tighten securely.
7
C
B
6
fig 03
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble the Front Wheel to the Fork
1. If the Axle Nuts (5) are already attached to the front wheel axle, begin by remov-
ing them with an open end wrench or adjustable wrench.
2. Set the wheel into the front fork (21) (fig 04).
3. Install wheel retainers (4) making sure the tabs are in the fork (D) tab holes.
4. Attach the front wheel with the Axle Nuts (5).
5. Tighten Axle Nuts to 21 ft-lbs.
D
21
4
5
4
5
fig 04
Note: Ensure wheel spins freely without contacting fork or fender.
WARNING: Do not use Nuts (5) without serrations to attach the front wheel.
WARNING: Put the wheel in the center of the fork and tighten
both nuts to the recommended torque of 21 ft.-lbs.
WARNING: Failure to obey these steps can allow the front wheel to loosen
while riding. This can cause injury to the rider or to others.
continued >>
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Wheel Install - Notes and Warnings:
NOTE: Ensure wheel spins freely without contacting fork or fender.
WARNING: Do not use Nuts (5) without serrations to attach the front wheel.
WARNING: Failure to obey these steps can allow the front wheel to loosen
while riding. This can cause injury to the rider or to others.
Re-attach Front Brake Cable:
B
Re-attach Front Brake Cable:
1. Squeeze the two Brake arms together
(A).
2. Insert the Brake Cable Guide (B) into
the cutout in the Guide Bracket (C).
3. Make sure the Brake Cable Guide
(B) is seated securely in the Guide
Bracket (C) cutout.
C
A
A
WARNING:
Check Front Brake Adjustment Before
Riding!
See Brakes Section Page 24
C
B
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Fender Install (various models)
Note: Top Fender mount is loose (fig 06) to allow installation.
1. Line up the Rear Fender Braces (A) with the Frame Mounting Tabs (B) (fig 05).
2. Insert each lower mounting Bolt (7) and Washer (6) into the Frame Mounting
Tabs (B) and tighten securely. Make sure fender is centered over tire.
B
A
B
6
7
fig 05
Tighten Top Fender Mount:
3. Tighten Bolt (11) and Nut (10) securely. Make sure fender is centered over tire
(fig 06).
10
11
fig 06
Note: Ensure wheel spins freely without contacting frame or fender.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Handlebar and Stem Instal
WARNING: To prevent steering system damage and possible loss of control,
the “MIN-IN” (minimum insertion) mark (A) on the stem must be below the top of the
Locknut (B).
NOTE: Remove plastic Cap (E) from the
end of the Stem (13).
1. Insert the Stem (13) into the fork (fig
C
07).
2. Point the Stem (13) towards the front of
the bike.
3. Tighten the Stem Bolt (C) just enough to
hold it in position.
4. If necessary, loosen the Handlebar
13
Clamp Nut (D) and rotate Handlebar
(12) into a comfortable riding position
(fig 08).
A
E
5. Tighten Handlebar Clamp Nut (D) just
enough to hold it in position (fig 08).
6. Align the stem (13) with the front tire
and tighten the stem bolt (C) securely
(fig 07).
B
B
A
WARNING: Do not over tighten the
stem bolt. Over tightening the stem bolt can
damage the steering system and cause loss
of control.
fig 07
One Bolt Stem (various models):
• If necessary, re-adjust Handlebar (12) (fig
12
08).
• Tighten Clamp Nut (D).
NOTE: Do not over tighten. Torque to 17
ft-lbs.
D
WARNING: If the handlebar clamp
in not tight enough, the handlebar can slip
in the stem. This can cause damage to the
handlebar or stem, and can cause loss of
control.
fig 08
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Handlebar and Stem Install - continued
Two Bolt Stem (various models):
• If necessary, re-adjust Handlebar (12) (fig
08a).
• Tighten Clamp Screws (D).
12
D
NOTE: Do not over tighten. Torque to 17
ft-lbs.
WARNING: If the handlebar clamp
in not tight enough, the handlebar can slip
in the stem. This can cause damage to the
handlebar or stem, and can cause loss of
control.
fig 08a
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing Stem and Handlebar Tightness
To test the tightness of the stem:
• Straddle the front wheel between your legs.
• Try to turn the front wheel by turning the handlebar.
• If the handlebar and stem turn without turning the front wheel, realign the stem with
the wheel and tighten the stem bolt(s) tighter than before (about 1/2 revolution only
at a time).
• Do this test again, until the handlebar and stem do not turn without turning the front
wheel.
To test the tightness of the handlebar clamp:
• Hold the bicycle stationary and try to move the
ends of the handlebar up and down.
CAUTION: Do not exceed 100 lbs downward
force.
• If the handlebar moves, loosen the bolt(s) of the handlebar clamp.
• Put the handlebar in the correct position and tighten the bolt(s) of the handlebar
clamp tighter than before.
• If the handlebar clamp has more than one bolt, tighten the bolts equally.
• Do this test again, until the handlebar does not move in the handlebar clamp.
Note: Exceeding 100 lbs downward force may damage the Threads of the Stem and
Handlebar. If the Threads are damaged, the Handlebar will not stay in position when
tightened.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Seat Installation
Attach Seat to Seat Post (fig 09):
(pre-assembled on some models)
• Loosen nuts on Seat Clamp (A) and
rotate Seat (14) into riding position.
• Put the Seat Post (33) fully through
the Seat Clamp.
• Tighten the Seat Clamp so the Seat
stays on the seat post.
14
• If the Seat Clamp has a nut on each
side, tighten both nuts equally.
A
33
fig 09
CAUTION: If you accidentally drop the seat post into the seat tube, it may be
difficult to remove it.
• Point the Seat forward and put the
Seat Post into the Seat Tube (B)
(figs 10, 11).
C
14
B
WARNING: To prevent the seat
coming loose and possible loss of
control, the “MIN-IN” (minimum inser-
tion) mark (C) on the seat post must
be below the top of the Seat Tube.
33
B
C
fig 10
continued >>
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Tightening Seat Quick Release Lever
Move the Quick Release Lever (D) to
the “open” position so the word “open”
is pointing away from the Seat Post
Clamp (E).
33
B
F
E
NOTE: The words “open” and “close”
are on opposite sides of the quick
release lever.
D
fig 11
CAUTION: Operate the Quick Release Lever by hand only. Do not use a ham-
mer or any other tool to tighten the quick release lever.
You must use strong force to move the quick release lever to the “close” position. If
you can easily move the lever to the “close” position, the clamping force is too light.
WARNING: If the clamping force of the Quick Release Lever is too light, the
seat post can loosen while riding. This can cause injury to the rider or to others.
Tighten the quick release lever (continued):
• Open and close the Quick Release Lever with one hand while you turn the Adjust-
ing Nut (F) with the other hand (fig 11).
• Tighten or loosen the adjusting nut by hand, so that you first feel resistance to the
quick release lever when it perpendicular to the bicycle frame.
• Push the Quick Release Lever to the “close” position (fig 11).
• When in the “close” position, make sure the Quick Release Lever lays against the
Seat Post Clamp (E).
• The tightening torque of the Quick Release Lever should be tight enough so that
the seat does not move during normal operation.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing Seat Clamp and Post Clamp Tightness
To test the tightness of the seat clamp and the post clamp:
WARNING: Every time the quick release mechanism is loosened, make sure
the red reflector is correctly positioned as shown in fig. 13 next page.
•
Try to turn the seat side-to-side and to move the front of the seat up and down.
•
If the Seat (14) moves in the Seat Clamp (fig 10a):
•
•
Loosen the Seat Clamp (A).
Put the seat in the correct position and tighten the Seat Clamp tighter than
before.
•
Do this test again, until the seat does not move in the Seat Clamp.
•
If the Seat Post (33) moves in the Seat Tube (B):
•
•
Move the Quick Release Lever (C) to the “open” position.
Put the seat in the correct position and tighten the Quick Release Lever
tighter than before.
•
•
If necessary, loosen Quick Release Lever , tighten Adjusting Nut (D) and re-
tighten Quick Release Lever .
Do this test again, until the seat post does not move in the seat tube.
14
33
A
C
D
B
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Front / Rear Reflectors Installation (various models)
Front Reflector Install:
1. Position Reflector (17) so it is near
the Stem (A) and points straight
forward (fig 12).
2. Tighten Clamp Screw.
NOTE: Do not over-tighten. This will
damage the Clamp.
Make sure Reflector view is not ob-
17
A
structed.
fig 12
Rear Reflector Install (various mod-
els):
1. Position Reflector (18) so it points
straight backwards and is not above
the seat post limit (A) (fig 13).
2. Tighten Clamp Screw.
A
NOTE: Do not over-tighten. This will
damage the Clamp.
Make sure Reflector view is not ob-
structed.
18
fig 13
Dual Rear Reflectors (various models):
The Rear Reflectors (40) are pre-installed
on the bike. Make sure they are secure,
not bent and are pointing straight back-
wards.
40
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Pedal Installation
CAUTION: The right pedal is marked “R” and the left pedal is marked “L”.
• The pedal marked “R” has right-hand threads. Tighten it in a clockwise direction.
• The pedal marked “L” has left-hand threads. Tighten it in a counterclockwise
direction (anti-clockwise).
• Turn the right pedal marked “R” into the right side of the crank arm, and the left
pedal marked “L” into the left side of the crank arm.
Tighten the pedals (fig 14):
• Make sure the threads of each pedal are fully into the crank arm.
NOTE: The recommended torque (tightness) for each pedal is 30 ft.-lbs.
L
WARNING: Ensure pedals
are secure in crank arms so they will
not loosen. Periodically check tight-
ness.
R
fig 14
Note: A Pedal Wrench is preferred for attaching Pedals. An open-end
wrench can also be used as shown.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair, Service and Adjustment
WARNING:
• Inspect the bicycle frequently. Failure to inspect the bicycle and to make repairs
or adjustments, as necessary, can result in injury to the rider or to others. Make
sure all parts are correctly assembled and adjusted as written in this manual and
any “Special Instructions”.
• Immediately replace any damaged, missing, or badly worn parts.
• Make sure all fasteners are correctly tightened as written in this manual and
any “Special Instructions”. Parts that are not tight enough can be lost or oper-
ate poorly. Over tightened parts can be damaged. Make sure any replacement
fasteners are the correct size and type.
NOTE: Have a bicycle service shop make any repairs or adjustments for which you
do not have the correct tools or if the instructions in this manual or any “Special In-
structions” are not sufficient for you.
Luggage Rack Adjustment (various models)
1. Loosen Adjustment Knob (B) by turning counter clockwise.
2. Slide Adjustable Rack (A) into position
3. Tighten with Adjustment Knob by turning clockwise.
NOTE: Do not over-tighten. This will damage the Knob.
B
A
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Tires
Maintenance:
• Frequently check the tire inflation pressure because all tires lose air slowly over
time. For extended storage, keep the weight of the bicycle off the tires.
• Do not use unregulated air hoses to inflate the inner tubes. An unregulated hose
can suddenly over inflate bicycle tires and cause them to burst.
• Replace worn tires.
WARNING: Do not ride or sit on the bicycle if a tire is under inflated. This can
damage the tire, inner tube or wheel.
Inflating the Tires:
• Use a hand or a foot pump to inflate the tires.
• Service station meter-regulated air hoses are also acceptable.
• The maximum inflation pressure is shown on the tire sidewall.
• If two inflation pressures are on the tire sidewall, use the higher pressure for on-
road riding and the lower pressure for off-road riding.
• The lower pressure will provide better tire traction and a more comfortable ride.
Before adding air to any tire, make sure the edge of the tire (the bead) is the same
distance from the rim, all around the rim, on both sides of the tire. If the tire does not
appear to be seated correctly, release air from the inner tube until you can push the
bead of the tire into the rim where necessary. Add air slowly and stop frequently to
check the tire seating and the pressure, until you reach the correct inflation pressure.
See fig 17.
fig 17
Tire Bead Seated Correctly
Tire Bead NOT Seated Correctly
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Brake System
NOTE: The front and rear brake adjustments are the same.
WARNING: You must adjust the front and rear brakes before you ride the
bicycle.
Step 1: Put the brake shoes (B) in the correct position (fig 13):
1. Loosen the Screw (A) of each Brake Shoe (B).
2. Adjust each Brake Shoe so it is flat against the rim and aligned with the curve of
the rim.
3. Make sure each Brake Shoe does not rub the tire.
4. If the surface of the Brake Shoe has arrows, make sure the arrows point toward
the rear of the bicycle.
5. Hold each Brake Shoe in position and tighten the Screw.
C
B
D
A
fig 13
Step 2: Test the tightness of each Brake Shoe:
1. Try to move each Brake Shoe out of position.
2. If a Brake Shoe moves, do Step 1 again, but tighten the nut tighter than before.
3. Do this test again, until each Brake Shoe does not move.
continued >>
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Brake System - continued
Step 3. Tightening the cable (fig 13):
1. Hold both Brake Shoes against the rim.
2. Loosen the cable clamp Screw (C).
3. Pull the Cable (D) tight and tighten the Screw.
WARNING: Do not over tighten the cable clamp Screw. Over tightening the
cable clamp Screw may cut the cable and cause injury to the rider or to others.
Stretching the Cable:
4. Squeeze each brake lever firmly 20 times.
5. Hold both Brake Shoes against the rim and loosen the cable clamp Screw.
6. Pull the Cable tight and tighten the cable clamp Screw.
Final Brake Adjustment Before Riding
The following sections describe final brake system adjustments required be-
fore riding.
Check tightness of the cantilever mounting Bolt (A) (fig 14):
• Make sure each cantilever mounting Bolt is tightened securely.
Center brake shoes on rim:
1. Turn the Adjustment Screw (B) on the cantilever arm to move the arm in or out so
each Brake Shoe (C) is the same distance from the rim.
2. Squeeze the brake lever two times.
3. Do this step again, until both brake shoes are the same distance from the rim.
fig 14
C
B
A
continued >>
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Brake System - continued
Put the brake shoes the correct distance from the rim (fig 15):
1. If desired, adjust Brake Levers (G) to a comfortable distance from the grip using
the Adjustment Screw (H). Turning the screw IN brings it closer to the grip.
2. Make sure brake line Sheaths (A, B) are seated correctly.
3. Position each Brake Shoe 1/16 inch away from the rim:
4. Turn the caliper brake adjusting Screws (D) in or out to make the adjustment.
5. If the brake shoes cannot be positioned the correct distance from the rim, hold
both Brake Shoes against the rim and loosen the cable clamp Screw (E)
6. Squeeze the Brake Arms (F) together and pull or loosen the cable wire slightly.
7. Tighten the cable clamp Screw.
A
E
F
C
D
1/16” 1/16”
G
H
fig 15
B
continued >>
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Brake System - continued
WARNING: Do not over tighten the cable clamp. Over tightening the cable
clamp may cut the cable and cause injury to the rider or to others.
1. Repeat these steps until the brake shoes are 1/16 inch from the rim and the
Brake Lever (G) does not go all the way to the grip when squeezed (fig 15).
WARNING: Do not move the brake shoes away from a wheel rim that is not
true (straight). This can cause the caliper brake to be less effective and unsafe. To al-
low safe adjustment of the caliper brake, have a bicycle service shop true the wheel.
Test the tightness of the cable clamp (fig 15):
1. Squeeze each Brake Levers (G) with firm pressure.
2. Make sure the cable does not move in the Cable Clamp (E).
3. If the cable moves in the cable clamp, adjust the brakes again but tighten the
cable clamp tighter than before.
4. Do this test again, until the cable does not move in the cable clamp.
Test the travel of each brake lever:
1. Squeeze each Brake Lever (G)
G
with strong pressure
2. If the brake lever touches the grip,
adjust the brakes again.
WARNING: After you adjust the brakes again, if either brake lever touches the
grip or does not work well, have a bicycle service shop repair or adjust the brakes.
continued >>
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Shift System
Note: Various models have different handlebar shifters and derailleurs, but the func-
tions and instructions are the same.
Parts of the Shift System:
• Right-hand Shift Lever (A) operates the Rear Derailleur (B).
• Rear Sprocket Set (C).
A
C
B
Operation:
Operate the shift system as follows:
1. The rider turns the rear shift control around the handlebar (for twist shift models)
or moves the shift lever (thumb shift models) to an index position
2. When the rear shift control moves into each position with a “click” sound, the shift
is complete
3. The shift control pulls a cable wire that is attached to the rear derailleur.
4. The derailleur moves and guides the chain from one sprocket to another.
5. If there is some chain noise after the shift, turn the rear shift control a small
amount to “trim” the rear derailleur.
continued >>
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Shift System - continued
CAUTION: Do not force the shift lever. Shift only when pedaling forward and
without strong force. Do not backpedal. Backpedaling can cause the chain to come
off the sprockets. Backpedaling and shifting while not pedaling can damage the
sprockets and stretch the cable wire.
There is no “correct gear” in which to ride the bicycle. The “correct gear” is the one
that is comfortable to you.
To select a gear while riding (this model has only one Front Sprocket (A)).
1. While pedaling, shift the chain onto different rear sprocket.
2. You will feel a difference in the rhythm and ease of pedaling.
3. Shift the chain to the gear that allows you to pedal at a rhythm and effort that is
comfortable to you.
4. When riding uphill or against the wind, you may wish to shift the chain onto a
larger rear sprocket (B).
B
A
fig 16
continued >>
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Derailleur Adjustments
The rear derailleur has two adjusting screws. The “low” adjusting screw, sometimes
marked “L”, limits how far the rear derailleur and chain can move toward the wheel.
The “high” adjusting screw, sometimes marked “H”, limits how far the rear derailleur
and chain can move away from the wheel.
A
B
fig 21
Put the “high” adjusting screw in the correct position as follows (fig 22):
• Shift the chain onto the smallest rear sprocket. Loosen Nut (C) of the cable
clamp.
• Turn the lever Barrel Adjuster (A) and rear Derailleur Adjustor (B) all the way IN.
• Turn the “high” adjusting Screw (G) so the Jockey Roller (D) is in line with the
outside edge of the smallest rear Sprocket (E).
• Remove the slack from the cable wire and tighten the Nut of the cable clamp.
E
D
G
H
F
C
fig 22
continued >>
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Derailleur Adjustments - continued
Put the “low” adjusting Screw in the correct position as follows (fig 22):
• Shift the chain onto the largest rear Sprocket (F).
• Loosen Nut of the cable clamp.
• Turn the “low” adjusting Screw (H) so the Jockey Roller is exactly below the larg-
est rear sprocket.
• Tighten the Nut of the cable clamp.
Adjust the Index Shift System:
• Shift the chain onto the smallest rear sprocket.
• Without turning the crank, turn the Right Shift Control (A) one “click” rearward.
• Slowly turn the crank forward.
• The chain should move from the smallest rear sprocket to the next larger rear
sprocket.
• Turn the Adjusting Barrel (B) OUT as needed so the chain moves exactly on to
the second rear sprocket and does not rub, jump, or delay.
B
A
fig 23
When adjusted properly, the shift system will operate smoothly with no chain rubbing.
Note: If you have trouble, take the bike to a bike shop.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection of the Bearings
Maintenance
Frequently check the bearings of the bicycle. Have a bicycle service shop lubricate
the bearings once a year or any time they do not pass the following tests:
Head Tube Bearings
The fork should turn freely and smoothly at all times. With the front wheel off the
ground, you should not be able to move the fork up, down, or side-to-side in the head
tube.
Crank Bearings
The crank should turn freely and smoothly at all times and the front sprockets should
not be loose on the crank. You should not be able to move the pedal end of the crank
from side-to-side.
Wheel Bearings
Lift each end of the bicycle off the ground and slowly spin the raised wheel by hand.
The bearings are correctly adjusted if:
• The wheel spins freely and easily.
• The weight of the spoke reflector, when you put it toward the front or rear of the
bicycle, causes the wheel to spin back and forth several times.
• There is no side-to-side movement at the wheel rim when you push it to the side
with light force.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
WARNING:
• Do not over lubricate. If oil gets on the wheel rims or the brake shoes, it will re-
duce brake performance and a longer distance to stop the bicycle will be neces-
sary. Injury to the rider or to others can occur.
• The chain can throw excess oil onto the wheel rim. Wipe excess oil off the chain.
• Keep all oil off the surfaces of the pedals where your feet rest.
• Using soap and hot water, wash all oil off the wheel rims, the brake shoes, the
pedals, and the tires.
• Rinse with clean water and dry completely before you ride the bicycle.
• Using a light machine oil (20W), lubricate the bicycle according to the following
table:
Lubrication Table
What
Pedals
When
How
every six months Put four drops of oil where the axles go into
the pedals.
Chain
every six months Put one drop of oil on each roller of the chain.
Wipe all excess oil off the chain.
Derailleurs
Brake Levers
every six months Put one drop of oil on each pivot point of the
derailleurs.
every six months Put one drop of oil on the pivot point of each
brake lever.
Cantilever
Brakes
every six months Put one drop of oil on the pivot point of each
cantilever brake.
Brake and
cable
every six months Put four drops of oil into both ends of each
cable. Allow oil to soak back along the cable
wire.
Rear Sprocket
Cluster
every six months Lay the bicycle on its left side. Slowly turn the
rear wheel clockwise. Put four drops of oil in
the crack between the rear sprockets (which
are stationary) and the freewheel body
(which is turning clockwise).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Huffy Corporation Limited Warranty
• Part or model specifications are subject to change without notice.
• This Limited Warranty is the only warranty for your Huffy Corporation (“Huffy”) prod-
uct. There are no other expressed or implied warranties.
• This Limited Warranty extends only to the original consumer and is not transferable
to anyone else.
• Warranty registration is not required.
• The only uses for this product are described in this manual.
What does this Limited Warranty cover?
This Limited Warranty covers all parts of the bicycle.
What must you do to keep the Limited Warranty in effect?
This Limited Warranty is effective only if:
• Bicycle is completely and correctly assembled.
• Bicycle is used under normal conditions for its intended purpose (see the following
section for excluded activities).
• Bicycle receives all necessary maintenance and adjustments.
• Bicycle is used for general transportation and recreational use only.
What is not covered by this Limited Warranty?
• This Limited Warranty does not cover normal wear and tear, normal maintenance
items, or any damage, failure, or loss that is caused by improper assembly, mainte-
nance, adjustment, storage, or use of the bicycle.
This Limited Warranty will be void if the bicycle is ever:
• Used in any competitive sport
• Used for stunt riding, jumping, aerobatics or similar activity
• Installed with a motor or modified in any other way
• Ridden by more than one person at a time
• Rented
• Used in a manner contrary to the instructions and warnings in this Owner’s Manual
Huffy will not be liable for incidental or consequential loss or damage, due directly or
indirectly from use of this product. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation may not apply to you.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Huffy Corporation Limited Warranty - continued
For how long does this Limited Warranty last?
• The frame is warranted for life.
• Aluminum frames are warranted for ten (10) years.
• The fork is warranted for life except for shock and aluminum forks which are war-
ranted for one (1) year.
• Electronics are warranted for 90 days.
• Batteries have no warranty
• All other components are warranted for six (6) months.
• All warranties are from date of purchase and for the original owner.
What will Huffy do?
Huffy will replace, without charge to you, the component found to be defective by Huffy.
The original owner must pay all labor and transportation charges connected with the
repair or warranty work.
How do you get service?
Contact Huffy Consumer Service.
See included list for Customer Contact information.
What rights do you have?
This warranty gives you specific legal rights. You may also have other rights which
vary from state to state.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING:
ALWAYS WEAR YOUR
HELMET WHEN RIDING
THIS PRODUCT!
CORRECT
INCORRECT
• Helmet should sit level on your head and low on your forehead
• Adjust the strap sliders below the ear on both sides.
• Buckle the chin strap. Adjust strap until it is snug.
• No more than two fingers should fit between the strap and your chin.
• A proper fitting helmet should be comfortable and not rock forward/back-
ward or side to side.
• Always read the user manual that comes with your helmet to make sure it
is fitted and attached properly to the wearer’s head according to the fitting
instructions described in the user manual.
H Helmet EN 100212 i0027
Download from Www.Somanuals.com. All Manuals Search And Download.
|