Hotpoint Cooktop CRO 642 D B User Manual

Operating Instructions

HOB

Contents

Installation, 2-4

Positioning

Electrical connection

Description of the appliance, 5-6

Control panel

English,1

Extendable cooking zones

Start-up and use, 7-10

Switching on the hob

Switching on the cooking zones

Switching off the cooking zones

Power function

Heating elements

Programming the cooking duration

Timer

Control panel lock

Switching off the hob

“Demo” mode

CRO 642 D B

CRO 742 DO B

Practical advice on using the appliance

Safety devices

Practical cooking advice

Precautions and tips, 11

General safety

Disposal

Care and maintenance, 12

Switching the appliance off

Cleaning the appliance

Disassembling the hob

Technical description of the models, 13

After Sales Service, 14

Guarantee, 15

Key Contacts, 16

Download from Www.Somanuals.com. All Manuals Search And Download.

.ixing

Single-phase connection

The appliance must be installed on a perfectly level

supporting surface.

The hob is equipped with a pre-connected electricity

supply cable, which is designed for single-phase

connection. Connect the wires in accordance with

the instructions given in the following table and

diagrams:

Any deformities caused by improper fixing could

affect the features and operation of the hob.

The thickness of the supporting surface should be

taken into account when choosing the length of the

screws for the fixing hooks:

Voltage and

mains frequency

Electrical cable

Wire connection

• 30 mm thick: 17.5 mm screws

• 40 mm thick: 7.5 mm screws

: yellow/green;

N: the two blue wires

together

L: brown and black

together

230-240V 1+N ~

220-240V 1+N ~

50/60 Hz

;ix the hob as follows:

1. Use short flat-bottomed screws to fix the 4

alignment springs in the holes provided at the

central point of each side of the hob.

Other types of connection

2. Place the hob in the cavity, make sure it is in a

central position and push down on the whole

perimeter until the hob is stuck to the supporting

surface.

If the mains supply corresponds with one of the

following:

Voltage and mains frequency

• 400V - 2+N ~ 50/60 Hz

3. ;or hobs with raised sides: After inserting the hob

into its cavity, insert the 4 fixing hooks (each has its

own pin) into the lower edges of the hob, using the

long pointed screws to fix them in place, until the

glass is stuck to the supporting surface.

• 220-240V 3 ~ 50/60 Hz

• 230-240V 3 ~ 50/60 Hz

• 400V - 2+2N ~ 50/60 Hz

Separate the wires and connect them in accordance

with the instructions given in the following table and

diagrams:

! The screws for the alignment springs must remain

accessible.

Voltage and

! In order to adhere to safety standards, the

appliance must not come into contact with electrical

parts once it has been installed.

Electrical cable

Wire connection

mains frequency

400V - 2+N ~

50/60 Hz

: yellow/green;

N: the two blue wires together

L1: black

230-240V 3 ~

220-240V 3 ~

50/60Hz

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of

a tool.

L2: brown

: yellow/green;

N1: blue

400V - 2+2N ~

50/60 Hz

N2: blue

L1: black

Electrical connection

L2: brown

! The electrical connection for the hob and for any

built-in oven must be carried out separately, both for

safety purposes and to make extracting the oven

easier.

If the mains supply corresponds with one of the

following:

Voltage and mains frequency

• 400V 3 - N ~ 50/60 Hz

proceed as follows:

Terminal board

On the lower part of the

! The cable provided is not suitable for the following

appliance there is a

UNDERSIDE OF HOB

types of installation.

connection box for the

different types of electricity

supply (the picture is only an

indication and is not an exact

representation of the

1. Use a suitable supply cable, H05RR-- or higher,

with the right dimensions (cable cross section: 25

mm).

2. To open the terminal board, use a screwdriver as

a lever under the side tabs of the cover (see

Terminal board picture).

purchased model).

3. Loosen the cable clamp screw and the terminal

board screws in accordance with the type of

Download from Www.Somanuals.com. All Manuals Search And Download.

connection required and position the connection

supports as shown in the following table and

diagrams.

Connecting the electricity supply cable to the

mains

If the appliance is being connected directly to the

electricity mains an omnipolar switch must be

installed with a minimum opening of 3 mm between

contacts.

4. Position the wires in accordance with the

information given in the following table and diagrams

and connect the appliance by tightening all the

screws for the springs as much as possible.

Voltage and

mains frequency

Electrical connections

Terminal board

! The installer must ensure that the correct electrical

connection has been made and that it is fully

compliant with safety regulations.

400V 3-N ~

50/60 Hz

Three-phase 400

Before connecting the appliance to the power

supply, make sure that:

5. Secure the power supply cable by fastening the

cable clamp screw, then put the cover back on.

• The appliance is earthed and the plug is

compliant with the law.

Phase

• The socket can withstand the maximum power of

the appliance, which is indicated on the data

plate located on the appliance itself.

Three-phase 400

• The voltage falls within the range of values

indicated on the data plate.

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

Neutral

U-bolt

connection support

Earth

! Once the appliance has been installed, the power

supply cable and the electrical socket must be

easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only.

! The manufacturer declines any liability should

these safety measures not be observed.

! Do not remove or replace the power supply cable

for any reason. Its removal or replacement will void

the warranty and the CE marking. INDESIT does not

assume liability for accidents or damage arising

from replacement/removal of the original power

supply cable. Replacement can only be accepted

when carried out by personnel authorised by

INDESIT and using an original spare part.

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the

appliance

Control panel

The control panel described in this manual is only a representative example: it may not exactly match the panel

on your appliance.

• PROGRAMME TIMER display shows which

programme has been selected (see Start-up and

use).

• INCREASE TIME button increases the time value

set on the timer (see Start-up and use).

• DECREASE TIME button decreases the time

value set on the timer (see Start-up and use).

• COOKING ZONE PROGRAMMED indicator lights

show which cooking zones are being used during

a cooking programme (see Start-up and use).

• COOKING ZONE SELECTOR button shows a

particular cooking zone has been selected and

therefore various adjustments are possible.

• CONTROL PANEL LOCK button prevents

accidental changes to the hob settings (see Start-

up and use).

• COOKING ZONE SELECTOR button is used to

select the desired cooking zone.

• CONTROL PANEL LOCK indicator light shows

the control panel has been locked (see Start-up

and use).

• POWER indicator provides a visual display for the

current heat level.

• COOKING ZONE POWER SELECTOR buttons

switch on the hotplate and control the power (see

Start-up and use).

• ON/O.. button switches the appliance on and off.

• ON/O.. indicator light shows whether the

appliance is on or off.

• TIMER indicator light shows that the timer has

been activated

• PROGRAMME TIMER button controls the cooking

programme times (see Start-up and use).

Download from Www.Somanuals.com. All Manuals Search And Download.

Extendable cooking zones

Certain models are fitted with extendable cooking zones. These may be circular or oval and may vary in their

extensibility (they may be double or triple hotplates). A list of controls is given below (these controls are only

present in models with the extendable cooking zone option).

Oval extendable hotplate

Circular extendable hotplate

DOUBLE

HOTPLATE ON

indicator light

OVAL

HOTPLATE ON

indicator light

DOUBLE

HOTPLATE ON

button

OVAL

PLATE ON

button

• OVAL HOTPLATE ON button switches on the

oval hotplate (see Start-up and use).

• DOUBLE HOTPLATE ON button switches on the

double hotplate (see Start-up and use).

• OVAL HOTPLATE ON indicator light shows the

oval hotplate has been switched on.

• DOUBLE HOTPLATE ON indicator light shows

the double hotplate has been switched on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Start-up and use

! The glue applied on the gaskets leaves traces of

grease on the glass. Before using the appliance, we

recommend you remove these with a special non-

abrasive cleaning product. During the first few hours

of use there may be a smell of rubber which will

disappear very quickly.

reached. Once this level has been reached, the

display will revert to showing the set power level. To

deactivate this function, press and hold – for at least

2 seconds - the selector button corresponding to the

cooking zone on which the

function has been

activated; alternatively, select a different power level

between 0 and 9 using the power level selector

buttons.

! A few seconds after the hob is connected to the

electricity supply, a buzzer will sound. The hob may

now be switched on.

Heating elements

! If the

button is pressed for an extended

Two types of heating element may be installed,

depending on the appliance model: halogen and

radiant elements.

period of time, the display scrolls quickly though the

power levels and timer minutes.

Halogen elements emit heat via radiation from the

halogen lamps they contain.

Switching on the hob

They have similar properties to gas burners: they are

easy to control and reach set temperatures quickly,

allowing you to see the power level instantly.

Radiant elements consist of a series of coils which

allow heat to be distributed evenly at the base of the

cookware, so that all slow-flame cooking may be

performed successfully, for example stews, sauces

or reheated dishes.

To switch the hob on, press and hold the

for approximately one second.

button

Switching on the cooking zones

Each cooking zone is controlled using a selector

button and a power adjustment device

Programming the cooking duration

consisting of power level selector buttons between

the values of 0 and 9.

! All the cooking zones may be programmed

simultaneously, for a duration between 1 and 99

minutes.

• To begin operating a cooking zone, press the

corresponding control button and set the desired

power level using the power level selector buttons

between 0 and 9.

1. Select the cooking zone using the corresponding

selector button.

2. Adjust the temperature.

Switching off the cooking zones

3. Press the

programming button.

To switch off a cooking zone, select it using the

corresponding selector button

and:

4. Set the cooking duration using the

and

• Press power level selector button 0: this

immediately returns the power setting to 0 and the

cooking zone switches off.

buttons.

5. Confirm by pressing the

button.

The timer begins counting down immediately. A

buzzer sounds for approximately 1 minute and the

cooking zone switches off when the set programme

has finished.

Power function

The power function for the cooking zones may be

used to shorten heating-up times. Activate and set

Repeat the above procedure for each hotplate you

wish to programme.

the power level for the desired cooking zone

described in the previous paragraph. Press and hold

the selector button corresponding to the desired

Using multiple programmes and the display

If one or more hotplates are programmed, the

display will show the data for the hotplate with the

least time remaining, and the light corresponding to

the position of the hotplate will flash. The lights

corresponding to the other hotplates programmed

cooking zone

for at least 2 seconds. The

display, the power level indicator, will alternately

show the letter “P” and the power level set

previously until the desired power level has been

Download from Www.Somanuals.com. All Manuals Search And Download.

Switching off the hob

will be switched on.

To display the time remaining for the other

Press the

button to switch the appliance off.

programmed hotplates, press the

button

If the control panel lock has been activated, the

controls will continue to be locked even after the hob

is switched on again. In order to switch the hob on

again, you must first remove the lock function.

repeatedly. The times remaining for each hotplate

will be shown in a clockwise order, beginning with

the front left hotplate.

Changing the programme

“Demo” mode

1. Press the

button repeatedly until the duration

It is possible to set the hob to a demonstration

mode where all the controls work normally but the

heating elements do not switch on. To activate the

“demo” mode the hob must be switched on, with all

the hotplates switched off.

you wish to change is shown.

2. Use the

buttons to set the new duration.

3. Confirm by pressing the

button.

• Press and hold the

and

buttons

To cancel a programme, follow the above

instructions. At step 2, press the button: the

simultaneously for 6 seconds. When the 6

seconds have elapsed, the ON/O-- and

CONTROLS LOCKED indicator lights will flash for

duration decreases progressively until it reaches 0

and switches off. The programme resets and the

display exits programming mode.

one second. Release the

press the button;

and

buttons and

Timer

• The display will show the text DE and MO and the

hob will be switched off.

The hob must be switched on.

The timer can be used to set a duration up to 99

minutes.

• When the hob is switched on again it will be set to

the “demo” mode.

To exit this mode, follow the procedure described

above. The display will show the text DE and O-

and the hob will be switched off. When it is next

switched on, the hob will function normally.

1. Press the

programming button until the timer

indicator light is illuminated.

2. Set the desired duration using the

and

buttons.

Practical advice on using the appliance

3. Confirm by pressing the

button.

The timer begins counting down immediately. When

the time has elapsed, a buzzer will sound (for one

minute).

To obtain the best results from your hob:

• Use pans with a thick, flat base in order to fully

utilise the cooking zone.

Control panel lock

When the hob is switched on, it is possible to lock

the oven controls in order to avoid accidental

changes being made to the settings (by children,

• Always use pans with a diameter which is large

enough to cover the hotplate fully, in order to use all

the available heat.

during cleaning, etc.). Press the

button to lock

the control panel: the indicator light above the button

will switch on.

To use any of the controls (e.g. to stop cooking),

you must switch off this function. Press the

button for a few moments, the indicator light will

switch off and the lock function will be removed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety switch

• Make sure that the base of the cookware is

always clean and dry, in order to fully utilise and

extend the life of both the cooking zones and the

cookware.

The appliance has a safety switch which

automatically switches the cooking zones off after

they have been in operation for a certain amount of

time at a particular power level. When the safety

switch has been triggered, the display shows “0”.

-or example: the right rear hotplate is set to 5 and

will switch off after 5 hours of continuous operation,

while the front left hotplate is set to 2 and will switch

off after 8 hours.

• Avoid using the same cookware which has been

used on gas burners: the heat concentration on

gas burners may distort the base of the pan,

causing it not to adhere correctly.

Safety devices

Pan sensor

Maximum operating

Power level

time in hours

Each cooking zone is equipped with a pan sensor

device. The hotplate only emits heat when a pan

with suitable measurements for the cooking zone is

placed on it. If the indicator light is flashing, it may

indicate:

• An incompatible pan

• A pan whose diameter is too small

• The pan has been removed from the hotplate.

Residual heat indicators

Each cooking zone is equipped with a residual heat

indicator. This indicator signals which cooking zones

are still at a high temperature. If the power display

shows

, the cooking zone is still hot. It is

possible, for example, to keep a dish warm or melt

butter or chocolate. As the cooking zone cools, the

Buzzer

power display will show

. The display switches off

This can also indicate several irregularities:

• An object (a pan, cutlery, etc.) has been placed

on the control panel for more than 10 seconds.

• Something has been spilt on the control panel.

• A button has been pressed for too long. All of the

above situations may cause the buzzer to sound.

Remove the cause of the malfunction to stop the

buzzer. If the cause of the problem is not

removed, the buzzer will keep sounding and the

hob will switch off.

when the cooking zone has cooled sufficiently.

Overheating protection

If the electronic elements overheat, the hob switches

off automatically and

ꢀ

appears on the display,

followed by a flashing number. When the

temperature has reached a suitable level, this

message disappears and the hob may be used

again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Practical cooking advice

Pressure cooking

Pressure cooker

Frying

Boiling

•

Grilling

•

Crêpes

Cooking on a high flame and browning

(roasts, steaks, escalopes, fish fillets,

fried eggs)

Fast thickening (liquid juices)

Boiling water (pasta, rice, vegetables)

Milk

Slow thickening (dense juices)

Bain-marie cooking

Pressure cooking after whistle

™

-{}-

Low-flame cooking

(stews)

Reheating dishes

™

Chocolate sauce

Keeping food hot

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions and tips

! This appliance has been designed and

• Always make sure that pan handles are turned

manufactured in compliance with international safety

standards. The following warnings are provided for

safety reasons and must be read carefully.

towards the centre of the hob in order to avoid

accidental burns.

• When unplugging the appliance, always pull the

plug from the mains socket; do not pull on the

cable.

This appliance conforms to the following

European Economic Community directives:

- 2006/95/EEC dated 12/12/06 (Low Voltage) and

subsequent amendments;

• Never perform any cleaning or maintenance work

without having disconnected the appliance from

the electricity mains.

-89/336/EEC dated 03/05/89 (Electromagnetic

Compatibility) and subsequent amendments;

- 93/68/EEC dated 22/07/93 and subsequent

amendments.

• The appliance should not be operated by people

(including children) with reduced physical,

sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with

the product. These individuals should, at the very

least, be supervised by someone who assumes

responsibility for their safety or receive

preliminary instructions relating to the operation of

the appliance.

General safety

! Make sure that the air inlet behind the fan grille is

never obstructed. The built-in hob should, in fact, be

provided with suitable ventilation for the cooling of

the electronic components used in the appliance.

• The appliance was designed for domestic use

inside the home and is not intended for

• Do not look at the halogen lamps in the cooking

zones for long if they are present.

• Do not let children play with the appliance.

commercial or industrial use.

• The appliance must not be installed outdoors,

even in covered areas. It is extremely dangerous

to leave the appliance exposed to rain and

storms.

Disposal

• Do not touch the appliance when barefoot or with

wet or damp hands and feet.

• When disposing of packaging material: observe

local legislation so that the packaging may be

reused.

• The appliance must be used by adults only for the

preparation of food, in accordance with the

instructions provided in this booklet. Do not use

the hob as a worktop or chopping board.

• The glass ceramic hob is resistant to mechanical

shocks, but it may crack (or even break) if hit with

a sharp object such as a tool. If this happens,

disconnect the appliance from the electricity

mains immediately and contact a Service Centre.

• Ensure that power supply cables of other

electrical appliances do not come into contact

with the hot parts of the hob.

• The European Directive 2002/96/EC relating to

Waste Electrical and Electronic Equipment

(WEEE) states that household appliances should

not be disposed of using the normal solid urban

waste cycle. Exhausted appliances should be

collected separately in order to optimise the cost

of re-using and recycling the materials inside the

machine, while preventing potential damage to

the atmosphere and to public health. The

crossed-out dustbin is marked on all products to

remind the owner of their obligations regarding

separated waste collection.

• Remember that the cooking zones remain

relatively hot for at least thirty minutes after they

have been switched off. An indicator light

provides a warning when residual heat is present

(see Start-up and use).

-or further information relating to the correct

disposal of exhausted household appliances,

owners may contact the public service provided

or their local dealer.

• Keep any object which could melt away from the

hob, for example plastic and aluminium objects,

or products with a high sugar content. Be

especially careful when using plastic film and

aluminium foil or packaging: if placed on surfaces

which are still hot, they may cause serious

damage to the hob.

Download from Www.Somanuals.com. All Manuals Search And Download.

Care and maintenance

Switching the appliance off

Stainless steel frame (only in models with outer

frame)

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Stainless steel can be marked by hard water which

has been left on the surface for a long time, or by

cleaning products containing phosphorus.

Cleaning the appliance

After cleaning, it is advisable to rinse the surface

well and dry it thoroughly. If water is spilt on the

surface, dry it quickly and thoroughly.

! Do not use abrasive or corrosive detergents (for

example, products in spray cans for cleaning

barbecues and ovens), stain removers, anti-rust

products, powder detergents or sponges with

abrasive surfaces: these may scratch the surface

beyond repair.

! Some hobs have an aluminium frame which is

similar to stainless steel. Do not use any cleaning or

degreasing products which are not suitable for use

with aluminium.

! Never use steam cleaners or pressure cleaners on

the appliance.

Disassembling the hob

• It is usually sufficient simply to wash the hob

using a damp sponge and dry it with absorbent

kitchen towel.

If it is necessary to disassemble the hob:

1. Loosen the screws fixing the alignment springs on

each side.

2. Loosen the screws holding the fixing hooks in

each corner.

3. Take the hob out of its installation cavity.

• If the hob is particularly dirty, rub it with a special

glass ceramic cleaning product, then rinse well

and dry thoroughly.

! Do not attempt to repair the appliance yourself. If

the appliance breaks down, contact a Service

Centre.

• To remove more stubborn dirt, use a suitable

scraper. Remove spills as soon as possible,

without waiting for the appliance to cool, to avoid

residues forming crusty deposits. You can

achieve excellent results by using a rust-proof

steel wire sponge - specifically designed for

glass ceramic surfaces - soaked in soapy water.

• If any plastic or sugary substances are

accidentally melted on the hob, remove them

immediately with the scraper, while the surface is

still hot.

• Once it is clean, the hob may be treated with a

special protective maintenance product: the

invisible film left by this product protects the

surface from drips during cooking. This

maintenance task should be carried out while the

appliance is warm (not hot) or cold.

• Always remember to rinse the appliance well with

clean water and dry it thoroughly: residues can

become encrusted during subsequent cooking

processes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical description of

the models

This table provides a model-by-model list of the energy absorption values, type of heating elements and

diameters of each cooking zone.

Hobs

CRO 642 D B

CRO 742 DO B

Cooking zone

Back Left

Back Right

Front Left

Power (W)

HD 2200/1000

Diameter (mm)

210/140

160

Power (W)

HD 2200/1000

Diameter (mm)

210/140

145

H 1400

H 1200

145

H 1200

145

Front Right

Total power

HD 1700/700

180/120

HO 2400/1500

170x260

6500

7000

Key:

H = single hilight

HO = oval hilight

HD = double hilight

Download from Www.Somanuals.com. All Manuals Search And Download.

After Sales Service

"No company is better positioned to offer an after sales service on a

Hotpoint appliance than us - the manufacturer"

As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and

labour guarantee for the first 12 months. In addition to this you also have the advantage of free

replacement parts for the first 5 years when fitted by a Hotpoint

engineer. When the 12 months parts and labour guarantee expires we offer the following after sales service

options:

Repair Service and Information Help Desk

UK: 08709 066066

www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the Model number and the Serial number of your appliance

Available 364 days a year with a fast, effective and value for money service. We have the largest white goods

repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts and labour

guarantee for 12 months from the date of the repair.

If you require any information or have any questions about your appliance, our operators are on hand with help

and advice.

All this ensures that you will receive the best available after sales service possible.

Extended Warranties

UK: 08709 088 088

www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover plans

to give you total peace of mind.

● Repair Protection Plan -

● Kitchen Cover

ꢀREE service repairs for a single Hotpoint appliance during the period

of cover.

ꢀREE service repairs for all your Hotpoint appliances less than 8

years old.

Genuine Parts and AccessoriesUK: 08709 077 077

www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

A wide range of genuine parts and accessories are available from our hotline or through our web site.

Genuine parts and accessories, extended warranties and service repairs are all

available on our web-site at:

www.theservicecentre.co.uk

Download from Www.Somanuals.com. All Manuals Search And Download.

Guarantee

"Satisfaction guaranteed or your money back"

We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have

purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair

service or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for

an engineer to call. If the technical problem is not resolved under this guarantee, we will replace

your machine or, if you prefer, give you your money back.

All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free

replacement parts for the first 5 years (except microwaves, selected integrated appliances and

cooker hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.

Guarantee terms and conditions

Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the

following provisions that your appliance:

●

Has been installed and used correctly in accordance with this instruction booklet.

Has been used solely for domestic purposes and is located on domestic premises (ie. not for

commercial or trade use).

●

Has been properly connected to a suitable electrical supply voltage as stated on the appliance

rating plate.

Has not been subject to misuse, accident, modified or repaired by anyone other than one of our

own service engineers.

)or pre purchase information on any other Hotpoint product call: 08701 50 60 70

or visit: www.hotpoint.co.uk

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to

use quality recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully.

To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the

appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged

into a mains socket, and the door cannot be locked shut.

Download from Www.Somanuals.com. All Manuals Search And Download.

04/2008 - 195069881.00

XEROX BUSINESS SERVICES

Key Contacts

After Sales Service

Over 1200 trained specialists, directly employed by us, ensure that you can have complete

confidence in both the appliances and services we offer.

Repair Service and Information Desk

UK: 08709 066 066

(Open 8 to 8 Mon - )ri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)

www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the following information:

Model number:

Serial number:

Extended Warranties

UK: 08709 088 088

(Open 8 to 8 Mon - Sun)

www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Genuine Parts and Accessories

UK: 08709 077 077

(Open 8-30 to 5-30 Mon - )ri & 9 to 12 Sat)

www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Sander G0472 User Manual
Grundig Car Satellite TV System 32 VLE 7229 BF User Manual
Hans Grohe Plumbing Product 320XX User Manual
Hans Grohe Plumbing Product 04073XX0 User Manual
HP Hewlett Packard Network Card HP GbE2c User Manual
Hubbell Switch LXi 1600 User Manual
Humax Satellite TV System IR 5410Z User Manual
IBM Laptop 27L3405 User Manual
Icom Weather Radio IC R8500 User Manual
iHome Home Theater System iBN27 User Manual