Instruction booklet
TUMBLE DRYER
Contents
GB
GB
Important information, 2-3
Product data, 3
English
Installation, 4
Where to put your dryer
Ventilation
Water Drain
Electrical connection
Before you start using your dryer
Dryer description, 5
The features
Control panel
The Display, 6-8
Start and programmes, 8-12
Choosing a programme
Table of programmes
TCUD 97B
The controls
First time you turn on your dryer
you must select your preferred
language see page 6
Laundry, 13-14
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 15
General safety
Saving energy and respecting the environment
Maintenance and Care, 16
Switching off the electricity
Cleaning the filter after each cycle
Empty the water container after each cycle
Check the drum after each cycle
Cleaning the condenser unit
Cleaning the dryer
Troubleshooting, 17
Service, 18
Disposal
Hotpoint Guarantee, 19
Hotpoint After Sales Service, 20
! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the
dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.
! Read these instructions carefully; the following pages contain important information on installation and suggestions
on how the appliance works.
This symbol reminds you to read this booklet.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Condenser Unit...
GB
! You MUST clean the fluff from the condenser EVERY
month.
STEP 3.
STEP 4.
STEP 1.
STEP 2.
Flush the condenser, from
the rear with water, to
remove any fluff deposits.
Refit the condenser unit
- ensure that the unit is
pushed in fully, all 3 clips
are re-secured and the
positiong arrows on the
front of the condenser are
pointing upwards.
Open the condenser cover
- hold the handle and
pull towards you.
Remove the condenser by
rotating the 3 clips then
pulling the condenser
towards you.
(There may be some water
in the tubes, this is normal).
●
Check that:
- The positioning arrows are pointing upwards.
- The 3 clips are re-secured back into their ‘lock’ position.
! Failure to clean the condenser could cause premature
failure of your dryer.
Rotate 3 clips
Product Data... (EU Regulation 392/2012)
Rated capacity of Cotton laundry for the standard programme at full load 9 kg
Energy efficiency class B
The weighted Annual Energy Consumption (AEc) 616.1 kWh
Consumption per year, based on 160 drying cycles of the standard cotton programme at full and partial load, and the
consumption of the low-power modes. Actual energy consumption per cycle will depend on how the appliance is used.
This household tumble dryer is an Automatic Condenser Dryer
Energy consumption : full load Edry 5.22 kWh, partial load Edry1/2 2.81 kWh
Power consumption : off-mode (Po) 0.17 W, left-on mode (Pl) 3.27 W
Duration of the ‘left-on mode’ for power management systems 30 minutes
The ‘standard cotton programme’ suitable for drying normal wet cotton laundry that is the most efficient programme in
terms of energy consumption for cotton used at full and partial load is Cottons - Cupboard Dry (with the dryer
plumbed into a drain).
Programme time (minutes) : weighted (Tt) full & partial load 114, full load (Tdry) 153, partial load (Tdry1/2) 85
Condensation efficiency class B
Average condensation efficiency (%) : full load (Cdry) 84, partial load (Cdry1/2) 84, weighted (Ct) full & partial load 85
Airborne acoustical noise emissions 69 dB(A) re 1 pW
This data is also available on the website http://www.hotpoint.eu/hotpoint/
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Where to put your dryer
Electrical connections
GB
●
Place your dryer at a distance from gas ranges,
Make sure of the following before you insert the plug
into the the electrical socket:
stoves, heaters, or cook tops because flames can
damage the appliance.
●
Ensure your hands are dry.
The socket must be grounded.
The socket must be able to sustain the machines
Minimum gap 10mm
●
If you are going to install the
●
appliance under a work
counter, be sure to leave a
10mm space between the
top and any other objects
on or above the machine and
●
maximum power, which is indicated on the rating label
(see Dryer Description).
Power voltage must be within the values indicated on
●
Minimum gaps
the rating label (see Dryer Description).
The socket must be compatible with the dryers plug.
15mm
●
a 15mm space between the
sides and lateral furnishings
or walls.
Should this not be the case, replace the plug or the socket.
! Do not use extension cords.
! The dryer must not be installed outdoors, even if the space is
sheltered. It can be very dangerous if it is exposed to rain or
storms.
This is to ensure proper air circulation.
! Once installed, the dryers electrical wire and plug must be
within easy reach.
Ventilation
When the dryer is in use, there has to be adequate
ventilation. Make sure you put your dryer in an
environment that is not damp and has proper air
circulation throughout. Airflow around the dryer is
essential to condense the water produced during the
washing, the dryer will not operate efficiently in an
enclosed space or cupboard.
! If using the dryer in a small or cold room some
condensation could be experienced.
! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed
behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the dryer door.
! The power cord must not be bent or squashed.
! The power cord supplied is fitted with a BS1363 plug and a 13
amp BS1362 fuse. If you need to replace the fuse, use only
those rated at 13 amp (13A) and ASTA approved to BS1362.
Moulded plug
! The plug must not be used
without the fuse cover in place.
If a replacement fuse
holder/cover is required, it must
be of the same colour coding or
wording as shown on the base of
the plug.
Replacements are available from
authorised dealers.
Changing the plug
Water drain
The wires in the power cord are coloured in
accordance with the following:
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3' (1m)
from the bottom of the dryer.
Green and Yellow
(Earth) wire to terminal
marked ‘E’, symbol
or coloured green and
yellow.
,
13A ASTA approved
fuse to BS1362.
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
Brown (Live) wire to
terminal marked ‘L’ or
coloured red.
Note: If you have washed laundry in a washing machine
with a spin speed below 1100 rpm and you are drying
loads of 8 kg or more (also for energy label tests to EU
Regulation 392) you will need to plumb the dryer into a
drain, or the water container may fill before the clothes
are dry. Follow the instructions below :
Cord clamp
! If the plug being replaced is a non-rewirable type,
then the cut-off plug must be disposed of safely. DO
NOT leave it where it can be inserted into a socket and
create a shock hazard.
Remove hose from position shown
(see diagram).
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this dryer
and fitted only by authorised technicians (see Service).
New or longer power cords are supplied at an extra
charge by authorised dealers.
Remove hose from
here...
! The manufacturer denies any responsibility should
any of these rules not be followed.
! If in doubt about any of the above consult a
qualified electrician.
Fit a suitable length of hose to the
new location shown (see diagram).
...fit new hose here.
Before you start using your dryer
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any dust
that could have accumulated during transport.
! Make sure that the hose is not squashed or kinked when
the dryer is in its final location.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer Description
The features
GB
Water container
Model & Serial numbers
Rating plate
Filter
Condenser cover handle
(Pull to open)
Condenser cover
Air intake grille
Control panel
PROGRAMME
Selection Buttons
Display Unit
CHILD LOCK &
OPTIONS
Buttons & Lights
ON/OFF
Button
START/PAUSE
Button & Light
The ON/OFF button
- if pressed when the dryer is
flashing green if on standby waiting to start a programme
(see Start and Programmes).
running: If the display shows TURNING OFF the
dryer stops. If the display shows PRESS AND HOLD
hold the botton and the display counts down 3, 2, 1
and then stops.
Note: This light also flashes amber during the Post
Care phase of a programme.
Press and hold again for more than 3 seconds, the
display briefly shows POWER ON .
The Display Unit gives warnings and information
about the programme selected and its progress (see
next page).
The PROGRAMME selection buttons set the programme:
press the button corresponding to the programme you
want to select (see Start and Programmes).
The CHILD LOCK button/icon
: Press and hold this
button after selecting your programme and any options,
this prevents the programme settings from being
changed, the display will briefly show LOCKED .
When the icon is lit, the other buttons are disabled.
Hold the button to cancel and the icon will go out, the
display will briefly show UNLOCKED .
The OPTION buttons/indicators: these buttons select
available options for your selected programme (see
The Controls). The indicators on the display unit next
to the bottom buttons light to show that the option has
been selected.
Note: This tumble dryer, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press and hold the ON-OFF
button until the display briefly shows POWER ON
and the dryer then reactivates.
The START/PAUSE button/light
starts a selected
programme. When a programme is running, holding this
button in pauses the programme, there will be one
beep,the display will show PAUSE and the dryer
stops.
The light is green when the programme is running,
flashing amber if the programme has been paused or
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Display
Selecting your language
The first time you turn on your dryer you should select your preferred language from the available list.
GB
To change: the language current selection must flash, on
the first line of the display.
- Press the On/Off button to turn off the display then press
and hold all 3 buttons:
Heat Level,
Timed Dry
and
Dryness Level for 5 seconds.
- Press the
Heat Level or the
Timed Dry button to
scroll up or down through the list.
- When your required language is flashing on the top line
of the display, pressing the
select your choice.
Dryness Level button will
Understanding the display
Programme selection and display
The selected programme is shown on the first line of the display,
this message is shown while the programme is running.
Eight of the buttons have two selections, press the button once for the
first choice and press again for the second choice, your selected
programme is displayed. The final button selects My Cycle.
First Press
Second Press
1
2
3
4
5
6
7
8
9
COTTONS
SHIRTS
BED & BATH
SYNTHETICS
JEANS
ANTI ALLERGY
TURBO DRY
DUVET
WOOL
SILK
BABY DELICATES
CUDDLY TOYS
EASY IRON
DARK
HEAT & ENJOY
REFRESH
MY CYCLE (see below)
My Cycle When you select the My Cycle button the Display will show your selected programme with ‘M’ before its
name. ie. M COTTONS (see Start and Programmes).
Dryness levels
During programme selection for an automatic programme that has different dryness levels available (see Programmes
Table).
The second line of the display shows the dryness level you require, for each
press of the
Dryness Level button the next option from the list below is
selected and displayed. The display also shows 1 to 7 bars depending on
your selection and these are displayed during the programmes progress.
! Some automatic programmes do not allow the dryness level to be changed
or do not have all the dryness level options.
DAMP
Dries your items ready to be ironed using a machine or rotary ironer.
IRON DRY
Dries your items ready to be ironed with a hand iron.
Dries your delicate items ready to be hanged for final drying.
Dries your items ready to be hanged for final drying.
Dries your delicate items ready to be put away.
Dries your items ready to be put away.
HANGER PLUS
HANGER DRY
LIGHT DRY
CUPBOARD DRY
EXTRA DRY
Dries your clothes ready to be worn.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Display
Programme progress
GB
The second line of the display shows the status of the programme as it progresses:
(long messages scroll across the line)
DRY
COOL TUMBLE
Heat & Enjoy programme
HEATING
READY
END OF CYCLE, CREASE CARE
(if option Crease Care selected).
END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
Timed drying
After selecting a programme that has a Timed Dry option,
press the Timed button and the display will increment the
selected time, each time you press and release the button
(see Start and Programmes).
Each press reduces the time duration and number of available time options depending on the programme/material
selected.
The Timed Dry icon
is displayed next to the time.
The selected time remains displayed after the programme starts, but can be changed anytime you wish.
Delay and Time to End
Some programmes can have a delayed start (see Start and Programmes). Press the
Each press of the Delay button advances the delay setting
Delay button and the icon flashes.
in 1 hour increments, from: , then and
to
24h
1h
OFF
then after a couple of seconds cancels the delay.
The delay time is shown on the display next to the Delay button.
The display counts down the minutes of the delay period after
the Start/Pause button
is pressed.
The second line of the display shows STARTS IN
You can change or cancel the delay time selected anytime if you
wish.
After the Start/Pause button is pressed the Delay or Time to End is displayed in hours and minutes and counts down each
minute.
Time to End
After the delay period finishes, or for all the programme if delay not selected, this part of the display will show:
- the estimated time to the end of the programme, for automatic programmes
- the actual time remaining during a timed programme
When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.
When Automatic programmes are selected the time displayed is an estimate of the time remaining. When the
programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller
calculates a better estimate of the cycle time and this is updated during the programme.
The colons between the hours and minutes in the display flash to show the time is counting down.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The Display
Warnings
GB
The second line of the display also gives warnings and reminders:
(reminders occur at the end of the programme)
END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
●
Reminder that the water container should be
emptied and the filter cleaned every time you use the
dryer (see Maintenance).
CLEAN CONDENSER, FILTER AND EMPTY WATER BOTTLE
EMPTY WATER BOTTLE
●
This message indicates that you must clean the
Condenser unit (see Maintenance) and will occur
at intervals depending how much you have used
the dryer. When you finish the next programme the
message is cancelled. You must also clean the filter.
●
Indicates that the water container is full. The
message will take a few seconds to go out after
replacing the empty water container; the dryer
must be running for this to happen (see The
Controls).
Note: If the water container fills and this message
is displayed, the heat is turned off and your
clothes will not dry.
CLEAN FILTER TO ENSURE ANTI ALLERGY ACTION
●
Shown during the Anti-Allergy programme and
indicates that the filter needs cleaning to complete
the full anti-allergy cycle (see Maintenance).
Start and Programmes
Choosing a programme
8. Set a delay time and other options if necessary
(see The Display).
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
and in place and the water container is empty and
in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. If the Display is not lit: Press the ON/OFF button
6. Press the Programmes Selection button that
corresponds with the type of fabric being dried by
checking the Programmes Table (see Programmes)
as well as the indications for each type of fabric (see
Laundry).
9. Press the Start/Pause button
to begin.
The display will show the estimated time to end.
During the drying programme, you can check on
your laundry and take out items that are dry while
others continue drying. When you close the door
again, press the Start/Pause button
resume drying.
in order to
10. During the last few minutes of Drying Programmes,
before the programme is completed, the final COOL
TUMBLE phase is entered (fabrics are cooled),
this phase should always be allowed to complete.
11. At the end of the drying cycle a message is
displayed:
-
If END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
is shown, the buzzer will beep 3 times (Note: If
the SOUND option was selected the buzzer
beeps 3 times every 30 seconds for 5 minutes).
If END OF CYCLE, CREASE CARE is shown, Crease
Care option has been selected and if you do
not remove the laundry immediately, the
- If the
button is selected; steps 7 and 8 are not
required (see below).
7. Choose Timed Drying or Dryness Levels option:
- If Timed Drying press and release the Timed
button until the required time is displayed.
or - To change from default dryness setting, press
and release the Dryness Levels button until
required level is indicated.
-
dryer will tumble occasionally for 10 hours or
until you open the door, the buzzer will beep
3 times to confirm the programme is completed.
! See Programmes Table, for more details:
availability of Dryness Levels, Timed Dry and
Options.
12. Open the door, take the laundry out, clean the filter
and replace it. Empty the Water Container and
replace it (see Maintenance).
13. Unplug the dryer.
My Cycle button:
First time you press this button the display will show PRESS AND HOLD TO STORE
After selecting your favorite programme and options you can save these settings by pressing and holding in the
My Cycle button for at least 5 seconds, the top line will show a flashing
buzzer will then beep and the second line of the display shows MEMORY
followed by the selected programme. The
The next time you need this programme press the button, then the Start/Pause button
If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold
in the button (as above).
and this programme will run.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Programmes Table
! If the Display is not lit; Press the ON/OFF button
and then select programme.
GB
Dryness Levels available
Programme
Options available
(default highlighted
)
✓
- High
✓
✓
✓
✓
✓
✗
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Cottons
✓
✓
✓
✓
- Medium
- Low
✓ ✓
1
- High
✓
✗
✓
✓
✓
✓
Shirts
✓
✓
✓
✓
✓
✓
✓
✓
✗
✓
✓
- Medium
- High
✓
✗
✗
✗
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Bed & Bath
✓
- Medium
2
3
●
An Automatic programme
Anti Allergy
Synthetics
Turbo Dry
✓
✓
✓
✗
✗
✗
✗
✓ ✓
- Medium
- Low
✓
✓
✓
✓
✓
✓
✗
✓
✓
✓
✓
✓
✓
●
An Automatic programme
✗
*YOU CANNOT SELECT BOTH POST CARE AND SOUND OPTIONS
Cottons
●
●
This is a programme for cotton items.
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed
used in your washer (see Laundry).
Shirts
High heat option
●
●
This is a programme for shirts made from cotton.
It can be used for load sizes up to 3kg (approximately 10 shirts).
Medium heat option
●
This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such
as polyester and cotton.
●
●
It can be used for load sizes up to 3kg (approximately 14 shirts).
Note: The Less Fluff option is NOT available when Shirts - Medium Heat is selected.
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer.
Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If
this is the case, try turning the shirts inside out and running the programme again for a short period.
Bed & Bath
●
This is a programme for cotton towels and sheets.
●
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed
used in your washer (see Laundry).
●
Loads dried using the Extra Dry setting are usually ready to use, the edges or seams may be slightly damp especially
on large items. If this is the case, try opening them out and running the programme again for a short period.
Anti Allergy Programme
This programme has the ‘Seal of Approval’ endorsement from Allergy UK, which reflects the effective reduction and
elimination of allergens from the clothes with the special Anti Allergy cycle. With this programme, thanks to the
achievement of constant temperature for an extended period of time, the effects of the most common allergens (including
House Mites and Pollen) are neutralised.
Can be used on a full size wet load to dry and treat, or on a 4kg dry load just to treat your laundry.
If the display shows CLEAN FILTER TO ENSURE ANTI ALLERGY ACTION : Clean the filter and re-start the programme.
Synthetics
●
This is a programme for items of Synthetic with low heat setting or Synthetic/Cotton mixtures with medium heat setting.
●
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed
used in your washer (see Laundry).
Turbo Dry
This programme has an extra fast cycle to dry cottons (ie. Cottons and Bed & Bath) by using a combination of
temperature control and a special motor speed profile that takes advantage of our new Soft Motion motor system.
●
It has been optimised for a 7kg load, other load sizes will not benefit from the optimised drying speeds and therefore
may not give an improvement in drying time.
●
It dries to Hanger Dry level leaving your clothes ready to be hanged for final drying.
The duration of this programme will depend on the size of the load and the spin speed used in your washer.
●
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Programmes Table
! If the Display is not lit; Press the ON/OFF button
GB
and then select programme.
Programme
Options available
Dryness Levels available
(default highlighted
)
✓
Jeans
Duvet
✗
✗
✓
✓
✓
✓
✓
✓
✓
✗
- High
✓
✗
✗
✓
✓
✓
✓
✓
*
4
●
An Automatic programme
An Automatic programme
✗
*
✓
✗
- Medium
●
Wool
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✓
✗
5
6
Silk
✗
✗
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Baby Delicates
Dark
✓
✓
✓
✗
✓
✗
*
●
An Automatic programme
✓ ✗
*YOU CANNOT SELECT BOTH POST CARE AND SOUND OPTIONS
Jeans
●
●
●
●
●
This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.
It can be used for load sizes up to 3kg (approximately 4 pairs).
Do not mix dark and light coloured items.
It can also be used on other garments made from the same material, such as jackets.
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer.
Loads dried using the Extra Dry setting are usually ready to wear, the edges or seams may be slightly damp. If
this is the case, try turning the jeans inside out and running the programme again for a short period.
●
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.
Duvet
! Take care with this programme DO NOT dry any items that are damaged which could result in the filling blocking
the filter and air vent resulting in a fire hazard.
●
Must only be used on single size duvets: NOT suitable for double or king size items.
●
Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is the case,
try opening them out and shaking them and running the programme again for a short period.
●
Also suitable for down filled jackets.
●
Select high heat for Cotton Duvets and medium heat for Synthetic duvets
●
The duration of this programme will depend on the size and density of the load and the spin speed used in your
washer.
Wool Programme
●
This is a programme for tumble dryer safe garments marked with the symbol
It can be used for load sizes up to 1kg (approximately 3 sweaters).
We recommend that garments are turned inside out before drying.
.
●
●
●
This programme will take about 60 minutes, but may take longer depending on the size and density of the load
and the spin speed used in your washer.
●
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be
slightly damp. Allow these to dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and
shape.
! This programme is not suitable for Acrylic garments.
Silk
●
This is a programme for drying your delicate silk.
●
It can be used for load sizes up to 0.5kg.
●
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer.
●
Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be
slightly damp. If this is the case, try opening them out or turn items inside out and running the programme again for
a short period.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Baby Delicates Programme
GB
●
This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille)
and for drying your delicate clothes.
●
DO NOT dry items such as bibs and nappy pants with plastic coverings.
●
It can be used for load sizes up to 2kg.
●
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer.
●
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be
slightly damp. If this is the case, try turning items inside out and running the programme again for a short period.
Dark cycle
This programme helps to maintain your dark coloured Cotton clothes, by controlling the motor speed and drum
rotation, together with control of the lower drying temperature.
●
It can be used for cottons loads and jeans loads, up to a maximum of 3kg.
●
It dries to Cupboard Dry level.
●
As this is a treatment programme aimed to protect your dark coloured clothes, the programme duration could be
more than 4 hours.
●
The duration of this programme will depend on the size of the load and the spin speed used in your washer.
Programmes Table
! If the Display is not lit; Press the ON/OFF button
and then select programme.
Programme
Options available Dryness Levels available
(default highlighted
)
✓
●
●
An Automatic programme
An Automatic programme
✗
✗
✗
✓
✗
✗
✗
Cuddly Toys
✗
✗
✗
✗
✗
✓
✗
7
Heat & Enjoy
Easy Iron
✗
✗
✗
✗
✗
✗
●
An Automatic programme
An Automatic programme
✗
✗
✗
✗
✓
✓
✗
✗
8
9
●
Refresh
Depends on your chosen programme. See previous details.
My Cycle
M
Cuddly Toy Programme
With this programme you can remove dust easier and wash the cuddly toys more often because the drying time is
very much reduced compared to drying in the open air. It is a delicate drying cycle that dries at low temperature
and with soft mechanical action to maintain at best the original look and shine of the fur.
Note: For allergy protection, just freeze cuddly toys for 24 hours then wash and dry them. Repeat every 6 weeks.
Before drying remove accessories such as clothes, collars or sound boxes and protect plastic eyes with masking
tape after drying them with a cloth.
The programme time will vary dependant on the exact make up of the load. The maximum load should not exceed
2.5kg and no individual item should be greater than 600g.
Heat & Enjoy
This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for
warming clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature), the display
shows HEATING and runs at this temperature for a maximum of 4 hours or until you stop the cycle by opening the
door when the display shows READY . Maximum load 3kg.
Note: The Start/Pause button is disabled during this programme.
Refresh
! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.
●
It can be used on any load size, but is more effective on smaller loads.
●
Do not overload your dryer (see Laundry).
●
This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The
cycle relaxes the fibres and makes them easier to iron and fold.
GB
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:
Fabric
Maximum load
Cotton and Cotton mixtures
Synthetics
2.5kg
2kg
Denim
2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles
and put them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,
and less well on acrylic fibres and on materials such as Tencel®.
Less Fluff
The Controls
By reducing the mechanical action during the final drying
! Warning, after pressing the Start/Pause button
, the
stage the amount of lint and fluff produced is substantially
reduced, protecting the fibres of your garments.
programme cannot be changed.
To change a selected programme, press the Start/Pause
button
, the light flashes Amber to indicate the
●
88:88
TIME DISPLAY
programme is paused. Select the new programme and
any options required, the light will then flash green. Press
The display shows either the amount of time delay
remaining or an indication of the amount of time left for a
drying programme (see The Display).
the Start/Pause button
will start.
again and the new programme
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by a
fault code number (see Troubleshooting).
●
Option buttons
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected, by pressing a programme selection
button, before an option can be selected. Not all options
are available for all programmes (see Programmes
Table). If an option is not available and you press the button,
the buzzer will beep 3 times. If the option is available the
indicator, on the display unit next to the bottom buttons,
lights to show that the option has been selected.
Delay Timer (Time Delay)
●
Empty Water Container
(If you have plumbed your dryer to a drain this icon can be
ignored, as there is no need to empty the water container).
Messages are displayed to reminds you to empty the
water container (see The Display).
If the water container fills during a programme, the heater
turns off and the dryer does a period of Cool Tumble.
After this it stops and a message tells you to
EMPTY THE WATER CONTAINER .
The start of some programmes (see The Display and
Programmes tables) can be delayed for up to 24 hours.
Ensure the water container is emptied before setting a
delayed start.
You must empty the water container and restart the dryer
or the clothes will not dry. After re-starting the dryer the
message will take a few seconds to go out.
To avoid this always empty the water container each time
you use the dryer (see Maintenance).
Pre Care
This option is only available if a delayed start has been
selected. It tumbles the clothes occasionally during the
delayed period to help prevent creases developing.
Post Care
●
Door Opening
Opening the door during a programme will stop the dryer
and have the following effects:
Note: The Start/Pause light flashes Amber during the Post
Care phase of a programme.
When available and selected, the clothes are
occasionally tumbled after the end of the drying and cool
tumble cycles, to help prevent creases developing
should you not be available to remove the load
immediately the programme is complete.
●
The display shows PAUSE .
During a delay phase the delay will continue to count
down. The Start/Pause button must be pressed to
resume the delay programme.
The display will change to show current status.
During the drying part of the programme, the colons
on the display stop flashing to show that the time has
stopped counting down.
The Start/Pause button must be pressed to resume
the programme. The display will change to show the
current status, the colons flash and count down
continues.
During the Post Care phase, the programme ends.
Pressing the Start/Pause button will restart a new
programme from the beginning.
●
Note: The Start/Pause light flashes Amber during this phase.
Note: If you have selected the Sound option this option is
not available.
●
Heat Level button, Display and Icons
Not all programmes allow you to change the heat level
and some programmes allow all three heat level options:
Low, Medium and High.
When the heat level options are available pressing this
button changes the heat level and the display briefly shows
the selected heat level, along with a display of the selected
level icon:
●
HIGH HEAT
MEDIUM HEAT
LOW HEAT
Sound
●
Note
When available and selected, a buzzer gives a signal at
the end of the drying cycle, to remind you that the
clothes are ready to be removed.
If you have a power cut, switch off the power or remove
the plug. When power is restored, press and hold the
On/Off button until the display briefly shows POWER ON
and the dryer reactivates. Then press the Start/Pause
button and the programme will resume.
Note: If you have selected the Post Care option this
option is not available.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Sorting your laundry
Wash Care Labels
GB
●
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings.
Wring out each item in order to eliminate as much
excess water as possible.
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
●
●
●
May be tumble dried
●
Do not tumble dry
! Do not load dripping wet clothes into the dryer.
Tumble dry at high heat setting
Tumble dry at low heat setting
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 9kg max (20lb)
Synthetic fibres: 3kg max (6.6lb)
Items not suitable for tumble drying
●
Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
Glass fibres (certain types of draperies)
Items which have been dry cleaned
! DO NOT overload the dryer as this could result in
reduced drying performance.
Typical weights
●
●
Note: 1kg = 1000g
(1lb = 16oz)
150g
●
Items with the ITCL Code
(see Special
Clothes
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
Blouse
Cotton
(5oz)
Other
Cotton
Other
100g
500g
350g
700g
(3oz)
Dress
(1lb 2oz)
(12oz)
(1lb 6oz)
●
Jeans
10 nappies
Shirt
1000g (2lb 3oz)
Cotton
Other
300g
200g
125g
(10oz)
(7oz)
(4oz)
The Wool drying cycle
of this tumble dryer
has been tested and
T-Shirt
approved by The
Woolmark Company.
Household Items
●
The cycle is suitable to dry wool garments which
are labelled ‘hand wash’, provided that the garments
are washed in a Woolmark endorsed hand washing
cycle and tumble dried according to the instructions
issued by the manufacturer. M1219
In the UK, Eire, Hong Kong and India the Woolmark
symbol is a certification trademark :
©The Woolmark Company Pty Ltd.
Duvet cover
(Double)
Cotton
Other
1500g (3lb 5oz)
1000g (2lb 3oz)
Large Tablecloth
Small Tablecloth
Tea Towel
700g
250g
100g
700g
350g
500g
350g
(1lb 6oz)
(9oz)
(3oz)
Bath Towel
(1lb 6oz)
(12oz)
Hand Towel
Double Sheet
Single Sheet
(1lb 2oz)
(12oz)
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
●
Special clothing items
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
GB
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
●
●
Heat setting.
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to
dry your clothes.
Starched articles: do not dry these with non-starched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in
the dryer. Do not over-dry: the starch will become
powdery and leave your clothing limp, which defeats
the purpose of starch.
●
Bulk: some bulky items can be tumble dried with
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
Drying times
The table (see below) presents APPROXIMATE drying
times in Hours : Minutes, as you see them on the
display, the times are also shown in Minutes only for
reference.
Times are approximate and can vary depending
upon:
●
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
The times given are for Cupboard Dry Automatic
programmes.
●
Fabrics: items that are the same type of fabric but
different textures and thicknesses may not have
the same drying time.
Timed Dry settings are also shown, to help you
choose a suitable time option.
●
Quantity of laundry: single items or small loads
Weights refer to dry garments.
may take longer to dry.
Cottons
2 kg
3 kg
4 kg
1:10 - 1:20
70 - 80
6 kg
7 kg
1 kg
0:30 - 0:40
30 - 40
9 kg
5 kg
1:20 - 1:30
8 kg
Automatic duration
Automatic minutes
Timed Dry setting
0:40 - 0:55 0:55 - 1:10
1:35 - 2:00 2:00 - 2:20
2:30 - 2:50
140 - 170
2:40 or 3:00
2:00 - 2:40
130 - 160
2:00 or 2:40
40 - 55
55 - 70
80 - 90
1:30
95 - 120 120 - 140
High Heat
1:30
1:30 or 2:00 2:00 or 2:40
1:00
1:00 or 1:30
0:30
Drying times 800-1000 rpm in washing machine.
Synthetics
2 kg
1 kg
3 kg
1:10 - 1:30
70 - 90
Automatic duration
0:40 - 0:50
0:50 - 1:10
50 - 70
40 - 50
1:00
Automatic minutes
Timed Dry setting
High Heat
1:00
1:00 or 1:30
Drying times on reduced spin in washing machine.
Delicates
(Acrylics)
2 kg
1 kg
Automatic duration
Timed Dry only
Use
Synthetics
0:30
1:00
Timed Dry setting
Low Heat
Drying times on reduced spin in washing machine.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Suggestions
To minimise the risk of fire in your tumble dryer, the
! The appliance has been designed and built according
to international safety standards.
GB
following should be observed:
●
Tumble dry items only if they have been washed with
These warnings are given for safety reasons and must
be followed carefully.
detergent and water, rinsed and been through the spin
cycle. It is a fire hazard to dry items that HAVE NOT
been washed with water.
General safety
●
Do not dry garments that have been treated with
chemical products.
Do not tumble dry items that have been spotted or
●
This tumble dryer is not intended for use by
●
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
soaked with vegetable or cooking oils, this constitutes a
fire hazard. Oil-affected items can ignite spontaneously,
especially when exposed to heat sources such as a tumble
dryer. The items become warm, causing an oxidisation
reaction with the oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot enough to catch
fire. Piling, stacking or storing oil-effected items can prevent
heat from escaping and so create a fire hazard.
●
This tumble dryer has been designed for home,
and not professional use.
●
Do not touch the appliance while barefoot or with
wet hands or feet.
If it is unavoidable that fabrics containing vegetable or
cooking oil or those that have been contaminated with
hair care products be placed in a tumble dryer they should
first be washed with extra detergent - this will reduce, but
not eliminate the hazard. The cool tumble phase should
be used to reduce the temperature of the items. They
should not be removed from the dryer and piled or
stacked while hot.
●
Unplug the machine by pulling on the plug, not
the cord.
●
Children must not be in proximity of the dryer
when in use. After using the dryer, turn it off and
unplug it. Keep the door closed to make sure that
children do not use it as a toy.
●
Children should be supervised to ensure that they
do not play with the dryer.
The appliance must be installed correctly and
●
Do not tumble dry items that have previously been
●
cleaned in or washed in, soaked in or soiled with
have proper ventilation. The air intake at the front
of the dryer should never be obstructed (see
Installation).
petrol/gasoline, dry cleaning solvents or other flammable
or explosive substances. Highly flammable substances
commonly used in domestic environments including
cooking oil, acetone, denatured alcohol, kerosene, spot
removers, turpentine, waxes and wax removers. Ensure
these items have been washed in hot water with an extra
amount of detergent before being dried in the tumble dryer.
●
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
●
Check to see if the dryer is empty before loading it.
●
The back of the dryer could become very
●
Do not tumble dry items containing foam rubber (also
hot. Never touch it while in use.
known as latex foam), or similarly textured rubber like
materials. Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
●
Do not use the dryer unless the filter, water
container and condenser are securely in place
(see Maintenance).
●
Fabric softener or similar products should not be used in
●
Do not overload the dryer (see Laundry for
a tumble dryer to eliminate the effects of static electricity
unless the practice is specifically recommended by the
manufacturer of the fabric softener product.
maximum loads).
●
Do not load items that are dripping wet.
●
Carefully check all instructions on clothing labels
●
Do not tumble dry undergarments that contain metal
(see Laundry).
reinforcements eg. bras with metal reinforcing wires.
Damage to the tumble dryer can result if the metal
reinforcements come loose during drying.
●
Do not tumble dry large, very bulky items.
●
Do not tumble dry acrylic fibres at high temperatures.
●
Complete each programme with its Cool Tumble Phase.
●
Do not tumble dry rubber, plastic articles such as shower
●
Do not turn off the dryer when there are still warm
caps or babies waterproof covers, polythene or paper.
Do not tumble dry rubber backed articles, clothes fitted
items inside.
●
●
Clean the filter after each use (see Maintenance).
with foam rubber pads, pillows, galoshes and rubber
coated tennis shoes.
●
Empty the water container after each use (see
Maintenance).
●
Remove all objects from pockets, especially lighters
●
Clean the condenser unit at regular intervals
(risk of explosion).
(see Maintenance).
●
Do not allow lint to collect around the dryer.
! WARNING: Never stop the dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
●
Never climb on top of the dryer. It could result in damage.
●
Always follow electrical standards and requirements
(see Installation).
●
Always buy original spare parts and accessories
Saving energy and respecting the environment
(see Service).
●
Wring out items to eliminate excess water before
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
●
Always dry full loads - you save energy: single
items or small loads take longer to dry.
●
Clean the filter after each use to contain energy
consumption costs (see Maintenance).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Switching off the electricity
Cleaning the drum
GB
! Unplug your dryer when not using it, when cleaning
it and during all maintenance operations.
! Do not use abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
Clean the filter after each cycle
The filter is an important part of your dryer:
it accumulates lint and fluff that is formed while drying.
When finished drying, clean the filter by rinsing it
under running water or with your vacuum cleaner.
Should the filter become clogged up, the airflow inside
the dryer will be seriously compromised: drying times
lengthen and you will consume more energy. It may
also damage your dryer.
Cleaning the condenser unit
Periodically (every month) remove the condenser unit
and clean any build up of fluff from between the plates
by rinsing it under the tap with cold water.
This should be done with cold water from the rear of
the condenser.
The filter is found in front of the dryer trim (see diagram).
Removing the filter:
1. Pull the plastic grip of the filter upwards (see diagram).
2. Open the filter and clean the lint from
the inside.
Removing the condenser:
1. Unplug the dryer and open the door.
2. Pull open the condenser cover (see diagram).
Release the three catches by turning 90˚ counter-
clockwise then pull on the grip and remove from
the dryer.
3. Replace it correctly. Ensure the filter
is fully located flush into the tumble
dryer trim.
4. Remove any lint that has built up on the inside of the
door and around the door seal.
! Do not use the dryer without replacing the filter.
3. Clean the surface of the seals and replace, making
sure that the catches have been secured.
Cleaning the dryer
Check the drum after each cycle
●
External parts in metal or plastic and rubber parts
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
can be cleaned with a damp cloth.
Periodically (every 6 months) vacuum the front air
●
intake grille, to remove any build up of fluff, lint or
dust. Also to remove accumulation of fluff from the
front of the condenser and filter areas, clean
occasionally with a vacuum cleaner.
Empty the water container after each
cycle
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
Pull the container out of the dryer and remove either
the small or large cap and empty it into a sink or other
suitable drain. Refit the cap and replace the container
securely.
! Always check and empty the container before you
start a new drying programme.
Tap
Water container
Rear
Front
Filter
Condenser unit
Condenser unit
Air intake
Condenser cover
Catches
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
GB
Problem:
Possible causes / Solution:
●
The tumble dryer won’t start.
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
●
●
●
directly into the socket.
The door is not closed securely?
The programme has not been set properly (see Start and Programmes).
The Start/Pause button has not been pressed (see Start and Programmes).
●
●
●
●
Drying cycle will not begin.
Its taking a long time to dry.
You have set a delayed time (see Start and Programmes).
●
The filter has not been cleaned (see Maintenance).
The water container needs emptying? The empty water message is
●
displayed? (see Maintenance).
The condenser needs cleaning? (see Maintenance).
The temperature setting is not ideal for the type of fabric you are drying
●
●
(see Start and Programmes, and see Laundry).
The correct drying time has not been selected for the load (see Laundry).
The air intake grille is obstructed (see Installation, and see
●
●
Maintenance).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
●
●
●
Empty water message is
displayed but the dryer has
only been running for a short
period.
The water container was probably not emptied at the start of the
programme. Do not wait for the empty water signal, always check and
empty the container before starting a new drying programme (see
Maintenance).
●
Empty water message is
displayed and the water
container is not full.
This is normal, the: END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
message is shown as a reminder to empty the container (see The Display
and Start and Programmes).
Programme finishes and
clothes are damper than
expected.
! For safety the dryer has a maximum programme time of 4 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
●
The display shows a fault
code F followed by one or two
numbers.
If the display shows a fault:
- Turn off and remove the plug. Clean the filter and the condenser
(see Maintenance). Then replace the plug, turn on and start another
programme. If a fault is then displayed note down the code and
contact the Service Centre (see Service).
●
The display briefly shows
DEMO ON every 6 seconds.
The dryer is in ‘Demo’ mode. Press and hold both the On/Off and
Start/Pause buttons for 3 seconds. The display will show DEMO OFF for
3 seconds and then the dryer will resume normal operation.
●
The lights on the dryer control
panel are off although the
dryer is switched on.
The dryer has gone into standby mode to save power. This occurs if you
have had a power cut or leave your dryer either without starting a
programme or after your drying programme has finished.
- Press and hold the On/Off button and the lights will come on.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Before calling the Service Centre:
Spare Parts
GB
●
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service Centre
closest to you.
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
●
What to tell the Service Centre:
Call an authorised technician if you experience problems
while using the machine.
●
name, address and post code.
telephone number.
the type of problem.
the date of purchase.
●
●
●
●
the appliance model (Mod.).
●
the serial number (S/N).
This information can be found on the data label inside
the door of the machine.
Recycling and Disposal Information
As part of our continued commitment to helping
the environment, we reserve the right to use
quality recycled components to keep down customer
costs and minimise material wastage.
Disposal of old electrical appliances
The European Directive 2012/19/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
●
Disposing of the packaging material: follow local
regulations, so the packaging can be recycled.
To minimise risk of injury to children, remove the
●
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
This appliance conforms to the following EC Directives:
- 2006/95/EC (Low Voltage Equipment)
- 2004/108/EC (Electromagnetic Compatibility)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturers’ guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be
defective because of either workmanship or materials, we will, at our discretion, either
repair or replace the appliance at no cost to you.
The guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
- The appliance is only used on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled or otherwise
interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our
property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a
result of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN
COMMERCIAL OR NON-DOMESTIC PREMISES.
Non-Domestic Usage Policy:
Indesit Company manufactures appliances for domestic use only. We understand that in
some cases our appliances are used in commercial and/or non-domestic situations. We
still provide a full 12 month manufacturers’ guarantee, provided the appliance has not been:
Accidentally damaged - Damage that occurs suddenly as a result of an unexpected and
non-deliberate external action.
Maliciously damaged - The deliberate and intentional damage to the product.
Subjected to misuse - Incorrect or careless or improper use.
Subjected to overuse - Excessive usage versus that expected of a domestically situated
appliance.
5 Year Parts Guarantee
Hotpoint also offers you a FREE 5 year parts guarantee. This additional guarantee is
conditional on you registering your appliance with us and the parts being fitted by one
of our authorised engineers. There will be a charge for our engineer’s time.
To activate the extra parts warranty on your appliance, simply call our free phone registration line on
0800 519 2102 (Republic of Ireland 1800 844 347)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
195101293. 01 N
02/2013 - LION fpg . Four Ashes, Wolverhampton
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on
UK: 08448 226 226
Republic of Ireland: 01 230 0233
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint
Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance,
or, where necessary, to arrange for an engineer to call.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its
working life than us - the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled
telephone advisors and 1100 fully qualified engineers on call to ensure you receive
fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number
Serial number
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that
protect and hygienically clean your appliance to keep it looking good and functioning
efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership.
To activate your FREE 5 year parts guarantee you must register your appliance with us.
Free phone UK: 0800 519 2102
Republic of Ireland: 1800 844 347
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
Indesit Company, Unit 49 Airways Industrial Estate, Dublin 17
Download from Www.Somanuals.com. All Manuals Search And Download.
|