Honeywell Home Security System K5305 1V5 User Manual

Page 2-8 and 8-1 Has been edited by Tech Support. If you have any

questions call 1.800.645.7492

ADEMCO VISTA SERIES

VISTA-20P / VISTA-20PSIA

VISTA-15P / VISTA-15PSIA

Security Systems

Installation and Setup Guide

K5305-1V5 10/04 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

Table Of Contents

Features and Installation Highlights............................................................................................................1-1

Capabilities and Functions................................................................................................................................................1-1

Compatible Devices ...........................................................................................................................................................1-2

Important Installation Highlights (Installer Please Read) .............................................................................................1-2

Mounting and Wiring the Control .................................................................................................................2-1

Installing the Control Cabinet and PC Board..................................................................................................................2-1

Cabinet and Lock .........................................................................................................................................................2-1

Mounting the PC Board Alone (no RF Receiver)........................................................................................................2-1

Mounting Board with RF Receiver..............................................................................................................................2-1

AUXILIARY DEVICE CURRENT DRAW WORKSHEET..............................................................................2-2

AC Power, Battery, and Ground Connections..................................................................................................................2-3

1321 Transformer.........................................................................................................................................................2-3

1361X10 Transformer..................................................................................................................................................2-3

Battery Connections.....................................................................................................................................................2-3

Battery Saver Feature .................................................................................................................................................2-3

Earth Ground ...............................................................................................................................................................2-3

Sounder (Bell) Connections...............................................................................................................................................2-4

Basic Connections ........................................................................................................................................................2-4

Supervised output........................................................................................................................................................2-4

Connecting the Keypads and Other Addressable Devices...............................................................................................2-4

Connections ..................................................................................................................................................................2-4

Supplementary Power (optional).................................................................................................................................2-4

Keypad Notes ...............................................................................................................................................................2-5

Long Range Radio Connections...................................................................................................................................2-5

Table of Device Addresses .................................................................................................................................................2-5

Hardwire Zones and Zone Expansion...............................................................................................................................2-6

Hardwire Zones............................................................................................................................................................2-6

Double-Balanced Zones................................................................................................................................................2-6

Zone Doubling ..............................................................................................................................................................2-6

Smoke Detectors...........................................................................................................................................................2-6

Smoke Detector Notes..................................................................................................................................................2-7

4219/4229 Expansion Zones ........................................................................................................................................2-7

Installing the RF Receiver and Wireless Transmitter Zones ..........................................................................................2-8

Compatible Receivers...................................................................................................................................................2-8

Receiver Connections...................................................................................................................................................2-8

RF Receiver Notes........................................................................................................................................................2-8

Installing a 5800TM Module .......................................................................................................................................2-9

Installing the Transmitters.........................................................................................................................................2-9

Transmitter Battery Life.............................................................................................................................................2-9

Installing a Keyswitch.....................................................................................................................................................2-10

Keyswitch Connections..............................................................................................................................................2-10

Keyswitch Notes.........................................................................................................................................................2-10

Connecting Relay Modules, Powerline Carrier Devices and Output Triggers..............................................................2-11

4204/4229 Relay Modules ..........................................................................................................................................2-11

Powerline Carrier Devices.........................................................................................................................................2-11

On-Board Triggers .....................................................................................................................................................2-12

Phone Line/Phone Module, and Audio Alarm Verification (AAV) Connections............................................................2-13

Phone Line..................................................................................................................................................................2-13

4285/4286 Phone Module...........................................................................................................................................2-13

Phone Module Problems ............................................................................................................................................2-13

Audio Alarm Verification Connections......................................................................................................................2-14

Programming Overview...................................................................................................................................3-1

About Programming ..........................................................................................................................................................3-1

Mechanics of Programming...............................................................................................................................................3-1

Data Field Programming Procedures..........................................................................................................................3-1

Interactive Mode Programming (∗56, *57, ∗58, ∗79, ∗80, ∗81, ∗82)...........................................................................3-2

Loading Factory Defaults/Initializing for Download..................................................................................................3-2

Exiting the Programming Mode..................................................................................................................................3-2

Zone Type Definitions........................................................................................................................................................3-2

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

Table Of Contents (continued)

Data Field Programming .................................................................................................................................4-1

About Data Field Programming........................................................................................................................................4-1

∗

System Setup Fields ( 20 – ∗29) .......................................................................................................................................4-1

Zone Sounds & Timing (∗31–∗39) .....................................................................................................................................4-1

∗

Dialer Programming ( 40 – 50).......................................................................................................................................4-2

System Status Report Codes.............................................................................................................................................4-4

Miscellaneous System Fields ............................................................................................................................................4-5

Pager Programming Fields................................................................................................................................................4-7

Miscellaneous System Fields ............................................................................................................................................4-8

Configurable Zone Type Fields .........................................................................................................................................4-9

Touch Screen Device (AUI) Enable.................................................................................................................................4-11

Keypad Programming Fields...........................................................................................................................................4-11

Menu Mode Programming ...............................................................................................................................5-1

Zones and Partitions..........................................................................................................................................................5-1

About Zone Programming (∗56 and ∗58 Menu Modes) ....................................................................................................5-1

✱56 Zone Programming Procedure ...................................................................................................................................5-1

Completing Zone Programming ........................................................................................................................................5-4

∗58 Expert Programming Mode Procedures.....................................................................................................................5-4

Wireless Key Programming Templates ............................................................................................................................5-6

About Output Device Programming (*79/*80 Menu Mode).............................................................................................5-8

Programming Output Devices...........................................................................................................................................5-8

*79 Menu Mode: Output Device Mapping ........................................................................................................................5-8

*80 Menu Mode: Defining Output Functions .................................................................................................................5-10

About Zone Lists (*81 Menu Mode) ................................................................................................................................5-12

Zone List Programming...................................................................................................................................................5-12

About Function Keys (*57 Menu Mode)..........................................................................................................................5-13

Programming Function Keys ..........................................................................................................................................5-13

About Descriptor Programming (*82 Menu Mode) ........................................................................................................5-14

Programming Zone Descriptors (Menu Mode ∗82).........................................................................................................5-14

Adding Custom Words (will not be annunciated by 4285/4286 Phone Module) ...........................................................5-15

Programming Installer and User Schedules ..................................................................................................................5-17

System Communication and Operation .......................................................................................................6-1

Panel Communication with Central Station ....................................................................................................................6-1

Report Code Formats.........................................................................................................................................................6-1

Ademco Contact ID .........................................................................................................................................................6-3

System Security Codes ......................................................................................................................................................6-4

Panic Keys......................................................................................................................................................................6-6

Setting the Real-Time Clock .............................................................................................................................................6-6

Various System Trouble Displays.....................................................................................................................................6-7

Testing the System.............................................................................................................................................7-1

About Test Procedures.......................................................................................................................................................7-1

System Test........................................................................................................................................................................7-1

Checking Transmitter Enrollment (Sniffer Mode)...........................................................................................................7-1

Go/No Go Test Mode..........................................................................................................................................................7-2

Dialer Communication Test and Periodic Test Reports...................................................................................................7-2

Automatic Standby Battery Tests.....................................................................................................................................7-2

Specifications & Accessories...........................................................................................................................8-1

Security Control.................................................................................................................................................................8-1

Compatible Devices ...........................................................................................................................................................8-1

5800 Series Transmitter Input Loop Identification .........................................................................................................8-3

Regulatory Agency Statements ......................................................................................................................9-1

Limitations and Warranty .............................................................................................................................10-7

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Features and Installation Highlights

This manual applies to the following Honeywell security systems:

ADEMCO VISTA-20P/ADEMCO VISTA-20PSIA/ADEMCO VISTA-20PCN (collectively referred to as

VISTA-20P series), ADEMCO VISTA-15P/ADEMCO VISTA-15PSIA/ADEMCO VISTA-15PCN

(collectively referred to as VISTA-15P series)

Features and procedures apply to all, except where differences are noted.

SIA Installations: The VISTA-20PSIA and VISTA-15PSIA are certified SIA-compliant controls that

meet SIA specifications for False Alarm Reduction. The other controls described in this manual are

not certified as SIA compliant, but can be programmed for False Alarm Reduction. To program for

False Alarm Reduction, follow the SIA Guidelines noted in the applicable programming fields.

NOTE: Throughout this manual, device model numbers are ADEMCO model numbers

unless otherwise noted.

Capabilities and Functions

Feature/Function ADEMCO VISTA-20P Series

ADEMCO VISTA-15P Series

Partitions

VISTA-15P is not a partitioned system.

• 2 partitions, can protect two independent

areas

• Common zone option allows either

partition to arm, while leaving a common

area (ex. lobby or foyer) disarmed for

access into the other partition.

Zones

Up to 48 protection zones plus 16 keyfob

zones (zones 49-64) for total of 64 zones:

• 8 basic hardwired zones (zones 1-8) with

optional zone-doubling feature

• Up to 40 additional wired zones (zones 9-

48) using up to 5 4219/4229 modules

• Up to 40 wireless transmitter zones (5800

series; zones 9-48)

Up to 32 zones plus 8 keyfob zones (zones

49-56) for total of 40 zones:

• 6 basic hardwired zones (zone 1-6)

• Up to 16 additional wired zones (zones 9-

24) using up to 2 4219/4229 modules

• Up to 26 wireless transmitter zones

(5800 series; zones 9-34)

• Up to 2 configurable zone types

• Up to 4 configurable zone types

Up to 48 Security Codes, with separate

authority levels and partition access

Dedicated keys can arm the system.

Up to 32; can control devices and/or auto-

arm/disarm

Security Codes

Up to 32 Security Codes, with separate

authority levels

Dedicated keys can arm the system.

Up to 8; can control devices and/or auto-

arm/disarm

One-button arming

Schedules

Keypad macros

Paging

Up to 4; activated by wired keypads

Up to 4 pagers; certain system conditions

can report to pagers; can use a dedicated

key on keypads to send a signal to a pager

100 events; log display is done via Ademco

Compass Downloader software or

installer/master code at Keypad

Up to 2; activated by wired keypads

Up to 2 pagers; certain system conditions

can report to pagers; can use a dedicated

key on keypads to send a signal to a pager

50 events; log display is done via Ademco

Compass Downloader software or

installer/master code at Keypad

Event Logging

Zone descriptors

Bell supervision

Can assign for all zones (for alpha display keypads and/or 4285/4286 Phone Module).

Optional, detects external sounder wiring short or open; causes a trouble condition,

keypad display, and sends a report to the central monitoring station, if enabled.

Optional, for wireless systems detects a condition that may impede proper RF reception

(i.e., jamming or other RF interference); causes keypad display, and sends a report to the

central monitoring station (if trouble reporting is enabled).

RF jam detection

Telephone Line

Monitoring

Built-in option can monitor the telephone line voltage and can cause a local display, or a

display and trouble/alarm sound

Downloading

Via an IBM compatible computer, Compass downloading software, and a compatible

HAYES or CIA modem specified by Ademco.

1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Compatible Devices

Device

VISTA-20P VISTA-15P

Notes

Addressable Keypads

6150 Fixed-Word Keypad, 6160 Alpha Keypad, 6150V

Fixed-Word Display Voice Keypad, 6160V Alpha

Display Voice Keypad, 6150RF Keypad/Transceiver

Touch Screen (AUI) devices are in addition to the 8

addressable keypads. E.g., Symphony, 6270

Touch Screen (AUI)

Devices

4219, 4229 Zone

Expander Modules

Up to 5 for

up to 40

exp. zones

Up to 2 for

up to 16

exp. zones

Zone numbers are predefined according to the device

addresses used. See Expander Module Addresses table

in Wiring section and set addresses accordingly.

5800 Series Wireless

Up to 40 RF Up to 26 RF Uses 5881/5883 Series Receivers/Transceivers.

zones

Output relays and/or

Powerline Carrier

Devices (X-10 type)

On-Board Triggers

Output functions

4285/4286 Phone

Module

Up to 16

Up to 8

Use any combination of 4204, 4229 and or Powerline

Carrier Devices.

Map output devices via *79 Menu mode.

Can be used to reset 4-smoke detectors.

Up to 48

Partition 1

only

Up to 24

yes

Program output functions via *80 Menu mode.

Provides access to the system via on premises or off-

premises phones for arming, disarming, etc., plus

control of relay outputs and Powerline Carrier devices.

Use ADEMCO UVS or Eagle Model 1250; can be used

in conjunction with an output trigger to permit voice

dialog between an operator at the central station and

a person at the premises.

Audio Alarm

Verification

Using AAV

module

Using AAV

module

Alarm output

12VDC, 2

Can drive the compatible sounders; steady output for

AMP output AMP output burglary/panic, or temporal pulse (3 pulses – pause –

3 pulses – pause – 3 pulses. . .) for fire. Uses current

limiting circuitry for protection.

Auxiliary Power Output

Backup Battery

See note.

See note

See note.

12VDC, 600 mA maximum; uses fuse for protection.

Rechargeable (sealed lead-acid type) 12VDC, 4AH

minimum.

Long Range Radio

AC Power Supply

See note.

Primary telephone number messages can be reported

via ECP connection to various Long Range Radios

(check compatibility/availability of specific models)

Plug-in 120VAC transformer, ADEMCO 1321

(1321CN in Canada) or, if using Powerline Carrier

devices, ADEMCO 1361X10 Transformer Module

NOTE: All devices and accessories used in a Canadian installation must be Listed for use in Canada.

Important Installation Highlights (Installer Please Read)

• This system uses addressable keypads and Zone Expander Modules (see Table of Addresses in

Section 2. Mounting and Wiring – Wiring the Keypads and Other Addressable Devices).

• Keypads must be set for addresses 16-23 (first keypad is address 16, which is different from

previous controls) and programmed in data fields *190-*196.

• Zone Expander Modules must be set for specific addresses (07-11), based on the zone numbers used.

• 4204 Relay Modules must be set for specific addresses (12-15).

• This control will not power-up unless AC power is connected (will not power-up on battery alone).

However, once the system is powered up, it will operate on battery power in the event of AC loss.

• Relays have two programming menu modes: Use *79 Menu mode to map module addresses and

device (output) numbers. Use *80 Menu mode to define the output functions.

• This system supports programmable function keys. Use *57 Menu mode to define the function

keys.

• This system provides various paging features. Refer to the Programming Overview section for a

summary on pager programming.

1-2

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Mounting and Wiring the Control

Installing the Control Cabinet and PC Board

PUSH

ON LOCK

UNTIL IT

IS SEATED

SECURELY

Cabinet and Lock

1. Mount the control cabinet to a

sturdy wall in a clean, dry area,

which is not readily accessible to

the general public, using fasteners

or anchors (not supplied) with the

four cabinet mounting holes.

CHECK

SNAP

TAB

POSITION

LOCKED

PUSH

SNAP

TAB

2. Remove cabinet door, then remove

the lock knockout from the door.

Insert the key into the lock.

UNLOCKED

CABINET DOOR

BOTTOM

STEP 1

STEP 2

Figure 1. Installing the Cabinet Lock

3. Position the lock in the hole, making certain that the latch will make contact with the

latch bracket when the door is closed. When correctly positioned, push the lock until

the snap tabs hold it securely.

The cabinet can be secured without a lock by using 2 screws in the cover's edge.

Before installing the cabinet's contents, remove the metal cabinet knockouts required for

wiring entry. Do not remove the knockouts after the circuit board has been installed.

1. Hang two short mounting clips (provided) on the raised cabinet tabs (see Detail B).

2. a. Insert the top of the circuit board into the slots at the top of the cabinet. Make sure

that the board rests on the correct row (see Detail A).

Mounting the PC Board

Alone (no RF Receiver)

b. Swing the base of the board into the mounting clips and secure the board to the

cabinet with the accompanying screws (see Detail B).

CIRCUIT

CABINET

BOARD

CIRCUIT

BOARD

CABINET

DETAIL B

SIDE VIEW

OF MOUNTING

CLIPS

DETAIL A

SIDE VIEW

OF BOARD

SUPPORTING

SLOTS

MOUNTING-001-V0

Figure 2. Mounting the PC Board

• Do not mount the cabinet on or near metal objects. This will decrease RF range and/or

block RF transmissions from wireless transmitters.

Mounting Board with RF

Receiver

• Do not locate the cabinet in an area of high RF interference (revealed by frequent or

prolonged lighting of the LED in the receiver (random flicker is OK)

1. a. Remove the receiver board from its case, then insert the top of the board into the

slots at the top of the cabinet, as shown in Detail A in Figure 3 on the next page.

Make sure that the board rests on the correct row of tabs.

b. Swing the base of the board into the mounting clips and secure it to the cabinet

with the accompanying screws.

c. Insert the top of the control's board into the slot in the clips and position two clips

at the lower edge of the board.

d.Swing this board into place and secure it with two additional screws.

2. Insert grounding lugs (supplied with the receiver) through the top of the cabinet into

the left-hand terminals of the antenna blocks (at the upper edge of the receiver board)

and secure them to the cabinet top with the screws provided (see Detail B).

3. Insert the receiver's antennas through the top of the cabinet, into the blocks' right-

hand terminals, and tighten the screws.

2-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

CABINET

BOARD

SUPPORTING

SLOTS

RECEIVER CIRCUIT BOARD

CIRCUIT

BOARD

MOUNTING

CLIP

CONTROL

CIRCUIT

BOARD

DETAIL A

SIDE VIEW

OF BOARD -

SUPPORTING SLOTS

MOUNTING

CLIP

INSTALLATION WITH RECEIVER CIRCUIT BOARD

ANTENNA

(2)

SCREW

(2)

GROUNDING

LUG

(2)

WHITE

MOUNTING

CLIP

BLACK

MOUNTING

CLIP

RED

MOUNTING

CLIP

NOTE

A COMBINATION OF THESE MOUNTING CLIPS HAS BEEN

INCLUDED IN YOUR INSTALLATION KIT.

ANTENNA

MOUNT

(2 PLACES)

USE THE APPROPRIATE CLIPS FOR MOUNTING.

DETAIL B

ANTENNA AND GROUNDING

LUG INSTALLATION

IF NO RF RECEIVER IS USED, MOUNT THE PC BOARD USING

EITHER THE WHITE OR BLACK CLIPS, WHICHEVER ARE

INCLUDED IN THE CONTROL PANEL'S HARDWARE KIT.

pc_mount-001-V1

Figure 3. Mounting the PC Board and RF Receiver

AUXILIARY DEVICE CURRENT DRAW WORKSHEET

DEVICE

6150 Fixed-Word Keypad

6160 Alpha Keypad

CURRENT

40mA/70mA**

40mA/150mA**

60mA/160mA**

60mA/190mA**

150mA/400mA**

180mA/280mA**

60mA

No. UNITS

TOTAL CURRENT

6150V Fixed-Word Display Voice Keypad

6160V Alpha Display Voice Keypad

8132/8142 Series AUI (Symphony)

6270 Touch Screen Keypad

5881/5882 RF Receiver

5883 Transceiver

80mA

4219 Zone Expander

30mA

4204 Relay Unit

‡

15/180mA

4229 Zone Expander/Relay Unit

30/100mA

160mA

300mA

4285 Phone Module

4286 Phone Module

†

(Current available from Aux. terminals = 600 mA max.)

TOTAL =

*If using hardwire devices such as PIRs, refer to the specifications for that particular unit's current draw.

** Values are for standby/alarm; alarm for keypads means armed with backlighting on and sounder on

†In UL installations, maximum current draw from the Auxiliary Output and the Alarm Output combined must not exceed 600 mA (500 mA max from Aux. Output).

‡Values are for relays OFF/relays ON.

CALIFORNIA STATE FIRE MARSHALL (CSFM) AND UL RESIDENTIAL FIRE

24-HOUR BATTERY BACKUP REQUIREMENTS

The California State Fire Marshal and UL have regulations which require that all residential fire alarm control panels must be

provided with a backup battery which has sufficient capacity to operate the panel and its attached peripheral devices for 24 hours in

the intended standby condition, followed by at least 4 minutes in the intended fire alarm signaling condition. This control panel can

meet these requirements without using a supplementary power supply, provided that the panel’s auxiliary power and bell output

currents are limited as indicated below.

OUTPUT LIMITATIONS AND CORRESPONDING REQUIRED BATTERIES

OUTPUT CURRENT LIMITATIONS

Output Current Total Maximum Auxiliary Current

BATTERY INFORMATION

Battery Capacity

To Use (Amp/Hrs)

Recommended Battery

(Yuasa Model No.)

NP4-12 (or ADEMCO 467)

NP7-12

600mA maximum total of

auxiliary power plus bell

output currents

45mA

160mA

200mA

425mA

500mA

4AH

7AH

8AH

NP4-12 (two) ‡

NP7-12 (two) ‡

NPG18-12

14AH

17.2AH

‡ NOTE: Use two batteries, connected in parallel. Obtain an Ademco Battery Harness Kit SA5140-1. (Both batteries will fit inside the cabinet.)

2-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting and Wiring the Control

AC Power, Battery, and Ground Connections

1321 Transformer

Connect the 1321 Transformer (1321CN in

Canada) to terminals 1 and 2 on the

control board. See Wire Run Chart for

wire size to use.

Wire Run Chart

Distance from control Wire Size

Up to 50 feet

50–100 feet

100-250 feet

# 20

# 18

# 16

•

Use caution when wiring the

transformer to the control to guard

against blowing the transformer fuse

(the fuse is non-replaceable).

TERMINALS

1 AND 2

•

Wiring to the AC transformer must not exceed 250 feet using 16 gauge wire. The

voltage reading between terminals 1 and 2 of the control must not fall below 16.5VAC

or an “AC LOSS” message will be displayed.

Do not plug the transformer into the AC outlet until all wiring connections to the

control are complete. As a safety precaution, always power down the control when

making such connections.

8-PIN TRIGGER CONNECTOR

1361X10 Transformer

(required if using

Powerline Carrier devices)

1. Splice one end of a 3-conductor cable

to the wire ends of the SA4120XM-1

Cable.

2. Connect the SA4120XM-1 cable plug

to the 8-pin connector on the control

(see the Summary of Connections

diagram for location of the 8-pin

connector).

1361X10 TRANSFORMER

SYNC COM DATA

8-PIN

SA412OXM

CABLE

CONNECTOR

3. Connect the other end of the

3-conductor cable to the 1361X10

Transformer, as shown in Figure 4.

Canadian Installations: See

Powerline Carrier Device section for

connections to the PSC04 X-10 Interface

and trigger pins.

CONTROL

BOARD

TERMS.

TERMINALS

1 AND 2

Figure 4. 1361X10 Transformer Connections

Battery Connections

1. Place the 12-volt backup battery in the cabinet.

2. After all connections to the control are completed and AC power has been applied,

connect the red and black flying leads on the control board to the battery. Do not

attach these leads to the battery terminals until all connections are completed.

BLACK

RED

L ^{For UL installations and Residential fire installations, refer to the chart on page 2-2}

at left for the correct battery size required to meet the mandatory standby time.

CONNECT

FLYING LEADS

AFTER AC POWER

IS APPLIED

Battery Saver Feature

Earth Ground

The battery will disconnect from the system after its voltage decreases below 9VDC.

This assists the control panel in recharging the battery when AC is restored.

IMPORTANT: The panel will not power up initially on battery power only. You must

plug the transformer in first, and then connect the battery.

• This product has been designed and laboratory-tested to ensure its resistance to

damage from generally expected levels of lightning and electrical discharge, and does

not normally require an earth ground.

• If an earth ground is desired for additional protection in areas of severe electrical

activity, terminal 25 on the control board, or the cabinet, may be used as the ground

connection point. The following are examples of good earth grounds available at most

installations.

CONNECT

PROPER

EARTH

GROUND

ARD

OL BO

CONTR

DESIRED

Metal Cold Water Pipe: Use a non-corrosive metal strap (copper is recommended) firmly

secured to the pipe to which the ground lead is electrically connected and secured.

AC Power Outlet Ground: Available from 3-prong, 120VAC power outlets only. To test

the integrity of the ground terminal, use a 3-wire circuit tester with neon lamp

indicators, such as the UL Listed Ideal Model 61-035, or equivalent, available at most

electrical supply stores.

2-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Sounder (Bell) Connections

Basic Connections

Make sounder connections to alarm output terminals 3 (+) and 4 (–).

• The 12VDC sounder output activates when an alarm occurs.

• Total current drawn from this output cannot exceed 2 amps (going beyond 2 amps will

overload the power supply, or may cause the electronic circuit protecting the sounder

output to trip).

• You must install a battery, since the battery supplies this current.

Supervised output

ALARM OUTPUT

10.5 - 13.5 VDC

2A MAX.

1. Cut the red Bell Supervision Jumper located above terminals 2 and 3 on the PC board.

2. Connect a 2k ohm resistor across the terminals of the last sounder. See Figure 5.

This control complies with NFPA requirements for temporal pulse sounding of fire notification

appliances. Temporal pulse sounding for a fire alarm consists of: 3 pulses – pause – 3 pulses –

pause – 3 pulses–etc..

TERMINALS ON

CONTROL BOARD

EXTERNAL ALARM

SOUNDER

• Use only UL Listed sounding devices for

UL installations.

• Bell supervision is required for fire alarm

installations.

2000

OHM

EOL

ALARM

OUTPUT

TERMINALS

OBSERVE

POLARITY

RESISTOR

• The total current drawn from the alarm

output and the auxiliary power output,

combined, cannot exceed 600 mA. In

addition, the sounding device must be a

UL Listed audible signal appliance rated

to operate in a 10.2-13.8 VDC voltage

range, and must be mounted indoors.

IF BELL SUPERVISION IS ENABLED

(RED JUMPER ON CONTROL BOARD IS CUT)

CONNECT A 2000 OHM RESISTOR ACROSS

THE EXTERNAL SOUNDER AS SHOWN BY

THE DOTTED LINE.

CUT RED JUMPER ON CONTROL

BOARD TO ENABLE BELL

(SOUNDER) SUPERVISION.

DO NOT CONNECT THE RESISTOR AT THE

ALARM OUTPUT TERMINALS THEMSELVES!

Figure 5. Sounder Wiring (Supervised)

Connecting the Keypads and Other Addressable Devices

Connections

Connect keypads and other addressable devices (4204, 4219, 4229, 4286, 5881, LRR,

etc.) to the control’s keypad terminals as shown on the Summary of Connections

diagram. The system supports up to 8 keypads, which can be assigned to partitions in

any combination (see program fields *190-*196).

6 IN

7 OUT

Determine wire size using the Wire Run Chart on the following page. For single 4-wire

runs, determine the current drawn by all units, then refer to the Wiring Run chart to

determine the maximum length that can be safely used for each wire size.

Supplementary Power

(optional)

Use supplementary power if the

control’s aux. power load for all

devices exceeds 600mA (suggested

power supply: AD12612). Connect

as shown in Figure 6. Be sure to

connect the negative (–) terminal

on the power supply unit to

SUPPLEMENTARY

CONTROL TERMINAL STRIP

POWER SUPPLY

–

AUX. AUX. DATA DATA

IN OUT

–

Use a UL Listed,

battery-backed supply for

UL installations. The battery

supplies power to these

keypads in case of AC

power loss.

The battery-backed power

supply should have enough

power to supply the

keypads with the UL

required minimum standby

power time.

terminal 4 (AUX –) on the control.

IMPORTANT:

MAKE THESE

CONNECTIONS

DIRECTLY TO

SCREW

IMPORTANT: Keypads

powered from supplies that do

not have a backup battery will

not function if AC power is lost.

Make sure to power at least one

keypad in each partition from

the control’s auxiliary power

output.

TERMINALS AS

SHOWN.

Figure 6. Using a Supplementary Power Supply

2-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting and Wiring the Control

Keypad Notes

Set device addresses. Refer to the instructions included with the devices and set each

address according to the Table of Devices Addresses.

See Keypad Programming Fields (fields *190-*196) in Section 4. Data Field

Programming for details on enabling keypad addresses, assigning keypad partitions

and selecting keypad sounding options.

ARMED

READY

ANT

IMPORTANT: Each keypad must be assigned a unique, predefined address, from 16 to

23. The first keypad is address 16 (default = partition 1, all sounds enabled).

TOUCH SCREEN KEYPAD (AUI) NOTES:

• Use of up to 2 AUI devices (e.g., 6270, Symphony) is independent from standard

keypads and does not affect the number of standard keypads the system can support.

• AUI devices must be set for either address 1 or address 2, depending on which unit is

enabled in field *189.

• To ensure proper AUI device operation, connect only to controls having microprocessor

version 3.0 or higher, and use AUI devices with the following rev levels: 6270 series

use version 1.0.9 or higher; 8132/8142 (Symphony) series use version 1.1.175 or higher.

Connect the data in/data out terminals and voltage input terminals of the Long Range

Radio to the control's keypad connection points.

Long Range Radio

Connections

Set the radio’s address to “03” following the instructions provided with the radio.

• Use compatible Long Range Radios (e.g., 7720PLUS, 7820, 7835C, or 7845C).

Wire Run Chart For Devices* Drawing Aux Power From The Control (12V+ & 12V–)

TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN

Wire

Size

#22

#20

#18

#16

50 mA or less

900 ft (274m)

1400 ft (427m)

1500 ft (457m)

100 mA

300 mA

500 mA

600 mA

450 ft (137m)

700 ft (213m)

1100 ft (335m)

1500 ft (457m)

150 ft (46m)

240 ft (73m)

350 ft (107m)

550 ft (168m)

90 ft (27m)

140 ft (43m)

220 ft (67m)

350 ft (107m)

75 ft (23m)

120 ft (37m)

170 ft (52m)

270 ft (82m)

* Includes Keypads, RF Receivers, Zone Expander/Relay Units, 4285/4286 Phone Module, and Long Range Radio.

Maximum wire lengths for any device that is homerun to the control can also be determined from the Wiring Run Chart, based on the

current draw of that device alone.

The length of all wire runs for both partitions combined must not exceed 1500 feet (457m) when unshielded quad conductor cable is used

(750 feet if shielded cable is used). This restriction is due to the capacitive effect on the data lines when quad cable is used.

Table of Device Addresses

Reports as^††

This Device

Uses Address

Enabled By…

RF Receiver

AUI 1

AUI 2

100

101

102

103

104

*56 zone programming: input device type entry

automatic if AUI enable field *189 enabled for AUI 1

automatic if AUI enable field *189 enabled for AUI 2

automatic if output to long range radio field *29 enabled

automatic if phone module access code field *28 enabled

*56 zone programming: input device type, entry 2, then:

automatic if zone no. 9-16 set as AW type or relay assigned

automatic if zone no. 17-24 set as AW type or relay assigned

automatic if zone no. 25-32 set as AW type or relay assigned

automatic if zone no. 33-40 set as AW type or relay assigned

automatic if zone no. 41-48 set as AW type or relay assigned

Long Range Radio

4286 Voice Module

Zone Expanders (4219/4229):

module 1 (for zones 09 - 16)

module 2 (for zones 17 - 24)

module 3 (for zones 25 - 32)

module 4 zones 33 - 40

module 5 zones 41 - 48

07**

107

108

109

110

111

09^†

10^†

11^†

Relay Modules (4204):

module 1

module 2

module 3

module 4

*79 output device programming: device address prompt:

entered at device address prompt

112

113

114

115

14^†

15^†

Keypads:

keypad 1

keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

5800TM Module

data field programming as listed below:

always enabled for partition 1, all sounds enabled.

data field *190

data field *191

data field *192

data field *193

data field *194

data field *195

data field *196

n/a

automatic

** address 07 not available if zone-doubling enabled

† 4219/4229 addresses 9-11 and 4204 addresses 14-15 apply to the VISTA-20P.

†† Addressable devices are identified by “1” plus the device address when reporting. Enter a report code for zone 91 to enable

addressable device reporting (default = reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification

keypad display options.

2-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Hardwire Zones and Zone Expansion

Hardwire Zones

Normally Open Zones/ N.O. EOLR Zones

1. Connect open circuit devices in parallel across the loop; for EOLR zones, connect the

EOLR across the loop wires at the last device.

2. Enable normally open/EOLR zones using Zone Programming mode, “Hardwire Type”

prompt.

Normally Closed Zones/ N.C. EOLR Zones

1. Connect closed circuit devices in series in the high (+) side of the loop; for EOLR

zones, connect the EOLR in series following the last device.

2. Enable normally closed/EOLR zones using Zone Programming mode, “Hardwire

Type” prompt.

End of Line Resistor (EOLR) Notes

• If the EOLR is not at the end of the loop, the zone is not properly supervised and the

system may not respond to an “open” on the zone.

• Zone 1 is intended for EOLR only.

For UL commercial burglar alarm installations, use EOLR zones.

Double-Balanced Zones

(V20P only)

Connect as shown below (resistor provided

for one device).

IMPORTANT: Double-balanced zones

provide zone tamper protection, and should

be used as burglary zones only.

Do not use double-balanced zones as fire

zones.

TAMPER

CONTACTS

TAMPER

CONTACTS

ZONE 3

ZONE 4

Fig. 7. Typical Double Balanced Zones

Zone Doubling

(V20P only)

This feature provides two hardwired

normally closed zones for each standard

hardwired zone connected to the control’s

terminals (but does not increase the total

number of zones supported by the control). If

enabled (Zone Programming mode,

“Hardwire Type” prompt, option “3”),

hardwire zones are automatically paired as

shown in the table. Connect as shown below

(resistors provided).

ZONE 2

ZONE 10

6.2k

Fig. 8. Typical Zone Doubling Wiring

Zone Doubling Table

Zone

Paired with zone

• Do not use zone doubling for fire

zones.

NOTE: A short across the EOL (i.e., at

terminal) on either zone of a zone-doubled

pair or on a double-balanced zone causes a

tamper condition (displayed as CHECK plus

zone numbers).

Smoke Detectors

1. Connect up to 16 (10, if “clean me” option used) 2-wire smoke detectors across zone 1

terminals 8 (+) and 9 (-) as shown in the Summary of Connections diagram at the

back this manual. Observe proper polarity when connecting the detectors.

2. Connect an EOL resistor across the loop wires at the last detector.

3. Connect 4-wire smoke detectors (up to 16, depending on detector current draw) to

any zone from 2-8 as shown in Figure 7 (on next page).

TO ZONE 1

TERMINALS

2-WIRE

Power Reset: This control does not automatically reset power to 4-wire smoke

detector zones, so you must use a relay (e.g., 4204, 4229), or on-board trigger to reset

power (also required for fire verification). Do this by programming the designated

relay/trigger as zone type 54 (fire zone reset); see On-Board Trigger section for

other information.

SMOKE

DETECTOR

ZONE 1

NOTE: Maximum current on trigger 17 is 100mA.

2-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting and Wiring the Control

Smoke Detector Notes

• Fire Verification (zone type 16): The control panel will “verify” a fire alarm by

resetting the smoke detectors after the first alarm trigger, and then waiting 90 seconds

for a second alarm trigger. If the smoke detector or thermostat does not trigger again,

the control will disregard the first trigger, and no alarm signal will occur. This feature

eliminates false alarms due to electrical or physical transients.

SIA Installations: If using fire verification on zones other than zone 1, UL Fire Alarm

Listed relay accessories must be used to reset power as described in the Power Reset

paragraph above.

• The zone 1 alarm current supports only one smoke detector in the alarmed state.

• Clean Me Option: If enabled (field *174 = 1; *56 zone programming, response time

prompt = 3), certain ESL smoke detectors send “clean me” reports as appropriate. If

used, the maximum number of detectors is reduced to 10 (not standard 16). Refer to the

ESL documentation included with the smoke detector for information regarding

compatibility with the clean-me option.

• Do not use 4-wire smoke detectors on zone 1.

RELAY

PROGRAM

BLK

RED

AUX PWR

OUTPUT

TERMINALS

RELAY

AS ZONE

TYPE 54

EOL

POWER

(FIRE ZONE

RESET)

N.O.

SUPERVISION

RELAY MODULE

A77-716B.

N.C.

USE N.O.

CONTACT OPENS

CONTACT,

WHICH CLOSES

WHEN POWER

IS APPLIED.

MOMENTARILY UPON

FIRE ALARM RESET

VIOLET

4-WIRE SMOKE

OR COMBUSTION

DETECTOR

2000

OHMS

EOLR

TO ZONE TERM. (

)

HEAT

DETECTOR

TO ZONE TERM. (

)

Figure 9a. 4-Wire Smoke Detector Using Relay for Power Reset

(

)

AUX PWR

BLK

RED

(

)

TO OUTPUT 17

PROGRAM OUTPUT 17

FOR "OUT NORM

EOL

POWER

SUPERVISION

RELAY MODULE

A77-716B.

LOW" = YES IN 79 MENU

MODE AND AS ZONE

TYPE 54 IN

N.O.

VIOLET

4-WIRE SMOKE

OR COMBUSTION

DETECTOR

USE N.O.

80 MENU MODE

2000

OHMS

EOLR

CONTACT,

WHICH CLOSES

WHEN POWER

IS APPLIED.

)

TO ZONE TERM. (

HEAT

DETECTOR

TO ZONE TERM. (

)

Figure 9b. 4-Wire Smoke Detector Using Output 17 for Power Reset

4219/4229 Expansion

Zones

1. Connect each module to the control’s keypad terminals and set the device addresses.

• VISTA-20P: Up to 40 expansion zones using up to 5 Zone Exp. Modules.

• VISTA-15P: Up to 16 expansion zones using up to 2 Zone Exp. Modules.

2. Connect sensors to the module’s loops. See Figure 8 on the following page.

• Use 1000 ohm end-of-line resistors at the end of loops connected to the 4219/4229

modules. (EOLRs used on the control terminals are 2000 ohms.)

•

Expansion zones have normal response time (300–500 msec), except zone connected

to each module’s loop “A,” which can be set for fast response (10–15 msec).

3. If using relays with the 4229, connect the desired field wiring to the unit's relay contact

terminals.

2-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

RELAY

CONNECTOR

4229

RELAY

DIP SWITCH

FOR SETTING ADDRESS

AND ZONE "A" RESPONSE

EITHER OR BOTH CAN BE USED

TERMINALS ON

CONTROL PANEL

RELAY

TB2

4-PIN CONSOLE PLUG

GRN

DATA OUT (>)

(TERM 6)

(TERM 4)

(TERM 5)

(TERM 7)

TO CONTROL

TAMPER JUMPER POSITION

4229 IN CABINET

(NOT TAMPER)

BLK

RED

YEL

(–) GROUND

4229 REMOTE

(TAMPER PROTECTED)

(+) 12VDC

TB1

DATA IN (<)

FROM

CONTROL

10 11 12

TERMINATE EACH

RLY

PROGRAMMED ZONE

WITH 1000 OHM (1K)

END-OF-LINE RESISTOR

(EACH ZONE'S MAX.

LOOP RESISTANCE

300 OHMS + EOL)

REED

(TAMPER)

SWITCH

RELAYS OFF

4229-002-V0

ZONES

Figure 10. Wiring Connections, 4219 & 4229 (4229 shown)

Installing the RF Receiver and Wireless Transmitter Zones

Compatible Receivers

Use any ADEMCO 5800 Series Wireless Receivers, such as:

RF Receiver

5881L/5882L

5881M/5882M up to 16

5881H/5882H, VISTA-20P = up to 40 plus 16 buttons

No. of Zones

up to 8

The 6150rf is a Medium receiver

only capable of support 16 wireless

zones

5883, 6150RF

VISTA-15P = up to 26 plus 8 buttons

Receiver Connections

1. Set Device Address to “00” (set all switches to the right, “off” position).

2. Mount the receiver, noting that the RF receiver can detect signals from transmitters

within a nominal range of 200 feet.

3. Connect the receiver's wire harness to the control's keypad terminals. Plug the

connector at the other end of the harness into the receiver. Refer to the installation

instructions provided with the receiver for further installation procedures regarding

antenna mounting, etc.

NOTE

ANTENNAS

(INSERT IN

RIGHT-HAND

TERMINALS)

CIRCUIT BOARD IS MOUNTED IN

CONTROL'S CABINET. GROUNDING

LUGS (2) PROVIDED MUST BE INSERTED

IN LEFT-HAND TERMINALS OF ANTENNA

BLOCKS AND SECURED TO CABINET.

(SEE RECEIVER'S AND CONTROL'S

INSTRUCTIONS)

INSERT IN

RIGHT- HAND

TERMINALS

YELLOW

RED

BLACK

GREEN

TO CONTROL'S

REMOTE KEYPAD

CONNECTION

POINTS.

WIRELESS ZONE

NUMBERS

MODEL NO. IS INDICATED ON CIRCUIT BOARD

5882

LOCATION

DIP

SWITCH

MOUNTING

HOLES

WIRING OPENING

INTERFERENCE

INDICATOR

LED

VISTA-20P:

transmitter zones 9-48

button zones 49-64

KNOCKOUT AREA

FOR SURFACE WIRING

CIRCUIT BOARD

VISTA-15P:

transmitter zones 9-34

button zones 49-56

PLUG

SOCKET

TO RELEASE CIRCUIT BOARD,

REMOVE SCREWS AND

BEND BACK TABS

5881-003-V0

Figure 11. 5881/5882 RF Receiver (cover removed)

Set the following options:

*22 RF Jam Option†

RF Receiver Notes

† These fields must be

enabled for Residential Fire,

UL Residential Burglar

Alarm, and UL Commercial

Burglar Alarm installations.

*24 RF House ID Code (if using wireless keypads) for each partition

*67 Transmitter Low Battery Report Code†

*75 Transmitter Low battery restore report code†

• The receiver is supervised and a trouble report is sent (“CHECK 100” displayed) if

communication between the panel and receiver is interrupted, or if no valid RF signals

from at least one supervised transmitter are received within 12 hours.

If the receiver is mounted remotely:

• Place the RF receiver in a high, centrally located area for best reception.

• Do not locate the receiver or transmitters on or near metal objects. This will decrease

range and/or block transmissions.

• Do not locate the RF receiver in an area of high RF interference (indicated by frequent

or prolonged lighting of the LED in the receiver; random flicker is OK).

• Do not locate RF receiver closer than 10 feet from any keypads to avoid interference

from the microprocessors in those units.

2-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting and Wiring the Control

Installing a 5800TM

Module

• Use this module only if you are using one or more wireless bi-directional keypads or

keyfobs with a wireless Receiver; 5800TM is not necessary if using a Transceiver (e.g.,

5883).

• The 5800TM must be set to address 28 (cut red-W1 jumper).

• The 5800TM can be used in partition 1 only.

• For additional information regarding the 5800TM, refer to the 5800TM’s instructions.

1. Mount the 5800TM next to the RF receiver (between one and two feet from the

receiver’s antennas) using its accompanying mounting bracket. Do not install within

the control cabinet.

2. Connect the 5800TM to the control panel’s keypad connection terminals as shown on

the Summary of Connections diagram and set to address 28.

Installing the

Transmitters

• Refer to the table of compatible devices at the back of this manual.

• Supervised transmitters† send check-in signals to the receiver at 70-90 minute

intervals. If at least one check-in message is not received from each transmitter within

a 12-hour period, the “missing” transmitter number(s) and “CHECK” is displayed. (†

Hand-held transmitters, e.g., 5802, 5802CP, 5804, 5804BD, 5827, 5827BD, do not send

check-in signals.)

• To be sure reception of the transmitter's signal at the proposed mounting location is

adequate, perform a Go/No Go Test, described in the Testing the System section.

• Install transmitters in accordance with the instructions provided with each.

• Set 5827, 5827BD, 5804BD wireless keypads to the programmed House ID (field *24),

using its DIP switches (5827) or follow the instructions provided with the device.

• Use *56 or *58 Zone Programming Menu modes to program zone information and enroll

transmitters (VISTA-20P: zones 9-48, buttons 49-64; VISTA-15P: zones 9-34, buttons

49-56).

• Wireless Keys: Use Wireless Key Programming Templates section of the *58 Zone

Programming Menu mode to program zone information and enroll each button of the

wireless keys used. Once a wireless key is enrolled, it must be assigned to a user before

it becomes active. See Adding/Deleting Security Codes section for procedure.

ULC NOTE: In accordance with ULC standards, the RF supervision period for the VISTA-20PCN

and VISTA-15PCN is three hours for Fire zones (Zone Type 9 and 16) and 12 hours for all other zone

types.

L The following transmitters are not intended for use in UL installations: 5802MN, 5802MN2, 5804,

5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850.

The 5827BD and 5800TM can be used in UL Listed Residential Burglar installations.

Transmitter Battery Life

• See Wireless Transmitter paragraph in the Limitations of This Alarm System

statement located at the end of this manual for information on transmitter battery

life.

• Some transmitters (e.g., 5802 and 5802CP) contain long-life but non-replaceable

batteries, and no battery installation is required. At the end of their life, the complete

unit must be replaced (and a new serial number enrolled by the control).

• Button-type transmitters (such as 5801, 5802, and 5802CP) should be periodically

tested for battery life.

• The 5802MN and 5804 Button Transmitters have replaceable batteries.

Do not install batteries in wireless transmitters until you are ready to enroll during

system programming. After enrolling, batteries need not be removed.

2-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Installing a Keyswitch

Keyswitch Connections

1. Connect the 4146 keyswitch's normally open momentary switch to a zone’s (2-8)

terminals. Remove the 2000 ohm EOL resistor if connected across the selected zone.

2. Using a standard keypad cable as shown:

Connect the yellow and white keyswitch wires to trigger connector pin 3 (+12V).

Connect the Red and Green LED wires to the appropriate output 17/output 18

trigger connector pins.

3. Connect a 2000 ohm EOL resistor across the momentary switch.

4. You can wire an optional closed-circuit tamper switch (model 112) in series with the

zone. If the switchplate is then removed from the wall, the tamper will open,

disabling keyswitch operation until the system is next disarmed from the keypad.

GREEN

RED

If the tamper is opened when the system is armed, an alarm will occur.

8-PIN TRIGGER CONNECTOR

STANDARD

KEYPAD

CABLE

4146 KEYSWITCH

(ARMED)

RED

YELLOW

(READY)

GREEN

WHITE

820

ohms

820

ohms

BLACK

RED

TAMPER

SWITCH (N. C.)

BROWN

BLUE

BROWN

TYPICAL ZONE

ON CONTROL

BOARD

LOCK

SWITCH (N. O.)

BLUE

EOLR

(use appropriate value)

Figure 12. Keyswitch Wiring Connections

Keyswitch Notes

A UL Listed keyswitch is required for fire installations and UL commercial and residential

burglar alarm installations. The Ademco 4146 keyswitch is UL Listed.

If a keyswitch is used on:

• an installation that transmits opening and closing signals, the keyswitch zone must be programmed

to send opening and closing signals.

• a UL commercial burglar alarm installation, the keyswitch’s tamper switch must be connected in to

the alarm system. This tamper switch zone must also be programmed for Zone Type 05 – Trouble

by Day / Alarm by Night.

• a fire alarm installation, the keyswitch must be located next to an alphanumeric display keypad.

• Use 4146 keyswitch or any N.O. keyswitch.

• Use only one keyswitch per partition.

• When using a keyswitch, the zone it is connected to is no longer available for use as a

protective zone.

• Use *56 Menu mode to program the keyswitch zone and assign it zone type 77.

• Use *80 Menu mode to program the LED functions: program outputs 17 and 18 for

system operation zone type 78 (red LED) and 79 (green LED) as appropriate (see

Output Device Programming section).

2-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting and Wiring the Control

Connecting Relay Modules, Powerline Carrier Devices and Output Triggers

4204/4229 Relay Modules

1. Mount either remotely or in the control panel.

2. Connect each module to the control’s keypad terminals and set the device addresses

as previously described in the Connecting Keypads and Other Addressable

Device section. Use the connector harness supplied with the module. Use standard

4-conductor twisted cable for long wiring runs.

VISTA-20P: Up to 16 relays (if no powerline carrier devices are used)

VISTA-15P: Up to 8 relays (if no powerline carrier devices are used)

3. Connect the desired field wiring to the unit's relay contact terminals.

RELAY

4204

DIP SWITCH

FOR SETTING DEVICE ADDRESS

AND ENABLING/DISABLING TAMPER

TYPICAL

(SHOWN "OFF")

^RE3^LAY

COVER TAMPER (REED) SWITCH

For UL installation

RELAY

4-PIN TOUCHPAD PLUG

requirements, refer to the

Installation Instructions for

the 4204.

EITHER OR BOTH

CAN BE USED

RELAY

TB1

13 14 15 16

DATA IN

FROM CONTROL

YEL

BLK

GRN

RED

TB2

(–) GROUND

DATA OUT

TO CONTROL

(+) 12V

4204_conn-1-V0

Figure 13. 4204 Connections to Control

• Supervision: 4204 and 4229 modules are supervised against removal. The module’s

device address is displayed as follows if a module is disconnected from the control’s

terminals, or if the module cover is removed and the tamper jumper is installed:

Alpha: CHECK xx Wire Expansion

FAULT xx Wire Expansion

ALARM xx Wire Expansion

Fixed-Glass: lxx (or 91 if field *199 set for 2-digit display)

where “xx is the module’s address.

• If communication/tamper failure occurs on a device with zones wired to it, all zones on

the device will be displayed in their respective partitions.

1. Install the powerline carrier devices according to the instructions included with each.

VISTA-20P: Up to 16 devices (if no relays are used)

Powerline Carrier

Devices

VISTA-15P: Up to 8 devices (if no relays are used)

2. Use Programming Mode to enter the device house ID in data field*27, and enter the

unit code using *79 Output Device menu Mode.

3. See connections diagram in the AC Wiring section for connecting the 1361X10

transformer to the triggers.

Powerline Carrier

devices and the 1361X10

Transformer are not UL

Listed for fire or burglary

functions and are intended

for home automation.

• You must use a 1361X10 Transformer instead of the 1321 Transformer.

•

The 1361X10 Transformer provides AC power to the control panel, and also supplies

signals from the control panel through the premises AC wiring to the Powerline

Carrier devices (which are plugged into AC outlets). You can then make devices that

are plugged into Powerline Carrier devices perform various functions in response to

commands you enter at the security system keypads.

Canada: Use the PSC04 Powerline Interface as shown below.

8-PIN TRIGGER CONNECTOR

X-10 PSC04

POWERLINE INTERFACE

SA4120XM-1 CABLE

SYNC

BLK

MODULAR PHONE CORD (not supplied)

1 - BLACK

2 - RED

3 - GREEN

4 - YELLOW

GRN

COM

DATA

RED

YEL

Figure 14. PSC04 Powerline Interface Connections

2-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

On-Board Triggers

Connect field wiring to the desired trigger pin on the 8-pin trigger connector centrally

located above the terminal strip.

• If using 1361X10 transformer and powerline carrier devices, use the SA4120XM-1

cable (part of 4120TR Trigger Cable). See Wiring the AC Transformer section for

transformer connections.

• If only using the on-board triggers, you can use a 4-wire cable (N4632-4, supplied

with the control) as shown below.

8-PIN TRIGGER CONNECTOR

4-WIRE

CABLE

SA412OXM-1

CABLE

00-trigcon-005-V2

00-trigcon-003-V1

Figure 15a. On-Board Trigger Connector

with SA4120XM-1 Cable for Use With

1361X10 Transformer

Figure 15b. On-Board Trigger Connector

with 4-Wire Cable for Trigger Use Only

• Trigger outputs are normally high, and go low upon programmed condition.

• The outputs can be programmed for inverted operation (normally low, go high) using

*79 Menu mode.

• Program these triggers using *80/*81 Menu modes as you would for any other relay

output.

• When using these outputs, note:

pin 1 = output number 17 (trigger 1):

15 ohms to ground when closed (output low), open when off (output high, normal

default); can be used to reset smoke detector power (must set “output normal low

= yes” in *79 Menu mode, and set for zone type 54, fire zone reset, in *80 Menu

mode); or can support 12V relay module (e.g., Altronix AX-RBS) that draws less

than 100mA

pin 5 = output number 18 (trigger 2):

100 ohms to ground when closed (output low); open when off (output high,

normal default); or can support 12V relay module that draws less than 20mA

If on-board triggers are used, the wiring between the control unit and the UL Listed device must

be run in conduit, be no more than 3 feet apart and have no intervening barriers or walls.

2-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Mounting and Wiring the Control

Phone Line/Phone Module, and Audio Alarm Verification (AAV) Connections

Phone Line

Connect incoming phone line and handset wiring to the main terminal block (via an

RJ31X jack) as shown in the Summary of Connections diagram at the back of this

manual.

Wire colors represent the colors of the cable to the RJ31X jack.

1. Make 12V (+) and (–) and data in and data out connections from the phone module to

the control, using the connector cable supplied with the phone module, then insert

the keyed connector at the other end of the connector cable into the header on the

phone module.

4285/4286 Phone Module

2. Connect Phone Module terminals as shown below. Use an RJ31X jack with a direct-

connect cord and make all connections exactly as shown.

3. Caller ID Units: If a Caller ID unit is being used, connect the unit directly to the

“Handset” terminals (21 & 22) on the control, as shown.

Compatibility: 4286 Phone

Modules must have

INCOMING

GROUND

HANDSET TELCO LINE

software version WA4286-

15.1 or higher (refer to the

label on the square 4286

microprocessor chip).

TERMINALS

ON CONTROL

TO EARTH GROUND (COLD WATER PIPE, ETC.)

INCOMING TELCO LINE

CALLER ID

UNIT

DIRECT

CONNECT

CORD

TIP

IMPORTANT NOTE FOR

EXISTING INSTALLATIONS:

RJ31X

RING

JACK

EXISTING WIRES

CONNECTED TO THE

The 4285 and 4286

CA38A

CANADA

"HANDSET" TERMINALS ON

CONTROL MUST BE MOVED

FROM THERE TO TERMINALS

3 AND 4 ON THE 4285/4286.

PREMISES ANSWERING

MACHINE AND PHONES

PLUG

modules are UL Listed only

for use on residential fire

and UL residential burglar

alarm installations.

ANSWERING

MACHINE

4285/4286

VIP MODULE

LOUDER

VOLUME

(4286

ONLY)

KEYED

HEADER

* NOTE: IF THE TELEPHONE HAS BUILT-IN CALLER ID,

THE CALLER ID FUNCTION MAY NOT WORK.

UNUSED

4285/4286

TERMINAL ASSIGNMENTS

TO CONTROL

PANEL

TERMINALS

USED FOR

KEYPAD

YELLOW: TO DATA OUT (term. 7)

NO CONNECTION

1 - TIP

2 - RING

3 - TIP

4 - RING

PHONE INPUT

}

RED:

TO AUX (+) (term. 5)

CONNECTOR

WITH FLYING

LEADS

BLACK: TO AUX. GROUND (–) (term.4)

GREEN: TO DATA IN (term. 6)

PHONE OUTPUT

}

5 - NO CONNECTION

CONNECTIONS

6 -

7 -

AUDIO OUT

4286 ONLY

}

Figure 16. 4285/4286 Phone Module Wiring Connections

• Only one phone module can be used and it can only be connected to partition 1.

• The phone lines must be in service for the phone module to function, even when

accessing the system from an on-premises phone.

• If you are also using an Audio Alarm Verification (AAV) unit, refer to Audio Alarm

Verification (AAV) section for special wiring connections.

CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication

line cord for phone line connections.

Phone Module Problems

If no touch tones are produced following access to the security system from on-premises

(this problem may arise in rare cases), it may be necessary to reverse the wires connected

to terminals 3 and 4 on the phone module and the wires connected to terminals (21) &

(22) on the control. The wiring diagram shows the wiring connections that will provide

proper operation in most cases.

Connection to the incoming telco line via a RJ31X jack and direct-connect cord, as shown,

is essential, even if the system is not connected to a central station. The 4285 or 4286 will

not function if this is not done and an error signal (fast busy signal) will occur when

trying to access the system via the phone.

The house phone lines (gray and brown wires) must be wired to the phone module

terminals; not to the control terminals. Otherwise, an error signal (fast busy signal) will

occur when trying to access the system from an on-premises phone.

2-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Audio Alarm Verification

Connections

(AAV, “listen-In”)

• Refer to the connection diagrams below. One diagram shows connections when a

4285/4286 Phone Module is used, the other shows connections when the 4285/4286 is not

used.

• Connections use one of the on-board triggers.

• Set field *91 for AAV and program the appropriate output (output 17 or 18) using *80

Menu mode: select zone type 60 and output action 1 (close for 2 seconds) or action 2 (stay

closed).

• For voice session monitoring, connect an EOLR zone to UVCM module terminals 6 & 7,

and program the zone as zone type 81 (*56 Menu mode).

E.g., Using output 18 for the trigger, program an output function in *80 Menu mode as:

ZT = 60, P = 0, Action = 1, Device = 18

• Suggested AAV Module: ADEMCO UVS (shown) or Eagle 1250

UL installations using the AAV feature must use the ADEMCO UVCM module (part of the

ADEMCO UVS system).

TRIGGER

CONNECTOR

EARTH

GROUND

ZONE

TERMINALS

CONTROL

AUXILIARY

AUDIO LEVEL

ADJUSTMENT

TRIM POT

21 22 23

24 25

EOL

RING

TIP

UVCM

MODULE

RED (R)

GREEN (T)

GREY (R)

RJ31X

BROWN (T)

NOTE:

REFER TO UVCM MODULE

INSTRUCTIONS FOR

CONNECTIONS TO AUDIO

SPEAKERS AND MICROPHONE.

OPTIONAL

MONITORING ZONE

CONNECTION

(USE ZONE TYPE 81)

PREMISES

HANDSET

SWITCH

BANK 1

SWITCH

BANK 2

1 = OFF

2 = OFF

3 = OFF

4 = OFF

5 = OFF

6 = OFF

7 = OFF

8 = ON

1 = ON

2 = ON

3 = OFF

4 = ON

5 = ON

6 = ON

7 = ON

8 = ON

INCOMING

PHONE LINE

FALLING VOICE TRIG

GND

+12VDC IN

Figure 17a. Connection of AAV Unit When Not Using a 4285/4286 Phone Module

TRIGGER

CONNECTOR

EARTH

GROUND

ZONE

TERMINALS

CONTROL

AUXILIARY

AUDIO LEVEL

ADJUSTMENT

TRIM POT

21 22 23 24 25

EOL

RING

TIP

UVCM

MODULE

RING

TIP

RED (R)

GREEN (T)

GREY (R)

RJ31X

OPTIONAL

MONITORING

ZONE

CONNECTION

(USE ZONE

TYPE 81)

BROWN (T)

NOTE:

REFER TO UVCM MODULE

INSTRUCTIONS FOR

CONNECTIONS TO AUDIO

SPEAKERS AND MICROPHONE.

PREMISES

HANDSET

SWITCH

BANK 1

SWITCH

BANK 2

1 = OFF

2 = OFF

3 = OFF

4 = OFF

5 = OFF

6 = OFF

7 = OFF

8 = ON

1 = ON

2 = ON

3 = OFF

4 = ON

5 = ON

6 = ON

7 = ON

8 = ON

INCOMING

PHONE LINE

FALLING VOICE TRIG

4285/4286

GND

+12VDC IN

Figure 17b. Connection of AAV Unit When Using a 4285 or 4286 Phone Module

2-14

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Programming Overview

About Programming

• You can program the system at any time, even at the installer's premises prior to the actual installation.

• Programming can also be performed remotely from the installer’s office/home, using an IBM personal

computer, a modem, and Compass downloading software.

The following is a list of the various Programming modes used to program this system.

Programming Mode…

Used to …

Data Field Programming

Program basic data fields used for setting the various system options.

Most of the data fields in this system have been programmed for specific default

values. However, some fields must be programmed for each particular installation to

establish its specific alarm and reporting features.

Assign zone characteristics, report codes, alpha descriptors, and serial numbers for

5800 RF transmitters. See *56 Zone Programming in Section 5. Menu Mode

Programming for procedures for programming zones.

∗56 Zone Programming

Program each of the four alphabet function keys to perform one of several system

operations.

∗57 Function Key

Programming

∗58 Zone Programming

Similar to ∗56 mode, but provides a faster programming procedure and is intended for

those more experienced in programming controls of this type.

Assign device addresses used by 4229 or 4204 Relay modules and map specific relays

and device outputs, and assign unit codes for Powerline Carrier devices.

See About Output Device Programming in Section 5. Menu Mode

Programming for details on setting devices for manual/automatic operation.

Define up to 48 output definitions which can control the output relays mapped using

*79 Output Device Mapping mode.

(Expert Mode)

∗79 Output Device Mapping

∗80 Output Definitions

Create Zone Lists for relay/powerline carrier zones, chime, night-stay, cross zones,

and pager zones.

∗81 Zone List Programming

Create alpha descriptors for easy zone identification.

Create schedules to automate various system functions.

∗82 Alpha Programming

Scheduling Mode

(code + [#] +64)

Mechanics of Programming

To program the system from a keypad:

• You must use a 2-line Alpha display keypad.

• Both partitions must be disarmed.

Data Field Programming Procedures

Task

Procedure

Entering Program Mode

∗

A) Press both [ ] and [#] at the same time within 50 seconds after power is applied,

B) After power-up, enter [Installer code (4-1-1-2)] + 8 0 0 (long beep indicates one of the

partitions is armed and system cannot enter program mode).

∗

(method “B” is disabled if you exit Program mode using 98)

Go to a Data Field

Entering Data

∗

Press [ ] + [Field Number]. A display of “EE” or “Entry Error” means you have entered a

∗

nonexistent field. Simply re-enter [ ] plus a valid field number.

When the desired field number appears, simply enter the digits required. The keypad

beeps three times after the last digit is entered and automatically displays the next data

field in sequence.

If entering less than the maximum digits available (e.g., phone number field), enter the

∗

desired digits, then press [ ] to end the entry.

Press [#] + [Field Number]. The field’s data is displayed, but no changes can be made.

Review a Data Field

Deleting an Entry

∗

Press [ ] + [Field No.] + [ ] (applies only to phone number, account number, and pager

character fields).

3-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Interactive Mode Programming (∗56, *57, ∗58, ∗79, ∗80, ∗81, ∗82)

Entering Interactive Mode

∗

Press [ ] + [Interactive Mode No.] (for example, 56) while in Program Mode. The Alpha

display keypad will display the first of a series of prompts.

After making the appropriate entry, press the [∗] key to accept the entry and continue to

the next prompt.

Loading Factory Defaults/Initializing for Download

To Load Default Entries

Press ∗97 while in Program Mode. This resets all data fields to the default values shown

∗

on the Program Form. Use 97 only if you wish to return to the original factory-

programmed defaults.

To Initialize Download ID

Press ∗96 while in Program Mode. This initializes the system for downloading and resets

all the subscriber account numbers and CSID.

✱

Do not press 97 to load defaults if any programming has been done previously—data

already programmed into the system will be changed!

Exiting the Programming Mode

Prevent installer code

reentry

Press ∗98. Exits Programming Mode and prevents re-entry by:

∗

Installer Code + [8] + [0] + [0]. To enter the programming mode if 98 was used to exit,

you must first power the system down. Then power up again, and press [∗] and [#] at the

same time, within 50 seconds of powering up.

See field *88 for other Program mode lockout options.

Allow installer code

reentry

Press ∗99. Exits Programming Mode and allows re-entry by:

Installer Code + [ 8] + [0] + [0] or by: Pressing [∗] and [#] at the same time, within 50

seconds of power-up.

Zone Type Definitions

Zone types define the way in which the system responds to faults in each zone.

Zone Type

Type 00

Description

Program a zone with this zone type if the zone is not used.

Zone Not Used

Type 01

Entry/Exit

Burglary #1

• Assign to zones that are used for primary entry and exit.

• Provides entry delay when zone is faulted if control is armed in the Away, Stay, or Night-Stay

modes.

• No entry delay provided when the panel is armed in the Instant/Maximum mode.

• Entry delay #1 is programmable for each partition (field *35).

• Exit delay begins whenever the control is armed, regardless of the arming mode selected, and

✱

is programmable (field 34).

Type 02

Entry/Exit

Burglary #2

• Assign to zones that are used for entry and exit and require more time than the primary

entry/exit point.

• Provides a secondary entry delay, in same manner as entry delay #1.

• Entry delay #2 is programmable for each partition (field *36).

• Exit delay is same as described for Type 01.

• Assign to all sensors or contacts on exterior doors and windows.

• Provides an instant alarm if the zone is faulted when the panel is armed in the Away, Stay,

Night-Stay, Instant or Maximum modes.

Type 03

Perimeter

Burglary

Type 04

Interior Follower

• Assign to a zone covering an area such as a foyer, lobby, or hallway through which one must

pass upon entry (to and from the keypad).

• Provides a delayed alarm (using the programmed entry 1 time) if the entry/exit zone is faulted

first. Otherwise this zone type gives an instant alarm.

• Active when the panel is armed in the Away mode.

• Bypassed automatically when the panel is armed in the Stay or Instant modes;

if armed in Night-Stay mode, zones assigned to zone list 05 (night-stay zone list) are not

bypassed when system armed in Night-Stay mode.

3-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming Overview

Type 05

Trouble by Day/

Alarm by Night

• Assign to a zone that contains a foil-protected door or window (such as in a store), or to a zone

covering a sensitive area such as a stock room, drug supply room, etc.

• Can also be used on a sensor or contact in an area where immediate notification of an entry is

desired.

• Provides an instant alarm if faulted when armed in the Away, Stay, Night-Stay, Instant or

Maximum (night) modes.

• During the disarmed state (day), the system will provide a latched trouble sounding from the

keypad (and a central station report, if desired).

• Usually assigned to a zone containing an emergency button.

• Sends a report to the central station but provides no keypad display or sounding.

Type 06

24-hr Silent Alarm

Type 07

24-hour Audible

Alarm

• Assign to a zone that has an emergency button.

• Sends a report to the central station, and provides an alarm sound at the keypad, and an

audible external alarm.

Type 08

24-hour

Auxiliary Alarm

• Assign to a zone containing an emergency button, or to a zone containing monitoring devices

such as water or temperature sensors.

• Sends a report to the central station and provides an alarm sound at the keypad. (No bell

output is provided.)

Type 09

Supervised Fire

• Provides a fire alarm on short circuit and a trouble condition on open circuit. A fire alarm

produces a pulsing bell output.

• This zone type is always active and cannot be bypassed.

Type 10

Interior w/Delay

• Provides entry delay (using the programmed entry time), if tripped when the panel is armed in

the Away mode.

• Entry Delay 1 begins whenever sensors in this zone are violated, regardless of whether or not

an entry/exit delay zone was tripped first.

• Bypassed when the panel is armed in the Stay or Instant modes; if armed in Night-Stay mode,

zones assigned to zone list 05 (night-stay zone list) are not bypassed when system armed in

Night-Stay mode.

Type 12

Monitor Zone

• Works as a dynamic monitor of a zone fault/trouble (not alarm). In the case of a short/open, the

message, "*ALARM*-24 Hr. Non-Burg. -#XXX " (where XXX is the zone number) will be sent

to the Central Station. The system keypad will display a “check” message indicating the

appropriate zone (but keypad beeping does not occur). Upon restoral of the zone, the message,

"*RESTORE*-24 Hr. Non-Burg. -#XXX " will be sent to the Central Station.

• The “check” message will automatically disappear from the keypad dynamically, when the

zone restores; a user code + off sequence is not needed to reset the zone.

• Faults of this zone type are independent of the system, and can exist at the time of arming

without interference.

• Since this is a “trouble” zone type, do not use this zone type with relays set to activate upon

“alarm.”

• Assigned to any zone with a carbon monoxide detector.

• The bell output will pulse when this zone type is alarmed.

• Always active and cannot be bypassed.

Type 14

24 Hour Carbon

Monoxide

Monitor

Type 16

Fire

w/Verification

• Provides a fire alarm when zone is shorted, but only after alarm verified.

• System verifies alarm by resetting zones for 12 seconds after short is detected. A subsequent

short circuit within 90 seconds triggers fire alarm.

• Provides a trouble response when zone is open.

• Arms the system in Stay mode when the zone is activated.

• Pushbutton units send the user number to the central station when arming or disarming.

• User number for button must be assigned.

Type 20

Arm-Stay (BR

only)

Type 21

Arm-Away (BR

only)

• Arms the system in Away mode when the zone is activated.

• Pushbutton units send the user number to the central station when arming or disarming.

• User number for button must be assigned.

Type 22

Disarm (BR only)

• Disarms the system when the zone is activated.

• User number for button must be assigned.

3-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Type 23 *

No Alarm

Response

• Can be used on a zone when an output relay action is desired, but with no accompanying

alarm (e.g., lobby door access).

Type 24

Silent Burglary

• Usually assigned to all sensors or contacts on exterior doors and windows where bells and/or

sirens are NOT desired.

• Provides an instant alarm, with NO audible indication at any keypad or external sounder, if

the zone is faulted when the system is armed in the Away, Stay, Instant, or Maximum modes.

• A report is sent to the central station.

Type 77

Keyswitch

• Assign to zone wired to a keyswitch.

• Do not use devices assigned as input type “BR” with this zone type.

Type 81

AAV Monitor

Zone

• Assign to zone connected to AAV module.

• Monitors 2-way voice sessions as follows:

- When the zone is faulted, all alarm sounding and dialer reporting stops, except

for fire alarms, which immediately terminate the voice session and cause

a fire report to be sent.

- When the zone is restored (session ended), sounding resumes (if bell timeout

has not expired) and reports that were stopped are sent.

Allows for various custom responses. Options include response to entry/exit delays, response

opens/shorts, types of alarm/trouble sounding, dial delay, and unique Contact ID report codes.

Types 92 and 93 can only be programmed via downloader. UL installations: Zone Types 90 -93

may not be used as fire or burglar alarm zones on fire or UL burglar alarm installations.

Types 90-93

Configurable

* The system can still be armed when these zone types are in a faulted condition.

NOTE: All of the zone types described are available for the wireless portion of the system, if used.

3-4

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Data Field Programming

About Data Field Programming

The following pages list this control’s data fields in numerical order. Valid entries for each field are shown

in italics. Explanations and special notes are presented below the entries.

Use the separate Programming Guide to record the data for this installation.

Data field programming involves making the appropriate entries for each of the data fields.

Start Data Field programming by entering the installer code + 8 + 0 + 0.

SIA Guidelines: Notes in certain fields give instructions for programming the VISTA-20P/VISTA-15P for False Alarm

Reduction. Fields unique to the VISTA-20PSIA/VISTA-15PSIA are indicated by heavy borders and reverse type

heading “V20PSIA/V15PSIA” for easy identification.

∗

System Setup Fields ( 20 – ∗29)

*20

*27

Powerline Carrier Device (X-10) House ID

Installer Code

Enter 4 digits, 0-9

0 = A; 1 = B; 2 = C; 3 = D; 4 = E; 5 = F; 6 = G; 7 = H;

8 = I; 9 = J; # + 10 = K; # + 11 = L; # + 12 = M;

# + 13 = N; # + 14 = O; # + 15 = P

The Installer Code can perform all system functions

except it cannot disarm the system unless it was used

to arm the system.

Powerline Carrier devices require

House ID,

identified in this field. Program Powerline Carrier

devices in interactive modes ∗79, *80 and *81.

Not intended for fire or UL installations.

*21

Quick Arm Enable

0 = do not allow quick arm; 1 = allow quick arm

If enabled, a user code is not needed to arm the system.

Instead, users can press the [#] followed by an arming

key to arm the system. However, the user code is always

needed to disarm the system.

*28

Access Code for Phone Module

1-9 = first digit of access code

∗ or # = second digit of access code

(# +11 for “∗”, or # +12 for “#”)

*22

RF Jam Option

You must assign a 2-digit access code for the 4285/4286

Phone Module, if used. Example: If desired access code

is 7∗, then 7 is the first entry, and [#] + 11 (for ∗) is the

second entry.

0 = no RF jam detection; 1 = send RF jam report

If enabled, a report is sent if the system detects an RF

jamming signal.

UL installations must be 1 if wireless devices are used.

NOTE: A 0 in either digit disables the phone module.

Must be 00 for UL Commercial Burglar Alarm

installations.

*23

Quick (Forced) Bypass

0 = no quick bypass

1 = allow quick bypass (code + [6] + [#] )

Zones bypassed by this function will be displayed after

the bypass is initiated.

*29

Long Range Radio Output

0 = not used; 1 = using Long Range Radio output

If selected, all messages programmed to go to the

primary telephone line receiver will also be sent to the

connected 7720PLUS, 7820, 7835, or 7845 Radio (sent

in Contact ID format). The data line is supervised as

well as certain functions in the radio. If communication

is lost or a trouble develops, an attempt will be made to

send a message via both radio and telephone to the

central station. Program the radio for device address 3.

UL installations must be 0 (no forced bypass)

*24

RF House ID Code

00 = disable all wireless keypad usage

01–31 = House ID for partition 1, 2 and common

The House ID identifies receivers and wireless

keypads. If a 5827 or 5827BD Wireless Keypad or

5804BD Transmitter is being used, a House ID code

must be entered and the keypad set to the same House

ID. You can assign RF house ID for each partition.

Zone Sounds & Timing (∗31–∗39)

*31

Single Alarm Sounding Per Zone (per armed period)

*26

Chime By Zone List 3

0 = no limit on alarm sounding per zone

1 = limit alarm sounding to once per arming period for a

given zone

0 = no zone list (chimes on fault of any entry/exit or

perimeter zone when chime mode on)

1 = use zone list (chimes on fault of specific zones

programmed in relay zone list 3 when Chime mode on)

If enabled, you can define the specific zones intended

to chime when faulted while the system is in Chime

mode. Use zone list 3 to assign these zones (see ∗81

Zone List Programming section for details).

V20PSIA/V15PSIA: If “0” selected, “alarm sounding

per zone” will be the same as the “number of reports

in armed period” set in field *93 (1 if one report, 2 if 2

reports, unlimited for zones in zone list 7).

4-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

*32

*38

Confirmation Of Arming Ding

Fire Alarm Sounder Timeout

0 = yes; sounder timeout after time selected in field ∗33

0 = no ding; 1 = confirmation ding after arming system

2 = ding after arming from RF button or RF keypad only

Confirmation of arming is 1/2-sec external sounder “ding.”

If 1 selected, ding occurs when closing report is sent, or

at the end of Exit Delay.

1 = no timeout; sounds until manually turned off

This control complies with NFPA requirements for

temporal pulse sounding of fire notification appliances.

Temporal pulse sounding for a fire alarm consists of the

following: 3 pulses – pause – 3 pulses – pause – 3 pulses.

UL fire alarm installations: must be 1.

If 2 selected, ding occurs upon reception of the wireless

arming command.

UL Installations: must be 1 for UL Commercial

Burglar Alarm installations.

*33

Alarm Sounder Timeout

0 = No timeout; 1 = 4 min; 2 = 8 min; 3 = 12 min; 4 = 16 min

This field determines whether the external sounder

will shut off after time allotted, or continue until

manually turned off.

*39

Power-Up In Previous State

0 = always power-up in a disarmed state

1 = assume the system status prior to power down

When the system powers up armed, an alarm will

occur 1 minute after arming if a zone is faulted.

Note that if the previous state was armed Away or Stay,

the system will not respond to sensor changes for 1

minute, which allows sensors such as PIRs to stabilize.

UL Installations: must be 1 (power-up in previous state)

SIA Guidelines: must be 1

UL Installations: For residential fire alarm

installation, must be set for a minimum of 4 min

(option 1); for UL Commercial Burglary installations,

must be minimum of 16 min (option 4).

*34

Exit Delay

00 - 96 = 0 - 96 seconds; 97 = 120 seconds

V20PSIA/V15PSIA: 45 - 96 = 45 - 96 secs; 97 = 120 secs

NOTE: Entries less than 45 will result in a 45-sec delay.

∗

Dialer Programming ( 40 – 50)

*40

PABX Access Code or Call Waiting Disable

The system waits the time entered before arming

entry/exit zones. If the entry/exit door is left open after

this time expires, an alarm will occur. Common zones

use same delay as partition 1.

UL installations: For UL Commercial Burglar Alarm

(Grade AA) and UL Residential Burglar Alarm

installations with line security, total exit time must

not exceed 60 seconds. For UL Burglar Alarm

installations without line security (Grade A), total exit

time must not exceed 120 seconds.

Enter up to 6 digits if PABX is needed to access an

outside line. Do not fill unused spaces. 0–9, # + 11 for ‘∗’,

# + 12 for ‘#’, # + 13 for a pause (2 seconds)

To clear entries from field, press ∗40∗. If fewer than 6

digits need to be entered, exit by pressing [∗].

Call Waiting: If the subscriber’s phone service has

“call waiting” (and is not using PABX), enter “*70” (“#

+ 11”) plus “# + 13” (pause) as the PABX entry to

disable “call waiting” during control panel calls. If the

subscriber does not have “call waiting” and is not using

PABX, make no entry in this field.

SIA Guidelines: minimum exit delay is 45 seconds

*35

*36

NOTES: 1. The call waiting disable feature cannot be

used on a PABX line. 2. Using Call Waiting Disable on

a non-call waiting line will prevent successful

Entry Delay 1 (*35), Entry Delay 2 (*36)

00 - 96 = 0 - 96 seconds; 97 = 120 secs; 98 = 180

secs; 99 = 240 secs

communication to the central station.

V20PSIA/V15PSIA: 30-96 = 30 - 96 secs;

97 = 120 secs; 98 = 180 secs; 99 = 240 secs

NOTE: Entries less than 30 will result in a 30-sec delay.

V20PSIA/V15PSIA: If call waiting is used, enter call

waiting disable digits as described above, and also set Call

Waiting Disable option in field *91.

Upon entering, the system must be disarmed before

the time entered expires, otherwise it sounds an alarm.

Common zones use same delay as partition 1.

UL Installations: For UL Residential Burglary Alarm

installations, must be set for a maximum of 30 seconds;

entry delay plus dial delay should not exceed 1 min.

For UL Commercial Burglar Alarm, total entry delay

may not exceed 45 seconds.

*41

Primary (*41) and Secondary (*42) Phone No.

*42 _{Enter up to 20 digits. 0–9, # + 11 = ‘∗’, # + 12 = ‘#’,}

# + 13 = pause (2 secs)

If entering fewer than 20 digits, exit by pressing [∗] +

next field number. To clear entries, press ∗41∗ or *42*

respectively. Do not fill unused spaces.

NOTE: Backup reporting (see field *49) is automatic

only if there is a secondary phone number (field ∗42).

SIA Guidelines: minimum entry delay is 30 seconds

*37

Audible Exit Warning

*43

*44

*45

*46

Primary/Secondary Account Numbers

Enter 4 or 10 digits, depending on selection in

*48 Report Format field. Enter 0–9; # + 11 = B,

# + 12 = C, # + 13 = D, # + 14 = E, # + 15 = F.

0 = no; 1 = yes

Warning sound consists of slow continuous beeps until

the last 10 seconds, and then it changes to fast beeps.

Sound ends when exit time expires.

SIA Guidelines: must be enabled (enter 1)

*43: Partition 1 primary. To clear entries: ∗43∗.

*44: Partition 1 secondary. To clear entries: ∗44∗.

*45: VISTA-20P. Part. 2 prim. To clear entries: ∗45∗.

*46: VISTA-20P. Part. 2 second. To clear entries: ∗46∗.

V20PSIA/V15PSIA: feature always enabled; field does

not exist.

4-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Programming

*47

*54

Dynamic Signaling Delay

Phone System Select

If Central Station Receiver is not on WATS line:

0 = Pulse Dial; 1 = Tone Dial

0 = disabled (both signals sent);

1–15 = entry times a 15-second delay.

If Central Station Receiver is on WATS line:

2 = Pulse Dial; 3 = Tone Dial

Select the type of telephone service.

e.g., 1 = 15 seconds, 2 = 30 seconds, etc.

Intended for use with Long Range Radio reporting.

This field lets you select the time the panel should wait

for acknowledgment from the first reporting

destination (see ∗55) before it attempts to send a

message to the second destination. Delays can be

*48

Report Format (Primary/Secondary)

0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

5 = ADEMCO 10-digit Contact ID®

6 = 4+2 ADEMCO EXPRESS

selected from

to 225 seconds, in 15-second

increments. This delay is per message. If 0 is entered

in this field, the control panel will send redundant

reports to both Primary Dialer and LRR.

7 = ADEMCO 4-digit Contact ID®

8 = 3+1, 4+1 ADEMCO L/S EXP.

9 = 3+1, 4+1 RADIONICS EXP.

UL Installations:

For Fire Alarm and UL Burglar Alarm installations

without Line Security (Grade A), the maximum

Dynamic Signaling Delay must be no more than 15 secs.

For UL Burglar Alarm installations with Line

Security (Grade AA), Dynamic Signaling Delay must

be 0. Reports will be sent to both the dialer and the LRR.

Select format for primary/secondary phone numbers.

*49

Split/Dual Reporting

standard/backup reporting only (see Backup

Reporting below)

To Primary No.

To Secondary No.

*55

Dynamic Signaling Priority

1 = alarms, restore, cancel

2 = all except open/close, test

3 = alarms, restore, cancel

4 = all except open/close, test

5 = all

others

0 = Primary dialer first; 1 = Long Range Radio (LRR) first.

Intended for use with Long Range Radio reporting.

You must also enable field ∗29, OUTPUT TO LONG

RANGE RADIO.

open/close, test

all

Select the initial reporting destination for messages as

follows:

Primary Dialer First selected (0):

• If acknowledged before delay expires (see ∗54), then

message will not be sent to LRR.

Backup Reporting: All reports are sent only to the

primary number unless unsuccessful after 8 attempts.

If unsuccessful, the system will make up to8 attempts

to send all reports to the secondary number. If still

unsuccessful after the 16 attempts, the system

displays the “COMM. FAILURE” message (FC for

fixed-word displays).

• If not acknowledged before delay expires, message is

sent to both the Primary Phone No. and LRR.

Long Range Radio First selected (1):

• If acknowledged before delay expires, then message

will not be sent to the primary dialer.

• If not acknowledged before delay expires, message is

sent to both the Primary Phone No. and LRR.

UL Installations: For UL Commercial Burglary

installations that use a DACT and LRR, the DACT

must be programmed for priority (option 0).

*50

Burglary Dialer Delay

0 = no dial delay; 1 = 15 secs; 2 = 30 secs; 3 = 45 secs

UL: must be 0.

SIA Guidelines: delay must be minimum 30 seconds

V20PSIA/V15PSIA:

Delay Time: 1 = 15 secs; 2 = 30 secs; 3 = 45 secs

Delay Disable:

0 = use delay set in entry 1

1 = dial delay disabled for zones listed in zone list 6

(use zone list 6 to enter those zones that require

dial delay to be disabled; these zones ignore the

setting in entry 1)

*56

Zone Programming Menu Mode

For programming zone information.

See Zone Programming section for procedures.

UL: Dial delay plus entry delay must not exceed one

minute; use zone list 6 to disable dial delay from

appropriate zones, if necessary.

*57

Function Key Menu Mode

For programming keypad function keys.

See Function Key section for procedures.

Provides delay of “BURGLARY ALARM” report to the

central station, which allows time for the subscriber to

avoid a false alarm transmission. This delay does not

apply to zone type 24 alarms (silent burglary) or to 24-

hour zone types 6, 7, and 8 (silent panic, audible

alarm, auxiliary alarm), which are always sent as soon

as they occur.

*58

Expert Zone Programming Menu Mode

For quickly programming zone information, but is

recommended only for those already familiar with *56

menu mode. See Zone Programming section for

procedures.

*53

SESCOA/Radionics Select

0 = Radionics (0-9, B-F); 1 = SESCOA (0-9 only)

Select SESCOA or Radionics format.

Select 0 for all other formats.

4-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

System Status Report Codes

*60

Trouble Report Code

(0 = no report; 1-F = see description above *59

Sent if a zone has a trouble condition. See UL System

Reporting Note above *59.

Zone report codes are programmed using interactive

56 or 58 Zone Programming modes, while system

status (non-alarm) codes and restore codes are entered

in data fields *59 - *68, *70 - *76, *89. The actual report

code digits that you enter depend upon the particular

installation, and should agree with the Central Station

office receiving the signals.

✱

*61

Bypass Report Code

0 = no report; 1-F = see description above *59

Sent when a zone is manually bypassed. See UL

System Reporting Note above *59.

3+1 or 4+1 Standard Format: Enter a code in the

first box: 1–9, A, B, C, D, E, or F. Enter #+10 for A (this

reports a 0 on some receivers), #+11 for B, #+12 for C,

#+13 for D, #+14 for E, #+15 for F.

*62

AC Loss Report Code

0 = no report; 1-F = see description above *59

Timing of this report is random with up to a 4-hour

delay. If AC restores before the report goes out, there

is no “AC RESTORE” report. See UL System Reporting

Note above *59.

An entry of 0 in the first box disables a report.

Entering 0 in the second box advance to the next field.

Expanded or 4+2 Format: Enter codes in both boxes

(first/second digits) for 1–9 or A–F, as described above.

A 0 in the first box disables a report. A 0 in the second

box eliminates the expanded message for that report.

ADEMCO Contact ID® Reporting: Enter a digit in

the first box to enable the zone to report. Use a

different digit for each zone until you have used up

available digits. If the number of zones exceeds the

number of available digits, begin with digit 1 again.

This is an “enabling” code only and is not the actual

code sent to the Central Station office. Entries in the

second boxes are ignored. An entry of 0 in the first box

disables the report.

*63

Low Bat Report Code

0 = no report; 1-F = see description above *59

Sent when the system’s backup battery has a low-battery

condition. See UL System Reporting Note above *59.

*64

Test Report Code

0 = no report; 1-F = see description above *59

Sent periodically to test that the communicator and

phone lines are operational. See System Reporting UL

Note above *59. Frequency of report is set in Scheduling

mode (event 11) or by the following key commands:

installer code + [#] + 0 + 0 = test report sent every 24 hrs

installer code + [#] + 0 + 1 = test report sent once per week

installer code + [#] + 0 + 2 = test report sent every 28 days

Each of these modes sets schedule 32 (VISTA-20P) or 8

(VISTA-15P) to the selected repeat option; first test

report sent 12 hours after command†.

Report codes are required in fields *61, *65, *71, *72,

for UL Commercial Burglar Alarm installations.

Report codes are required in fields *60, *62, *63, *64, *70, *73,

*74, *75, *76, for UL Commercial Burglar Alarm installations

and required for Residential Fire Alarm installations.

† NOTE: Make sure the Real-Time Clock is set to the proper

time before entering the test report schedule command to

ensure that test reports are sent when expected. (see Setting

the Real-Time Clock section)

*59

Exit Error Report Code

0 = no report; 1-F = see description above

*65

V20PSIA/V15PSIA: [1] Always enabled. Also see field *69.

Open Report Code

0 = no report; 1-F = see description above *59

After arming the system, entry/exit and interior zones

remaining open after exit delay expires cause an alarm

sound at the keypad and external sounder (keypad also

displays “EXIT ALARM”), and entry delay begins.

Disarming before the end of the entry delay stops the

alarm sounding and no message is sent to the central

station. The keypad will display “CA” (fixed-word) or

“ALARM CANCELED” (alpha display).

Sent upon disarming the system in the selected

partitions. See UL System Reporting Note above *59.

*66

Arm Away/Stay Report Code

0 = no report; 1-F = see description above *59

This option allows for independent programming of

Away and Stay reports for each partition, including the

common lobby.

If the system is not disarmed before entry delay expires,

an “EXIT ALARM” message (V20PSIA/V15PSIA: also

zone alarm message) will be sent to the central station.

The keypad will display “EA” (fixed-word ) or “EXIT

ALARM” (alpha display), and alarm sounding continues

until the system is disarmed (or timeout occurs).

An Exit Alarm condition will also result if a fault occurs

in an exit or interior zone within 2 minutes following

the end of the exit delay, and an “EXIT ALARM”

message will be sent to the central station (except for

V20PSIA/V15PSIA, see field *69 Recent Closing

report). With Contact ID format, the message will

contain the zone number and error code 374

(“ALARM–EXIT ERROR”).

NOTE: “OPEN” reports are not sent if the associated

closing report is not enabled.

*67

RF Trans. Low Batt. Report Code

0 = no report; 1-F = see description above *59

Sent when a transmitter low-battery condition exists.

UL installations: must be enabled if wireless devices

are used.

*68

Cancel Report Code

0 = no report; 1-F = see description above *59

Sent upon disarming the system after an alarm

condition was reported.

V20PSIA/V15PSIA: [10] Report enabled.

4-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Programming

Output Device Mapping Menu Mode

Use this menu mode to enter output devices/powerline

carrier devices into the system. See Output Device

Programming section for procedures.

*79

*69

Recent Closing Report V20PSIA/V15PSIA only

Always enabled. Field does not apply to other controls.

Similar to the Exit Error condition described in field

*59, but occurs if an entry/exit door or interior zone is

faulted within two minutes after the initial exit delay

expires. Disarming the system within the two minutes

stops the alarm sound and displays "ALARM

*80

Output Programming Menu Mode

Use this menu mode to define output functions for use

with output devices/powerline carrier devices. See

Output Programming section for procedures.

CANCELED " or "CA" and the faulted zone number.

No message is sent to the Central Monitoring Station.

If the system is not disarmed within two minutes, the

alarm sound continues and a “recent closing” and a

“zone alarm” message are sent to the Central

*81

Zone List Programming Menu Mode

Use the menu mode to define zone lists. See Zone List

Programming section.

*82

Alpha Descriptor Programming Menu Mode

Use this menu mode to assign alpha descriptors to

zones and/or create partition descriptors (VISTA-20P).

Monitoring Station (after dial delay expires).

*70

Alarm Restore Report Code

0 = no report; 1-F = see description above *59

*84

Auto-Stay Arm

Sent when an alarm zone is restored to non-faulted

state. See UL System Reporting Note above *59.

0 = no; 1 = partition 1 only; 2 = part. 2 only; 3 = both parts.

If enabled, the system will automatically change

AWAY mode to STAY mode if the entry/exit door is

not opened and closed within the exit delay time after

a user arms in AWAY mode from a wired keypad (non-

RF device). An Opening report followed by an Armed

Stay report is sent to the Central Station.

*71

Trouble Restore Report Code

0 = no report; 1-F = see description above *59

Sent when a trouble in a zone is restored. See UL

System Reporting Note above *59.

*72

Bypass Restore Report Code

0 = no report; 1-F = see description above *59

Sent when zone that has been bypassed is

unbypassed. See UL System Reporting Note above *59.

If the door is opened and closed within the exit delay

period, the system remains in AWAY mode.

Any RF device that arms the system AWAY overrides

this feature and the system remains armed AWAY.

*73

AC Restore Report Code

*85

Cross Zone Timer

0 = 15 secs 4 = 90 secs

1 = 30 secs 5 = 2 min

0 = no report; 1-F = see description above *59

8 = 4 min

9 = 5 min

#+12 = 8 min

#+13 = 10 min

Sent when AC power has been restored after an AC

power outage. See UL System Reporting Note above *59.

2 = 45 secs 6 = 2-1/2 min #+10 = 6 min #+14 = 12 min

3 = 60 secs 7 = 3 min #+11 = 7 min #+15 = 15 min

*74

Low Bat Restore Report Code

0 = no report; 1-F = see description above *59

Sets the maximum amount of time in which two cross

zones must be tripped in an armed system to send an

alarm message to the Central Station. If only one cross

zone is tripped during this time, a trouble message (CID

code 380) for that zone is sent to the Central Station.

Assign cross zone pairs in zone list 4.

Sent when a system low-battery condition is restored

to normal. See UL System Reporting Note above *59.

*75

RF Xmtr Low Batt. Restore Code

0 = no report; 1-F = see description above *59

Sent when a transmitter’s low battery condition is

restored (i.e., new battery installed).

This option not for use in UL installations.

UL: must be enabled if wireless devices are used. See

UL System Reporting Note above *59.

*86

Cancel Verify Keypad Display

0 = no “alarm canceled” display

1 = display “Alarm Canceled” when system is disarmed

after an alarm has occurred. (To clear the “ALARM

CANCELED” display, the user must enter the security

code + OFF again.)

This feature causes a “ALARM CANCELED” display on

the LCD keypad under the following conditions:

• After the kissoff of the cancel message to the Central

Station, indicating a successful transmission.

• When an alarm is successfully canceled before the

Central Station received the Alarm message. E.g., if

an alarm is incorrectly triggered and the user

presses code + OFF before the dial delay time has

expired, the message will never go out to the CS.

*76

Test Restore Report Code

0 = no report; 1-F = see description above *59

This is sent when the Test mode is exited. See UL

System Reporting Note above *59.

Miscellaneous System Fields

*77

Daylight Saving Time Start/End Month

0 = Disabled; 1 = Jan; 2 = Feb; 3 = Mar; 4 = April;

# + 10 = Oct; # + 11 = Nov; # + 12 = Dec

Enter the start and end month for daylight savings

time, if applicable to the region.

*78

Daylight Saving Time Start/End Weekend

0 = disabled; 1 = first; 2 = second; 3 = third; 4 = fourth;

5 = last; 6 = next to last; 7 = third to last

When the Cancel report is not enabled and the

system is disarmed:

•

Enter the start and end weekend for daylight savings

time, if applicable to the region.

a. before dialer delay expires (alarm report not

sent) message “Alarm Canceled” is displayed.

b. after dialer delay expires message “Alarm

Canceled” is not displayed

4-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

*87

*91

Option Selection

Misc. Fault Delay Time

0 = 15 secs 4 = 90 secs 8 = 4 min

1 = 30 secs 5 = 2 min 9 = 5 min

#+12 = 8 min

#+13 = 10 min

0 = none; 4 = using Audio Alarm Verification (AAV) unit;

8 = Enable Exit delay restart/reset ††

2 = 45 secs 6 = 2-1/2 min #+10 = 6 min #+14 = 12 min

3 = 60 secs 7 = 3 min #+11 = 7 min #+15 = 15 min

Select by adding the values of each option. E.g., for both

AAV and Exit delay restart, enter # + 12 (4 + 8).

Used with zones assigned to a configurable zone type

with fault delay on (configurable zone type digit “6”),

and sets a zone response time of 15 seconds to 15 min.

It can be assigned to zones with sensors that provide a

trouble indication when an oil tank is low, or similar

applications for critical condition monitoring where a

non-alarm response is desired.

UL: May only be used on non-burglar alarm and non-

fire alarm zones when used on a fire and/or UL burglar

alarm installation.

V20PSIA/V15PSIA: Options: Same as listed above.

Call Waiting Disable: 0 = call waiting not used

1 = call waiting disable digits (*70) entered in field *40;

(when selected, the system dials the entry in field *40 only

on alternate dial attempts; this allows proper dialing in the

event call waiting service is later canceled by the user).

††“Exit Delay Restart/reset” option allows use of the [∗] key to restart

the exit delay at any time when the system is armed STAY or

INSTANT. This feature also enables automatic exit delay reset, which

resets exit delay if the entry/exit door is re-opened and closed before

exit delay time expires after arming AWAY. Automatic Exit Delay

Reset occurs only once during an armed period.

IMPORTANT: AAV should not be used when Paging or Alarm

Reports are sent to a secondary number unless the monitoring

zone option is used (which pauses calls). Otherwise, the call to

the secondary number by the communicator after the alarm

report will prevent the AAV from taking control of the telephone

line, and the AAV “Listen in” session cannot take place.

*88

Program Mode Lockout Options

0 = standard *98 installer code lockout

1 = lockout [∗] + [#] reentry after *98 exit (reentry via

installer code only)

2 = not used; 3 = lockout all local programming after *98

exit (reentry via downloader only)

The following table summarizes the Program mode

lockout options:

UL installations using the AAV feature must use the

ADEMCO UVCM module (part of the ADEMCO UVS system).

Exit Delay Restart/Reset must be disabled.

Exit

*88

Reentry By:

Command Entry Installer Power-up† Downloader

SIA Guidelines: Exit delay should be enabled.

*99

*98

n/a

yes

*92

Phone Line Monitor Enable

yes

Entry 1–Timeout:

0 = disabled; 1-15 = 1 minute to 15 minutes respectively

(2 = 2 min, 3 = 3 min, etc.; # + 10 =10 min, # + 11 = 11 min,

# + 12 = 12 min, # + 13 = 13 min, # + 14 = 14 min, # + 15 = 15 min)

Entry 2–Display/Sound:

0 = keypad display only when phone line is faulted.

1 = keypad display plus keypad trouble sound when line is

faulted. Each partition turns off its own trouble sound. No

automatic timeout.

2 = Same as “1” plus programmed output device STARTS.

If either partition is armed, external sounder activates.

External sounder will be turned off by normal bell timeout, or

by security code plus OFF from either partition (it does not

have to be the one that was armed).

Entry 1: Sets the length of time a phone line fault

must remain after detected before the second digit

option is activated.

† pressing [∗] + [#] within 50 seconds of power up

*89

Event Log Full Report Code

0 = no report; 1-F = see description above *59

If an Event Logging selection is made in field ∗90, a

message can be sent to the central station receiver

when the log is 80% full. If the log becomes full, new

messages overwrite the oldest messages in the log.

*90

Event Log Enables

0 = no event logging; 1 = log Alarm and Restore; 2 = log

Trouble and Restore

4 = log Bypass and Restore; 8 = log Open/Close

x = log combination of events (add value of entries)

This system can record various events in a history log

(VISTA-20P = 100 events; VISTA-15P = 50 events). At

any time, the downloader operator can then upload the

log and view or print out all or selected categories of

the log. The downloader operator can also clear the log.

Event log can also be viewed at an alpha keypad. The

display/printout at the central station will show the

date, time, event, and description of the occurrences.

Data Entry Example: To select Alarm/Alarm Restore”

and “Open/Close”, enter 9 (1+ 8); to select all events,

enter #15.

Entry 2: Selects the desired phone line fault response.

Option 2 may be used even if a relay unit or Powerline

carrier device is not connected to the control.

Programmed Output Device must either be

programmed to be STOPPED in field ∗80 or STOPPED

by entry of [security code] + [#] + 8 + device number.

Partition in ∗80 should be set to “0,” for STOP.

Field *92 must be enabled for fire alarm installations, UL

commercial burglar alarm installations and UL residential

burglar alarm installations.

If the control unit is used on a UL commercial burglar alarm

system which requires 2 methods of remote communication,

then the control unit’s DACT and the other method of signal

transmission must monitor each other against communication

failure and line fault. The fault must be received and

annunciated within 200 seconds of its occurrence.

4-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Programming

*93

*97

Command to Reset System to Factory

No. of Reports In Armed Period per Zone

(Swinger Suppression)

Default Values

0 = unlimited number of reports

Pressing ∗97 resets all data fields to the factory default

values (shown on the Program Form).

IMPORTANT: Do not press ∗97 to load defaults if any

programming has been done previously—data already

programmed into the system will be changed!

1 = 1 report pair per zone per armed period

2 = 2 report pairs per zone per armed period

Selection limits the number of alarm/alarm restore

message pairs per zone sent to the CS in an armed

period.

*98

SIA Guidelines: Must be set for option 1 or 2.

Command to Exit Program Mode (with

installer code lockout)

V20PSIA/V15PSIA:

Report Pairs: 1 = 1 report pair; 2 = 2 report pairs

Unlimited Reports Enable:

0 = restrict reports to the setting in entry 1

1 = unlimited reports for zones listed in zone list 7;

(use zone list 7 to list zones that require unlimited

reporting; these zones ignore the setting in entry 1)

Exits Programming Mode and prevents re-entry by:

Installer Code + [8] + [0] + [0].

To enter the programming mode if 98 was used to

exit, you must first power down the system. Then

power up again, and press [∗] and [#] at the same time,

within 50 seconds of powering up. See field *88 for

other Program mode lockout options.

∗

*94

Download Phone Number

*99

Command to Exit Program Mode

Enter up to 20 digits as follows: 0–9, # +11 for “∗”,

Exits Programming Mode and allows re-entry by:

Installer Code + [ 8] + [0] + [0]

# + 12 for “#”, # + 13 for a pause.

Enter the phone number of the downloading computer.

Do not fill unused spaces. End field by entering ∗. To

clear entries from field, press ∗94∗.

or by: Pressing [∗] and [#] at the same time, within 50

seconds of power-up.

Pager Programming Fields

*95

Ring Count For Downloading

The system can send various reports to several pagers

(VISTA-20P = up to 4; VISTA-15P = up to 2).

0–15 = number of rings before control picks up phone line.

Refer to the chart below and program accordingly.

phone

module machine

yes

To program pager reporting, do the following:

1. Enter the pager phone number(s), preface characters,

and pager report options in data fields *160 - *171:

2. Enable Pager Delay, if desired, in field *172 (delays

alarm reporting for ALL pagers).

3. Make sure appropriate user open/close pager

reports are enabled (see Security Codes, Assigning

Attributes in Section 6. System Communication

and Operation). Users that perform actions in

partition 1 will, if enabled, attempt to report to all

pagers enabled for open/close reporting in partition

1. Users that perform actions in partition 2 will, if

enabled, attempt to report to all pagers enabled for

open/close reporting in partition 2.

4. If using latchkey pager report, define the latchkey

report schedule using Scheduling mode (master

code + [#] [6] [4] then select event type 03). System

must be armed for the Latchkey report to be sent.

5. If using a function key to manually send a message

to a pager, use *57 Function Key Menu mode to

define the key (function 01).

answer

down-

loading Set field ∗95 to…

yes

1-14 (not 0)

higher than number of

rings set on answer

machine (e.g., if ans.

machine is 4 rings, set

this field to 5). This allows

access to the phone

module if the answer

machine is off.

yes

1-14 (not 0)

15 (bypasses answer

machine^†)

yes

1-14

†

NOTE: If “15” is entered to bypass an answering

machine, and a 4285 or 4286 Phone Module is included in

the system, you should note the following:

When calling in from an off-premises phone, the user

should make the initial call, allow 1 or 2 rings only, then

hang up, then call again. The phone module will now seize

the line, and 2 long tones sound, followed by the usual

voice prompt for the access code. If this procedure is not

followed, phone module operation will not be possible.

6. If reporting zone alarms and troubles to a pager,

use *81 Zone List menu mode to assign the zones

†

associated with each pager (zone lists 9-12 ).

† VISTA-20P supports four pagers and partitioning;

VISTA-15P supports two pagers and zone lists 9 and 10

only.

*96

Command to Initialize CSID and Subscriber

Account Number

Use this command, if necessary, to reset all subscriber

account numbers and the internal CSID to the factory

default values.

*160

Pager 1 Phone No.

Enter up to 20 digits.

If entering fewer than 20 digits, exit by pressing [∗] +

next field number. To clear entries, press ∗160∗.

4-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

*161

*167

Pager 3 Characters

Pager 1 Characters

Enter up to 16 characters.

VISTA-20P. Enter up to 16 characters

Up to 16 optional characters may be sent as a prefix to

the 7-digit system status code sent to Pager #1 (if used).

Phone number in field *160 must have been entered. If

fewer than 16 characters, exit by pressing [∗] and next

field number. To clear entries: press ∗161∗.

See field ∗161 for explanation of entries. If fewer than

16 characters, exit by pressing [∗] and next field

number. To clear entries, press ∗167∗.

*168

Pager 3 Report Options

VISTA-20P. See pager 1 reports, field *162, except use

zone list 11

The 16 characters may be composed of the following:

PIN number, Subscriber account number,

∗ (enter # + 11 to send ∗), # (enter # + 12 to send #),

Pause (enter # + 13 to allow a 2-second pause),^†

special character(s) the user may decide to transmit

† Some paging systems require pause(s) before the prefix.

The Pager format for the 7-digit status code is defined

as follows: XXX-YYYY where:

*169

Pager 4 Phone No.

VISTA-20P. Enter up to 20 digits

If entering fewer than 20 digits, exit by pressing [∗] +

next field number. To clear entries, press ∗169∗.

*170

Pager 4 Characters

VISTA-20P. Enter up to 16 characters

XXX = 3-digit event code: 911

Alarm, 811

See field ∗161 for explanation of entries. If fewer than

16 characters, exit by pressing [∗] and next field

number. To clear entries, press ∗170∗.

Trouble, 101 = Opening (disarm), 102 =

Closing (arm AWAY)

YYYY = 4-digit user or zone number (depending on

type of event). The first digit indicates partition (0 =

system, 1 = part 1, 2 = part 2, 3 = common), followed

by the 3-digit user or zone number.

Display Example 1. 9 1 1 – 1 0 0 4 Indicates an alarm

(911) caused by a fault in zone 4 (0004) in part. 1.

Display Example 2. 1 0 2 – 2 0 0 5 Indicates the system

is reporting a closing–system arming (102) by User 5

(0005) in partition 2.

*171

Pager 4 Report Options

VISTA-20P. See pager 1 reports, field *162, except use

zone list 12

*172

Pager Delay Option for Alarms

0 = none; 2 = 2 minutes; 1 = 1 minute; 3 = 3 minutes

This field determines the delay of alarm reports to the

pager. This gives the Central Station enough time to

verify the alarm report that it received, before the

dialer attempts to dial the pager.

*162

Pager 1 Report Options

0 = No reports sent; 1 = Open/close for all users enabled

to page†; 4 = All alarms and troubles

This delay is for ALL pagers in the system

5 = All alarms, troubles, and open/close for all users

enabled to page

Miscellaneous System Fields

12 = Alarms and troubles for zones entered in zone list 9

13 = Alarms and troubles for zones listed in zone list 9

and open/close for all users enabled to page

Enter the types of reports to be sent to Pager 1 for each

partition.

† Reports to pager only when arming (close)/disarming (open)

from a keypad using a security code; auto-arming/disarming,

arming with assigned button, and keyswitch arming do not

send pager messages.

*174

Clean Me Option

0 = disable; 1 = enable

This is a maintenance feature for ESL 2-wire smoke

detectors on Zone 1. If used, this option limits the

number of smoke detectors to a maximum of 10, rather

than 16. To enable the “clean me” feature, a time

response setting of “3” (1.2 seconds) must be entered in

∗56 Zone Programming for zone 1.

*177

Device Duration 1, 2

*163

Pager 2 Phone No.

0 = 15 secs 4 = 90 secs

1 = 30 secs 5 = 2 min

8 = 4 min

9 = 5 min

#+12 = 8 min

#+13 = 10 min

up to 20 digits

If entering fewer than 20 digits, exit by pressing [∗] +

next field number. To clear entries, press ∗163∗.

2 = 45 secs 6 = 2-1/2 min #+10 = 6 min #+14 = 12 min

3 = 60 secs 7 = 3 min #+11 = 7 min #+15 = 15 min

These entries set the duration for output action options

5 (duration 1) and 6 (duration 2) programmed in ∗80

Output Function Programming.

*164

Pager 2 Characters

up to 16 characters

See field ∗161 for explanation of entries. If fewer than

16 characters, exit by pressing [∗] and next field

number. To clear entries, press ∗164∗.

*181

50/60 Hz AC Operation

0 = 60 Hz; 1 = 50 Hz

Select the type of AC power applied to the control

(option is used for Real-Time Clock synchronization)

*165

Pager 2 Report Options

See pager 1 reports, field *162 for entries, except use

zone list 10

*166

Pager 3 Phone No.

VISTA-20P. Enter up to 20 digits

If entering fewer than 20 digits, exit by pressing [∗] +

next field number. To clear entries, press ∗166∗.

4-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Data Field Programming

Configurable Zone Type Options

Auto Restore (entry 2): Faults on zones set for this option

are cleared; restore messages sent upon restoral of faults.

Configurable Zone Type Fields

• The system allows you to define custom zone types

(VISTA-20P supports 4 [types 90-93]; VISTA-15P

supports 2 [types 90, 91]), based on the options

described at right.

• All configurable zone types can be programmed via

the downloader.

Vent Zone (entry 2): Zones set for this option are ignored if

faulted when arming the system, but are protected if the zone

is later restored (e.g., an open window can be ignored when

arming, but if the window is later closed, it will be protected;

opening the window again causes an alarm.)

• Configurable zone types 90 and 91 can also be

programmed from a keypad using data fields *182-*185.

UL installations: Do not configure zones as fire alarm

or UL burglar alarm zones.

Bypass Disarmed (entry 4): Zones set for this option can be

bypassed only while the system is disarmed.

Bypass Armed (entry 4): Zones set for this option can be

bypassed when the system is armed or disarmed.

Dial Delay (entry 6): Alarms on zones set for this option

participate in dial delay central station reporting, if system

dial delay enabled in field *50.

*182

Configurable Zone Type 90

0-15 = values for each of 10 entries (0-9, # + 10 = 10,

# + 11 = 11, # + 12 = 12, # + 13 = 13, # + 14 = 14, # + 15 = 15)

Enter the appropriate value for each entry, 1-10, based

Fault Delay (entry 6): Faults on zones set for this option are

delayed by the time set in field *87. Do not use this option if

using entry/exit delay for this zone type.

on the charts on the next page.

To calculate the value

for each entry, add the values of the selected options in

each of the entry’s columns shown in the respective

chart (one option per column). For example, to program

entry 2 for “alarm response to short,” “auto restore on,”

but not a “vent zone,” enter 5 (“1” for alarm short + “4”

for auto restore-yes + “0” for vent zone-no).

Faults Display (entry 7): Selects how faults on zones set for

this zone type are displayed.

Power Reset/Verification(entry 7): Selects whether the

system resets power (when user enters code + OFF), and

whether the system performs alarm verification (see

description for zone type 16 in Programming Overview

section) when a fault occurs on these zones.

*183

Zone Type 90 Report Codes

Use Entry Delay (entry 8): Selects whether to use the

system’s entry delay times.

90 ALARM ID: XXX

TROUBLE ID: XXX

Use Exit Delay (entry 8): Selects whether to use the system’s

exit delay time.

Enter the desired 3-digit Contact ID® report codes for

alarms and troubles occurring on zones assigned to

this zone type. Use existing Contact ID® codes, if

appropriate, or define unique codes in CID code range

750-789. Press [∗] to accept and continue.

Interior Type (entry 8): Zones set for this option are treated

same as standard zone type 4 (bypasses when armed STAY,

faults displayed).

Alarm Sounds (entry 9): Selects the type of alarms sound for

zones set for this zone type.

Important Notice on Report Codes: To avoid

confusion at the central station, it is recommended

that existing Contact ID® codes be used with

configurable zone types whenever possible. See list in

System Communication section and/or check with

the central station for a complete list of Contact ID®

report codes. If none of the codes are suitable, choose a

code in the reserved range of 750-789 and make sure to

define the code with your central station.

Bell Timeout (entry 9): Alarm sounding on zones set for this

option remain for the duration set in fields *32 / *33.

Fire Zone (entry 9): Zones set for this option respond in the

same manner as if programmed for zone type 9. Do not set

fire zones to respond as a “fault” in entries 1-6.

Trouble Sounds (entry 10): Selects the type of trouble

sounds for zones set for this zone type (periodic beeps = once

every 30 seconds; trouble beeps = rapid beeping).

Chime Enable (entry 10): Zones set for this option cause a

chime when Chime mode is on.

*184

Configurable Zone Type 91

0-15 = values for each of 10 entries (see field *182 for

explanation of entries.)

*185

Zone Type 91 Report Codes

91 ALARM ID: XXX

TROUBLE ID: XXX

See field *183 for explanation of

entries and read the Important

notice on using these codes.

4-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Configurable Zone Type Charts

ENTRY 1

ENTRY 2

Response when system disarmed and zone is:

Auto

Restore

Vent Zone

Intact EOL

RF zone normal

0 = normal

1 = alarm

Open

RF zone N/A

0 = normal

4 = alarm

Shorted

RF zn off-normal

0 = normal

1 = alarm

INTACT

EOL

OPEN

SHORTED

0 = no

4 = yes

0 = no

8 = yes

ZONE-003-V0

2 = trouble

3 = fault

8 = trouble

12 = fault

see note 5

2 = trouble

3 = fault

see note 6

Zone Conditions Represented

in Entries 1-6

Entry 1 = EOL + Open

Entry 2 = Short + auto restore + vent zone

Configurable Zone Type Notes

ENTRY 3

Response when armed STAY and zone is:

ENTRY 4

1. Do not use the “fault delay” option

with a configurable zone type if it

is set for an entry or exit delay,

otherwise unpredictable results

may occur.

Byp. when

disarmed

Byp. when

armed

Intact EOL

RF zone normal

Open

Shorted

RF zn off-normal

RF zone N/A

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = normal

4 = alarm

8 = trouble

12 = fault

see note 5

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = no

4 = yes

0 = no

8 = yes

2. To create an interior type zone,

select “respond as interior zone

type” (entry 8, interior type = yes),

and set zone response to “fault” in

entries 3-4 to ensure fault

see note 6

Entry 3 = EOL + Open

Entry 4 = Short + byp. disarmed + byp. armed

ENTRY 5

Response when armed AWAY and zone is:

ENTRY 6

displays; do not set as “normal,”

“alarm,” or “trouble.”

Dial Delay

Fault Delay

(see field *50) (see field *87)

Intact EOL

RF zone normal

0 = normal

1 = alarm

2 = trouble

3 = fault

Open

RF zone N/A

0 = normal

4 = alarm

8 = trouble

12 = fault

Shorted

RF zn off-normal

0 = normal

1 = alarm

3. Do not set fire zones to respond as

a “fault” (entries 1-6), otherwise

faults will not display unless the

[∗] key is pressed.

0 = no

4 = use delay

0 = no

8 = use delay

2 = trouble

3 = fault

see note 1

see note 5

Entry 5 = EOL + Open

see note 6

Entry 6 = Short + dial delay + fault delay

4. 4219/4229 modules must use

EOLRs or unpredictable results

may occur.

ENTRY 7

ENTRY 8

Display Faults

Power Reset/

Verification

Use Entry

Use Exit

Delay

0 = no

4 = use exit

delay

Respond as

Interior Type

0 = no

5. RF Zones: The “open” options in

entries 1, 3, and 5 are not

applicable for RF zones. Use the

“intact EOL” option for normal RF

zone conditions and “shorted” for

off-normal RF zone conditions.

Delay 1/2

0 = show alarms 0 = no

0 = no

1 = delay 1

2 = delay 2

when armed 4 = power reset

8 = yes

& disarmed

1 = don’t show

alarms when

after fault

(with code +

OFF)

see note 2

12 = verification

armed (show

alarms, trbles,

faults when

6. a. Zone-Doubling/Double-

Balanced: A short on either

zone of a zone-doubled pair or

on a double-balanced zone

causes a tamper condition.

b. For double-balanced zones, this

entry must be “0”.

c. For zone-doubled zones, both

zones of the doubled pair must

be assigned the same response

to a short.

(see zone

type 16)

disarmed)

3 = never show

any alarms,

trbles, faults

Entry 7 = fault display + power

reset/verification

Entry 8 = entry delay 1/entry delay 2 + exit delay +

interior zone type

ENTRY 9

Alarm Sounds

ENTRY 10

Use Bell

Timeout

Respond as

Fire Zone

Trouble

Sounds

Chime when Chime

Mode On

0 = none

1 = steady

keypad

2 = steady bell see fields *32,

and keypad *33

3 = pulsing bell

0 = no

4 = yes

0 = no

8 = yes

0 = none

1 = periodic

beep

2 = trouble

beeps

0 = no

4 = yes

see zone type

09; see note 4

and keypad

Entry 9 = alarm sounds + bell timeout + fire zone

Entry 10 = trouble sounds + chime

4-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Touch Screen Keypad (AUI) Enable

*191

Keypad 3 Device Address 18

See field *190 for entries and explanation.

The system supports up to two touch screen style

keypads (e.g., Symphony Advanced User Interface

(AUI), and 6270 Touch Screen keypad. NOTE: Use of

touch screen devices does not affect the number of

standard keypads supported.

*192

Keypad 4 Device Address 19

See field *190 for entries and explanation.

*193

Keypad 5 Device Address 20

See field *190 for entries and explanation.

*189

AUI Device 1 and 2 Enable

VISTA-20P: Enter each touch screen (AUI) device’s

home partition.

*194

Keypad 6 Device Address 21

See field *190 for entries and explanation.

0 = disabled; 1 = partition 1; 2 = partition 2; 3 = common

VISTA-15P: 0 = disabled; 1 = enabled

*195

Keypad 7 Device Address 22

See field *190 for entries and explanation.

Set AUI 1 address to 1. Set AUI 2 address to 2.

AUI Compatibility Note: To ensure proper AUI device

operation, connect only to controls having microprocessor

version 3.0 or higher, and use AUI devices with the following

rev levels: 6270 series use version 1.0.9 or higher; 8132/8142

(Symphony) series use version 1.1.175 or higher.

*196

Keypad 8 Device Address 23

See field *190 for entries and explanation.

*197

Exit Time Display Interval

0 = no display; 1-5 = seconds between display updates

If enabled, keypads display the exit time remaining

after arming the system, updated at the interval

selected (i.e. if the exit delay is 30 seconds and “2” is

selected in this field, the keypad display refreshes every

2 seconds, displaying 30, 28, 26, 24, etc.).

An interval greater than “1” may be necessary for some

older keypads to allow users time to enter key presses

between display updates.

Keypad Programming Fields

To enable keypads:

1. Set desired address at keypad (refer to keypad’s

instructions for setting the address).

2. Use data field program mode to enable keypad

addresses, assign a partition, enable sound options

in fields *190-*196 as shown in the table above.

3. If desired, use data field *198 to turn on the display

of the partition number.

4. Set the following keypad-related data fields as

required by the installation:

*21 Quick Arm Enable, *23 Forced Bypass, *84

Auto STAY Arm

5. If using touch screen devices (AUI), enable each

unit in field *189 and set AUI 1 to address 1, AUI 2

to address 2.

FIXED-WORD KEYPAD NOTE: If using 2-digit

display keypads (e.g. 6150RF), do not use exit times

greater than the 96-second delay option. Using a longer

delay time may cause end-user confusion because 2-digit

display keypads cannot display times greater than “99.”

If longer exit time is required by the installation, it is

recommended that the Exit Time Display option be

disabled (“0”).

*198

Display Partition Number

NOTE: Each keypad must be assigned a unique

address, starting at address 16 (address 16 is

reserved for keypad 1, which is automatically set to

partition 1 with all sounds enabled). Keypads

programmed with the same address will give

unpredictable results.

VISTA-20P. 0 = no; 1 = yes

If selected, the partition number is displayed in the

upper-left corner of the display. This is useful when

using the GOTO partition function.

*199

ECP Fail Display

0 = 3-digit display (“1” + device address)

1 = 2-digit fixed-display as “91”

*190

Keypad 2 Device Address 17

Select “0” if using Alpha keypads and/or 3-digit Fixed-

Word Display keypads. ECP faults will display “1” plus

the device address (00-30) of device causing the fault

(e.g., faults on device 07 display as “107”).

Select “1” if using 2-digit Fixed-Word Display keypads

(e.g., certain 6128 series keypads). If selected, ECP

faults for all devices will display as “91” on 2-digit

displays, and “191” on 3-digit or Alpha keypads.

Entry 1 – Partition Assignment:

0 = keypad disabled

1 = partition 1 (VISTA-20P)/keypad enabled (VISTA-15P)

2 = partition 2; 3 = common

Entry 2 – Sound Option:

0 = no suppression

1 = suppress arm/disarm and E/E/ beeps

2 = suppress chime beeps only

3 = suppress arm/disarm, E/E/ beeps and chime beeps

Entry 1: For VISTA-20P, enter the partition in which

the keypad is located; for VISTA-15P, enter 1 to

enable, or 0 to disable the keypad.

Entry 2: Enter the desired sound option for this

keypad.

4-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

4-12

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Menu Mode Programming

Zones and Partitions

Each protection zone needs to be programmed with various attributes using *56 Zone Programming mode

✱

or 58 Expert Programming Mode.

The VISTA-20P system can control two independent areas of protection (known as partitions) for use by

independent users, if desired, by simply assigning zones to one or the other partition during zone

programming. The VISTA-20P, by default, automatically distributes users between the two partitions. The

master user can change the user number distributions.

Zones can also be assigned to a common partition, which is an area shared by users of both partitions (such

as a lobby in a building). This allows either partition to arm, while leaving the common partition disarmed

for access into the other partition. The following describes the functioning of the VISTA-20P common

partition:

• The common zone sounds and reports alarms only when both partitions are armed. If only one partition

is armed, the system ignores faults on the common zone.

• Either partition may arm its system if the common zone is faulted, but once armed, the other partition

will not be able to arm unless the common zone is first bypassed or the fault is corrected.

• Faults on the common zone are displayed on common zone keypads, and will also appear on another

partition’s keypad when that partition is armed.

• Either partition can clear and restore the common zone after an alarm.

About Zone Programming (∗56 and ∗58 Menu Modes)

• Used to program zones, zone types, report codes, enroll 5800 RF Wireless Transmitter serial numbers,

and identify the type of loop input device(s).

• Can also be used to enter alpha descriptors for programmed zones; however, we recommend entering

✱

descriptors in menu mode 82 (Alpha Descriptor Programming after all zone programming has been

completed).

• *58 Expert Programming mode provides a faster method of zone programming than *56 Menu mode, but

is recommended only for those who have had previous experience in programming controls of this type.

NOTE: Alpha display prompts are shown in a double-line box.

✱56 Zone Programming Procedure

1. Enter the zone number to be programmed.

2. Make appropriate entries at the prompts.

3. Confirm the serial number of wireless transmitter zones.

✱

Start Zone Programming mode by pressing 56 while in Data Programming mode.

Set to Confirm

0 = no; 1 = yes

SET TO CONFIRM?

0 = NO 1 = YES

If 1 (Yes) is entered, you will be prompted to confirm each transmitter after entering the

serial and loop numbers (at the “XMIT TO CONFIRM” prompt later in this procedure). We

recommend that you confirm the programming of every transmitter.

5-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Zone Number

Enter Zn Num.

(00 = Quit)

VISTA-20P: wired 01-08 (and 09-48†); wireless 09-48; RF button zones 49-64

VISTA-15P: wired 01-06 (and 07-22†); wireless 09-34; RF button zones 49-56

Both Controls: 91 = addr. device report enable; 92 = duress report enable

95, 96, 99 =emerg. zones

[∗] to continue; 00 to quit

† if zone expanders are used.

Enter the zone number that you wish to program. Zone 10 has been entered in the example

display at left.

Enter a report code for zone 91 to enable addressable device reporting.

Enter a report code for zone 92 to enable duress reporting.

95, 96, 99 are emergency (panic) key zones.

Summary Screen

Zn ZT P RC In:

10 00 1 10 RF:

[∗] to continue

A summary display appears.

“IN: L” appears for wireless zones and indicates input type and loop.

“IN: AD” appears for hardwire expansion zones (AW) and indicates the module’s address

(AD), which is based on the zone number.

Zn ZT P RC In: AD

10 00 1 10 AW: 07

“HW: RT” appears for hardwire zones and indicates configuration (EOL, NO, NC, zone

doubling, double-balanced) and response time selection.

Zn ZT P RC HW: RT

10 00 1 10

Zone Type (ZT)

See table below.

10 Zone Type

Perimeter

Each zone must be assigned to a zone type, which defines the way in which the system

responds to faults in that zone. Enter the Zone Type code from the list below:

Note: If 00 is entered, Delete Zone ? will be displayed.

00 = Not used

07 = 24-Hr Audible

08 = 24-Hr Aux

09 = Fire

10 = Interior w/Delay

12 = Monitor Zone

14 = Carbon Monoxide

16 = Fire w/Verify

20 = Arm–STAY*

21 = Arm–AWAY*

22 = Disarm*

23 = No Alarm Resp

24 = Silent Burglary

77 = Keyswitch

01 = Entry/exit #1

02 = Entry/exit #2

03 = Perimeter

04 = Interior Follower

05 = Day/Night

06 = 24-Hr Silent

*5800 button-type transmitters only

81 = AAV Mon. Zone

90-91 = Configurable

Partition No. (P) (VISTA-20P)

10 Partition

1-3 = partition (3 = common); [∗] to continue

Enter the Partition number for this zone. Partition 1 is shown entered.

Report Code (RC)

10 Report Code

1st 01 2nd 00 10

First Digit: 1-9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F

00 to disable

Second Digit: same as above; [∗] to continue

Enter the report code for this zone, which consists of 2 hexadecimal digits, each in turn

consisting of 2 numerical digits. For example, for a report code of “10,” enter 01 and 00.

For Contact ID®, entering any non-zero entry as the first digit enables the report code for

this zone. Refer to the System Communication section for information about report codes

and formats.

Hardwire Type

02 HARDWIRE TYPE

EOL

0 = EOL; 1 = NC; 2 = NO; 3 = zn doubling (ZD) ^†;4 = dble-balanced (DB)^†

[∗] to continue

† VISTA-20P

This prompt appears only for zone numbers 02-08.

Zone 1 is automatically set for EOL operation.

Response Time (RT)

02 Response Time

0 = 10mSec; 1 = 350mSec; 2 = 700mSec; 3 = 1.2 seconds; [∗] to continue

This prompt appears only for hard-wired zones 01-08 (zone 02 is the display shown).

Option 3: used for “clean me” option on zone 1 (see field ∗174).

NOTE: If zone doubling is being used, the response time selected for zones 02-08

automatically applies to each zone’s associated doubled zone.

5-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

Input Device type (In)

10 INPUT TYPE

RF TRANS

2 = AW (Aux wired zone)

3 = RF (supervised RF transmitter

4 = UR (unsupervised RF transmitter)

5 = Button type RF transmitter (unsupervised).

[∗] to continue

This prompt is skipped for zones 2-8, or 2-16 if zone-doubling was enabled at “Hardwire

Type” prompt.

All of the RF transmitters have one or more unique factory-assigned input (loop) ID codes.

Each of the inputs requires its own programming zone (e.g., a 5804's four inputs require

four programming zones).

RF Transmitters can be enrolled as one of the following types:

Type

Description

Sends periodic check-in signals, as well as fault, restore, and low-

battery signals. The trans. must stay within receiver's range.

Sends all the signals that the “RF” type does, but the control does

not supervise the check-in signals. The transmitter may therefore be

carried off-premises.

(Supervised RF)

(Unsupervised RF)

(Unsupervised

Button RF)

Sends only fault signals. It will not send a low-battery signal until it

is activated. The transmitter may be carried off-premises.

NOTE:

• For the built-in hardwired zones, the Input Device type is automatically displayed as HW

and cannot be edited.

• To change the input type of a previously programmed wireless device (type RF, UR, BR)

to a wired zone (type AW), you must first delete transmitter’s serial number (see To

Delete A Serial Number prompt on next page)

Serial number Entry and Loop Number Entry

[∗] to continue

Used only when enrolling wireless transmitters.

10 INPUT S/N:

A022-4064

a. Transmit two open/close sequences. If using a button-type transmitter, press and

release the button twice, but wait about 4 seconds before pressing the button the second

time.

b. Manually enter the 7-digit serial number printed on the label of the transmitter. Then

press the [✱] key – the cursor will move to the “L” position. You can edit the loop

number, if necessary. When the loop number is acceptable, press [✱].

c. Press key [C] to copy the serial number previously enrolled (used when programming a

transmitter with several input loops).

Loop Number Change

10 INPUT S/N

A022-4064

[∗] to continue

NOTE: If the [C] key is used to copy the previously enrolled serial number, the cursor will

move to the Loop column (L) with the previous serial number displayed, and display a

highlighted question mark for the loop number.

Enter the loop number and press [✱]. The system will now check for a duplicate serial/loop

number combination.

Enroll Summary

10 INPUT S/N

A022-4064

[∗] to continue

If the serial/loop number combination is not a duplicate in the system, a display showing

the serial number and loop number entry will appear.

Confirmation Option

XMIT TO CONFIRM

[∗] to continue

PRESS ✱ TO SKIP

This prompt will only appear if you answered “Yes” at the first prompt in this section.

The system will enter a confirmation mode so that the operation of the actual programmed

input can be confirmed.

Activate the loop input or button that corresponds to this zone.

5-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

If Serial or Loop Numbers do not match after activating the transmitter

Entd A022-4063 1

Rcvd A022-4064

[∗] to continue

If the serial number transmitted does not match the serial number entered, a display

similar to the one shown appears. If the loop number does not match, it will also be

displayed.

If so, activate the loop input or button on the transmitter once again. If a match is not

obtained (i.e., summary display does not appear), press the [#] key twice and then enter (or

transmit) the correct serial number.

To Delete a Serial No.

10 INPUT S/N:

A000-0000

0 in loop number field = delete serial number; # = undo deletion; [∗] to continue

To delete an existing serial number, enter 0 in the loop number field. The serial number

will change to 0's.

If 0 was entered in error, simply re-enter the loop number or press [#], and the serial

number will return to the display.

Summary Screen

[∗] to continue

Zn ZT RC In: L

10 03 10 RF: 1s

If the serial number transmitted matches the serial number entered, the keypad will

beep 3 times and a summary display will appear, showing that zone's programming.

Note that an “s” indicates that a transmitter’s serial number has been enrolled.

Press [∗] to accept the zone information and continue.

Alpha Descriptors

PROGRAM ALPHA?

0 = no; 1 = yes; [∗] to continue

0 = NO 1 = YES

If you want to program descriptors for zones now, enter 1 (Yes) and refer to the Alpha

Descriptor Programming section for available descriptors.

Next Zone Number

ENTER ZN NUM.

(00 = QUIT) 11

[∗] to continue; 00 = quit

If 0 (No) was entered above, the system will return you to the ENTER ZN NUM. prompt

for the next zone.

When all zones have been programmed, enter 00 to quit.

Completing Zone Programming

• When you have finished programming all zones, test each zone using the system’s TEST mode.

• Do not use the Transmitter ID Sniffer Mode for checking wireless transmitting devices, as it

will only check for transmission of one zone on a particular transmitter, NOT the zones assigned to each

additional loop.

NOTE: Following the successful enrollment of each wireless device, note the device serial number in the

appropriate column on the ENROLLED TRANSMITTERS worksheet in the Programming Form; then

enter the other information (zone number, zone type, loop number, etc.) relevant to that device.

∗58 Expert Programming Mode Procedures

This method is designed for use by installers with previous experience in programming ADEMCO control

panels. This mode is also used to program wireless keys using pre-defined templates.

✱

Start Expert Programming mode by pressing 58 while in Data Programming mode.

Confirm?

SET TO CONFIRM?

0 = no; 1 = yes; [∗] to continue

0 = NO 1 = YES 0

This display appears upon entry into this mode.

The default is 0 (No).

If 1 (Yes) is entered, you will be prompted to confirm each transmitter after entering the

serial and loop numbers (at the “XMIT TO CONFIRM” prompt later).

5-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

Summary Screen

Zn ZT P RC HW: RT

01 09 1 10 EL

01-64 = zone number; [∗] to continue; 00 = quit

OR [D] to go to prompts for wireless key programming templates

A summary screen appears, showing zone 1’s currently programmed values.

Enter the zone number being programmed, then press [∗], which displays a summary

screen for that zone. See next prompt (zone 10 in this example).

Zn ZT P RC IN: L

10 00 1 10 :RF –

If programming a wireless key, press the [D] key then skip to the Wireless Key

Programming Templates section following this section. When [D] is pressed, you can choose

from a series of preset templates for easy programming of wireless key zones.

When all zones have been programmed, press 00 at this prompt to quit this menu mode.

Zone Programming

Zn ZT P RC IN: L

10 00 1 10 RF 1

ZT = see Zone Type chart shown in *56 Menu Mode “Zone Type” prompt

P = partition 1, 2, 3 (common); RC = 1 (send CID report); 0 (no report)

IN = input type; L = loop number

[∗] to continue

A summary screen with the selected zone’s current programming appears.

Begin programming zone information as follows:

• Enter Zone Type (ZT), Partition (P), Report Code (RC), and Input Device Type (IN)*

sequentially, but not the Loop No. (L).

• Use the [A] (Advance) and [B] (Back) keys on the keypad to move the cursor within the

screen.

• Use the [C] key to copy the previous zone’s attributes.

Press [✱] to save the programming and continue to the serial number/loop number prompt.

If needed, you can press the [#] key to back up without saving.

* If HW (hardwired) or AW (Auxiliary) is entered for Input Device Type, the next screen

will be similar to the prompt shown, except that HW or AW will be displayed under “IN”.

If RF, BR, or UR is entered, a prompt for Serial and Loop number will be displayed, as

follows.

Serial number

10 INPUT S/N:

AXXX-XXX

S/N = serial number; L = loop number; [∗] to continue

–

Manually enter the serial number (found on the transmitter label), by typing digits in the

“X” locations, using the [A] (advance) or [B] (back) keys as required. You can also perform

two open and close sequences; for button-type transmitters that means pressing and

releasing the button twice.

NOTE: If you want to copy the previous zone’s serial number, press the [C] key.

Press [✱] to advance to the loop number, then enter loop number.

Press [✱] to accept the existing serial and loop number and continue to the “Confirm”

prompt below. If necessary, press [#] to back up and re-enter or edit the serial number.

To Delete a Serial Number

10 INPUT S/N:

A000-0000

[∗] to continue

To delete an existing serial number, enter 0 in the loop number field. The serial number

will change to all 0's as shown.

If 0 was entered in error, simply re-enter the loop number, and the serial number will

return to the display.

Confirm

[∗] to continue

10 XMIT TO CONFIRM

PRESS ✱ TO SKIP

The prompt to confirm appears. This prompt will only appear if the first prompt after

entering ✱58 was answered “Yes.” To confirm, activate the loop input or button that

corresponds to this zone.

The system checks for duplicate. If a duplicate exists, a long error beep will sound.

Press [#] to back up and re-enter the serial and/or loop number.

5-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

If Serial or Loop Numbers do not match after activating the transmitter

[∗] to continue

If the serial/loop number combination transmitted does not match the serial and loop

number entered, a display similar to the one below will appear. If the loop number does

not match, it will also be displayed. If so, activate the transmitter’s loop input or

button one or more times.

Entd

A022-4063

A022-4064

Rcvd

If a match is still not obtained (i.e., summary display does not appear), press the [#] key

twice and enter the correct loop input or, if correct, press [#] again and then enter the

correct serial number.

Summary Screen

Zn ZT P RC In

If the serial number transmitted matches the serial number entered, the keypad will beep

3 times and a summary display will appear, showing the programmed information for that

zone.

10 03 1 10 RF:1s

Note that an “s” indicates

that a transmitter’s serial

number has been

enrolled.

Press [∗] to begin programming the next zone. See first “Summary Screen” prompt

paragraph on previous page.

To exit this mode, enter 00 at the Summary Screen prompt.

Wireless Key Programming Templates

This procedure programs the wireless keys, but a key is not active for arming/disarming until it is

assigned to a user number (see System Operation section, assigning attributes command).

Enter this mode by pressing the D key while at the *58 Menu mode Summary Screen. The following

prompts appear.

Template Number

TEMPLATE ?

1–3 = 5804 templates; 4–6 = 5804BD templates

1–6

•

Enter Template number 1–6 (see chart on next page).

See the defaults provided for each template in the chart that follows these procedures.

Select from templates. Press [∗] to display template (1 shown selected).

NOTE: If necessary, press [#] to back up and re-enter template number.

Press [#] if you want to return to *58 Menu mode summary screen.

Template Display

01 02 03 04

23 22 21 23

•

When [∗] is pressed, the selected template will be displayed.

Top line of display represents loop numbers; bottom line represents zone type assigned

for each loop.

•

Press [∗] to accept template.

Partition

PARTITION

VISTA-20P. 1 = partition 1; 2 = partition 2; 3 = common partition

•

Enter the partition in which the key is to be active, then press [∗] to continue.

Start Zone Number

•

ENTER START ZONE

The system will search for the highest available consecutive 4-zone group (the four zones

in the case of the 5804 and 5804BD), and display the lowest zone number of the group.

If you want to start at a different zone, enter the zone desired, and press [✱]. If that zone

number is displayed, the system has the required number of consecutive zones available,

beginning with the zone you entered. If not, the system will again display a suggested

zone that can be used.

00 = QUIT

If the required number of consecutive zones is not available at all, the system will display

“00”.

To quit this mode and return to *58 Menu mode, enter 00 at this prompt.

Press [∗] to accept.

•

Serial Number

INPUT S/N

•

Manually enter the serial number printed on the label for the wireless key or press and

release the button to transmit its serial number.

AXXX-XXXX

–

•

Press [∗] to accept the serial number. The system will check for a duplicate.

If necessary, press the [#] key to back up without saving, and re-enter the serial number.

Use the [A] key to move forward within the screen, and the [B] key to move backward.

5-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

Confirm

[∗] to continue

•

XMIT TO CONFIRM

PRESS ✱ TO SKIP

If “Yes” was entered at the SET TO CONFIRM? prompt previously (see first prompt

following entry into the ∗58 Expert Programming Mode), the display on the left will

appear. Confirm serial and loop numbers by activating the wireless key.

IMPORTANT:

When confirmed, the key is not active for arming/disarming until it is assigned to a user

number (using the assigning attributes command, attribute “4”). See System Operation

section for procedure.

Not Confirmed

[∗] to continue

Entd A022-4063

Rcvd A022-4064

If the serial number transmitted does not match the serial number entered, a display

similar to the one shown will appear. If the loop number does not match, it will also be

displayed.

If so, activate the button on the wireless key once again. If a match is not obtained (i.e.,

summary display does not appear), press the [#] key and then enter the correct serial

number.

If the serial number transmitted matches the serial number entered, the keypad will beep

3 times and will return you to the Zone Number prompt to enter the starting zone for the

next wireless key.

Or you can return to *58 Menu mode by pressing 00 at the Zone Number prompt.

NOTE: Following the successful enrollment of each wireless device, remove ONE of the

serial number labels from the device and affix it in the appropriate column on the ZONE

PROGRAMMING worksheet of the Programming Form; then enter the other information

(zone number, zone type, loop number, etc.) relevant to that device.

Wireless Key Predefined Default Templates

LOOP 3

GREEN/YELLOW

LED

LOOP 2

YOU MUST

PROGRAM

THIS BUTTON

LOOP 4

OFF

LOOP 2

LOOP 1

Note:

These transmitters

are not intended for

use in UL

RED/YELLOW

LED

LOOP 4

(YOU MUST

PROGRAM

THIS BUTTON)

LOOP 3

installations.

LOOP 1

•

• •

•

• •

•

ENROLL AS "BR"

5804BD-007-V0

5804-001-V1

5804BD 2-Way Wireless Key

Transmitter

5804 Wireless Key Transmitter

For 5804

For 5804BD

TEMPLATE 1

Loop Function

Zone Type

TEMPLATE 4

Loop

Function

No Response

Arm Away

Disarm

Zone Type

No Response

Disarm

Arm Away

No Response

Function

No Response

Disarm

TEMPLATE 2

TEMPLATE 3

Loop

Zone Type

TEMPLATE 5

TEMPLATE 6

Loop

Function

No Response

Arm Stay

Zone Type

Arm Away

Arm Stay

Function

24-hour audible

Disarm

Arm Away

Disarm

Loop

Zone Type

Loop

Function

24-hour audible

Arm Stay

Arm Away

Disarm

Zone Type

Arm Away

Arm Stay

5-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

About Output Device Programming (*79/*80 Menu Mode)

Output Devices:

The VISTA-20P system supports up to 16 relays and/or Powerline Carrier devices

(X-10 devices) plus 2 built-in trigger outputs in any combination. These 18 “outputs”

are assigned to system-wide output numbers (01-18). Use *79 Menu Mode to assign

output numbers and map them to device addresses.

The VISTA-15P supports 8 relays and 2 built-in trigger outputs (total 10 outputs).

Output Functions: The system also provides installer-defined output functions, which can be assigned to

any of the physical outputs. Therefore, the action of any one of the outputs can be

based on as many of these functions as desired. This lets a single relay or X-10 device

perform many functions.

The controls support up to 48 output functions.

Use *80 Menu Mode to define output functions.

Relays and output devices are not recommended for life safety applications.

✱

NOTE: When navigating the *79 and *80 menus: The [ ] key is used to accept an entry and advance to

the next prompt. The [#] key is used to revert back to the last question to check or change an entry. Press

✱

[ ] to go forward again.

Programming Output Devices

1. Use *79 Menu Mode to assign module and output numbers and map them to device addresses.

NOTE: You must map output devices using *79 Menu Mode before you can use *80 menu Mode.

2. Use *80 Menu Mode to create output definitions, which control the output devices, if desired.

3. Use *81 Zone List Menu mode to define zone lists for use with output devices if the device action is

based on more than one zone.

• To program a device for manual activation (user code + [#] [7] / [#] [8] + 2-digit device number) or for

scheduled automatic activation, simply map the device using *79 Menu mode.

• To program a device to automatically activate upon a system event (or function key), use *79 Menu mode to

map the device, then use *80 Menu mode to define the automated device action.

*79 Menu Mode: Output Device Mapping

Use this menu to assign Relay Module device addresses and specific relay numbers, and Powerline Carrier

unit numbers. The system is based on predefined module addresses for 4204 and 4229 modules. Refer to the

table shown at the “Module Address” prompt on the next page and set the modules’ addresses (via module

DIP switches) accordingly.

The following table shows how these outputs are identified.

Output Identification

This output…

is identified by…

Relays

the Relay Module’s device address and the relay position on that module (i.e. the physical relay

number, 1-4, on that module).

X-10 Device

Built-in Outputs

a house ID (entered in data field *27) and the unit number of the device.

the output number assigned, 17 for Trigger 1 and/or 18 for Trigger 2.

5-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

Start Output Device Mapping by pressing *79 while in Data Programming Mode.

∗79 Menu Mode

Device Output Number

ENTER OUTPUT NO.

01-18 = VISTA-20P relays/X-10; 01-08, 17, 18 = VISTA-15P relays/X-10

[∗] to continue; 00 to quit

00 = QUIT

This is the logical (or reference) relay number as used in the system. Relays and X-10

devices are numbered 01-16; the on-board triggers are numbered 17 and 18 and can be

programmed for inverted output, if required. Use the worksheet on the Programming Form

(printed separately) to organize device numbers.

Output Normally Low (prompt appears only for Triggers 17 and 18)

0 = no (standard default); 1 = yes

[∗] to continue

17 OUT NORM LOW

0 = NO 1 = YES

Selecting 0 (no) sets the output level normally high (default setting).

Selecting 1 (yes) sets the output normally low.

Output Trigger 17 can be used for resetting 4-wire smoke detectors by connecting it to the

negative power terminal of the smoke detector, selecting 1 at this prompt, and setting as

zone type 54, fire zone reset, in *80 Menu mode.

After entry, display returns to Output Number prompt. Use *80 Menu mode to program

the function of the trigger.

Output Type

XX OUTPUT TYPE

DELETE

0 = delete; 1 = relay on 4204/4229 module; 2 = Powerline Carrier device (X-10)

[∗] to continue

Select whether this is a relay or a Powerline Carrier (X-10) device.

If Powerline Carrier is selected, go to “A” prompt.

If relay is selected, skip to “B” prompt.

“A”

Unit Number (prompt appears if X-10 is selected)

01-16 = predefined address

[∗] to continue

Enter the unit code (set at the device) and press [∗].

The system returns to the Output Number prompt.

XX UNIT No.

“B”

Module Address (prompt appears if relay is selected)

07-15 = predefined address

[∗] to continue

XX MODULE ADDR

07-15

Enter the predefined address for this module as listed below. Make sure the module’s DIP

switches are set to the selected address.

Module Addresses

Address Module

† These addresses apply to VISTA-20P only.

1st 4229 (with zones 09-16)

2nd 4229 (with zones 17-24)

3rd 4229 (with zones 25-32)

4th 4229 (with zones 33-40)

5th 4229 (with zones 41-48)

1st 4204

09^†

10^†

11^†

2nd 4204

3rd 4204

4th 4204

14^†

15^†

Relay Position

1-4 = relay position

[∗] to continue

XX REL POSITION

1-4

This is the actual (or physical) relay number with respect to the Relay Module upon which

it is located. For 4204 modules, relay numbers are 1-4. For 4229 modules, relay numbers

are 1-2.

The system returns to the Output Number prompt for programming the next device.

5-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

*80 Menu Mode: Defining Output Functions

Use this mode to program output function definitions (up to 48 functions) that provide automated control of

any of the output devices, based on events occurring on individual zones or zones with certain zone types.

Each output definition is identified by an output function number, and includes the following components:

Output Definition Components

Component

Description

Output Function No. A reference number that defines an output’s characteristics.

Activated By

Event

Determines whether the initiating event occurs on a zone, a zone list, or a zone type.

Event that triggers the output action. Can be an event occurring on a specific zone number or

a zone list, or a specific zone type.

Partition

If the output is activated by zone type, this defines the partition in which the programmed

event is to cause the device action.

Output Action

Defines the action of the relay/X-10 device when the defined event occurs. Can close for 2

seconds, stay closed until reset, continuously pulse (1-second close-open-close-open, etc.),

toggle the device state, or activate for a defined duration (set in data field *177).

Assigns this function to a specific output number (defined in *79 Menu Mode). This is the

output number that will perform this function upon the triggering event. Note that each

defined function is associated with only one output number. This means that if more than one

output device needs to perform this particular function, you need to define another output

function number with the same attributes, but assign the appropriate output number. (i.e.

output devices can be assigned more than one function number, but each function number can

only be assigned a single output number.

Output No.

For example, if you want to pulse a strobe light upon fire alarms on zone 4 using a relay mapped to

output number 2 (as programmed in *79 Menu Mode), program the following in *80 Menu Mode:

Prompt

Entry

Output Funct. #

Activated By:

Enter Zn No.

Output Action

Output Number

01 (assuming this is the first output function)

3 (zone number)

04 (requires 2-digit zone numbers)

3 (continuous pulse)

02 (device mapped in *79 Menu Mode)

Start Output Definition mode by pressing ✱

∗80 Menu Mode

80 while in Data Programming mode.

Output Function No.

Output Funct. #

VISTA-20P: 01-48 = output function number; VISTA-15P: 01-24 = output function number

[∗] to continue; 00 to quit

(00 = Quit)

Enter the output function number to be defined (or 00 to exit).

Summary Screen

[∗] to continue

01 A E P Trig

?00 0 0 – ZL=00

This screen displays a summary of the current output programming (for this example, Zone

List has been selected-this is the default screen).

A = Output Action; E = Triggering event; P = Partition; Trig = Trigger type

NOTE: A question mark in the summary screen indicates that the device number shown

has not been mapped. Use *79 Menu mode to map the device.

Activated By

01 Activated By:

Zone List

0 = delete

1 = zone list (go to “A” prompt)

2 = zone type (go to “B” prompt)

3 = zone number (go to “C” prompt;)

[∗] to continue

Select where the initiating event for this output definition is to occur as follows:

If you enter “0,” the following prompt appears:

Delete?

Press 1 to delete this output definition. The system

0 = NO, 1 = YES

deletes the output function and any previous programming.

5-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

“A”

01 Zn List

Zone List (prompt appears if zone list was selected)

01-08 = zone list; [∗] to continue

Enter the desired zone list number associated with this output number.

NOTE: Do not use pager zone lists 09-12 in output definitions.

Enter the zone list event that will activate this output.

Enter Event

Alarm

0 = restore; 1 = alarm;

2 = fault; 3= trouble

NOTE: For alarm, fault, and trouble, an event on ANY zone in the list activates the output,

but ALL zones in the list must be restored before the output is restored.

✱

Press [ ] to continue and skip to the “Output Action” prompt.

“B”

01 Enter Zn type

Perimeter

Zone Type (prompt appears if zone type was selected)

Enter the desired zone type associated with this output number. See below for a list of

available zone types.

CHOICES FOR ZONE TYPES:

00 = Not Used

01 = Ent/Exit #1

02 = Ent/Exit #2

03 = Perimeter

05 = Day/Night

06 = 24 Hr Silent

07 = 24 Hr Audible

08 = 24 Hr Aux

12 = Monitor Zone

14 = Carbon Monoxide

16 = Fire w/verification

23 = No Alarm Response

24 = Silent Burglary

04 = Interior Follower 09 = Fire

10 = Interior w/Delay 77 = Keyswitch Zone

81 = AAV Monitor Zone

90-91 = Configurable

CHOICES FOR SYSTEM OPERATION:

20 = Arming–Stay

21 = Arming–Away

22 = Disarming

36 = **At Bell Timeout***

38 = Chime

52 = Kissoff

54 = Fire Zone Reset

58 = Duress

39 = Any Fire Alarm

40 = Bypassing

31 = End of Exit Time

60 = AAV

32 = Start of Entry Time 41 = **AC Power Failure

66 = Function Key†

33 = Any Burglary Alarm 42 = **System Battery Low 67 = Bell Fail

43 = Comm. Failure

68 = Telco Line Cut

78 = Keyswitch Red LED

79 = Keyswitch Green LED

** Use 0 (Any) for Partition No. (P) entry.

*** Or at Disarming, whichever occurs earlier.

†

Use *57 Menu Mode to assign the function key (function “07”).

Note: In normal operation mode:

Code + # + 7 + NN Key Entry starts Device NN.

Code + # + 8 + NN Key Entry stops Device NN.

Enter the partition in which this zone type will occur.

01 Partition

Any partition

0 = any partition; 1 = partition 1;

2 = partition 2; 3 = common

✱

Press [ ] to continue and skip to the “Output Action” prompt.

“C”

Zone Number (prompt appears if zone number was selected)

01 Enter Zn No.

Enter the desired zone number associated with this output number.

✱

Press [ ] to continue.

Enter the zone event that will activate this output.

01 Enter Event

Restore

0 = restore; 1 = alarm/fault/trouble

✱

Press [ ] to continue to the “Output Action” prompt

Output Action

01 Output Action

Close for 2 sec

0 = off

4 = Change Device State

5 = Duration 1 (see data field *177)

6 = Duration 2 (see data field *177)

1 = Close for 2 seconds

2 = Stay Closed

3 = Pulse on & off (1 sec ON, 1 sec OFF)

Enter the desired device action as listed above. Press the [ ] key to continue.

✱

5-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Output Number

Enter Output No.

R02

01-16 = VISTA-20P output no.; 01-08 = VISTA-15P output no.; 17-18 = on-board triggers

Enter the device output number (programmed in *79 Menu Mode) you want associated with

this output. Press [ ] to continue.

✱

Summary Screen

02 A E P TRIG

R02 1 1 3 ZL=00

A summary screen appears showing the programmed settings.

✱

Press [ ] to continue.

About Zone Lists (*81 Menu Mode)

Zone lists let you group individual zones for use with certain system actions. The following table shows

the available zone lists and their purposes:

List No. Used for…

Notes

1, 2

general purpose (GP)

• Any list may include any or all of the system's zone

numbers.

chime-by-zone (see field *26 to enable option)

cross zones (see note at right)

night stay zones

general purpose

V20PSIA/V15PSIA: dial delay disable

general purpose

V20PSIA/V15PSIA: unlimited reports

general purpose

• A zone list can be assigned to more than one output relay.

• Zone List 4: When creating zone list 4 for cross zoning,

include only zones assigned to zone types 3, 4, or 5. Do not

include zones that have delays (entry/exit zones, interior

w/delay) or 24-hour zones, as these zone types may produce

unpredictable operation and may not function as intended.

See field *85 for Cross Zone Timer option.

zones that activate Pager 1

zones that activate Pager 2

zones that activate Pager 3 (VISTA-20P)

zones that activate Pager 4 (VISTA-20P)

• Zone List 6: V20PSIA/V15PSIA: See field *50 for Dial Delay

Disable option.

• Zone List 7: V20PSIA/V15PSIA: See field *93 for Unlimited

Reports option.

Zone List Programming

1. Select an appropriate zone list number.

2. Add the desired zone numbers to be included in that list.

Start Zone List Program Mode by pressing ✱ while in Data Programming mode.

*81 Menu Mode

Zone List Number

Zone List No.

01-12 = zone list number; [∗] to continue

(00 = Quit)

✱

Enter the Zone List Number to program (or 00 to quit). Press [ ] to advance.

In the following displays, zone list 01 has been selected for programming.

Zone Number

01 Enter Zn Num.

†

01-64 = zone numbers followed by [∗] to accept each zone; 00 to continue

(00 = Quit)

✱

Enter each zone number to add to the zone list, followed by pressing [ ] (example, 01 ,

✱

02 , 03 ). After all zones are entered, press 00 to continue.

IMPORTANT: Do not include fire zones in zone lists that are used to STOP device actions.

† VISTA-20P = 01-64; VISTA-15P = 01-06, 09-34, 49-56.

Deleting Zone Lists

01 Del Zn List?

0 = No 1 = Yes

0 = don’t delete list; 1 = delete this zone list; [∗] to continue

To delete the zone list, enter 1. All zones in the zone list will be deleted automatically and

the system returns to the Zone List No. prompt.

To save the zone list, enter 0.

Deleting a Zone

01 Delete Zone?

0 = No 1 = Yes

0 = don’t delete zones; 1 = go to next prompt to delete zones; [∗] to continue

To save the zone list, enter 0 and the system returns to the Zone List No. prompt.

To delete a zone or zones in a zone list, enter 1 to continue.

Delete the Zone

01 Zn to Delete?

(00 = Quit)

†

01-64 = zones to be deleted from list followed by [∗] to accept each zone; 00 to continue

Enter each zone to be deleted from the list, followed by [ ]. After all zones to be deleted are

✱

entered, enter 00 to return to the Zone List No. prompt so that another list can be

programmed, if desired.

† VISTA-20P = 01-64; VISTA-15P = 01-06, 09-34, 49-56.

5-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

About Function Keys (*57 Menu Mode)

The system provides the ability to program each of the four keypad function keys to perform one of 12

system operations. The end user can then activate the function by simply pressing and holding the

programmed key for 2 seconds. Typical functions (listed below) include single-button arming, turning lights

on/off, or single-button paging.

To assign emergency key functions (function key option “00”), first program the respective emergency zone

number (95 for “A” key, 96 for “C” key, 99 for “B” key) with the desired zone type using *56 Zone

Programming mode, then use *57 Function Key menu mode to assign the desired key.

To use a function key to activate a relay action (*57 Menu mode key function 07), use *79 Menu mode to map

the output, and use *80 Menu mode to define the output’s action; select system operation type “66.”

To use a function key for a user macro, use *57 menu mode to activate the desired key, then define the

actual macro functions using the user code + [#] + [6] [6] command.

Programming Function Keys

1. Assign the function key number and partition.

2. Select the desired function for that key.

✱

Start Function Key Programming mode by pressing 57 while in Data Programming mode.

Function Key

Press Key to Pgm

OFF

AWAY

TEST

CODE

STAY

Press the desired function key, A-D.

[∗] to continue

0 = Quit

BYPASS

CHECK

MAX

0 = Exit this mode

Press the desired function key (A-D) you

want to program.

NOTE: A key programmed as a function

key is no longer available to be used as

an end-user macro key or panic key.

INSTANT

READY

Partition Numbe

1 = partition 1; 2 = partition 2; 3 = common partition; [∗] to continue

Enter the partition in which the function key is active.

Partition

Define Key Function

Key "A" Func

Zone 95

†

00 = For the Function key selected, the function will be as follows:

If A selected = Zone 95 (emergency key, same as [1] [∗] pair)

If B selected = Zone 99 (emergency key, same as [∗] [#] pair)

If C selected = Zone 96 (emergency key, same as [3] [#] pair)

If D selected = Single-button paging

† System defaults to

these function key

settings.

01 = Single-button paging (sends a 999-9999 message to pager)

02 = Display time

03 = Arm AWAY (reports as User 00 if closing reports are enabled)

04 = Arm STAY (reports as User 00 if closing reports are enabled)

†† Macros 11-12 apply

to VISTA-20P only.

05 = Arm NIGHT-STAY (reports as User 00 if closing reports enabled)

06 = Step Arming (arms STAY, then NIGHT-STAY^†††, then AWAY)

07 = Output Device Command (for device programmed as system operation type 66–function

key in *80 Menu Mode)

††† If Night-Stay zones

are listed in zone list 5.

08 = Communication Test (sends Contact ID code 601)

09 = Macro Key 1 (define macro by user code + [#] [6] [6] command)

10 = Macro Key 2 (define macro by user code + [#] [6] [6] command)

11^††= Macro Key 3 (define macro by user code + [#] [6] [6] command)

12^††= Macro Key 4 (define macro by user code + [#] [6] [6] command)

[∗] to continue

Enter the desired function for this key, 00 to 12, from the options listed. (00 selected for

example display shown at left). Press [∗] to returns to key number prompt with the next

function key letter displayed.

5-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

About Descriptor Programming (*82 Menu Mode)

The system lets you assign zone descriptors for protection zones, keypad panics, and RF receiver supervision

faults. Each description can be composed of a combination of words (up to 3) selected from a vocabulary of

196 words stored in memory (see a following page). In addition, up to 10 installer-defined words can be added

to those already in memory, plus 3 additional words can be assigned as partition descriptors. Thus, when an

alarm or trouble occurs in a zone, an appropriate description for that zone's location can be displayed at the

keypad. Zone descriptors are recommended for systems using Alpha display keypads, and are necessary if a

4285 or 4286VIP Phone Module is used.

✱

NOTE: You can enter zone descriptors when the zone is being defined in 56 Menu mode, but we

✱

recommend you do it using 82 Menu mode.

If using a 4285 or 4286VIP Phone Module, select from those words in the Alpha Vocabulary List shown

in boldface type. The phone module will not provide annunciation of the other words.

If a 4285/4286 Phone Module is added to an existing system, the Alpha descriptors presently in the

system should be reprogrammed, selecting from those words shown in boldface type in the Alpha

Vocabulary List. The phone module will not provide annunciation of any other words.

Programming Zone Descriptors (Menu Mode ∗82)

1. Enter index numbers for up to three words from the Alpha Vocabulary List for each descriptor by

following the prompts.

2. Enter up to ten 10-digit custom words, if desired, which can then be used in descriptors.

When defining descriptors:

Pressing... Does This...

[6]

[8]

Accepts the entered index number and moves the cursor to the next position for a descriptor.

Saves the entered descriptor and moves to the next descriptor.

Start Zone Descriptor Programming mode by pressing *82 while in Data Programming mode.

Program Alpha

Program Alpha ?

0 = no; 1 = yes; [∗] to continue

0=No, 1=Yes 00

The “Program Alpha ?” prompt will appear. Press 1 to continue.

Custom Words

Custom Words ?

0 = no; 1 = yes; [∗] to continue

0=No, 1=Yes 00

The “Custom Words” prompt will appear.

Press 0 to program standard alpha descriptors from the fixed vocabulary. The system will

then automatically display the descriptor for zone 1.

Press 1 to define custom words (described later in “Adding Custom Words” section).

Summary Screen

[∗] to continue

✱

ZN 01

Note that this is a “Summary mode,” and that no entries can be made. Entries can be made

only when the display contains a flashing cursor, which signifies the “Entry mode.”

✱

To exit the Alpha descriptor mode, press + 0 + 0 at the summary display.

Flashing Cursor

[∗] to continue

✱

ZN 01

✱

To delete or change the default descriptor for zone 1, press [ ] plus the same zone number

(01). This will clear that descriptor and allow changes to be made at the flashing cursor.

✱

NOTE: If you do not wish to change the existing descriptor for zone 1, enter [ ] plus the

next zone number for which you wish to enter (or check) a descriptor. A summary display

✱

for that zone will appear. You must then press [ ] plus the same zone number again to

gain access to the entry mode (flashing cursor) for that zone.

First 3-Digit Index No.

see index for entries; [∗] to continue

✱

ZN 01 B ACK

Press [#] plus the 3-digit number for the first word from the Alpha Vocabulary List.

Example: If the descriptor for zone 1 is BACK DOOR. From the list, BACK = 013.

Therefore, you would enter #013. If you accidentally enter the wrong word, simply press [#]

plus the correct 3-digit number for the word you want.

5-14

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

Accept First Word

✱

ZN 01 BACK

6 = save word and go to next word in this descriptor; 8 = save word and go to next zone

Press [6] to accept the selected word and continue to the next word, or press [8] if this is

the only word you are using for the descriptor.

Second 3-Digit Index No.

✱ ZN 01 BACK

D OOR

see index for entries; [∗] to continue

Enter the 3-digit number for the next word. In our example, the word is DOOR, whose

number is “057.” Enter # 0 5 7.

Accept Second Word

✱ ZN 01 BACK

6 = save word and go to last word in this descriptor; 8 = save word and go to next zone

Press [6] to accept the selected word and continue to the next word, or press [8] if these are

the only words you are using for the descriptor.

DOOR

When descriptor is finished, press [8] to save all words in memory.

Summary Screen

✱ ZN 01 BACK

[∗] to continue

DOOR

The flashing cursor will disappear, indicating that the word(s) are stored in memory for

that zone, as shown in the summary display at the left.

✱]

To enter a descriptor for the next zone, press [ plus the desired zone number. The

summary display appears. Repeat the previous steps to enter the descriptor for the zone.

Adding Custom Words (will not be annunciated by 4285/4286 Phone Module)

You can add up to 10 installer-defined words to the built-in vocabulary, which can then be used when

programming zone descriptors. Each of the 10 words can actually consist of a word string of one or more

words, but no more than ten characters can be used for each word or word string.

When adding custom words, the keypad keys perform the following functions:

[4] Moves cursor one space to the left.

[6] Moves cursor one space to the right.

[8] Saves the new word in the system's memory.

1. Select Custom Word mode (enter 1) when the prompt “CUSTOM WORD ?” is displayed.

2. Enter the number (01–10†) of the custom word or word string to be created, corresponding to index

numbers 245 - 254 respectively (for example, if you are creating the first custom word or word-string,

enter 01, for the second, enter 02, etc.). A cursor will now appear at the beginning of the second line.

† or 11, 12, 13 for partition 1, partition 2 and common lobby descriptors respectively. See Assigning Partition Descriptors

paragraph below.

NOTE: Custom words 8, 9, and 10 are “reminder words” that are programmed using Scheduling Mode.

3. Refer to the Character List of letters, numbers, and symbols on a following page.

Press [#], followed by the two-digit entry for the first letter you would like to display (e.g., # 65 for “A”).

The cursor will then move to the right, in position for the next character.

To delete a character, simply enter the SPACE character (#32).

4. Repeat Step 3 to create the desired word(s). Note that the “4” key can be used to move the cursor to the

left, if necessary. Remember, no word or word-string can exceed 10 characters.

5. Press the [8] key to save the custom word(s) and return to the “CUSTOM WORD ?” display.

Repeat Steps 2–5 for other custom words to be entered. To change a custom word, just overwrite it. If no

more are to be entered now, press [0] to return to the Descriptor entry. The custom word(s) will be

automatically added to the built-in vocabulary.

Assigning Partition/Custom Message Descriptors

VISTA-15P: You can create a custom message display that appears on alpha keypads instead of “System

Ready.” To assign a custom message, use word number 11 as described below.

VISTA-20P: You can assign a partition descriptor (up to 16 characters) for each partition plus the common

lobby. The system displays the appropriate partition’s word instead of “DISARMED READY TO ARM.”

Use the same procedure as for adding custom words (described above), but use these word numbers in step 2:

11 = partition 1 ___________________________________________

12 = partition 2 ___________________________________________ (VISTA-20P only)

13 = common lobby ________________________________________ (VISTA-20P only)

Once a custom word is entered in any of these word locations (11-13),

5-15

Download from Www.Somanuals.com. All Manuals Search And Download.

VISTA-20SE Installation Instructions

ALPHA VOCABULARY LIST

(For Entering Zone Descriptors)

000 (Word Space)

• 059 DOWN

• 060 DOWNSTAIRS

061 DRAWER

• 062 DRIVEWAY

• 064 DUCT

– E –

• 065 EAST

066 ELECTRIC

067 EMERGENCY ∗

068 ENTRY

• 069 EQUIPMENT

• 071 EXIT ∗

072 EXTERIOR

– F –

• 073 FACTORY

075 FAMILY

• 076 FATHERS

• 077 FENCE

• 079 FIRE ∗

• 080 FLOOR ∗

081 FLOW

108 LEVEL

• 109 LIBRARY ∗

• 110 LIGHT

111 LINE

• 113 LIVING ∗

• 114 LOADING

115 LOCK

116 LOOP

117 LOW

• 118 LOWER

– M –

• 119 MACHINE

121 MAIDS

122 MAIN ∗

• 123 MASTER ∗

• 125 MEDICAL ∗

126 MEDICINE

128 MONEY

129 MONITOR

• 130 MOTHERS

• 131 MOTION ∗

132 MOTOR

– N –

• 134 NORTH

135 NURSERY

– O –

• 136 OFFICE ∗

• 138 OPEN ∗

139 OPENING

• 140 OUTSIDE

142 OVERHEAD

– P –

• 161 RIGHT

• 162 ROOM ∗

163 ROOF

– S –

164 SAFE

165 SCREEN

166 SENSOR

• 167 SERVICE

• 168 SHED ∗

169 SHOCK

• 217 WINDOW ∗

• 219 WING

220 WIRELESS

– X –

222 XMITTER

– Y –

– A –

• 001 AIR

• 002 ALARM ∗

004 ALLEY

005 AMBUSH

• 006 AREA

• 007 APARTMENT

• 009 ATTIC ∗

010 AUDIO

223 YARD

– Z –

224 ZONE (No.)

• 225 ZONE ∗

• 226

• 227

• 170 SHOP ∗

171 SHORT

– B –

• 012 BABY ∗

• 013 BACK ∗

• 014 BAR

• 016 BASEMENT ∗

• 017 BATHROOM ∗

• 018 BED

• 228 1ST ∗

• 229

• 230 2ND ∗

• 231

• 232 3RD ∗

• 233

• 234 4TH

• 235

• 236 5TH

• 237

• 238 6TH

• 239

• 240 7TH

• 241

• 242 8TH

• 173 SIDE ∗

174 SKYLIGHT

175 SLIDING ∗

• 176 SMOKE ∗

• 178 SONS

• 179 SOUTH

180 SPRINKLER

• 182 STATION

184 STORE

• 019 BEDROOM ∗

020 BELL

• 021 BLOWER

• 022 BOILER

023 BOTTOM

025 BREAK

• 026 BUILDING

– C –

028 CABINET

• 029 CALL

030 CAMERA

031 CAR

082 FOIL

• 185 STORAGE ∗

186 STORY

• 083 FOYER

084 FREEZER

• 085 FRONT ∗

– G –

• 089 GARAGE ∗

• 090 GAS

190 SUPERVISED ∗

191 SUPERVISION

192 SWIMMING

193 SWITCH

– T –

194 TAMPER

196 TELCO

• 243

• 244 9TH

091 GATE

• 092 GLASS

093 GUEST

094 GUN

245 Custom Word #1

246 Custom Word #2

247 Custom Word #3

248 Custom Word #4

249 Custom Word #5

250 Custom Word #6

251 Custom Word #7

252 Custom Word #8

253 Custom Word #9

254 Custom Word #10

033 CASH

034 CCTV

197 TELEPHONE

• 199 TEMPERATURE

200 THERMOSTAT

• 201 TOOL

202 TRANSMITTER

– U –

035 CEILING

036 CELLAR

• 037 CENTRAL

038 CIRCUIT

• 040 CLOSED ∗

• 046 COMPUTER

047 CONTACT

– D –

• 048 DAUGHTERS

049 DELAYED

• 050 DEN ∗

051 DESK

• 052 DETECTOR ∗

• 053 DINING ∗

054 DISCRIMINATOR

055 DISPLAY

• 057 DOOR ∗

– H –

143 PAINTING

• 144 PANIC ∗

145 PASSIVE

• 146 PATIO ∗

147 PERIMETER

• 148 PHONE

150 POINT

• 095 HALL ∗

• 096 HEAT

098 HOLDUP

099 HOUSE

100 INFRARED

• 101 INSIDE ∗

102 INTERIOR

103 INTRUSION

– J –

• 205 UP

• 206 UPPER

• 207 UPSTAIRS ∗

• 208 UTILITY ∗

– V –

151 POLICE ∗

152 POOL ∗

• 153 POWER

– R –

209 VALVE

210 VAULT

212 VOLTAGE

– W –

213 WALL

214 WAREHOUSE

• 216 WEST

104 JEWELRY

– K –

NOTE: Custom words 8,

9, 10 are “reminder

words” that can be

programmed to display

using Scheduling Mode.

155 RADIO

• 105 KITCHEN ∗

–

• 156 REAR

157 RECREATION

159 REFRIGERATION

160 RF

L –

• 106 LAUNDRY ∗

• 107 LEFT

Note:

Bulleted (•) words in boldface type are those that are also available for use by the 4285/4286 Phone Module. If using a

phone module, and words other than these are selected for Alpha descriptors, the phone module will not provide

annunciation of those words.

Italicized words followed by an asterisk indicate those words supported by the 6160V/6150V Voice Keypads

––––––––––––––––––––––––––– CHARACTER (ASCII) CHART –––––––––––––––––––––––––––

(For Adding Custom Words)

32 (space)

)

;

“

–

(

5-16

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Mode Programming

Programming Installer and User Schedules

The system provides schedules, which can be used to automatically control 11 types of system events at pre-

defined times. Some events are reserved for the installer only.

VISTA-20P: Provides up to 32 schedules: 16 schedules for use by the end-user, 16 for use by the installer.

VISTA-15P: Provides up to 8 schedules: 4 schedules for use by the end user, 4 for use by the installer.

Start Scheduling mode by entering installer code + [#] + [6] [4] while in normal operating mode.

NOTE: The master code can only access schedules 01-16 (VISTA-15P = 01-04) and events 00-07.

Schedule Number

ENTER SCHED NO.

VISTA-20P

VISTA-15P

01-04 = end-user schedules

05-08- = installer-only schedules

00=QUIT

01-16 = end-user schedules

17-32 = installer-only schedules

[∗] to continue

Enter the desired schedule number.

Enter Event

ENTER EVENT

00 = clear event

05 = Forced Away Arming^†

06 = Auto Disarm

01 = Relay On/Off

02 = User Access

07 = Display “Reminder”

10 = Display custom words ^††

11 = Periodic Test Report^†††

03 = Latch Key Report to Pager

NOTE: Events 07 and

10 cause the keypad to

beep every 30 seconds

when messages are

displayed. Stop the

beeps by pressing any

key.

04 = Forced Stay Arming^†

Press [∗] to continue

Enter the desired event number for event you want to occur at a specified time.

Events 10-11 are reserved for the installer only.

Latch key report (option 03) is sent to all pagers in the user’s partition and is active only

when the system is armed (message sent is 777-7777). User must be enabled for paging

(see User Attributes in System Operation section).

† Forced bypass is automatically enabled regardless of setting in field *23.

†† If selected, system displays custom words 8, 9, and 10 at defined time. Can be used as

installer’s reminder message to the end user.

††† See key commands in Testing the System section to quickly set periodic test

reporting intervals.

Device Number (For event 01-relay on/off)

DEVICE NUMBER

01-18 = device number; press [∗] to continue

Enter the physical device number as programmed in ∗79 Menu Mode, then press [*] to

continue to the “Start” prompt.

Device numbers 17 and 18 designate built-in triggers 1 and 2 respectively.

Group Number (For event 02-user access)

1-8 = group number; press [∗] to continue to the “Start” prompt

GROUP NUMBER

Partition (For events 03-07, 10)

0 = all partitions; 1 = partition 1; 2 = partition 2; 3 = common

Press [*] to continue to the “Start” prompt.

PARTITION

Start Time

START

SMTWTFS

01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM; Days = place “1” under days

Press [∗] to continue.

HH MMA M 0 0 1 0 0 0 0

Enter the event’s start time and days of the week to occur.

To select days, position the cursor under the desired days using the [∗] key to move

forward, then press “1” to select the day.

5-17

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Stop Time (For events 01-relay on/off; 02-user access; 03-latch key report)

01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM; Days = place “1” under days

Press [∗] to continue.

STOP

SMTWTFS

HH MMA M 0 0 1 0 0 0 0

Enter the event’s stop time and days of the week to occur.

To select days, position the cursor under the desired days using the [∗] key to move

forward, then press “1” to select the day.

Repeat Option

REPEAT OPTION

0 = do not repeat; 1 = repeat weekly; 2 = repeat biweekly (every other week)

3 = repeat every third week; 4 = repeat every fourth week

Press [∗] to continue.

0-4

Enter the desired repeat option for this schedule.

e.g., To make a schedule that happens everyday you would select all days with a repeat

count of 1. To make a schedule that runs for one week then stops, select everyday with a

repeat count of 0.

Randomize (For events 01 and 11)

RANDOMIZE

0=NO 1=YES

0 = no; 1 = yes

Press [∗] to continue.

If selected, the scheduled start and stop times will vary within 60 minutes of the “hour”

time. For example, if a schedule is set to start at 6:15pm, it will do so the first time 6:15pm

arrives, but on subsequent days it will start anytime between 6:00 and 6:59 p.m.

NOTE: Do not use the random option if the start and stop times are within the same “hour”

setting, otherwise unpredictable results may occur (e.g., the randomized stop time may occur

before the start time).

5-18

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

System Communication and Operation

Panel Communication with Central Station

This system accommodates several formats for reporting alarms and other system conditions to the Central

Station. The process of a successful transmission consists of both the method of communication between the

control panel and the Central Station receiver; and the actual way the information is sent and displayed at

the Central Station.

When the panel calls the Central Station receiver, it waits to hear a “handshake” frequency from the receiver

to confirm that the receiver is on-line and ready to receive its message. Once the panel hears the handshake

it is programmed to listen for, it sends its message. The panel then waits for a “kissoff” frequency from the

receiver acknowledging that the message was received and understood.

If the handshake frequency is not given or is not understood by the panel, the panel will not send its

message. Once the handshake frequency is received and understood by the panel, the panel sends its

message. If there is an error in the transmission (the receiver does not receive a “valid” message), the kissoff

frequency is not given by the Central Station receiver.

The panel makes a total of eight attempts to the primary telephone number and eight attempts to the

secondary telephone number (if programmed) to get a valid message through. If the panel is not successful

after its numerous attempts, the keypad displays COMM. FAILURE (on alpha keypads) or FC (on fixed-

word keypads).

Report Code Formats

The following chart indicates the types of (handshake/kissoff) frequencies that the panel supports and the

different formats that can be sent with each.

FORMAT

Low Speed

HANDSHAKE

1400 Hz

TRANSMITS DATA

1900Hz (10PPS)

KISSOFF

1400 Hz

TRANSMIT TIME

Under 15 secs

3+1, 4+1, 4+2

(Standard report)

Sescoa/Rad

3+1, 4+1, 4+2

Express

4+2

2300 Hz

1800Hz (20PPS)

DTMF (10 cps)

2300 Hz

1400 Hz

Under 10 secs

(Standard report)

Under 3 secs

1400–2300 Hz

Contact ID

1400–2300 Hz

DTMF (10 cps)

1400 Hz

Under 3 secs

The following table describes each format in greater detail.

FORMAT TYPE

3+1 and 4+1

Standard Formats

3+1 and 4+1

DESCRIPTION

Comprises a 3- (or 4-) digit subscriber number and a single-digit report

code (e.g., Alarm, Trouble, Restore, Open, Close, etc).

Comprises a 3- (or 4-) digit subscriber number and a two-digit report code.

The first digit is displayed on the first line. On the second line, it is repeated

3 (or 4) times and is followed by the second digit. This is the “expanded”

digit.

Expanded Formats

4+2 Format

ADEMCO Contact ID

Reporting Format

Comprises a 4-digit subscriber number and 2-digit report code.

Comprises a 4- or 10-digit subscriber number (depending on format

selected), 1-digit event qualifier (“new” or “restore”), 3-digit event code, and

3-digit zone number, user number, or system status number (see the

following page).

6-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

The following table lists codes for reports sent in different formats:

Code for

3+1/4+1

Expanded

Type of

Report

3+1/4+1

Standard

Code for

4+2

Alarm

SSS(S) A

SSS(S) T

SSS(S) B

SSS(S) E

SSS(S) A

AAA(A) Z

SSSS AZ

SSSS Tt

SSSS Bb

SSSS EA

Trouble

Bypass

AC Loss

SSS(S) T

TTT(T) t

SSS(S) B

BBB(B) b

SSS(S) E

EEE(E) A

Low Batt

SSS(S) L

SSSS LL

LLL(L) L

Open

Test

SSS(S) O

SSS(S) C

SSS(S) G

SSS(S) R

SSS(S) O

OOO(O) U

SSSS OU

SSSS CU

SSSS Gg

SSSS RZ

SSS(S) C

CCC(C) U

SSS(S) G

GGG(G)g

Restore

Alarm

SSS(S) R

RRR(R) Z

AC Restore

LoBat Res.

Trouble Res.

Bypass Res.

SSS(S) R

SSSSR

R R R (R )A

A A A

SSS(S) R

SSSS R L

L B

R R R (R )L

L L L

SSS(S) R

SSSS R t

R R R (R )t

T T T

SSS(S) R

SSSS R b

R R R (R )b

B B B

Where:

SSS or SSSS = Subscriber ID

C = Close Code–1st Digit

U = User Number (in hex)

A = Alarm Code–1st digit

Z = Typically Zone Number*–2nd digit

Tt = Trouble Code (1st & 2nd digits)

Bb = Bypass Code (1st & 2nd digits)

Gg = Test Code (1st & 2nd digits)

R = Restore Code (Alarm)

R t = Restore Code (Trbl) 1st & 2nd digits

AC Loss Code (1st & 2nd digits)

R b = Restore Code (Byps) 1st & 2nd digits

C =

B =

Low Battery Code (1st & 2nd digits)

R A = Restore Code (AC) 1st & 2nd digits

A C

O = Open Code–1st Digit

R L Restore Code (Bat) 1st & 2nd digits

L B =

*Zone numbers for:✱ & #, or B = 99; 1 + ✱, or A = 95; 3 + #, or C = 96; Duress = 92

6-2

Download from Www.Somanuals.com. All Manuals Search And Download.

System Communication

Ademco Contact ID

The Ademco Contact ID Reporting Format comprises the following:

4-digit or 10-digit subscriber number (depending on format selected).

1-digit event qualifier (“new” or “restore”).

3-digit event code.

2-digit Partition No.

3-digit zone number, user number, or system status number (see the following page).

Ademco Contact ID Reporting takes the following format: CCCC(CCCCCC) Q EEE GG ZZZ

where:

CCCC(CCCCCC) =Customer (subscriber) ID

Q = Event qualifier, where:

E = new event , and R = restore

EEE = Event code (3 hexadecimal digits)

Note: For a complete list of event codes, refer to the central office

receiver manual.

GG = Partition Number (system messages show “00”)

ZZZ = Zone/contact ID number reporting the alarm, or user number for

open/close reports. System status messages (AC Loss, Walk Test, etc.)

contain zeroes in the ZZZ location.

TABLE OF CONTACT ID EVENT CODES

(some event codes may not apply to certain control panels)

Code Definition

110

121

122

123

131

132

134

135

143

145

146

150

162

301

302

305

309

321

333

341

344

351

353

373

374

380

Fire Alarm

Duress

Alarm, 24-hour Silent

Alarm, 24-hour Audible

Alarm, Perimeter

Alarm, Interior

Alarm, Entry/Exit

Alarm, Day/Night

Alarm, Expansion Module

ECP Module cover tamper

Silent Burglary

Alarm, 24-Hour Auxiliary/Monitor zone

Carbon Monoxide

381

382

383

384

393

401

RF Sensor Supervision

Supervision Auxiliary Wire Zone

RF Sensor Tamper

RF Sensor Low-battery

Clean Me

Disarmed, Armed AWAY, Armed

MAXIMUM

Schedule Arm/Disarm AWAY

Cancel by User

Remote Arm/Disarm (Downloading)

Quick Arm AWAY

Keyswitch Arm/Disarm AWAY

Disarmed/Armed STAY/INSTANT,

Quick-Arm STAY/INSTANT

Keyswitch Arm/Disarm STAY

Recent Closing

403

406

407

408

409

441

AC Power

442

459

570

601

602

606

607

623

625

627

628

642

Low System Battery/Battery Test Fail

System Reset (Log only)

Battery Test Failure

Bell/Siren Trouble

Trouble, Expansion Mod. Supervision

Trouble, ECP Cover Tamper

RF Receiver Jam

Telco Line Fault

Long Range Radio Trouble

Fire Loop Trouble

Bypass

Manually Triggered Dialer Test

Periodic Test

AAV to Follow

Walk Test Entered/Exited

Event Log 80% Full

Real-Time Clock was Changed (log only)

Program Mode Entry (log only)

Program Mode Exit (log only)

Latch Key (log only)

Exit Error Alarm

Global Trouble, Trouble Day/Night

750 - Reserved for Configurable Zone Type

789

report codes (check with central station

when using these codes)

6-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

System Security Codes

The systems provides one Installer code, one System Master code, plus a set of other user codes intended

for other users of the system. These codes can each be assigned one of 5 authority levels, which determine

the functions each code can perform as listed in the table below.

VISTA-20P: Provides 48 security codes (plus Installer code), including one System Master code, two

Partition Master codes, and 45 general user codes.

VISTA-15P: Provides 32 security codes (plus Installer code), including one System Master code and 31

general user codes.

Authority Levels (can be assigned to users 03-49 only; users 1 and 2 cannot be changed)

Level

User No.

Functions

Installer

(default=4112) perform all security functions except can disarm only if used to arm; can

enter program mode; can change System Master code; cannot assign any other user

codes

System

Master

(default 1234) only one system master code per system; can perform all security

functions, add/delete users in either partition, change system master code, view event

log, set system clock, program keypad macro, program scheduled events, activate output

devices (triggers/relays)

Partition

Master

(default)

P1 = 03

P2 = 33

VISTA-20P. Same as Master, except add/delete users limited to assigned partition

only, (these users can be assigned different authority levels, if desired; any user can be

assigned the partition master authority level)

0-User

03-49 (V20P) perform security functions (arm, disarm, etc.) only; cannot add/delete users, view event

log, set system clock or program scheduled events

03-33 (V15P)

see “user”

1-Arm Only

2-Guest

arm system only

can disarm the system only if it was used to arm the system

3-Duress

performs security functions, but also silently sends a duress message to the central

station; reports as duress code user number.

4-Partition

Master

see “user”

VISTA-20P. See Partition Master paragraph above; used to assign other user numbers

as partition masters

Refer to the user guide for detailed procedures on adding/deleting security codes and changing user

attributes.

The following is a brief description of how to add user codes.

Changing the System Master code...

Using Installer code: Installer code + [8] + 02 + new code

Using current System Master code: System Master code + [8] + 02 + new code + new code again

Adding a User Code: Master code + [8] + 2-digit user no. + user’s code

Deleting a User Code: Master code + [8] + 2-digit user no. + [#] [0]

Assigning Attributes: Master code + [8] + 2-digit user no. + [#] [attribute no.] + value

Attributes:

Values

1 = Authority Level

2 = Access Group

3 = Active Partition(s)

for this user;

0-4 (see Authority Level table above)

0-8 (0 = not assigned to a group)

1, 2, 3 (common)

Enter partitions consecutively if more than one and press [#] to

end the entries.

4 = RF Zone No.

Assigns user number to button type zone for arm/disarm

(keyfob must be enrolled in system first; see Wireless Key

Templates section).

5 = Open/Close Paging

1 for yes, 0 for no

6-4

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

Keypad Functions

The following is a brief list of system commands. For detailed information concerning system functions,

refer to the User's Manual. For Touch Screen style keypad users, refer to the separate Touch Screen

keypad (AUI) User’s Guide.

Voice Keypads

The 6150V/6160V Voice Keypads provide the following features:

• Message Center, which lets the user record and playback one message.

• Voice Status, which can announce system status by using the STATUS key.

• Voice Chime, which can alert users to the opening of doors/windows while the system is disarmed.

Refer to the User Guide for specific procedures for activating and using these features.

Keypad Commands

Function

Description

Silence alarms

Pressing any key will silence the keypad sounder for 10 seconds. Disarming the system will

silence both keypad and external sounders.

Quick Arm

If enabled (field ∗21), you can press [#] in place of the system's security code, plus the

desired arming key (Away, Stay, Instant, Maximum)

Single-Button arming

If programmed (*57 Function Key menu mode), lettered keys A-D can be used for arming,

using options 3-AWAY, 4-STAY, 5-NIGHT-STAY, or 6-Step-Arming

If used, no security code is required to arm the system.

Alarm Memory

Arming Away

When the system is disarmed, any zones that were in an alarm condition during the armed

period will be displayed. To clear this display, simply repeat the disarm sequence (enter

the security code and press the OFF key) again.

Enter code + AWAY [2] or simply press appropriate lettered key on the keypads (see

“Single-Button Arming” above). If the “Auto-Stay Arm” feature is enabled (field *84) and

the entry/exit door is not opened and closed within the programmed exit delay time, the

system will automatically arm in STAY mode if armed from a wired keypad (non-RF

device). If the door is opened and closed within the exit delay period, the system arms in

AWAY mode.

Arming Stay

Enter code + STAY [3] or simply press appropriate key on the keypads (see “Single-Button

Arming” above). See “Arming Away” above for Auto-Stay arming feature.

Enter code + STAY [3] + STAY [3] or simply press appropriate key on the keypads (see

“Single-Button Arming” above).

Arming Night-Stay

Arming Instant

Enter code + INSTANT [7].

Arming Maximum

Enter code + MAXIMUM [4] or simply press appropriate lettered key on the keypads (see

“Single-Button Arming” above).

Disarming

Enter code + OFF [1]. If entry delay or an alarm is active, you do not need to press

OFF.

Bypassing Zones

Enter code + BYPASS [6] + zone number(s).

Forced (Quick) Bypass

To automatically bypass all faulted zones, use the “Quick Bypass” method. Enter code +

BYPASS + [#], then wait for all open zones to be displayed. Arm when display indicates

“ZONE BYPASSED” and “READY TO ARM”.

Chime Mode

Activate Output

Devices

Enter code + CHIME [9]. To turn chime off, enter code + CHIME again.

If relay outputs (via a 4204, or 4229), or Powerline Carrier devices are used, two keypad

entries available to the user are included. If programmed, these entries can be used to

manually activate or deactivate the device(s) for starting or stopping some action, such as

turning lights on or off, etc. These keypad entries are:

[Security Code] + # + 7 + [2-digit Device #] activates (starts) that device.

[Security Code] + # + 8 + [2-digit Device #] deactivates (stops) that device.

6-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

SUMMARY OF ARMING MODES

Arming Mode

Features for Each Arming Mode

Exit Delay

Yes

Entry Delay

Yes

Perimeter Armed

Interior Armed

AWAY

STAY

Yes

NIGHT-STAY

Yes

only those zones

listed in Night-

Stay zone list

INSTANT

Yes

MAXIMUM

Yes

Panic Keys

There are three Panic keys (A, B, and C) that, if programmed, can be used to manually initiate alarms and

send a report to the central station.

Each key can be programmed for 24-hour Silent, 24-hour Audible, Fire, or Personal Emergency responses.

The programmed Panic response is activated when the appropriate key is pressed for at least 2 seconds.

The Panic keys are identified by the system as follows:

Keys

[A] (∗/1)

[B] (∗/#)

[C] (3/#)

Displayed as Zone

IMPORTANT: For a Silent panic function (if programmed) to be of practical value, you must program a

report code for the zone and the system must be connected to a central station.

Setting the Real-Time Clock

Set the time and date by doing the following:

Alpha Display:

+[#] + [6] [3]

(Security Code)

DISARMED

READY TO ARM

2. Press [∗] when the time/date is displayed.

TIME/DATE

04:04PM 10/17/00

Current time display

SAT

A cursor appears under the first digit of the hour.

To move cursor ahead, press [∗]. To go back, press [#].

• Enter the 2-digit hour setting.

• Enter the 2-digit minute setting.

• Press [1] for PM or [2] for AM.

• Enter the last two digits of the current year.

• Enter the 2-digit month setting.

TIME/DATE

04:04P2000/10/17

Time/date editing display

SAT

• Enter the 2-digit day setting.

3. To exit, press [∗] when cursor is at the last digit, or wait 10 seconds.

6-6

Download from Www.Somanuals.com. All Manuals Search And Download.

System Operation

Various System Trouble Displays

Alpha Display

Fixed Disp.

Meaning

ALARM CANCELED

will appear if an exit or interior zone contained a fault during closing at the

time the Exit Delay ended (e.g., exit door left open), but the system was

disarmed during the Entry Delay time. The alarm sounder and keypad sound

continuously, but stop when the system is disarmed. No message will be

transmitted to the central station.

EXIT ALARM

appears when Exit Delay ends if an exit or interior zone contained a fault

during closing. The alarm sounder and keypad sound continuously until the

system is disarmed (or timeout occurs). An “Exit Alarm” message is sent to the

central station. Also results if an alarm from an exit or interior zone occurs

within 2 minutes after the end of an Exit Delay.

CHECK

indicates that a problem exists with the displayed zone(s) and requires

attention.

ALARM 1xx

FAULT 1xx

CHECK 1xx

1xx

indicates that communication between control and a zone expander or wireless

receiver is interrupted, where “xx” is the device address. Check the wiring and

DIP switch settings on the units.

If field *199 is set to “1,” all ECP module problems are displayed as “91.”

If there are wireless sensors in the system, the Check condition may also be

caused by some change in the environment that prevents the receiver from

receiving signals from a particular sensor.

SYSTEM LO BAT

LO BAT

BAT

with no zone number indicates that the system's standby battery is weak.

with a zone number and a once-per-minute beeping at the keypad indicates

that a low-battery condition exists in the wireless sensor displayed (zone “00”

indicates a wireless keypad). If the battery is not replaced within 30 days, a

“CHECK” display may occur.

NOTE: Some wireless sensors contain a non-replaceable long-life battery which

requires replacement of the entire unit at the end of battery life (e.g., Nos.

5802, 5802CP).

Telephone Line Failure, indicates that a monitored telephone line (if

programmed in field *92) has been cut or disconnected. Depending on how the

system was programmed, the keypad may also produce a trouble sound, and

the external sounder may be activated. Silence by entering installer code +

OFF.

TELCO FAULT

Busy-Standby

Mode m Comm

If this remains displayed for more than 1 minute, the system is disabled.

The system is in communication with the central station for change of function

or status verification.

no display

Power Failure

If there is no keypad display at all and the LEDs are unlit, operating power

(AC and battery) for the system has stopped and the system is inoperative.

If the message “AC LOSS” (Alpha display keypads) or “NO AC” (Fixed-Word

display keypads) is displayed, the keypad is operating on battery power only.

If the battery standby capacity is used up during a prolonged AC power outage,

the control's power will shut down to minimize deep discharge of the battery.

A communication failure has occurred.

The keypad is not receiving signals from the control; sees an open circuit.

Backup LRR communication failure.

Bell supervision failure.

Comm. Failure

Open Circuit

Long Rng Trbl

Bell Failure

RCVR Jam

RF jam detected.

KEYPAD LOW BAT

Phone Okay

00 BAT

Wireless keypad low battery.

The dialer test has been successful (CID code 601).

Dialer Off

The dialer is disabled.

Walk test mode is active(CID code 607).

The upload or download session was completed.

The upload or download session failed before completion.

Test in Progress

Upload Completed

Upload Failed

6-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

6-8

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Testing the System

About Test Procedures

After the installation is complete, you should perform the following tests:

System Test:

Dialer Test:

Go/No Go Test:

Checks that all zones have been installed properly and the system responds to faults.

Checks that the phone connection to the central station is working properly.

Checks that transmissions can be received from transmitters. Should be performed

before permanently mounting transmitters.

RF Sniffer Mode: Checks that RF transmitter serial numbers have been properly enrolled.

Battery Tests:

Automatic battery tests are performed by the system.

System Test

With the system in the disarmed state, check that all zones are intact (not faulted). Doors and windows

with contacts should be closed, PIRs should be covered (use a cloth to mask them temporarily if necessary).

If a “NOT READY” message is displayed, press [∗] to display the faulted zone(s). Restore faulted zone(s) if

necessary, so that the “READY” message is displayed.

1. Enter Installer Code + 5 [TEST] , then press “0” at the prompt to start Walk Test mode.

1=DIAL, 0=WALK

(no special display on Fixed-Word keypads)

The following will be displayed and a Contact ID report will be sent (code 607):

TEST IN PROGRESS

(“dd” displayed on Fixed-Word Display Keypads)

2. Upon entering the system test mode, the outside sounder should sound for 1 second.

If the backup battery is discharged or missing, the sounder may not turn on and a “LOW BATTERY”

report will be transmitted with a “TEST” report.

The keypad will beep about every 40 seconds as a reminder that the system is in the Test mode.

NOTE: Wireless motion detectors (Passive Infrared units) will send signals out only if they have been

inactive for 3 minutes (conserves battery life).

3. Test all sensors using the procedure described in the User’s Guide “Testing the System” section.

4. After checking sensors, turn off the test mode by entering installer code + OFF.

NOTE: Test mode automatically ends after 4 hours. During the final 5 minutes (after 3 hours 55

minutes of Test mode), the keypad emits a double-beep every 30 seconds to alert that the end of Test

mode is nearing.

Checking Transmitter Enrollment (Sniffer Mode)

Use this mode to verify that all transmitters have been properly programmed. Make sure both partitions

are disarmed before trying to enter this mode, since this is a system-wide command.

1. Press [Installer code] + [#] + 3.

NOTE: If the communicator is in the process of sending a report to the central station, the system will

not go into the Sniffer mode. If so, wait a few minutes, and try again.

The keypads in both partitions will display all zone numbers of wireless units (in both

partitions) programmed into the system. Fault each transmitter in turn, causing each one to

send a signal. As the system receives a signal from each of the transmitters, the zone number of

that transmitter disappears from the display.

2. After all transmitters have been checked, exit the sniffer mode by keying [Installer code] + OFF.

IMPORTANT: Sniffer mode does not automatically expire. You must manually exit Sniffer mode (by

entering [Installer code] + OFF) to return to normal operation.

7-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

NOTES: • All BR type units must physically be activated to clear the display.

• When one button of a transmitter (RF, UR, or BR) is activated, all zones assigned to other

buttons on that transmitter are cleared from the display. This also applies to 5816 and

5817 transmitters, which have multiple loops (zones).

• Any transmitter that is not “enrolled” will not turn off its zone number.

Go/No Go Test Mode

The Go/No Go Test verifies adequate RF signal strength from the proposed transmitter location, and allow

you to reorient or relocate transmitters if necessary, before mounting the transmitters permanently. This

mode is similar to the Transmitter Test mode, except that the wireless receiver gain is reduced. This will

enable you to make sure that the RF signal from each transmitter is received with sufficient signal

amplitude when the system is in the normal operating mode.

1. Enter [Installer code] + [#] + 4 from the partition being tested. For multi-partition systems, repeat this

test for each partition.

2. After you have placed transmitters in their desired locations and the approximate length of wire to be

run to sensors is connected to the transmitter's screw terminals (if used), fault each transmitter. Do not

conduct this test with your hand wrapped around the transmitter, as this will cause inaccurate results.

a. The keypad will beep three times to indicate signal reception and display the zone number.

b. If the keypad does not beep, you should reorient or move the transmitter to another location.

Usually a few inches in either direction is all that is required.

4. If each transmitter produces the proper keypad response when it is faulted, you can then permanently

mount each of the transmitters according to the instructions provided with them.

5. Exit the Go/No Go Test mode by entering: [any user code (partition-specific)] + OFF.

Dialer Communication Test and Periodic Test Reports

1. Enter Installer Code + 5 [TEST], then press “1” at the prompt to start the Dialer Test.

1=DIAL, 0=WALK

(no special display on Fixed-Word keypads)

The following will be displayed (accompanied by 2 beeps) if test is successful:

PHONE OKAY

(“Cd” displayed on Fixed-Word Display Keypads)

A Contact ID report will also be sent (code 601)

If the dialer test is unsuccessful, “COMM FAILURE” (or FC) is displayed.

2. Enter Installer code + OFF to clear the display and exit.

Automatic Periodic Test Report

The system can be set to automatically send test reports (enabled in field *64; Contact ID code 602) at

specified intervals. Frequency of the reports is set in Scheduling mode (event 11) or by the following key

commands: installer code + [#] + 0 + 0 = test report sent every 24 hours

installer code + [#] + 0 + 1 = test report sent once per week

installer code + [#] + 0 + 2 = test report sent every 28 days

Each mode sets schedule 32 (VISTA-20P) or schedule 08 (VISTA-15P) to the selected repeat option; the first

test report is sent 12 hours after command.

To ensure that test reports are sent at the times expected, set the Real-Time Clock to the proper time

before entering the test report schedule command.

Automatic Standby Battery Tests

1. An automatic test is conducted every 3 minutes to ensure that a standby battery is present and

properly connected. If a battery is not present or is not properly connected, a “LOW BATTERY”

message is displayed and, if so programmed, will be reported to the central station.

2. A battery capacity test is automatically conducted for 2 minutes every 4 hours, beginning 4 hours after

exiting the Programming mode or after powering up the system. In addition, entry into the Test mode

will also cause a battery capacity test to be initiated. If the battery cannot sustain a load, a “Low

Battery” message is displayed and, if so programmed, will be reported to the central station.

7-2

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Specifications & Accessories

Security Control

1. Physical: 12-1/2” W x 14-1/2” H x 3” D (318mm x 368mm x 76mm)

2. Electrical:

VOLTAGE INPUT: 16.5VAC from plug-in 25VA transformer, ADEMCO 1321 (in U.S.A.)

RECHARGEABLE BACKUP BATTERY: 12VDC, 4AH (sealed lead acid type). Charging

Voltage: 13.8VDC.

ALARM SOUNDER: 12V, 2.0 Amp output can drive 12V BELLS or can drive one or two

702 (series connected) self-contained 20-watt sirens. Do not connect

two 702s in parallel.

AUXILIARY POWER OUTPUT: 12VDC, 600mA max.

NOTE: For UL installations, Alarm Sounder plus Auxiliary Power currents should

not exceed 600mA total.

FUSE: Battery (3A) No. 90–12

3. Communication:

FORMAT SUPPORTED:

ADEMCO Express:

10 characters/sec, DTMF (TouchTone) Data Tones,

1400/2300Hz ACK, 1400Hz KISSOFF.

ADEMCO Low Speed: 10 pulses/sec, 1900Hz Data Tone, 1400Hz ACK/KISSOFF.

Radionics/SESCOA:

20 pulses/sec, 1800Hz Data Tone, 2300Hz ACK/KISSOFF.

Can report 0-9, B-F

Ademco Contact ID

10 characters/sec., DTMF (TouchTone) Data Tones,

1400/2300Hz ACK, 1400Hz KISSOFF.

LINE SEIZE: Double Pole

RINGER EQUIVALENCE: 0.1B

FCC REGISTRATION No.: 5GBUSA-44003-AL-E

4. Maximum Zone Resistance: Zones 1–8 = 300 ohms excluding EOLR standard zones

Compatible Devices

Keypads:

6150 Fixed-Word Keypad, 6160 Alpha Keypad, 6150V and

6160V Voice Keypads, 6270 Touch Screen Keypad,

Symphony Advanced User Interface

Wireless Receivers:5881L/5882L: accepts up to 8 transmitters

5881M/5882M: accepts up to 16 transmitters

The Receiver in the 6150rf is the

equivalent of a Medium receiver and

will support only 16 wireless zones.

5881H/5882H: accepts up to system maximum transmitters

5800TM Transmitter Module (used with Wireless 2-Way Keypads)

5883 Transceiver: accepts up to system maximum transmitters

6150RF Keypad/Transceiver: accepts up to system max. transmitters

Zone Expansion: 4219 WIRED EXPANSION MODULE

4229 WIRED EXPANSION/RELAY MODULE

4204 RELAY MODULE

Relay Module:

Phone Modules:

4285 PHONE MODULE

4286VIP PHONE MODULE

Long Range Radio 7835C/7845C

8-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

2-Wire Smoke Detector:

Detector Type

System Sensor Model No.

2300TB

2400

Photoelectric w/heat sensor, direct wire

Photoelectric, direct wire

Photoelectric w/heat sensor, direct wire

Photoelectric

Photoelectric w/heat sensor

Ionization, direct wire

2400TH

2451 w/B401B base

2451TH w/B401B base

1400

Ionization

Photoelectric duct detector

Ionization duct detector

Low-profile, Photoelectric, w/135°F thermal

Low-profile, Ionization type, direct wire

1451 w/B401B base

2451 w/DH400 base

1451D w/DH400 base H

2100T

1100

Transformers:

Sounders:

1321: 16.5VAC, 25VA Plug-In Transformer (No. 1321CN in Canada)

1361X10: 16.5VAC, 40VA Powerline Carrier device Interface AC Transformer

Ademco AB-12M 10” Motorized Bell & Box

Ademco 1011BE12M 10” Motorized Bell & Box

Ademco 702 Outdoor Siren

Ademco 719 2-Channel Siren

Ademco 747 Indoor Siren

Ademco 747UL Indoor Siren

Ademco 744 Siren Driver

Ademco 745X3 Voice Siren Driver

Ademco 705-820, 5-inch Round Speaker

Ademco 713 Speaker

System Sensor PA400B (beige)/; PA400R (red) Indoor Piezo Sounder

8-2

Download from Www.Somanuals.com. All Manuals Search And Download.

5800 Series Transmitter Input Loop Identification

All of the transmitters illustrated below have one or more unique factory assigned input (loop) ID codes. Each of the input

loops requires its own programming zone (e.g., a 5804's four inputs require four programming zones).

LOOP 3

LOOP 2

LOOP 3

LOOP 4

YOU MUST

ENROLL

THIS

LOOP 4

YOU MUST

ENROLL

THIS

LOOP 4

LOOP 2

LOOP 1

NOTE: For information on any transmitter not

shown, refer to the instructions accompanying

that transmitter for details regarding loop

numbers, etc.

LOOP 2

LOOP 1

YOU MUST

ENROLL

LOOP

BUTTON

THIS BUTTON

BUTTON

LOOP 3

LOOP 1

SET

HOUSE

CODE

5801

ENROLL AS

"UR" OR "RF"

5802MN

ENROLL AS

"UR" OR "RF"

5804BD

5804

ENROLL AS "BR"

UL NOTE: The following transmitters are

not intended for use in UL

installations:

LOOP 1

(PRIMARY)

LOOP 2

(AUX.

CENTER)

LOOP 2

(REED)

LOOP 2

5808

(REED)

ENROLL AS "RF"

5802MN, 5802MN2, 5804,

5804BD, 5814, 5816TEMP,

5819, 5819WHS & BRS, and

5850.

LOOP 1

(TERMINALS)

LOOP 1

(TERMINALS)

LOOP 3

(AUX.

RIGHT)

ALTERNATE

POSITION

FOR LOOP 2

5816

5817

5809

5816MN

ENROLL AS "RF"

LOOP 2

(REED)

LOOP 2

(REED)

LOOP 3

LOOP

MOTION

(TERMINALS)

LOOP 1

(INTERNAL

SHOCK

LOOP 1

(TERMINALS)

(Green)

(Red)

SENSOR

LOOP 3

(TERMINALS)

(Yellow)

5890

ENROLL AS

"RF" OR "RM"

5819

ENROLL AS "RF"

5819S (WHS & BRS)

ENROLL AS "RF"

5850 (GBD)

ENROLL AS "RF"

V20P-006-V0

Compatible 5800 Series Transmitters Table

Model

Product

Input Type

Description

• Four pushbuttons, each with a unique input (loop) code.

• Programmable responses (e.g., Panic, Arm, Disarm, etc.)

5801

Wireless Panic

Transmitter

UR or RF

• Has single pushbutton.

5802

Pendant (Personal

BR Only

Emergency Transmitter)

• Usually programmed for response type of 24-Hr audible or 24-Hr

Silent (other zone responses are possible).

Same as 5802.

5802CP

5802MN

5804

Belt Clip (Personal

Emergency)

BR Only

UR or RF

BR Only

Same as 5802.

Miniature (Personal

Emergency Trans.)

• Has four pushbuttons, each with a unique input (loop) code.

• Programmable responses (e.g., Arm, Disarm, etc.)

• House ID must be set.

• Requires 5800TM Transmitter Module.

Wireless Key

Transmitter

5804BD

Bi-Directional

Wireless Key

• Can indicate system status via its 2 LEDs and built-in sounder.

• Has four pushbuttons, each with a unique input (loop) code.

• Operates the system similarly to wired keypads.

One-piece smoke detectors with a built-in transmitter.

5806

5807

5808

Wireless

Photoelectric Smoke

Detectors

One-piece rate-of-rise heat detector with a built-in transmitter.

5809

Heat Detector

Has two unique input (loop) codes: one for a wired closed circuit

contact loop; the other for its built-in reed switch (used with a

magnet).

5816

Door/Window

Transmitters

5816MN

Transmits a fault condition when temperature drops below 45°F.

5816TEMP

Low-Temp. Sensor

8-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Compatible 5800 Series Transmitters Table (continued)

Model

Product

Input Type

Description

Has three unique input (loop) codes: one for a “Primary” contact

loop with programmable options; the others for two “auxiliary”

closed circuit contact loops.

5817

Multi-Point Universal

Transmitter

• Reed switch magnetic contact sensor; easily hidden in the frame

5818

5819

Recessed Transmitter

and edge of a door or window.

• Has a single unique input (loop) code.

• Connects to externally mounted inertia-type shock detector (not

supplied).

Shock Processor

Transmitter

• Has built-in tampered cover switch.

• Has 3 unique input (loop) codes:

Loop 1: Terminals for a wired, N.C. sensor loop.

Loop 2: For a closed circuit contact loop using the built-in reed

switch in conjunction with a magnet.

Loop 3: Terminals for a wired, closed circuit contact loop.

5819WHS

5819BRS

Shock Processor

Transmitter

• Has built-in shock sensor.

• Has built-in tampered cover switch.

• Has 3 unique input (loop) codes:

Loop 1: Built-in shock sensor loop wired to TB1 (normally closed).

Loop 2: For a closed circuit contact loop using the built-in reed

switch in conjunction with a magnet.

Loop 3: Externally wired, closed circuit loop connected to TB2.

5827

Wireless Keypad

Uses House

ID only

• Can be used to turn the burglary protection on and off.

• Features the same built-in panic functions as wired keypads.

• The keypad is identified as zone “00” on wired keypads when it

transmits with a low battery.

5827BD

Wireless Two-Way

Keypad

Uses House

ID only

• Requires 5800TM Transmitter Module.

• Operates the system similarly to wired keypads, including panics.

• Can indicate system status via its 3 LEDs and sounder.

• Includes 3 panic keys.

5849

5890

Glassbreak Detector

PR Detector

• House ID must also be set.

• Requires both sound and shock of breaking glass to cause alarm

to be transmitted.

Dual-element passive infrared detector/transmitter with built-in

selectable pulse count.

Note: There is a 3-minute lockout between fault transmissions to

conserve battery life.

5899

Magnets

Package of 4 magnets for use with 5816 and 5817 transmitters.

8-4

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N

Regulatory Agency Statements

RADIO FREQUENCY EMISSIONS

Federal Communications Commission (FCC) Part 15

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

TELEPHONE/MODEM INTERFACE

FCC Part 68

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration

number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested.

This equipment uses the following USOC jack: RJ31X

This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This

equipment is hearing-aid compatible.

Industry Canada

NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications

network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements

document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications

company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with

the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the

user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic

water pipe system, if present, are connected together, This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or

electrician, as appropriate.

Ringer Equivalence Number Notice:

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals

allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the

requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Industrie Canada

AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de

protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences

techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de

télécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier

qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de

télécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par

l’utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes

téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante

dans les régions rurales.

Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des

installations électriques, ou à un électricien, selon le cas.

AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui

peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs,

à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.

9-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

UL NOTICES

✱

1. Entry Delay No. 1 and No. 2 (fields 35, 36) cannot be greater than 30 seconds for UL

Residential Burglar Alarm installations, and entry delay plus dial delay should not

exceed 1 minute. For UL Commercial Burglar Alarm installations, total entry delay may

not exceed 45 seconds.

2. For UL Commercial Burglar Alarm (Grade AA) and UL Residential Burglar Alarm

installations with line security, total exit delay time must not exceed 60 seconds. For UL

Burglar Alarm installations without line security (Grade A), total exit delay time must

not exceed 120 seconds.

✱

3. The maximum number of reports per armed period (field 93) must be set to “0”

(unlimited) for UL installations.

4. Periodic testing (see scheduling mode) must be at least every 24 hours.

5. Alarm Sounder plus Auxiliary Power currents must not exceed 600mA total for UL

installations (Aux power 500mA max.).

6. All partitions must be owned and managed by the same person(s).

7. All partitions must be part of one building at one street address.

8. If used, the audible alarm device(s) must be placed where it/they can be heard by all

partitions.

9. For UL commercial burglar alarm installations the control unit must be protected from

unauthorized access. The tamper switch installed to protect the control unit enclosure

door is suitable for this purpose.

10. Remote downloading without an alarm company technician on-site (unattended

downloading) is not permissible for UL installations.

11. Auto-disarming is not a UL Listed feature.

Notes for SIA Installations

1. As SIA limits for delay of alarm reporting and sounding can exceed UL limits for

commercial and residential applications, the following UL requirements per UL681 are

provided:

The maximum time that a control unit shall be programmed to delay the transmission of

a signal to a remote monitoring location, or to delay the energizing of a local alarm

sounding device to permit the alarm system user to enter and disarm the system, or to

arm the system and exit shall not exceed:

a) 60 seconds for a system with standard line security or encrypted line security,

b) 120 seconds for a system without standard line security or encrypted line security, or

c) 120 seconds for a system that does not transmit an alarm signal to a remote

monitoring location.

2. *34 Exit Delay: minimum exit delay is 45 seconds

3. *35/*36 Entry Delay 1 and 2: minimum entry delay is 30 seconds.

4. *39 Power Up in Previous State: must be “1,” power up in previous state

5. *40 PABX Access Code or Call Waiting Disable: If call waiting is used, call waiting

disable option in field *91 must be set.

6. *50 Burglary Dial Delay: delay must be minimum of 30 seconds.

7. *59 Exit Error Alarm Report Code: Always enabled.

8. *69 Recent Closing Report Code: Always enabled.

9. *91 Option Selection: Exit Delay option should be enabled. If call waiting is used, Call

Waiting Disable must be set to “1” (enabled).

10. *93 No. reports in Armed Period: Must be set for 1 or 2 report pairs.

9-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

9-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Notes

9-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

9-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Notes

9-6

Download from Www.Somanuals.com. All Manuals Search And Download.

S E C T I O N 1 0

Limitations and Warranty

WARNING

THE LIMITATIONS OF THIS ALARM SYSTEM

While this System is an advanced design security system, it does not offer guaranteed protection against

burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to

compromise or failure to warn for a variety of reasons. For example:

• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an

alarm sensor or disconnect an alarm warning device.

• Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will

not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if

the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply

is cut off for any reason, however briefly.

• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm

receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a

metal object is moved into the path.

• A user may not be able to reach a panic or emergency button quickly enough.

• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they

may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according

to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors

used in conjunction with this System may not work are as follows. Smoke detectors may have been

improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot

reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke

detectors also may not sense a fire on another level of a residence or building. A second floor detector, for

example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No

smoke detector can sense every kind of fire every time. In general, detectors may not always warn about

fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas,

improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or

arson. Depending on the nature of the fire and/or location of the smoke detectors, the detector, even if it

operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to

prevent injury or death.

• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in

their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do

create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by

those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed

doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of

any material on the mirrors, windows or any part of the optical system can reduce their detection ability.

Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the

protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection performance

can decrease.

• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are

located on the other side of closed or partly open doors. If warning devices are located on a different level of

the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms.

Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo,

radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however

loud, may not warn hearing-impaired people.

• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be

out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated

intruders.

• Even if the system responds to the emergency as intended, however, occupants may have insufficient time

to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities

may not respond appropriately.

• This equipment, like other electrical devices, is subject to component failure. Even though this equipment

is designed to last as long as 10 years, the electronic components could fail at any time.

(Continued)

10-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

WARNING

THE LIMITATIONS OF THIS ALARM SYSTEM

(Continued)

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate

maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are

working properly. The security keypad (and remote keypad) should be tested as well.

Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating

conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and

the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as

large swings in temperature, may all reduce the actual battery life in a given installation. This wireless

system, however, can identify a true low-battery situation, thus allowing time to arrange a change of battery

to maintain protection for that given point within the system.

Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is

not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in

protecting themselves and continue to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and

their loved ones to learn about these developments.

10-8

Download from Www.Somanuals.com. All Manuals Search And Download.

– INDEX –

1-9

1321 AC Transformer ......1-2, 2-3, 2-11

1361X10.................2-3, 2-11, 2-12, 8-2

24-Hour Audible Alarm ....................3-3

24-Hour Auxiliary Alarm...................3-3

24-Hour Silent Alarm .......................3-3

3+1 and 4+1 Standard Formats.....6-1

42041-2, 2-2, 2-5, 2-6, 2-11, 3-1, 5-8, 5-

9, 6-5, 8-1

Cabinet............................................2-1

CALIFORNIA STATE FIRE

Ideal Model 61–035 .........................2-3

Input Device Type..............5-5, 8-3, 8-4

Installer Code..............3-2, 4-7, 7-1, 7-2

Interior Follower...............3-2, 5-2, 5-11

Interior w/Delay................3-3, 5-2, 5-11

MARSHALL.................................2-2

Caller ID Unit .................................2-13

Character (ASCII) Chart..................16

Character List ................................5-15

Charging Voltage.............................8-1

Chime By Zone................................4-1

Chime Mode ...........................4-10, 6-5

Clean Me Option..............................2-7

common zone..................................5-1

Communication................5-13, 6-1, 8-1

Configurable Zone Type Programming

Fields ..........................................4-9

Confirmation Of Arming Ding ...........4-2

Contact ID Reporting .......................8-1

CSFM..............................................2-2

Custom Message...........................5-15

Custom Words................5-14, 5-15, 16

keypad addresses...................2-5, 4-11

Keypad Programming Fields..........4-11

Keyswitch ....................2-10, 3-4, 5-2, 3

Kissoff.....................................5-11, 6-1

4219 ......1-1, 1-2, 2-2, 2-5, 2-7, 2-8, 8-1

4229 .1-1, 1-2, 2-2, 2-5, 2-6, 2-7, 2-8, 2-

11, 3-1, 5-8, 5-9, 6-5, 8-1

4285 .....................................2-14, 5-15

4285 Phone Module.......................5-14

4286 .....................................2-14, 5-15

4286 Phone Module.......................5-14

5800 Series Transmitters...2-9, 8-3, 8-4

5800TM......................2-9, 8-1, 8-3, 8-4

5801 .........................................2-9, 8-3

5802 ..................................2-9, 6-7, 8-3

5802CP .............................2-9, 6-7, 8-3

5827 ..................................2-9, 4-1, 8-4

5827BD .............................2-9, 4-1, 8-4

5881 .........................................2-2, 2-8

7720PLUS or 7820..........................1-2

9-pin connector..............................2-10

Lock.................................................2-1

Long Range Radio..2-5, 4-1, 4-3, 3, 8-1

Low Battery Message ......................7-2

model 112......................................2-10

Modem ............................................6-7

Module Addresses...........................5-9

momentary switch..........................2-10

Defining Output Functions .............5-10

Descriptor Programming................5-14

device address2-5, 2-11, 3-1, 4-1, 4-11,

5-8, 6-7

Device number ................................5-2

Dialer Communication Test..............7-2

DIP Switches. ..................................2-9

Disarm.............................................3-3

Disarming ...............................5-11, 6-5

Double-Balanced.............................2-6

No Alarm Response................3-4, 5-11

AC Power Supply ............................1-2

AC Transformer...............2-3, 2-12, 8-2

Ademco Contact ID..........................6-3

Alarm Bell Timeout ..........................4-2

Alarm Output ............................2-2, 2-4

Alarm Sounder Timeout ................4-2

Alpha Descriptor..............5-1, 5-4, 5-14

Alpha Vocabulary ..........................5-14

Alpha Vocabulary List....................5-14

ALPHA VOCABULARY LIST........5-16

Arm Away/Stay Report Code...........4-4

Arm–Away.......................................3-3

Arming Away ...................................6-5

Arming Instant .................................6-5

Arming Modes .................................6-6

Arming Stay.....................................6-5

Arm–Stay.........................................3-3

Audio Alarm Verification..........2-13, 4-6

Audio Alarm Verification (AAV)......2-13

AUI..................................................2-5

Authority Levels...............................6-4

Auxiliary Output ...............................2-2

on-board triggers ...........................2-14

Output Device Mapping .....3-1, 5-8, 5-9

Output Devices ................................5-8

Output Functions .............................5-8

Output relays ...................................1-2

Output To Long Range Radio ..........4-1

Enrolling ...................................2-9, 5-1

entering serial number.....................5-5

Entry Delay..........3-3, 4-4, 4-9, 6-6, 6-7

Entry Delay 02................................4-2

Entry/Exit Burglary...........................3-2

Entry/Exit Burglary................................

EOLR .......................................2-6, 8-1

Event Logging..................................4-6

Exit Delay .....4-2, 4-4, 4-6, 4-9, 6-6, 6-7

Exit Error Alarm ..................................3

Exit Error Alarm ...............................6-7

Exit Error Report Code.....................4-4

Expansion Zones...........................2-7

Expert Programming Mode 5-1, 5-4, 5-7

PABX Access Code.........................4-2

Pager #1 Phone No. ................4-7, 4-8

Pager Programming.........................4-7

Pager Programming Fields ..............4-7

Pager Report Options ......................4-8

Paging .............................................4-6

Panic Keys.......................................6-6

Partitions..........................................5-1

Perimeter Burglary...........................3-2

Periodic Test Reports ......................7-2

Phone Line ....................................2-13

Phone Module.1-1, 2-2, 2-5, 2-13, 2-14,

4-1, 4-7, 5-14, 5-15, 16, 8-1

Phone Module Access Code............4-1

Power Failure..........................5-11, 6-7

power supply ...................2-2, 2-4, 10-6

Power Up In Previous State.............4-2

Powerline Carrier Device (X-10) House

ID ................................................4-1

Powerline Carrier Devices1-2, 2-11, 6-5

Primary Phone No............................4-3

Primary Phone No............................4-2

prompt to confirm.............................5-5

PSC04 Powerline Interface............2-11

Factory Defaults...............................3-2

Fast Busy Signal............................2-13

Fault Delay Time ............................4-6

Fire Sounder Timeout......................4-2

Forced Bypass Function ..................4-1

Function Key Programming............5-13

Function Keys.........................4-7, 5-13

Backup Battery................................1-2

Battery Life ......................................2-9

Battery Tests...........................7-1, 7-2

Bell Supervision...............................2-4

Bell Supervision Jumper..................2-4

Bypassing Zones.............................6-5

Go/No Go Test Mode.......................7-2

Handshake ......................................6-1

hardwired zones .......................1-1, 5-3

HAYES Modem ...............................1-1

House ID ....................2-9, 4-1, 8-3, 8-4

Quick Arm Enable..........................4-11

10-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Setup Guide

Relay Modules........................1-2, 2-11

Relay Programming.........................3-1

Report Code..4-4, 4-5, 4-6, 4-9, 5-2, 5-

5, 6-1

tamper switch .........................2-10, 9-2

Telco Line..................................2-13, 3

Telephone Line Monitoring...............1-1

Test Mode ................................7-1, 7-2

Test Restore Report Code...............4-5

Touch Screen Device (AUI) Enable .4-9

touchpads........................................4-4

Transmitter Input Types...................5-3

Trigger outputs ..............................2-12

Trouble by Day/ ...............................3-3

Trouble Displays.......................6-6, 6-7

Wire Run Chart.........................2-4, 2-5

Wireless Key Predefined Default

Templates ..................................5-7

Wireless Key Programming Templates

....................................................5-6

wireless key templates.....................5-6

Word String....................................5-15

Worksheet .......................................2-2

Report Code Formats ......................6-1

Reports In Armed Period...............4-7

response time

....................

, 4-6, 5-2

2-7

RF House ID Code ...................2-8, 4-1

RF Interference................................2-8

RF jam detection ......................1-1, 4-1

RF Jam Option ................................2-8

RF Receiver ...........2-1, 2-2, 2-5, 2-8, 3

RF System.......................................4-1

Ring Detection Count For Downloading

....................................................4-7

RJ31X Jack ...................................2-13

Zone Doubling .................................2-6

Zone Lists...............................3-1, 5-12

Zone Not Used.................................3-2

Zone Programming Procedure.........5-1

Zone Type .......................................5-5

Zone Types......................3-2, 5-2, 5-11

Verify Operation...............................2-7

Vocabulary List..............................5-14

SA4120XM-1 Cable.........................2-3

Schedules........................................5-2

Security Codes .........................1-1, 6-4

Silent Burglary.............3-4, 5-2, 5-11, 3

Silent Panic .....................................6-6

Single Alarm Sounding Per Zone.....4-1

Smoke Detectors.............................8-3

Sniffer Mode.............................5-4, 7-1

sounder connections........................2-4

Supervised Fire ...............................3-3

Supplementary Power .....................2-4

Swinger Suppression....................4-7

System Communication.....4-9, 5-2, 6-1

System Operation.....5-6, 5-7, 5-11, 5-2

System Status Report Codes...........4-4

System Test ...................................7-1

10-10

Download from Www.Somanuals.com. All Manuals Search And Download.

}

A - 2 0 V P I S O T N L

Z O N E 8

H I

L O

Z O N E 7

H I

Z O N E 6

Z O N E 5

L O

H I

Z O N E 4

Z O N E 3

L O

H I

Z O N E 2

L O

O U P S ) T H G R

O M E ( F I T R H E R O R B O

4 O 0 T A D D I T I O F N O A R L U Z P O N E S

O P T I O N A L

L O

H I

Z O N E 1

O R S

C A N B E U S E D F O R 2 - W I R E S M O K E D E T E C T

O A U T A T

A D D K E W Y : P Y E L L O

A D

O M K E I Y N A P T F A R D

G R E E N :

A D P W K R E ( Y P R E D :

B L K

) +

2 )

( T R I G .

O U T P U T 1 8

G N D

X U

1 )

+ 1 2 A

( T R I G .

}

O U T P U T 1 7

O U N D A ( - D ) R G E R T K U E R Y C N P K : B L A

Figure 17. Summary of Connections

10-11

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165 Eileen Way,

Syosset, New York 11791, warrants its product(s) to be in conformance with its own plans and specifications and to be

free from defects in materials and workmanship under normal use and service for 24 months from the date stamp

control on the product(s) or, for product(s) not having a manufacturer’s date stamp, for 12 months from date of original

purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period

shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or

labor, any product(s) which is proved not in compliance with Seller's specifications or proves defective in materials or

workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise

if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service.

Connection of any device(s) to a communicating bus of a Honeywell security system (e.g., keypad bus, polling loop)

other than those manufactured or approved by Honeywell shall void this warranty. For warranty service, return

product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR

PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL

SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR

ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF

THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will

prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product(s) will in all

cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm

system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an alarm, but

it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a

result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY

DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING.

HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR

DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR

ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF

THE PRODUCT(S), WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER.

This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s). No

increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.

165 Eileen Way, Syosset, NY 11791

www.honeywell.com/security

ÊK5305-1V5ÈŠ

K5305-1V5 10/04 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Fish Finder H8220 User Manual
Hario Glass Hot Beverage Maker V60 User Manual
Hasbro Board Games 030901693061Ab User Manual
Heat Glo LifeStyle Electric Heater SL 750TRS IPI D User Manual
Heath Zenith Home Safety Product SH 5316 User Manual
HP Hewlett Packard Car Video System D5063 User Manual
HP Hewlett Packard Network Router SR2122 2 User Manual
HP Hewlett Packard Projector mp3320 User Manual
IBM Computer Monitor G41 G50 User Manual
IBM Speaker System 05L1596 User Manual