AVR 7550HD
AUDIO/VIDEO RECEIVER
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. The A/V receiver’s cabinet may be cleaned by gently wiping with a soft
cotton or microfiber cloth. Do not use water or any liquid cleaners.
7. Do not block any of the ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. When the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly
at plugs, convenience receptacles and the point where they exit from
the apparatus.
11. Only use the attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Wet Location Marking
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Service Instructions
CAUTION – These servicing instructions are for use by qualified service
personnel only. To reduce the risk of electric shock, do not perform any
servicing other than that contained in the operating instructions, unless
you are qualified to do so.
Outdoor Use Marking
WARNING – To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
a variety of factors beyond our control, including the nature of the finish,
cleaning materials used, and normal heat and vibration caused by the
use of the product, or other factors. We recommend that caution be exer-
cised in choosing an installation location for the component and in normal
maintenance practices, as your warranty will not cover this type of damage
to furniture.
IMPORTANT SAFETY INFORMATION
Verify Line Voltage Before Use
Your AVR 7550HD has been designed for use with 120-volt AC current.
Connection to a line voltage other than that for which it is intended can
create a safety and fire hazard and may damage the unit.
If you have any questions about the voltage requirements for your specific
model, or about the line voltage in your area, contact your selling dealer
before plugging the unit into a wall outlet.
Cleaning
When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary,
and only after unplugging the AC power cord, wipe it with a soft cloth
dampened with mild soapy water, then a fresh cloth with clean water. Wipe
it dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners,
thinner, alcohol or any other volatile cleaning agent. Do not use abrasive
cleaners, as they may damage the finish of metal parts. Avoid spraying
insecticide near the unit.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied with your unit.
We do not recommend that extension cords be used with this product. As
with all electrical devices, do not run power cords under rugs or carpets or
place heavy objects on them. Damaged power cords should be replaced
immediately by an authorized service center with a cord meeting factory
specifications.
Moving the Unit
Before moving the unit, be certain to disconnect any interconnection cords
with other components, and make certain that you disconnect the unit from
the AC outlet.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the
plug; never pull the cord. If you do not intend to use the unit for any
considerable length of time, disconnect the plug from the AC outlet.
Important Information for the User
This equipment has been tested and found to comply with the limits for a
Class-B digital device, pursuant to Part 15 of the FCC Rules. The limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio-frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that harmful interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the
cabinet may present a shock hazard, and any modification to the product
will void your warranty. If water or any metal object such as a paper clip,
wire or staple accidentally falls inside the unit, disconnect it from the AC
power source immediately, and consult an authorized service center.
CATV or Antenna Grounding
If an outside antenna or cable system is connected to this product, be
certain that it is grounded so as to provide some protection against voltage
surges and static charges. Section 810 of the National Electrical Code,
ANSI/NFPA No. 70-1984, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes and require-
ments of the grounding electrode.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE TO CATV SYSTEM INSTALLER: This reminder is provided
to call the CATV (cable TV) system installer’s attention to article 820-40 of
the NEC, which provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system
of the building, as close to the point of cable entry as possible.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful inter-
ference, and (2) this device must accept interference received, including
interference that may cause undesired operation.
NOTE: Changes or modifications may cause this unit to fail to comply with
Part 15 of the FCC Rules and may void the user’s authority to operate the
equipment.
Installation Location
• To ensure proper operation and to avoid the potential for safety hazards,
place the unit on a firm and level surface. When placing the unit on a
shelf, be certain that the shelf and any mounting hardware can support
the weight of the product.
UNPACKING
The carton and shipping materials used to protect your new receiver during
shipment were specially designed to cushion it from shock and vibration.
We suggest that you save the carton and packing materials for use in ship-
ping if you move, or should the unit ever need repair.
• Make certain that proper space is provided both above and below the
unit for ventilation. If this product will be installed in a cabinet or other
enclosed area, make certain that there is sufficient air movement within
the cabinet. Under some circumstances, a fan may be required.
To minimize the size of the carton in storage, you may wish to flatten it.
This is done by carefully slitting the tape seams on the bottom and collaps-
ing the carton. Other cardboard inserts may be stored in the same manner.
Packing materials that cannot be collapsed should be saved along with the
carton in a plastic bag.
• Do not place the unit directly on a carpeted surface.
• Avoid installation in extremely hot or cold locations, or in an area that is
exposed to direct sunlight or heating equipment.
• Avoid moist or humid locations.
If you do not wish to save the packaging materials, please note that the
carton and other sections of the shipping protection are recyclable. Please
respect the environment and discard those materials at a local recycling
center.
• Do not obstruct the ventilation slots on the top of the unit, or place
objects directly over them.
• Due to the weight of the AVR 7550HD and the heat generated by the
amplifiers, there is the remote possibility that the rubber padding on the
bottom of the unit’s feet may leave marks on certain wood or veneer
materials. Use caution when placing the unit on soft woods or other
materials that may be damaged by heat or heavy objects. Some surface
finishes may be particularly sensitive to absorbing such marks, due to
It is important that you remove the protective plastic film from the front-
panel lens. Leaving the film in place will affect the performance of your
remote control.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
41
44
45
47
47
48
51
51
Manual Speaker Setup
Audio Effects
Video Adjustments
Multizone Operation
System Settings
Advanced Remote Control Functions
Processor Reset
Memory
2
5
7
9
SAFETY INFORMATION
INTRODUCTION
FRONT-PANEL CONTROLS
REAR-PANEL CONNECTIONS
12 MAIN REMOTE CONTROL
FUNCTIONS
15 ZONE 2 REMOTE CONTROL
FUNCTIONS
17 INTRODUCTION TO HOME THEATER
18 CONNECTIONS
18
18
18
18
18
19
19
19
19
20
20
52 TROUBLESHOOTING GUIDE
53 APPENDIX
67 Trademark Acknowledgments
Speaker Connections
Subwoofer
Connecting Source Devices to the AVR
Audio Connections
Digital Audio
67 TECHNICAL SPECIFICATIONS
Analog Audio
Video Connections
Digital Video
Analog Video
Antennas
RS-232 Serial Port
21 SPEAKER PLACEMENT
22 GETTING STARTED
24 INSTALLATION
29 INITIAL SETUP
29
29
30
Using the On-Screen Menu System
Configure the AVR 7550HD, Using EzSet/EQ™ II Technology
Set Up Sources
33 OPERATION
33
33
33
34
34
34
34
34
34
34
35
36
36
37
37
37
39
Turning On the AVR 7550HD
Volume Control
Dolby Volume
Mute Function
Sleep Timer
Audio Effects
Video Modes
WARNING
To prevent fire or shock hazard, do not
expose this appliance to rain or moisture.
For Canadian model
Headphones
This Class B digital apparatus complies with
Canadian ICES-003. For models having a
power cord with a polarized plug:
Source Selection
Using the Tuner
XM® Radio Operation
USB Playback
Internet Radio
Network Playback
Recording
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, fully insert.
Modèle pour les Canadien
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Sur les modèles dont la fiche est polarisee:
Using
Docking Station
Selecting a Surround Mode
40 ADVANCED FUNCTIONS
ATTENTION: Pour éviter les chocs électriques,
introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et
pousser jusqu’au fond.
40
40
40
40
41
Audio Processing and Surround Sound
Analog Audio Signals
Digital Audio Signals
Surround Modes
Dolby® Surround Settings
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Please register your AVR 7550HD at
Harman Kardon AVR 7550HD 7.2-Channel
Audio/Video Receiver
NOTE: You’ll need the product’s serial number. At the same
time, you can choose to be notified about new products and/or
special promotions.
Audio Section
• 105 Watts x 7, seven channels driven at full power at 8 ohms,
20Hz – 20kHz, <0.07% THD, 735 watts total
Thank you for choosing a Harman Kardon®
product!
• High-current capability, ultrawide-bandwidth amplifier design with
low negative feedback
For more than fifty years, the Harman Kardon® mission has been to
share a passion for music and entertainment, using leading-edge
technology to achieve premium performance. Harman Kardon, Inc.,
invented the receiver, a single component designed to simplify
home entertainment without compromising performance. Over
the years, Harman Kardon products have become easier to use,
while offering more features and sounding better than ever. The
AVR 7550HD multizone 7.2-channel digital audio/video receiver
continues this tradition with some of the most advanced audio and
video processing capabilities yet, and a wealth of listening and
viewing options.
• All-discrete amplifier circuitry
• Quadruple-crossover bass management with DVD-Audio bass
management capability
• Dual 32-bit TI DA 710 DSP processors
• 192kHz/24-bit A/D and D/A conversion
• Sampling upconversion to 96kHz
• Dolby® Volume processing
Surround Modes
• Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD
• Dolby Pro Logic® II and IIx (Movie, Music and Game), up to 96kHz
• Dolby Virtual Speaker Version 2 (Reference or Wide, 2-channel)
• Dolby Headphone Version 2, up to 96kHz
• DTS-HD High Resolution Audio™, DTS-HD Master Audio™
• DTS® (5.1; DTS Stereo; DTS-ES® 6.1 Discrete and Matrix)
• DTS 96/24™ (DTS Stereo)
To obtain the maximum enjoyment from your new receiver, please
read this manual and refer back to it as you become more familiar
with its features and their operation.
If you have any questions about this product, its installation or its
operation, please contact your Harman Kardon retailer or custom
• DTS Neo:6® (Cinema 5-, 6- or 7-channel; Music 5-, 6- or
7-channel), up to 96kHz
• Logic 7® (Movie, Music and Game), up to 96kHz
• 5- or 7-Channel Stereo, up to 96kHz
• Surround Off (DSP or Analog Bypass)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Audio Inputs
• AM/FM/XM®* tuner
Ease of Use
• EzSet/EQ™ II automated setup (microphone supplied)
• Analog Audio 1 through 5
• Front-panel Analog Audio
• 6-/8-Channel Analog Audio
• Full-color user interface and setup menu, generated in
high-definition video
• Text-based on-screen menus available to Zone 2
• Two-line dot-matrix front-panel display
• Color-coded connections
Audio/Video Inputs
• Three Analog Video
• Programmable, learning seven-device main remote control
(includes AVR control over The Bridge II)
• Front-panel Analog Video
• Three Component Video 100MHz
• Four HDMI™ (V.1.3a with Deep Color)
• Faroudja DCDi Cinema™ video processing
• Source input renaming
• Lip Sync Delay (up to 180msec)
• RS-232 serial port for system control
• System upgradeable from USB device
• Switched accessory power outlet
• Remote infrared (IR) input and output
• Zone 2 IR input and Carrier IR output
N
Transcodes composite and S-video to component video
N
Transcodes 480i video to component video format, with
upscaling to 1080i
N
Transcodes 480i video to HDMI output, with upscaling
to 1080p
• Two trigger outputs (3–30V DC) for auto turn-on of other
system components
•
dock for iPod** connectivity with audio/video playback
• Ethernet port for Internet Radio and Network
• IEC detachable AC power cord for easy installation
• USB Port for audio and still-image playback from compatible
storage devices
Supplied Accessories
The following accessory items are supplied with the AVR 7550HD.
If any of these items are missing, please contact Harman Kardon
Digital Audio Inputs
• Coaxial: three rear-panel/one front-panel
• Optical: three rear-panel/one front-panel
• System and Zone 2 remote controls
• EzSet/EQ II microphone
Outputs
• 7.2-Channel preamp outputs
• Extension rod for EzSet/EQ II
microphone
• Analog Audio 3 and 4
•
docking station for iPod
• Analog Video 2 (composite and S-video)
• Video Monitor (composite, S-video and component)
• Digital Audio (one coaxial, one optical)
• HDMI (V.1.3a with Deep Color)
• AM loop antenna
• FM wire antenna
• Six AAA batteries
• AC power cord
XM antenna module and subscription to XM service required. Hardware and
*
• Multizone Audio: speaker- and two line-level (one dedicated,
one shared with surround back channels)
service sold separately. XM service is not available in Alaska or Hawaii.
Compatible with most docking iPod models, 4G and later. Video and still-image
viewing requires an iPod that supports video browsing.
**
• Multizone Video: composite
• A-BUS® port
• Headphone
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT- PANEL CONTROLS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT- PANEL CONTROLS
Power Indicator: This LED has three possible modes:
Menu Button: Press to display the menus for the tuner, the
USB device, The Bridge II, the Network or Internet Radio, when any
of those sources is in use.
• Main Power Off: When the AVR is unplugged or the Main
Power Switch is off, this LED is off.
Back/Exit: Press this button to return to the previous menu,
• Standby: Amber indicates that the AVR is ready to be turned on.
• On: When the AVR is turned on, this LED turns white.
or to exit the menu system.
1/57/3Navigation: These buttons are used to navigate the
AVR’s menus, including the menus for the tuner, the USB device,
The Bridge II, the Network and Internet Radio.
NOTE: If the PROTECT message ever appears, turn off the
AVR and unplug it. Check all speaker wires for a possible short.
If none is found, bring the unit to an authorized Harman Kardon
service center for inspection and repair before using it again.
OK: Press this button to select the currently highlighted item.
Headphone Jack: Plug a 1/4" stereo headphone plug into
this jack for private listening.
Standby/On Switch: This electrical switch turns the
receiver on, or places it in Standby mode for quick turn-on.
USB Port: Connect a USB flash drive, to play audio files in
the MP3 or WMA format or still images in the JPEG format. DO NOT
connect a PC, keyboards, pointing devices or other peripheral prod-
ucts to the AVR 7550HD. Do not connect an iPod here; use The
Bridge II instead. Do not connect a USB hub or multi-card device.
Front-Panel Door (not shown): Most of the controls
and connectors described below are hidden behind this door. To
open it, gently grab the right or left edge of the door and pull it
forward and down.
Main Power Switch: This mechanical switch turns the
power supply on or off. It is usually left on, and cannot be turned
on or off using the remote control.
Digital Audio, Video and Analog Audio Front
Inputs: Connect a source component that will only be used
temporarily, such as a digital camera or game console, to these
jacks. Use only one type of audio and one type of video connection.
AVR Settings Button: Press this button to access the
AVR’s main menu.
NOTE: The AVR’s menus refer to these jacks as the Optical
Front, Coaxial Front, Composite Front, S-Video Front and
Analog Front inputs.
Info Settings Button: Press this button to directly access
the AVR’s Source Info submenu, which contains the settings for the
current source.
EzSet/EQ II Microphone Input: This jack is used to
connect the supplied microphone for the EzSet/EQ II procedure
described in the Initial Setup section.
Resolution: Press this button to access the AVR’s video output
resolution setting: 480i, 480p, 720p, 1080i or 1080p.
Volume Knob: Turn this knob to raise or lower the volume.
IMPORTANT NOTE: If the AVR’s video output resolution
is set higher than the capabilities of the actual connection,
you will not see a picture. If the best available video connection
from the AVR to the TV is either composite or S-video, press
this button and change the resolution to 480i.
Message Display: Various messages appear in this two-line
display in response to commands and changes in the incoming signal.
In normal operation, the current source name appears on the upper
line, while the surround mode is displayed on the lower line. When
the on-screen display menu system (OSD) is in use, the current
menu settings appear.
Audio Effects: Press this button to directly access the Audio
Effects submenu, which allows adjustment of the tone and other
audio controls. See the Initial Setup section for more information.
Remote IR Sensor: This sensor receives infrared (IR)
commands from the remote control. It is important to ensure that it
is not blocked. If covering the sensor is unavoidable, use an optional
Harman Kardon HE 1000, or other infrared receiver, connecting it to
the Remote IR Input on the AVR 7550HD’s rear panel.
Video Modes: Press this button for direct access to the Video
Modes submenu, which contains settings that may be used to
improve the picture, if necessary, after you have adjusted the
picture settings using the video display or TV.
Surround Modes: Press this button to select a surround
sound (e.g., multichannel) mode. The Surround Modes menu will
appear on screen, and the menu line will appear in the front-panel
display. See the Advanced Functions section for more information
on surround modes.
Source List: Press this button to select a source device,
which is a component where a playback signal originates, e.g., DVD.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR- PANEL CONNECTIONS
O
I D V - E S
E T O S I C O M P
9
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR- PANEL CONNECTIONS
IR receiver to the Remote IR Input jack. The Remote IR Output may
be connected to the Remote IR Input of a compatible product to
enable remote control through the AVR.
6-/8-Channel Inputs: Connect the multichannel analog
audio outputs of a non-HDMI player (DVD-Audio, SACD™, Blu-ray
Disc™ or HD-DVD, or any other external decoder) to these jacks.
Remote IR Carrier Output: This output is similar in
function to the Remote IR Output, with the difference that this jack
outputs the full infrared signal as received by the AVR’s IR sensor
or the Remote IR Input, while the Remote IR Output jack outputs a
“stripped” signal that has no carrier frequency.
Coaxial 1/2/3 and Optical 1/2/3 Digital Audio
Inputs: If a source has a compatible digital audio output, and
if you are not using an HDMI connection for audio for the device,
connect it to one of these jacks to hear digital audio formats, such
as Dolby Digital, DTS and linear PCM. Use only one type of digital
audio connection for each source.
HDMI Inputs and Output: HDMI (High-Definition
Multimedia Interface) is a connection for transmitting digital audio
and video signals between devices. Connect up to four HDMI-
equipped source devices to the HDMI inputs using a single-cable
connection.
Coaxial and Optical Digital Audio Outputs: If
a source is also an audio recorder, connect one of the Digital Audio
Outputs to the recorder’s matching input for improved recording
quality. Only PCM digital audio signals are available for recording.
Both coaxial and optical digital audio signals are available at either
Digital Audio Output.
When you connect the HDMI Output to your video display, the
AVR 7550HD will automatically transcode analog video signals to
the HDMI format, upscaling to as high as 1080p.
XM Antenna Jack: Plug in an XM Connect-and-Play or
Mini-Tuner antenna module here.
NOTES: When connecting a DVI-equipped display to one of
the HDMI Outputs:
Network Jack: Plug in an RJ-45-compatible cable that con-
nects to a personal computer (PC), router or Internet access. When
connected to a PC, the AVR 7550HD is capable of playing audio and
JPEG files stored on the PC. When connected to the Internet, the
AVR 7550HD may be used to enjoy Internet Radio. See pages 36
and 37 for more information.
• Use an HDMI-to-DVI adapter.
• Make sure the display is HDCP-compliant. If it isn’t, do not
connect it to an HDMI Output; use an analog video connection
instead.
• Always make a separate audio connection.
RS-232 Serial Port: This bi-directional port may be used
to control the AVR 7550HD using an RS-232 serial control link to a
compatible computer or programmable remote control system. Due
to the complexity of programming RS-232 commands, connections
and programming for control purposes should be performed by a
qualified custom installer.
Analog 1 – 5 Inputs: Connect the left and right analog
audio outputs of a source device to any of these inputs. These
inputs may be paired with any video inputs.
NOTES:
• The Analog 3 and 4 inputs are each associated with a set
of outputs. Consider using these connectors for an audio or
video recorder.
Trigger 1 and 2 Outputs: Connect these control jacks
to the trigger input jack of an external component, such as an audio
power amplifier, that you want to power on any time the AVR 7550HD
is turned on, without using the AVR’s Switched Accessory Outlet for
power. When this connection is used, the AVR 7550HD will automat-
ically send a low-voltage signal to the connected device that trig-
gers it to turn on when the AVR 7550HD is on, and off when the
AVR 7550HD is placed in the Standby Mode. The connected compo-
nent must respond to 6-volt presence as the control signal.
• You may optionally connect a source to both an analog and
digital audio input. This is useful for making recordings, for
multizone applications or simply as a backup.
Analog 3 and 4 Outputs: Connect either of these analog
audio outputs to the analog audio inputs of a recording device.
A signal is available at these outputs whenever an analog audio
source is playing.
The Trigger 2 Output may be programmed to transmit its signal only
when certain of the AVR’s source inputs are selected. For example,
to lower a screen when watching a DVD movie, but not while listen-
ing to the tuner, connect the Trigger 2 Output to the screen and pro-
gram it to be on when the DVD source is selected, but off when the
AM, FM or XM bands are in use. See the Initial Setup section for
more information on programming this setting in the Info Settings
menus for each source.
Zone 2 Audio Outputs: Connect these jacks to an external
amplifier to power the speakers in the remote zone of a multizone
system.
Subwoofer 1 and 2 Outputs: If you have a powered
subwoofer with a line-level input, connect it to the Subwoofer 1
Output. For improved performance, connect a second powered
subwoofer to the Subwoofer 2 Output.
Zone 2 Infrared (IR) Input: Connect a remote IR receiver
located in the remote zone of a multizone system to this jack to
control the AVR (and any source devices connected to the Remote
IR Output) from the remote zone.
The Bridge II Input: Connect the included Harman Kardon
docking station to this input for use with most docking
iPod models, 4G and later (not included). Turn the receiver off
(Standby mode) when connecting The Bridge II.
Remote Infrared (IR) Input and Output: When the
remote IR receiver on the front panel is blocked, connect an optional
10
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR- PANEL CONNECTIONS
Fan Vents: This area contains vents used by the AVR 7550HD’s Preamp Outputs: Connect these jacks to an external
fan to cool the system. Maintain a clearance of at least 3 inches
from the nearest surface to avoid overheating the unit. It is normal
for the fan to remain off at most normal volume levels. An automatic
temperature sensor turns the fan on only when it is needed.
amplifier if more power is desired. The Surround Back/Zone 2
Preamp Outputs may be used with an external amplifier to power
the remote zone of a multizone system.
A-BUS Port: Use a Category 5/5e cable to connect this port to
optional A-BUS equipment for multizone operation. When the A-BUS
system is used, it is possible to have a full 7.2-channel system in
the main listening room at the same time the multizone system is
in use.
IMPORTANT NOTE: Never block the fan vents, as doing
so could allow the AVR to overheat to dangerous levels.
Zone 2 Video Output: Connect this composite video jack
to a video display located in the remote zone of a multizone system.
When the multizone system is in use, viewers in the remote zone
will be able to see the AVR’s on-screen text menus and any available
source video, as long as the source is connected to a Composite
Video Input, and that input is specified for that source in the Zone 2
Video setting of the Info Settings menu.
Front, Center and Surround Speaker Outputs:
Use two-conductor speaker wire to connect each set of terminals
to the correct speaker. Remember to observe the correct polarity
(positive and negative connections).
Surround Back/Zone 2 Speaker Outputs: These
speaker outputs are used for the surround back channels in a
7.2-channel home theater, or may be reassigned to a remote room
for multizone operation.
Composite and S-Video 1, 2 and 3 Video Inputs:
Use these jacks to connect your video-capable source components
(e.g., VCR, DVD player, cable TV box) to the receiver. Use only one
type of video connection for each source.
Switched AC Accessory Outlet: You may plug the
AC power cord of one source device into this outlet, and it will turn
on whenever you turn on the receiver. Do not use a source that
consumes more than 50 watts of power.
Composite and S-Video 2 Outputs: Connect one of
these analog video outputs to the composite or S-video inputs of
a recording device. A signal is available at these outputs whenever
an analog video source is playing.
AC Power Input: After you have made all other connections,
plug the AC power cord into this receptacle and into an unswitched
wall outlet.
Composite and S-Video Monitor Outputs: If any
of your sources use composite or S-video connections, connect one
or both of these monitor outputs to the corresponding inputs on
your video display. If your video display is equipped with HDMI or
component video inputs, these connections are unnecessary, as the
AVR 7550HD will convert the composite or S-video source signal
to the correct format for a single video-cable connection to the TV.
Component Video 1, 2 and 3 Inputs: If a video
source has analog component video (Y/Pb/Pr) capability, and if you
are not using an HDMI connection, connect the component video
outputs of the source to one of the sets of component video inputs.
Do not make any other video connections to that source.
Component Video Monitor Outputs: If you are
using one of the Component Video Inputs and your television or
video display is component-video-capable (but does not have
HDMI), connect these jacks to the video display.
NOTES:
• Due to copy-protection restrictions, there is no output at
the Component Video Monitor Outputs for copy-protected
sources.
• Composite and S-video signals are upscaled to as high as
1080i and available at these outputs. If your video display’s
best connection is component video, it is the only video
connection required from the AVR to the display.
AM and FM Antenna Terminals: Connect the included
AM and FM antennas to their respective terminals for radio reception.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN REMOTE CONTROL FUNCTIONS
IR Transmitter Lens
AVR Power Off
AVR Power On
Device Power On
Device Power Off
LCD Display
Source Selectors
Video Modes
Audio Effects
Surround Modes
Alphanumeric Keys
Activity
Menu
Last
Back/Exit
Navigation
OK
Disc Menu
Light
Soft Keys
Volume
Mute
Channel
Transport Controls
Record
Info Settings
Source Settings
Sleep Settings
AVR Settings/Remote Menu
Zone Selector
NOTE: To make it easier to follow the instructions
throughout the manual that refer to this illustration,
a copy of this page may be downloaded from the
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN REMOTE CONTROL FUNCTIONS
The AVR 7550HD remote is capable of controlling up to 14 devices,
including the AVR itself, an iPod docked in the included The Bridge II,
a USB device and a Network device (see page 37 for details). During
the installation process, you may program the codes for your source
components into the remote. To operate a component, press its
Selector button to change the device mode. The device mode will
appear on the top line of the remote’s LCD Display.
LCD Display: This two-line text display informs you of the
current device mode (i.e., which source is active) on the upper line.
When you press a key, the command will appear briefly on the
lower line.
Source Selectors: Press one of these buttons to select a
source device, e.g., DVD, CD, cable TV, satellite or HDTV tuner. This
will also turn on the receiver and switch the remote’s device mode
to operate the source. The first press of the Radio Selector switches
the AVR to the last-used tuner band (AM, FM or XM). Each succes-
sive press changes the band. Similarly, the Network Button toggles
between the Network and Internet Radio sources.
NOTE: Four of the sources do not have dedicated Source
Selectors: Source A, Source B, Source C and Source D. To
select one of these sources, first press the AVR Settings Button,
then press the appropriate Soft Key: Red for Source A, Green
for Source B, Yellow for Source C and Blue for Source D. These
sources may also be selected using the AVR Settings menu.
Audio Effects: Press to directly access the Audio Effects
submenu, which allows adjustment of the AVR’s tone and other
audio controls. See the Initial Setup section for more information.
Each Source Selector has been preprogrammed to control certain
types of components, with only the codes specific to each brand and
model changing, depending on which product code is programmed.
The AUX and Cable/SAT Source Selectors may be used for multiple
device types. All of the external Source Selectors may be reassigned
to other device types (see Initial Setup section).
Video Modes: Press for direct access to the Video Modes
submenu, which contains picture settings to be used after you
have adjusted the picture settings on the video display or TV.
See the Advanced Functions section for more information.
Surround Modes: Press to directly access the Surround
Modes submenu. Scroll to the lines for the Surround Mode categories:
Auto Select, Virtual Surround, Stereo, Movie, Music or Video Game.
The surround mode will change when the menu line is highlighted.
AUX Source Selector: CD player, VCR, HDTV set-top box,
PVD or TiVo® set-top box.
Cable/SAT Source Selector: Cable set-top box or satel-
lite set-top box.
To change the surround mode for the selected category, press the
OK Button when the menu line for the Surround Mode category
matching the audio program is highlighted, and select one of the
available surround mode options using the 1/5Buttons. Press the
OK Button.
IMPORTANT NOTE: All of the AVR 7550HD’s audio and
video inputs are independently assignable. Select the inputs
to which the device is physically connected during Initial
Setup. Any device may be connected to any compatible input
and given any name (e.g., DVD or Game).
See the Advanced Functions section for more information on
surround modes.
Most of the buttons on the remote have dedicated functions,
although the precise codes transmitted vary, depending on the
device mode. Due to the wide variety of functions for various source
devices, only a few of the most-often used functions on the remote
have been included: alphanumeric keys, transport controls, television-
channel control, menu access, and power on and off.
Alphanumeric Keys: Use these buttons to enter numbers
for radio station frequencies or channels, or to select station presets.
Last Channel: When controlling the tuner; a cable, satellite
or HDTV set-top box; or a TV, press this button to return to the
previous station or channel. For Internet Radio, this is only available
to toggle between stations previously saved as presets.
Buttons dedicated to the AVR are available at any time, even in
another device mode: AVR Power On and Off, Audio Effects, Video
Modes, Surround Modes, Volume, Mute and Sleep Settings. Press
the AVR Settings Button near the bottom of the remote to return it
to AVR mode.
Activity: With this button, up to 11 Activities may be pro-
grammed to transmit a series of commands with a single press.
Execute an Activity by pressing this button, then the Alphanumeric
Key (or the AVR Power On or Off Button by themselves) into which
it was programmed. See the Advanced Functions section for more
information on Activities.
A button’s function depends on which component is being con-
trolled. See Table A14 in the appendix for listings of the functions
for each type of component.
Back/Exit: Press to return to the previous menu or to exit the
menu system.
IR Transmitter Lens: As buttons are pressed on the
remote, infrared codes are emitted through this lens.
Menu Button: This button is used within the Now Playing
menu for the tuner (including XM Radio), USB, The Bridge II, Internet
Radio and the Network, and to display the main menu on some
source devices. To display the AVR 7550HD’s main menu, press the
AVR Settings Button.
AVR Power On Button: Press to turn on the AVR. The
Master Power Switch behind the front-panel door must be on.
AVR Power Off Button: Press to turn off the AVR 7550HD.
Device Power On Button: Press a device’s Source
Selector, then press this button to turn on the device.
(
)
Navigation 1/57/3 and OK Buttons: These buttons
are used to make selections within the menu system and to operate
the tuner.
Device Power Off Button: Press a device’s Source
Selector, then press this button to turn off the device.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN REMOTE CONTROL FUNCTIONS
Light: Press to illuminate the buttons on the remote. Press it
again to turn the back light off, or wait 10 seconds after the last
button press for the light to turn off on its own.
Disc Menu: While a DVD is playing, press the DVD Source
Selector, then this button, to display the disc’s menu.
Soft Keys: These buttons are used to select sources A, B, C
and D (see note on page 13), or for other functions with some
source devices. See Table A14 in the appendix for details. They
are also used with a Teletext-capable television if your broadcast,
cable or satellite provider offers Teletext service.
Volume Control: Press to raise or lower the volume.
Mute Button: Press to mute the AVR 7550HD’s speaker and
headphone outputs. To end the muting, press this button, adjust the
volume, or turn off the receiver.
Channel/Page Control: When the tuner has been selected,
this control changes the station. When using The Bridge II or a USB
drive, this control allows you to scroll a page at a time through a
long list of content. While operating a cable, satellite or HDTV set-
top box or a television, press these buttons to change channels.
Transport Controls: These buttons are used to control
source playback.
Record Button: Use this button to make recordings when
an audio or video recorder is in use.
AVR Settings/Remote Menu Button: Press to
display the AVR’s Main Menu, or to switch the remote to AVR device
mode. Press and hold for 3 seconds to access the menu for the
remote control. The menu commands and options will appear in
the LCD Display.
The functions are: program the codes for a device, learn codes
for an individual key, change the device type of a selector, program
an activity (macro), program punch-through functions for channel
control or transport control, rename a device or a key’s function,
change the brightness of the back light, reset the remote to its
factory-default status, or exit the remote menu. See the Initial
Setup section for details on programming the remote, and see
the Advanced Functions section for further information.
Info Settings Button: Press to display the AVR’s Info Menu,
which contains the settings for the current source.
Source Settings Button: Press a Source Selector and
then this button to display a source device’s settings menu.
Sleep Settings Button: Press to activate the sleep timer,
which turns off the receiver after a programmed period of time of
up to 90 minutes. Each press decreases the timer by 10 minutes,
ending with the “Sleep Off” message.
Zone Selector: Use this switch to select whether AVR commands
will affect the main listening area (Zone 1) or the remote zone of a
multizone system (Zone 2). For normal operation, leave the switch
in the Zone 1 position.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ZONE 2 REMOTE CONTROL FUNCTIONS
IR Transmitter
Power Off
Mute
USB
Source Selectors
Network
Sleep Settings
AVR Settings
BACK/EXIT
MENU
Back/Exit
Volume Controls
Zone Selector
Menu
Navigation
OK
Transport Controls
Zone Indicator
NOTE: To make it easier to follow the instructions
throughout the manual that refer to this illustration,
a copy of this page may be downloaded from the
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ZONE 2 REMOTE CONTROL FUNCTIONS
The Zone 2 remote control is used in the remote zone of a multizone
system with an IR receiver connected to the Zone 2 IR Input or an
A-BUS device. It may be used to control the power, volume and
mute functions or to select a source input for the remote zone, and
to control a Harman Kardon source connected to one of the AVR’s
Remote IR Outputs or the A-BUS IR Output.
Menu Button: This button is used within the Now Playing
menu for the tuner (including XM Radio), USB, The Bridge II, Internet
Radio and the Network, and to display the main menu on some
source devices. To display the AVR 7550HD’s main menu, press the
AVR Settings Button.
(
)
Navigation 1/57/3 and OK Buttons: These buttons
are used to make selections within the menu system and also to
operate the tuner, USB, The Bridge II, Internet Radio and the
Network device.
The Zone 2 remote may also be used in the main listening room
to directly control the AVR 7550HD and Harman Kardon DVD, CD or
tape players. When the Zone Selector is pressed to switch the remote
to Zone 1 mode (the Zone Indicator will turn green), the power,
volume and mute controls will only affect the main listening area.
To control operation for the remote zone, press the Zone Selector
so that the Zone Indicator turns red.
Zone Selector and Zone Indicator: Each press
of the Zone Selector determines whether the AVR commands will
affect the main listening area (Zone 1) or the remote zone (Zone 2).
The Zone Indicator will turn green when Zone 1 has been selected,
and red for Zone 2. The Zone Indicator will also light briefly when-
ever any button is pressed.
The Zone 2 remote requires two AAA batteries (included) that are
installed in the battery compartment on the back of the remote. Make
sure to observe proper polarity by matching the + and – symbols
on the batteries to the symbols printed inside the compartment.
Volume Controls: Press to raise or lower the volume level
in the remote zone.
IR Transmitter: This lens emits infrared codes when buttons
on the remote are pressed.
Power: Press to turn the AVR 7550HD on or off. The AVR also
turns on its multizone system automatically when any of the Input
Selectors is pressed, even if the AVR itself is in Standby mode.
When in the main listening room, press any Input Selector or the
AVR Selector to turn on the AVR 7550HD.
Mute: Press to mute the AVR 7550HD’s remote zone speakers
temporarily. To end the muting, press this button, adjust the volume,
or turn off the multizone system. Make sure to switch the remote
to Zone 2 mode, so that only the remote zone will be affected.
Source Selectors: Press one of these buttons to select a
source device for the remote zone. It will also turn on the multizone
system and switch the remote to the source’s device mode. You
may select a different external source device than that for the main
room, but not different internal sources (the tuner, USB, Internet
Radio or the Network). If you select the same source as that for
the main room, then any commands sent to the source will affect
both zones. The first press of the Radio Selector switches the AVR
to the last-used tuner band (AM, FM or XM). Each successive press
changes the band. Each press of the Network Button toggles
between the Network and Internet Radio sources.
Transport Controls: These buttons are used to control
many source components.
AVR Settings Button: Press to display the AVR’s Main
Menu. It is also used to switch the remote to AVR device mode.
Sleep Settings Button: Press to activate the sleep timer,
which turns off the receiver after a programmed period of time of
up to 90 minutes. Each additional press decreases the timer by
10 minutes, ending with the “Sleep Off” message.
Back/Exit: Press to return to the previous menu or to exit the
menu system.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION TO HOME THEATER
This introductory section will help you to familiarize yourself with
some basic concepts unique to multichannel surround sound
receivers, which will make setup and operation smoother.
power of an explosion, adding realism and excitement to your
home theater. Some people use two subwoofers, for additional
power and even distribution of the sound.
Typical Home Theater System
Surround Modes
A home theater typically includes an audio/video receiver, which
controls the system; a disc player; a source component for television
There are different theories as to the best way to present surround
sound and to distribute information to the speakers. A variety of
broadcasts (cable box, satellite dish receiver, HDTV tuner or antenna algorithms have been developed in an effort to reproduce the way we
connected to the TV); a video display (television); and loudspeakers.
hear sounds in the real world, resulting in a rich variety of options.
Several companies have taken surround sound in different directions:
Multichannel Audio
• Dolby Laboratories – Dolby TrueHD, Dolby Digital Plus,
Dolby Digital, Dolby Digital EX, Dolby Pro Logic II and IIx, Dolby
Virtual Speaker, Dolby Headphone
The main benefit of a home theater system is the placement of
loudspeakers around the room to produce “surround sound.”
Surround sound immerses you in the presentation for increased
realism.
• DTS – DTS-HD High Resolution Audio, DTS-HD Master Audio,
The AVR 7550HD may have up to seven speakers connected directly
to it (plus up to two subwoofers). Each main speaker is powered by
its own amplifier channel inside the receiver. A system with more
than two speakers is called a multichannel system.
DTS, DTS-ES (Discrete and Matrix), DTS Neo:6, DTS 96/24
• Harman International (the Harman Kardon
parent company) – Logic 7
• Stereo Modes – Generic modes that expand upon conven-
tional 2-channel stereo, including 5- and 7-channel stereo
• Front Left and Right – The main speakers are used as
in a 2-channel system. In many surround modes, these speakers
are secondary, while the main action, especially dialogue, is
moved to the center speaker.
Table A13 in the appendix contains detailed explanations of the
mode groups and the mode options available within each group.
Digital modes, such as Dolby Digital and DTS, are only available
with specially encoded programs, such as HDTV, Blu-ray Disc media
and digital cable or satellite television. Other modes may be used
with digital and analog signals to create a different surround presen-
tation, or to use a different number of speakers. Surround Mode
selection depends upon the number of speakers in your system, the
materials you are watching or listening to, and your personal tastes.
• Center – The center speaker is used for dialogue in movies
and television programs, allowing the dialogue to originate near
the actors’ faces, for a more natural sound.
• Surround Left and Right – The surround speakers
improve directionality of ambient sounds. In addition, more loud-
speakers play dynamic soundtracks without risk of overloading
any one speaker.
• Surround Back Left and Right – Additional surround
speakers may be placed behind the listening position, improving the
precision of ambient sounds and allowing for more realistic pans.
The surround back speakers are used with surround modes
designed for 7.1-channel systems, such as Dolby Digital EX,
Dolby Digital Plus, Dolby TrueHD, DTS-ES (Discrete and Matrix),
DTS-HD High Resolution Audio, DTS-HD Master Audio and Logic 7
(7.1 and 7.2 modes). The surround back speakers are optional,
and the AVR 7550HD may be set up with a 5.1- or 5.2-channel
system in the main listening area, and the surround back channels
reassigned to a multizone system, where the surround back
channels power loudspeakers located in another room.
Many people expect the surround speakers to play as loudly as
the front speakers. Although all of the speakers in the system will
be calibrated to sound equally loud at the listening position, most
artists use the surround speakers for ambient effects only, and
they program their materials to steer very little sound to these
speakers.
• Subwoofer – A subwoofer is designed to play only the lowest
frequencies (the bass). It augments smaller, limited-range satellite
speakers used for the other channels. Many digital-format programs,
such as movies recorded in Dolby Digital, contain a low-frequency
effects (LFE) channel which is directed to the subwoofer. The LFE
channel packs the punch of a rumbling train or airplane, or the
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
There are different types of audio and video connections used
to connect the receiver, the speakers, the video display, and the
source devices. The Consumer Electronics Association has estab-
lished the CEA® color-coding standard. See Table 1.
Subwoofer
The subwoofer is dedicated to the low frequencies (bass), which
require more power. To obtain the best results, most speaker
manufacturers offer powered subwoofers that contain their own
amplifier. Usually, a line-level (nonamplified) connection is made
from the receiver’s Subwoofer Output to a corresponding jack
on the subwoofer, as shown in Figure 3. The AVR 7550HD offers
the option of connecting two subwoofers to independent outputs,
which enables the EzSet/EQ II process to configure each subwoofer
precisely to account for its unique characteristics and placement
within the room.
Table 1 – Connection Color Guide
Audio Connections
Left
White
Right
Red
Front (FL/FR)
Center (C)
Green
Blue
Gray
Tan
Surround (SL/SR)
Surround Back (SBL/SBR)
Subwoofer (SUB)
Brown
Purple
Digital Audio Connections
Coaxial
Although the purple subwoofer outputs look similar to full-range
analog audio jacks, they are filtered to allow only the low frequen-
cies to pass. Don’t connect these outputs to any other devices.
Orange
Optical
Input
Pb
Output
Video Connections
Component
Composite
Y
Pr
Red
Green
Blue
Yellow
S-Video
™
HDMI Connections (digital audio/video)
HDMI
Preout
Subwoofer
Figure 3 – Subwoofer
CONNECTING SOURCE DEVICES
TO THE AVR
Speaker Connections
Speaker cables carry an amplified signal from the receiver’s speaker
terminals to each loudspeaker. They contain two wire conductors,
or leads, inside plastic insulation, that are differentiated in some
way, such as with colors or stripes.
Audio and video signals originate in “source devices,” including
your Blu-ray Disc or DVD player, CD player, DVR (digital video
recorder) or other recorder, tape deck, game console, cable or
satellite television box, MP3 player, USB drive or network device.
The AVR’s tuner also counts as a source, even though no external
connections are needed, other than the FM and AM antennas
and the XM antenna module.
The differentiation preserves polarity, without which low-frequency
performance can suffer. Each speaker is connected to the receiver’s
speaker-output terminals using two wires, one positive (+) and one
negative (–). Always connect the positive terminal on the speaker,
which is usually colored red, to the positive terminal on the receiver,
which is colored as indicated in the Connection Color Guide above
(Table 1). The negative terminals are both black.
Separate connections are required for the audio and video portions
of the signal, except for digital HDMI connections. The types of
connections used depend upon the capabilities of the source device
and video display.
The AVR 7550HD uses binding-post
speaker terminals that can accept
banana plugs or bare-wire cables.
Audio Connections
+
Banana plugs are inserted into the
hole in the middle of the terminal
cap. See Figure 1.
There are two types of audio connections: digital and analog.
Digital audio signals are required for listening to sources encoded
with digital surround modes, such as Dolby Digital and DTS, or for
noncompressed PCM digital audio. There are three types of digital
audio connections: HDMI, coaxial and optical. Do not use more
than one type of digital audio connection for each source device.
However, it’s okay to make both analog and digital audio connec-
tions to the same source.
Figure 1 – Binding-Post Speaker Terminals With Banana Plugs
Bare wire cables are installed as follows (see Figure 2):
1. Unscrew the terminal cap until the pass-through hole is revealed.
2. Insert the bare end of the wire into the hole.
NOTE: HDMI signals may carry both audio and video. If your
video display device has an HDMI input, make a single HDMI
connection from each source device to the AVR. Usually, a
separate digital audio connection is not required. Turn the
volume on your television all the way down.
3. Hand-tighten the cap until the wire is held snugly.
Digital Audio
1
2
3
The AVR 7550HD is equipped with four HDMI (High-Definition
Multimedia Interface) inputs, and one output. HDMI technology
enables digital audio and video information to be carried using
a single cable, delivering the highest quality picture and sound.
Figure 2 – Binding-Post Speaker Terminals With Bare Wires
The AVR 7550HD uses HDMI (V.1.3a with Deep Color) technology
and is capable of processing both the audio and video components
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
of the HDMI data, minimizing the number of cable connections
in your system. The AVR 7550HD implements Deep Color, which
increases by an order of magnitude the shades of color that can
be displayed, and the latest lossless multichannel audio formats,
including Dolby TrueHD and DTS-HD Master Audio.
You may only record materials from DVDs or other copy-protected
sources using analog connections. Remember to comply with all copy-
right laws, if you choose to make a copy for your own personal use.
L
Analog audio
cable (RCA)
R
NOTE: Some DVD-Audio, SACD, Blu-ray Disc and HD-DVD
players only output multichannel audio through their multi-
channel analog outputs. Make a separate analog audio con-
nection in addition to the HDMI connection, which is still used
for video and to listen to Dolby Digital, DTS or PCM materials
that may be stored on the disc.
Figure 7 – Analog Audio
Multichannel analog connections are used with high-definition
sources that decode the copy-protected digital content, such as
some DVD-Audio, SACD, Blu-ray Disc and HD-DVD players. See
Figure 8. The multichannel analog audio connection is not required
for players compliant with HDMI version 1.1 or better, or that output
linear PCM signals via an HDMI connection. Consult the owner’s
guide for your disc player for more information.
The AVR 7550HD converts analog video signals to the HDMI format,
including its on-screen menus, upscaling to high-definition 1080p
resolution.
The HDMI connector is shaped for easy plug-in (see Figure 4). If
your video display has a DVI input and is HDCP-compliant, use an
HDMI-to-DVI adapter (not included). A separate audio connection is
required. HDMI cable runs are limited to about 10 feet.
Front Surround Center
Multichannel
analog audio
cable (RCA)
White
Red
Blue
Gray
Green
Subwoofer
Purple
Figure 4 – HDMI Connection
Figure 8 – Multichannel Analog Audio
If your video display or source device is not HDMI-capable, use one
of the analog video connections (composite, S- or component video)
and a separate audio connection.
The AVR 7550HD also includes a proprietary, dedicated audio con-
nection for The Bridge II docking station for iPod. If you own a dock-
ing iPod (most models, 4G or later), connect The Bridge II (included)
to The Bridge II port on the receiver. See Figure 9. Dock your iPod
(not included) in The Bridge II, and you may listen to your audio
materials through your high-performance audio system. You may
view still images or video materials stored on a photo- or video-
capable iPod that supports video browsing. Use the AVR 7550HD
remote to control the iPod, with navigation messages displayed on
the front panel and on a video display connected to the AVR. The
Bridge II outputs analog audio to the AVR 7550HD, and is available
to the multiroom system.
Coaxial digital audio jacks are usually color-coded in orange.
Although they look similar to analog jacks, you should not connect
coaxial digital audio outputs to analog inputs or vice versa. See
Figure 5.
Coaxial digital
audio cable
Coaxial
Figure 5 – Coaxial Digital Audio
Optical digital audio connectors are normally covered by a shutter
to protect them from dust. The shutter opens as the cable is inserted.
Input connectors are color-coded using a black shutter, while outputs
use a gray shutter. See Figure 6.
Optical
Optical digital
audio cable
THE BRIDGE
Figure 9 – The Bridge II port
Figure 6 – Optical Digital Audio
Analog Audio
Video Connections
Analog connections require two cables, one for the left channel
(white) and one for the right channel (red). These two cables are
often attached to each other. See Figure 7.
Many sources output both audio and video signals (e.g., Blu-ray
Disc or DVD player, cable television box, HDTV tuner, satellite box,
VCR, DVR). In addition to the audio connection, make one type of
video connection for each of these sources (only one at a time for
any source).
For sources that are capable of both digital and analog audio, you
may make both connections.
The analog audio connection is required for multizone operation,
as the AVR 7550HD’s multizone system is not capable of converting
a digital signal to analog format. Use the analog audio connections
even with the Surround Back/Zone 2 speaker outputs, in case
another 2-channel digital audio source is in use in the main listen-
ing area. The AVR 7550HD is only capable of processing one PCM
source at a time.
Digital Video
If you have already connected a source device to one of the HDMI
inputs, you have automatically made a video connection, as the
HDMI signal includes both digital audio and video components.
Analog Video
There are three types of analog video connections: composite video,
S-video and component video.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Composite video is the basic connection most commonly available.
The jack is usually color-coded yellow, and looks like an analog
audio jack. Do not plug a composite video cable into an analog or
coaxial digital audio jack, or vice versa. Both the chrominance
(color) and luminance (intensity) components of the video signal
are transmitted using a single cable. See Figure 10.
The AM loop antenna needs to be assembled. Connect the two leads
to the spring terminals on the receiver. The AM antenna leads have
no polarity, and you may connect them to either terminal. See
Figure 14.
Composite
video cable
Figure 10 – Composite Video
S-video, or “separate” video, transmits the chrominance and lumi-
nance components using separate wires contained within a single
cable. The plug on an S-video cable contains four metal pins, plus a
plastic guide pin. Align the plug correctly when you insert it into the
jack. See Figure 11.
Figure 14 – AM Antenna
To enjoy XM satellite radio, purchase an XM Ready antenna module
and a subscription to the XM service. The XM Mini Tuner and Home
The older Connect-and-Play module is also compatible with the
AVR 7550HD, but it may no longer be available. Although you may
use a module with standard audio connections, labeled for “car
and home use,” you will not be able to enjoy the AVR 7550HD’s
ease of control.
S-video cable
Figure 11 – S-Video
Component video separates the video signal into three compo-
nents – one luminance (“Y”) and two sub-sampled color signals
(“Pb” and “Pr”) – that are transmitted using three separate cables.
See Figure 12.
RS-232 SERIAL PORT
Green
Y
The RS-232 serial port may be connected to an external computer
or control device to allow the external device to transmit control
commands to the AVR. The port is bidirectional, so that the AVR can
transmit status updates to the control device. Connecting and using
the RS-232 port requires technical knowledge, and is best left to
a professional custom installer.
Component
video cable
Pb
Pr
Blue
Red
Figure 12 – Component Video
If it’s available on your video display, an HDMI connection is recom-
mended as the best quality connection, followed by component
video, S-video and then composite video.
NOTES:
• Copy-protected sources are not available at the Component
Video Monitor Outputs.
• Standard and high-definition analog video signals may
be upscaled to 1080i resolution for the Component Video
Monitor Outputs. For improved video performance, consider
upgrading to an HDMI-capable video display with 1080p
resolution.
ANTENNAS
The AVR 7550HD uses separate terminals for the included FM and
AM antennas.
The FM antenna uses a 75-ohm F-connector. See Figure 13.
Figure 13 – FM Antenna
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER PLACEMENT
Optimally, the speakers should be placed in a circle with the listening
position at its center. The speakers should be angled so that they
directly face the listening position.
Green
SUB 1
SUB 2
Purple
Purple
C
FR Red
FL
White
Front Speaker Placement
The center speaker is placed either on top of, below or mounted on
the wall above or below the video display screen.
30°
30°
The front left and right speakers are placed along the circle, about
30 degrees from the center speaker and angled toward the listener.
90°
90°
150°
150°
Place the front left/right and center speakers at the same height,
preferably at about the same height as the listener’s ears. The
center speaker should be no more than 2 feet above or below
the left/right speakers. If you’re using only two speakers with the
AVR 7550HD, place them in the front left and right positions.
SR Gray
SL
Blue
Placement of the surround speakers depends on the number of
speakers in your system.
Green
Brown SBL
SBR
Tan
SUB 1
SUB 2
Purple
Purple (Optional)
C
Figure 16 – Speaker Placement (7.1- or 7.2-Channel System)
FR
FL
White
Red
NOTE: Some speaker manufacturers offer 6.1-channel
speaker systems, for 6.1-channel surround sound formats,
such as Dolby Digital EX, DTS-ES Discrete and Matrix modes
and DTS Neo:6 mode. Using the AVR 7550HD in a 6.1-channel
configuration is not recommended. The 6.1-channel formats
will sound better when played through a 7.1-channel system.
The same surround back channel information is played
through both surround back speakers, but with twice the
power and clarity.
30°
30°
110°
110°
150°
150°
SL
Blue
SR
Gray
To use the AVR 7550HD with a 6.1-channel speaker system,
place the single surround back speaker directly behind the
listener, but do not connect it until after you have run the
EzSet/EQ II procedure for a 5.1-channel system. After the
EzSet/EQ II process finishes, connect the surround back
speaker to the Surround Back Left Speaker Output. Then
follow the directions in the Advanced Features section for
manual setup of the surround back speaker.
Alternate placement
for Side Surround
Left Speaker (Blue)
Alternate placement
for Side Surround
Right Speaker (Gray)
Figure 15 – Speaker Placement (5.1- or 5.2-Channel System)
Subwoofer Placement
Placement of the subwoofers is less critical, since low-frequency
sounds are omnidirectional. Placing each subwoofer close to a wall
or in a corner will reinforce the low frequencies, and may create
a “boomy” sound. Temporarily place one subwoofer where the
listener normally sits, then walk around the room until the low
frequencies sound best. Place the subwoofer in that spot. To place
the optional second subwoofer, you may continue this method for
finding a second optimal location, or place each subwoofer near
the front left and right speakers, as shown in the diagrams.
Placement of Surround Speakers in a
5.1- or 5.2-Channel System
The side surround speakers should be placed 110 degrees from
the center speaker, slightly behind and angled toward the listener.
Alternatively, place them behind the listener, with each surround
speaker facing the opposite-side front speaker. See Figure 15.
The surround speakers may be placed a little higher than the
listener’s ears.
NOTE: Your receiver will sound its best when the same
model or brand loudspeaker is used for all positions.
Placement of Surround Speakers in a
7.1- or 7.2-Channel System
In a 7.1- or 7.2-channel system, the side surround speakers are
placed 90 degrees from the center speaker, directly to either side of
the listening position. The surround back left and right speakers are
placed 150 degrees from the center speaker, or directly facing the
opposite-side front speaker. See Figure 16.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Installing the AVR 7550HD and connecting it to the other system com-
ponents can be complex. To simplify installation, it is suggested that
you design your system before you begin connecting wires and cables.
3. Best video connection for each source: Examine
each source device and write down the best available type of video
connection, but not better than the system-best connection. Leave
blank audio-only sources, such as a CD player.
Although the rear-panel jacks allow for a variety of audio and video
connections to other components, the AVR’s software organizes
the connections into 10 conventional sources: CBL/SAT, DVD, TV,
Game, Media Server, AUX, A, B, C and D. The internal sources (the
tuner, The Bridge II dock for iPod, the USB Port, the Internet Radio
and the Network) will be explained later.
4. Best audio connection for each source: For
each source device, write down the best available type of audio
connection. See the note below, and if the HDMI connection may
be used for audio, it is the best option. The other options, in order
of preference, are: optical digital audio, coaxial digital audio,
2-channel analog audio.
Table A1 in the appendix indicates the default device types for
each source, and the default audio/video connection assignments.
If the defaults suit your system, then connect your devices to the
audio/video inputs shown. Otherwise, design your system as
explained below.
NOTES:
• For multichannel disc players, if both the device and the
TV use HDMI connections for video, then check the owner’s
manual for the device to determine whether it transmits
multichannel audio via its HDMI output. If it does, then no
separate audio connection is required. If not, write down the
multichannel analog audio connection in addition to any
other audio type.
1. Best video connection type for your system:
Examine the video inputs on your TV or video display. Write down
the best available video connection type here: ____________.
The options, in order of preference, are: HDMI, DVI (must be HDCP-
compliant), component video, S-video or composite video. This is
the “system-best” video connection for your system.
• If the device uses an HDCP-compliant DVI output for video,
then connect it to one of the AVR’s HDMI Inputs using an
HDMI-to-DVI adapter, but a separate audio connection will
always be required.
2. Decide which source will be used for each
device: Match up to 10 devices to the 10 conventional sources
listed in the Table 2 worksheet below. Use the AUX source for any
of these device types: CD player, HDTV set-top box, personal video
recorder (PVR), TiVo device or VCR. The A, B, C and D sources were
added to the AVR 7550HD to enable you to benefit from the wide
variety of audio and video inputs available, and these sources may
be used for any device type.
5. Decide which sources to connect to each of
the video inputs: Assign only one unique video input to each
source, except that you may add a composite video connection to
make the source’s video signal available to the multizone system.
Use the best type of video connection available for each source.
• If your system-best video connection is “HDMI”, select up to
four HDMI source devices and assign them to one of the four
numbered HDMI Inputs.
NOTE: You may match any device type to any source. The
device type is only relevant for programming control codes
into the handheld remote and, as explained on page 27, you
may reassign any Source Selector’s device type. Any audio or
video source may be connected to any matching jack on the
AVR, regardless of device type.
• If your system-best video connection is “Component”, or if you
have source devices with component video outputs that weren’t
assigned to one of the HDMI Inputs, assign up to three devices
to one of the three numbered Component Video Inputs.
Table 2 – Source Assignment Worksheet
Source
Device Type Best Video
Connection
Video Input Second Composite Best Audio
Audio Input
Assigned (may
be one digital
Analog Audio
Input for
Recording or
Assigned
Video Input for
Multizone
Connection
(HDMI, Optical,
Coaxial, 2-Ch
(HDMI, DVI,
Component,
Operation
plus one or more Multizone
S-Video,
Composite)
Analog, 6-/8-Ch analog)
Analog)
Operation
Cable/SAT
DVD
TV
Game
Media Server
AUX
A
B
C
D
22
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
• If your system-best video connection is “S-video”, or if you have
source devices with S-video outputs that have not been assigned
to an HDMI or Component Video Input, then assign up to three
devices to one of the three numbered S-video Inputs.
• If your system-best video connection is “Composite Video”, or if
you have source devices with composite video outputs that have
not been assigned to any other video input, then assign up to three
devices to one of the three numbered composite video Inputs.
NOTE: If the source device is a video recorder that will
be used to record from other devices connected to the AVR,
assign the recorder to the Composite or S-Video Video 2
Input, which has a recording output. Any of the Coaxial or
Optical Digital Inputs may be assigned to the recorder for
audio, if it is capable of making digital audio recordings. To
make analog recordings, assign either the Analog 3 or 4 Audio
Inputs to the recorder, as both have recording outputs. It is
not necessary to connect TiVo or PVR devices that will only
record from their direct cable or satellite television signals to
the AVR’s recording outputs.
6. Decide which audio inputs to connect to each
source: Assign only one unique digital audio input to each digital
source. Assign analog audio inputs to analog sources, or as second-
ary connections for digital sources for backup, for recording or to
make the source available to the multizone system.
• Any source using an HDMI Input requires no additional connection
for audio unless:
N
The source doesn’t output multichannel audio through its HDMI
output. Make a second connection to the 6-/8-Channel Analog
Audio Inputs.
N
The source has an HDCP-compliant DVI output for video only.
Assign a digital or analog audio input.
• For any source whose best audio connection is optical or coaxial
digital audio, assign one of the four Optical or four Coaxial Digital
Audio Inputs. Do not connect both types of digital audio to the
same source device.
• You may assign one of the 2-Channel Analog Audio Inputs to
a digital source.
• You may also assign the 6-/8-Channel Analog Audio Inputs,
if available, to a digital source.
• Assign one of the six 2-channel Analog Audio Inputs to an
analog source.
NOTE: If the source device is a digital audio recorder, it may
be used with any of the Coaxial or Optical Digital Audio Inputs
and Outputs. Both coaxial and optical signals are available at
either digital audio output. To make analog recordings, assign
either the Analog 3 or 4 Audio Inputs to the recorder, as both
have recording outputs.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
You are now ready to begin installing the AVR. Before beginning to
connect the various components to the receiver, turn off all devices,
including the AVR 7550HD, and unplug their power cords. Don’t
plug in any of the power cords until you have finished making
all of your connections.
STEP FIVE – Connect FM Antenna
Connect the included FM antenna to the 75-ohm FM antenna terminal.
STEP SIX – Connect AM Antenna
Assemble the included AM antenna (see Figure 17) and connect it
to the AM and Ground antenna terminals. The antenna is not polar-
ized, and either lead may be connected to either terminal.
The receiver generates heat. Select a location that leaves several
inches of space on all sides. Avoid completely enclosing the receiver
inside an unventilated cabinet. Place components on separate
shelves rather than stacking them directly on top of the receiver.
Never block the AVR’s ventilation slots on the top and side panels.
Doing so could cause the AVR to overheat, with potentially serious
consequences. Some shelf surface finishes are delicate. Try to
select a location with a sturdy surface finish.
TIP: Label each cable before connecting it, to avoid mistakes.
Write a description of the cable on a blank adhesive label,
e.g., “DVD”, and fold the label around the cable about 6 inches
from the end to be plugged into the AVR.
Figure 17 – AM Antenna Assembly
STEP SEVEN – Connect XM Antenna
Module
If you have purchased an optional XM antenna module designed
for XM Ready® devices, plug it into the XM jack. Purchase a
subscription and activate the module, following the instructions
a south-facing window.
Almost all of the following installation steps are optional, depending
on your system. Skip any step that does not apply to your system.
STEP ONE – Connect Source Devices
Leaving all AC power cords unplugged, connect the source devices
to the AVR using the audio and video inputs you assigned in Table 2.
STEP EIGHT – Connect USB Device
STEP TWO – Connect TV
To play MP3 or WMA audio files or JPEG still-image files stored on
a USB storage device, connect the device to the front-panel USB
Port, using a cable or connector that is attached to the device or
provided by you.
Connect the system-best video input on the TV to the corresponding
video monitor output on the AVR.
STEP THREE – Connect Loudspeakers
After you have placed your loudspeakers in the room as explained
on page 21, connect each speaker to its color-coded terminal on
the AVR. Maintain proper polarity by connecting the negative terminal
on the speaker (usually colored black) to the negative terminal on
the AVR (also colored black); and the positive terminal on the speaker
(usually red) to the positive terminal on the AVR (color varies by
channel; see Table 1 on page 18).
STEP NINE – Connect AVR to Internet
To use the AVR’s internal Internet Radio tuner to listen to MP3 or
WMA audio streams, connect the Network Jack to the Ethernet port
on a router or modem that has Internet access, a home network,
or directly to a PC. You may need to contact your Internet service
provider (ISP), or the manufacturer of your router, to obtain the
information necessary to set up the network connection. See
pages 36 and 37.
If you have a subwoofer, connect its line-level or LFE input to the
purple Subwoofer 1 Output. An optional second subwoofer may be
connected to the Subwoofer 2 Output.
STEP TEN – Connect Remote IR Inputs
and Outputs
The AVR 7550HD is equipped with a Remote IR Input, a Zone 2
Input and both full-carrier and stripped Remote IR Outputs to facilitate
use of your system with a remote control in a variety of situations.
NOTE: If the subwoofer only has speaker-level inputs, after
you have configured the AVR using EzSet/EQ II technology as
described on page 29, connect the subwoofer’s left and right
speaker input terminals to the AVR’s Front Left and Front Right
Speaker Outputs, then connect the front left and right main
speakers to the subwoofer’s left and right speaker output
terminals. Consult the owner’s manual for the subwoofer for
specific installation instructions.
When the AVR 7550HD is placed inside a cabinet or facing away
from the listener, connect an external IR receiver, such as the
optional Harman Kardon HE 1000, to the Remote IR Input jack. For
multizone operation, connect an optional IR receiver, keypad or
other control device to the Zone 2 IR Input for remote control of the
AVR 7550HD (and any sources connected to the AVR’s Remote IR
Output) from the remote zone. Signals transmitted through the Zone 2
IR Input will control source selection and volume for the main or
remote zone, depending on the setting of the remote’s Zone Selector.
If a source device is shared with the main listening area, any control
commands issued to that source will also affect the main room.
STEP FOUR – Connect
Dock
To enjoy content stored on a compatible iPod (not included), con-
nect The Bridge II dock (included) to its proprietary connector.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
If any source devices are equipped with a compatible Remote IR
Input, use a 1/8-inch mini-plug interconnect cable (not included)
to connect the AVR’s Remote IR Output to the source device’s
Remote IR Input.
Your main system will be limited to 5.2 channels, affecting playback
of programs recorded in 6.1 or 7.1 channels.
C. Connect an external amplifier to the Surround
Back/Zone 2 Preamp Outputs. This method requires an
additional amplifier, but may increase the total number of remote
rooms when used with methods A and B.
The AVR 7550HD outputs a “stripped carrier” IR signal through the
Remote IR Output, but a full-carrier IR signal is available at the
Carrier Remote IR Output. The Carrier Remote IR Output is only
available to one sender at a time, which is assigned in the AVR’s
Zone 2 menu. Depending on whether you select Zone 2, Front or
A-BUS, the Carrier Remote IR will only transmit commands received
from the Zone 2 IR Input, the front-panel IR receiver or the A-BUS
system to a device connected to it. This avoids having conflicting
control commands sent to a device from listeners in different areas
of the home.
D. Connect an A-BUS hub or other A-BUS com-
ponents to the A-BUS port. Use Category 5/5e cable,
as described in the instructions for your A-BUS components. The
A-BUS system carries the audio signal to the remote components,
while receiving IR control codes. A hub may distribute audio to
many remote rooms. To control source devices exclusively from the
remote A-BUS module, connect the AVR’s Carrier Remote IR Output
to a compatible IR input on the source, and assign the full-carrier
output to the A-BUS system in the AVR’s Zone 2 menu. This avoids
having conflicting control commands sent to a source intended for
the A-BUS system.
To control more than one source device through the Remote IR
Output, connect all sources in “daisy chain” fashion, connecting
each device’s IR output to the next device’s IR input, starting with
the AVR. Connect devices expecting a full-carrier IR signal to the
Carrier Remote IR Output, and assign the desired sending zone in
the Zone 2 menu. Use the Remote IR Output for devices expecting
a stripped signal.
IR commands received from the A-BUS system are also
distributed to the AVR’s other IR outputs. Visit the Web site
Harman Kardon hubs, the ABH 4 and ABH 4000, and amplified
in-wall modules, the AB 1 and AB 2.
STEP ELEVEN – Install a Multizone System
The AVR 7550HD offers several methods of distributing audio to
other areas in your home, and it also features video distribution.
Connect a Video Display Device or
Switcher
To add video distribution to your multiroom system, connect the
Multizone Video Output either directly to the video display in the
remote room or to any optional video distribution switchers or
amplifiers that may be required.
IMPORTANT SAFETY NOTE: Installing a multizone
system typically requires running cables inside walls. Always
comply with the appropriate safety codes when installing
concealed wiring, particularly all applicable state and local
building codes and the NEC (National Electrical Code). Failure
to do so may present a safety hazard. If you have any doubt
about your ability to work with electrical and telecommunica-
tions wiring, hire a licensed electrician or custom installer to
install the multizone system.
NOTES:
• Only composite video is output to the multizone system.
• S-video, component or HDMI video sources may not be routed
through the multizone system. Make a second, composite
video connection for the multizone system.
When the system is installed using method B or C below, multizone
operation takes over the Surround Back/Zone 2 amplifier channels,
limiting the system in the main listening room to 5.2 channels.
• When connecting the AVR 7550HD to the remote room’s
video display, distance limitations may exist for composite
video connections. Although the use of low-loss coax cables
may reduce signal loss, optional distribution amplifiers may
occasionally be required when long cable runs are used.
Select one or all of these methods for audio
distribution:
A. Connect an external amplifier to the Zone 2
Audio Outputs. It is recommended that you place the amplifier
in the same room as the AVR 7550HD so that a shorter length of
interconnect cable is used with a long run of speaker wire to the
remote room. A long run of interconnect cable would be subject to
signal degradation. Depending on your amplifier, distribute the
audio signal to a single pair of speakers, or to several pairs placed
in different rooms.
Connect IR Control Devices to the Zone 2
IR Input
For methods A, B and C, connect an IR control device to the Zone 2
IR Input for remote-room control of the multizone system, source
devices and volume in the remote zone. An A-BUS system does
not require a separate IR control connection.
The Zone 2 Audio Outputs offer the benefit of 7.2-channel audio in
the main room simultaneously with multizone operation. However,
the benefit is achieved with the expense of an additional compo-
nent, i.e., the amplifier.
NOTE: Only analog audio sources are available to the multi-
zone system. For digital sources, make a second, analog audio
connection. The USB, The Bridge II and Internet Radio sources
are available to the multizone system.
B. Connect the remote room’s speakers directly
to the Surround Back/Zone 2 Speaker Outputs.
Reassign the Surround Back amplifier channels to power the
speakers (see page 47).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
the Harman Kardon DMC 1000 digital media center and TVs.
It is also preprogrammed to operate your iPod when docked in
The Bridge II.
STEP TWELVE – Plug in AC Power Cords
Before plugging the AVR into an unswitched electrical outlet, make
sure the Main Power Switch behind the front-panel door is off, to
prevent the possibility of damaging the AVR in case of a transient
power surge. When pressed in, the switch is on. When pressed
again to unlatch it, the switch pops out.
To access the functions for a particular device, switch the remote’s
device mode. Press the AVR Settings Button to access the codes
that control the receiver, or the Source Selector Buttons to access
the codes for the devices programmed into the remote.
You may plug one device that draws no more than 50 watts into
the AC Switched Accessory Outlet on the rear panel. Turn on the
device’s mechanical or master power switch, and that device will
power on any time the AVR 7550HD is turned on (some devices may
require additional steps to power on from their standby mode). If the
device has a clock or must always be on (such as a cable set-top
box programmed to make recordings), do not plug it into this outlet.
To program the codes for a source device into
the remote:
1. Turn on the source device.
2. Access the remote’s menu system by pressing and holding the
AVR Settings Button for 3 seconds, until the “Main Menu” and
“Program Device” messages appear in the LCD Display.
The AVR 7550HD is equipped with a detachable power cord, allow-
ing you to fully wire your system before installing the AVR. Plug the
male end of the cord into an unswitched AC outlet, and the female
end into the AVR 7550HD.
3. Press the OK Button to select the Program Device function.
4. Use the 1/5Buttons to select the Source Selector (or device)
to program, and press the OK Button when the desired device
appears on the lower line of the LCD Display.
It is recommended that you copy the appropriate information from
the Table 2 worksheet to Table A5 in the appendix for future refer-
ence, in the event changes are made to the system components.
5. For two of the Source Selectors and for sources A, B, C and D,
the next step requires you to specify the device type. For the
other Source Selectors, proceed to step 6.
STEP THIRTEEN – Insert Batteries in
Remote
• Cable/SAT: Use the 1/5Buttons to select either a cable
television or satellite television set-top box, and press the OK Button.
The AVR 7550HD remote control uses four AAA batteries (included).
• AUX: Use the 1/5Buttons to select a CD player, HDTV set-top
box, PVD (personal video device, such as a DVR), TiVo system or
VCR. Press the OK Button when the desired device appears.
To remove the battery cover located on the back of the remote,
squeeze the tab and lift the cover.
• A, B, C, D: Select any desired device type.
Insert the batteries as shown in Figure 18, observing the correct
polarity.
6. Select whether to program the device manually or use the
remote’s Auto Search capability. Manual programming simply
requires you to select the brand name of your device and try a
handful of possible codes. There is no need to look up numeric
codes; the AVR 7550HD does the work for you. It is recommended
that you select Manual programming first.
• Manual Programming: Use the 1/5Buttons to scroll
through the list of brands for which the remote has codes stored
in its library. When your brand appears on the lower line, press the
OK Button.
Figure 18 – Remote Battery Compartment
The remote will look up the brand in its library and display the
number of codes available. Press the “1” Alphanumeric Key first.
The remote will transmit the Power Off command associated
with the first code set to the device. If the device turns off, then
a compatible code set has been found. Press the OK Button to
accept it.
Point the remote’s lens toward the front panel of the AVR 7550HD.
Make sure no objects, such as furniture, are blocking the remote’s
path to the receiver. Bright lights, fluorescent lights and plasma
video displays may interfere with the remote’s functioning. The
remote has a range of about 20 feet, depending on the lighting
conditions. It may be used at an angle of up to 30 degrees to either
side of the AVR.
If the device remains powered on, press the “2” Alphanumeric Key.
Proceed in this fashion until either a compatible code set is found,
or you run out of codes for that brand.
Leave the Zone Selector Switch at the bottom in the Zone 1 position
for normal use.
If you run out of codes, press the Back/Exit Button to end the
process, and repeat steps 2 through 5. At step 6, select Auto
and follow the instructions in the next bullet.
If the remote seems to operate intermittently, or if pressing a button
on the remote does not cause the AVR Settings Button or one of the
Source Selectors to light, check or replace the batteries.
• Auto Programming: Wait for the remote to retrieve its
entire library of codes for the device type. You will have to press
the 1/5Buttons to transmit every code for the device type until
a compatible code set is found.
STEP FOURTEEN – Program Sources Into
the Remote
The AVR 7550HD remote may be programmed to control many
brands and models of DVD players, cable boxes, satellite receivers,
26
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
7. When a compatible code set is found, press the OK Button to
program it into the Source Selector.
Buttons, OK Button, Disc Menu Button, the four Soft Keys,
Channel Up/Down, Volume Up/Down, Mute and the Transport
Controls (including Record).
8. Check that other functions control the device correctly. Sometimes
manufacturers use the same Power code for several models,
while other codes vary. Repeat this process until you’ve pro-
grammed a satisfactory code set that operates most functions.
NOTE: If you press the wrong destination button and wish to
cancel the learning process, you must wait about 30 seconds
for the remote to “time out”. It will exit its program mode and
return to normal operation, and you may begin again. Pressing
another button will have no effect.
To change the device type of a Source Selector:
If your system includes two products of one device type but no
product corresponding to a different Source Selector, you may
program one product into its corresponding Source Selector, and
change another Source Selector’s device type to program the
second product by following this procedure:
7. Press the key on the original remote, and if the code was learned
correctly, the Navigation and OK Buttons will light up. The Learn
Menu will prompt you to learn another key, rename the key just
learned or exit Learn mode. Use the 1/5Buttons to make your
selection, and press the OK Button.
1. Access the remote’s menu system by pressing and holding the
AVR Settings Button for 3 seconds, until the “Main Menu” and
“Program Device” messages appear in the LCD Display.
To delete a programmed or learned code:
1. Access the remote’s menu system by pressing and holding the
AVR Settings Button for 3 seconds, until the “Main Menu” and
“Program Device” messages appear in the LCD Display.
2. Use the 1/5Buttons to select “Change Device Type” from the
remote’s main menu, and press the OK Button.
3. Use the 1/5Buttons to select the Source Selector whose device
type you wish to change, and press the OK Button. Your selection
will appear on the left side of the lower line, while the choice of
new device types will appear on the right side.
2. Use the 1/5Buttons to select “Learn” from the remote’s main
menu, and press the OK Button.
3. When the “Learn Menu” message appears in the upper line of
the LCD Display, scroll to the “Learn Delete” option, and press
the OK Button.
4. Use the 1/5Buttons to select the new device type you wish to
assign to the Source Selector, and press the OK Button.
4. The Learn Delete menu offers the options of deleting a single
learned key code, an entire device or all devices. Scroll to the
desired option and press the OK Button.
5. Program your product into the Source Selector by choosing the
brand, then searching for a compatible code set, as described in
the preceding section. If you allow the remote to “time out”, then
the device type reassignment will not take effect.
• To delete an individual key code, the remote will first prompt
you to select the device containing the key code, then prompt
you to press the key. It will confirm the deletion, then offer
you the opportunity to delete another learned key or exit the
delete key function.
To “ learn” individual key codes:
If some functions do not work correctly, you may reprogram individual
keys from the device’s original remote by following this procedure:
• To delete an entire device, the remote will prompt you to
select the device. When you scroll to the device and press
the OK Button, the remote will confirm the deletion and exit
its programming mode, returning to normal operation.
1. Place the two remotes with their IR transmitters facing each
other, about one inch apart. See Figure 19.
• To delete all devices, wait a few moments while the remote
deletes all programmed device codes. It will then return to
normal operation.
Figure 19 – AVR and Device Remotes “Head to Head”
2. Access the remote’s menu system by pressing and holding the
AVR Settings Button for 3 seconds, until the “Main Menu” and
“Program Device” messages appear in the LCD Display.
To rename a key or device:
If you wish to change the name of a device or key as it appears in
the LCD Display, follow these steps:
3. Use the 1/5Buttons to select “Learn” from the remote’s main
menu, and press the OK Button.
1. Access the remote’s menu system by pressing and holding the
AVR Settings Button for 3 seconds, until the “Main Menu” and
“Program Device” messages appear in the LCD Display.
4. When the “Learn Menu” message appears in the upper line of
the LCD Display, make sure the “Learn” message appears in the
lower line (not “Learn Delete”), and press the OK Button.
2. Use the 1/5 Buttons to select “Rename” and press the OK Button.
3. Use the 1/5 Buttons to select whether to rename a device or a
key, and press the OK Button.
5. Use the 1/5Buttons to select the device you wish to learn a
code for, and press the OK Button.
4. Use the 1/5 Buttons to select the device, either to rename the
device itself or a key function used by that device, and press the
OK Button.
6. Press the destination button, and the menu will prompt you to
press the key on the original remote whose code you wish to
program into the destination button. You may learn a new code
into the following buttons: Device Power On/Off, Alphanumeric
Keys, Last Button, Back/Exit Button, Menu Button, Navigation
5. The current name of the device or key will appear on the lower
line of the LCD Display, with the cursor at the end of the line.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Use the 7Button to move the cursor to the beginning of the name,
then type over the current name using the Alphanumeric Keys.
Each Alphanumeric Key has the characters available in addition
to its number printed above the key. Each press of the key
scrolls through the available characters. To move to the next
character, either press the 3Button or press the next desired
Alphanumeric Key.
Press the OK Button to finish, and the remote will prompt you to
rename another key or device, or to exit.
STEP FIFTEEN – Turn On the AVR 7550HD
Two steps are required the first time you turn on the AVR 7550HD.
1. Flip down the Front-Panel Door and press the Main Power Switch
in. The Power Indicator on the front panel will turn amber, indi-
cating that the AVR is in Standby mode and is ready to be turned
on. Normally, you may leave the Main Power Switch on, even
when the receiver is not being used.
2. There are several ways to turn on the AVR from Standby mode.
a) Press the Standby/On Switch on the front panel.
b) Using the remote, press the AVR Power On Button or any of
the Source Selectors.
NOTES:
• Any time you press one of the Source Selectors on the
remote, the remote will switch device modes. To control the
receiver, press the AVR Settings Button. Some AVR functions
are available in all device modes: Volume Controls (including
Mute), Audio Effects, Video Modes, Surround Modes, AVR
Settings, Info Settings, Sleep Settings and AVR Power On
and Off.
• If you do not see a picture within about 1 minute, refer to
the Video Troubleshooting Tips on page 34.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
In this section, you will configure the AVR 7550HD to match your
actual system. A video display must be connected to one of the
video monitor outputs on the receiver.
Until recently, most receivers required manual calibration and
configuration, a tedious process that called for a good ear or the
purchase of an SPL (sound-pressure level) meter. Although you may
configure the AVR 7550HD manually, as described in the Advanced
Functions section, it is recommended that you take advantage of
the signature Harman Kardon EzSet/EQ II system.
USING THE ON-SCREEN MENU SYSTEM
Although it’s possible to configure the AVR using only the remote
and the front-panel messages, it is easier to use the full-screen
menu system.
Eliminate extraneous background noise, such as noisy air conditioning.
Avoid making any loud noises while running EzSet/EQ II setup.
The menu system is accessed by pressing the AVR Settings Button
on the remote or front panel.
IMPORTANT SAFETY NOTE: During the EzSet/EQ II
procedure, a series of very loud test sweeps will be played
through all of the speakers. Avoid sitting or standing close to
any one speaker during the procedure. If you are particularly
sensitive to loud noises, you may wish to leave the room and
have someone else run the EzSet/EQ II process.
The Main Menu will appear (see Figure 20), and if a video source
is playing, it will be visible behind the transparent menu.
STEP ONE – Place the included EzSet/EQ II microphone
in the listening position or in the center of the room, at about
the same height as the listeners’ ears. The microphone features
a threaded insert on the bottom, for mounting on the included
extension rod or a camera tripod.
Figure 20 – Main Menu
STEP TWO – Plug the EzSet/EQ II microphone into the
EzSet/EQ II Microphone Input Jack on the front of the receiver,
and set the level control on the subwoofer to the halfway point.
NOTE: When using the AVR’s on-screen menu system, a
video output resolution of 720p or higher is recommended
for best legibility, and to provide graphics that simplify some
configuration options. Depending on the resolution selected,
the menus shown by your system may vary in appearance.
STEP THREE – Turn on the AVR 7550HD and the video
display. Press the AVR Settings Button to display the Main Menu.
Use the 5Button to highlight the Speaker Setup line, then press
the OK Button. See Figure 21.
The main menu system consists of five submenus: Source
Selection, Setup Source, Speaker Setup, Zone 2 and System.
Use the 1/57/3Buttons on the remote or front panel to navigate
the menu system, and press the OK Button to select a menu or
setting line, or to enter a new setting.
The current menu, setting line or setting will appear in the Message
Display, as well as on screen.
To return to the previous menu or exit the menu system, press the
Back/Exit Button. Be certain all settings are correct, as any changes
you have made will be retained.
Most users should follow the instructions in this Initial Setup section
to configure a basic home theater system. You may return to these
menus at any time to make additional adjustments, such as those
described in the Advanced Functions section.
Figure 21 – Speaker Setup Menu Screen
Select “Automatic Setup-EzSet/EQ II”.
To return to the Speaker Setup menu without starting the EzSet/EQ II
process, select Back. When you are ready to begin, select Continue.
To manually program the speaker crossover settings before the
EzSet/EQ II test is run, select Manually Set Crossovers. It is recom-
mended that you allow the EzSet/EQ II process to detect the crossovers
and only adjust them manually if you have previously run the EzSet/EQ II
test and you wish to change the settings to obtain different results.
Before beginning initial setup, all loudspeakers, a video display and
all source devices should be connected. You should be able to turn
on the receiver and view the main menu when you press the AVR
Settings Button. If necessary, reread the Installation Section and the
beginning of this section before continuing.
Configure the AVR 7550HD, Using
EzSet/EQ II Technology
NOTE: The AVR 7550HD will automatically set its master
volume to – 25dB.
One of the most important steps in setting up a home theater
system is to calibrate the receiver to match the loudspeakers,
optimizing sound reproduction.
STEP FOUR – After you select “Continue”, the test will
begin. Maintain silence during the EzSet/EQ II configuration.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
As the EzSet/EQ II system tests each speaker, its position will appear
on screen. If the test sweep is heard from a different speaker than
the one indicated on screen, turn off the AVR and check the speaker-
wire connections, then begin again.
Audio Effects: Displays the Audio Effects submenu, where
you may adjust the Dolby Volume setting, the bass and treble tone
controls, and the LFE trim, or you may select the EzSet/EQ II listening
position. These settings affect each source independently. Leave
this submenu at its default settings, and return to it later if your
system requires fine-tuning. See the Advanced Functions section
for more information.
When the Speaker Detection test is completed, select the Continue
option. The results will be displayed, along with these options:
• The Retest option repeats the EzSet/EQ II process. Increase the
master volume manually, if some speakers were not correctly
detected.
Video Modes: Displays the Video Modes submenu, where you
may make picture adjustments for each source independently. Leave
the settings at their factory defaults. Picture adjustments should be
made to your video display first, with this menu used only for fine-
tuning. See the Advanced Functions section for more information.
• Select Cancel to return to the Speaker Setup menu.
See the Advanced Functions section for instructions on how to
manually configure the speakers or manually adjust the settings
established by the EzSet/EQ II process.
Surround Modes: Displays the Surround Modes submenu,
where you may program surround modes for analog movies, music
and games for each source independently.
During the Near Field test, follow the instructions that appear on
screen. You may be directed to hold the microphone about 2 feet
away from some speakers.
Digital surround signals, such as Dolby Digital and DTS, are auto-
matically played in their native formats, although you may change
the surround mode. See the Advanced Functions section for more
information.
When the test is finished, you will be given the option of saving
the EzSet/EQ II test results in one of two “listening positions”, or
not saving the results at all. The purpose is to allow you to run the
EzSet/EQ II tests for two different frequently used listening positions
within the room to optimize performance, depending on how you
use the room.
Audio Format From Source: This line is informational
only. When a digital program is playing, its format will be identified
here. When analog audio programs are playing, this line displays
ANALOG.
After the results have been saved, the menu for manual adjustment
of the listening position settings will appear. See the Advanced
Functions section for instructions on manually adjusting the speaker
settings.
Audio and Video Input Selection
See Table A2 in the appendix for the factory default input assignments
for each source. You may assign any available input to any source
using the Info Settings menu.
If you do not save the results, you may go back and repeat the
EzSet/EQ II test.
When a source is selected, the AVR will check the assigned digital
audio input for a signal. If one is present, the digital input will be
selected. If not, the AVR will select the analog audio input specified
at the Audio Auto Polling line of the Info Settings menu. If you don’t
want the AVR to select an analog audio input for the source, leave
this setting at its default of Off.
You may adjust the settings for either listening position, or repeat
the EzSet/EQ II test, from the Speaker Setup menu (Figure 21).
Set Up Sources
The Info Settings menu is used to assign the correct physical audio
and video connections to each source.
The AVR will also select the assigned video source. The only “audio-
only” sources on the AVR 7550HD are the Radio, The Bridge II
(video may be available; see page 37), USB, the Network and
Internet Radio, which use special on-screen menus. If no video
signal is present, the display will remain black. You may pair an
audio device with an A/V device’s video signal using the Info
Settings menu. Sources may share audio or video inputs.
The following settings are not optional and must be adjusted now
to enable playback of each source: Video Input From Source, Audio
Input From Source and Resolution to Display. The other settings
may be adjusted later.
To display the Info Settings menu, press the Info Settings Button
(front panel or remote). Or, from the Main Menu, select the Setup
Source line and select a source from the slide-in menu. A screen
similar to the one shown in Figure 22 will appear.
NOTE: The Bridge II obtains its audio and video signals
(when available) from the iPod docked in it, and it may not
be used with other audio or video sources.
Video Input From Source: Assign the correct video
input. Refer to Table 2, where you noted the physical video input
the source is connected to, and select that input here.
Audio Input From Source: Assign the correct analog or
digital audio input. Refer to Table 2, where you noted the physical
audio input the source is connected to, and select that input here.
If both analog and digital audio connections were made, select the
digital input here, and select the analog input at the Audio Auto
Polling and Zone 2 Audio lines below.
Figure 22 – Setup Source Menu
30
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
6-/8-Channel Inputs
Resolution to Display: This setting reflects the video
output resolution, which is dependent upon the capabilities of the
video display.
The 6-/8-Channel Analog Audio Inputs are used when playing
certain multichannel discs (DVD-Audio, Blu-ray Disc, SACD and
HD-DVD) on a player that decodes the audio and outputs it via its
multichannel analog audio outputs but not via its HDMI output.
• If the display is connected to the AVR’s HDMI Output, the two
devices will communicate with each other, and the AVR will auto-
matically select the best available video output resolution.
HDMI-Equipped Multichannel Disc Player:
• Connect the player’s HDMI output to one of the AVR’s HDMI
Inputs. No other connections are necessary.
• If the display is connected to the AVR’s Component Video Outputs,
there is no automatic detection of the display’s capabilities, and
the video output resolution must be manually adjusted to match
the display’s capabilities (which may be obtained from the display’s
manual or its manufacturer’s Web site).
• Assign the HDMI Input to both the Audio and Video Input From
Source settings.
• If the display is connected to the AVR’s Composite or S-Video
Monitor Output, the video output resolution must be set to 480i
(the factory default) to view any content, including the AVR’s own
menus.
HDMI-Equipped Multichannel Disc Player
That Does Not Output Multichannel Audio
via an HDMI Connection:
• Connect the player’s HDMI output and its multichannel analog
audio outputs to one of the AVR’s HDMI Inputs and to the AVR’s
6-/8-Channel Analog Audio Inputs.
Adjust the resolution by pressing the front-panel Resolution Button
and using the 1/5Buttons until the correct setting appears in the
front-panel Message Display. For composite and S-video, the correct
setting is 480i. For component video, it is the highest resolution
where a picture is visible. You will be prompted to accept or cancel
the resolution change; the CANCEL message will appear on the front
panel with a timer countdown. Press the 5Button to view the ACCEPT
option before the timer reaches 0, and then press the OK Button.
• Assign the HDMI Input to both the Audio and Video Input From
Source settings.
• When listening to DVD-Video discs, CDs or other materials out-
putting standard-definition digital audio, do nothing, as long as
the HDMI Input is assigned to the Audio Input From Source setting.
• To listen to high-resolution multichannel discs, change the Audio
Input From Source setting to “6/8 Channel”. Change it back to the
HDMI Input to listen to standard-resolution digital materials.
NOTE: When the display has a DVI input which is connected
to the AVR using an HDMI-to-DVI adapter, the picture will be
distorted or blank if the display is not HDCP-compliant. In that
case, a different video connection must be used (component,
composite or S-video).
Multichannel Disc Player Without HDMI Output,
or When Video Display Has No HDMI Input:
• Connect the player’s component video outputs to one set of
Component Video Inputs on the AVR. Depending on the capabili-
ties of the player and your video display, you may need to use
a composite or S-video connection instead.
Resolution From Source: Informational only. Indicates
the resolution of the video output by the source device.
HDMI Bypass: When an HDMI source signal is in use and
the system includes an HDMI-capable display, the HDMI Bypass
mode passes the source signal directly to the HDMI Output, bypass-
ing all video processing within the AVR, including video output reso-
lution adjustment. To allow the AVR to process all video, including
“blending” the source video with its on-screen messages and
menus so that you may adjust the AVR without missing any portion
of the program, turn this setting off. When the HDMI Bypass mode
is on, it is not possible to “blend” the video source signal with the
AVR’s on-screen menus. When any remote or front-panel buttons
are pressed, the AVR will momentarily exit HDMI Bypass mode and
display the on-screen menu on a black background. After the menu
is cleared from the screen, either by timing out or when the Back/Exit
Button is pressed, the AVR will return to HDMI Bypass mode.
• Connect the player’s digital audio output to a digital audio input
on the AVR.
• Connect the player’s multichannel audio outputs to the AVR’s
6-/8-Channel Analog Audio Inputs.
• Assign the correct digital audio and analog video inputs to the
Audio and Video Input From Source settings.
• When listening to DVD-Video discs, CDs or other materials out-
putting standard-definition digital audio, do nothing, as long
as the correct digital audio input is assigned to the Audio Input
From Source setting.
• To listen to high-resolution multichannel discs, change the Audio
Input From Source setting to “6/8 Channel”. Change it back to the
digital audio input to listen to standard-resolution digital materials.
Change Name: Change the display name for your source,
which is useful if your source’s device type is different from the
available source names. Select this line and use the 1/5Buttons
to scroll forward or reverse through the alphanumeric characters.
When the desired character appears, use the 3Button to move the
cursor to the next position. Move the cursor again to leave a blank
space. When you have finished, press the OK Button. The name will
appear on the front panel and next to its original name, e.g., DVD,
throughout the on-screen menu system. To clear the entry without
making any changes, scroll to the blank character before “A”.
NOTE: The AVR is capable of processing the signal received
at the 6-/8-Channel Analog Audio Inputs. With these inputs
selected, press the Audio Effects Button to view the Audio
Effects menu. Change the Tone Control setting to “On”, and
you may adjust the Dolby Volume setting, the tone controls or
the EzSet/EQ II settings. With the Tone Control setting off, the
AVR will pass the incoming signal directly to the volume control,
without digitizing or processing it.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
Press the Back/Exit Button, then return to the Setup Source line
of the Main Menu to configure the next source. When you have
finished, press the Back/Exit Button to clear the menus from view.
Adjust Lip Sync: Resynchronizes the audio and video
signals from a source to eliminate a “lip sync” problem. Lip sync
issues can occur when the video portion of a signal undergoes
additional processing in either the source or the video display.
The Lip Sync adjuster appears by itself, enabling you to view the
video while listening to the audio. Use the 7/3Buttons to delay
the audio by up to 180ms. See Figure 23.
You are now ready to begin enjoying your new receiver!
Figure 23 – Adjust Lip Sync
Input Level From Source: This setting defaults to 0dB
for all sources. If you notice that one device tends to sound louder
or softer than other sources in your system, use the 7/3Buttons to
adjust the input level from the source to compensate for the volume
difference without compressing or distorting the signal. This setting
is not the same as the Dolby Volume setting in the Audio Effects
menu, which adjusts for volume differences within the source, e.g.,
television commercial advertisements versus the main program.
See page 33 for information on the Dolby Volume setting.
Audio Auto Polling: Used when both analog and digital
audio connections are made. When no digital signal is present, the
AVR will automatically switch to the analog audio input.
This can be useful for older cable television systems that broadcast
channels in both analog and digital audio.
If an analog audio connection was made, select it here. If not,
choose the Off setting, and the AVR will always use the digital audio
connection.
Zone 2 Audio: Determines the audio source for the multizone
system remote zone. Select the analog audio input the source is
connected to. Digital audio is not available to the multizone system.
Zone 2 Video: Determines the video source for the multizone
system remote zone. Select the composite video input the source is
connected to. Only composite video sources are available to the
multizone system.
Trigger 2: Determines whether a signal will be present at the
Trigger 2 Output when this source is selected.
Record Out: Determines the signal available at the analog
audio outputs.
• Analog: Passes through the analog audio signal selected as
the source input.
• DSP Downmix: When a multichannel audio source is selected
as the input, the AVR creates a 2-channel “LtRt” analog downmix
of the signal.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Now that you have installed your components and completed a
basic configuration, you are ready to begin enjoying your home
theater system.
or while listening to different tracks on a USB drive. The Modeler
module endeavors to re-create the reference presentation that
was heard in the recording studio without losing portions of the
program at the typically lower volume levels often used in the
home. When the Modeler module is active, you may notice details
of the performance that were hidden when the program was played
on other equipment.
TURNING ON THE AVR 7550HD
Flip down the Front-Panel Door and press the Main Power Switch
in. The Power Indicator on the front panel will turn amber, indicating
that the AVR is in Standby mode and is ready to be turned on. The
Main Power Switch is normally left on.
NOTE: The Dolby Volume processor is not used to level
volume across sources. If one source sounds significantly
louder or softer than the others, compensate by adjusting the
Input level from source setting in the Info Settings menu for
the source.
There are several ways to turn on the AVR 7550HD:
a) Press the Standby/On Switch on the front panel.
b) Using the remote, press the AVR Power On Button or any of the
Source Selectors.
To adjust the Dolby Volume setting, press the Audio Effects Button.
A screen similar to the one shown in Figure 24 will appear. Move
the cursor to highlight the Dolby Volume setting, and each press of
the OK Button will switch to one of the options in Table 3 below. The
settings do not refer to the volume level, which is adjusted normally
using the Volume Control, but rather to the amount of Dolby Volume
processing desired. See Figure 24.
To turn the receiver off, press either the Standby/On Switch on the
front panel or the AVR Power Off Button on the remote. Unless the
receiver will not be used for an extended period of time, leave the
Main Power Switch on. When the Main Power Switch is turned off,
any settings you have programmed will be preserved for up to four
weeks.
IMPORTANT NOTE: If the PROTECT message ever
appears in the Message Display, turn off the AVR and unplug
it. Check all speaker wires for a short. If none is found, bring
the unit to an authorized Harman Kardon service center for
inspection and repair before using it again.
VOLUME CONTROL
Adjust the volume either by turning the knob on the front panel
(clockwise to increase volume or counterclockwise to decrease
volume), or by pressing the Volume Control on the remote. The
volume is displayed as a negative number of decibels (dB) below
the 0dB reference point.
Figure 24 – Adjust Dolby Volume
Table 3 – Dolby Volume Settings
Setting
Off
Effect
0dB is the maximum recommended volume for the AVR 7550HD.
Although it’s possible to turn the volume to a higher level, doing
so may damage your hearing and your speakers. For certain more
dynamic audio materials, even 0dB may be too high, allowing for
damage to equipment. Use caution with regard to volume levels.
No Dolby Volume processing
Only Dolby Volume Modeler module is active
Low
Medium
Both Modeler and Leveler modules are active;
Leveler module has a value of 3
To change the volume level display from the default decibel scale
to a 0-to-90 scale, adjust the Volume Units setting in the System
Settings menu, as described on page 48.
Max
Both Modeler and Leveler modules are active;
Leveler module has a value of 9
NOTE: Dolby Volume is compatible with sources recorded
at a sampling rate of 48kHz. High-resolution sources, such as
DTS 96/24, will be decoded at 48kHz. DTS 96/24 programs
will be played in DTS 5.1 mode. To hear DTS 96/24 materials
in high resolution, turn off Dolby Volume.
Dolby Volume
The AVR 7550HD is one of the first products to implement Dolby
Volume processing, which can improve the audio performance of the
system by revealing subtle details even at normal home-listening
volumes.
Dolby Volume Calibration Offset
One concern of the typical home theater listener is that volumes
can vary widely for different programs played by a source, e.g.,
television commercial advertisements are often much louder than
the main feature. Another is that details heard in the recording
studio at typically high reference volumes are lost at the lower
volumes used by many listeners.
Calibration Offset is a feature of Dolby Volume that allows you to
adjust the calibration of the AVR 7550HD to optimally match your
speakers and listening environment. The AVR 7550HD is calibrated
with the average speaker sensitivity in mind; however, different
speakers may have different sensitivities. Use Calibration Offset to
adjust the calibration of the AVR 7550HD according to the types of
speakers you have.
The AVR 7550HD uses two Dolby Volume techniques to address
these issues. The Leveler module maintains a consistent listening
volume within a source, e.g., while watching commercial television
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The average home audio speaker sensitivity is 88dB SPL (8 ohms,
1 watt, 1 meter). Check the sensitivity specification for your loud-
speakers, found in the owner’s manual or on the manufacturer’s
Web site. If your speakers have a sensitivity rating greater than
88dB SPL, increase Calibration Offset by the difference between
your speakers’ sensitivity and 88dB. If they have a sensitivity rating
of less than 88dB SPL, decrease Calibration Offset by the difference
between your speakers’ sensitivity and 88dB.
emulates a 5.1-channel speaker system. No other surround modes
are available for the headphones.
SOURCE SELECTION
Press the front-panel Source List Button. Use the 1/5Buttons
to scroll through the sources. Using the on-screen menus, press
the AVR Settings Button, highlight “Source Select” and press the
OK Button. Scroll to the desired source in the slide-in menu and
press the OK Button.
To adjust the Calibration Offset, press the AVR Settings Button and
scroll to the System Setup menu, then select it. Scroll to the Dolby
Volume Calibration line, which defaults to 0dB. Use the 7/3Buttons
to adjust the setting within the range of –10dB to +10dB.
For direct access to any source, press its Source Selector on
the remote. To directly select Source A, B, C or D, first press the
AVR Settings Button, then press the appropriate Soft Key: red for
Source A, green for Source B, yellow for Source C or blue for
Source D. When using the Zone 2 remote, make sure to connect
the Zone 2 Video Output to a display in the remote zone, and
select these sources using the on-screen menu system.
MUTE FUNCTION
To temporarily mute all speakers and the headphones, press the
Mute Button on the remote. Any recording in progress will not
be affected. The MUTE message will appear in the display as a
reminder. To restore normal audio, press the Mute Button again,
or adjust the volume. Turning off the AVR will also end muting.
The AVR selects the audio and video inputs assigned to the source,
and any other settings made during setup.
The source name, the audio and video inputs assigned to the
source, and the surround mode will appear on the front panel.
The source name and surround mode will also appear on screen.
SLEEP TIMER
The sleep timer sets the AVR to play for up to 90 minutes and then
turn off automatically.
VIDEO TROUBLESHOOTING TIPS:
If there is no picture:
Press the Sleep Settings Button on the remote, and the time
until turn-off will be displayed. Each additional press of the Sleep
Button decreases the play time by 10 minutes, with a maximum
of 90 minutes. The SLEEP OFF setting disables the sleep timer.
• Check the source selection and video input assignment.
• Check the wires for a loose or incorrect connection.
• Check the video input selection on the display device (TV).
When the sleep timer has been set, the front-panel display will
automatically dim to half-brightness and the Volume Control will
go dark.
• Press the front-panel Resolution Button and use the
1/5Buttons until the correct video output resolution is
selected and a picture appears. The CANCEL message will
appear. Press the 5Button to view the ACCEPT option, then
press the OK Button.
If you press the Sleep Button after the timer has been set, the
remaining play time will be displayed. Press the Sleep Button again
to change the play time.
Additional Tips for HDMI Connections:
• Turn off all devices (including the TV, AVR and any source
components).
AUDIO EFFECTS
Adjust the Dolby Volume setting, tone controls, LFE trim or equal-
ization, or select a speaker configuration to improve performance.
Access these settings from the Audio Effects submenu, as described
in the Advanced Functions section.
• Unplug the HDMI cables, starting with the cable between
the TV and AVR, and continuing with the cables between
the AVR and each source device.
It is recommended that you leave the settings at their default values
until you are more familiar with your system.
• Carefully reconnect the cables from the source devices to
the AVR. Connect the cable from the AVR to the TV last.
• Turn on the devices in this order: TV, AVR, source devices.
VIDEO MODES
The settings in the Video Modes menu are used to fine-tune the
picture, if necessary, after making all adjustments on the video dis-
play. It is recommended that you leave the settings at their defaults.
See the Advanced Functions section for detailed information.
USING THE TUNER
To select the AVR 7550HD’s built-in tuner:
1. Press the Source List Button on the front panel. Use the 1/5Buttons
to scroll to the desired tuner band.
HEADPHONES
2. Press the Radio Source Selector on the remote. Press it again
to switch bands (AM, FM or XM).
Plug the 1/4"-inch plug on a pair of headphones into the jack
behind the front-panel door for private listening. The default
Dolby Headphone bypass mode delivers a conventional 2-channel
signal to the headphones.
A screen similar to the one shown in Figure 25 will appear.
The XM band uses a different screen.
Press the Surround Modes Button on the front panel or the remote,
to switch to Dolby Headphone virtual surround processing, which
34
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
To subscribe to XM, U.S. customers should visit xmradio.com or
call 1-800-XMRADIO (1-800-967-2346); Canadian customers
should visit xmradio.ca or call XM Listener Care at 1-877-GETXMSR
(1-877-438-9677).
The AVR 7550HD is an XM Ready device, and is able to receive the
XM service when a user-supplied XM antenna module is connected
and the service activated.
Select an antenna module designated for XM Ready audio components.
An XM Ready module uses the special connector on the AVR and is
controlled by the AVR’s tuner, including its 40 preset station locations
and remote control. Although you may use a “car and home” module
with standard audio connections, you will not be able to enjoy the
AVR’s ease of control.
Figure 25 – FM Radio
Use the 1/5 Buttons or the Channel Control to tune a station
(or channel for XM Radio), as displayed on the front panel and on
screen.
The XM Mini-Tuner and Home Dock (Models CNP-2000 and
CNP-2000H; both pieces are required) are compatible with the
AVR 7550HD. The older Audiovox® CNP 1000 “Connect-and-Play”
module for home audio use is also compatible, but has been dis-
continued. Other modules that have standard analog or digital audio
outputs may be connected to a compatible input and operated
using their own controls.
The AVR defaults to automatic tuning, meaning each press of the
1/5 Buttons scans through all frequencies until a station with
acceptable signal strength is found. To switch to manual tuning,
in which each press of the 1/5 Buttons steps through a single
frequency increment (0.1MHz for FM, or 10kHz for AM), press the
Menu Button. The Mode line will display the current setting. Each
press of the OK Button toggles between automatic and manual
tuning modes.
Plug the module into the XM Antenna Jack on the rear of the
AVR 7550HD. Place the antenna module so that it has a clear view
through a south-facing window.
When an FM station has been tuned, toggling the tuning mode also
switches between stereo and monaural play, which may improve
reception of weaker stations.
Select XM Radio as the source in one of these ways:
1. Press the Source List Button on the front panel. Use the
1/5Buttons to scroll to “XM Radio” and press the OK Button.
A total of 30 stations (AM and FM together) may be stored as presets.
When the desired station has been tuned, press the OK Button, and
two dashes will flash in the front-panel display. Use the Alphanumeric
Keys to enter the desired preset number.
2. Press the Radio Source Selector on the remote repeatedly until
XM Radio is selected.
To tune a preset station, press the 7/3Buttons or the I‹‹ ››I
/
There are four ways to tune an XM Radio channel:
Transport Controls, or press the Menu Button and scroll to the
desired preset, then press the OK Button; or enter the preset number
using the Numeric Keys. For presets 10 through 30, press 0 before
the preset number. For example, to enter preset 21, press 0-2-1.
1. Use the 1/5 Buttons or the Channel Control to scan through
the channel numbers.
2. Use the 7/3Buttons to scan through any previously programmed
preset stations.
XM RADIO OPERATION
3. After you have programmed presets, directly enter the preset
number (1 through 40) using the Alphanumeric Keys. For two-digit
positions, enter a “0” before the number.
To listen to Satellite Radio, you’ll need to connect an XM Satellite
Radio tuner (sold separately) to your XM Ready receiver. XM Satellite
Radio is available to residents of the U.S. (except Alaska and Hawaii)
and Canada.
4. Press the Menu Button to search for a channel by: preset, category,
all channels or direct entry.
Satellite Radio delivers a variety of commercial-free music from
categories including Pop, Rock, Country, R&B, Dance, Jazz, Classical
and many more, plus coverage of all the top professional and college
sports, including play-by-play games from select leagues and teams.
Additional programming includes expert sports talk, uncensored
entertainment, comedy, family programming, local traffic and weather,
and news from your most trusted sources.
When you are able to hear Channel 1, you are ready to activate your
module. If you don’t hear Channel 1, make sure the module’s plug
is firmly seated in the XM Antenna jack, and that the module is near
a south-facing window. Try unfolding the module and rotating it to
obtain reception. You may need to purchase an extension cable to
ensure that the module is near the window.
Tune to Channel 0 for a display of your module’s Radio ID number.
You may also view the Radio ID number by pressing the Menu Button
and selecting “XM Setting”.
Once you’ve purchased an XM tuner, you’ll need to activate and
subscribe to begin enjoying the service. Easy-to-follow installation
and setup instructions are provided with the satellite tuners. There
are a variety of programming packages available, including the option
of adding “The Best of SIRIUS” programming. (“The Best of SIRIUS”
service is not available to XM Canada subscribers at this time.)
The current channel number and preset location will appear in
the upper line of the Message Display, and the channel name will
appear in the lower line. Three signal-strength bars will appear to
the right of the channel number and preset location. The song title,
artist and channel category, along with the channel number and
preset position (if programmed), will all appear on screen when
a video display is in use.
Family-friendly packages are also available to restrict channels
featuring content that may be inappropriate for children.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
For traffic and weather channels, the current city’s name will
appear instead of the channel name, and the local weather and
temperature will be displayed on screen.
• To view the still images in random order, press the Menu Button
and select the Random Photos setting. Each press of the OK
Button turns the setting on or off.
• To view a slideshow of images, select a folder containing the
images for playback. You may also select audio files stored
on the same device for playback as background music to the
slideshow. Select the audio file, then the image files.
To store a channel in one of the 40 preset locations:
1. Tune to the desired channel and press the OK Button. Two dashes
will flash.
2. Use the Alphanumeric Keys to enter the numbered preset loca-
tion you wish to store the channel in. For two-digit numbers,
enter a “0” before the number.
• When both music and a slideshow are playing, if the slide-in
menu is not displayed, press the 7/3Buttons to skip to the
next picture or return to the previous picture. When the slide-in
menu is displayed, press the 7/3Buttons to skip to the next
or previous audio track.
3. After you have programmed presets, directly enter the preset
number (1 through 40) using the Alphanumeric Keys. For two-
digit positions, enter a “0” before the number.
• While an image is being displayed, each press of the 1Button
rotates the image 90º clockwise, and each press of the 5Button
rotates the image 90º counterclockwise.
USB PLAYBACK
To enjoy audio and still-image playback of media stored on a USB
flash drive, connect the drive to the front-panel USB Port and select
the USB source on the AVR. Press the Menu Button and select
“Browse USB”. The AVR will list the folders and files of audio and
still-image content. Do not connect a personal computer or peripheral
to the USB Port. USB hubs and multi-card readers are not supported.
• To change the duration of each image on screen during a
slideshow, press the Menu Button and select the Slideshow
Speed setting. Each press of the OK Button changes the speed:
Slow, Medium or Fast.
INTERNET RADIO
IMPORTANT NOTE: The AVR 7550HD’s internal processor
requires about 10 seconds to detect, recognize and connect
to a USB device. Please wait 10 seconds after inserting a device
or switching the USB source before attempting to browse the
device. If you try to browse the device sooner, the AVR may
not display the device’s contents correctly in the on-screen
slide-in menu. If that happens, remove the device and reinsert
it into the USB Port, then wait 10 seconds before browsing.
Always stop playback before removing a USB drive, and wait
at least 10 seconds before inserting another drive.
With its network connection, the AVR 7550HD opens a world of
MP3- and WMA-format streams when Internet access is available.
Connect the RJ-45 Network jack on the AVR to an Ethernet port on
a home-network router. Turn on the AVR and the video display, and
press the Network Selector on the remote. Each press toggles
between the Network Now Playing and Internet Radio screens.
With the Internet Radio screen displayed, the AVR will automati-
portal. To select a stream, press the Menu Button, and use the
1/5Buttons to search by category: Presets, Favourites, Location,
Genre, New Stations, Most Popular or Podcasts.
• To expand a folder, press the OK Button or the 3Navigation Button.
from your PC. Enter the ID # of your AVR 7550HD (found by pressing
the Menu Button and selecting “Network Setup”) and create an
account. Favourites that you select on the Web site will be available
on the AVR.
• To collapse a folder or return to the previous menu level, press
the Back/Exit Button or the 7 Button.
• To play all audio or still-image files within a folder, select the
folder and press the OK Button or the Play Button.
• To skip to the next track or image, press the 3Navigation Button.
Navigation is similar to other slide-in menus. Scroll to the desired
item and press the OK Button or the 3 Button to select it. To return
to the previous menu level (or to clear the menu from view from the
top level), press the Back/Exit Button or the 7 Button.
• To return to the beginning of the current track, press the
7 Button once; to return to the previous track, press the
7 Button twice. When displaying images, pressing the
7 Button returns to the previous image.
If you know the URL (Uniform Resource Locator, or Web address)
of a specific audio stream, select the Direct Station option from
the menu. The AVR 7550HD is not able to connect to streams that
require site registration or other interaction prior to playing the
stream. A live stream is required. If the AVR cannot connect to the
stream, the “Station Not Live” message will appear briefly, and the
Internet Radio screen will remain essentially blank. Not all URLs
will be accessible.
• The Transport Controls may be used to control playback for
skipping to the previous or next track, searching at high speed
forward or backward within a track, playing a file, pausing
playback or stopping playback.
• To repeat a file or folder, press the Menu Button and select the
Repeat option. Each press of the OK Button will change the
setting from Off (no repeat) to Repeat One (file) to Repeat All
(files at the current directory level of the drive). Repeat All will
always be activated when Random Music playback is turned on.
Up to 30 preset Internet Radio stations may be programmed. To
set a preset, first tune the station. Press the OK Button, and two
dashes will flash. Enter the preset number using the Alphanumeric
Keys. The connection to the station will momentarily stop, interrupt-
ing the program, and the AVR will reconnect to the station.
• To play the audio tracks in random order, press the Menu
Button and select the Random Music setting. Each press of the
OK Button turns the setting on or off. The AVR will automatically
repeat the tracks until playback is stopped manually.
To connect to a station programmed as a preset, enter its preset
number using the Alphanumeric Keys, or select from the previously
programmed presets using the 7/3 Buttons.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
NOTES ON NETWORK SETUP:
• Although video content may appear in the menu, the AVR
does not support video playback from the network connection.
• It is recommended that the AVR be connected to a home-network
router so that it can directly access the Internet for Internet
Radio, or access a PC on the network for playback of content
stored on the PC (see the Network Playback section below).
RECORDING
Two-channel analog and digital audio signals, as well as composite
and S-video signals, are normally available at the appropriate
recording outputs. To make a recording, connect your audio or
video recorder to the appropriate output jacks, as described in the
Installation section, insert blank media and make sure the recorder
is turned on and recording while the source is playing.
• If you are unable to connect to the Internet, try adjusting the
network settings. Press the Menu Button and select Network
Setup. The Network Settings line will be highlighted. Each
press of the OK Button toggles between Manual and Automatic
network setup. Select Manual, and the other network settings
will be displayed: IP Address, Subnet Mask, Gateway, Primary
DNS, Secondary DNS, Proxy Address and Proxy Port. Contact
your ISP (Internet Service Provider) for the correct information
to enter into these settings. To change a setting, highlight it
and press the OK Button. Use the 7/3 Buttons to move the
cursor from one position to the next, and scroll to the desired
number using the 1/5Buttons. Press the OK Button when
you are finished with an entry. Scroll down to the “Apply and
Save” Button and select it. The AVR will turn off and must be
powered back on. To return to the previous menu screen,
press the Back/Exit Button.
NOTES:
1. Analog and digital audio signals are not converted to the
other format.
2. Only PCM digital audio signals are available for recording.
Proprietary formats such as Dolby Digital and DTS may not
be recorded using the digital audio connections. Use the
analog audio connections to make an analog recording.
3. HDMI and component video sources are not available for
recording.
4. Please make certain that you are aware of any copyright
restrictions on any material you record. Unauthorized dupli-
cation of copyrighted materials is prohibited by federal law.
NETWORK PLAYBACK
The AVR 7550HD is capable of playing audio media stored on
a PC when both the PC and the AVR are connected to a home-
network router.
USING
DOCKING STATION
The Bridge II is an included dock that is compatible with most
docking iPod models, 4G and later (not included). When The Bridge II
is connected to its proprietary input on the AVR 7550HD and the
iPod is docked, you may play the audio, video and still-image
materials on your iPod through your high-quality audio/video system,
operate the iPod using the AVR remote or the AVR’s front-panel
controls, view navigation messages on the AVR’s front panel or
a connected video display, and charge the iPod.
NOTES:
• The PC must be running Windows Media® Player version 11 or
higher, Windows Media Center version 2.0 or 3.0, or Intel®
Media Server. It is recommended that any firewalls be
turned off, although Windows Media Player may automati-
cally make any necessary adjustments to the firewall settings
to allow media sharing.
When the source The Bridge is selected and an iPod is docked,
the message “The Bridge” appears in the front-panel Message
Display. If the AVR doesn’t detect the iPod, turn off the AVR, remove
the iPod from The Bridge II and reset the iPod. When the iPod
returns to its main menu, redock it and turn on the AVR.
• An Apple Macintosh computer must be running DLNA
(Digital Living Network Alliance)-compliant software.
Examples of compatible software include the MediaLink
program by Nullriver, Inc., and EyeConnect™ software by
Elgato Systems.
Table 4 summarizes the controls available with The Bridge II during
normal playback.
From the media player software, select the “Share media” option
(or a similar menu option), and select the AVR as the device.
Table 4 – Using The Bridge II
On the AVR, select Network as the source. Press the Network
Source Selector a second time, if necessary, to switch from the
Internet Radio source to the Network source. Press the Menu
Button, and the PC should appear by name.
iPod Function
Play
Pause
Menu
Back/Exit
Select
Scroll Reverse
Scroll Forward
Forward Search
Reverse Search
Next Track
Previous Track
Page Up/Down
Remote Control Key
Play (
Pause (II)
Menu
Back/Exit or Left Arrow 7
(
OK or Right Arrow 3
)
3
Browse the content stored in the PC’s media player library, using the
slide-in menu. Scroll to the desired item and press the OK Button or
the 3 Navigation Button to select it. To return to the previous menu
level (or to clear the menu from view from the top level), press the
Back/Exit Button or the 7 Button.
(
)
)
( )
Up Arrow 1
( )
Down Arrow 5
(
)
)
Forward Search 33
(
Reverse Search 77
NOTES:
(
(
)
Next 33 I) or Right Arrow 3
• The Repeat, Random and Slideshow Speed settings are
global for Network Playback and USB Playback. Changing
these settings for one of these sources will have the same
effect for the other source.
) or Left Arrow (
)
Previous (I77
Page Up/Down
7
I
Stop
Stop ( )
37
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Press the Menu Button to view the slide-in menu:
repeat play has been programmed, an icon will appear in the upper
right corner.
Music: Navigates the audio materials stored on the iPod.
The screen may disappear from view, depending on the Setup and
Slide-In Menus setting in the System Settings menu (described in
the Advanced Functions section). Restore the Now Playing screen
to view by pressing either of the 7/3Buttons.
Photo/Manual: Select this line to view still images stored on
a photo-capable iPod. The system will switch to iPod Manual Mode,
and control will shift to the iPod. Use the screen and controls on the
iPod. The AVR remote may also be used.
NOTE: It is strongly recommended that you use the screen
saver built into your video display to avoid possible damage
from “burn-in” that may occur with plasma and many CRT
displays when a still image, such as a menu screen, remains
on display for an extended period of time.
To view photos on a video monitor connected to the AVR, select the
photo and press the Play Button on the iPod, or press the OK Button
on the remote three times.
Videos: Select this line to view videos stored on an iPod that
supports video browsing.
iPod MANUAL MODE
NOTES ON VIDEO PLAYBACK:
• As of this writing, video browsing is only supported on the
iPod 5G, iPod classic (80GB, 120GB and 160GB), iPod nano
3G and 4G, and iPod touch (when loaded with software
version 2 or higher). For other iPod models, it is not possible
to view photos (except iPod 4G) or videos on an external
monitor while using The Bridge II.
Press the Menu Button and select Photo/Manual to enter iPod
Manual Mode. This is required to view photos stored on the iPod.
Table 5 summarizes the controls available with The Bridge II in iPod
Manual Mode.
Table 5 – Using The Bridge II in iPod Manual Mode
• Before attempting to view photos or videos stored on your
iPod, check the Video Settings menu on the iPod and make
sure that the TV Out setting is set to On. The TV Signal
setting should be NTSC, to match the capabilities of your
video display. If your selection was playing and is paused,
the iPod requires you to reselect the video for the new
TV Out setting to take effect.
iPod Function
Play
Pause
Menu
Select
Select Next Screen (Scrubber, Right Arrow (
Cover Art, Ratings)
Scroll Reverse
Scroll Forward
Next Track
Remote Control Key
Play (
Pause (II)
Back/Exit or Left Arrow (
OK
)
3
)
7
)
3
• If you do not see the Videos line in the menu, and the iPod
supports video browsing and has video content stored on
it, you may need to turn off the AVR, remove the iPod from
The Bridge II, reset the iPod, turn the AVR back on and dock
the iPod again. This procedure may also help when a video
program is selected but the “Now Playing” screen appears
instead of the video images.
Page Up or Up Arrow (1)
Page Down or Down Arrow (
)
5
Next (
Previous (I77
33 I)
Previous Track
)
The AVR supports audio playback from some applications available
To exit iPod Manual Mode, with the AVR remote in The Bridge mode, for the iPod touch. Place the system in iPod Manual Mode by press-
press the Menu Button. To return to a previous menu level on the
iPod, press the Back/Exit Button.
ing the Menu Button and selecting “Photo/Manual”. Then use the
controls on the iPod touch to run the application. Due to the wide
variety of applications and many factors affecting them, playback is
not guaranteed.
Random: Select this setting for random playback, also known as
“Shuffle Mode”. Each press of the OK Button switches the setting:
shuffle by Song, shuffle by Album, or Off to end random playback.
While scrolling, hold the key to scroll faster. Use the Page Up/Down
control on the remote to scroll a page at a time (not in Manual Mode).
Repeat: Select this setting to repeat a track or all tracks in the
current album or playlist. Each press of the OK Button switches
the setting: repeat Off, repeat One or repeat All.
NOTES:
• The Play and Pause functions are not available unless
content has been selected for playback.
NOTE: The iTunes application allows you to exempt some
tracks from Shuffle mode. The AVR 7550HD cannot override
this setting.
• To search within a track (not in Manual Mode), press and
hold the indicated button. Press the Previous Track Button
once to skip to the beginning of the current track. Press the
Previous Track Button twice to skip to the beginning of the
previous track.
While a selection is playing, the song title and play mode icon will
appear in the front-panel Message Display.
If a video monitor is connected to the AVR 7550HD and the system
is not in iPod Manual Mode, the Now Playing screen will appear and
display the play mode icon, song title, artist and album. A graphic
bar indicates the current play position within the track. If random or
When a slideshow is being displayed, some controls have different
effects:
• To pause the slideshow, including any audio track that is playing,
press the Pause Button.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• To resume a paused slideshow, press the Pause Button. Pressing
the Play Button begins audio playback.
• 7 CH STEREO follows the same scheme as 5 CH STEREO, but
adds the surround back speakers. This mode is only available
when the surround back speakers are present and have not
been reassigned to multizone operation. See page 47 for more
information.
• To play an audio track stored on the iPod, adjust the slideshow
settings on the iPod.
• To skip to the next or previous photo on the iPod, press the Next
or Previous Transport Control.
Movie: Use when a surround mode is desired for movie playback:
Logic 7 Movie, DTS Neo:6 Cinema or Dolby Pro Logic II (IIx when
seven main speakers are present).
• It is not possible to skip to the next or previous audio track during
a slideshow.
• To search forward or in reverse within an audio track, press the
Forward or Reverse Search Transport Control. If no audio track is
playing, these controls will have no effect during the slideshow.
Music: Use when a surround mode is desired for music playback:
Logic 7 Music, DTS Neo:6 Music or Dolby Pro Logic II (IIx when
seven main speakers are present). The Dolby Pro Logic II/IIx Music
mode allows access to a submenu with some additional settings.
See the Advanced Functions section for more information.
SELECTING A SURROUND MODE
Surround mode selection can be as simple or sophisticated as
your individual system and tastes. Feel free to experiment, and
you may find a few favorites for certain sources or program types.
More detailed information on surround modes may be found in
the Advanced Functions section.
Video Game: Use to select a surround mode for game playback:
Logic 7 Game, or Dolby Pro Logic II (IIx when seven main speakers
are present) Game.
After you have made your selection, press the Back/Exit Button.
See the Advanced Functions section for more information on
surround modes.
To select a surround mode, press the Surround Modes Button
(front panel or remote). The Surround Modes menu will appear
(see Figure 26). Use the 1/5Buttons until the desired surround
mode category appears: Auto Select, Virtual Surround, Stereo,
Movie, Music or Video Game. Press the OK Button to change
the audio type’s surround mode.
Figure 26 – Surround Modes Menu
Auto Select: For digital programs, such as movies recorded
with a Dolby Digital soundtrack, the AVR will automatically use the
native surround format. For 2-channel analog and PCM programs,
the AVR uses Logic 7 Movie, Music or Game mode, depending on
the source.
Virtual Surround: When only two main speakers are present
in the system, Dolby Virtual Surround may be used to create an
enhanced soundfield that virtualizes the missing speakers. Select
between Wide and Reference modes.
Stereo: When 2-channel playback is desired, select the number
of speakers used for playback:
• 2 CH STEREO uses only two speakers. As described on page 40,
you may select Analog Bypass mode for a pure analog signal
when analog audio inputs are in use. Turn off the Tone Control
setting in the Audio Effects submenu, and the AVR does the rest.
• 5 CH STEREO plays the left-channel signal through the front
and surround left speakers, the right-channel signal through the
right speakers and a summed mono signal through the center
speaker.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Much of the AVR 7550HD’s performance is handled automatically,
Digital Audio Signals
with little intervention required on your part. The AVR 7550HD is
capable of being customized to suit your system and your tastes.
In this section, some of the more advanced adjustments available
are described.
Digital audio signals offer greater capacity, which allows the
encoding of center and surround channel information directly
into the signal. The result is improved sound quality and startling
directionality, since each channel is reproduced discretely.
Even when only two channels are encoded, the digital signal
allows for a higher sampling rate that delivers greater detail.
High-resolution recordings sound extraordinarily distortion-free,
especially at high frequencies.
AUDIO PROCESSING AND SURROUND
SOUND
Audio signals output by sources are encoded in a variety of formats
that can affect not only the quality of the sound but the number of
speaker channels and the surround mode. You may also manually
select a different surround mode, when available.
Surround Modes
Surround mode selection is dependent upon the format of the
incoming audio signal, as well as personal taste. Table A13 offers a
brief description of each mode and indicates the types of incoming
signals or digital bitstreams the mode may be used with. Additional
information about the Dolby and DTS modes is available on the
Analog Audio Signals
Analog audio signals usually consist of two channels – left and
right. The AVR 7550HD offers three options for playback:
1. Analog Bypass Mode: The 2-channel signal is passed
directly from the input to the volume control, without being
digitized or undergoing any processing for bass management
or surround sound. To select analog bypass mode:
When in doubt, check the jacket of your disc for more information
on which surround modes are available. Usually, nonessential
sections of the disc, such as trailers, extra materials or the disc
menu, are only available in Dolby Digital 2.0 (2-channel) or PCM
2-channel mode. If the main title is playing and the display shows
one of these surround modes, look for an audio or language setup
section in the disc’s menu. Also, make sure your player’s audio
output is set to the original bitstream rather than 2-channel PCM.
Stop play and check the player’s output setting.
a) The analog audio inputs for the source must be selected. If
necessary, press the Info Button on the remote and use the
1/5Buttons to scroll to the Audio Input from source setting.
b) The tone controls must be disabled by setting the Tone Control
to Off. Press the Audio Effects Button to access the Tone
Control setting.
For any incoming signal, only a limited number of surround
modes are available. Although there is never a time when all of
the AVR 7550HD’s surround modes are available, there is usually
a wide variety of modes available for a given input.
c) The 2-channel Stereo mode must be selected. Press the
Surround Modes Button to access the STEREO line of the
Surround Modes submenu. Press the OK Button to select
2-channel Stereo.
Multichannel digital recordings are found in the 5.1-, 6.1- or 7.1-
channel formats. The channels included in a 5.1-channel recording
are front left, front right, center, surround left, surround right and
LFE. The LFE channel is denoted as “.1” to represent the fact that
it is limited to the low frequencies.
When the Tone Control setting is Off, the front speakers will
be set to Large automatically. When the Tone Control setting
is turned On, if you have set the front speaker crossover to
a numeric setting, the front speakers will return to the Small
setting.
6.1-Channel recordings add a single surround back channel, and
7.1-channel recordings add surround back left and surround back
right channels to the 5.1-channel configuration. New formats are
available in 7.1-channel configurations. The AVR 7550HD is able to
play the new audio formats, delivering a more exciting home theater
experience.
NOTE: Audio from The Bridge II source is analog, and when
2-channel Stereo mode is selected, the audio will be played in
Analog Bypass mode.
2. DSP Surround Off Mode: The DSP Surround Off mode
digitizes the incoming signal and applies the bass management
settings, including speaker configuration, delay times and output
levels. Select this mode when your front speakers are small,
limited-range satellites and you are using a subwoofer. To select
this mode, use a digital audio input, or turn the Tone Control
setting off, and select 2-channel Stereo mode.
NOTE: To use the 6.1- and 7.1-channel surround modes,
the Surround Back channels must be enabled. See the Manual
Speaker Setup section on page 41 for more information.
The Digital formats are Dolby Digital 2.0 (two channels only), Dolby
Digital 5.1, Dolby Digital EX (6.1), Dolby Digital Plus (7.1), Dolby
TrueHD (7.1), DTS-HD High-Resolution Audio (7.1), DTS-HD Master
Audio (7.1), DTS 5.1, DTS-ES (6.1 Matrix and Discrete), DTS 96/24
(5.1), 2-channel PCM modes in 32kHz, 44.1kHz, 48kHz or 96kHz,
and 5.1 or 7.1 multichannel PCM.
3. Analog Surround Modes: The AVR 7550HD is able to
process 2-channel audio signals to produce multichannel sur-
round sound, even when no surround sound has been encoded
in the recording. Among the available modes are the Dolby
Pro Logic II/IIx modes, the Dolby Virtual Speaker modes, the
DTS Neo:6 modes, the Logic 7 modes and the Stereo modes.
When a digital signal is received, the AVR 7550HD detects the
encoding method and the number of channels, which is displayed
briefly as three numbers, separated by slashes (e.g., “3/2/.1”).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
The first number indicates the number of front channels in the signal:
You may select a different mode. The choice of surround modes
depends on the number of speakers in your system.
“1” represents a monophonic recording, usually an older program
that has been digitally remastered or, more rarely, a modern
program for which the director has chosen a special effect.
• Virtual Surround: Dolby Virtual Speaker Reference or Wide
• Stereo: 2-channel stereo, 5-channel stereo or 7-channel stereo
“2” indicates the presence of the left and right channels, but no
center channel.
• Movie: Logic 7 Movie, DTS Neo:6 Cinema, Dolby Pro Logic II
Movie, Dolby Pro Logic IIx Movie
“3” indicates that all three front channels (left, right and center)
are present.
• Music: Logic 7 Music, DTS Neo:6 Music, Dolby Pro Logic II
Music, Dolby Pro Logic IIx Music
The second number indicates whether any surround channels are
present:
• Video Game: Logic 7 Game, Dolby Pro Logic II Game, Dolby
Pro Logic IIx Game
“0” indicates that no surround information is present.
“1” indicates that a matrixed surround signal is present.
“2” indicates discrete left and right surround channels.
Once you have programmed the surround mode for each type of
audio, select the line from the Surround Modes menu to override
the AVR’s automatic surround mode selection. The AVR will use the
same surround mode the next time the source is selected.
“3” is used with DTS-ES bitstreams to represent the presence
of the discrete surround back channel, in addition to the side
surround left and right channels.
Please refer to Table A13 in the appendix for more information on
which surround modes are available with different bitstreams.
“4” is used with 7.1-channel digital formats to indicate the presence
of two discrete side surround channels and two discrete back
surround channels.
Dolby Surround Settings
Some additional settings are available for Dolby modes. When the
Dolby Pro Logic II or IIx Music modes have been selected, choose
the Edit submenu to adjust the Center Width, Dimension and
Panorama settings. See Figure 27.
The third number is used for the LFE channel:
“0” indicates no LFE channel.
“.1” indicates that an LFE channel is present.
The 6.1-channel signals – Dolby Digital EX and DTS-ES Matrix
and Discrete – each include a flag meant to signal the receiver to
decode the surround back channel, indicated as 3/2/.1 EX-ON for
Dolby Digital EX materials, and 3/3/.1 ES-ON for DTS-ES materials.
Dolby Digital 2.0 signals may include a Dolby Surround flag indicating
DS-ON or DS-OFF, depending on whether the 2-channel bitstream
contains only stereo information, or a downmix of a multichannel
program that can be decoded by the AVR’s Dolby Pro Logic decoder.
By default, these signals are played in Dolby Pro Logic IIx Movie mode.
When a PCM signal is received, the PCM message and the sampling
rate (32kHz, 44.1kHz, 48kHz or 96kHz) will appear.
Figure 27 – Dolby Pro Logic II/IIx Music Mode Settings
Center Width: This setting affects how vocals sound through
the three front speakers. A higher number (up to 7) focuses the
vocal information tightly on the center channel. Lower numbers
broaden the vocal soundstage. Use the 7/3Buttons to adjust.
When only two channels – left and right – are present, the analog
surround modes may be used to decode the signal into the remain-
ing channels. If you would prefer a different surround format than
the native signal’s digital encoding, press the Surround Modes
Button to display the Surround Modes menu (see Figure 26).
Dimension: This setting affects the depth of the surround pres-
entation, allowing you to “move” the sound toward the front or rear
of the room. The setting of “0” is a neutral default. Setting “F-3”
moves the sound toward the front of the room, while setting “R-3”
moves the sound toward the rear. Use the 7/3Buttons to adjust.
The Auto Select option uses the native signal’s digital encoding,
e.g., Dolby Digital, DTS, Dolby TrueHD or DTS-HD Master Audio.
For 2-channel materials, the AVR defaults to Logic 7 Movie mode.
If you prefer a different surround mode, select the surround mode
category: Virtual Surround, Stereo, Movie, Music or Video Game.
Press the OK Button to change the mode.
Panorama: With the Panorama mode turned ON, some of the
sound from the front speakers is moved to the surround speakers,
creating an enveloping “wraparound” effect. Each press of the OK
Button toggles the setting on or off.
Each category is set to a default surround mode:
• Virtual Surround: Dolby Virtual Speaker Reference
• Stereo: 7-channel stereo
MANUAL SPEAKER SETUP
The AVR 7550HD is flexible and may be configured for most speakers,
and to compensate for the acoustic characteristics of your room.
• Movie: Logic 7 Movie
• Music: Logic 7 Music
The EzSet/EQ II process automatically detects the capabilities of
each speaker, and optimizes the AVR 7550HD’s performance. If you
• Video Game: Logic 7 Game
41
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
are unable to run EzSet/EQ II calibration, or if you wish to make
further adjustments, use the Manual Speaker Setup on-screen
menus.
STEP THREE – Manual Setup Menu
Now you are ready to program the receiver. Sit in the usual listening
position and make the room as quiet as possible.
Before beginning, place your loudspeakers as explained in the
Speaker Placement section, and connect them to the AVR. Consult
the owner’s guide for the speakers or the manufacturer’s Web site
for the frequency range specification. Although you may set the out-
put levels “by ear,” an SPL (sound-pressure level) meter purchased
at a local electronics store will provide greater accuracy.
With the receiver and video display turned on, press the AVR
Settings Button to display the menu system. Use the 5Button to
move the cursor to the Speaker Setup line, and press the OK Button
to display the Speaker Setup menu. See Figure 21.
If you have run the EzSet/EQ II process, the results were saved
in one of the two listening positions. Adjust the Speaker Setup
setting in the Audio Effects menu to activate the results for either
position (see page 45). To tweak the EzSet/EQ II results, or to con-
figure the AVR from scratch, select Setup Listening Position 1 or
Setup Listening Position 2. A screen similar to the one shown in
Figure 28 will appear.
Record your configuration settings in Tables A3 through A12 in the
appendix for easy re-entry after a system reset, or if the AVR’s
Master Power Switch is turned off or the unit is unplugged for
more than four weeks.
NOTE: When using the AVR’s Speaker Setup menus, select
a video output resolution of 720p or higher to view graphics
that simplify configuration.
STEP ONE – Determine Speaker
Crossover
Without using the EzSet/EQ II process, the AVR 7550HD can’t detect
how many speakers you’ve connected to it; nor can it determine
their capabilities. Consult the speaker’s technical specifications
and locate the frequency response, usually given as a range, e.g.,
100Hz – 20kHz ( 3dB). Write down the lowest frequency that each
of your main speakers is capable of playing (100Hz in the example)
as the crossover in Table A3 in the appendix. This is not the same
as the crossover frequency listed in the speaker’s specifications.
For the subwoofer, write down the transducer size.
Figure 28 – Speaker Setup Position Menu
NOTE: All of the speaker setup submenus include the Back
option, as shown at the bottom of Figure 28. To save the current
settings, select the Back option.
The receiver’s bass management determines which speakers will
be used to play back the low-frequency (bass) portion of the source
program. Sending the lowest notes to small satellite speakers won’t
sound right, and may even damage the speaker. The highest notes
may not be heard at all through the subwoofer.
To reconfigure the speakers from scratch, select the Reset option.
For best results, adjust the submenus in this order: Number of
Speakers, Crossover (Size), Sub Mode, Distance and Level Adjust.
Number of Speakers
With proper bass management, the AVR 7550HD divides the source
signal at a crossover point. All information above the crossover
point is played through the satellite speaker, and all information
below the crossover point is played through the subwoofer. Each
loudspeaker in your system performs at its best, delivering an
enjoyable sound experience.
Move the cursor to the Number of Speakers line and press the
OK Button. See Figure 29.
STEP TWO – Measure Speaker Distances
Ideally, all of your speakers would be placed in a circle, with the
listening position at the center. However, you may have had to place
some speakers a little further away from the listening position than
others. Sounds that are supposed to arrive simultaneously from
different speakers may blur, due to different arrival times.
Figure 29 – Number of Speakers Menu
Use the AVR’s delay adjustment to compensate for real-world
speaker placements.
Program the correct setting for each speaker group: ON when the
speakers are present in the system, and OFF for positions where no
speakers are installed. The Front Left & Right speakers are always
ON and may not be disabled. Any changes will be reflected in the
total number of speakers displayed at the top of the screen.
Measure the distance from each speaker to the listening position,
and write it down in Table A4 in the appendix. Even if all of your
speakers are the same distance from the listening position, enter
your speaker distances as described in Step Three.
The setting for the surround back speakers includes a third option:
Zone 2. The AVR 7550HD is capable of multizone operation, supporting
placement of a pair of speakers in another room. The AVR 7550HD’s
assignable surround back amplifier channels make multizone operation
42
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
easier than ever, since an external power amplifier is not required.
have a subwoofer, either upgrade to full-range speakers or add
a subwoofer at the earliest opportunity.
Select the Zone 2 option at this line, and connect the Surround
Back Speaker Outputs to loudspeakers located in the remote room.
The main room will be configured automatically for up to 5.1 channels.
See the Multizone Operation section for more information.
• If you set the front speakers to LARGE, select one of the three
settings for the subwoofer.
N
L/R+LFE: This setting sends all low-frequency information
NOTE: When the Surround Back speakers are set to “Zone 2”,
they will not be configured during the EzSet/EQ II process. To
use the speakers in the main listening area, configure them as
“On”, and run the EzSet/EQ II process for a 7.1- or 7.2-channel
system. If the speakers will only be used during multizone
operation, configure them manually, as explained below.
to the subwoofer, including both information that would nor-
mally be played through the front left and right speakers, and
the special low-frequency effects (LFE) channel information.
N
Off: Select this setting when no subwoofer is in use. All
low-frequency information will be sent to the front left and
right speakers.
N
The settings in this menu affect the remainder of the speaker setup
process and the availability of various surround modes at any time.
LFE: This setting plays low-frequency information contained
in the left and right program channels through the front
speakers, and directs only the LFE channel to the subwoofer.
When you have finished, select the Back option or use the
Back/Exit Button.
NOTE: If you are using a Harman Kardon HKTS Series
speaker system, select the appropriate numeric crossover fre-
quency for the Main Speaker groups, and the subwoofer will
automatically be set to LFE.
Adjust Crossover Frequencies Menu
After you have programmed the number of speakers, the AVR will
return to the Speaker Setup Position menu (see Figure 28). Navigate
to the Crossover (Size) line and press the OK Button to display the
Adjust Crossover Frequencies menu (see Figure 30).
Adjust Speaker Distance Menu
Placing the speakers at different distances from the listening positions
can muddy the sound, as sounds are heard earlier or later than desired.
Even if all of your speakers are placed the same distance from the
listening position, do not skip this menu.
On the Speaker Setup Position menu, move the cursor to the
Distance line and press the OK Button to display the Adjust Speaker
Distance menu. See Figure 31.
Figure 30 – Adjust Crossover Frequencies Menu
The AVR will only display those speaker groups programmed in the
Number of Speakers menu.
Refer to Table A3 for each speaker’s crossover. For the main speakers,
this is the lowest frequency the speaker reproduces well.
For each main speaker, select one of the seven crossover frequencies:
40Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the crossover
frequency is below 40Hz, select the first option, “Large”. This setting
doesn’t refer to the speaker’s physical size, but to its frequency
response, which is also called “full range”.
Figure 31 – Adjust Speaker Distance Menu
Enter the distance from each speaker to the listening position, as
measured in Step Two – Measure Speaker Distances and recorded
in Table A4 in the appendix (see page 42).
Specify the size of the subwoofer’s transducer as 8, 10, 12 or 15
inches. The AVR always sets the subwoofer crossover to 100Hz, but
uses the transducer size for equalization. Write down the settings
in Table A3 in the appendix.
The default unit of measurement is feet. To change the unit to
meters, return to the main AVR menu. Select the System Settings
menu, then scroll down to the General AVR Settings section and
select the Unit of Measure line. Press the OK Button to change
the setting.
When you have finished entering the settings, select Back, or press
the Back/Exit Button.
Select a speaker, then use the 7/3Buttons to change the meas-
urement. The values vary between 0 and 30 feet, with a default
of 12 feet for all speakers except the Surround Left and Right
Speakers, for which the default is 10 feet.
Sub Mode
Move the cursor to the Sub Mode line. This setting depends upon
how you programmed the front left and right speakers.
NOTE: If the surround back channels are assigned to the
multizone system, you will not be able to adjust their delay
settings.
• If you set the front speakers to a numeric crossover frequency,
the subwoofer setting will always be LFE. All low-frequency
information will always be sent to the subwoofer. If you don’t
43
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
When this setting reads AUTO, the test tone will automatically
STEP FOUR – Setting Channel Output
Levels Manually
For a conventional 2-channel receiver, the balance control affects
the stereo imaging by adjusting the relative loudness of the left and
right channels.
circulate to all channels, pausing for a few moments at each channel
and then moving to the next channel several seconds later, as
indicated by the highlight bar. Adjust the level for any channel
when the test tone is paused there, using the 7/3Buttons. Use
the 1/5Buttons to move the cursor to another line, and the test
tone will follow the cursor.
With up to seven main channels, plus a subwoofer, imaging
becomes both more critical and more complex. The goal is to
ensure that each channel is heard at the listening position with
equal loudness.
When this setting reads MANUAL, the test tone will not move to the
next channel until you use the 1/5Buttons.
Individual Channels: If you are using an external source
to set your output levels, navigate to each channel and use the
7/3Buttons to adjust the level, as desired, between –10dB
and +10dB.
EzSet/EQ II calibration can handle this critical task for you, simply
and automatically. However, the AVR’s Adjust Speaker Levels menu
allows you to calibrate the levels manually, either using the system’s
test tone or while playing source material.
When you have finished adjusting the speaker levels, select the
Back option or press the Back/Exit Button. Record the level settings
in Table A3 in the appendix.
1. Make sure all speakers have been placed and connected correctly.
2. Adjust the number of speakers, crossover, distance and sub mode
for each speaker in your system, as described in Step Three.
AUDIO EFFECTS
3. Measure the channel levels in one of these ways, and adjust the
channel levels using the Adjust Speaker Levels menu:
To adjust other audio settings, such as the tone controls, to improve
performance, press the Audio Effects Button to display the Audio
Effects menu (see Figure 24). The menu may also be accessed from
the Setup Source menu by pressing the Info Settings Button and
selecting Audio Effects.
a) Preferably, use a handheld SPL meter set to the C-Weighting,
Slow scale. Adjust each channel so that the meter reads 75dB.
b) By ear. Adjust the levels so that all channels sound equally loud.
c) If you are using a handheld SPL meter with source material,
such as a test disc or an audio selection, play it and adjust the
AVR’s master volume control until the meter measures 75dB.
NOTE: The settings in the Audio Effects menu affect each
source independently.
Press the AVR Settings Button to display the menu system, and then
navigate to the Speaker Setup line. Press the OK Button to display
the Speaker Setup menu. Select Setup Listening Position 1 or 2,
press the OK Button, and then navigate to the Level Adjust line.
Press the OK Button to display the Adjust Speaker Levels menu.
See Figure 32.
Dolby Volume: See page 33 for an explanation of Dolby
Volume processing and its benefits. Refer to Table 3 on that page
for an explanation of each of the Dolby Volume settings.
Tone Control: Determines whether the treble and bass
controls are active. When it’s off, the tone controls are “flat”, with
no changes. When it’s on, the bass and treble frequencies are
boosted or cut, depending upon the tone-control settings. When an
analog audio source is in use and the 2-Channel Stereo surround
mode is selected, setting the Tone Control to “Off” places the unit
in analog bypass mode.
Treble and Bass: Boost or cut the high or low frequencies by
up to 10dB by using the 7/3Buttons to change the temperature
bar setting. The default setting is 0dB, at the center of the tempera-
ture bar.
Figure 32 – Adjust Speaker Levels Menu
LFE Trim: Attenuates the loudness of the subwoofer. The setting
defaults to the maximum of 0dB. Press the 7/3Buttons to reduce
the level by up to 10dB; the setting will appear as a negative number.
All of the speaker channels will appear with their current level settings.
Reset Levels: To reset all levels to their factory defaults of
0dB, scroll down to this line at the bottom of the menu and press
the OK Button.
EQ: This setting activates or deactivates the equalization settings
obtained when the EzSet/EQ II process was run. The settings are
saved for reactivation at a later listening session.
To set your levels using the AVR 7550HD’s internal test tone, adjust
the TEST TONE line as follows:
Speaker Setup: Select Position 1 or 2 to activate the speaker
configuration settings saved for the desired position. The settings
may be configured either by running the EzSet/EQ II process and
saving the results, or manually, as explained in the Manual Speaker
Setup section on page 41.
Test Tone: Determines whether the test tone is active. To begin,
press the OK Button repeatedly to select the OFF, AUTO or MANUAL
setting. Manually moving the cursor out of the channel listings area
of the screen automatically stops the test tone.
When you have finished, press the Audio Effects Button or the
Back/Exit Button.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
When displaying full-screen images on a widescreen device, black
or gray bars may appear to the left and right of the image (pillar-
boxing).
VIDEO ADJUSTMENTS
The AVR 7550HD uses leading-edge Faroudja DCDi Cinema video
processing technology. Incoming video is upscaled to 1080p (1080i
with component video outputs) for outstanding video quality, even
with analog video sources. The Faroudja DCDi Cinema Dual 3D
comb filters and 10-bit video processing eliminate the jagged
edges and moiré patterns seen with less advanced processing.
The “Torino” video processing chip generates on-screen graphics
in high definition, and blends it with the incoming video, so that
you can continue to watch a program while using system menus.
Plasma and CRT monitors may suffer from “burn-in” when the
same image, such as the horizontal or vertical bars, is left on screen
for a long period of time. Adjust the picture so that it fills the display’s
screen. Highlight this setting and press the OK Button. Each press
of the 1/5Buttons changes the setting. Press the OK Button when
the desired setting appears.
• Auto Fit: The AVR automatically adjusts the image, as required,
to fit the display’s capabilities.
The video processor automatically provides the best picture based
on the capabilities of your video display and the incoming source
video. You may experiment with the Video Modes menu adjustments
to try to improve the picture further.
• Height Fit: Adjusts the image to eliminate any bars above or
below it. Bars may remain at the sides.
• Width Fit: Adjusts the image to eliminate any bars on the
sides. Bars may remain above and below the image.
Video Modes
Adjust the picture settings on your video display before adjusting the
AVR. Access the picture settings from the Video Modes menu. Press the
Video Modes Button, and the screen shown in Figure 33 will appear.
The menu may also be accessed from the Info Settings menu.
• Zoom 1x: Displays the image as received from the source.
If the image is in the 4:3 aspect ratio, on widescreen displays
pillarbox format may be used. If the image is in the 16:9 aspect
ratio, on full-screen (4:3) displays letterbox format may be used.
NOTE: The settings in the Video Modes menu affect each
• Zoom 2x and Zoom 3x: Stretches the image evenly to
completely fill the screen. The outer portions of the image may
be cropped.
source independently.
Experiment with this setting until you find a pleasing display format
for each program.
Overscan: For historical reasons, there is a convention to
reserve an area around the border of a video frame, called “over-
scan”, that may be viewed on newer high-definition displays,
although it was not visible on older analog television sets. However,
since not all displays are capable of showing this portion of the
frame, directors avoid placing important information in that area. If
your video display is capable of displaying the overscan area, turn
this setting on to avoid seeing a black border around the image
which could cause unwanted “burn-in” on some plasma and CRT
displays. The AVR turns this setting off by default when the source
device is connected to one of the HDMI Inputs. The setting is turned
on by default when the source is connected to one of the analog
video inputs.
Figure 33 – Video Modes Menu
Video Mode: The default setting of Off passes the video signal
through to the display without any picture processing. Video scaling
cannot be turned off, but selecting the HDMI Bypass mode in the
Info Settings menu for a source connected to one of the HDMI Inputs
passes the video signal directly from the HDMI Input to the HDMI
Output, bypassing all video processing. Select one of these processing
options to optimize the picture for the current program by applying
adjustments to the brightness, contrast, color and sharpness:
Advanced Video Settings: Press the 3or OK Button to
display the Advanced Video Modes submenu (see Figure 34). This
submenu is not accessible when the video processor (Video Mode
setting) is turned off.
• Sports: For sporting events.
• Nature: For programs shot outdoors, in a natural setting.
• Movie: For movies and many television broadcasts.
• Custom: Allows manual adjustment of the picture settings. The
Brightness, Contrast, Color and Sharpness settings appear as
sliders with values ranging from 0 to 100. The default setting
for each adjustment is 50. Use the 7/3Buttons to change each
setting’s value.
Picture Adjust: Changes the aspect ratio of the displayed
image.
Widescreen (16:9) images are displayed on a full-screen (4:3)
device in letterbox format. Black bars may appear above and below
the image.
Figure 34 – Advanced Video Modes Menu
45
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Noise Reduction: Adjust this setting to Low, Medium or High
to filter out signal noise, or turn it off.
With a color bar test pattern from a test disc or other source on
screen, the following adjustments may be made:
• The color intensity setting on your TV.
MPEG Noise Reduction: This setting is designed to address
two specific types of video distortion, mosquito noise and blocking
artifacts. If you see haziness or shimmering around the edges of
objects or the scrolling credits in a film, or if the image appears to
“pixellate” into blocks, change the MPEG Noise Reduction setting
from Off to Low, Medium or High.
• Color adjustments using the color bars, which may be (left to
right) black, white, yellow, cyan (turquoise), green, magenta, red,
blue, black.
• The color transition, seen as sharp separation of the bars.
• The performance of the color circuits in your TV (with “Video”
signals); bar edges should show no vertical crawling dots.
Cross Color Suppressor: Turn this setting on to remove
cross color artifacts, which can occur when high-frequency luminance
(brightness) signals are misinterpreted as chroma (color) signals,
causing unwanted flickering, flashing colors or rainbow patterns.
Use the gray scale and the black/white fields in the test pattern to
adjust the brightness and contrast.
Brightness Adjustment
1. Turn down the color control on your TV until the color bars appear
in black and white.
Flesh Tone Enhancement: Turn this setting on to improve
the appearance of actors’ skin tones.
Black Level: This setting is only effective when used with the
Composite Video Output. Turn it on for a full black-level setting that
provides the full dynamic range of black as presented on most
DVDs. When turned off, the setting complies with NTSC standards
for video with “setup”, and may be more appropriate when your
video display has limited video processing capability.
2. Adjust the contrast to the lowest level where you still can see all
gray scale bars separately and clearly.
3. Adjust the brightness so that the bars in the gray scale are all
visible. The bar farthest to the left has to be as black as possible
rather than gray but the next gradation must clearly be distinct
from it. The bars in the gray scale should gradually and evenly
change from black to white.
Deinterlacing: For historical reasons, video in the NTSC format
was interlaced. That is, each refresh of the television screen dis-
played only half the pixels in a frame, alternating between all of the
even rows of pixels and all of the odd rows. Modern displays are
capable of displaying the complete frame all at once by progressively
scanning all of the rows of pixels from top to bottom. For optimal
viewing on a progressive-scan display (most flat-panel displays),
the video images must be deinterlaced. When viewing images via
the Composite or S-Video Monitor Output, or any time the AVR’s
video output resolution is 480i, this setting may be turned off.
Contrast Adjustment
1. Adjust the contrast on your TV until you see a bright white bar in
the lower right corner of the screen and a deep-dark-black bar to
the left.
2. If the brightness of the white bar no longer increases when the
contrast is turned up or the borders of white letters bloom (overlight)
into the black areas (drastically decreasing the sharpness of the
type), the contrast has been turned up too much. Reduce the contrast
until these effects disappear and the video still looks realistic.
Film Mode Detect: This setting is only accessible when the
Deinterlacing setting is turned on. It compensates for the different
frame rates in which film and video are shot. Film is shot at a rate
of 24 frames per second (progressive scan), while video is shot
at slightly less than 60 frames per second (interlaced). The AVR
is able to detect whether the program was originally shot on film
and transferred to video (e.g., to create a DVD), and to compensate
appropriately for any authoring errors in the conversion. Select a
setting of 3:2 (for NTSC materials), 2:2 (for PAL materials originating
overseas), Off or Auto.
3. If you are watching TV with ambient daylight, adjust the contrast
so that a normal video picture looks the same as the surround-
ings in your room; that way the eye is relaxed when watching
the TV picture. Reduce the setting when the surrounding light is
dimmed to improve the sharpness of the picture.
4. The gray scale in the middle line should retain the same distinc-
tion between each bar as before the contrast adjustment. If not,
repeat both Step 3 of the Brightness Adjustment and the Contrast
Adjustment.
How to Adjust the Custom Picture Settings
Set the Video Mode to Custom to display the picture settings, as
shown in Figure 35.
Color Adjustment
1. When the brightness and contrast are set optimally, adjust the
color control. Set the level so that the colors look strong but still
natural, not overdone. If the color level is too high, depending on
the TV, some of the bars will seem wider or the color intensity
will not increase when the control is turned up. Test the color
intensity with a video of pictures of faces, flowers, fruit and
vegetables.
2. Refer to the large white bar below the gray scale to tweak the
warmth of the picture using the Tint control on your TV.
Figure 35 – Video Modes Custom Processing
46
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
NOTE: Only analog audio sources, including The Bridge II,
Sharpness Adjustment
are available to the multizone system. The USB, Network and
Contrary to intuition, the picture will appear sharper and clearer
with the sharpness backed off from the maximum setting. Reduce
the sharpness setting on your television, and the setting on the
AVR 7550HD, if necessary, to minimize the appearance of any white
lines between the bars in the gray scale portion of the test screen.
Internet Radio sources are also available. To hear digital devices,
such as a CD player, in the remote zone, follow these steps:
1. In addition to a digital audio connection, connect the source
device’s analog audio outputs to the AVR. Make a note in
Table A5 in the appendix on which set of inputs was used.
Convergence and Edge Focus
2. In the Info Settings menu, leave the Audio Input From
Source setting at the digital audio input. Scroll down to the
Zone 2 Audio setting and select the analog audio input.
The crosshatch pattern that surrounds the test screen may be used
to evaluate edge focus and convergence in front- or rear-projection
video displays. If you are unable to improve the picture using the
available controls, contact the video display manufacturer’s authorized
service representative for assistance.
Volume: The volume is controlled separately for the remote zone.
Surround Back Amps: Reassign the surround back channels
to the multizone system. When this line is set to Zone 2, you may
only configure the main listening room for up to 5.2 channels.
EzSet/EQ II will only configure the main system. Use the Manual
Setup section of the Speaker Setup menu to configure the remote
speakers with this setting at Main Room, then return this setting
to Zone 2.
When you have finished making any video adjustments, press the
Back/Exit Button.
MULTIZONE OPERATION
With the multizone system in use, you may enjoy an exciting 5.1-
or 5.2-channel home theater presentation in the main listening
area, while others listen to the same materials or an entirely
different presentation in another room.
Carrier Out: The Carrier IR Output passes the full remote
infrared signal, rather than a signal stripped of the carrier frequency,
as is available at the Remote IR Output. This setting determines the
source for the Carrier IR Output.
Although installation of a multizone system is not complicated, it
requires running wires inside walls. Check your local building codes
and comply with the requirements for in-wall wiring systems, to
prevent the possibility of a dangerous situation. If you have any
questions about installing a multizone system, it is strongly recom-
mended that you contact a professional custom installer. See Step
Eleven of the Installation section on page 25 for instructions on
installing a multizone system.
• Zone 2: Uses the Zone 2 IR Input.
• Front Panel: Uses either the front-panel IR receiver or the Remote
IR Input.
• A-BUS: Uses the A-BUS system.
Operating the Multizone System
To operate the multizone system using the main remote, slide the
Zone Select Switch at the bottom of the remote to the “2” position.
To select a zone using the Zone 2 remote, press the Zone Selector,
and the Zone Indicator will turn green when the remote is set to
operate Zone 1, or red to operate Zone 2.
The AVR 7550HD’s multizone system is accessed using the on-
screen Zone 2 menu. Press the AVR Settings Button, and use the
1/5Buttons to navigate to the Zone 2 line. Press the OK Button to
display the Zone 2 menu. See Figure 36.
NOTE: When the Zone 2 Video Output is connected to a
display, a text-based version of the menu will appear. However,
no menus will appear when USB, Internet Radio or the Network
is selected as the source in either the main or remote zone,
and a different source is selected for the other zone.
SYSTEM SETTINGS
The AVR 7550HD offers system settings for ease of use. These
settings may be accessed from the System Settings menu, which
is selected by pressing the AVR Settings Button and navigating to
the System line. Press the OK Button to display the System Settings
menu. See Figure 37.
Figure 36 – Zone 2 Menu
Status: Turns the multizone system on or off. When no one is
listening in the remote room, leave this setting at the default of OFF.
Figure 37 – Systems Settings Screen
Front-Panel Dimmer: Select On 100% for full brightness,
dim to 50% or 25% of full brightness or select Off to fully darken
the display. The light inside the Volume Control will go out when the
display is partly or fully dimmed, but the Power Indicator will always
remain lit to remind you that the AVR is powered on.
Source: Indicates the source input for the remote zone. You may
select a different source from the main listening area. However, if the
same source has been selected for both the main listening area and
the remote zone, listeners in both areas will hear the same content.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
General AVR Settings
Menu Appearance
Network Settings: When the AVR is connected to a home
network router using the Network Jack, you may play shared content
stored on a PC or other device connected to the network, and you
may enjoy Internet Radio streams when the network is connected
to the Internet. If you are having difficulty accessing these sources,
check the Network Settings. Highlight the Network Settings line and
press the OK Button to view the Network Settings submenu.
Menu Transparency: Select whether video programs will
be visible when the menu system is in use. Select Normal for a fully
transparent background, Medium for partial transparency or Opaque
to block video programs while the menus are on screen.
Volume Status Messages: When the AVR is turned on,
the volume is adjusted or the source is changed, or if a change in
the input signal is detected, a status message will be displayed on
screen. Select how long the message remains visible, from 2 to
10 seconds, with a default of 3 seconds. Select “Off” if you do not
wish to see the status messages.
• ID #: This line is informational only, and identifies the AVR
to other devices on your home network and the Internet for
• Network Settings: If leaving this setting at “Automatic”
does not allow access, press the OK Button to change it to
“Manual” and adjust the other settings below it.
Menus: The settings in the Surround Modes, Video Modes and
Audio Effects menus only remain in effect during the current listening
session. This setting governs how long these menus remain visible
after the last adjustment: 5, 10 or 30 seconds, 1 minute or 5 min-
utes. Select “No Time-Out” to view the menus indefinitely, but this
setting is not recommended, due to the danger of “burn-in” on
some video displays.
• IP Address, Subnet Mask, Gateway, Primary
DNS, Secondary DNS: Depending on your system, this
information may be set automatically and may change each
time the AVR accesses the network for a new listening session.
Contact your ISP for this information.
Setup and Slide-In Menus: This setting determines how
long the setup menus (Main Menu, Speaker Setup Menu, Zone 2
Menu, all slide-in menus) remain visible after the last adjustment.
Select a time-out period of 5, 10 or 15 (the default) minutes, or no
time-out, which leaves the menus on screen until manually cleared.
A time-out period avoids the possibility of burn-in damage to plas-
ma or CRT displays.
• Proxy Address and Proxy Port: Some network security
systems access the Internet using a proxy server. Sometimes
filling in just this information correctly may resolve Internet
access issues.
Volume Units: Select whether volume is displayed in the
conventional decibel scale or on a numeric scale from 0 to 90.
When the decibel scale is used, 0dB is the maximum recommended
volume, with lower volumes displayed as negative values.
Screen Saver: Program a time-out period for no activity (with
no menus displayed) before the AVR’s built-in screen saver begins.
Select a period of 5, 10, 20 or 30 minutes or 1 hour, or turn off the
screen saver. A time-out period avoids the possibility of burn-in
damage to plasma or CRT displays.
Volume Default and Volume Default Level: These two
settings are used together to program the volume level at turn-on.
Turn Volume Default on, and then set the Volume Default Level to
the desired turn-on volume. When the Volume Default setting is left
off, the AVR will play at the last-used volume setting from the previ-
ous listening session.
System Information
Software Version: This line is informational only. From time
to time, Harman Kardon, Inc., may release software upgrades that
improve performance or add features. If you are experiencing diffi-
culties with the AVR, a customer service representative may ask for
the software version of your product to determine whether a later
upgrade is available.
Unit of Measure: Adjusts the speaker-distance settings for
Manual Speaker Setup. Select between meters and feet.
Language: Select the preferred language for the AVR’s on-screen
menus and displays: English, French, Spanish, German, Italian or
Russian.
Upgrade Software: If a software upgrade is released for
the AVR 7550HD, installation instructions will be available in the
Product Support section of the Web site or from Harman Kardon
Customer Service. At that time, you may access this submenu to
install the upgrade software.
HDMI Audio to TV: Determines whether HDMI audio signals
are passed through the HDMI Output to the video display. In normal
operation, leave this setting Off, as audio will be played through the
AVR. To use the TV by itself, without the home theater system, turn
this setting On. Mute the TV’s speakers when using the AVR for audio.
NOTE: During a system upgrade, do not power off the
AVR or use any of its controls. Doing so could permanently
damage the AVR.
Dolby Volume Calibration: This setting determines the
Dolby Volume Calibration Offset, as described on page 33. Its
default of 0dB is best when the system’s loudspeakers have a
sensitivity rating of 88dB (8 ohms, 1 watt, 1 meter). If your loud-
speakers have a higher sensitivity rating, increase the Dolby Volume
Calibration setting by the difference between your speakers’ sensi-
tivity and 88dB. If your speakers have a lower sensitivity, decrease
the Dolby Volume Calibration setting by the difference between
88dB and your speakers’ sensitivity.
ADVANCED REMOTE CONTROL
FUNCTIONS
The AVR 7550HD remote control also serves as a universal remote
that may be programmed to operate other components. Refer to the
Function List (Table A14 in the appendix) for assistance in operating
48
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
your other components. The function of each button will not neces-
sarily correspond to the label printed on the button.
NOTE: Use caution when programming complicated activities.
It isn’t possible to program a pause or delay before sending
commands after Power On, and the component may not be
ready to respond to commands immediately after powering on.
The AVR 7550HD remote is a sophisticated and versatile device that
is easy to program, thanks to its menu-based system.
To access the menu, press and hold the AVR Settings Button for at
least 3 seconds, until the remote’s Main Menu appears in its LCD
Text Display.
To program, or “record” an activity:
1. Press and hold the AVR Settings Button for 3 seconds. The
remote will enter Program mode, and its Main Menu will be
displayed.
The remote’s menu is navigated using the 1/57/3Buttons and
the OK Button. Scroll up or down to a desired menu option, and
press the OK Button to select it.
2. Use the 1/5 Buttons to scroll to the Activity option, and press
the OK Button.
3. Use the 1/5Buttons to select the Record Activity option, and
press the OK Button.
Main Menu
• Program Device: Used to program the control codes for a
source device into the appropriate Source Selector. See page 26
in the Installation section for detailed instructions.
4. Use the 1/5 Buttons to select the command button, and press
the OK Button. The command button is the key the user will
press to execute the activity. Select the AVR Power On Button,
the AVR Power Off Button or one of the Alphanumeric Keys.
• Learn: Used to “learn” control codes from a source device’s
original remote, or to delete previously learned codes for individual
keys or entire devices. See page 27 in the Installation section for
detailed instructions.
NOTE: When one of the Alphanumeric Keys is used as
the command button, first press the Activity Button, then
the Alphanumeric Key, to execute the activity. When the
Alphanumeric Key is pressed by itself, the activity will not
be executed. However, when the AVR Power On Button or the
AVR Power Off Button is selected as the command button,
the activity will be executed every time the programmed
AVR Power Button is pressed.
• Change Device: Used while programming a Source Selector
when the source device doesn’t match the Source Selector’s
device type. For example, when the system uses two DVD players
but no media server, you may program the second DVD player’s
control codes into the Media Server Source Selector by changing
its device type to DVD. See page 27 in the Installation section for
detailed instructions.
5. Use the 1/5Buttons to select the last source, and press the
OK Button. This places the AVR and the remote in the desired
device mode after the Activity is finished.
• Activity: Used to program a sequence of up to 20 commands
into one of 10 activities so that the sequence may be executed by
pressing only two buttons (Activity Button and Alphanumeric Key
for the specific activity). See below for detailed instructions.
6. Begin pressing the keys for the desired commands. Each com-
mand will appear in the LCD Display, with the source in use
shown in square brackets on the left.
• To switch to another source, press its Source Selector. This will
count as one of the 20 commands allowed in each activity.
• Punch-Through: Used to allow transport- or channel-control
of a different system component than the one currently being
used. See below for detailed instructions.
• To include the AVR Power On or AVR Power Off commands, first
press the AVR Settings Button to set the remote in AVR device
mode, then press the desired power button.
• Rename: Used to rename a Source Selector or key on the
remote to correspond to its actual function. Renaming only
affects information appearing in the remote’s LCD Text Display.
See page 27 in the Installation section for detailed instructions.
• To program menu navigation, press the 3Button to make a
selection, and press the 7 Button to return to a previous menu
level. Pressing the OK Button will end the command sequence
and save it as an activity, while pressing the Back/Exit Button
will exit Program mode without saving the activity.
• Back Light: Used to program the functioning of the remote’s
back light. See below for detailed instructions.
7. To end the command sequence, press the OK Button.
• Remote Reset: Used to reset the remote to its factory
defaults, deleting all user programming. See below for detailed
instructions.
8. Use the 1/5 Buttons to select either the End Activity option or
the Edit Title option, and press the OK Button.
• Exit: Exits the remote’s Program Mode when you scroll to this
option and press the OK Button.
• End Activity: The activity will be saved. When the activity
is executed, its command button, e.g., Activity 9, will appear
in the LCD Display.
Activities (Macros)
• Edit Title: You may name the activity, e.g., All Power Off.
When the activity is executed, its name will appear in the LCD
Display. When this option is selected, the cursor will flash. Type
the title for the activity using the Alphanumeric Keys. Each
Alphanumeric Key has the characters available in addition to
its number printed above the key. Each press of the key scrolls
Activities are used to program sequences of up to 20 commands
that are executed with a single button press. Activities are well
suited for power-on and -off commands, to send out a multidigit
channel number with one button press, or to control another device
with more flexibility than the built-in punch-through controls. Up to
11 activities may be programmed.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
through the available characters. To move to the next character,
either press the 3Button, or press the next desired Alphanumeric
Key. Press the OK Button when you have finished.
5. Use the 1/5Buttons to select the punch-through device
(CBL/SAT in the example given in step 4), press the OK Button,
and the Punch-Through programming will be saved.
To execute an activity, press the Activity Button, then the Alphanumeric
Key you selected as the command button in Step 4. If you selected
the AVR Power On or Off Button in Step 4, you do not need to press
the Activity Button first.
To undo punch-through programming, follow the same steps as
above, but select the same Source in Steps 4 and 5.
NOTE: The Volume and Mute controls are always dedicated
to the AVR.
To view the steps previously programmed for an activity without
executing it:
Back Light
1. Press and hold the AVR Settings Button for 3 seconds. The
remote will enter Program mode, and its Main Menu will be
displayed.
The AVR remote is equipped with a back light to illuminate the keys
and LCD Display to facilitate its use in a darkened home theater
environment.
2. Use the 1/5 Buttons to scroll to the Activity option, and press
the OK Button.
To turn the back light on or off at any time, press the Back Light Button.
The back light’s turn-on mode may be programmed:
3. Use the 1/5Buttons to select the Read Activity option, and press
the OK Button.
4. Use the 1/5Buttons to select the command button, and press
the OK Button.
• Normal: The back light stays off unless the Back Light Button
is pressed.
5. Use the 1/5Buttons to scroll through the steps programmed
into the activity. It is not possible to make any changes. When
you have finished, press the OK Button or the Back/Exit Button
to exit Program mode.
• On Full: The back light will turn on any time a key is pressed.
In both modes, the back light will remain on for 5 seconds after the
last button press, and then turn off automatically.
It isn’t possible to “edit” a command within an activity. To delete the
activity:
To program the remote’s back light mode:
1. Press and hold the AVR Settings Button for 3 seconds. The remote
will enter Program mode, and its Main Menu will be displayed.
1. Press and hold the AVR Settings Button for 3 seconds. The
remote will enter Program mode, and its Main Menu will be
displayed.
2. Use the 1/5Buttons to scroll to the Activity option, and press
the OK Button.
3. Use the 1/5Buttons to select the Delete Activity option, and
press the OK Button.
2. Use the 1/5Buttons to scroll to the Back Light option, and press
the OK Button.
4. Use the 1/5Buttons to select the command button or title, and
press the OK Button. The activity, including any title you gave it,
will be deleted.
3. Use the 1/5Buttons to select the Normal or On Full option, and
press the OK Button to finish.
Punch-Through Programming
Remote Reset
The punch-through feature allows you to operate one component,
while setting certain groups of controls to operate another component.
For example, while using the AVR controls for surround modes and
other audio functions, you may operate the transport controls of
your DVD player. Or while using the remote to control video functions
on your TV, you may use your cable box to change channels.
To reset the remote to its factory defaults, erasing all product
codes, learned codes, activities and other user programming:
1. Press and hold the AVR Settings Button for 3 seconds. The
remote will enter Program mode, and its Main Menu will be
displayed.
To program punch-through control while operating any device:
1. Press and hold the AVR Settings Button for 3 seconds. The
remote will enter Program mode, and its Main Menu will be
displayed.
2. Use the 1/5Buttons to scroll to the Remote Reset option, and
press the OK Button. The process may take a few minutes,
depending on the amount of user programming requiring erasure.
Please wait until the “Remote Reset Complete” message appears
before pressing any keys.
2. Use the 1/5Buttons to scroll to the Punch-Through option,
and press the OK Button.
3. Use the 1/5Buttons to select either Channel or Transport
control, and press the OK Button.
4. Use the 1/5Buttons to scroll to the device in use, and press
the OK Button. For example, to change channels using the cable
or satellite set-top box while using the remote to operate the TV,
select the TV source in this step.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
PROCESSOR RESET
If the unit behaves erratically after a power surge, first turn off
the Main Power Switch and unplug the AC power cord for at least
3 minutes. Plug the cord back in and turn the receiver on. If this
doesn’t help, reset the AVR.
NOTE: A system reset erases all user configurations, including
video resolution, speaker and level settings, and tuner presets.
After a reset, reenter all of these settings from your notes in
the appendix worksheets.
To reset the AVR 7550HD, place it in Standby mode (press the front-
panel Standby/On Switch so that the Power Indicator turns amber).
Then press the front-panel AVR Settings and Source List Buttons
simultaneously until the RESET message appears.
If the receiver does not function correctly after a processor reset,
contact an authorized Harman Kardon service center for assistance.
Authorized service centers may be located by visiting the Web site
NOTE: After performing a system reset, wait at least 1 minute
before pressing any Source Selectors. If The Bridge Source
Selector is pressed too soon, video playback from the iPod will
not be available.
MEMORY
If the AVR 7550HD is unplugged or experiences a power outage, it
will retain user settings for up to four weeks.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
SYMPTOM
CAUSE
SOLUTION
Unit does not function when Main
Power Switch is turned on
• No AC Power
• Make certain AC power cord is plugged into a live outlet
• Check whether outlet is switch-controlled
Display lights, but no sound
or picture
• Intermittent input connections
• Mute is on
• Secure all input and speaker connections
• Press Mute Button
• Volume control is down
• Turn up volume control
No sound from any speaker;
PROTECT message appears on
front panel
• Amplifier is in protection mode
due to possible short
• Amplifier is in protection mode
due to internal problems
• Check speaker wires for shorts at receiver and speaker ends
• Contact your local Harman Kardon service center
No sound from surround or
center speakers
• Incorrect surround mode
• Input is monaural
• Incorrect configuration
• Stereo or Mono program material
• Select a mode other than Stereo
• There is no surround information from mono sources
• Check speaker configuration
• The surround decoder may not create center- or rear-channel
information from nonencoded programs
Unit does not respond to
remote commands
• Weak batteries in remote
• Wrong device selected
• Remote sensor is obscured
• Change remote batteries
• Press the AVR Settings Button
• Make certain front-panel sensor is in line of sight of remote
or connect an optional remote sensor
Intermittent buzzing in tuner
• Local interference
• Move unit or antenna away from computers, fluorescent
lights, motors or other electrical appliances
Surround Back Speaker settings
cannot be accessed, and test tone
does not play through Surround
Back Speakers
• Multizone system has been turned
on, and the surround back channels
were reassigned to multizone
operation
• Use the menu system to access the Zone 2 menu and reassign
the surround back channels to the main room
The XM Preview Channel (001)
is silent
• XM antenna is not plugged in
• Use an XM antenna module designed for use with XM Ready home
audio equipment, and plug the module into the XM Radio Jack
• The XM antenna module needs an unobstructed view of the
southern sky, or to be within range of an XM terrestrial repeater;
if necessary, purchase an extension cable from your XM Radio dealer
• XM antenna is not located in such
a way as to enable reception
• XM signal requires a refresh
Unable to activate Program mode
on remote
• AVR Settings Button not held for at
least 3 seconds
• Follow the instructions in the remote’s LCD Display
Remote buttons light, but AVR does
not respond
• Remote is in Zone 2 mode
• Slide the Zone Switch at the bottom of the remote to the
Zone 1 position
Unable to play Internet Radio
• AVR is not able to access the Internet • Make sure the Network Jack is connected to an active router;
navigate to the Network Settings submenu in the System Setup
menu and change the Network Settings line to “Manual”; contact
your ISP to obtain the correct information for the other settings in
this submenu
Unable to access content on PC
from Network source
• Content not in proper format
• Only content in the form of MP3, WMA and JPEG files may be shared
with the AVR
• Content has not been shared by
network device
• Network device must be running compatible software; network device
must be programmed to share the content over the network; refer to
the Network Playback section on page 37 for details
Additional information on troubleshooting possible problems with your AVR 7550HD, or installation-related issues, may be found in the list of “Frequently
52
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Appendix – Default settings, worksheets, remote product codes
Table A1 – Recommended Source Component Connections
Device Type
AVR 7550HD Source
Digital Audio Connection Analog Audio Connection Video Connections
Cable TV, satellite TV, HDTV
or other device that delivers
television programs
CBL/SAT
HDMI 2
Analog 1
HDMI 2
DVD Audio/Video, SACD,
Blu-ray Disc, HD-DVD player
DVD
HDMI 1
HDMI 4
Analog 2
Analog 5
HDMI 1
Media Server, including
Media Server
HDMI 4
Harman Kardon DMC 1000
TV
TV
Optical 1
HDMI 3
Analog 3
Component 1
*
Video game console
Game
AUX
Analog 4
HDMI 3
Any audio or video device,
e.g., CD player, camcorder,
cassette deck
Coax Front
Analog Front
Composite Front (not used for
audio-only devices)
Recorder
Source D
Coaxial 2 input and
Coaxial Output
Analog 4 inputs and outputs
The Bridge II
Composite OR S-Video 2 input
and output
iPod
The Bridge II
None
The Bridge II for photo- and
video-capable iPod models
Make this connection only when using the TV source for a non-display device. Do not connect your television’s or video display’s video output to the AVR at any time.
*
NOTE: Additional components may be connected to available audio and video inputs and assigned to Sources A, B, C and D. A USB drive may be plugged into the front-panel USB Port. For
access to content on network computers and other devices, and to enjoy Internet Radio, connect the Network Jack to a home-network router. See pages 36 and 37 for more information.
Table A2 – Source Setting Defaults
Cable/Sat
DVD
Media Server Radio
TV
Game
AUX
The Bridge
Surround Modes (Auto Select) Logic 7 Movie Logic 7 Movie Logic 7 Music
Logic 7 Movie Logic 7 Movie Logic 7 Movie Logic 7 Music
Logic 7 Music
Video Input
HDMI 2
HDMI 2
480i
HDMI 1
HDMI 1
480i
HDMI 4
HDMI 4
480i
N/A
Component 1 HDMI 3
Composite Front The Bridge II
Audio Input
N/A
Optical 1
480i
HDMI 3
480i
Coaxial Front
480i
The Bridge II
480i
Resolution to Display
Audio Auto Polling
Zone 2 Audio
480i
N/A
*
Off
Off
Off
Off
Off
Off
N/A
Analog 1
Analog 2
Analog 5
Radio
N/A
Analog 3
Analog 4
Analog Front
The Bridge II
The Bridge II
Zone 2 Video
Composite
Video 1
Composite
Video 2
Composite
Video 3
Composite
Video 2
Composite
Video 3
Composite
Video Front
Trigger 2
On
On
On
On
On
On
On
On
Dolby Volume
Record Out
Medium
Analog
Low
Medium
Analog
Medium
Analog
Medium
Analog
Medium
Analog
Low
Medium
Analog
Analog
Analog
*
Video output resolution may vary for HDMI connections.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
continued
Table A2 –
USB
Internet Radio Network
Source A
Source B
Source C
Source D
Surround Modes (Auto Select) Logic 7 Movie
Logic 7 Music
Internet Radio
Logic 7 Music
Network
Logic 7 Movie Logic 7 Movie
Logic 7 Movie
Logic 7 Movie
Video Input
USB
Component
Video 2
Component
Video 3
Composite
Video 1
Composite
Video 2
Audio Input
USB
480i
N/A
USB
N/A
N/A
Network
480i
Optical 2
480i
Optical 3
480i
Analog 1
480i
Coaxial 2
480i
Resolution to Display
Audio Auto Polling
Zone 2 Audio
480i
N/A
N/A
Off
Off
Off
Off
Internet Radio
N/A
Network
N/A
Analog 1
Analog 2
Analog 3
Analog 4
Zone 2 Video
Composite
Video 1
Composite
Video 2
Composite
Video 3
Composite
Video Front
Trigger 2
On
On
On
On
On
On
On
Dolby Volume
Record Out
Medium
Analog
Medium
Analog
Medium
Analog
Medium
Analog
Medium
Analog
Medium
Analog
Medium
Analog
Table A3 – Speaker/Channel Setting Defaults
All Digital and 2-Channel
Analog Audio Inputs
6-/8-Channel
Analog Audio Inputs* Position 1
Your Settings
Your Settings
Position 2
Left/Right Speakers
ON
ON
ON
ON
OFF
ON
ON
Center Speaker
ON
Left/Right Surround Speakers
Left/Right Surround Back Speakers
Subwoofer 1
ON
OFF
ON
Subwoofer 2
ON
Left/Right Speakers Crossover
Center Speaker Crossover
Left/Right Surround Speakers Crossover
100Hz
100Hz
100Hz
Large
*
Large
*
Large
*
Left/Right Surround Back Speakers Crossover 100Hz
Large
*
Subwoofer Mode
Subwoofer 1 Size
Subwoofer 2 Size
Front Left Level
LFE
LFE
*
10 inch
10 inch
0dB
ON
OFF
0dB
0dB
0dB
0dB
0dB
0dB
0dB
0dB
Center Level
0dB
Front Right Level
Surround Right Level
Surround Back Right Level
Surround Back Left Level
Surround Left Level
Sub Level
0dB
0dB
0dB
0dB
0dB
0dB
Note: When the Tone Mode setting is Off, the 6-/8-Channel Inputs are “direct” inputs whose signals are passed directly to the volume control without any bass management
processing. The speakers remain full-range and cannot be adjusted. When the Tone Mode setting is On, the defaults are the same as for the other audio inputs. The settings
are global for the remaining audio inputs.
*
54
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A4 – Delay Setting Defaults
Distance From Speaker to
Listening Position
Your Delay Settings
Position 1
Your Delay Settings
Position 2
Speaker Position
Front Left
12 feet
Center
12 feet
Front Right
12 feet
Surround Right
10 feet
Surround Left
10 feet
Surround Back Right
Surround Back Left
Subwoofer 1
10 feet
10 feet
12 feet
Subwoofer 2
12 feet
A/V Lip Sync Delay (See Info Settings Menu)
0mS
Table A5 – Source Settings
Cable/Sat DVD
Media Server Radio
TV
Game
AUX
The Bridge
Device Type
Surround Modes
Video Input
The Bridge II
The Bridge II
Audio Input
Resolution to Display
Adjust Lip Sync
Change Name
Audio Auto Polling
Zone 2 Audio
Zone 2 Video
Trigger 2
N/A
N/A
The Bridge II
Dolby Volume
Record Out
55
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
continued
Table A5 –
USB
Internet Radio Network
Source A
Source B
Source C
Source D
Device Type
USB Drive
N/A
Surround Modes
Video Input
USB
USB
N/A
Network
Network
Audio Input
Internet Radio
Resolution to Display
Adjust Lip Sync
Change Name
Audio Auto Polling
Zone 2 Audio
Zone 2 Video
Trigger 2
N/A
USB
N/A
N/A
N/A
Internet Radio
N/A
Network
N/A
Dolby Volume
Record Out
Table A6 – Audio Effects Settings
Default
See Source
Off
Cable/Sat DVD
Media Server Radio
TV
Game
AUX
The Bridge
Dolby Volume
Tone Control
Treble
0dB
Bass
0dB
LFE Trim
EQ
0dB
On
Speaker Setup
Position 1
continued
Table A6 –
USB
Internet Radio Network
Source A
Source B
Source C
Source D
Dolby Volume
Tone Control
Treble
Bass
LFE Trim
EQ
Speaker Setup
56
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A7 – Video Modes Settings
Default
Cable/Sat DVD
Media Server Radio
TV
Game
AUX
The Bridge
Video Mode
Off
Brightness
50
*
Contrast
50
*
Color
50
*
Sharpness
50
*
Picture Adjust
Overscan
Auto Fit
On
Noise Reduction
Low
Low
On
**
MPEG Noise Reduction
**
Cross Color Suppressor
**
Flesh Tone Enhancement
Off
**
Black Level
Off
**
Deinterlacing
On
**
Film Mode Detect
3:02
**
continued
Table A7 –
USB
Internet Radio
Network
Source A
Source B
Source C
Source D
Video Mode
Brightness
*
Contrast
*
Color
*
Sharpness
*
Picture Adjust
Overscan
Noise Reduction
**
MPEG Noise Reduction
**
Cross Color Suppressor
**
Flesh Tone Enhancement
**
Black Level
**
Deinterlacing
**
Film Mode Detect
**
Note: These settings are only available when the Video Mode is set to Custom.
**Note: These settings are only displayed when Advanced Video Settings is selected.
*
57
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A8 – Surround Modes
Default
Cable/Sat DVD
Media Server Radio
TV
Game
AUX
The Bridge
Auto Select
Logic 7 Movie or
native digital format
Virtual Surround
Dolby Virtual
Speaker Reference
Stereo
Movie
Music
Game
5 CH Stereo
Logic 7 Movie
Logic 7 Music
Logic 7 Game
Center Width
0
*
Dimension
0
*
Panorama
Off
*
continued
Table A8 –
USB
Internet Radio
Network
Source A
Source B
Source C
Source D
Auto Select
Virtual Surround
Stereo
Movie
Music
Game
Center Width
*
Dimension
*
Panorama
*
Note: These settings are only available when Dolby Pro Logic II or IIx Music mode has been selected. Access these settings by selecting the Edit option.
*
Table A9 – Remote Control Codes
Source Input
Device Type (if changed)
Product Brand and Code Number
Cable/Sat
DVD
Media Server
TV
Game
AUX
Source A (Red Soft Key)
Source B (Green Soft Key)
Source C (Yellow Soft Key)
Source D (Blue Soft Key)
58
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A10 – System Settings
Feature
Default
On 100%
dB
Your Settings
Front-Panel Dimmer
Volume Units
Volume Default
Off
Volume Default Level
Unit of Measure
–25dB
Feet
Language
English
Off
HDMI Audio to TV
Dolby Volume Calibration
Menu Transparency
Volume/Status Messages
Menus
0dB
Medium
3 seconds
1 minute
15 minutes
10 minutes
Check your product
Setup and Slide-In Menus
Screen Saver
Software Version
Table A11 – Network Settings
Setting
Your Settings
ID #
Network Settings
IP Address
Subnet Mask
Gateway
Primary DNS
Secondary DNS
Proxy Address
Proxy Port
Table A12 – Zone 2 Settings
Source Input
Default
Off
Your Settings
Status
Source
FM Radio
–25dB
Volume
Surround Back Amps
Carrier Out
Main Room
Zone 2
59
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A13 – Surround Modes
Surround Mode
Description
Incoming Bitstream or Signal
Dolby Digital
Provides up to five separate main audio channels and a dedicated
low-frequency effects (LFE) channel.
• Dolby Digital 1/0/.0 or .1, 2/0/.0 or .1,
3/0/.0 or .1, 2/1/.0 or .1, 2/2/.0 or .1,
3/2/.0 or .1
• Dolby Digital EX (played as 5.1)
• Dolby Digital Plus decoded and delivered
via coax or optical connection
Dolby Digital EX
An expansion of Dolby Digital 5.1 that adds a surround back channel
which may be played through one or two surround back speakers. May
be manually selected when a non-EX Dolby Digital stream is detected.
• Dolby Digital EX
• Dolby Digital 2/2/.0 or .1, 3/2/.0 or .1
Dolby Digital Plus
An enhanced version of Dolby Digital encoded more efficiently, Dolby
Digital Plus has the capacity for additional discrete channels and for
streaming audio from the Internet, all with enhanced audio quality. Source
material may be delivered via an HDMI connection, or decoded to Dolby
Digital or PCM and transmitted via S/P-DIF coaxial or optical digital audio.
• Dolby Digital Plus via HDMI connection
(source device decodes to Dolby Digital
when a coax or optical connection is used)
Dolby TrueHD
Dolby TrueHD is an expansion of MLP Lossless™ audio, the same format
used on DVD Audio discs. Dolby TrueHD adds the features found in
Dolby Digital, such as night mode settings, while delivering fully lossless
audio that is a true reproduction of the studio master recording.
• Blu-ray Disc or HD-DVD encoded with
Dolby TrueHD, delivered via HDMI
Dolby Digital Stereo
Delivers a 2-channel downmix of Dolby Digital materials.
• Dolby Digital 1/0/.0 or .1, 2/0/.0 or .1,
3/0/.0 or .1, 2/1/.0 or .1, 2/2/.0 or .1,
3/2/.0 or .1
• Dolby Digital EX
Dolby Pro Logic II
Mode Group
Analog decoder that derives five full-range, discrete main audio channels See below
from matrix surround-encoded or 2-channel analog sources. Four variants
are available.
Dolby Pro Logic II
Movie
Variant of Dolby Pro Logic II that is optimized for movie and
television programs.
• Dolby Digital 2.0 or 2.1
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
Dolby Pro Logic II
Music
Variant of Dolby Pro Logic II that is optimized for music selections.
Allows adjustment of sound field presentation in three dimensions:
• Center Width (adjusts width of vocal soundstage)
• Dimension (adjusts depth of soundstage)
• Dolby Digital 2.0 or 2.1
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Panorama (adjusts wraparound surround effect)
Dolby Pro Logic II
Game
Variant of Dolby Pro Logic II that emphasizes use of the surround
channels and subwoofer for total immersion in the video gaming
experience.
• Dolby Digital 2.0 or 2.1
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
Dolby Pro Logic
Original version of Dolby Pro Logic that steered a mono signal
containing information below 7kHz to the surround channels.
• Dolby Digital 2.0 or 2.1
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
60
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A13 – continued
Surround Mode
Description
Incoming Bitstream or Signal
Dolby Pro Logic IIx
Mode Group
An expansion of Dolby Pro Logic II that adds a surround back channel
which may be played through one or two surround back speakers. The
Dolby Pro Logic IIx modes may be selected not only with Dolby Digital bit-
streams, but thanks to the AVR 7550HD’s post-processor, they may also be used
with some DTS bitstreams to add a surround back channel to 5.1 modes.
Dolby Pro Logic IIx
Movie
This mode is similar to Dolby Pro Logic II Movie, with an added surround
back channel.
• Dolby Digital 2/0/.0 or .1, 2/2/.0 or .1,
3/2/.0 or .1, EX
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
Dolby Pro Logic IIx
Music
This mode is similar to Dolby Pro Logic II Music, including the availability
of center width, dimension and panorama adjustments. Dolby Pro Logic IIx
Music adds a surround back channel.
• Dolby Digital 2/0/.0 or .1, 2/2/.0 or .1,
3/2/.0 or .1, EX
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
Dolby Pro Logic IIx
Game
This mode is similar to Dolby Pro Logic II Game, with the added benefit
of a surround back channel.
• Dolby Digital 2/0/.0 or .1
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz or 48kHz)
Dolby Virtual Speaker Simulates 5.1 channels when only two speakers are present, or a more
Mode Group enveloping sound field is desired.
See below
Dolby Virtual Speaker When only two main speakers are present, the Reference mode virtualizes • Dolby Digital (uses only two-speaker mode
Reference
a full surround presentation with accurate localization.
when signal does not contain center channel
information)
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz or 48kHz)
Dolby Virtual Speaker Wide mode may be used with two main speakers to widen the front
• Dolby Digital (number of channels available
varies by number of channels in signal)
• Analog (2-channel)
Wide
soundstage by virtualizing the locations of the left and right speakers.
• Tuner
• PCM (32kHz, 44.1kHz or 48kHz)
DTS Digital
DTS-HD
Using a different encoding/decoding method than Dolby Digital, it also
provides up to five discrete main channels, plus an LFE channel.
• DTS 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1,
3/1/.0 or .1, 2/2/.0 or .1, 3/2/.0 or .1
• DTS-ES Matrix (played as 5.1)
• DTS-ES Discrete (played as 5.1)
DTS-HD is a new high-definition audio format that complements the
high-definition video found on Blu-ray Disc and HD-DVD discs. It is
transmitted using a DTS core with high-resolution extensions. Even when
only DTS 5.1 surround sound is desired (or available, if the multizone
system is in use), the higher capacity of high-resolution discs serves up
DTS at twice the bit rate used on DVD-Video discs.
• Blu-ray Disc or HD-DVD discs encoded
with DTS-HD modes, delivered via HDMI
DTS-HD Master Audio DTS-HD Master Audio technology delivers bit-for-bit reproductions of the
studio master recording in up to 7.1 channels, for an incredibly accurate
performance.
• Blu-ray Disc or HD-DVD discs encoded with
DTS-HD Master Audio technology, delivered
via HDMI
61
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A13 – continued
Surround Mode
Description
Incoming Bitstream or Signal
DTS-ES Matrix
DTS Extended Surround adds a single surround back channel to DTS 5.1
digital surround sound. The Matrix version includes the surround back
channel information “matrixed” into the left and right (side) surround
channels, for compatibility with 5.1-channel systems.
• DTS-ES Matrix
DTS-ES Discrete
DTS Stereo
DTS-ES Discrete is another Extended Surround mode that adds a surround • DTS-ES Discrete
back channel, but this information is encoded discretely on the disc, and
is not derived from information contained in the surround channels.
Delivers a 2-channel downmix of DTS Digital materials, or presents
a matrix-encoded surround presentation.
• DTS 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1,
3/1/.0 or .1, 2/2/.0 or .1, 3/2/.0 or .1
• DTS 96/24
• DTS-ES Matrix
• DTS-ES Discrete
DTS Neo:6
Mode Group
DTS Neo:6 analog processing is available with DTS and DTS 96/24
signals and 2-channel analog or PCM signals to create a 3-, 5- or 6-channel
presentation.
See below
DTS Neo:6
Cinema
Depending on the number of speakers in your system, select 3-, 5- or
6-channel modes, enhanced for movie or video presentations.
• DTS 2/2/.0 or .1, 3/2/.0 or .1
• DTS 96/24
• Analog (2-channel)
• PCM (32kHz, 44.1kHz or 48kHz)
DTS Neo:6
Music
Available only in 5- and 6-channel modes, creates a surround presentation • DTS 2/2/.0 or .1, 3/2/.0 or .1
suitable for music recordings.
• DTS 96/24
• Analog (2-channel)
• PCM (32kHz, 44.1kHz or 48kHz)
Logic 7
Mode Group
A Harman International proprietary technology, Logic 7 technology enhances
2-channel and matrix-encoded recordings by deriving separate information
for the surround back channels. This provides more accurate placement of
sound, improves panning and expands the sound field, even when used
with 5.1-channel systems. Logic 7 technology uses 96kHz processing, and
is available in 5.1-or 7.1-channel modes. Three variants are available.
See below
Logic 7
Movie
Especially suited to 2-channel sources containing Dolby Surround or matrix • Analog (2-channel)
encoding, Logic 7 Movie mode increases center channel intelligibility.
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
Logic 7
Music
The AVR 7550HD is programmed at the factory to default to this mode for • Analog (2-channel)
2-channel signals. Logic 7 Music mode is well suited to conventional
2-channel music recordings.
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
Logic 7 Game
Use Logic 7 Game mode to enhance enjoyment of video game consoles.
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
5-Channel Stereo
7-Channel Stereo
Useful for parties, the left- and right-channel information is played
through both the front and surround speakers on each side, while the
center speaker plays a summed mono mix.
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz or 48kHz, 96kHz, 192kHz)
Expands the 5-Channel Stereo presentation to include the surround back
channels.
• Analog (2-channel)
• Tuner
• PCM (32kHz, 44.1kHz or 48kHz, 96kHz, 192kHz)
62
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A13 – continued
Surround Mode
Description
Incoming Bitstream or Signal
2-Channel Stereo
Turns off all surround processing and plays a pure 2-channel signal
or a downmix of a multichannel signal. The signal is digitized and bass
management settings are applied, making it appropriate when a
subwoofer is used.
• Analog (2-channel; DSP downmix available
for multichannel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
2-Channel Stereo
(Analog Bypass)
Maintains an analog input signal in that form, bypassing all digital processing • Analog (2-channel)
(i.e., surround and bass management). Requires Tone Control setting to be off. • Tuner
63
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
1
2
3
4
5
6
7
8
9
10 11 12 13 14
15
16
17
18
21
24
27
19
22
25
28
20
23
26
29
30
33
31
32
34
37
35
36
38
39 40 41 42
44
43
45
46
47
48
51
49
52
50
53
Refer to the numbered buttons in Figure 38
when using the Function List.
54 55 56 57
58
Figure 38 – Remote Control Function List Reference
64
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A14 – Remote Control Function List
Radio
Media Server
No.
Button Name
AVR
FM
AM
XM
DVD
DMC1000
TV
The Bridge
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
AVR Power On
AVR Power Off
Device Power On
Device Power Off
Cable/SAT
DVD
The Bridge
USB
Radio
TV
Game
Media Server
AUX
Network
Audio Effects
Video Modes
AVR Power On
AVR Power Off
AVR Power On
AVR Power Off
AVR Power On
AVR Power Off
AVR Power On
AVR Power Off
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
AVR Power On
AVR Power Off
On
Off
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Input Sel
Input Sel
Input Sel
USB
Input Sel
Input Sel
Input Sel
USB
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Radio
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Audio Effects
Video Modes
Surround Modes
Surround Modes
Surround Modes
Surround Modes Surround Modes
Surround Modes
Surround Modes
Surround Modes
Surround Modes
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
9
Last
0
Activity
Back/Exit
Last
0
Activity
Back/Exit
Menu
Up
Last
0
Activity
Back/Exit
Menu
Up
Left
OK
Right
Light
Down
Last
0
Last
0
Prev. Ch
0
Activity
Last
0
Activity
Back/Exit
Menu
Up
Left
OK
Right
Light
Down
0
Activity
Clear
Menu
Up
Left
Enter
Right
Light
Down
Disc Menu
Angle
Subtitle
Audio
Zoom
AVR Volume +
AVR Volume –
AVR Mute
Page Up
Page Down
Prev. Step
Pause
Next Step
Rew 77
Play 3
0
Activity
Back
Menu
Up
Left
Enter
Right
Light
Down
Disc Menu
Angle
Subtitle
Audio
Zoom
AVR Volume +
AVR Volume –
AVR Mute
Activity
Back/Exit
Menu
Tune Up
Preset/Down
OK
Preset/Up
Light
Tune Down
Activity
Back/Exit
Menu
Tune Up
Preset/Down
OK
Preset/Up
Light
Tune Down
Menu
Menu
Up
Left
Channel/Preset Up
Preset/Category Down
OK
Preset/Category Up
Light
Left
OK
OK
Right
Light
Down
Disc Menu
Red
Green
Yellow
Blue
Volume +
Volume –
Mute
Right
Light
Down
OSD
Channel/Preset Down
Input Sel (A)
Input Sel (B)
Input Sel (C)
Input Sel (D)
AVR Volume +
AVR Volume –
AVR Mute
Input Sel (A)
Input Sel (B)
Input Sel (C)
Input Sel (D)
AVR Volume +
AVR Volume –
AVR Mute
Input Sel (A)
Input Sel (B)
Input Sel (C)
Input Sel (D)
AVR Volume +
AVR Volume –
AVR Mute
Input Sel (A)
Input Sel (B)
Input Sel (C)
Input Sel (D)
AVR Volume +
AVR Volume –
AVR Mute
Input Sel (A)
Input Sel (B)
Input Sel (C)
Input Sel (D)
AVR Volume +
AVR Volume –
AVR Mute
Page Up
Page Down
Previous
Pause
Next
Rew 77
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
43
44
45
Channel/Page Up Channel/Preset Up
Channel/Page Down Channel/Preset Down
Preset Up
Preset Down
Preset Up
Preset Down
Preset Up
Preset Down
46
47
48
49
50
51
52
53
54
55
56
57
58
Previous
Pause
Next
Rew 77
Play 3
FF 33
Record
Stop
AVR Settings
Info Settings
Source Settings
Sleep
Previous
Pause
Next Step
Rew 77
Play 3
FF 33
Record
Stop
AVR Settings
Info Settings
Setup
Sleep
Zone Select
Play 3
FF 33
FF 33
Stop
AVR Settings
Info Settings
Setup
Sleep
Zone Select
Stop
AVR Settings
Info Settings
AVR Settings
Info Settings
AVR Settings
Info Settings
AVR Settings
Info Settings
AVR Settings
Info Settings
AVR Settings
Info Settings
TV/VCR
Sleep
Zone Select
Sleep
Zone Select
Sleep
Zone Select
Sleep
Zone Select
Sleep
Zone Select
Sleep
Zone Select
Zone Select
65
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A14 – continued
AUX
PVR
No. Button Name
Cable/SAT
Game
CD
HDTV
TiVo
VCR
USB
Network
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
AVR Power On
AVR Power Off
Device Power On
Device Power Off
Cable/SAT
DVD
The Bridge
USB
Radio
TV
Game
Media Server
AUX
Network
Audio Effects
Video Modes
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
AVR Power On
AVR Power Off
Play
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
AVR Power On
AVR Power Off
Power On
Power Off
Input Sel
Input Sel
Input Sel
USB
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
AVR Power On
AVR Power Off
AVR Power O
AVR Power Off
Stop
Input Sel
Input Sel
Input Sel
USB
Input Sel
Input Sel
Input Sel
USB
Input Sel
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Input Sel
Input Sel
Input Sel
USB
Input Sel
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Radio
Radio
Radio
Radio
Radio
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Surround Modes
1
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Surround Modes
1
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Surround Modes
1
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Surround Modes
1
Input Sel
Input Sel
Input Sel
Input Sel
Network
Audio Effects
Video Modes
Surround Modes
1
Surround Modes
Surround Modes
Surround Modes
Surround Modes
Surround Modes
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
Last
0
Activity
Back/Exit
Menu
Up
Left
OK
Right
Light
Down
Disc Menu
Red
Green
Yellow
Blue
Volume +
Volume –
Mute
Prev. Ch
0
Activity
Bypass
Menu
Up
Left
OK
Right
Light
Down
OSD
Guide
PPV
Fav. Ch
Music
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
Enter
0
Activity
Clear
Start
Up
Left
Select
Right
Light
Prev. Ch
0
Activity
Exit/Cancel
Menu
Up
Left
Enter
Right
Instant Replay
0
Activity
Exit
Menu
Up
Left
Setup
Right
Light
Enter/Last
0
Activity
Exit
Menu
Up
Left
Select
Right
Light
Down
TiVo
Window
Live TV
Slow
Last
0
Activity
Back/Exit
Menu
Up
Left
OK
Right
Light
Down
Last
0
Activity
Back/Exit
Menu
Up
Left
OK
Right
Light
Down
0
0
Activity
Activity
Cancel
Menu
Up
Left
Enter
Right
Light
Down
OSD
Light
Light
Down
OSD
Down
DVD Menu
•
Down
AV
Mark
Open/Close
Random Play
Repeat
Intro Scan
AVR Volume +
AVR Volume –
AVR Mute
(+10)
Disc Skip
Skip Down
Pause
Skip Up
R. Search
Play 3
Caption
Fav. Ch
MTS
Aspect
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
Back
Input Sel (A)
Input Sel (B)
Input Sel (C)
Input Sel (D)
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
Previous
Input Sel (A)
Input Sel (B)
Input Sel (C)
Input Sel (D)
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
Previous
I
Repeat
Jump Up
Jump Down
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
Last Clip
Pause
Next Clip
Rew 77
Play 3
FF 33
Record
Stop
L
X
Skip
AVR Volume +
AVR Volume –
AVR Mute
Scan Up
Scan Down
Slow Down
Pause
Slow Up
Prev.
Play 3
Next
Subtitle
Stop
AVR Settings
Info Settings
Program
Sleep
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
Thumb Down
Pause
Thumb Up
Rew 77
Play 3
FF 33
Record
Stop
AVR Settings
Info Settings
TV Input
Sleep
AVR Volume +
AVR Volume –
AVR Mute
Channel Up
Channel Down
Scan Down
Pause
Scan Up
Rew 77
Play 3
FF 33
Record
Stop
AVR Settings
Info Settings
TV/VCR
43
44
45
Channel/Page Up
Channel/Page Down
Previous
Pause
46
47
48
49
50
51
52
53
54
55
56
57
58
Pause
Pause
Next
Rew 77
Play 3
Pause
Next
Rew 77
Play 3
Next
Replay
Rew 77
Play 3
FF 33
Record
Stop
AVR Settings
Info Settings
TV/VCR
Sleep
Rew 77
Play 3
FF33
Record
Stop
AVR Settings
Info Settings
Source Settings
Sleep
F. Search
Time
Stop
AVR Settings
Info Settings
FF 33
FF 33
Stop
AVR Settings
Info Settings
Stop
AVR Settings
Info Settings
AVR Settings
Info Settings
TV/CATV
AVR Settings
Info Settings
TV/DVR
Sleep
Sleep
Sleep
Sleep
Sleep
Zone Select
Sleep
Zone Select
Zone Select
66
Download from Www.Somanuals.com. All Manuals Search And Download.
AVR 7550HD TECHNICAL SPECIFICATIONS
Audio Section
Video Section
Television Format
Stereo Mode, Continuous Average Power (FTC)
100 Watts per channel, 20Hz–20kHz, @ <0.07%
THD, both channels driven into 8 ohms
NTSC
1Vp-p/75 ohms
1Vp-p/75 ohms
Input Level/Impedance
Output Level/Impedance
Video Frequency Response
(Composite and S-Video)
Seven-Channel Surround Modes
Power per Individual Channel
10Hz–8MHz (–3dB)
Video Frequency Response
(Component Video)
HDMI™
Front L & R channels:
85 Watts per channel
@ <0.07% THD, 20Hz–20kHz into 8 ohms
10Hz–100MHz (–3dB)
Version 1.3a with 10-bit Deep Color
General
Center channel:
85 Watts @ <0.07% THD, 20Hz–20kHz into 8 ohms
Power Requirement
Power Consumption
AC 120V/60Hz
120W idle, 1405W maximum
(7 channels driven)
Surround (L & R Side, L & R Back) channels:
85 Watts per channel
@ <0.07% THD, 20Hz–20kHz into 8 ohms
Dimensions
Width
Height
(Product)
17-5/16 inches (440mm) 20-1/2 inches (520mm)
6-1/2 inches (165mm) 11 inches (280mm)
17-1/16 inches (435mm) 22-13/16 inches (580mm)
(Shipping)
Input Sensitivity/Impedance
Linear (High-Level)
200mV/47k ohms
100dB
Depth
Signal-to-Noise Ratio (IHF-A)
(Product)
(Shipping)
Surround System Adjacent Channel Separation
Weight
44 lb (20kg)
51 lb (23.3kg)
Pro Logic® I/II
Dolby® Digital (AC-3)
DTS®
40dB
55dB
55dB
Depth measurement includes knobs, buttons and terminal connections.
Height measurement includes feet and chassis.
Features, specifications and appearance are subject to change without notice.
Frequency Response
@ 1W (+0dB, –3dB)
Harman Kardon and Logic 7 are trademarks of Harman International Industries, Incorporated,
registered in the United States and/or other countries. EzSet/EQ, Designed to Entertain and
The Bridge II logo are trademarks of Harman International Industries, Incorporated.
10Hz –130kHz
60 Amps
High Instantaneous
Current Capability (HCC)
Apple, iPod, iTunes and Macintosh are trademarks of Apple Inc., registered in the U.S. and other
countries. iPod not included. “Made for iPod” means that an electronic accessory has been designed
to connect specifically to iPod and has been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its compliance with safety
and regulatory standards.
Transient Intermodulation
Distortion (TIM)
Unmeasurable
40V/µsec
Slew Rate
A-BUS is a registered trademark of Leisure Tech Electronics Pty Ltd.
Audiovox is a registered trademark of Audiovox Corporation.
Blu-ray Disc is a trademark of the Blu-ray Disc Association.
CEA is a registered trademark of the Consumer Electronics Association.
FM Tuner Section
Frequency Range
Usable Sensitivity
Signal-to-Noise Ratio
Distortion
87.5–108.0MHz
IHF 1.3µV/13.2dBf
Mono/Stereo 70/68dB
Mono/Stereo 0.2/0.3%
40dB @ 1kHz
400kHz, 70dB
80dB
Manufactured under license from Dolby Laboratories. Dolby, the double-D symbol and Pro Logic
are registered trademarks of Dolby Laboratories. MLP Lossless is a trademark of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,003,467 and other U.S. and worldwide patents issued and pending.
DTS, DTS-ES and DTS Neo:6 are registered trademarks, and DTS 96/24, DTS-HD, DTS-HD High
Resolution Audio and DTS-HD Master Audio are trademarks, of DTS, Inc. © 1996-2007 DTS, Inc.
All Rights Reserved.
Stereo Separation
Selectivity
Image Rejection
IF Rejection
90dB
EyeConnect is a trademark of Elgato Systems.
AM Tuner Section
Frequency Range
Signal-to-Noise Ratio
Usable Sensitivity
Distortion
Faroudja DCDi Cinema is a trademark of Genesis Microchip Inc.
HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC).
520–1720kHz
45dB
Loop 500µV
1kHz, 50% Mod 0.8%
10kHz, 30dB
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
Intel is a trademark of Intel Corporation in the U.S. and other countries.
SACD is a trademark of Sony Corporation.
Selectivity
TiVo is a registered trademark of TiVo Inc.
Windows Media is a registered trademark of Microsoft Corporation in the United States and/or
other countries.
XM, SIRIUS and all related marks and logos are trademarks of Sirius XM Radio Inc. and its sub-
sidiaries. All other marks and logos are the property of their respective owners. All rights reserved.
XM subscription sold separately. Taxes and a one-time activation fee may apply. XM tuner and home
dock required (each sold separately) to receive the XM service. All programming and fees subject
to change. It is prohibited to copy, decompile, disassemble, reverse engineer, hack, manipulate or
otherwise make available any technology or software incorporated in receivers compatible with the
XM Satellite Radio System. Service not available in Alaska or Hawaii.
You’ll need the product’s serial number. At the same time, you can
choose to be notified about new products and/or special promotions.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
8500 Balboa Blvd., Northridge, CA 91329
© 2009 Harman International Industries, Incorporated.
All rights reserved.
Part No. CQX1A1308Z
Download from Www.Somanuals.com. All Manuals Search And Download.
|