•PT2500(g).qx 10/23/96 7:36 AM Page 16
Harman Kardon
PT2500
A/VSurround Tuner Controller
Volume
Tuning
1
6
2
7
3
8
4
9
5
AM
FM
DIRECT
CENTER
MEMORY
MHz
Tuned
FMST
PRESET
Scan
DOLBY 3-CH
THEATER
STADIUM
Loudness
FM
MS
MIN
MODE
NORM
WIDE
DELAY
TIME
SLEEP
AM
KHz
FM Mode
Auto/Man
0
PHANTOM
TAPE2MON
AUTO VCR1REC
SOURCE VDP VCR2
0-30
Memory
Off Pro-Logic Stadium Test
Tape 1 VCR 1 VCR 2 Tuner
CD
Bass
Treble
Balance
VCR 2
VCR 2
Sel
Direct
Power
Delay
3 Ch
Theater Center
Tape2Mon Rec
VDP
TV/Aux Phono
Owner’s Manual
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 2
Introduction and Safety Information
1
Congratulations! With the purchase
of a Harman Kardon PT2500 you are
about to begin many years of listening
enjoyment. The PT2500 has been custom
designed to provide all the excitement
and detail of movie soundtracks and
Five audio inputs, three audio/video
inputs and the PT2500’s 30 preset tuner
enable it to serve as the control center for
a complete audio/video system. A system
remote control operates the PT2500 and
compatible Harman Kardon source
create a safety and fire hazard, and may
damage the amplifier.
If you have any questions about the volt-
age requirements for your specific model,
or about the line voltage in your area,
contact your dealer before plugging the
unit into a wall outlet.
every subtle nuance of musical selections. equipment, while an on board trigger
jack provides control capability to auto-
While complex processing systems are
hard at work within the PT2500, hook-
up and operation are simple. Color keyed
connections, a comprehensive remote
control and on screen menus make the
PT2500 easy to use. To obtain the maxi-
mum enjoyment from your new receiver
we urge you to take a few minutes to read
through this manual. This will ensure
that connections to speakers, source
playback units and other external devices
are made properly. A few minutes spent
learning the functions of the various
controls will enable you to take advan-
tage of all the power the PT2500 is able
to deliver.
matically turn on the companion
PA5800 amplifier.
Do Not Use Extension Cords
To avoid safety hazards, use only the
power cord supplied with your unit. If a
replacement cord is used, make certain
that it is of similar gauge. We do not rec-
ommend that extension cords be used
with this product. As with all electrical
devices, do not run power cords under
rugs or carpets or place heavy objects on
them. Damaged power cords should be
replaced immediately with cords meeting
factory specifications.
Features
■
■
Analog Devices decoding circuit for
precise surround decoding
Dolby* ProLogic*, Dolby 3 Stereo,
Theater and Stadium surround modes
■
■
■
Direct Mode for pure stereo playback
System remote control
Remote Trigger Control for PA5800
Important Safety Information
Handle the AC Power Cord Gently
When disconnecting the power cord from
an AC outlet, always pull the plug, never
pull the cord. If you do not intend to use
the amplifier for any considerable length
of time, disconnect the plug from the AC
outlet.
Verify Line Voltage Before Use
Your PT2500 has been designed for use
in North America with 120 volt AC cur-
rent. Connection to a line voltage other
than that for which it is intended can
If you have any questions about this
product, its installation or operation,
please contact your dealer. They are your
best local source of local information.
You may also contact Harman Kardon
directly via the Internet at
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
Description and Features
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The PT2500 is a full featured A/V sur-
round tuner controller, incorporating
a wide variety of listening options.
Through the use of an Analog Devices
decoder, surround encoded programs are
played back with stunning accuracy,
while the direct mode enables stereo
recordings to be played back in their
purest form. The open architecture of a
surround tuner controller allows for easy
expansion to full discrete surround
decoding with external adapters.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE THE
GROUNDING PLUG ON THE POWER CORD, OR USE ANY PLUG OR
EXTENSION CORD THAT DOES NOT HAVE A GROUNDING PLUG PROVIDED.
MAKE CERTAIN THAT THE AC OUTLET IS PROPERLY GROUNDED.
DO NOT USE AN ADAPTER PLUG WITH THIS PRODUCT.
*Trademarks of Dolby Laboratories
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 3
Introduction and Safety Information
2
■
Do Not Open The Cabinet
Make certain that proper space is pro-
vided both above and below the unit
for ventilation. If this product will be
installed in a cabinet or other
enclosed area, make certain that there
is sufficient air movement within the
cabinet. Under some circumstances a
fan may be required.
against harmful interference in a resi-
dential installation. This equipment gen-
erates, uses and can radiate radio
There are no user serviceable compo-
nents inside this product. Opening the
cabinet may present a shock hazard, and
any modification to the product will void
your guarantee. If water or any metal
object such as a paper clip, wire or a sta-
ple accidentally falls inside the unit, dis-
connect it from the AC power source
immediately, and consult an authorized
service center.
frequency energy and, if not installed
and used in accordance with the instruc-
tions, may cause harmful interference to
radio communication. However, there is
no guarantee that harmful interference
will not occur in a particular installa-
tion. If this equipment does cause harm-
ful interference to radio or television
reception, which can be determined by
tuning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the follow-
ing measures:
■
■
Do not place the unit directly on a
carpeted surface.
Avoid installation in extremely hot or
cold locations, or an area that is
exposed to direct sunlight or heating
equipment.
CATV or Antenna Grounding
If an outside antenna or cable system is
connected to this product, be certain that
it is grounded so as to provide some pro-
tection against voltage surges and static
charges. Section 810-B of the National
Electrical Code, ANSI/NFPA No. 70-1996,
provides information with respect to prop-
er grounding of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of
grounding conductors, location of anten-
na discharge unit, connection to ground-
ing electrodes and requirements of the
grounding electrode.
■
■
Avoid moist or humid locations.
■
Reorient or relocate the receiving
Do not obstruct the ventilation slots
on the top of the unit, or place objects
directly over them.
antenna.
■
Increase the separation between the
equipment and receiver.
Cleaning
■
Connect the equipment into an outlet
When the unit gets dirty, wipe it with a
clean, soft dry cloth. If necessary, wipe it
with a soft cloth dampened with mild
soapy water, then a fresh cloth with clean
water. Wipe dry immediately with a dry
cloth. NEVER use benzene, thinner, alco-
hol or any other volatile cleaning agent.
Do not use abrasive cleaners, as they may
damage the finish of metal parts. Avoid
spraying insecticide near the unit.
on a circuit different from that to
which the receiver is connected.
■
Consult the dealer or an experienced
radio/TV technician for help.
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the
CATV (Cable TV) system installer’s atten-
tion to article 820-40 of the NEC that
provides guidelines for proper grounding
and, in particular, specifies that the cable
ground shall be connected to the ground-
ing system of the building, as close to the
point of cable entry as possible.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept interference
received, including interference that may
cause undesired operation.
Moving The Unit
Before moving the unit, be certain to dis-
connect any interconnection cords with
other components, and make certain
that you disconnect the unit from the AC
outlet.
Note: Changes or modifications may
cause this unit to fail to comply with Part
15 of the FCC Rules and may void the
user’s authority to operate the equip-
ment.
Installation Location
■
To assure proper operation, and to
avoid the potential for safety hazards,
place the unit on a firm and level sur-
face. When placing the unit on a
shelf, be certain that the shelf and any
mounting hardware can support the
weight of the product.
Important information for the user
Note: This equipment has been tested
and found to comply within the limits for
a Class B digital device, pursuant to Part
15 of the FCC Rules. The limits are
designed to provide reasonable protection
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 4
Introduction and Safety Information
3
When positioning your PT2500 in its
final location, make certain that any
shelf or stand is capable of supporting it’s
weight, and that there is adequate venti-
lation on all sides, as well as on the top
and bottom. Do not place CDs, record
jackets, owner’s manuals, or other paper
on top of, or beneath the unit. This will
block air flow, causing degraded perfor-
mance and a possible fire hazard. If the
unit is to be enclosed in a cabinet or
rack, make certain that there is adequate
air circulation, with a means provided
for hot air to exit, and for cool air to be
brought in.
Unpacking and Installation
Using this Manual
The carton and shipping materials used
to protect your new PT2500 during ship-
ment were specially designed to cushion
it from shock and vibration. We suggest
that you save the carton and packing
materials for use in shipping if you move
or should the unit ever need repair.
For easy identification of the inputs, out-
puts and controls on the PT2500, a sepa-
rate reference card accompanies this
manual. Printed on that card are dia-
grams of the front and rear panels and
the remote control. Refer to that card as
needed to make certain that connections
are being made properly.
To minimize the size of the carton in
storage, you may wish to flatten it. This
is done by carefully removing any staples
that attach the carton flaps to one anoth-
er, and then slitting the tape covering the
seams. Fold the carton down to a more
two dimensional appearance. Packing
materials that cannot be collapsed
should be saved along with the carton in
a plastic bag.
The following conventions are used
throughout this manual when referring
to the diagrams on the reference card:
1: A number within a square references
a front panel control.
¡: A number within a circle references
a connection point on the rear panel.
: A number within an oval references
a
a button on the remote control.
If you do not wish to save the packaging
materials, please note that the carton
and other sections of the shipping protec-
tion are recyclable. Please respect the
environment and discard those materials
at a local recycling center.
Example: Bold type will be used to indi-
cate a front or rear panel control. It will
typically be followed with a reference let-
ter or number to the specific control
being described.
EXAMPLE: OCR type indicates a mes-
sage that is visible through the display
window.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 5
Front Panel Controls
4
Ó Up/Down Tuning Button: Press
! Bass Control: Turn this control to
adjust the low frequency output of
the left/right channels by as much as
±10dB. Set this control to a suitable
position for your taste and room
acoustics.
Using the Reference Card supplied with
this manual, familiarize yourself with
each of the controls on the front panel of
the PT2500. This section of the Manual
will also serve as a quick reference to the
operation of any of these controls.
¤
the left side
lower frequency stations and the
of the button to tune
⁄
right side
of the button to tune
higher frequency stations. When a
station with a strong frequency is
tuned, the TUNED indicator will illu-
minate in the Information Display.
@ Treble Control: Turn this control
to adjust the high frequency output
of the left/right channels by as much
as ±10dB. Set this control to a suit-
able position for your taste and room
acoustics.
Ô FM Mode: Press this button to
select the stereo or mono mode for
FM tuning. In the STEREO mode an
FMST indicator will illuminate in the
information display, and stereo
reception will be provided when sta-
tions are transmitting stereo signals.
In the MONO mode the left and right
signals from stereo broadcasts will
be mixed together and reproduced
through all channels. Select the
MONO mode fro better reception of
weak signals.
1 Power Switch: Press this button
to turn the PT2500 on or off. In order
to use the power button on the
remote this power switch must be
pressed once and left in the “stand-
by” mode. Note that a green indica-
tor around the switch will illuminate
when the unit is on, and an orange
”standby” indicator will illuminate
when the unit has been turned off
using the remote control.
# Balance Control: Turn this con-
trol to change the relative volume for
the front left/right channels.
NOTE: For normal operation of the
surround modes this control should
be at the midpoint, or “12 O’clock”
position.
2 VCR2 Selector: Press this button
to select the front panel VCR2 inputs
rather than the rear panel inputs.
$ VCR2 Inputs: This alternate set
of VCR2 Inputs may be used for the
connection of a camcorder or video
game. Select this input by pressing
the VCR2 button 2 on the front
panel.
Information Display: The indica-
tors in this display illuminate to pro-
vide visual display of the unit’s
operation.
3 Direct Input Selector: Press this
button to select direct input to the
preamp circuits, bypassing all tone
controls and surround processing.
When this feature is activated, the
DIRECT indicator illuminates with-
in the information display.
Ò Remote Sensor: This sensor
receives the signals from the remote
control to operate the unit. Do not
block this area.
% Loudness Button: Press this
button when listening at low levels to
activate special circuits that com-
pensate for the response of the
human ear at lower volumes. In the
off position the unit will provide flat
frequency response.
Ú Tuner Memory Button: Press
this button to store an AM or FM fre-
quency in the unit’s memory. The
MEMORY indicator will flash in the
display to remind you to choose a
numeric location using Numeric
Buttons on the front panel or remote
(Ùd). Press this button a second
time to complete the memorization
process. Storing a station in a mem-
ory location that has already been
used will overwrite the existing data.
4 Delay Time Adjust: Press this
button to adjust the delay time
between the front and rear channels.
5 Surround Off: Press this button
to select conventional two channel
stereo reproduction and to cancel
surround processing.
^ Volume Control: Rotate this
control to raise or lower the volume.
Note that this is a motorized control,
and when the volume is changed
using the remote control n it will
move in response to remote
commands.
6 Surround Mode Selectors:
Press one of these buttons to select
a surround processing mode.
& Mute/Volume Indicator: In nor-
mal operation this green LED pro-
vides a relative indication of the
unit’s volume level. When the
PT2500 is in the MUTE mode, this
indicator flashes to remind you that
output to the speakers has momen-
tarily been silenced.
7 Center Channel Mode Selector:
Press this button to change the cen-
ter channel mode.
NOTE: The preset memories are pro-
tected from power loss for two
weeks. If the unit is unplugged for
more than two weeks all stored fre-
quencies will be erased.
8 Test Mode Selector: Press this
button to place the unit in the Test
mode for adjustment of system out-
put levels.
Û Preset Scan Button: Press this
button to scan the stations entered
in the unit’s memory. When the
desired station is reached, press
the button again to stop the scan.
9 Tape 2 Monitor: Press this button
to monitor the output of the tape
deck connected to the Tape 2
Inputs. For normal operation this
control should be in the off position.
* Auto/Man Selector: Press this
button to select AUTO or MANUAL
tuning. In the AUTO mode the tuner
will stop only at stations with a strong
signal. In the MANUAL mode the
tuner will step in 50kHz increments
for FM and 10kHz increments for AM.
Ù Numeric Buttons: Use these
buttons to enter or recall stations
from the tuner memory.
) Input Selectors: Press one of
these buttons to select an input
source.
( AM/FM Selector: Press this
button to select AM or FM stations.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 6
Rear Panel Connections
5
¤ VDP A/V Inputs: Connect the
audio and video outputs of a laser
disc or DVD player to these jacks.
b Center Channel Outputs:
Connect the output of one of these
jacks to the center channel input of
a power amplifier or digital audio
processor with pass through capa-
bility.
Using the Reference Card supplied with
this manual, use this section as a quick
guide to the connections required to
install the PT2500. For complete instal-
lation and set up instructions, see pages
7-10.
‹ Video Monitor Outputs:
Connect these jacks to the video
input of a TV or video projector.
NOTE: In most applications only one
center channel connection will be
required. The output of both jacks is
identical, and either jack may be
used for system connections.
› Remote Amplifier Trigger:
Using the accessory cable supplied
with the PT2500, connect this jack to
compatible products such as the
PA5800 for automatic turn on/off
operation.
¡ Phono Input: Connect the output
of a turntable or tone arm to these
jacks.
™ System Ground Terminal: To
reduce hum and noise, connect the
ground lead from your turntable or
tone arm to this terminal.
c Front Channel Outputs:
Connect these jacks to the front
left/right channel inputs of a power
amplifier or digital audio processor
with pass through capability.
fi AC Power Cord: Connect this
plug to an unswitched, wall mounted
AC outlet.
£ Aux Input: Connect the outputs
of any audio source to these jacks.
d Subwoofer Outputs: Connect
these jacks to the line level input of a
powered subwoofer, or to the inputs
of a subwoofer amplifier.
fl Unswitched Accessory AC
Power Outlet: This outlet provides
AC power that may used with any AC
device up to 100 watts. The power
will remain on at this outlet regardless
of whether the PT2500 is on or off.
¢ CD Input: Connect the outputs of
a CD player or external D/A convert-
er to these jacks.
NOTE: This output is a full range
left/right signal. For proper operation
BOTH jacks must be connected to
the left/right inputs of a powered
subwoofer, or a “Y” cable must be
used to connect the two outputs
together if a single input mono sub-
woofer is used.
∞ Tape 1 Input: Connect the
PLAY/OUT jacks of an audio tape
recorder to these jacks.
‡ Switched Accessory AC Power
Outlet: This outlet provides AC
power to connected products only
when the PT2500 is turned on. Note
that the total current draw of the
products may not exceed 100 watts.
§ Tape 1 Output: Connect the
RECORD/INPUT jacks of an audio
tape recorder to these jacks.
¶ Tape 2 Input: Connect the
PLAY/OUT jacks of a second audio
tape recorder to these jacks.
WARNING: Since this is a full range
output, the signal must be sent
through a crossover or low pass filter
before being used with a passive
subwoofer or other speaker that
does not contain a built in crossover.
° Remote Control Extension
Output: This jack may be connect-
ed to other compatible Harman
Kardon products so that they will
receive infrared commands cap-
tured by the PT2500’s remote sen-
sor.
• Tape 2 Monitor Output: Connect
the RECORD/INPUT jacks of a sec-
ond audio tape recorder to these
jacks.
e AM Antenna Input: Connect the
AM loop antenna supplied with the
PT2500 to these terminals. An exter-
nal AM antenna may also be con-
nected here.
· Remote Control Extension Input:
If the PT2500’s front panel IR sensor
is blocked due to cabinet doors or
other obstructions, an external IR
sensor may be used. Connect the
output of the sensor to this jack.
ª VCR1 A/V Inputs: Connect the
audio and video PLAY/OUT jacks of
a VCR to these jacks.
‚ VCR1 A/V Outputs: Connect the
audio and video record RECORD/IN
jacks of a VCR to these jacks.
f FM Antenna Input: Connect an
FM antenna to these terminals. Note
that a 300 ohm to 75 ohm adapter is
required for connections from twin
lead dipole antennas.
a Surround Channel Outputs:
Connect these jacks to the surround
channel inputs of a power amplifier
or digital audio processor with pass
through capability.
⁄ VCR2 A/V Inputs: Connect the
audio and video PLAY/OUT jacks of
a second VCR, or another A/V
source such as a satellite receiver to
these jacks.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 7
System Remote Control
6
f Input Select Buttons: Press
one of these buttons to choose an
input source.
m Mute Button: Press this button to
momentarily silence the speakers.
Note that the Mute/Volume Indicator
& will flash to remind you that the
Mute function is engaged. Press the
button again to return to the previ-
ously selected listening level.
Using the Reference Card supplied with
this manual, familiarize yourself with
each of the controls on the PT2500’s
infrared remote control. This section of
the manual will also serve as a quick ref-
erence to the operation of any of these
controls.
Note: Automatic Power On: When
you press any Input Select Button
while the unit is in the Standby
Mode, the system will automatically
be turned on.
n Master Volume Control: Press
this button to raise or lower the over-
all system volume to all speakers.
g Delay Time Adjust: Press this
button to adjust the amount of delay
between the sounds heard from
the front and surround speakers.
This function is only available in
the Dolby ProLogic, Theater and
Stadium modes.
a Transmitter Window: An
infrared beam is transmitted from
this window when you press any but-
ton on the remote. For the remote to
function properly always point this
window toward the remote sensor on
the PT2500 and do not obstruct this
window.
o Center Mode Select: Press
this button to select the center
channel mode. Each press of the
button changes the mode in the
following sequence:
Normal‡ Wide‡ Phantom
h Surround Mode Selectors:
Press one of these buttons to
choose a surround processing
mode. Press the OFF button to
cancel the surround processing for
conventional stereo reproduction.
p Test Mode Select: Press this
button to have a test signal noise
appear in sequence through the left,
center, right and surround speakers
so that relative volume may be
adjusted.
i Center Level Up/Down
Buttons: These buttons adjust the
center channel volume relative to
that of the other speakers. They
operate only in the Dolby ProLogic
and Dolby 3 Stereo modes.
q Cassette Deck Controls: These
buttons control the functions of com-
patible Harman Kardon cassette
decks.
Remote Control
Operation Range
r Preset Scan Button: Press this
button to scan the stations entered
in the unit’s memory. When the
desired station is reached, press the
button again to stop the scan.
j Rear Level Up/Down Buttons:
These buttons adjust the volume of
the rear (Surround) channels relative
to that of the other speakers. They
operate only in the Dolby ProLogic,
Theater and Stadium modes.
b Power Button: Press this button
to turn the PT2500 on or off.
s Battery Compartment: Install
two “AA” batteries as shown to
power the remote control.
NOTE: In order for this button to
work, the PT2500 must first be
placed in the standby mode by
pressing the front panel Power
switch 1 until it is engaged and the
ring surrounding the switch turns
amber.
k Display Dim: Press this button
to dim the brightness of the front
panel display. A second press turns
that display off completely and a
third press returns the displays to
their normal brightness level.
c Up/Down Tuning Buttons:
Press these buttons to manually tune
higher or lower frequency stations.
l Sleep Timer Button: Press this
button to activate the sleep timer.
Each press increases the amount of
time before the unit will turn off, in
the following sequence:
d Numeric Buttons: Press these
buttons to select one of the stations
stored in the unit’s memory.
Slide the cover on the battery compart-
ment as shown to remove. Insert the
batteries being certain to observe proper
polarity.
10
20
30
60
90
OFF
min
min
min
min
min
e CD Function Controls: These
buttons will control the functions of a
compatible Harman Kardon CD
player or multi disc changer.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 8
Installation & Configuration
7
Your new Harman Kardon receiver is
designed to provide the best reproduction
from both movies and musical programs. on most turntables to the System
If the phono input is used, connect the
small ground wire connection furnished
The rear panel accessory outlets on the
PT2500 may be used to power low cur-
rent devices such as CD payers or tape
decks. The SWITCHED Accessory
AC Power Outlets ‡ are activated
only when the PT2500 is turned on. The
UNSWITCHED Accessory AC
Power Outlets fl may be used with
VCRs, as the power to these outlets is live
as long as the PT2500 remains connect-
ed to an AC power source.
To assure that the unit operates to its
fullest capability, it is important that you
spend a few minutes to properly install
and configure all of the elements in your
new system. Some, or all of the following
steps will apply to your system, depend-
ing on the equipment in use. If you have
any questions concerning the installation
of this product consult your local dealer,
or contact the Harman Kardon web site
Ground Terminal ™ on the rear
panel. This will greatly reduce system
noise and hum.
Assemble the supplied AM loop antenna
as shown below and connect it to the AM
ANTENNA Terminals e.
AM LOOP ANTENNA SETTING
CAUTION: The total power load for all
products connected to the accessory out-
lets must not exceed 100 watts. Do not
use them for high current devices such as
power amplifiers.
System Component
Connections
LEG
Stand and place it on a shelf, or hang it on a wall.
IMPORTANT SAFETY NOTE: Many
products feature automatic turn on cir-
cuitry which may accidentally be activat-
ed when making connections. For your
safety and to prevent damage to speakers,
amplifiers and other components we
strongly recommend that all equipment
power be turned off, or that AC power
cords be unplugged when any system
connections are made or changed.
It may be necessary to rotate the antenna
or change its position to achieve the best
AM reception. Connect an FM antenna to
the FM Antenna Terminals. A 300
ohm to 75 ohm adapter may be required
for some antennae.
If the PT2500’s front panel remote sensor
Ò is blocked by cabinet doors you may
still operate the unit via remote control
with the use of an optional external
remote sensor. Connect the output of the
sensor to the rear panel REMOTE
CONTROL Extension Input ·.
This jack may also be used as the IR
input from compatible multiroom con-
trol systems. The sensor may be looped
to other components by connecting the
REMOTE CONTROL Extension
Output ° to the IR remote input jack
of other compatible components.
If a PA5800 or other compatible amplifi-
er will be used, connect the supplied
accessory cable to the Remote
Amplifier Trigger Jack › on the
PT2500. Connect the other end to the
appropriate jack on your amplifier.
Consult the amplifier manual for further
instructions.
Using high quality interconnect cables,
connect all source components to the
appropriate input jacks on the rear
panel. When connecting audio recorders
and VCRs it is important to make certain
that the PLAY/OUT jacks on the recorders
are connected to the PLAY jacks on the
PT2500, and that the RECORD/IN jacks
of the recorders are connected to the
REC jacks on the PT2500.
Amplifier Connections
IMPORTANT NOTE: Do not connect
amplifier trigger cables to the “IR
Remote Control” jacks on this or any
other equipment.
Since the PT2500 is a tuner/preamplifier,
it does not include any on board power
amplifiers. The final step in the installa-
tion process is to connect the unit to the
amplifiers for each channel. Using high
quality audio interconnect cables, con-
nect the FRONT, CENTER and
SURROUND Channel Outputs
cba to the appropriate input jacks
of a power amplifier.
If you are using the PT2500 to switch
video inputs, connect either MONITOR
output ‹ to a video input on your TV or
projector.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 9
Installation & Configuration
8
Center Front Speaker
Although there are two outputs for the
center channel, only one connection is
typically required. As the two outputs are
identical, either one may be used and the
other left open.
Once the center channel speaker is
installed, position the left and right front
speakers so that they are as far away
from one another as the center channel
speaker is from the preferred listening
position. Ideally, the front channel
speakers should be placed so that their
tweeters are no more than 24″ off center
from the tweeter in the center channel
No more
than 24"
Left Front
Speaker
Right Front
Speaker
Subwoofer connections are made using
the SUBWOOFER Outputs d. When
using a powered subwoofer, connect
BOTH the left and right output subwoofer speaker.
outputs to the respective left and right
A) Front Channel Speaker Installation
with Direct View TV Sets or Rear Screen
Projectors
line level inputs on your subwoofer. As
the PT2500 subwoofer outputs are full
range, it will be necessary to adjust the
crossover frequency to your requirements
Depending on the specifics of your room
TV or Projection Screen
Center Front
acoustics and the type of speakers in use,
imaging may be improved by moving the
front left and right speakers slightly for-
Left Front
Speaker
Right Front
Speaker
Speaker
on the subwoofer’s control panel. Consult ward of the center channel speaker. If
the subwoofer instructions or consult
your dealer for additional information.
possible, adjust all front loudspeakers so
that they are aimed at ear height when
you are seated in the listening position.
When using a single subwoofer and a
separate mono power amplifier the
PT2500 subwoofer outputs must be com-
bined using an optional “Y” adapter. If
there is no crossover in the subwoofer an
optional, external low pass filter or
crossover system must also be used.
Using these guidelines, you may find that
it takes some experimentation to find the
correct location for the front speakers in
your particular installation. Don’t be
afraid to move things around until the
system sounds correct. Optimize speaker
locations so that pans across the front of
the room sound smooth, and that sounds
from all speakers appear to arrive at the
listening position at the same time with-
out delay from the center speaker as
opposed to the left and right speakers.
Optional Rear Wall Mounting
When using the PT2500 with an external
5.1 digital audio decoder such as the
Harman Kardon ADP303, connect all
Channel Outputs abc to the
decoder’s inputs. Use an optional “Y”
adapter to combine the subwoofer out-
puts and connect the “Y” adapter to the
decoder’s subwoofer input. The outputs
of the digital audio decoder should then
be connected to your power amplifiers.
The distance between the left and right
speakers should be equal to the distance
from the seating position to the viewing
screen. You may also experiment with
placing the left and right speakers slightly
forward of the center speaker.
Surround speakers should be placed on
the side walls of the room, at or slightly
behind the listening position. The center
of the speaker should face into the room
with the speaker drivers pointing towards
the front and rear of the room. The
speakers should be located so that the
bottom of the cabinet is at least 24″
higher than the listeners’ ears when in
the desired area.
At least 6 inches from ceiling
Speaker Selection and Placement
Depending on the type of center channel
speaker in use and your viewing device,
place the center speaker directly above or
below your TV .
At least 2 feet
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 10
Installation & Configuration
9
8
If side wall mounting is not practical, the
speakers may be placed on a rear wall,
behind the listening position. Again, they
should be located so that the bottom of
the cabinet is at least 24″ higher than
the listeners’ ears. The speakers should
be no more than 6 feet behind the rear of
the seating area.
To calibrate your system, follow these
steps:
7. Press the Test Tone button again
to turn the test signal off. Your system is
now properly calibrated and further vol-
ume adjustment should be made using
n
1. Turn on the PT2500 and the compan-
ion power amplifier.
the Master Volume
buttons on
2. Select the Dolby ProLogic mode using
the Surround Mode 6 button on the
front panel.
the remote or the front panel Volume
Once the system is calibrat-
ed no other adjustments are necessary.
^
Control.
3. Place the front panel Balance #
control at its midpoint position, so that
the indicator is pointing straight up in
the 12 o’clock position. If the Balance
control is normally in another position
to compensate for speaker placement rel-
ative to your preferred listening position,
leave it in that spot.
Delay Setting
Subwoofers produce non-directional
sound, so they may be placed almost
anywhere in a room. Subwoofer place-
ment is highly influenced by room size
and shape, and the type of subwoofer
used. Follow the instructions of the sub-
woofer’s manufacturer, or experiment
with the best location for a subwoofer in
your listening room.
Delay time adjustment enables you to
adjust the timing between signals at the
front and surround channels.
The factory setting is appropriate for
most rooms, but in some instances the
use of an abundance of hard (reflective)
room surfaces such as windows and
wood floors, or soft (absorbent) surfaces
such as thick carpeting, acoustical tiles
and some furnishings may create an
unpleasant effect. These surfaces, in
conjunction with the size of the room,
the height of the ceiling and other
4. Sit in the location that you will nor-
mally occupy when using your PT2500.
Output Level Calibration
p8
5. Press the Test Tone
button
For proper operation in the surround
modes it is important that the level from
all channels be as close to one another as
possible. A small amount of time spent to
properly calibrate the PT2500’s output
levels will enable the unit to deliver all
the performance it is capable of within
the specific environment of your listen-
ing room.
on the remote or front panel and note
that a test noise signal will circulate
between the channels.
design aspects may cause the arrival of
surround channel sounds to become dis-
connected from rear channel sounds.
• While the test noise circulates among
the channels the word TEST and the
channel name will appear in the front
panel information display window. As the
names change you should first listen to
the location of the tone and verify that it
matches the name displayed in the dis-
play. If the display indicates a different
location than the speaker the test noise is
coming from you should turn off the
unit and verify that the connections to
the amplifier speakers are made to the
correct terminals on the rear panel.
To adjust delay time it is necessary to
select the ProLogic, Theater or Stadium
modes using the Surround Mode
Selector buttons on the front panel or
IMPORTANT NOTE: People are often
confused about the operation of the sur-
round channels. While some assume that
sound should always be coming from
each speaker, most of the time there will
be little or no sound in the rear channels.
This is because they are only used when a
movie director or sound mixer specifical-
ly places sound there to create an effect or
pull you into the action. When the output
levels have been properly set it is normal
for the rear speakers to operate only occa-
sionally. Artificially increasing the vol-
ume to the rear speakers will destroy the
illusion of an enveloping surround field
that duplicates the way you hear sound
in a movie theater or concert hall.
h6
remote
.
4
Press the Delay Adjust button on
the front panel to adjust the delay time
as observed in the Information
Display according to personal
preference or the following formula:
1. Measure the distance from the listen-
ing/viewing position to the front
speakers.
6. As the test signal circulates among the
channels, use the Center Level
o
j
Up/Down
and Rear Level
buttons on the remote to
Up/Down
2. Measure the distance from the listen-
ing/viewing position to the surround
speakers.
adjust the level so that the volume from
all channels sounds equal.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 11
Installation & Configuration
10
3. Subtract the distance to the rear/sur-
round speakers from the distance to the
front speakers and add 15. The resulting
number is the ideal delay time for your
room. For example, if the front speakers
are 10 feet away and the surround speak-
ers are 5 feet away, the formula will be
“10-5+15=20”. Thus, the correct delay
time in this room would be 20 ms.
CENTER
FRONT(left)
FRONT(right)
Note that the delay time for the Dolby
ProLogic Mode is adjusted in 2 ms incre-
ments from 16 ms. to 30 ms. The delay
setting for the Theater and Stadium
modes is adjusted in 8 ms increments
from 8ms to 96 ms.
REAR(right)
REAR(left)
Wide Mode: Select this mode if your
center channel speaker is a traditional
full range loudspeaker.
Center Channel Mode
FRONT(left)
FRONT(right)
The PT2500 permits you to tailor the
center channel output to match the type
of speakers used in your home theater.
o7
Press the Center Mode button
on the front panel or remote to select one
of the following. The center channel
mode is shown by indicators in the front
panel display window.
REAR(right)
REAR(left)
CENTER
FRONT(left)
FRONT(right)
Phantom Mode: Select this mode if a
center channel speaker is not used. The
PT2500 will create a “phantom” center
channel using the outputs of the left and
right speakers. Note that the Phantom
mode is not available when Dolby 3
Stereo is selected as a surround mode.
REAR(right)
REAR(left)
Normal Mode: Select this mode if your
center channel is small and has limited
bass response. Most specialized center
channel speakers fall into this category.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 12
Operation
11
4. Adjust the Center Channel Mode
7o and/or Delay Time 4g if a
change is required from the setting
established during installation.
names described above, select the
ProLogic mode using the front panel or
remote Surround Mode Selectors
6h.
OPERATION
1. Press the Power button 1 on the
front panel to turn the unit on.
• To use the remote for power on/off it is
necessary to turn the unit on from the
front panel switch and to leave the switch
in the “on” position. The PT2500 may
then be turned off using the Power but-
ton b on the remote. When the remote
is used to turn the unit “off” it is actually
placing the system in a standby mode, as
indicated by the amber color of the power
switch ring.
5. Adjust the volume to a comfortable
level using the front panel Volume
Control or remote Volume Up/Down
buttons ^n .
If a center channel speaker is used along
with front left/right speakers, but no sur-
round speakers are used, choose the
Dolby 3 Stereo mode6h. This
combines the surround signal into the
front left and right channels to create a
greater feeling of presence and a more
expansive sound field than with conven-
tional stereo signals. Center channel dia-
log information will continue to be
heard through its proper place at center
screen.
• To temporarily silence the system press
the Mute button m on the remote.
6. Adjust the Bass and Treble controls
!@ to suit your listening taste.
• If you will be away from home for an
extended period of time it is always a
good idea to completely turn the unit off
using the front panel Power button 1.
• To remove the tone controls from the
circuit, press the Direct button 3.
When listening to conventional stereo
recordings or programs, those with sepa-
rate left and right channels but no inten-
tionally recorded surround information,
you may wish to experiment with the
surround modes to see which produces
the effect you prefer. Stereo recordings
often contain sufficient natural phase
differences so that the ProLogic or
Dolby 3 Stereo Modes are enjoyable,
despite the lack of true surround infor-
mation.
• At lower volume levels you may wish to
engage the Loudness button % to
boost low and high frequency sounds to
compensate for response of the human
ear at low listing levels (known as the
Fletcher-Munson hearing curve).
2. Select the desired program source
using the Input Selector Switches
9)f on the front panel or remote.
• To use a camcorder or video game
which is connected to the front panel
VCR2 input, press the VCR2 Sel button
2.
Surround Mode Options
Surround sound processing enables four
separate audio signals to be transmitted
within the left and right channels of a
videocassette, radio or TV broadcast, or
video disc. Through a process known as
matrix encoding a separate center chan-
nel signal for dialog and a surround
channel for effects are encoded into the
stereo signal. When you see the Dolby
Surround™, Dolby Stereo™, DTS Stereo™
or other similar logos on a movie or
broadcast this indicates that the program
has surround information.
• When the selected input is VCR1, VCR2
or VDP the video signal for that input
will be routed to the MONITOR output
jacks ‹ and will be viewable on a TV
monitor connected to the PT2500. Make
certain that your TV set is set to the prop-
er “VIDEO” input to view the signal.
Stereo recordings may also sound more
expansive in either the Theater or
Stadium modes. Selecting these modes
6h uses the front left and right
speakers for normal stereo, while the sur-
round speakers are fed a reverberated
sound. In order to provide for a wider
variety of sound field effects, the sur-
round channel delay available in the
Theater and Stadium modes is substan-
tially greater than that in Dolby
3. Choose a surround mode using the
Surround Mode Selector 6h
buttons on the front panel or remote. To
listen to traditional two channel stereo
press the Surround Off button 5h.
When the program you are listening to
has encoded surround information, as
shown by one of the logos or brand
ProLogic.
NOTE: The center channel speaker is
not operational in the Theater or
Stadium modes.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 13
Operation
12
Preset Tuning
Tuner Operation
the P•Scan button again to stop the scan
Up to 30 stations may be stored in the
receiver’s memory for easy recall using
the front panel controls or the remote.
The PT2500’s built in tuner is capable of
tuning AM, FM or FM Stereo broadcast
stations. Stations may be tuned manually,
automatically or via presets.
at your desired station.
Sleep Timer
The PT2500 may be placed in a “Sleep
Mode” mode by pressing the Sleep
Timer l button on the remote.
To enter a station to the memory, first
tune to the station using the steps out-
lined above in the Manual Tuning
section. Then:
Manual Tuning
1. Press the Tuner button )f to
select the tuner as an input.
Each press of the button increases the
time until the unit shuts off in the fol-
lowing increments:
1. Press the Memory Ú button on
the front panel. Note that the MEM
indicator in the Information Display
window will illuminate and flash.
2. Select the AM or FM band using the
front panel AM/FM selector (.
10
min
20
min
30
min
60
min
90
min
OFF
⁄¤
3. Press the Tuning
Óc but-
The sleep time will be displayed at the
right side of the Information Display
while the timer is being programmed.
Once the amount of time entered has
elapsed, the PT2500 will automatically
go into the Standby mode, shutting off
all functions as well as the remote amp
trigger and the switched outlets.
ton to until the desired station is tuned.
Holding the button down will cause a
rapid advance through the frequency
band, tapping it lightly will advance
through bands one increment at a time.
The TUNEDindicator will illuminate
when a station is received with sufficient
strength for quality reception.
2. Within five seconds, press the
Numeric Buttons Ùd
corresponding to the memory location
where you wish to store this station’s
frequency.
• To enter a station to memory location
“30” press only the 0 button.
Tape Recording
3. Repeat the process after tuning to any
additional stations to be preset.
4. Press the FM Mode Ô button to
switch between mono and stereo recep-
tion. When a station’s signal is weak,
press the button until the FMSTindica-
tor in the information display goes
out. This will switch the tuner to mono,
but it may enable clearer reception.
In normal operation, the audio or video
source selected for listening through the
PT2500 is sent to the record outputs. This
means means that any program you are
watching or listening to may be recorded
simply by placing machines connected to
the outputs for TAPE1 § or VCR1 ‚
in the record mode.
Recalling Preset Stations
To select a station previously entered into
the preset memory press the Numeric
Buttons Ùd on the front panel or
the remote corresponding to the desired
station’s location. To select the station in
location “30”, press the 0 button only.
Auto Tuning
1. Press the Tuner button )f to
select the tuner as an input.
To dub an audio tape place the blank
tape in the machine connected to
Tape 2 and put it in the record mode.
Place the program tape in the machine
connected to Tape1 and put it in the
play mode. Select Tape 2 Mon as the
input source 9f to monitor the play-
back of the dub if the recorder has a
three head system.
• When you select a station using this
method the unit will automatically
switch to the tuner as its input.
2. Select the AM or FM band using the
front panel AM/FM selector (.
3. Press the Auto/Man * button.
Preset Station Scan
To automatically scan through the sta-
tions entered in the preset memory, press
the P•Scan r button on the remote.
The tuner will automatically begin to
search through the list of stations, stop-
ping for four seconds at each one. Press
4. Press the Tuning Óc button once
and tuning will start in the direction
indicated. The tuner will stop at the first
station with sufficient signal strength.
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 14
Troubleshooting
13
This unit is designed for trouble-free operation. Most problems users encounter are due to operating errors. So, if you have a problem,
first check this list for a possible solution. If the problem persists, consult your authorized Harman Kardon Service Center.
If the problem is...
Make sure that the...
No lights illuminate when POWER button is pressed
Unit is plugged into a live outlet
No sound is heard
Unit has been muted
Correct input function selector button has been pressed
Volume is turned up
Connections are properly made to the amplifier
Dolby Surround does not work on center and rear channels
Correct surround mode is selected
Rear and Center levels are turned up
You are using a surround encoded source
Selecting video component produces sound but no picture
The TV picture does not match the sound
Video cables are connected properly
Monitor output is connected to the video input on TV
Video sources are properly connected to receiver
Video/Antenna Switch on TV is set to Video
No output from one or more channels
Cables are not defective: Check/replace interconnect cables
The program source is operating and providing proper
signal output to the PA5800
No center channel output
Dolby surround or movie mode is turned on
Phantom mode is not active
Unit is in the ProLogic or Dolby 3 Stereo mode
Center channel level is properly adjusted
Tuner sound has a large amount of interference, or
The “Stereo” display is not illuminated, or
The antenna is properly connected
The antenna is properly located
Tuner sound distorts and/or volume level is too low
The antenna is set in the proper direction
The antenna is adequate to receive the desired station
Tuner is intermittent or continuously buzzing or hissing
Stations cannot be preset
The unit is away from fluorescent lights, TVs, motors and
other electrical appliances
After pressing the MEMORY button, the PRESET button is
pressed while the memory indicator blinks
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
•PT2500(g).qx 10/23/96 7:36 AM Page 15
Specifications
Preamplifier Section
Tuner Section: FM
Signal-to-Noise Ratio (ref. 1 Volt, A-Wtd)
Usable Sensitivity, Mono (dBf):
11.2
37.2
Phono (MM):
Video, CD:
74dB
92dB
50dB Quieting Sensitivity, Stereo (dBf):
Signal-to-Noise Ratio @65dBf, mono/stereo 74dB/70dB
Input Sensitivity/Impedance
Capture Ratio:
1.5dB
Phono (MM)
125pF
2.5mV/47kΩ,
150mV.22kΩ
Selectivity, Adjacent/Alternate Channel:
IF Rejection:
5dB/65dB
100dB
55dB
Video, CD, Tape
Phono Overload:
Am Rejection @45dBf:
Stereo Separation @1KHz, 65dBf:
THD @1KHz, 65dBf, mono/stereo (%)
45dB
RIAA EQ Accuracy (20Hz-20KHz):
Tone Control Range
Bass @100Hz:
±1.0dB
0.2/0.3
±10dB
±10dB
Tuner Section: AM
Sensitivity, External Antenna:
Treble @10KHz:
25µV
55dB
35dB
60dB
Loudness Contour @–40dB, 100Hz/10kHz: +6dB/+3dB
Alternate Channel Selectivity:
Image Rejection:
IF Rejection:
Dimensions (WxHxD)
inches:
17-3/8 x 6-1/8 x 16-1/2
440 x 155 x 420
17.1/7.8
mm:
Weight (lbs/kgs):
Depth measurement includes knobs, buttons and antennas.
Height measurement includes feet.
All features and specifications are subject to change without notice.
Manufactured under license from Dolby Laboratories Licensing Corporation.
Additionally licensed under one or more of the following patents: U.S. number 3,959,590,
Canadian numbers 1,004,603 and 1,037,877. “Dolby”, “ProLogic” and “TimeLink” are
registered trademarks of Dolby Loboratories Licensing Corporation.
Printed in Korea
Part #1111-PT2500
9007017884
PT2500 rev (G) 10/23/96
Download from Www.Somanuals.com. All Manuals Search And Download.
|