4.8 VOLT RECHARGEABLE
CORDLESS SCREWDRIVER
Model 95065
SET up AnD OpERATInG InSTRuCTIOnS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAnuAL.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 10d
Download from Www.Somanuals.com. All Manuals Search And Download.
6. When operating a power tool
outside, use an outdoor extension
cord marked “W-A” or “W”. These
extension cords are rated for outdoor
use, and reduce the risk of electric
shock.
Tool use and Care
1. use clamps (not included) or other
practical ways to secure and support
the workpiece to a stable platform.
Holding the work by hand or against
your body is unstable and may lead to
loss of control.
personal Safety
2. Do not force the tool. Use the correct
tool for your application. The correct
tool will do the job better and safer at
the rate for which it is designed.
1. Stay alert. Watch what you are
doing, and use common sense
when operating a power tool. Do not
use a power tool while tired or under
the influence of drugs, alcohol, or
medication. A moment of inattention
while operating power tools may result
in serious personal injury.
3. Do not use the power tool if the
Trigger Switch does not turn it on or
off. Any tool that cannot be controlled
with the Trigger Switch is dangerous
and must be replaced.
2. Dress properly. Do not wear loose
clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves
away from moving parts. Loose
clothes, jewelry, or long hair can be
caught in moving parts.
4. Disconnect the Charger Adapter from
the power source before making any
adjustments, changing accessories,
or storing the tool. Such preventive
safety measures reduce the risk of
starting the tool accidentally.
3. Avoid accidental starting. Be sure
the Power Switch is off before plugging
in. Carrying power tools with your
finger on the Power Switch, or plugging
in power tools with the Power Switch
on, invites accidents.
5. Store idle tools out of reach of
children and other untrained
persons. Tools are dangerous in the
hands of untrained users.
6. Maintain tools with care. Keep
cutting tools sharp and clean. Properly
maintained tools with a sharp cutting
edge are less likely to bind and
4. Remove adjusting keys or wrenches
before turning the power tool on. A
wrench or a key that is left attached to
a rotating part of the power tool may
result in personal injury.
are easier to control. Do not use a
damaged tool. Tag damaged tools “Do
not use” until repaired.
5. Do not overreach. Keep proper
footing and balance at all times. Proper
footing and balance enables better
control of the power tool in unexpected
situations.
7. Check for misalignment or binding of
moving parts, breakage of parts, and
any other condition that may affect
the tool’s operation. If damaged,
have the tool serviced before using.
Many accidents are caused by poorly
maintained tools.
6. use safety equipment. Always wear
eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing
protection must be used for appropriate
conditions.
8. use only accessories that are
recommended by the manufacturer
for your model. Accessories that may
be suitable for one tool may become
hazardous when used on another tool.
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 3
5. Include vibration-free periods each day
of work.
Service
1. Tool service must be performed by
qualified repair personnel. Service
performed by unqualified personnel
could result in a risk of injury.
6. Grip tool as lightly as possible (while
still keeping safe control of it). Let the
tool do the work.
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
2. When servicing a tool, use only
identical replacement parts. Follow
instructions in the “Inspection,
Maintenance, And Cleaning” section
of this manual. Use of unauthorized
parts or failure to follow maintenance
instructions may create a risk of electric
shock or injury.
SpECIFIC SAFETy RuLES
FOR THIS pRODuCT
1. Hold tool by insulated gripping
surfaces when performing an
operation as tool could come into
contact with hidden wiring. Contact
with a ”live” wire will make exposed
metal parts of the tool “live” and shock
the operator.
VIBRATIOn HAzARD
This tool vibrates during use.
Repeated or long-term exposure to vibration
may cause temporary or permanent physical
injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-
related injury:
2. Maintain labels and nameplates
on the Cordless Screwdriver. If
unreadable or missing, contact Harbor
Freight Tools for a replacement.
1. Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then have
regular medical check-ups to ensure
medical problems are not being caused
or worsened from use. Pregnant
3. Wear safety impact eye goggles
with side shields when using the
Cordless Screwdriver. Using personal
safety devices reduce the risk for injury.
Safety impact eye goggles with side
shields, and heavy work gloves are
available from Harbor Freight Tools.
women or people who have impaired
blood circulation to the hand, past hand
injuries, nervous system disorders,
diabetes, or Raynaud’s Disease
should not use this tool. If you feel any
medical or physical symptoms related to
vibration (such as tingling, numbness,
and white or blue fingers), seek medical
advice as soon as possible.
4. Maintain a safe working
environment. Keep the work area
well lit. Make sure there is adequate
surrounding workspace. Always keep
the work area free of obstructions,
grease, oil, trash, and other debris.
Do not use a power tool in areas near
flammable chemicals, dusts, and
vapors. Do not use this product in a
damp or wet location. Keep extension
cord away from water.
2. Do not smoke during use. Nicotine
reduces the blood supply to the hands
and fingers, increasing the risk of
vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
5. Avoid unintentional starting. Make
sure you are prepared to begin
work before turning on the Cordless
Screwdriver.
4. Use tools with the lowest vibration when
there is a choice between different
processes.
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
6. Do not force the Cordless
Screwdriver. This tool will do the work
better and safer at the capacity for
which it was designed.
Grounded Tools:
Tools with Three prong plugs
1. Tools marked with “Grounding
Required” have a three wire cord
7. unplug the Charger Adapter
from the Cordless Screwdriver
and the electrical outlet before
use or before performing any
inspection, maintenance, or cleaning
procedures.
and three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the tool should
electrically malfunction or break down,
grounding provides a low resistance
path to carry electricity away from the
user, reducing the risk of electric shock.
8. never leave the Cordless
Screwdriver unattended while
running. Turn power off if you have to
leave the Cordless Screwdriver.
2. The grounding prong in the plug is
connected through the green wire
inside the cord to the grounding system
in the tool. The green wire in the cord
must be the only wire connected to the
tool’s grounding system and must never
be attached to an electrically “live”
terminal.
9. people with pacemakers should
consult their physician(s) before
using this product. Electromagnetic
fields in close proximity to a heart
pacemaker could cause interference to
or failure of the pacemaker.
10. Connect the Charger Adapter to
a Ground Fault Circuit Interrupter
(GFCI) protected electrical outlet.
GROunDInG
Improperly
connecting the
grounding wire can result in
WARnInG
3-prong plug and Outlet
3. The tool must be plugged into an
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-prong
plug and Outlet.)
electric shock.
Check with a qualified
electrician if you are in doubt as
to whether the outlet is properly
grounded. Do not modify the
power cord plug provided with
the tool. never remove the
grounding prong from the plug.
Do not use the tool if the power
cord or plug is damaged. If
damaged, have it repaired by
a service facility before use. If
the plug will not fit the outlet,
have a proper outlet installed
by a qualified electrician.
Double Insulated Tools:
Tools with Two prong plugs
1. Tools marked “Double Insulated” do
not require grounding. They have a
special double insulation system which
satisfies OSHA requirements and
complies with the applicable standards
of Underwriters Laboratories, Inc., the
Canadian Standard Association, and
the National Electrical Code.
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 5
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by a
qualified electrician before using it.
8. Protect the extension cords from sharp
objects, excessive heat, and damp or
wet areas.
Outlets for 2-prong plug
RECOMMEnDED MInIMuM WIRE
GAuGE FOR EXTEnSIOn CORDS*
(120/240 VOLT)
2. Double insulated tools may be used in
either of the 120 volt outlets shown in
the preceding illustration. (See Outlets
for 2-prong plug.)
EXTEnSIOn CORD
nAMEpLATE
LEnGTH
AMpERES
(at full load)
Extension Cords
0 – 2.0
2.1 – 3.4
3.5 – 5.0
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three wire
extension cord.
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
2. As the distance from the supply outlet
increases, you must use a heavier
gauge extension cord. Using extension
cords with inadequately sized wire
causes a serious drop in voltage,
resulting in loss of power and possible
tool damage. (See Table A.)
* Based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
TABLE A
Symbology
Double Insulated
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See Table A.)
Canadian Standards
Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
V~
A
4. When using more than one extension
cord to make up the total length, make
sure each cord contains at least the
minimum wire size required. (See
Table A.)
No Load Revolutions per
Minute (RPM)
n xxxx/min.
0
5. If you are using one extension cord for
more than one tool, add the nameplate
amperes and use the sum to determine
the required minimum cord size. (See
Table A.)
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor use.
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 6
unpACKInG
When unpacking, make sure that all the parts are included. See Figure C below.
Figure C
Charger
Adapter
Screwdriver
Bits
Cordless
Screwdriver
If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual as soon as possible.
Battery precautions
1. To avoid accidents, never use a different charger adapter with this tool.
2. Do not expose this product to rain or wet conditions.
3. To avoid damage of cable and plug, never pull the cable to disconnect the Charger
Adapter.
4. Do not charge the Screwdriver if either the cable or plug are damaged.
5. Repairs should be carried out by a qualified service technician only.
6. Do not touch the battery poles with any conductive source.
note: The internal Battery Pack (22) does not come fully charged from the factory. Charge
before using.
REV 07a
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 7
CHARGInG THE BATTERy
1. Insert the Charger Adapter (24) cord plug into the unit connector as shown below.
2. Plug the Charger Adapter module into an electrical outlet. The red Charging Indicator
on the Cordless Screwdriver will light. Charge the new battery for 10 hours. When the
battery is fully charged all three LEDs will light up. Remove the Charger Adapter (24)
from the electrical outlet. The red Charging indicator will turn off. See Figure D.
Testing the Battery Charge
Figure D
Front Operation Light
Front Operation Light Switch
Charging Indicator LEDs
Charging Test Button
Charging Adapter Cord
Charging
Adapter (24)
Push the charging test button to display battery power. All three LEDs lit means the
battery is fully charged. Two LEDs lit indicate that the battery is half charged. One LED lit
indicates that the tool should be charged. See Figure D above.
Caution: Do not overcharge the Battery. Never charge for more than 10 hours
continuously. Charger Adapter should not be left plugged in after charging is complete.
OpERATInG InSTRuCTIOnS
1. Snap in the desired hex driver into the front of the Cordless Screwdriver. See Figure E
below.
Figure E
2. If light is needed while driving screws, turn on the Front
Operation Light Switch (see Figure D for its location).
The light will turn on when the Trigger Switch is on.
Insert Screwdriver
Bit Here
3. Engage the screwdriver bit over the item being turned.
The bit size must match the size of the item being
turned.
Screwdriver Bits
4. Squeeze and hold the top part of the Trigger Switch
(14) to begin clockwise operation. For counterclockwise operation, squeeze the lower
part of the Trigger Switch.
REV 07a
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 8
TROuBLESHOOTInG
problem
possible Cause
probable Solution
Cordless Screwdriver does Battery Pack is not charged.
not operate when Trigger
Recharge Battery Pack.
Switch is pressed.
Battery Pack does not
recharge after connecting
Charger Adapter for hours.
1. No power to Charger
Adapter.
1. Check electrical outlet for
power.
2. Charger Adapter defective. 2. Replace Charger Adapter.
3. Battery Pack defective.
3. Replace Battery Pack.
MAInTEnAnCE
1. When finished using the Screwdriver, place in its box along with accessories and store
in a clean and dry location.
2. Recharge the Battery Pack (22) once a month.
3. Properly recycle Battery when Screwdriver reaches the end of its product life.
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 9
pARTS LIST
part
1
2
3
4
5
6
7
8
Description
Output Axis
Gasket
Qty
1
1
1
1
1
1
1
1
1
1
1
1
part
13
14
15
16
17
18
19
20
21
22
23
24
Description
Qty
1
1
1
1
1
1
1
1
1
1
1
1
Motor
Trigger Switch
Housing (left / right)
LED Indicator
Light Cover
Gearbox
Ring, Inner, Self-lock
Core, Inner, Self-lock
Block, Self-lock
Gear, Front Star
Holder, Star Gear, Middle
Gear, Star, Back
Gasket, Large
Motor Holder
Light Bulb
Switch, Light
Connector Pin
PDC
Battery Pack
Charger Socket
Charger Adapter
9
10
11
12
Motor Gear
nOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
ASSEMBLy DRAWInG
pLEASE READ THE FOLLOWInG CAREFuLLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTA-
TION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURERAND/OR DISTRIBUTOR EXPRESSLY STATES THATALL REPAIRSAND PARTS REPLACE-
MENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.
THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF RE-
PLACEMENT PARTS THERETO.
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 10
LIMITED 90 DAy WARRAnTy
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we will
either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost of
returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 95065
For technical questions, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 11
|