Fully Automatic Washing Machine
User's manual
This manual is for
HWM78-0528T
Special number:
Please read this manual
carefully before using.
Retain it for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing list
Names of the parts
Water inlet valve
Top lid component
Detergent box
Water absorption
cushion
One
One
User's manual
Warranty card
Inside the document bag
Inside the document bag
Power cord
Control pannel
Lint filter
Handle
Components of the water inlet
hose
Balance ring
Inner tub
One
Inside the accessory bag
Drain hose
Pulsater
Front control
board
Cabinet
Lint filter
Fixed leg
(3 pieces)
Inside the document bag
One
Drain hose frame
Adjustable
leg film
Back cover
Adjustable leg
Tapping screws
Bottom plate
Eight
Inside the accessory bag
Meaning and description of the symbols
Between the upper cushion of the washing
machine package and the upper seal of the
package carton
One
One
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
Warning sign
Automatic washing machine
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Forbidden sign
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting answer to question
Safety precautions
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not
breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
The washing machine must be positioned so that
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.
Phenomena
The reason
How to settle
Buzzing upon reservation starts,
the digitron displays "E0"
The top lid is not closed
Close the top lid
Put down the drain hose. Open
and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Is the drain hose put down?
No or slow drain, the digitron
displays "E1" , buzzing.
Earth
Is the drain hose blocked by
foreign material?
Running pauses during spin,
the digitron displays "E2",
buzzing
The top cover leaves open
Close the top lid
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.
Re-order the laundries. Close the
top lid.Level the machine in right
position.
Are the laundries put slantingly?
Is the machine slanting?
Safety switch actuates, not
spin, (after self-correction
twice), the digitron displays
"E3", buzzing
Open and close the top lid once.
Open the water tap.
The water tap is not open
No or slow water filling (not
reaching the level in 30 min),
the digitron displays "E4",
buzzing
Push the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
The water inlet valve is blocked
The water pressureis too low
and the current is too small
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.
Do not use water hotter than 50
.
Please contact the after-sales
service department.
The water level sensor is bad.
The digitron displays E6.
Poor or no waterfall flow
The ventilation
holes at the bottom
If the nozzle is choked with
foreign bodies
Remove the foreign bodies
Back
Is there power failure?
Is the power plug loose?
Use it when the power is on.
Soft object
Front
Insert the power plug tightly.
Affusion to the set water level.
Not wash
The machine does
not act
Does the water level arrive at the
set water level?
Is the power plug loose?
Is the top lid closed?
Insert the power plug tightly.
Close the top lid
Not spin
Are the laundries put orderly?
Put the laundries orderly.
Is the machine slanting?
Level the machine properly.
Re-order the laundries.
There's abnormal sound inside the
machine
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Are the laundries slanting in
spinning?
Is the jointer screw of the water
inlet hose is loose or twisted
awry?
Fasten the jointer screw
properly.
The water faucet leaks
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure pauses.
The cloth sensor is detecting , it will add water
after about 48 senconds.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
The program is setting the drain time , certain
period is needed before it starts spinning.
Select spin program, but it does not work.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Disposal after washing
Do not decompose, repair or alter the machine
by yourself.
Do not stretch hands into the working machine.
It is dangerous even if the rotation is slow.
Take special care of the children.
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Clean the detergent box and set it on
the control panel seat.
The lint filter must be used during washing.
It must be cleaned in time after each using
Lint filter:
1.Pull it up to dismantle.
2.Push it down to install.
3.Clean the filter screen after washing.
Do not put any hot or heavy items (such as the kettle
with hot water) on the washing machine
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Dismantle
Install
Dismantle
Install
Benzene
Clean
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol,
alcohol etc.
The filter screen of the water inlet valve is
likely to be blocked by foreign materials
and influence the water inlet. Please clean
it with brush every two months.
The appliance is not instruct for use of young
children of infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
Keep the machine away from direct sunlight and
heat source like the heater.
ol
etr
P
hinner
T
Alcohol
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after
each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for
some time (about 1 hour), then close the top lid.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and adjustment
Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.
3 Push the " WATER LEVEL "button,select suitable water level
Install the bottom plate
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level.
After you open the package, please lean the
Back
washing machine gently down on soft items ( like
the towel cloth, blanket, etc. ). Install the bottom
plate to the bottom of the machine with the eight
screws by across screwdriver, then lift the machine up
gently.See to the figure:
4 Push the "PROGRAM/RESERVE" button to select suitable reserve
wash program
Front
Bottom plate
Soft items
Screw
After switching on the power, the reserve program is not set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the "PROGRAM/RESERVE"
button to set the reserve wash program two seconds. Refer to "PROGRAM/RESERVE"
button in Page 11 for selection.
Adjust the Installation position
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
the washing will be finished after 18 hours.
5 Push the "Start/Pause" button
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
the adjustable nut
the adjustable leg
Fasten
Low
6 Finish washing
Loosen
High
2 . After adjustment, fasten the nut.
After finishing wash it will switch off power automatically
Download from Www.Somanuals.com. All Manuals Search And Download.
How to change the direction of the drain hose
Steps of using the operation buttons and
description of the steps
b
1.Dismantle the rear cover of the washing machine.
3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.
2.Put down the drain hose .Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet ,then nip the drain fixing clamp to make it
deviated from the clip,the other hand is used to put down
the drain bushing,as indicated in Figure 2,3.
4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.
PROGRAM
STANDARD
SOAK HEAVY
GENTLE
SAVE
Drain outlet
protecting cover
INDICATION OF PROCESS
COTTON
TIME REMAINED(M INUTES)
RESERVE(HOURS LATER)
(NO CHOOSING)
SOAK
WASH
RINSE
SPIN
POWER
ON/OFF
SINGLE WASH
RINSE SPIN
SINGLE SPIN
WATER
LEVEL
Digital display
TUB CLEAN
AIR DRY
Fuzzy logic co
Drain hose
10 water level
START
PAUSE
PROGRAM/RESERVE
Figure 5
Figure 4
Drain hose support
Cabinet
Drain bushing
Figure 2
Drain bushing
Figure 1
5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6
Inner
Push
Outer
Drain bushing
Take down
Drain hose fixing
clamp
1.Push "POWER"button to switch on the power
Figure 6
POWER
ON/OFF
Figure 3
Push
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .
2.Push "PROGRAM/RESERVE" button to select
suitable automatic program
PROGRAM/RESERVE
Usage the drain hose
After the power is switched on, "standard" is automatically set. To select other full-auto program, please push
the "PROGRAM/RESERVE" button till the corresponding indicator is on. Refer to the "PROGRAM/RESERVE
button" on Page 11.E.g
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
For instance:select "SAVE" program for small quantity of laundries with light soil.
2.Do not step on or press the drain hose.
Program select
The running process
(the digitron displays the running process)
Program
Application
The display of digitron
WASH(
SOAK(
)
)
SPIN(
RINSE(
SPIN(
SPIN(
)
STANDARD
SOAK HEAVY
GENTLE
Common washing
RINSE(
WASH(
RINSE(
RINSE(
)
)
)
)
01
02
03
Washing for coverlet bigger laundries
)
SPIN(
)
)
WASH(
WASH(
)
)
Washing the woollen silk textiles
Washing for normal laundries
Washing the cotton textiles
)
SAVE
04
05
06
3. If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
5.If the extra hose is too long, cut it either at A or at B.
COTTON
WASH(
WASH(
)
)
SPIN(
)
RINSE(
)
SINGLE WASH Reusing the washing detergent
Washing the cloth washedby hand
RINSE SPIN
RINSE(
)
SPIN(
)
07
08
(first draining, then spinning)
Only spinning the cloth wetor washed by
SINGLE SPIN
hand (first draining, then spinning)
SPIN(
SPIN(
)
)
The spinning time is thesame to the single spin,
but spinning in lower
TUB CLEAN
09
10
Avoid growing mildew on the outer tub and the
AIR DRY
inner tub
SPIN(
)
5
12
Download from Www.Somanuals.com. All Manuals Search And Download.
"Power" button
Reserve,Process,remain time digitron
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If the
"start/pause" button is not pushed, the machine will
switch off the power automatically after 5 minutes.
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes.E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
HT
LIG
ED(M INUTES)
URS LATER)
H
AS
FL
POWER
ON/OFF
WATER
LEVEL
Digitall display
Fuzzyy logiic control
10 wateer leveel seleection
PROGRAM/RESERVE
WATER LEVEL button
PROGRAM/RESERVE button
The washing machine can detect the laundries automatically.
After detection,it will set the water level to suitable value among
4, 6, 8,and 10 automatically.
Push down the "program/ reserve" button. You
can select one program of ten which is
standard,soak heavy, gentle,save,cotton,
single wash,rinse spin,single spin,tub clean,
air dry;
You can also set water level by yourself. After the machine is
started, it will not set water level automatically. You shall push the
"start/pause" button to make new setting.
Push the"program/ reserve" button to set the
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .
reserve wash program morethan two seconds
continuously;
If save program is selected, it will display water level 2 .
When water level 2 is reached in water filling, it will perform
washing while filling water.When water level 3 is reached, it will
change to normal washing.
When the "reserve" function is activated, the
indicator light of the program you have set
will be off. The "reserve (hour)" and "time
remain" indicator lights will be on;
During operation of wash and rinse program, you can push down
the "water level" button to add water. When you release the button, or
it reaches the overflow water level, the machine will stop adding
water.
During reserve procedure, push the "reserve"
button to display the reserve mode.To change
the running program or cancel the reserve
setting, you need to switch off the power
and make new selection;
The water level decided may be different from actual value because
of the different moisture level of the laundries.
Attention As selecting the waterlevel 1,3,5,7,9;the light
is Flashing;
As selecting thewater level 2,4,6,8,10;the light
is lighting;
Download from Www.Somanuals.com. All Manuals Search And Download.
Off:
Flashing: indicate the running program
On: indicate the program about to run, or
indicate the selected mode
PROG
RAM
NDARD
STA
SOAK
HEA
VY
GENTLE
SAV
E
INDICA
TION
OF P
ROCESS
COT
TON
(NO
CHOOSIN
G)
SING
LE
W
ASH
TIME REMAIN
RESERVE(HO
SOA
WAS
K
H
RINSE
SPIN
E SPI
SINGL
N
RINSE
SPIN
TUB
AIR
CLEAN
DRY
START
PAUSE
START/PAUSE button
After the power is switched on,press it to
start the machine
During working,push it to pause.
During pause,push this button to restart and
go on working
Download from Www.Somanuals.com. All Manuals Search And Download.
1.Preparation before washing
2.Put in the laundries
Download from Www.Somanuals.com. All Manuals Search And Download.
|
HannsG Car Video System HX193 User Manual
Honeywell Home Security System LYNXR 2 User Manual
Hoshizaki Dishwasher JWE 2400CUA L 25B User Manual
HP Hewlett Packard Computer Drive A165890669 User Manual
HP Hewlett Packard Printer WP36 50 User Manual
HP Hewlett Packard Switch HP 8753C User Manual
Huffy Fitness Equipment 89225 User Manual
Hypertec Mouse Z12568ZHY User Manual
IBM Garage Door Opener 38 User Manual
IGo Direct TV Cables USB Charging Cable User Manual