Fully Automatic Washing Machine
User's manual
This manual is for
50FREE-3B
Please read this manual
carefully before using.
Retain it for future reference.
Special number:0030805269B
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting answer to question
Names of the parts
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Water-absorption
gasket
Water inlet valve
Top lid
Inner cover
components
Control
panel seat
Phenomena
The reason
How to settle
Hang up to suitable height . Open and close the
top lid once.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose hang up to suitable
height?
Is the drain hose blocked?
Lint filter
Inner tub
Clean the foreign material. Open and close
The top Lid Once.
Handle
Hook
Out tub
cover
Pulsator
It stops running in midway. The digitron
displays E2.
Close the top lid.
The top lid is not closed.
Control
panelfilm
Power
cord
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Cabinet
Drain
hose
Back
cover
Open the water tap. Open and close
the top lid once.
Clean the water inlet valve then open
and close the top lid once.
Open and close the top lid once.
Hang up to suitable height .
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Is the drain hose hang up to suitable
height?
The water filling does not work, or is
slow, the digital displays E4.
Base
Fixed foot(3 pcs)
Adjustable foot
Adjustable foot
film
Please contract the after-sales
service department
The water level sensor is bad.
The digitron displays F1.
Not wash
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
The machine does
not act
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Not spin
Meaning and description of the symbols
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
There's abnormal sound
inside the machine
Is the jointer of water
inlet hose loose or awry?
The water tap leaks
Warning sign
Fasten the jointer properly.
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
Select spin program, but it does not work.
The program is setting the drain time , certain
period is needed before it starts spinning.
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in
damage of the machine or influence the personal safety of
the users.
Forbidden sign
The pulsator pausesduring water
inlet in washand rinse.
It is toavoid splashing duringwater inlet
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
16
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence
your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Please insert the power cord into special rece- The power cord plug should be convenient
ptacle with rated voltage.If the power cord is to be pluged in or pluged out with hand
three-phase wire,please use three-phase rec- while the washing machine runs normally.
eptacle.The earthing terminal of the receptacle Be sure to pull the plug out and close the
must be earthed reliably.If it is two-phase wire, water tap when the machine is idle,when
please guarantee that the earthing wire is ear- moving the machine,or when cleaning
thed reliably.If possible ,please adopt electric the machine.Do not use wet hand to ins-
The lint filter must be used during washing.
It must be cleaned in time after each using.
Up
leakage protector.
ert or pull out the power plug.
Install
Lint filter:
1.Push down the spring piece of the top lint filter to
Dismantle
make the claws out of the filter cover, and then
Down
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can get
Figure 1
Do not damage the power cord,bend ,extend,twist,bind or alter it by force.Do not press or
nip it with weight.If the power cord or the power plug is bad, or the power plug becomes
flexible,to avoid risk it is required to have it replaced by the technicians of our special
shop or the costomer care agent. Keep the pin of the power plug clean,if the
power plug is polluted with dust,please wipe with dry cloth carefully.
down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
Up
The back cover of lint filter
Dismantle
5.Put the lint filter into filter cover, and make it tight .
Install
6.Make sure the lint filter well installed, or it can
influence your use.
Down
The front cover of lint filter
Figure 2
Do not put the machine at damp place like
Do not use water hotter above 50 C .
the bathroom. Never wash it with water.
Not put wet laundries on the control panel.
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
In case the washing machine is installed
Do not wash water-proof laundries like
on ground with carpet, do not block the
ventilation hole with carpet.
abnormal vibrations.
the raincoat, bike covers etc. to avoid
The ventilation holes
at the bottom
soft items
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
2
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.Do not let the children
climb the washing machine.
Do not decompose, repair or alter the
machine by yourself.
Water Level and Time Table for Each Program (self programming not included)
Water
level
Rinse(minutes)
Total time(minutes)
About 43
Wash(minutes)
About 18
Spin(minutes)
About 4
Program
Rinse twice, about 17
STANDARD
Save
1~4
Saving water program, total about 10 minutes
Rinse twice, about 17
1
About 10
About 31
About 4
About 4
About 6
GENTLE
1~4
SOAK+WASH
about 40
About 65
Rinse twice, about 17
HEAVY
1~4
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
Totaltime will add3
9 minutes duringDISINFECT selected
l
tro
r
e
Pe
inn
h
T
Attention:
Total time: including the normal water inlet time and drain time.
Spin time: the time from intermittent running to finishing
When selecting SAVE wash program, wash, rinse and spin are set
automatically.
*
*
*
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
5 Push START/PAUSE button
START
PAUSE
5 Close the top lid
If you open the top lid, the machine will stop
working except for water filling and draining
To prevent your laundries and washing
machine from damage,be sure to take
out all of the foreign materials from your
pocket,such as coins,buttons,sand or
hair pins etc.
Please keep the lint filter in good condition,
and install it to proper position. If the lint
filter is lost or damaged, please contact
costomer care agent of our company.
6 Washing finished
Install
Before washing,please check if the water
tap is open ,and if the water inlet pipe is
connected properly.
Dismantle
The power will be switched off automatically
after the finishing of the washing.
It is suggested to use low-foaming was-
hing powder
After the finishing of
the washing,It will
give an alarm
3
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
After switching on the power, the washing machine will set to common program including"wash, rinse,
spin "automatically.To select other procedures, push the " WASH"," RINSE"or "SPIN"button to select the
time of wash and spin, and the times of rinse. After switching on the power,if you push one of the
button among "RINSE"and"SPIN the digitron of the former procedures will turn off automatically. The
former procedures will not run. For instance: after switchingon the power. If you push the "SPIN" button
first, it will execute spin singly after starting.
Install the inner cover
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming the inner cover
shaft to the installation hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub
cover shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component after washing.
Outer tub cover
Attention
Even there's no water in the tub, a certain period is
required before spin starting.
Separate the laundries that are not colorfast from
other laundries in washing.
Right hand
Outer tub cover shaft groove
Do not use the HEAVY program for the woollen textiles.
The pulsator will not rotate unless the water is
filled to water level .
Inner cover shaft
Left hand
Inner cover component
After the machine starts operation, you can set the program and procedure during washing,
set spinning time during rinsing but can not make setting in other cases.
Figure 2
Figure 1
Install the bottom plate
Back
Front
After you open the package, please lean the washing
machine gently down on softitems ( like the towel cloth,
blanket, etc. ). Install the bottom plate to the bottom of
the machine with the eight screws by a cross screwdriver,
then lift the machine up gently. See to the figure:
Press " WATER LEVEL "button,
select suitable water level
WATER LEVEL
Bottom plate
Screw soft items
After switching on the power, select a suitable water level to detect the cloth. To select other water level.Refer
to "water level, water quantity and desoge of powder"in Page 9 and "WATER LEVEL/DISINFECT"button in Page
10 for the selection.
Adjust the installation position
The washing machine shall be more than 20mm away from the wall.The largest allowed
slope of the supporting base of the machine is 2 . The slanting or rough ground will
result in unstable running or stoppage of the machine. Please adjust it with following
methods:
Page 10
Page 9
Confirm it's horizontal:
Hang the lead line to confirm if it is horizontal.
Adjust the adjustable foot:
1.To twist the adjustable foot, please first
lift up the side of the foot slightly, loosen
the adjustable nut, and twist the foot.
2.Fasten the nut after adjustment.
adjustable nut
Loosen
Fasten
adjustable foot
High
Low
4
13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to change the direction of the drain hose
Steps of using the operation buttons
and description of the steps
b
1.Lean the machine down gently with the front
surface facing the ground. Loosen the eight
screws by a cross screwdriver.
3.Extend the drain hose from the left side. Push the
drain hose into the groove with hands.
Bottom plate
Back
Push the drain hose
into the groove with
Front
POWER
ON/OFF
Soft item
START
PAUSE
MIN
2.Pull out the drain hose from the groove at the
right side.
4.Install the bottom plate (as per indicated before),
then lift the machine up gently.
Use groove at
this side after
direction changing
1 Push the POWER ON/OFF button to
switch on the power
POWER
ON/OFF
After switching onthe power,DISINFECTis not selected
To select DISINFECT,push WATERLEVEL/DISINFECT over 2 seconds,
the DISINFECT function works,then push2 or 3 to select asuitable program.
Using the drain hose
2 Push the PROGRAM SELECTION button to
select the suitable automatic program
PROGRAM
The drainage shall be smooth with the drain hose.
1.put the drain hose up to suitable position (Do not
put it on ground.)
Notes: The highest point of drain pipe shuold be
higher than the water level of washing tub for
avoiding to siphon phenomenon during drain.
After switching on the power, the machine will set to STANDARD program automatically. To select other
program, push the PROGRAM SELECTION button till the corresponding indicator is on. Refer to the
PROGRAM SELECTION button in Page 11.
2.Do not step on or press the drain hose.
For example: select SAVEwashfor the quick washing of
the laundries with light dirt.
Page11
3 Push WASH RINSE SPIN button to select
suitable programs
0.7m<H<1.2m
MIN
12
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the water inlet hose
Power On/Off button
button to switch on
s on, push it again
Push the POWER ON/OFF
the power. When the power i
to switch off the power.
Wash remain time indicator digitron
The program is selectedbut not on,It displays the total minutes
of the program
button to switch on
Push the POWER ON/OFF
the power. If the START/PAU
pushed, the washing machine
switch off the power after 5 m
During operation of programs, it displays the remained time (minute).
SE button is not
will automatically
inutes.
In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16)
1. Attach the water inlet hoses to the water faucet. Using pliers, tighten
the coupling. ( As figure 1)
Page 16
NOTE: Do not over tighten. Damage to the
valves can result.
Start/Pause
After the power is switched on, push it to
button
Start the machine
During working, push it to pause working.
During pause, push it to resume working.
2. Connect the other ends to the water inlet valve .
( As figure 2)
Figure 1
Jointer of the water inlet hose
POWER
ON/OFF
Jointer of the
water inlet valve
START
PAUSE
Figure 2
Water absorption cushion
WASH button
PROGRAM SELECTION button
Push the WASH buttonto set the wash
procedure.
You can select from the following four programs.
During STANDARD GENTLE HEAVY
programs, push theWASH button to set
different wash time (STANDARD from0 to
25minutes GENTLE from 0 to 15
minutes;HEAVY from 30 to 50 minutes or 0
minutes )
Normal wash
STANDARD
HEAVY
Large, thick or heavily soiled laundry
Woollen textiles or underwear
GENTLE
SAVE
10 min quick wash for load below 2 kg
During SAVE program, push the WASH
button, the machine have no reaction.
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Use the operation buttons
A.
Description of the function of the buttons
Check the connection between the water inlet
hose and the water tap
Mode and meaning of the indicator light
Digital tube
Off
During operation of programs, it displays the
remained time (minute) or remained times of
the corresponding procedure
1.Swaying the hose gently to confirm if it is fastened
stable.
Flashing: indicate the runningprogram
On: indicate the programabout to run, orindicate the selected mode
2.After installation, open the tap to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the water inlet hose and the water tap, is firm,
so as to prevent dropping from improve Installation
position.
Take down the water inlet hose
1.Close the water tap.
2. Pull off the water inlet hose from the water tap and washer
MIN
Push WATER LEVEL/DISINFECT button to select a
suitable water level.
After the machine is started, You shall push the START/
-PAUSE button and then push WATER LEVEL/DISINF
-ECT button make new setting.
During SAVE program,WATER LEVEL/DISINFECT
will not be changed.
button
RINSE
utton
N b
SPI
During operation of wash and rinse program, you can
push down the water level button to add water. When you
release the button, or it reaches the overflow water level,
Push the RINSE button to set
Push the SPIN button to set
the spin procedure.
the rinse procedure.
During STANDARD GENTLE
HEAVY programs,push the RINSE
button to set different rinse times
During STANDARD GENTLE
HEAVY programs,push the
spin button to set different spin
the machine will stop adding water .
Push WATER LEVEL/DISINFECT over 2
seconds , DISINFECT tube is light;Push
WATER LEVEL/DISINFECT over 2 seconds again,
DISINFECT tube is off and the DISINFECT function
is canceled.During the washing maching working,
push START/PAUSE button ,you can make
new selected.
(
0, 1, 2, 3, 4 times)
minutes
(
0
9 minites)
During SAVE program,push
the rinse button,the machine have
no reaction
During SAVE program,push
the spin button,the machine have
no reaction
10
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Preparation before washing
3 Add the detergent
Preparation before washing
1.Connect the water inlet hose and open the water tap .
2.Confirm that the washing machine isearthed reliably . The
insert the powerplug into the receptacle. Do not connect the
earth terminal to the gas pipe and tap water pipe.
3.Put up the drain hose.
How to use the washing
powder
Direct dissolved in the machine
1.Fill water to "1" level.
0.7m<H<1.2m
2.Add the power. Run for 30 seconds to
dissolve it completely.
3.Put in the laundries. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 C and a container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
Washing powder with poor quality or not used
for a long period may get blocked. Please
clean the detergent box in time.
4.Slanting or uneven ground may result in unstable working
or abnormal noise. Please make the machine stand horizontally.
How to usethe whitener
Pay attention to followings before washing the laundries
Fill water to decided level. Dilute the whitener
with container. Pour it slowly into the washing
tub.
Avoid using whitener on laundries with color
or pattern as they are prone to lose color.
The whitener shall not touch the laundries
directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before
use.
Clear the pocket.
Confirm
if
When the pulsator is running,
the buttons of the laundries
may cause noise. For the
sake of discretion,please
put the laundries with buttons
into other laundries.
Fasten the
buttons and
zippers.
The quantity of
the laundries
shall not exceed
the rated value.
The big laundries
like the jeans
shall be put in
loosely.
Take out the
coins , sand,
hairpins etc.
there's special
requirment for
the laundries.
Different washing powders have different
dosage. Please refer to the usage manual of
the washing powder for the details.
Standard usage quantity of the detergent and water
quantity
a.Please check if the laundries are applicable for washing.
b.Separate those not colorfast from other laundries.
Concentrated
powder
(Add 25g in each
30L water)
Common powder
Laundries
quantity(kg)
Water level
Water quantity
c.For laundries not waterabsorbing,please put them into water with hands.
d.For laundries with much soil,please remove the soil first.You can add detergent on the
part with serious soil directly.It is much easier to remove the soil by that mean.
e.For laundries likely to get lint ball or with long fiber,please first turn the inside out before
putting them into the water.
(Add 40g in each
30L water)
About 32L
About 26L
About 42.7g
About 34.7g
About 26.7g
About 21.7g
4
3
1.5~3.3
1.5
f.Do not put the laundries polluted with chemicals directly into the washing machine.
About 21L
About 17L
About 28g
About 21.3g
About 17.5g
About 13.3g
2
1
2 Put in the laundries
The capacity of washing and spinning of the machine refer to the largest weight
of the standard laundries under dry condition that can be washed or spun in
one time. One time washing quantity shall be lower than the rated capacity.
The thicknesses, size, type of the cloth will influence the actual washing capacity.
It is suitable for one time washing to put in reasonable amount of laundries and
the laundries can be turned round in washing.
Do not select 4 water level for laundries smaller than 0.8kg, so as to avoid
splashing of water.
9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|