Domestic Dishwasher
HDW201WH
HDW201SS
User Manual
Co d e :0120502719
Download from Www.Somanuals.com. All Manuals Search And Download.
In te rio r Vie w
Washing Filter
G Turbo Dry-fan
A Upper Rack
F
B Rack Height Adjustor
C Top Spray Arm
D Lower Rack
H
I
Detergent and Rinse Aid Dispenser
Third Sprayer
E Bottom Spray Arm
Technical Information
Width
Depth
Height
60cm
60cm
85cm
Capacity
12 standard place settings
0.03 – 0.6 MPa
220-240V~
Mains Water Pressure
Power Voltage
Total Power
2200 W
.2.
Download from Www.Somanuals.com. All Manuals Search And Download.
De te rg e n t a n d Rin s e Aid
Detergent
Rinse Aid
This product makes dishes sparkle and helps them to dry without
Only detergents specifically intended for use with dishwashers must
be used. The dispenser must be filled before the start of each wash
cycle following the instructions provided in the "Wash Cycle Table."
The detergent dispenser is located on the inside panel of the door.
spotting. The dispenser is located on the inside panel of the door
and should be filled after approximately 80 wash cycles (or when
the rinse aid indicator light comes on for those models with this
feature).
Loading the Detergent
Loading the Rinse Aid
Open the cover "A" on the dispenser, press the button "B". Then
Open the dispenser by turning the cap "C" in an anti-clockwise
pour the detergent for the wash cycle into the compartment "C".
After the detergent has been loaded, close the cover and press it
down until it clicks into place.
direction and pour in the rinse aid. ( Do not overfill ). To regulate the
amount of rinse aid dispensed during each cycle, turn the dose
adjuster "F", located beneath the cap, with a screwdriver. There are
6 different settings; the normal dosage setting is 3.
C
Important
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs, the
dosage adjustor should be turned to a higher setting. If the dishes
have white streaks, turn the dosage adjustor to a lower setting.
B
Note : Remove excess detergent from the edges of the
dispenser before closing the lid
.3.
Download from Www.Somanuals.com. All Manuals Search And Download.
Lo a d in g th e Dis h wa s h e r
Before placing the dishes in the dishwasher, remove larger food
particles to prevent the filter from becoming clogged.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they are soaked before washing. This
will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.
How to use the lower rack
Place the most difficult to clean items on the bottom rack: pots,
pans, lids, serving dishes and bowls, as shown in the fig. to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The lower rack features fold down tines (see fig.A) so that larger
or more pots and pans can be loaded.
- The cutlery basket ( fig. B ) can be halved so that only one section
can be used when the cutlery load is light. This makes space for
additional pots and pans and also allows it to be placed in the
upper rack.
- Cutlery should be placed in the basket with the handles down
(except for teaspoons). If the basket has guides, the spoons
should be located individually into the appropriate slots. Extra long
utensils should be placed horizontally at the front of the upper
rack.
How to use the upper rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small bowls
and shallow pans (as long as they are not too dirty). - Position the
dishes so that they are not moved by the jets of water.
The upper rack can be adjusted for height by using the handles lo-
cated on the sides of the rack (see fig.C).
Folding shelf
Lean tall glasses and those with long stems against this shelf, not
against other items to be washed (see fig.D).
Long cutlery items, salad servers or knives should be placed on the
shelf so that they do not obstruct the rotation of the spray arms. The
shelf can be folded back when not required (see fig.E).
.4.
Download from Www.Somanuals.com. All Manuals Search And Download.
Op e ra tin g th e Ap p lia n c e
Starting a Wash Cycle
At the end of the Wash Cycle
After completing the installation, turn on the water and press the
ON / OFF button (A) located on the control panel. The indicator
light "B" will come on indicating that the appliance is on, but you
must wait a few seconds before programming the cycle.
Six beeps will indicate that the wash cycle has finished and the
cycle indicator light (H) will turn off. Turn the appliance off using the
ON-OFF button. Turn off the water supply to the appliance and
open the door. Wait a few minutes before unloading the
dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry
better.
Selecting a Wash Cycle
Select the desired cycle by pressing the selector button (G). Each
time the button is pressed, one of the cycle indicator lights "H"
will come on. Choose the wash cycle you feel is most
appropriate for the type of dishes that need washing from the
wash cycle chart on page seven.
Setting the Wash Cycle with a Delayed Start Time
After selecting the wash cycle as indicated in the paragraph
entitled, "Setting and Starting a Wash Cycle..." the delay time can
be set.
Press the Start / Pause button (I), and after a few seconds a
short beep will indicate that the wash cycle has begun and can
no longer be changed. If necessary, read the next paragraph,
"Cancelling or altering a cycle while underway..."
By pressing the button "E" (see close-up view-'Control panel") the start
of the wash cycle can be delayed for between 1 to 9 hours. Each time
the button is pressed, the display (F) will show the number of hours
for the delay period. Select the desired delay and push the Start /
Pause button "I". The machine will beep and the delay time on the
display will blink, indicating that the countdown has begun. After the
time has lapsed, the cycle will start.
Cancelling or altering a cycle while underway
A cycle that is underway cannot be altered.
It must be stopped by pushing the ON-OFF button (A) to
cancel all the settings and then restarted as described in the
preceding instructions. If the cycle is stopped after it has been
running for some time, the detergent may have already been
used, and the appliance may have already drained the wash
water. If this is the case, the detergent dispenser must be
refilled (see the paragraph entitled, "Loading the Detergent").
NOTE:
a) During the delay period, do not change any of the settings.
If it is necessary, all of the settings must be cancelled by pressing
the ON-OFF button (A) and the machine re-programmed following
the instructions contained in the preceding sections.
If you forget to load some of the dishes
b) If the door is opened during the delay period, the indicator will
blink and beep, and the countdown will stop. It will continue when
the door is closed.
To load additional dishes, push the Start/Pause button to
interrupt the cycle, load the dishes then turn the appliance back
on using the Start / Pause button. The cycle will continue from
where it left off.
Was h Cycle Adjus tment Buttons
Wash Cycle Programme Light
1/2 Load Button
The wash cycle is running when the cycle indicator light (H) is
This button "C" makes it possible to wash dishes using only the
blinking.
upper rack when there are not enough dishes for a full load. This
will save water and power. It can be used before setting any of the
wash cycles, except for the intensive cycle. Please keep in mind
that the amount of detergent should also be cut in half.
.5.
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- It is important to try and run the dishwasher when it is fully
loaded to save on energy.
- In order to prevent odours from forming and food from
caking onto the dishes, you can run the soak cycle.
- Choose the right wash cycle: the choice of cycle depends on
the type of dishware, cookware and utensils being washed and
how dirty they are.
How to Keep Your Dis hwas her in Shape
Moving the Appliance
After Every Wash
If the appliance must be moved, try to keep it in a vertical position. If
absolutely necessary, it can be laid on its back.
After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odours are not
trapped inside.
DO NOT LAY THE MACHINE ON ITS RIGHT HAND SIDE
Remove the Plug
Seals
Before cleaning or performing maintenance, always remove the
plug from the socket.
One of the reasons that odours form in the dishwasher is that food
remains trapped in the seals. Periodic cleaning with a sponge will
prevent this.
Solvents and Abrasive Cleaning Products
Do not use solvents or abrasive cleaning products to clean the
exterior and rubber parts of the dishwasher, use only a cloth and
warm soapy water.
When you go on Holiday
When you go on holiday, it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of the appliance
slightly ajar. This will help the seals last longer and prevent odours
from forming.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water and a little white vinegar, or a clean-
ing product made specifically for dishwashers.
Us e the right amount of detergent
If you use too much, the result will not be cleaner dishes, but a
greater negative impact on the environment.
- Large food particles should be rinsed from the dishes
before placing them in the dishwasher.
.6.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wa s h Cyc le Ch a rt
CYCLE
DETERGENT
TYPE OF LOAD
DESCRIPTION OF
CYCLE
Normal load of
dirty dishes, pots
and pans without
dried on residue
Cold pre-wash
Extended 50°C wash
Cold rinse
Hot 60°C rinse
Drying
30 g
Very dirty dishes,
pots and pans.
(Not to be used
with delicate items)
Hot pre-wash
Extended 50°C wash
Cold rinse
Hot 65°C rinse
Drying
30 g
15 g
Economic, fast
cycle to be used on
lightly soiled
Short wash at 40°C.
Cold rinse.
dishes right after
they are used.
No drying cycle.
Pre-rinse of dishes Short cold rinse to
while waiting for a prevent food residue
full load.
from drying on the
dishes
If we use the Rinse only.
The design need to
changed according to the
control panel. (
)
.7.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must be
kept clean.
The filter efficiently removes food particles from the wash water,
allowing it to be recirculated during the cycle. For this reason, it
is a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the semi-circular filter and
cup "A" under running water. To remove the filter assembly,
pull the handle in an upward direction. The entire filter as-
sembly (made up of the semicircular filter "A" and the fine filter
"B") should be cleaned at least once a month using a soft
brush. To reassemble, insert the entire assembly into the
dishwasher, by positioning it in its seat and pressing downward.
The dishwasher must not be used without the filters. Improper
replacement of the filters may reduce level of the appliance.
Cleaning the Spray Arms
Food particles can become encrusted on the spray arms and block
the holes (see Interior view on page 2", letters C & E ).
Check the spray arms periodically and clean them when necessary.
Troubles hooting
If the dishwasher does not function or does not function
properly, check the following before calling for assistance.
The Dishwasher Does Not Start
The Dishwasher Does Not Drain
- Is the plug pushed into the socket correctly;
- Is the drain hose kinked or bent.
- Is the power on in the house;
- Is the door closed properly?
- Is the ON-OFF switch "ON";
- Is the water supply turned on?
Lime Deposits or a White Film Form on the Dishes
- Is the rinse aid dosage correct?
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact you’re nearest authorised ser-
vice centre and provide them with the following information:
- The nature of the problem;
The Dishwasher Does Not Load Water
- Is the water turned on and the hose connected properly;
- Is the water supply to the house on?
- Is there sufficient water pressure?
- The model number (Mod...) and the serial number (S/N...), which
are located on the edge of the inner part of the door.
- Is the water supply hose crimped or bent?
- Is the filter in the water supply hose blocked?
For the name of your nearest Authorised Service Centre,
The Dishes Are Not Clean
Phone: 0800 2 HAIER (0800 24 24 37)
- Is the drain hose kinked or bent.
- Has the detergent been dispensed?
- Are the spray arms blocked?
- Are the spray arms rotating?
Always call an authorised technician and only allow
original spare parts to be installed .
P.8.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ins tallation
Positioning the Appliance
Drain Hose Connection
Position the appliance in the desired location. The back should Insert the drain hose into a drain pipe with a minimum diameter of
rest against the wall behind it, and the sides, along the adjacent 40mm, or let it run into the sink, ensuring there are no tight bends
cabinets or wall. The dishwasher is equipped with water supply or kinks. Use the plastic support (A) that comes with the appliance
and drain hoses that can be positioned to the right or the left to (see Fig.2). The free end of the hose must be at a height between
allow correct installation.
40 and 100 cm and must not be immersed in water.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screw them in
or out) to level the dishwasher. The appliance should not be
inclined more than 2 degrees to ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas) con-
nector and make sure that it is fastened tightly (see Fig 1).
If the water pipes are new or have not been used for an
extended period of time, let the water run first, till it is clear and
free of impurities. Otherwise the water inlet filter may get blocked.
Hot Water Connection
The appliance can also be connected to the house's hot water
Attention:
The plastic hose support must be fastened to the wall to prevent the
drain hose from moving.
supply following the same procedure as for cold connection.
This will reduce the wash cycle by about 15 minutes and the
wash efficiency will be slightly reduced.
Electrical Connection
DO NOT CONNECT TO A PUSH THROUGH HOT WATER
SYSTEM OR ONE THAT EXCEEDS A TEMPERATURE OF
60° C.
After making sure that the voltage and frequency values in the home
correspond to those on the rating plate (located on the stainless
steel inner door of the appliance) and that the electrical system is
sized for the maximum voltage on the rating plate, insert the plug
into an earthed electrical socket.
Anti-Flooding Protection
The dishwasher will retain any leaks within the unit, in order to
prevent damage to your home.
DO NOT USE ADAPTORS OR EXTENSION LEADS
.9.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|